2
Perm bility Packer Test Procedure GEO-Packers TM DST PACKER TEST TOOL GEO-PACKER 2125" HO DST SINGLE PACKER TESTING TOOL .-1 NFLATION / WIRELINE SEALING TIGHT HEAD H054LP275E0.5 RIG WIRELINE 1. Pull th inneYTe assembly from the core barrel, leaving the drill string in place. 2. Elevate the drill stria9 off the drill hole bottom and I expose th permeaBlity zone. Secure/ st bilise the drill)ktring in place. Install the sealing tight head. Lower the packer through the sealing tight head and drilPtring, positioning into the core barrel. Install steel washers and rubber shies in the tight ead and tighten the compression cap. 7. Co ect the nylon inflation tube to the g s/air supply. 8. Slow inflate the permeability packer in i rements of until e desired pressure is met. Inject wa r through the tight head asse packer into • he test zone. 10. ermeability est is run in under instruction b oject engin er. 1 1 Once testing is omplete deflate the packer. 12. Make suee pack r is fully deflated before movin from the drill ho e. 3. Undo comp si n tight head and remove rubbe seals and stee shers. 14. Reinstall the co pression cap and remove the pack r. 15. Remove the seal ng tight head and then lower the inner tube assembl into position. 16. Connect the dr' I rods, lowering the drill string t the hole botto and restart drilling. 17. OHS procedu es must be followed. 18. Inflation an use of packers and packer equip is a h rators own risk. 3.78 - Max Working pressure vs hole diameter Boreholes diameter lin) 2.7' 2.4" 2.6" 2.8" 3" 3.2 - 3.4" 3.5" 3.7" 4" 4.1" 4.3" 4.5" Percentage inflation diameter 4.8 14.3 23.8 33.3 42.9 52.4 61.9 66.7 76.2 90.5 95.2 104.8 114.3 Inflation pressure (PSI) 2250 2000 1750 1450 1150 1000 850 725 580 500 435 360 290 Non confined Free air Inflation Diameter (in) 2.2" 2.4" 2.6" 2.8" 3" 3.2"' 3.4" 3.5" 3.7" 4" 4.1" 4.3 - 4.5" Inflation pressure (PSI) 22 30 36 41 45 52 61 67 80 87 94 116 160 Replacement Inflatable Packers and Elements Pty Ltd 29 Wheeler St Belmont 6104, Perth Western Australia Tel: (+61 (08) 9475 0700 Fax: +61 (08) 9475 0770 [email protected] www.ripe-packers.com WA Australia Supplier Manufacturer of Inflatable Packers for DST Well Packer Testing Permeability single/ double packer testing equipment and Services AU.

2.125 Dst Packer Test Tool

Embed Size (px)

Citation preview

Perm bility Packer Test Procedure

GEO-Packers TM DST PACKER TEST TOOL

GEO-PACKER 2125" HO DST SINGLE PACKER TESTING TOOL

.-1

NFLATION / WIRELINE SEALING TIGHT HEAD

H054LP275E0.5

RIG WIRELINE

1. Pull th inneYTe assembly from the core barrel, leaving the drill string in place.

2. Elevate the drill stria9 off the drill hole bottom and I expose th permeaBlity zone.

Secure/ st bilise the drill)ktring in place. Install the sealing tight head. Lower the packer through the sealing tight head and drilPtring, positioning into the core barrel. Install steel washers and rubber shies in the tight

ead and tighten the compression cap. 7. Co ect the nylon inflation tube to the g s/air supply. 8. Slow inflate the permeability packer in i rements

of until e desired pressure is met. Inject wa r through the tight head asse packer into • he test zone.

10. ermeability est is run in under instruction b oject engin er.

1 1 Once testing is omplete deflate the packer. 12. Make suee pack r is fully deflated before movin

from the drill ho e. 3. Undo comp si n tight head and remove rubbe

seals and stee shers. 14. Reinstall the co pression cap and remove the pack r. 15. Remove the seal ng tight head and then lower the inner tube assembl into position. 16. Connect the dr' I rods, lowering the drill string t

the hole botto and restart drilling. 17. OHS procedu es must be followed. 18. Inflation an • use of packers and packer equip

is a h rators own risk.

3.78-

Max Working pressure vs hole diameter Boreholes diameter lin) 2.7' 2.4" 2.6" 2.8" 3" 3.2- 3.4" 3.5" 3.7" 4" 4.1" 4.3" 4.5"

Percentage inflation diameter 4.8 14.3 23.8 33.3 42.9 52.4 61.9 66.7 76.2 90.5 95.2 104.8 114.3

Inflation pressure (PSI) 2250 2000 1750 1450 1150 1000 850 725 580 500 435 360 290

Non confined Free air Inflation Diameter (in) 2.2" 2.4" 2.6" 2.8" 3" 3.2"' 3.4" 3.5" 3.7" 4" 4.1" 4.3- 4.5"

Inflation pressure (PSI) 22 30 36 41 45 52 61 67 80 87 94 116 160

Replacement Inflatable Packers and Elements Pty Ltd 29 Wheeler St Belmont 6104, Perth Western Australia

Tel: (+61 (08) 9475 0700 Fax: +61 (08) 9475 0770 [email protected] www.ripe-packers.com • WA Australia Supplier Manufacturer of Inflatable Packers for DST Well Packer Testing Permeability single/ double packer testing equipment and Services AU.

Perm bility Packer Test Procedure

rators own risk. h

GEO-Packers TM DST PACKER TEST TOOL

GEO-PACKER 0 2125" HO DST DOUBLE PACKER TESTING TOOL

INFLATION / WIRELINE SEALING TIGHT HEAD

HQ54LP27SE0.5

RIG WIRELINE ATER INJECTION HO

ALL BORE YLON INFLATI INE

2.

3.

1.

SURFACE NDUCTO

5.

A

CI RODS DRIL 4 HO CORE HOLE

Pull th inneYTe assembly from the core barrel, leaving the drill string in place. Elevate the drill stria9 off the drill hole bottom and

I expose th permeaBlity zone. Secure/ st bilise the drill)ktring in place. Install the sealing tight head. Lower the packer through the sealing tight head and drilPtring, positioning into the core barrel. Install steel washers and rubber shies in the tight

ead and tighten the compression cap. Co ect the nylon inflation tube to the g s/air supply. Slow inflate the permeability packer in i rements of until e desired pressure is met. Inject wa r through the tight head asse packer into • he test zone.

ermeability est is run in under instruction b oject engin er.

PACKER

UB

WIREL OR1NG DIAMOND BIT

Once testing is Make suee pack from the drill ho

13. Undo comp seals and stee

14. Reinstall the co 15. Remove the seal inner tube assembl 16. Connect the dr'

the hole botto 7. OHS procedu

flation an

omplete deflate the packer. r is fully deflated before movin e. n tight head and remove rubbe shers.

pression cap and remove the packs ng tight head and then lower the into position.

I rods, lowering the drill string t and restart drilling.

es must be followed. use of packers and packer equip

SI

r.

Bit set OD Bit stot ID HOLE SIZE 3.7T I Is. 3.78"

KER 2

HO DRILL ROD SPE CATIONS ID (inch) OD (inch) WEIGHT b) VOL (Gal)

Ni ithr

31.808 HQ

3.063 3.5

76.896

Max Working pressure vs hole diameter Boreholes diameter (in) 2.2" 2.4" 2.6" 2.8" 3" 3.2" 3.4" 3.5" 3.7" 4" 4.1" 4.3" 4.5"

Percentage inflation diameter 4.8 14.3 23.8 33.3 42.9 52.4 61.9 66.7 76.2 90.5 95.2 104.8 114.3

Inflation pressure (PSI) 2250 2000 1750 1450 1150 1000 850 725 580 500 435 360 290

Non confined Free air Inflation Diameter (in) 2.2" 2.4" 2.6" 2.8" 3" 3.2" 3.4" 3.5" 3.T 4" 4.1" 4.3" 4.5"

Inflation pressure (PSI) 22 30 36 41 45 52 61 67 80 87 94 116 160

Replacement Inflatable Packers and Elements Pty Ltd 29 Wheeler St Belmont 6104, Perth Western Australia

Tel: (+61 (08) 9475 0700 Fax: +61 (081 9475 0770 [email protected] www.ripe-packers.com • WA Australia Supplier Manufacturer of Inflatable Packers for DST Well Packer Testing Permeability single/ double packer testing equipment and Services AU.