Upload
others
View
1
Download
0
Embed Size (px)
Citation preview
INTRODUCTION
Low Maintenance
+ Less Operational
Downtime
Maximum
Serviceability
+ Exceptional Reliability
The Lowest Total Cost of Ownership
UNLEASH THE LOWEST TOTAL COST OF OWNERSHIP
This catalogue is about more than axles and suspensions. It is about customised solutions that always deliver on our promise of the lowest total cost of ownership. In fact, every piece of equipment you see in this catalogue is designed to the same formula:
It’s simple really.
Remember… when you choose York, you get a trusted partner. You can always turn to us for more information and advice to ensure you are investing in the best decision for your fleet and your business. We understand the challenges facing your company and what you need to give you that competitive edge. That’s a true partnership.
+ =
1.1 Suspension Application Chart
MT75
YTE75YTE75/90
YTE90
YTB90YTE115
Capacity (Per Module) 9T (8 Leaf x 13mm) 15T (10 Leaf x 16mm H/D) 18T (10 Leaf x 16mm) 25‐30T
10T (9 Leaf x 13mm) 20T (11 Leaf x 16mm) (8 Leaf x 20mm H/D)
15T (10 Leaf x 16mm H/D) 25T (11 Leaf x 18mm H/D)
11T (3 Leaf x 25mm) 25T (10 Leaf x 20mm H/D)
12T (13 Leaf x 10mm)
Application On & off road use. On & off road use. On & off road use. On & off road use.
Suit arduous outback
terrain & Agricultural
Industry.
Suit arduous outback
terrain, long haul driving
in outback & wharf work.
Suit arduous
outback terrain &
long haul driving in
outback.
H/D option for
predominately Mining &
Logging Industry.
H/D option for
predominately Mining &
Logging Industry.
H/D option for
predominately
Mining Industry.
To Suit Flat Top (Semi) Flat Top (Semi) Flat Top (Semi) Flat Top (Semi)
Drop Deck Drop Deck Drop Deck Drop Deck
Curtain Sider Curtain Sider Skeletal Skeletal
(Taut Liner) (Taut Liner) Tanker Tanker
Skeletal Skeletal Tipper Tipper
Tanker Tanker Side Tipper Side Tipper
Reefer Reefer Tip Over‐Axle Tip Over‐Axle
Tipper Tipper Bottom Dump Bottom Dump
Dry Freight Van Dry Freight Van Logging/Jinker Logging/Jinker
Side Tipper Side Tipper Livestock Hauler Livestock Hauler
Tip Over‐Axle Tip Over‐Axle Double Stacker Double Stacker
Bottom Dump Bottom Dump Bulk Hauler Bulk Hauler
Logging/Jinker Logging/Jinker Road Train Road Train
Livestock Hauler Livestock Hauler Dolly Dolly
Double Stacker Double Stacker Low Loader Low Loader
Bulk Hauler Bulk Hauler Widening Float Widening Float
Road Train Road Train Mining Mining
Dolly Dolly Sugar/Stock Sugar/Stock
Low Loader Low Loader
Widening Float Widening Float
Walking Floor Walking Floor
MECHANICAL SUSPENSIONSUSPENSION
Duratrac Tecair FB VRH Tecair 1 Tecair 2 Tecair Z10T 10T 11 T 9T 9T 40T (Max) @ 30Kph
12 T (Heavy Duty) (Walking Beam)
100T (Max) @ 10Kph
(Argonaut)
Mainly on road use
(>80%), suit quarry
app
Mainly on road use
(>80%), suit quarry
app
On & off road use. On & off road use. On & off road use. Off road H/D use.
Not suited for:
rigid tanker (i.e.
pressure vessel),
logging/jinker &
high centre of
gravity loads.
Not suited for:
rigid tanker (i.e.
pressure vessel),
logging/jinker &
high centre of
gravity loads.
Suit arduous
outback terrain.
Not for arduous
outback terrain.
Suit high axle loading in
arduous outback terrain.
Suits high centre of
gravity loads.
Not suited for high
centre of gravity
loads.
Suits high centre of
gravity loads.
Flat Top (Semi) Flat Top (Semi) Flat Top (Semi) Flat Top (Semi) Flat Top (Semi) Logging/Jinker
Drop Deck Drop Deck Drop Deck Drop Deck Drop Deck Low Loader
Curtain Sider Curtain Sider Curtain Sider Curtain Sider Curtain Sider
(Taut Liner) (Taut Liner) (Taut Liner) (Taut Liner) (Taut Liner)
Skeletal Skeletal Skeletal Skeletal Skeletal
Tanker (Non Rigid) Tanker (Non Rigid) Tanker Tanker Tanker
(Refer to York) (Refer to York) Reefer Reefer Reefer
Reefer Reefer Tipper Tipper Tipper
Tipper Tipper Dry Freight Van Dry Freight Van Dry Freight Van
Dry Freight Van Dry Freight Van Side Tipper Side Tipper Refrigerated Van
Tip Over‐Axle Tip Over‐Axle Tip Over‐Axle Tip Over‐Axle Side Tipper
Bottom Dump Bottom Dump Bottom Dump Bottom Dump Tip Over‐Axle
Dolly Dolly Logging/Jinker Logging/Jinker Bottom Dump
Low Loader Low Loader Livestock Hauler Dolly Logging/Jinker
Widening Float Widening Float Double Stacker Low Loader Livestock Hauler
Walking Floor Walking Floor Road Train Widening Float Double Stacker
Dolly Walking Floor Road Train
Low Loader Dolly
Widening Float Low Loader
Walking Floor Widening Float
Walking Floor
AIR SUSPENSION WALKING BEAM &
ARGONAUT
Standard Axles (12 - 13 Tonnes Capacity) with In-board Brake Drum.
Capacity Brake Wheel No. x Size of Brake Wheel Minimum Model Axle Weights(Bearing & Beam Size) Size Fixing Wheel Stud x PCD Type Bore Dia. Wheel Size Number Approximated
(mm) (mm) (mm) Kg
ISO 10 x M22 x 335 281 2021 335
JAP 8 x M20 x 285 221 2011 330
ISO 10 x M22 x 335 281 2022 382
JAP 8 x M20 x 285 221 2012 378
5021 351
5021G* 350
JAP 8 x M20 x 285 221 5015 354
420 x 220 ISO 10 x M22 x 335 281 5022 380
13.0 Tonnes 420 x 180 6021 351(TM & Square 6"/14mm) 420 x 220 6022 376
Notes:
1) 5" Round Axle - 16mm standard wall thickness, 19 & 25mm optional wall thickness.
2) 6" Square Axle - 14mm standard wall thickness.
3) Twin tyre steel wheel fixings are standard. ISO single wheel and twin tyre aluminum wheel fixings are also available.
4) Standard track length - 1850mm, other track lengths are also available.
5) All axles include standard manual slack adjuster, auto slack adjuster is optional.
6) Bearing size/type : TQ Metric 90-100 Bearing, TM Metric 65-90 Bearing,TN Imperial 2,5/8" - 90 Bearing,
TP Parallel imperial 89.6 Bearing, THU -Sealed Cartridge Bearing
7) All Axles are available with ABS ready Kits (Optional)
* 5021G New features, Single Spindle Locking Nut with improved Drum Hub assembly.
Coarse thread wheel studs available for India market applications.
12.0 Tonnes( TM & Round 5"/16mm )
420 x 180
420 x 180
420 x 220
12.0 Tonnes(TM & Square 6"/14mm)
20" / 22.5' P
P
ISO
ISO P 20" / 22.5'
10 x M22 x 335 281
28110 x M22 x 335
20" / 22.5'
Axle Page 1
Standard Axles (11 - 13Tonnes Capacity) with Out-board Brake Drum.
Capacity Brake Wheel No. x Size of Brake Wheel Minimum Model Axle Weights
(Bearing & Beam Size) Size Fixing Wheel Stud x PCD Type Bore Dia. Wheel Size Number Approximated.
(mm) (mm) (mm) Kg
11.0 Tonnes
(TM & Round 5"/16mm)335 x 210 ISO 8 x M22 x 275 P 221 19.5" 2950/7 306
11.0 Tonnes
(TN & Round 5"/16mm)335 x 210 ISO 8 x M22 x 285 221 19.5" 2950/5 306
12.0 Tonnes
(TM & Round 5"/16mm)420 x 180 ISO 10 x M22 x 335 P 281 20" / 22.5' 2041 335
2782/2 332
78792159
/R/ELS335
2782/3 335
2682/3 360
**2621 360
12.0 Tonnes
(TP & Round 5"/19mm)420 x 180 ISO 10 x M22 x 335 Q 281 20" / 22.5' 2682/3A 360
13.0 Tonnes
(TP & Round 5"/19mm)420 x 180 ISO 10 x M22 x 285.75 Q 220 20" / 22.5' 2682/2 360
Coarse
Thread**7635 330
ISO**7631*
330
10 x M22 x 285.75 Q 220 2582 353
10 x M22 x 335 Q 281 2583 356
11.0 Tonnes (MFL)
(THU 7 Round 5"/16mm)420 x 180 ISO 20" / 22.5'
13.0 Tonnes
( TP 150 x 165 /12mm )420 x 180 10 x M22 x 335 Q 281 20" / 22.5'
20" / 22.5' 78792280
/R/ELS345
10 x M22 x 335 Q 281 20" / 22.5'
12 Tonnes
(TP & Round 5"/16mm)420 x 180 ISO
10 x M22 x 285.75 Q 220
20" / 22.5"
78792157
/R/ELS332
10 x M22 x 335 Q 281 20" / 22.5"
12 Tonnes
(TN & Round 5"/16mm)420 x 180 ISO
10 x M22 x 285.75 Q 220
Axle Page 2
Freeway Baron
11.0 Tonnes (TM-90mm & Round 5"/16mm)
420 x 203 ISO 10.x.M22 x 335 Q 221 20 / 22.5" 2608 350
Highway King
Course
Thread5625 345
ISO 5626 345
13.0 Tonnes (TM-90mm & Round 5"/19mm)
420 x 203 ISO 10 x M22 x 335 Q 220 20" / 22.5' 2638 360
13.0 Tonnes (TM-90mm & Rec.150x165 -12mm)
420 x 203 ISO 10 x M22 x 335 Q 220 20" / 22.5' 7638 360
Notes:
1) 5" Round Axle - 16mm standard wall thickness, 19mm -25mm optional wall thickness.
2) Twin tyre steel wheel fixings are standard. ISO single wheel and twin tyre aluminum wheel fixings are also available.
3) Standard track length - 1850mm, other track lengths are also available.
4) All axles include standard manual slack adjuster, auto slack adjuster is optional.
5) Bearing size/type : TQ Metric 90-100 Bearing, TM Metric 65-90 Bearing,TN Imperial 2,5/8" - 90 Bearing,
TP Parallel imperial 89.6 Bearing, THU -Sealed Cartridge Bearing
6) (A)- Available in Australia only.
7) All Axles are available with ABS ready Kits (Optional)
8) *Coarse thread Wheel Studs on model 7630 is only available for India market.
9)** 2621 / 7630/ 7631 comes with new Hub greasing system .
10) *** 2611 ( Off Set 162mm Hub )
Car Carrier Axles
Capacity Brake Wheel No. x Size of Brake Wheel Minimum Model
(Bearing & Beam Size) Size Fixing Wheel Stud x PCD Type Bore Dia. Wheel Size Number
(mm) (mm) (mm)
11.0 Tonnes Car Carrier
(TM & Round 5"/19mm)420 x 180
Fine
Thread10 x M22 x 335 Q 281 20 / 22.5" ***2611 315
11.0 Tonnes Car Carrier
(TM & Round 5"/19mm)420 x 180
Course
Thread10 x M22 x 335 Q 281 20 / 22.5" ***2615 315
Notes:
1) 5" Round Axle - 19mm standard wall thickness, 25mm optional wall thickness.
2) ISO single wheel fixings.
3) Min Track Lenth 2050mm , overall length not exceeding 2500mm.
4) All axles include standard manual slack adjuster, auto slack adjuster is optional.
5) Bearing size/type : TM Metric 65-90 Bearing,
6) All Axles is available with ABS ready Kits (Optional)
Axle Weights
Approximated.
Kg
2013 New Axle Models ~ Standard Out Board
20 / 22.5"12. Tonnes
(TM & Square 6'/14mm)420 x 180 10 x M22 x 335 P 281
TRACK LENGTH 2050MM MIN
Axle Page 3
Heavy Duty Axles (15.0-25 Tonnes Capacity) with In-board Brake Drum.
Capacity Brake Wheel No. x Size of Brake Wheel Minimum Model Axle Weights
(Bearing & Beam Size) Size Fixing Wheel Stud x PCD Type Bore Dia. Wheel Size Number Approximated.
(mm) (mm) (mm) Kg
15.0 Tonnes
(TQ & Round 5"/25mm)420 x 220 ISO 10 x M22 x 335 P 281 20" / 22.5' 8002 400
16.0 Tonnes
(TQ & Square 6"/14mm)420 x 220 ISO 10 x M22 x 335 P 281 20" / 22.5' 5801 410
Heavy Duty Axles (15.0-25 Tonnes Capacity) with Out-board Brake Drum.
Capacity Brake Wheel No. x Size of Brake Wheel Minimum Model Axle Weights
(Bearing & Beam Size) Size Fixing Wheel Stud x PCD Type Bore Dia. Wheel Size Number Approximated.
(mm) (mm) (mm) Kg
Notes:
1) 6" Round Axle - 32mm standard wall thickness .
2) 6" Square Axle - 14mm standard wall thickness.
3) Inboard brake drums are standard.
4) Twin tyre steel wheel fixings are standard. ISO single wheel fixings are also available.
5) Standard track length - 1850mm, other track lengths are also available.
6) All axles include standard manual slack adjuster, auto slack adjuster is optional.
7) Bearing size/type : TQ Metric 90-100 Bearing, TM Metric 65-90 Bearing,TN Imperial 2.5/8" - 90 Bearing,
TP Parallel Imperial 89.6 Bearing, THU -Sealed Cartridge Bearing
8) All Axles are available with ABS ready Kits (Optional)
18.5 Tonnes (TQ & Rectangular 150 x 176mm)
25.0 Tonnes
( TP 150 x 210 / 14mm )
46817.5 Tonnes
(TQ & Round 6"/32mm)420 x 220 ISO 10 x M24 x 335 P 281 20" / 22.5' 8021
521
53025" / 26" 7689
420 x 220 5809
460 x 180 ISO 10 x M27 x 335 Q 281
ISO 10 x M24 x 335 P 281 20"/22.5'/24"
Axle Page 4
Low Bed Axles (8.0 - 15.0 Tonnes Capacity) With In-board drum.
Capacity Brake Wheel No. x Size of Brake Wheel Minimum Model Axle Weights(Bearing & Beam Size) Size Fixing Wheel Stud x PCD Type Bore Dia. Wheel Size Number Approximated.
(mm) (mm) (mm) Kg
8.0 Tonnes( TN & Round 5"/16mm )
311 x 127 ISO 10 x M22 x 225 P 176 15" 2954/10 315
311 x 178 176 15"/17.5" 9508 365
335 x 210 176 17.5" 9504 380
Notes:
1) 5" Round Axle - 16mm-19mm thick beam is standard for 10-13 Tonnes capacity.
2) 5" Round Axle - 25mm thick beam is standard for 15 Tonnes capacity.
3) Inboard brake drums are standard.
4) Twin tyre steel wheel fixings are standard. ISO single wheel fixings are also available.
5) Standard track length - 1850mm + Australia - 1890 & 1940mm - other track lengths are also available.
6) All axles include standard manual slack adjuster, auto slack adjuster is optional.
7) Bearing size/type : TQ Metric 90-100 Bearing, TM Metric 65-90 Bearing,TN Imperial 2.5/8" - 90 Bearing,
TP Parallel Imperial 89.6 Bearing, THU -Sealed Cartridge Bearing
8) All Axles are available with ABS ready Kits (Optional)
2783/10 31510 x M22 x 225 P
12.0 Tonnes (TM & Round 5"/16mm)
335 x 210 ISO 10 x M22 x 225
10 x M22 x 225
10.0 Tonnes(TN & Round 5"/16mm)
311 x 178 ISO
311 x 178 ISO
ISO15.0 Tonnes
(TM & Round 5"/25mm)
10 x M22 x 225 P 176
P
13.0 Tonnes(TN & Round 5"/19mm)
10 x M22 x 225
311 x 178 ISO
2950/10 330P 176
31515"/17.5" 9511
9501 315P 176
15"/17.5"176
15"/17.5"
17.5"
Axle Page 5
Disc Brake Axles (10-12 Tonnes Capacity)
Capacity Axle Weights
(Bearing & Beam Size) Approximated.
Kg
281 2980/3 320
220 2980/2 315
221 19.5" 2980/7 315
281 2970/3 320
220 2970/2 315
220 2570 350
281 2571 355
12.0 Tonnes ( TP & Round 5"/16mm )
Ø430 ISO 281 20" / 22.5" 2928 342
1) 5" Round Axle - 16mm standard wall thickness, 19mm optional wall thickness.
2) Twin tyre steel wheel fixings are standard. ISO single wheel and twin tyre aluminum wheel fixings are also available.
3) Standard track length - 1850mm, other track lengths are also available.
4) All axles include standard manual slack adjuster, auto slack adjuster is optional.
5) Bearing size/type : TQ Metric 90-100 Bearing, TM Metric 65-90 Bearing,TN Imperial 2,5/8" - 90 Bearing,
TP parallel Imperial 89.6 bearing, THU -Sealed Cartridge Bearing
6) All Axles are available with ABS ready Kits (Optional)
Minimum Wheel Size
Model Number
10.0 Tonnes (TN & Round 5"/16mm)
10 x M22 x 285.75
10 x M22 x 285.75
Wheel Bore Dia
( mm)
20" / 22.5"
RotorSize
( mm ) Fixing
No. x Size of
Wheel Stud x PCD
11.0 Tonnes ( TN & Round 5' / 16mm )
(mm)
10 x M22 x 335
11.0 Tonnes MFL(THU & Round 5"/16mm)
Ø430 ISO
10 x M22 x 335
10 x M22 x 335
20" / 22.5"
Ø375 ISO
8 x M22 x 275
10 x M22 x 335
10 x M22 x 285.75
Ø430 ISO
20" / 22.5'
Axle Page 6
Unbraked Axles (12 -18 ton capacity)
ISO 10 x M22 x 335 281 2021U
JAP 8 x M20 x 285 221 2011U
ISO 10 x M22 x 225 178 15" 9501U
ISO 10 x M22 x 335 281 20" 5021U
ISO 10 x M22 x 335 281 20" 8002U
ISO 10 x M22 x 335 281 20" 5801U
ISO 10 x M24 x 335 281 20" 8021U
Notes:
1) 5" Round Axle - 16mm -32mm standard wall thickness, 6" Square beams- 14mm is standard wall thickness.
2) Twin tyre steel wheel fixings are standard. ISO single wheel and twin tyre aluminum wheel fixings are also available.
3) Standard track length - 1850mm, other track lengths are also available.
4) Bearing size/type : TQ Metric 90-100 Bearing, TM Metric 65-90 Bearing,TN Imperial 2.5/8" - 90 Bearing,
TP Parallel Imperial 89.6 bearing, THU -Sealed Cartridge Bearing
17.5 Tonnes(TQ & Round 6"/32mm)
Model Number
203
223
152
Axle Weights Approximated.
Kg
175
165
152
210
Capacity (Bearing & Beam Size)
No. x Size of Wheel Stud x PCD
(mm)
Wheel Bore Dia.
( mm )
Wheel FixingMinimum
wheek Size
20"12.0 Tonnes(TM & Round 5"/16mm)
12.0 Tonnes(TM & Square 6"/14mm)
15.0 Tonnes(TQ & Round 5"/25mm)
16.0 Tonnes(TQ & Square 6"/14mm)
Axle Page 7
Self Steer Axles - Drum Brake
Capacity Brake Wheel No. x Size of Brake Wheel Minimum Model(Bearing & Beam Size) Size Fixing Wheel Stud x PCD Type Bore Dia. Wheel Size Number
(mm) (mm) (mm)
420 x 180 10 x M22 x 335 P 281 20"/22.5" SS2081 525
350 x 200 8 x M22 x 275 P 221 19.5" SS2082 512
310 x 190 10 x M22 x 225 P 176 15"/17.5" SS2083 505
Self Steer Axles - Disc Brake
Axle Capacity Wheel Minimum Model(Beam Size) Bore Dia. Wheel Size Number
(mm)
12.0 Tonnes( TN Round 5"/25mm )
Notes:
1) 5" Round Axle - 25mm standard wall thickness.
2) Twin tyre steel wheel fixings are standard. ISO single wheel and twin tyre aluminum wheel fixings are also available.
3) Standard track length - 1850mm, other track lengths are also available.
4) All axles include standard manual slack adjuster, auto slack adjuster is optional.
5) All Axles are available with ABS ready Kits (Optional)
12.0 Tonnes(TM & Round 5"/25mm )
Axle Weights Approximated.
Kg
Axle Weights Approximated.
Kg
518SS2091
ISO
281 20"/22.5"
WheelFixing
No. x Size ofWheel Stud x PCD
(mm)
ISO 10 x M22 x 335
Axle Page 8
Axles Rows of eight ( 8-10 capacity) with inboard brake drum.
Capacity Brake Wheel Brake Wheel Minimum Model
(Bearing & Beam Size) Size Fixing Type Bore Dia. Wheel Size Number
(mm) (mm) /Track Length
P
P
P
P 281
Notes:
1) 5" Round Axle - 16mm thick beam is standard for 8-10 Tonnes capacity.
2) Inboard brake drums are standard.
3) Twin tyre steel wheel fixings are standard. ISO single wheel fixings are also available.
4) Min track length - 750mm, other track lengths are also available.
5) All Axles are available with ABS ready Kits (Optional)
6) Bearing size/type : TM Metric 65-90 Bearing,TN Imperial 2.5/8" - 90 Bearing,
7) Pivot blocks is according to trailer applications & customer request.
`
8.0 Tonnes
(TN & Round 5" / 16mm )
10.0 Tonnes
(TN & Round 5" / 16mm )
12.0 Tonnes
(TM & 5" Round / 16mm )
20.0 Tonnes
(TQ & 6" Round/ 32mm )
420 x 220 ISO 10 x M22 x 335
420 x 220 ISO 10 x M22 x 335
311 x 178 10 x M22 x 225
10 x M22 x 335
ISO
ISO12.0 Tonnes
(TM & 5" Round/ 25mm )
311 x 178 ISO 10 x M22 x 225
420 x 180
311 x 178
311 x 127
P 281
276
792273/K0750
792284/K0750
789262 /
K0750
790498 /
K0750
789150 /
K0850
176
20" / 22.5' 789310 /
K0965
20" / 22.5' 789173 /
K0965
20" / 22.5'
176 15" / 17.5"
282
290
290
315
20" / 22.5'
176
281
Axle Weights
Approximated.
Kg
No. x Size of
Wheel Stud x PCD
(mm)
P 15" / 17.5"176
15" / 17.5"
ISO
ISO P
10 x M22 x 225
10 x M22 x 225792259/K0750
792287/K0750
260
276
L
Axle Page 9
Spider/Spoke Axles (10.5 - 17.5 Tonnes Capacity ) Inboard Drum Axles.
Brake Wheel Brake Minimum ModelSize Fixing Type Wheel Size Number
(mm)
335 x 210 2950/1 316
311 x 178 2783/1 298
420 x 220 Spoke Q 20" 2782/1 341
420 x 220 Spoke Q 20"78792279
/R/ELS360
420 x 220Europe Spoke
P 24' 6862 405
420 x 220Europe Spoke
P 24" 8017 456
Notes:
1) 5" Round Axle - 16mm standard wall thickness, 19mm -25mm optional wall thickness.
2) Twin tyre steel wheel fixings are standard. ( Trilex Wheel Rims)
3) Standard track length - 1850mm, other track lengths are also available.
4) All axles include standard manual slack adjuster, auto slack adjuster is optional.
5) Bearing size/type : TQ Metric 90-100 Bearing, TM Metric 65-90 Bearing,TN Imperial 2,5/8" - 90 Bearing,
TP Parallel imperial 89.6 Bearing, THU -Sealed Cartridge Bearing
6) All Axles are available with ABS ready Kits (Optional)
20"
Axle Weights Approximated.
Kg
No. x Size ofWheel Stud x PCD
(mm)
3 - Spoke 15"
78792158/R/ELS
320
6062P
2682/1
385
380
20"
15" / 17.5"
24"
Spoke
Spoke
12.0 Tonnes (TN & Round 5"/16mm)
P
6 Spoke - 24"
420 x 180 Spoke 5-Spoke 20" Q
P
Trilex 6 Spoke - 24"
5 Spoke 20"
16.0 Tonnes (TQ & Square 6"/14mm)
Capacity(Bearing & Beam Size)
10.5 Tonnes(TN & Round 5'/16mm)
17.5 Tonnes (TQ & Round 6"/32mm)
5-Spoke 20"
12.0 Tonnes(TM & Square 6"/14mm)
12.0 Tonnes(TP & Round 5"/16mm)
6 Spoke - 24"
420 x 220 Spoke
420 x 18013.0 Tonnes
(TP & Round 5"/19mm)
5 Spoke 20"
Axle Page 10
Axles With Preset Hub (Aluminum) 12.0 Tonnes Capacity
Brake Wheel Wheel Minimum Model WeightSize Fixing Bore Dia. Wheel Size Number Approx.
(mm) (mm)
420 x 180 281 20"/22.5" 2782/12P 305
420 x 180 ISO 220 20"/22.5" 2782/4P 295
335 x 210 221 19.5" 2950/8P 285
Centrifuse Light Weight Brake Drum Available on Request
Brake Drum 10 x 285PCD - O/B Part No. 787886 Centrifuse Brake drum 89996BX
8 x M22 x 275
Axle Capacity& Bearing
12.0 Tonnes (TN & Round 5"/16mm)
No. x Size ofWheel Stud x PCD
(mm)
10 x M22 x 335
10 x M22 x 285.75
Alumimum Preset Hub only Weight : 16kg/hub( Approx. 10Kg/Hub lighter than Steel Casting )
Centrifuse Brake Drum Weight : 37kg/Drum( Approx. 8Kg /Drum lighter than Standard : Steel Casting
Axle Page 11
Slack Adjusters
Manual Slack Adjuster (All Brake Size)
Part Number : 730101/3
Spline : SAE 10
Arm Length : 5", 6" and 7" (127, 152 and 176mm)
Clevis Pin Size : Ø1/2" (12.7mm)
Auto Slack Adjuster (HD, All Brake Size)
Part Number : 730104/5 730105/5
Spline : SAE 10 SAE 37
Arm Length : 5", 6" & 8" 5", 6" & 8"
Clevis Pin Size : Ø14mm Ø14mm
Auto Slack Adjuster (BD)
Part Number : YB21153 (Dia. 311 & 335mm brake)
Spline : SAE 10
Arm Length : 5" and 6" (127 and 152mm)
Clevis Pin Size : Ø1/2" (12.7mm)
Part Number : YB21102 (Dia. 420mm brake)
Spline : SAE 10
Arm Length : 5" and 6" (127 and 152mm)
Clevis Pin Size : Ø1/2" (12.7mm)
Axle Page 12
YTE 75 Mechanical Suspension ‐ Overslung Series ( 8‐10 Leaf Spring ‐ 12 ton per Axle)
Leafspring Axle 5" Round 5" Round 6" Square 6" Square
Capacity per Axle Spacing Beam Beam Beam Beam
(mm) 25mm Spring Seat 50mm Spring Seat 25mm Spring Seat 50mm Spring Seat
8 Leaf Spring / 12 ton B911001/01 B911001/02 B911006/01 B911006/02
10 Leaf Spring / 15 ton B911011/01 B911011/02 B911016/01 B911016/02
8 Leaf Spring / 12 ton B912003/01 B912003/02 B912008/01 B912008/02
9 Leaf Spring / 12 ton B912003/9/01 B912003/9/02 B912008/9/01 B912008/9/02
10 Leaf Spring / 15 ton B912013/01 B912013/02 B912018/01 B912018/02
8 Leaf Spring / 12 ton B912005/01 B912005/02 B912010/01 B912010/02
10 Leaf Spring / 15 ton B912015/01 B912015/02 B912020/01 B912020/02
8 Leaf Spring / 12 ton B913003/01 B913003/02 B913008/01 B913008/02
9 Leaf Spring / 12 ton B913003/9/01 B913003/9/02 B913008/9/01 B913008/9/02
10 Leaf Spring / 15 ton B913013/01 B913013/02 B913018/01 B913018/02
8 Leaf Spring / 12 ton B913005/01 B913005/02 B913010/01 B913010/02
10 Leaf Spring / 15 ton B913015/01 B913015/02 B913020/01 B913020/02
Standard Kits are with Rubber Bush for Torque arm & Equalizer Assembly
Also Available Poly Bush for Torque Arm & Equalizer Assebly
Tridem ‐ Axle Suspension (1360mm Axle cen. Spacing) (Approximated Weight = 596kg ‐ 8 Leaf)
Tandem Axle Suspension (1538mm Axle cen. Spacing)(Approximated Weight 422kg ‐ 8Leaf)
Tandem Axle Suspension (1360mm Axle cen. Spacing)(Approximated Weight 405kg ‐ 8 Leaf)
Mounting height (mm)
Spring Seat 5" Round 6" SquareHeight Beam Beam
25 385 395
50 410 420
75 435 445
Single Axle Suspension. ( Approximated Weight 200kg ‐ 8 Leaf)
Dimensions (mm) Mounting hangers
AxleSpacing
1360 1118 1360 1360
1540 1207 1538 1538
Kit Number
'A' 'B' C'
Tridem
1,538
1,360
Axle Type
Tandem
1,538
1,360
Single -
438
438
Mech Suspension Page 1
YTE75 Mechanical Suspension ‐ Underslung Series. (8‐10 leaf ‐12ton cap. Axle)
Leafspring Axle
Capacity per Axle Spacing
(mm)
8 Leaf Spring / 12 ton
10 Leaf Spring / 15 ton
8 Leaf Spring / 12 ton
9 Leaf Spring / 12 ton
10 Leaf Spring / 15 ton
8 Leaf Spring / 12 ton
10 Leaf Spring / 15 ton
8 Leaf Spring / 12 ton
9 Leaf Spring / 12 ton
10 Leaf Spring / 15 ton
8 Leaf Spring / 12 ton
10 Leaf Spring / 15 ton
Standard Kits are with Rubber Bush for Torque arm & Equalizer Assembly
Also Available Poly Bush for Torque Arm & Equalizer Assembly
Tri‐Axle Suspension (1360mm Spacing ) (Approximated Weight 668kg ‐ 8 Leaf)
Tandem Axle Suspension (1538mm Spacing) (Approximated Weight 435kg ‐ 8 Leaf)
Tandem Axle Suspension (1360mm Spacing) (Approximated Weight 418kg ‐ 8 Leaf)
Mounting height (mm)
Spring Seat 5" Round 6" SquareHeight Beam Beam
25 200 190
50 200 190
75 200 190
Single Axle Suspension (Approximated Weight 230kg ‐ 8 Leaf)
Dimensions (mm)
Axle 'A' 'B' 'C'Spacing
1360 1162 1360 1360
1538 1239 1538 1538
Kit Number
B916010
B916020
B916018
B916008/9
B914006
B915008/9
B915008
B912020
B915010
B914016
5" RoundBeam
25mm Spring Seat
6" SquareBeam
25mm Spring Seat
B916008
B915018
Single
B916003/9
-
Axle Type
1,360
Tandem
1,538
1,360
B914001
B914011
B915005
B915015
B915003
B915003/9
B915013
1,538
Tridem
B916003
B916013
B916005
B916015
470
470
470
470
Mech Suspension Page 2
YTE75/90 Mechanical Suspension ‐ Overslung Series ( 10 leaf ‐ 15 Ton Cap. Per Axle)
Axle Type Axle
Single .
1,300
1,540
1,300
1,540
Quad 1,300
Quad Axles Suspension (1300mm Spacing) (Approximated Weight 1095kg ‐ 10 Leaf)
Tri‐Axle Suspension (1300mm; 1540mm Spacing) (Approximated Weight 820kg ‐ 10 Leaf)
Tandem Axle Suspension (1300mm; 1540mm Spacing) ( Approximated Weight 525kg ‐ 10 Leaf)
Dimensions (mm)
'F' 'R' 'H' 'F' 'R' 'H'
1,300 1,088 1,300 1,300 395 525 475 380 525 485
1,540 1,208 1,540 1,540 395 620 475 380 620 485
Kit Number
25mm Spring Seat
'A' 'B' 'C'5" Round
B919014
B919044
B919040
B919019
B919045
B919042
Standard -Bronze Bush - Optional Vesconite Bush for low maintenance available.
Axle Spacing
6" Square
Tridem
6" SquareBeam
B919012
B919031
B919016
B919017
B919032
5" RoundBeam
25mm Spring Seat
B919011
Tandem
Spacing ( mm)
Mech Suspension Page 3
YTE75/90 Mechanical Suspension ‐ Underslung Series (10 leaf ‐ 15 ton Cap. Per Axle)
Axle Type
Single
Quad
Standard -Bronze Bush - Optional Vesconite Bush for low maintenance available.
Quad Axle Suspension (1300 mm Spacing) (Approximated Weight 1145kg ‐ 10 Leaf)
Tri‐Axle Suspension (1300mm;1540mmmm) ( Approximated Weight 848kg ‐ 10 leaf)
Tandem Axle Suspension (1300mm; 1540mm) (Approximated Weight 548kg ‐ 10 Leaf)
Dim "P" Packer fitted to all suspension hangers as
shown , packers are not supplied as part of
the suspension kit.
Dimensions (mm)
Axle 5" Round 6" SquareSpacing 'F' 'R' 'H' 'F' 'R' 'H'
1,300 1,088 1,300 1,300 370 495 270 370 495 260
1,540 1,208 1,540 1,540 370 605 270 370 605 260
1,540
1,300
-
1,300
1,540
1,300
'B' 'C''A'
B919041 B919043
5" RoundBeam
25mm Spring Seat
B919021
B919022Tandem
Tridem
Kit Number
B919026
B919033
B919024
B919046
B919027
B910034
B919029
B919047
6" SquareBeam
25mm Spring Seat
AxleSpacing mm
Mech Suspension Page 4
YTE90 Mechanical Suspension ‐ Overslung Series (10 leaf spring ‐ 18 ton Cap. Per Axle)
Single
Standard : Bronze Bush- Optional Vesconite Bush for low maintenance available
Quad Axle Suspension (1300mm ; 1540mm Spacing) (Approximated Weight 1290kg)
Tri‐Axle Suspension (1300mm; 1540mm; Spacing)(Approximated Weight 970kg)
Tandem Axle Suspension (1300mm; 1540mm Spacing) (Approximated Weight 660kg)
Optional U Bolt Mounting is also available Dimensions ( mm)
Axle 6" Round 6" SquareSpacing 'F' 'R' 'H' 'F' 'R' 'H'
1,300 1,088 1,300 1,300 380 525 485 380 525 485
1,540 1,208 1,540 1,540 380 620 485 380 620 485
.
1,300
1,540
1,300
B920053
Quad-Axle
B920043
B920067
B920044
B920069
B920027
1,540
1,300
1,540
Tandem
Tri-Axle
25mm Spring Seat
B920041
B920061
25mm Spring Seat
B920005
B920013
'A' 'B' 'C'
B920021
B920054
B920222
B920025
Kit Number
Axle Type6" Square
Beam6" Round
BeamAxle
Spacing (mm)
Mech Suspension Page 5
YTE90 Mechanical Suspension ‐ Underslung Series (10 leaf spring ‐ 18 ton Cap. Per Axle)
Axle Type
Single
Standard : Bronze Bush- Optional Vesconite Bush for low maintenance available
Quad Axle Suspension ( 1300mm; 1540mm spacing) (Approximated Weight 1300kg)
Tri‐Axle Suspension (1300mm; 1540mm; Spacing) (Approximated Weight 995kg)
Tandem Axle Suspension (1300mm; 1540mm Spacing) (Approximated Weight 655kg)
Dim "P" Packer fitted to all suspension hangers as
shown , packers are not supplied as part of
the suspension kit.
Dimension (mm)
Axle 6" Round 6" SquareSpacing 'F' 'R' 'H' 'F' 'R' 'H'
1,300 1,088 1,300 1,300 370 495 260 370 495 260
1,540 1,208 1,540 1,540 370 605 260 370 605 260
B920059
B920066
B920060
Kit NumberAxle
Spacing (mm)
1,300
B920049
B920058
6" RoundBeam
6" SquareBeam
B920047
B920223
B920024
'A' 'B' 'C'
1,3001,540 B920063
Tandem
Tridem
Quad
B920062
B920045
B920065
B920046
B920070
1,300
1,540
1,540
Mech Suspension Page 6
YTE115 Mechanical Suspension ‐ Overslung Series ( 8 leaf spring ‐ 25 ton Cap. Per Axle)
TandemTridemQuad
Quad Axle Suspension ( 1540mm spacing) (Approximated Weight 2350kg)
Tri‐Axle Suspension (1540mm; Spacing) (Approximated Weight 1850kg)
Tandem Axle Suspension ( 1540mm Spacing) (Approximated Weight 1300kg)
Dimension (mm)Axle Rectangular
Spacing 'F' 'R' 'H'1,540 1,305 1,540 1,540 600 600 500
MG4C-V08G
Kit NumberRectangular Beam
150 x 210 mmMG2C-V08GMG3C-V08G
Axle Type
'A' 'B' 'C'
6" Square Beam150 x 150 mm#MG2C-V08S#MG3C-V08S#MG4C-V08S
AxleSpacing (mm)
1,5401,5401,540
Mech Suspension Page 7
YTE75 FB , Fabricated Mechanical Suspension ‐ Overslung Series ( 9 leaf spring ‐ 12 ton Cap. Per Axle)
AxleSpacing (mm)
Single 1,360
Tandem 1,360
Tridem 1,360
Options of 9 leafs and 10 leafs is also available upon request
Tri‐Axle Suspension (1360mm; Spacing)
Tandem Axle Suspension ( 1360mm Spacing)
Single Axle Suspension.
MR3E-V09S
Kit Number
9 Leaf Spring / 12 ton
9 Leaf Spring / 12 ton
MG1C-V09S
Axle TypeRectangular
Beam
MG2C-V09S
MG3C-V09S
Leafspring
Capacity per Axle
9 Leaf Spring / 12 ton
6" SquareBeam
MR1E-V09S
MR2E-V09S
Mech Suspension Page 8
YTE 75 Mechanical Suspension ‐ Overslung Series ( 3 Leaf Spring ‐ 12 ton per Axle)
5" Round 6" SquareBeam Beam
25mm Spring Seat 25mm Spring Seat
Single MS1E-V03R MS1E-V03S
Tandem MS2E-V03R MS2E-V03S
Tri-Axle MS3E-V03R MS3E-V03S
Tridem ‐ Axle Suspension (1360mm Axle cen. Spacing)
Tandem Axle Suspension (1360mm Axle cen. Spacing)
Single Axle Suspension.
Axle Type
Leafspring
Capacity per Axle
3 Leaf Spring / 12 ton
AxleSpacing
(mm)
-
Kit Number
3 Leaf Spring / 12 ton
3 Leaf Spring / 12 ton
1,360
1,360
Mech Suspension Page 9
YTE 75 Mechanical Suspension - Underslung Series ( 3 Leaf Spring - 12 ton per Axle)
5" Round 6" SquareBeam Beam
25mm Spring Seat 25mm Spring Seat
Single MS1E-U03R MS1E-U03S
Tandem MS2E-U03R MS2E-U03S
Tri-Axle MS3E-U03R MS3E-U03S
Tridem ‐ Axle Suspension (1360mm Axle cen. Spacing)
Tandem Axle Suspension (1360mm Axle cen. Spacing)
Single Axle Suspension.
1,360
Kit Number
Axle Type
Leafspring
Capacity per Axle
3 Leaf Spring / 12 ton
3 Leaf Spring / 12 ton
3 Leaf Spring / 12 ton
AxleSpacing
(mm)
-
1,360
Mech Suspension Page 10
MT75 SUSPENSION CODES - Australia .
MODEL SUSPENSION SUSPENSION MOUNTING SPRING AXLE SPECIAL
TYPE SPREAD TYPE HEIGHT TYPE CLAMP GROUP FEATURES
MT SP T H S C F
MT 3A O 370 8 R
SP = P/N REF T = H = S = C =
1A - SINGLE AXLE 581### O - OVERSLUNG OVERSLUNG SUSPENSION 8 - 8 LEAF 13x75mm R - 127mm dia axle
2A - TANDEM 1232mm 582###A U - UNDERSLUNG 370mm - R127 8 LEAF LOW SEAT 9 - 9 LEAF 13x75mm S120 - 120mm sqr axle
2B - TANDEM 1384mm 582###B 425mm - R127 8 LEAF HIGH SEAT 10H - 10 LEAF 16x75mm S150 - 150mm sqr axle
2C - TANDEM 1538mm 582###C 370mm - S120 8 LEAF LOW SEAT 3H - 3 LEAF 25x75mm
3A - TRI AXLE 1232mm 583###A 425mm - S120 8 LEAF HIGH SEAT
3B - TRI AXLE 1384mm 583###B 385mm - S150 8 LEAF LOW SEAT
3C - TRI AXLE 1538mm 583###C 385mm - R127 9 LEAF LOW SEAT F =
4A - QUAD AXLE 1232mm 584###A 440mm - R127 9 LEAF HIGH SEAT Blank - NO FEATURE
4B - QUAD AXLE 1384mm 584###B 385mm - S120 9 LEAF LOW SEAT DB - DRAWBAR FRONT HANGER
4C - QUAD AXLE 1538mm 584###C 440mm - S120 9 LEAF HIGH SEAT 4.8.4 - QUAD LINK 1232/2464/1232 SPREAD
400mm - S150 9 LEAF LOW SEAT (FOR BOTH OVERSLUNG & UNDERSLUNG)
430mm - R127 10H LEAF LOW SEAT
485mm - R127 10H LEAF HIGH SEAT
430mm - S120 10H LEAF LOW SEAT ADD-ON DRAWBAR KITS AVAILABLE:
485mm - S120 10H LEAF HIGH SEAT 58DBK1 - c/w CHEEK PLATES (59900039)
450mm - S150 10H LEAF LOW SEAT 58DBK2 - c/w DRAWBAR END HOUSING (59900096)
450mm - S150 13H LEAF LOW SEAT 58DBK3 - c/w DRAWBAR END HOUSING/END PIVOT
355mm - R127 3H LEAF LOW SEAT CASTING (59900096/59900097)
410mm - R127 3H LEAF HIGH SEAT
355mm - S120 3H LEAF LOW SEAT
410mm - S120 3H LEAF HIGH SEAT
370mm - S150 3H LEAF LOW SEAT
UNDERSLUNG SUSPENSION
200mm - 8 & 9 LEAF LOW SEAT
210mm - 10H & 3H LEAF LOW SEAT
PACKED OVERSLUNG SUSPENSION
MT Suspension Page 1
YTE 75 Mechanical Suspension MT - Overslung Series. 10.0 – 27.90 TONNE CAPACITY PER SUSPENSION KIT MODEL
TRI-AXLE SUSPENSIONAXLE SPACING 1232mm ( 8'1") and 1364mm ( 9'1")
ADR NO'S 6305SS AND 9074SS
APPROX WEIGHT 585KG ‐ 8 Leafs
TRI-AXLE SUSPENSIONAXLE SPACING 1538mm ( 10'1")
ADR NO'S 6305SS and 9074SS
APPROX WEIGHT 645KG ‐ 8 Leafs
TAN-AXLE SUSPENSION SINGLE AXLE SUSPENSIONAXLE SPACING 1232MM ( 4'0") , 1384mm (4'6") and 1538mm ( 5'0") ADR NO'S 6306SS and 6224S
ADR NO'S 6307SS and 9076SS APPROX WEIGHT 185KG ‐ 8 Leafs
APPROX WEIGHT 385KG ‐ 8 Leafs
SUSPENSION MOUNTING HEIGHT SUSPENSION DIMENSION
Axle Seat Dimension8
Leafs
9
Leafs
10
Leasfs13 Leafs
3
leafs
Axle Spread
(mm) Model
Dim A
(mm)
Dim B
(mm)
Dim C
(mm)
Low F‐M‐R 370 385 430 430 355 1232 (4'0") MT2A or MT3A 1054 1232 1232
High F‐M‐R 425 440 485 485 410 1384 (4'6") MT2B or MT3B 1130 1384 1384
1538 (5'0") MT2C or MT3C 1207 1538 1538
unladen condition
MT Suspenion Page 2
YTE 75 Mechanical Suspension MT - Underslung Series. 10.0 – 28.66 TONNE CAPACITY PER SUSPENSION KIT MODEL
TRI-AXLE SUSPENSIONAXLE SPACING 1232mm ( 8'1") and 1364mm ( 8'1")
ADR NO'S 9075SS and 9130SS
APPROX WEIGHT 610KG ‐ 8 Leafs CAPACITY : 28.66 Tonnes
TRI-AXLE SUSPENSIONAXLE SPACING 1348mm ( 9'1") and 1538mm ( 10'1")
ADR NO'S 9075SS and 9130S
APPROX WEIGHT 640KG ‐ 8 Leafs CAPACITY : 28.66 Tonnes
TAN-AXLE SUSPENSION SINGLE AXLE SUSPENSIONAXLE SPACING 1232mm ( 4'0"), 1384mm (4'6") and 1538 ( 5'0") ADR NO's 6223SS and 6360SS
ADR NO'S 9073SS AND 9132SS APPROX WEIGHT 190KG ‐ 8 Leafs
APPROX WEIGHT 400KG ‐ 8 LEAFS CAPACITY : 20.00Tonnes CAPACITY 10 Tonnes
SUSPENSION DIMENSION
Dim A
(mm)
Dim B
(mm)
Dim C
(mm)
1086 1232 1060
1162 1384 1135
1239 1538 1210
unladen condition
Notes :
1 ) 200mm ride height all models
2) Mounting height with 3 leafs springs = 200mm
( all axle spacing )
Axle Spread (mm)
1232 (4'0")
1384 (4'6")
1538 (5'0")
Model
MT2A or MT3A
MT2B or MT3B
MT2C or MT3C
MT Suspenion Page 3
18-22 Ton Capacity Mechanical Suspension. ( Over slung) 18.0 – 22.0 TONNE CAPACITY
QUAD-AXLE SUSPENSIONAXLE SPACINGS 1300mm and 1550mm
ADR NO 12219SS
TRI-AXLE SUSPENSIONAXLE SPACINGS 1300mm and 1550mm
ADR NO 12218SS
TANDEM AXLE SUSPENSIONAXLE SPACINGS 1300mm and 1550mm
ADR NO 12217SS
A
(mm)
B
(mm)
C
(mm)
D
(mm)
F
(mm)
R
(mm)
H1
(mm)
H2
(mm)
H3
(mm)
H4
(mm)
1058 1300 1300 1080 395 525 500 515 540 540
1183 1550 1550 1205 395 645 500 515 540 540
unladen condition
ModelAxle Spacing
(mm)
YTB2D/YTB3D/YTB4D
YTB2C/YTB3C/YTB4C
1300 Nominal
1550 Nominal
MT Suspenion Page 4
18-22 Ton Capacity Mechanical Suspension. ( Under slung) 18.0 – 22.0 TONNE CAPACITY PER AXLE
QUAD-AXLE SUSPENSIONAXLE SPACINGS 1300mm and 1550mm
ADR NO 12219SS
TRI-AXLE SUSPENSIONAXLE SPACINGS 1300mm and 1550mm
ADR NO 12218SS
TANDEM AXLE SUSPENSIONAXLE SPACINGS 1300mm and 1550mm
ADR NO 12217SS
A
(mm)
B
(mm)
C
(mm)
D
(mm)
F
(mm)
R
(mm)
H1
(mm)P (mm)
1058 1300 1300 1080 380 510 275 140
1183 1550 1550 1205 380 630 275 140
unladen condition
Model Axle Spacing (mm)
YTB2D/YTB3D/YTB4D 1300 Nominal
YTB2C/YTB3C/YTB4C 1550 Nominal
MT Suspenion Page 5
TECAIR 1 - Air Suspension Modules 11- 12 ton Cap.
Capacity
Standard Spring Center Single Axles 8163SS
Standard Airbag Center Tandem Axle 8164SS
Tri-Axle 8162SS
Quad Axle 12567SS
UNDERSLUNG 127MM ROUND BEAM 200 HEIGHT UNDERSLUNG 127MM ROUND BEAM 400MM HEIGHT
INTEGRATED AXLE LIFT UNDERSLUNG 150MM SQUARE BEAMS
Air Suspension for Round Axles Air Suspension for Square Axles
Ride Height Axle without Ride Height Axle without
(mm) Lift (mm) Lift
200 TA111U200RS0000 200 TA111U200SS0000
400 TA111U200RS0000 400 TA111U400SS0000
Add TAL-E1-00 for Lift Add TAL-E1-00 for Lift
200mm Ride Height Model - 210kg
Standard Ride Height200mm and 400mm.
400mm Ride Height Model - 228kg
Integrated Side Lift - 58kg
Tare Weights
(Approximate)
12 Tonnes Per Module
Tec Air 1 & 2 Approved ADR no'sOther ride heights available upon request
960mm @ 1,850mm Axle Track Length
800mm @ 1,850mm Axle Track Length
STANDARD RIDE HEIGHT
Air Suspension Page 1
Air Suspension for Round Axles Air Suspension for Square Axles
Add TAL-E1-00 for Lift
TARE WEIGHT APPROX 210KG ( Ride Height 200mm)
NEW BOLT ON AXLE LIFT TAL-E1
Tec Air 1 Air Suspension Tec Air 2 Air Suspension Tec Air Z 9 ton Air Suspension
Air Suspension with New Bolt On Axle Lift
1 Common Axle Lift - suitable for All York Models Tec Air Suspensions 2 Easy installation with a one bolt mounting . 3 Low Maintenance - easy replacement of Air Lift Air bellow. 4 Ease of wearing sleeve / roller replacement. 5 TAL - E1 - allows quick lifting and lowering of axle. 6 Long lasting air bellow - double bellow type.
TA111U300RD0000
Under Slung Ride
Height (mm)
Susp. Without Lift -
Model Number
Under Slung Ride
Height (mm)
Susp. Without Lift -
Model Number
250
280
330
Over Slung Ride
Height (mm)
Susp. Without Lift -
Model Number
450 TA111U450RS0000
TA111U300RS0000
350 TA111U350RS0000
300
380
480
500 TA111V500RS0000
600 TA111V600RS0000
TA111U250SS0000
TA111U330SS0000
TA111U480SS0000
TA111U280SS0000
TA111U380SS0000
OPTIONAL RIDE HEIGHT
Air Suspension Page 2
TECAIR 2 - Air Suspension Modules 9- 10 ton Cap.
Single Axles 8163SS
Tandem Axle 8164SS
Tri-Axle 8162SS
5" Round Beam
UNDERSLUNG OVERSLUNG
Ride Height Axle without Ride Height Axle without
(mm) Lift (mm) Lift
235 TA209U235RS0000 420 TA209V420RS0000
260 TA209U260RS0000 445 TA209V445RS0000
TA209U285RS0000 470 TA209V470RS0000
TA209U285RD0000 DISC BRAKE 495 TA209V495RS0000
310 TA209U310RS0000 520 TA209V520RS0000
TA209U335RD0000 DISC BRAKE 545 TA209V545RS0000
TA209U335RS0000 600 TA209V600RS0000
360 TA209U260RS0000
Add TAL-E1-00 for Lift
6" Square Beam
UNDERSLUNG OVERSLUNG
Ride Height Axle without Ride Height Axle without
(mm) Lift (mm) Lift
205 TA209U205SS0000 425 TA209U425SS0000
230 TA209U230SS0000 450 TA209U450SS0000
255 TA209U255SS0000 475 TA209U475SS0000
280 TA209U280SS0000 500 TA209U500SS0000
305 TA209U305SS0000 525 TA209U525SS0000
330 TA209U330SS0000 550 TA209U550SS0000
600 TA209U600SS0000
Add TAL-E1-00 for Lift
Tec Air 1 & 2 Approved ADR no's
UNDERSLUNG OVERSLUNG
285
335
CAPACITY
STANDARD SRPING CENTER
STANDARD AIR BAG CENTER
9.0 T onnes per module
960mm @1850 Axles Track Length
818mm @ 1850 Track Length
Air Suspension Page 3
TEC AIR Z ‐ 9 TON AIR SUSPENSION WITH 5' ROUND BEAM .
Standard Spring Centre 960mm @ 1850 Axle Track Length 1400NmStandard Air Bag Center 860mm @ 1850 Axle Track Length 250Nm
70Nm
35Nm
820Nm
Under slung Ride
Height
Susp. without Lift
– Model Number
Susp. with Bolt on Axle
Lift
– Model Number
170 TAZ‐09U170RS TAZ‐09U170RS 00E1
200 TAZ‐09U200RS TAZ‐09U200RS 00E1
225 TAZ‐0U225RS TAZ‐09U225RS 00E1
Over slung Ride
Height
Susp. without Lift
– Model Number
Susp. with Bolt on Axle
Lift
– Model Number
350 TAZ‐09V350RS TAZ‐09V350RS 00E1
375 TAZ‐09V357RS TAZ‐09V357RS 00E1
400 TAZ‐09V400RS TAZ‐09V400RS 00E1
Technical Information:
U BOLT ITEM 6
Capacity 9.0 Tonnes per module TORQUE SETTINGSPIVOT BOLTDAMPER BOLTSAIRSPRING MOUNTING BOLTS
AIRSPRING TOP PLATE STUDS
Pivot bush has a metal inner sleeve and bonded to outer rubber
with free floating anchor point for spring. Pivot bolt subjected to pure tensile load and all shear and shock
load absorbed by bush.Pivot rubber bush configured for good resilience and shock proof performance. The Parabolic spring as the trailing arm has smooth suspension
performance and excellent roll stiffness characteristics. Durable Shock absorber incorporating high damping
characteristic and friendly compliance. Reinforced structural steel weldable hanger with narrow
topflange to suit all chassis arrangements. Designed for user friendly installation with structural rigidity.
Fully fledged air lifting system with improved ground clearance.Bolt on Air side lift for ease of installation and serviceability. Low compact weight .
Proven spring seating arrangement for easy shock absorber fitment and spring clamping. Reliable Air spring performance for enhanced stability. Compact installation arrangement
Ease of wheel alignment process to cater 20mm axial adjustment
Air Suspension Page 4
Duratrac Air Suspension Under and Overslung ( Fix welded beam mounting)
Capacity 9-10 Tonnes Per Module
See Charts Below 60791162/07 1 Axle Auto Centre Lift
Other ride height available on request 60791162/08 2 Axles Auto Centre Lift
Axle Seat Suits 127mm diameter round beam 60791166/07 1 Axle Auto hanger Lift
60791166/08 2 Axles Auto hanger Lift
Axle Lift, Pneumatic Kits, Dump Kit,
Options Raise/Lower/Hold, Pressure Retention Kit, Standard Option
Axle Load Indicator Kit Single Axles 816355 8219SS
Tandem Axle 816455 8220SS
Tri-Axle 816255 8221SS
Part No. Description:TAD09V360RS0000 360mm Ride Height Overslung
TAD09V380RS0000 380mm Ride Height Overslung
TAD09V420RS0000 420mm Ride Height Overslung
TAD09V460RS0000 460mm Ride Height Overslung
Part No. Description:
TAD09U220RS0000 220mm Ride Height Underslung (Drum)
TAD09U240RS0000 240mm Ride Height Underslung (Drum)
TAD09U260RD0000 260mm Ride Height Underslung (Disc)
TAD09U260RS0000 260mm Ride Height Underslung (Drum)
TAD09U300RD0000 300mm Ride Height Underslung (Disc)
TAD09U300RS0000 300mm Ride Height Underslung
TAD09U340RS0000 340mm Ride Height Underslung
Note:
Hanger Size shown not applicable to all Riding Heights.
1) Duratrac Air Suspension - 5" Round Axle Beam .
2) Standard spring center and air bag center are for axles with 1,850 track length and tyre size 10.00R20
or 11.00R22.5. Other axle track length or bigger tyre size will affect spring center and air bag center.
3) All axles fitted are with long camshaft.
OVER SLUNG
UNDER SLUNG
Standard Ride Height
Axle Lift Kits
Duratrac Approved ADR no's
Tare Weight
(Without Lift)Approx. 120kg Dependent on ride height
` Air Suspension Page 5
Dreadnought 20 to 40 tonnes Low Mounting Tandem Bogie DN7 Low Mount
Axle Beam Capacity Capacity Track (T) Axle Spacing (A) Model@ Axle Capacity @ 80km/h @ 60km/h Spring ( C) Height (H) Number
(Highway) (Off Road) Stool (B) Height (H1)
5" Round @ 12.0 Tonnes 24.0 Tonnes 20.0 Tonnes 1850/900/580 1430/245/510 DN7/MK2/0900
6" Square @ 12.0 Tonnes 24.0 Tonnes 20.0 Tonnes 1850/900/580 1410/265/530 DN7S/MK2/0900
5" Round @ 15.0 Tonnes 30.0 Tonnes 24.0 Tonnes 1850/900/580 1430/245/510 DN7/MK2/0900
6" Square @ 16.0 Tonnes 30.0 Tonnes 24.0 Tonnes 1850/900/580 1410/265/530 DN7S/MK2/0900
( Unladen )
DN8 Low MountAxle Beam Capacity Capacity Track (T) Axle Spacing (A) Model
@ Axle Capacity @ 80km/h @ 60km/h Spring ( C) Height (H) Number
(Highway) (Off Road) Stool (B) Height (H1)
6" Square @ 16.0 Tonnes 32.0 Tonnes 28.0 Tonnes 1850/880/490 1490/260/465 DN8S/880
6" Round @ 17.5 Tonnes 35.0 Tonnes 32.0 Tonnes 1850/880/490 1490/260/468 DN8/880
6" Round @ 20.0 Tonnes 40.0 Tonnes 32.0 Tonnes 1850/880/490 1490/260/468 DN8/880
( Unladen )
DN7 Low Mount
Approximated Weight 748kg
Excluding Axle Weights.
Other Track Lengths
Available on Request
DN8 Low Mount
Approximated Weight 1075kg
Excluding Axle Weights.
* Note: For other tyre size, please contact York.
DN Page 1
Dreadnought 20 to 40 tonnes High Mounting Tandem BogieDN7 High Mount
Axle Beam Capacity Capacity Track (T) Axle Spacing (A) Model
@ Axle Capacity @ 80km/h @ 60km/h Spring ( C) Height (H) Number
(Highway) (Off Road)
5" Round @ 12.0 Tonnes 24.0 Tonnes 20.0 Tonnes 1850/900 1490/606 DNH7 - Plus
6" Square @ 12.0 Tonnes 24.0 Tonnes 20.0 Tonnes 1850/880 1490/606 DNH7S - Plus
5" Round @ 15.0 Tonnes 30.0 Tonnes 24.0 Tonnes 1850/900 1490/606 DNH7 - Plus I
6" Square @ 16.0 Tonnes 30.0 Tonnes 26.0 Tonnes 1850/880 1490/606 DNH7S - Plus I
( Unladen )
DN8 High MountAxle Beam Capacity Capacity Track (T) Axle Spacing (A) Model
@ Axle Capacity @ 80km/h @ 60km/h Spring ( C) Height (H) Number
(Highway) (Off Road)
6" Square @ 16.0 Tonnes 32.0 Tonnes 28.0 Tonnes 1850-1950/880 1490/606 DNH8S/MK2/0880
6" Round @ 17.5 Tonnes 35.0 Tonnes 32.0 Tonnes 1850-1950/880 1490/609 DNH8/MK2/0880
6" Round @ 20.0 Tonnes 40.0 Tonnes 32.0 Tonnes 1850-1950/880 1490/609 DNH8/MK2/0880
( Unladen )
Note: DN Bogies with LONGER than the Standard Track as Specified - Available on Request .
DNH7 High Mount Approximated Weight 930kg
Excluding Axle Weights.
Other Track Lengths
Available on Request
DNH8 High Mount Approximated Weight 1140kg
Excluding Axle Weights.
* Note: For other tyre size, please contact York.
DN Page 2
Walking Beam Bogies Under-Overslung (24-40 tonnes Cap.)
WB Bogie Underslung
Capacity
@ 80 km/h
(Highway)
5" Round @ 12.0 Tonnes 10.00R20 Twin 24.0 Tonnes WBA001
6" Square @ 12.0 Tonnes 12.00R20 Twin 30.0 Tonnes WBA001
Standard Axle Spacing 1540mm
Note: Axle Spacing and Track length of axles and walking beams as per customers requirements.
WB Bogie Overslung
Capacity Capacity
@ 80 km/h @ 40 km/h
(Highway) (Off Road)
6 Round @ 17.5 Tonnes 12.00R24 Twin 35.0 Tonnes 32.0 Tonnes WBA-RB2MK2
6 Round @ 20.0 Tonnes 16.00R24 Single 40.0 Tonnes 40.0 Tonnes WBA-RB1/MK2
Notes:
1) Please contact York for detailed General Arrangement drawings.
2) All Wheel Fittings Are ISO With M22 or M24 Wheel Stud (10 x 335 PCD).
3) This WB is not suitable for port Operations.
Page: 6.1
Model NumberTyre
TyreAxle Beam
@ Axle Capacity
Model
Number
Axle Beam
@ Axle Capacity
Walking Beam page 1
Argonaut Bogies AGB - Over and Underslung assemblies
Wheel Fitting Capacity Capacity Model Approximated
No. Stud x PCD Tonnes @ 20km/h Tonnes @ 40km/h Number Weight - Kg
8.25R15 60 46
10.00R15 70 52
10.00R20 ISO 10 x 335 70 52 AGB-80/20/MK2 2,800
12.00R20 78 60
12.00R24 85 65
24.00R21 85 65
24.00R20.5 85 65
Tyre : 8.25 x 15 10.00 x 15
DIM. A 2820 3000
DIM. B 1320 1410
DIM.C 815 815
DIM. D 1500 1590
DIM. E 1362 1362
DIM. F 850 Ref. 935 Ref.
Tyre : 10.00 x 20
DIM. A 3210
DIM. B 1510
DIM.C 890
DIM. D 1700
DIM. E 1362
DIM. F 1080 Ref.
Tyre : 11.00 x 20 12.00 x 20
DIM. A 3405 3512
DIM. B 1605 1662
DIM.C 965 965
DIM. D 1800 1890
DIM. E 1562 1562
DIM. F 1110 Ref. 1154 Ref.
Notes:
1. Please contact York for detailed General Arrangement drawings.
2. All wheel fittings are ISO with M22 wheel stud. / M24 is
optional for AGB-100.
3. Other Tyre Sizes and Axle centers is available on request. (E)
Tyre size
AGB-100/20MK2
AGB-80/15/MK3
Twin
Single
ISO 10 x 225
ISO 10 x 335
AGB - 80 / 15
AGB - 80 / 20
AGB - 100 / 20
2,300
3,000
AGB Page 1
King Pins (2"- 3.5") Demountable and Welded
Weld-In King Pin
SIZE
105KN YKW50M10
105KN YKW50M12
Bolt/Weld-In King Pin
SIZE
105KN YKZ50M10 162KN YKZ50D12
105KN YKZ50M12
3.5" / 90mm 105KN YKZ50M16
Demountable King Pin
SIZE
150KN Y-KP2108
162KN Y-KZA5008D
150KN Y-KP2210
162KN Y-KZA5010D
150KN Y-KP2312
162KN Y-KZA5012D
140KN YKZA9012M
140KN YKZA9016M
With Retention Plate , Bolt set included
12
163.5" / 90mm
16
2" / 50mm 10 105KN YKZA5010M
12 105KN YKZA5012M
2" / 50mm
Trailer Rubbing
Plate ThicknessM Rated D Value
8 105KN YKZA5008M
Trailer Rubbing
Plate ThicknessM Rated D Value
10
12
2" / 50mm
Trailer Rubbing
Plate ThicknessM Rated
10
12
Bolt M14 - ISO Standard
King Pin
Semi Trailer Landing Gears ‐ YT‐28A‐2 & YF‐28A‐2
YT‐28A YF‐28A Standard Swivel Foot ( SF )
Compensating Foot ( CF )
For Air Suspension
6400 6400Static Load ( Kg)
Lift Capacity ( Kg ) 28000 28000
840 857
Max Travel ( mm ) 480 480
High Gear (mm) 5.43 5.43
Side Load Capacity (kg) 13000 13000
Specification YT‐28A YF‐28A
Standard Weight ( kg ) 110 110
Crank Force (kg ) 22 22
Low Gear (mm) 0.72 0.72
Retract Height ( mm )
Landing Gear
Container ‐ Twistlock Assembly
Part Number Description
790034 Twist Lock Assy
790034/01 Twist Lock Centre
Twist Lock
Steel Wheel Rims for Trailers.
TUBED WHEEL RIMS
S/N PART No. RIM TYPE RIM SIZENO HOLE
X PCD No. x mm
BORE DIAmm
HOLETYPE
MATERIALOFFSET
MIN
CPACITY MINKg
1 TT6.5*15,10D TUBED 6.5x15 10x 225 176 DIN STEEL 130 2725
2 TT6.5*15,10I TUBED 6.5x15 10x 225 176 ISO STEEL 152 2725
3 TT7.5*15,10D TUBED 7.5x15 10x 225 176 DIN STEEL 152 3150
4 TT7.5*15,10I TUBED 7.5x15 10x 225 176 ISO STEEL 167 3150
5 TT7.5*20,10B TUBED 7.5x20 10x335 281 BSF STEEL 167 3450
6 TT7.5*20,10I TUBED 7.5x20 10x335 281 ISO STEEL 167 3450
7 TT7.5*20,8J TUBED 7.5x20 8x285 281 JAP STEEL 167 3450
8 TT8.0*20,10I TUBED 8.0x20 10x335 281 ISO STEEL 167 4000
9 TT8.0*20,10IZ TUBED 8.0x20 10x335 281 ISO STEEL 0 4000
10 TT8.5*20,10I TUBED 8.5x20 10x335 281 ISO STEEL 178 4000
11 TT8.5*20,10IZ TUBED 8.5x20 10x335 281 ISO STEEL 0 4000
12 TT8.5*24,10I TUBED 8.5x24 10x335 281 ISO STEEL 178 4000
13 TT10.0*20,10IZ TUBED 10x20 10x335 281 ISO STEEL 0 6600
TUBELESS WHEEL RIMS
S/N PART No. RIM TYPE RIM SIZENO HOLE
X PCD No. x mm
BORE DIAmm
HOLETYPE
MATERIALOFFSET
MIN
CPACITY MINKg
1 TL6.0*17.5,10I TUBELESS 6.0*17.5 10X225 176 ISO STEEL 128 2180
2 TL6.75*17.5,10I TUBELESS 6.75*17.5 10X225 176 ISO STEEL 137 2725
3 TL7.5*22.5,10I TUBELESS 7.7*22.5 10X335 281 ISO STEEL 160 3550
4 TL8.25*22.5,10H TUBELESS 8.25*22.5 10X285.75 220 ISO STEEL 170 3750
5 TL8.25*22.5,10I TUBELESS 8.25*22.5 10X335 281 ISO STEEL 170 3750
6 TL9.0*22.5,10I TUBELESS 9.0*22.5 10X335 281 ISO STEEL 175 4000
7 TL11.75*22.5 ,10IZ TUBELESS 11.75*22.5 10X335 281 ISO STEEL 0 4500
8 TL13.00*22.5*10Z TUBELESS 13.0*22.5 10X335 281 ISO STEEL 0 5150
9 TL14.00*22.5,10IZ TUBELESS 14.0*22.5 10X335 281 ISO STEEL 0 5800
10 TLA7.5*19.5*8 TUBELESS 7.5x195*8 8X275 221 ISO Aluminium 160 2800
11 TLA7.5*22.5, 10 TUBELESS 7.5*22.5 10X285.75 220 ISO Aluminium 160 3450
12 TL7.5*22.5,10H TUBELESS 7.5*22.5 10X335 281 ISO Aluminium 160 3450
Page : 12.1
Rims
Air Leveling Valve Kits for Trailer Air Suspension Modules
Air Susp. Piping System
Semi-Trailer Application Kit NumberSingle B01010
Tandem B02010
Tandem With 1 Axle Lift B02020
Tri-Axle B03010
Tri-Axle With 1 Axle Lift B03020
Tri-Axle With 2 Axle Lifts B03030
Raise/Lower/Hold Valve B04020
Dump/Lower Valve B04030
Air Kit Components
Air Kit Page 1
Complete Brake Kits -Basic
Semi-Trailer KitApplication Number
Single B05010
Tandem B06010
Tri-Axle B07010
Note : All brake kits are used with ratchet hand brake, not included.
Complete Brake Kits - Basic
Semi-Trailer KitApplication Number
Single B05030
Tandem B06050
Tri-Axle B07080
Note : All brake kits come with trailer park valve.
Note : Brake kits for full trailer and other semi-trailer designs are available on request.
Sp
rin
g
Bra
ke
Ch
amb
er
Ser
vice
Bra
ke
Ch
amb
er
Brake Kit Page 1
YTE- Q-Coupler (2") - YTE -YC Coupler (2" & 3.5") Pressed High Tensile top Plate
Q- Plus Coupler - (D Value = 165 kN)Kingpin Mounting Vertical Weight Oscillation Model
Size Height (H) Load (Kg) (Degree) Number(mm) (mm) (kg) (Q)
150 895101/150/MK2
180 895101/180/MK2
210 895101/210/MK2
Note :1) GCW - 80,000kg for all models.2) 180mm mounting height is standard, mounting patterns - 6 holes DIN.
YC - Couplers Kingpin Mounting Vertical Weight Oscillation Model
Size Height Load (Kg) (Degree) Number(mm) (mm) (kg)
173 YC-50-SA/MK3
200 YC-90-SA/MK3
Note :1) GCW (Kg) - 50,000kg for YC-50SA MK3
- 100,000kg for YC-90SA MK32) Mounting patterns - 6 holes DIN.
20,000 140 Single 1550 (2")
50 20,000 117 Single 15
5th Wheel Page 1
1. DEFINITIONS
“Conditions” means these Terms and Conditions of Sale; “Customer” means a person, firm or corporation seeking to acquire
goods from the Supplier, and if there is more than one, these Conditions bind them jointly and each of them severally;
“Goods” means goods supplied by the Supplier to the Customer; “GST” the goods and services tax which will apply to transactions
for the sale of goods from 1 July 2000; and “YORK” means YORK TRANSPORT EQUIPMENT PTY LTD
(ABN 25 006 303 206).
2. BASIS OF CONTRACT
2.1 The Conditions apply exclusively to every contract for the sale of goods by YORK to the Customer and cannot be varied or supplanted by any other condition(s) including those that may be proffered by a Customer or printed on a Customer’s purchase order unless expressly accepted in writing by YORK.
2.2 Any written quotation or Order form provided by YORK to the Customer in respect of the proposed supply of goods is deemed to be an invitation only to the Customer to place an order based upon that quotation. Quotations are valid for 30 days from the quotation date.
2.3 Orders made upon order forms approved by YORK from time to time are subject to these Conditions. YORK may only accept an Order by:
(a) Notifying the Purchaser in writing of the acceptance;(b) Notifying the Purchaser in writing of the availability
of the Goods for delivery; or(c) delivery of the Goods to the Purchaser.
2.4 Each acceptance of a separate Order by YORK will be deemed to be a separate Contract.
3. PAYMENT
Unless otherwise specified by YORK, payment for Goods must be made within 30 days of the date of issue of an invoice by YORK.
4. PRICING
4.1 Prices for the supply of Goods exclude GST, and any other taxes, duties or imposts imposed on or in relation to the goods in Australia or overseas. As from the date of imposition of a GST, YORK will be entitled to increase its prices for goods by an amount equal to the GST payable on the goods.
4.2 The Customer will arrange and pay for all costs associated with the carriage and insurance of the goods from YORK’s nominated collection address unless otherwise specified by YORK.
4.3 The prices specified for goods may be adjusted by YORK at any time before the Delivery Date, whether or not a price has previously been specified.
5. PAYMENT DEFAULT
5.1 If the Customer defaults in payment by the due date of any amount payable to YORK, then all money which would become payable by the Customer to YORK at a later date on any account, becomes immediately due and payable without the requirement of any notice to the Customer, and YORK may, without prejudice to any other remedy available to it :-
(a) claim a general lien over all the Customer’s property in the possession of YORK and, subject to giving 14 days written notice to the Customer, sell the property by private treaty or public auction, whichever YORK in its sole discretion deems appropriate, and allocate the proceeds to the repayment of its sale costs and expenses and any sum which is due and payable by the Customer;
(b) charge the Customer interest on any sum due at the prevailing rate pursuant to the Penalty Interest Rates Act 1983 (Vic.) plus 2% cent for the period from the due date until the date of payment in full;
(c) charge the Customer for all expenses and costs (including legal costs on a solicitor/own client basis) incurred by it in taking whatever action it deems appropriate to recover any sum due;
(d) cease or suspend for such period as YORK thinks fit, supply of goods to the Customer without liability to the Customer or any third party for any loss or damage whether of a direct or consequential nature.
6. PASSING OF PROPERTY
Until full payment in cleared funds is received by YORK for all goods sold to the Customer, as well as all other amounts owing on any account to YORK by the Customer:-
(a) title in the goods does not pass to the Customer;
(b) the goods are held as fiduciary bailee and agent for YORK;
(c) YORK may without notice, enter any premises where it suspects the goods may be and remove them, notwithstanding that they may have been attached to other goods not the property of YORK, and for this purpose the Customer irrevocably licences YORK to enter such premises and also indemnifies YORK from and against all costs, claims, demands or actions by any party arising from such action.
7. PERFORMANCE OF CONTRACT
Any period or date stated by YORK for the delivery of the goods is intended as an estimate only and is not a contractual commitment. YORK will use its best endeavours to meet any estimated dates but will in no circumstances whatsoever be liable for any loss or damage suffered by the Customer or any third party for failure to meet any estimated date even if such loss or damage is caused by the act or omission of YORK.
8.0 DELIVERY AND RISK IN GOODS
8.1 Risk in the goods and all insurance responsibility for theft, damage or loss in respect of the goods will pass to the Customer upon the goods being loaded onto the relevant transport at YORKs premises, whether such transport is arranged by YORK or the Customer.
8.2 The Customer agrees to accept partial delivery of goods however the Customer cannot insist upon a partial delivery or pre-delivery of goods.
9.0 SPECIFICATIONS
YORK has no responsibility whatsoever to verify specifications supplied by the Customer.
22.1 GENERAL TERMS AND CONDITION OF SALES
10. LIABILITY
10.1 All conditions and warranties implied into contracts for the supply of goods at law or pursuant to any Federal or State legislation are excluded to the maximum extent permitted.
10.2 Subject to and to the extent permitted by State and Federal legislation applicable to the sale of goods, replacement or repair of the goods is the absolute limit of YORK’s liability howsoever arising under or in connection with the supply of the goods, the description, quality, condition, performance, assembly, manufacture, merchantability or fitness for purpose of the goods or alternatively the sale, use of or any other dealings with the goods by the Customer or any third party.
10.3 YORK is not liable for any consequential loss, damage or expense suffered by the Customer or any third party however caused, including but not limited to loss of profits, business or goodwill or any liability to a third party.
10.4 Any advice, recommendation, information or assistance provided by YORK in relation to the goods supplied by it or their use or application is given in good faith, is believed by YORK to be appropriate and reliable, however, it is provided with a disclaimer for any liability or responsibility on the part of YORK.
11. WARRANTY
11.1 Goods supplied shall be free from defects in materials and workmanship and material for a period of 1 year from the date of delivery.
11.2 This warranty does not apply in circumstances where:(a) the goods are not defective;(b) the goods were used for a purpose other than for which they
were intended;(c) the goods were repaired, modified or altered by any person
other than YORK;(d) the defect has arisen due to misuse, neglect or accident;(e) the defect has arisen due to the incorrect installation of the
goods;(f) the goods have not been stored or maintained as
recommended by YORK;(g) the defect has arisen due to normal wear and tear on the
goods; or(h) the Customer is in breach of the Conditions.
11.3 YORK’s liability under this warranty is limited to repairing or replacing any products that YORK accepts are defective and covered by this warranty.
11.4 In order to make a claim under this warranty, a person must:(a) give YORK written details of any defect in the products
together with documentary proof of the date of purchase and date of installation of end user of the products within 30 days of identifying the defect;
(b) return the defective products to YORK or allow YORK or its employees or agents to inspect the products;
(c) provide any information requested by YORK in relation the products or installation of the products.
11.5 YORK accepts no responsibility for defective goods not of its manufacture. In the case of any claim, the item will be returned to the original supplier for examination. The Customer will be entitled
to the benefit of any warranty given by the original supplier should they be found to be defective. YORK will not be under any obligation to provide replacement parts while the examination of the item is undertaken by the original supplier.
12. RETURNS AND EXCHANGES
12.1 Except as is otherwise required by law claims for shortages in delivery or returns must be made within 14 days of the date of delivery.
12.2 YORK will not under any circumstances accept goods for return:(a) which have been specifically produced, imported or acquired
to fulfil any contract;(b) which have been altered in any way;(c) which have been used; or(d) which are not in their original condition.
12.3 If goods are accepted for return by YORK, it must be done within the stipulated 14 days to YORK’s Warehouse Melbourne. The Purchaser will receive a credit for the returned goods equal to the price charged by YORK less a 10% deduction for handling and restocking charges.
13. CANCELLATION
13.1 If, through circumstances beyond the control of YORK, YORK is unable to supply the goods, then YORK may cancel the Customer’s order (even if it has already been accepted) by notice in writing to the Customer. YORK will be under no liability to the Customer or any third party for any damages or losses, direct or indirect, resulting from such cancellation.
13.2 No purported cancellation or suspension of an order or any part thereof by the Customer is binding on YORK after that order has been accepted by YORK.
14. JURISDICTION
These Conditions will be governed by the laws of Victoria and the parties hereby submit to the exclusive jurisdiction of the Victorian Courts and the Federal Court of Australia (Victoria Registry).