Upload
nagaraj-ramachandrappa
View
233
Download
0
Embed Size (px)
Citation preview
8/12/2019 2-Lectures Lec 07 Torsion
1/11
23-S
Chapter 4
Load and Stress AnalysisLoad and Stress Analysis
A. Bazoune
TorsionTorsion
LecLec. 7. 7
23-Sep-07 1
23-Sep-07 2
https://ecourses.ou.edu/cgi-bin/ebook.cgi?doc=&topic=me&chap_sec=02.1&page=theory
TORSIONTORSION
TORSIONTORSION
Any moment vector that is collinear with an axisof a mechanical element is called a torquevector, because the moment causes the element
to be twisted about that axis.
A bar subjected to such a moment is also said tobe in torsion.
Designated by drawing arrows on the surface ofthe bar to indicate direction, or by drawingtorque-vector arrows along the axes of twist ofthe bar23-Sep-07 3
8/12/2019 2-Lectures Lec 07 Torsion
2/11
23-S
PRACTICAL EXAMPLESPRACTICAL EXAMPLES
Transmit power from one device to another
Turbine to a generator
Engine to the wheels
Motor to the pulley
23-Sep-07 4
AssumptionsAssumptions
The bar is acted upon by a pure torque.
The section under consideration are remote fromthe point of application of the load and from achange in diameter.
Adjacent cross sections originally plane andparallel remain plane and parallel after twisting,and any radial line remains straight.
The material obeys Hookes law.23-Sep-07 5
Fig. 4.2323-Sep-07 6
8/12/2019 2-Lectures Lec 07 Torsion
3/11
23-S
Shear StressShear Stress
23-Sep-07 7
The angle of twist for a solid round bar is
where
T= torque
l = length
G = modulus of rigidity
J = polar second moment of area
T l
G J = (4-35)
Angle of TwistAngle of Twist
23-Sep-07 8
For a solid round bar, the shear stress is zero atthe centre and maximum at the surface.
The distribution is proportional to radius and isgiven by
Designating ras the radius to the outer surface,
we have
Eq. (4-37) applies onlyto circular sections.
T
J
=
max
Tr
J =
(4-36)
(4-37)
Shear StressShear Stress
23-Sep-07 9
8/12/2019 2-Lectures Lec 07 Torsion
4/11
23-S
For a solid round section,
where d= diameter of the bar.
For a hollow round section,
4
32
d
J
=
( )4 432
o iJ d d
=
(4-38)
(4-39)
23-Sep-07 10
To obtain the Torque T from the power andspeed of a rotating shaft, using USC units, use thefollowing equation
where
H= power, hp
T = torque, lb-in
n = shaft speed, rev./min
F= force, lb
V= velocity, ft/min.
2
33,000 33,000(12) 63,025
F V Tn T nH
= = = (4-40)
23-Sep-07 11
When SI units are used, the equation is
where
H = power, W
T= torque, N-m
= angular velocity, rad./s
The torque Tcorresponding to the power in watts
is given approximately by
where n : rev./min.
9.55H
Tn
=
H T= (4-41)
(4-42)
23-Sep-07 12
8/12/2019 2-Lectures Lec 07 Torsion
5/11
23-S
Torsional Stresses in NonTorsional Stresses in Non--CircularCircularCrossCross--section Memberssection Members
There are some applications in machinery for non-circular cross-section members and shafts where a
regular polygonal cross-section is useful intransmitting torque to a gear or pulley that canhave an axial change in position. Because no keyor keyway is needed, the possibility of a lost keyis avoided.
23-Sep-07 13
Saint Venant (1855) showed that in a
rectangular bc section bar occurs in the middle of
the longest side b and is of magnitudeformula
where b is the longer side, and a factor that isfunction of the ratio b/c as shown in Table of Page 139.
The angle of twist is given by
where is a function of the ratio b/c as shown in
Table of Page 139.
max 2 2
1.83
/
T T
bc b c b c
= = +
(4-43)
3
Tl
bc G
= (4-44)
max
23-Sep-07 14
ExampleExample 44--88 TextbookTextbook
23-Sep-07 15
8/12/2019 2-Lectures Lec 07 Torsion
6/11
23-S
ExampleExample 44--88 TextbookTextbookContdContd
23-Sep-07 16
23-Sep-07 17
23-Sep-07 18
8/12/2019 2-Lectures Lec 07 Torsion
7/11
23-S
23-Sep-07 19
23-Sep-07 20
ExampleExample 44--99TextbookTextbook
Fig. 4.26a
23-Sep-07 21
8/12/2019 2-Lectures Lec 07 Torsion
8/11
23-S
ExampleExample 44--99 TextbookTextbook
23-Sep-07 22
23-Sep-07 23
23-Sep-07 24
8/12/2019 2-Lectures Lec 07 Torsion
9/11
23-S
Closed ThinClosed Thin--Walled TubesWalled Tubes (t
8/12/2019 2-Lectures Lec 07 Torsion
10/11
23-S
23-Sep-07 28
ExampleExample 44--1111 TextbookTextbook
23-Sep-07 29
Open ThinOpen Thin--Walled SectionsWalled Sections
When the median wall line is not closed, it is to be open.Fig. 4-29 shows some examples.
Fig. 4-29Some open thin-walled sections
23-Sep-07 30
8/12/2019 2-Lectures Lec 07 Torsion
11/11
23-S
Open ThinOpen Thin--Walled SectionsWalled Sections
Open sections in torsion, where the wall is thin, haverelations derived from the membrane analogy theory asfollows:
where
: shear stress
G : shear modulus
1: the angle of twist per unit length
L : length of the median line
c : wall thikness
1 2
3TG c
Lc = =
23-Sep-07 31
ExampleExample 44--1212 TextbookTextbook
23-Sep-07 32
23-Sep-07 33