Embed Size (px)
Citation preview
bility Packer Test Procedure
GEO-Packers TM DST PACKER TEST TOOL
GEO-PACKER 0 213" HO DST SINGLE PACKER TESTING TOOL
INFLATION / WIRELINE SEALING TIGHT HEAD
HQ54LP275E0.5
RIG WIRELINE
1. Pull th inneYTe assembly from the core barrel, leaving the drill string in place.
2. Elevate the drill strin9 off the drill hole bottom and I expose th permeaBlity zone.
3. Secure/ st bilise the drill )1,tring in place. umig• Install the sealing tight head.
5. Lower the packer through the sealing tight head and drilftring, positioning into the core barrel. Install steel washers and rubber shies in the tight
ead and tighten the compression cap. 7. Co ect the nylon inflation tube to the g s/air supply. 8. Slow inflate the permeability packer in i rements
of until e desired pressure is met.
--HQ DRILL RODS inject wa r through the tight head asse
I ak, packer into • he test zone. 10. ermeability est is run in under instruction b
oject engin r. 1 1Once
testing is omplete deflate the packer. 12. Make suds pack r is fully deflated before movin
from the drill ho e. 13. Undo comp si n tight head and remove rubbe
seals and stee shers. 14. Reinstall the co pression cap and remove the packs 15. Remove the seal ng tight head and then lower the inner tube assembl into position. 16. Connect the dr" I rods, lowering the drill string t
the hole botto and restart drilling. 7. OHS procedu es must be followed.
18. Inflation an • use of packers and packer equip is at he op rators own risk.
r.
1111 ty HO WIREL 4 ORING DIAMOND BIT Bit set OD ' et ID
3.77" 2. CORED HOLE SIZE
3.78"-A
rgitE
V HO DRILL ROD SPECIFICATIONS ID (inch) OD (inch) WEIGHT (113) VOL ME (Gal)
HO 3.063 3.5 76.896 31.808
Max Working pressure vs hole diameter Boreholes diameter (in) 2.2" 2.4" 2.6" 2.8" 3" 3.2" ac 3.5" 3.7" 4" 4.1" 4.3" 4.5" Percentage inflation diameter 4.8 14.3 23.8 33.3 42.9 52.4 61.9 66.7 76.2 90.5 95.2 104.8 114.3
Inflation pressure (PSI) 2250 2000 1750 1450 1150 1000 850 725 580 500 435 360 290
Non confined Free air Inflation Diameter (in) 2.2" 2.4" 2.6" 2.8" 3" 3.2" 3.4" 3.5" 3.T 4" 4.1" 4.3'" 4.5" Inflation pressure (PSI) 22 30 36 41 45 52 61 67 80 87 94 116 160
Replacement Inflatable Packers and Elements Pty Ltd 29 Wheeler St Belmont 6104, Perth Western Australia
Tel: (+61 (08) 9475 0700 Fax: +61 (08) 9475 0770 [email protected] www.ripe-packers.com • WA Australia Supplier Manufacturer of inflatable Packers for DST Well Packer Testing Permeability single/ double packer testing equipment and Services AU.
Perm bility Packer Test Procedure
WATER INJECTION HO
PIP
GEO-Packers TM DST PACKER TEST TOOL
GEO-PACKER 213" HQ DST DOUBLE PACKER TESTING TOOL
NTIGHT YI I IE AND
HQ54LP27SE0.5
RIG WIRELINE
SMALL BORE NYLON INFLAT
0 DRILL RODS
HO CORED HOLE 4-
ROD STEM PACKER
0 BIT SEATING SU
OPEN HOLE BOTTOM PACKER 1 3414
1. Pull th inneYTe assembly from the core barrel, leaving the drill string in place. Elevate the drill strin9 off the drill hole bottom and
I expose th permeaBlity zone. Secure/ st bilise the drill)ktring in place. Install the sealing tight head. Lower the packer through the sealing tight head and drilPtring, positioning into the core barrel. Install steel washers and rubber shies in the tight
ead and tighten the compression cap. 7. Co ect the nylon inflation tube to the g s/air supply. 8. Slow inflate the permeability packer in i rements
of until e desired pressure is met. Inject wa r through the tight head asse packer into • he test zone.
ermeability est is run in under instruction b oject engin er.
1 1 Once testing is omplete deflate the packer. 12. Make suds pack r is fully deflated before movin
from the drill ho e. 13. Undo comp in tight head and remove rubbe
seals and stee shers. 14. Reinstall the co pression cap and remove the packs r. 15. Remove the seal ng tight head and then lower the inner tube assembl into position. 16. Connect the dr' I rods, lowering the drill string t
the hole botto and restart drilling. 7. OHS procedu es must be followed.
flation an • use of packers and packer equip hg op rators own risk.
2.
LINE 3.
5.
0 WIRELII CORING DIAMOND BIT SPEC
t set OD Bit set ID CORED HOLE SIZE M PACKER 2 3.77- 3.78- 2.5-
HO DRILL ROD SPECIFICATIONS ID (inch) OD (inch)
HO
3.063
3.5
WEIGHT Ay: ME (Gal) IZE 76.896 31.808
Max Working pressure vs hole diameter Boreholes diameter (in) 2.2" 2.4" 2.6" 2.8" 3" 3.2" 3.4- 3.5" 3.7" 4" 4.1" 4.3" 4.5"
Percentage inflation diameter 4.8 14.3 23.8 33.3 42.9 52.4 61.9 66.7 76.2 90.5 95.2 104.8 114.3
Inflation pressure (PSI) 2250 2000 1750 1450 1150 1000 850 725 580 500 435 360 290
Non confined Free air Inflation Diameter (in) 2.2" 2.4" 2.6" 2.8" 3" 3.2" 3.4" 3.5" 37 4" 4.1" 4.3" 4.5"
Inflation pressure (PSI) 22 30 36 41 45 52 61 67 80 87 94 116 160
Replacement Inflatable Packers and Elements Pty Ltd 29 Wheeler St Belmont 6104, Perth Western Australia
Tel: (+6 1 (08) 9475 0700 Fax: +61 (08) 9475 0770 [email protected] www.ripe-packers.com • WA Australia Supplier Manufacturer of Inflatable Packers for DST Well Packer Testing Permeability single/ double packer testing equipment and Services
