Upload
jemimah-heath
View
221
Download
2
Tags:
Embed Size (px)
Citation preview
2. Definitions2. Definitions
Assoc.Prof.Dr. Ahmet Zafer Şenalpe-mail: e-mail: [email protected]@gmail.com
Mechanical Engineering DepartmentGebze Technical University
ME 612ME 612 Metal Forming and Theory of Plasticity Metal Forming and Theory of Plasticity
1)Decomposition of strain into elastic and plastic parts.2)Yield criteria: Determines when the metal will behave elastically or plastically.3)Work hardening rules: Controls the shape of the stress-strain curve in plastic region.4) Plastic flow rule: Determines the stress-plastic strain relation in multiaxial loading. 5) Elastic unloading criteria: Models the irreversible behavior.
Dr. Ahmet Zafer Şenalp ME 612
2Mechanical Engineering Department, GTU
2. Definitions2. Definitions
2.1. 2.1. Basic Thoughts Basic Thoughts in in Metal Plasticity Metal Plasticity MModelingodeling
2.2. Tensile Test2.2. Tensile Test
Figure 2.1. (a) Load-extension or nominal stress-strain plot for a ductile material (b) The expansion of the strain axis to illustrate the elastic region
Dr. Ahmet Zafer Şenalp ME 612
3Mechanical Engineering Department, GTU
2. Definitions2. Definitions
As shown in the figure at the beginning strain varies linearly with stress. In this region deformation is elestic. i.e. With the removal of load the object recovers its original shape.
u
2.2. Tensile Test2.2. Tensile Test
The slope of the line is shown by E and elasticity modulus is called Young modulus. Along the line Hooke’s Law is valid;
In tensile test as the specimen elongates the cross sectional area decreases.
is denoted as yield point. After yield point Hooke’s law is not valid.
point is the maximum stress value at which permanent deformation is not observed.
is the point of maximum load application or maximum stress value. After this value if the load is not removed the specimen goes to fracture with decreasing load.
Dr. Ahmet Zafer Şenalp ME 612
4Mechanical Engineering Department, GTU
2. Definitions2. Definitions
E
y
y
u
(2.1)
2.2. Tensile Test2.2. Tensile Test
Poisson's ratio (ν), is the ratio, when a sample object is stretched, of the contraction or transverse strain (perpendicular to the applied load), to the extension or axial strain (in the direction of the applied load).
When a material is compressed in one direction, it usually tends to expand in the other two directions perpendicular to the direction of compression. This phenomenon is called the Poisson effect. Poisson's ratio ν (nu) is a measure of the Poisson effect. The Poisson ratio is the ratio of the fraction (or percent) of expansion divided by the fraction (or percent) of compression, for small values of these changes.
Dr. Ahmet Zafer Şenalp ME 612
5Mechanical Engineering Department, GTU
2. Definitions2. Definitions
Experiments have shown that in one uni-axial loading strain is composed of two parts• Recoverable elastic strain • Irrecoverable plastic strain.After the elastic limit plastic deformation starts. If a tensile specimen loaded and
extented to a degree defined by point A in Fig. 2.2 is completely unloaded, it recovers some of its extension elastically. AB represents the unloading line.
2.3. 2.3. Elastic Plastic DeformationElastic Plastic Deformation
Dr. Ahmet Zafer Şenalp ME 612
6Mechanical Engineering Department, GTU
2. Definitions2. Definitions
Figure 2.2. Load-extension diagram
Distance BN is recoverable elastic deformation region. Distance OB is permanent plastic deformation region.Elastic Deformation: After unloading returns to zero.Plastic Deformation: After unloading remains at a certain value.
2.3. 2.3. Elastic Plastic DeformationElastic Plastic Deformation
Dr. Ahmet Zafer Şenalp ME 612
7Mechanical Engineering Department, GTU
2. Definitions2. Definitions
Figure 2.3. Engineering stress/strain diagram showing the region of uniform deformation, theinitiation of necking and the post-uniform deformation up to the point of fracture.
2.4. 2.4. The 0.2% yield strengthThe 0.2% yield strength
The 0.2% yield strength is the stress at which a 0.2% permanent offset occurs.This definition simplifies the clarification of yield point for cases without a distinct
transition from elastic to plastic regions (e.g. lower and upper yield points for certain steels, etc.).
Dr. Ahmet Zafer Şenalp ME 612
8Mechanical Engineering Department, GTU
2. Definitions2. Definitions
Figure 2.4. The 0.2% yield strength
2.5. Work Hardening, 2.5. Work Hardening, DuctilityDuctility, Toughness and Hardness, Toughness and Hardness
2.5.1. Work hardening
Work hardening, also known as strain hardening, is the strengthening of a metal by plastic deformation. This strengthening occurs because of dislocation movements within the crystal structure of the material. Metal exceeds elastic region and plastic deformation takes place and strength and hardness values increase in work hardening.
2.5.2. Ductility
Ductility is a mechanical property that describes the extent in which solid materials can be plastically deformed without fracture. Elongation up to rupture is a measure of ductility. How much the elongation, the material is that much ductile.
Opposite of ductile material is brittle material. Ductility is defined as:
Dr. Ahmet Zafer Şenalp ME 612
9Mechanical Engineering Department, GTU
2. Definitions2. Definitions
2.5. Work Hardening, 2.5. Work Hardening, DuctilityDuctility, Toughness and Hardness, Toughness and Hardness
% elongation at fracture :
or using areas as % area reduction at fracture :
Here; :Initial cross section
:Final cross section :Initial length
:Final length
Usually as the strength increases, ductility decreases.Usually as the hardness increases, ductility decreases. To make the material ductile:1. Temperature is increased2. Hydrostatic pressure is increased. Very high hydrostatic pressure delays rupture.
Dr. Ahmet Zafer Şenalp ME 612
10Mechanical Engineering Department, GTU
2. Definitions2. Definitions
0
0
100f x
0
0
100fA Ax
A
0AfA
0f
(2.2)
(2.3)
2.5. Work Hardening, 2.5. Work Hardening, DuctilityDuctility, Toughness and Hardness, Toughness and Hardness
2.5.3 Toughness
The energy needed to bring the material to rupture point is a measure of toughness. Toughness can be determined by measuring the area (i.e., by taking the integral) underneath the stress-strain curve and its energy of mechanical deformation per unit volume prior to fracture. The explicit mathematical description is:
A material cannot be both tough and brittle. 2.5.4 Hardness
Hardness is the resistance to indentation.
Dr. Ahmet Zafer Şenalp ME 612
11Mechanical Engineering Department, GTU
2. Definitions2. Definitions
2.6. 2.6. Fracture TypesFracture Types
A fracture is the (local) separation of an object or material into two, or more, pieces under the action of stress. Fracture is divided into two as ductile and brittle.
Dr. Ahmet Zafer Şenalp ME 612
12Mechanical Engineering Department, GTU
2. Definitions2. Definitions
Figure 2.5. Fracture types in tensile test,(a) Brittle fracture in multi-crystal metals
(b) Ductile shear fracture in uni-crystal metals(c) Ductile cup and cone type fracture in multi-crystal metals
(d) Perfect ductile fracture in multi-crystal metals
2.6. 2.6. Fracture TypesFracture Types
2.6.1. Brittle Fracture
In brittle fracture, no apparent plastic deformation takes place before fracture. In brittle crystalline materials, fracture can occur by cleavage as the result of tensile stress acting normal to crystallographic planes with low bonding (cleavage planes).
Generally low temperature and high strain rate are the encouraging factors for brittle fracture.
In face centered cubic metals generally britlle fracture is not seen. Contrarily to this in body centered cubic and hexagonal closed-packed metals brittle fracture can occur.
Dr. Ahmet Zafer Şenalp ME 612
13Mechanical Engineering Department, GTU
2. Definitions2. Definitions
2.6. 2.6. Fracture TypesFracture Types
Dr. Ahmet Zafer Şenalp ME 612
14Mechanical Engineering Department, GTU
2. Definitions2. Definitions
Figure 2.6. Fracture of an Aluminum Crank Arm. Bright: Brittle fracture. Dark: Fatigue fracture
2.6. 2.6. Fracture TypesFracture Types
2.6.2 Ductile FractureIn ductile fracture, extensive plastic deformation takes place before fracture. The
terms rupture or ductile rupture describe the ultimate failure of tough ductile materials loaded in tension. Rather than cracking, the material "pulls apart," generally leaving a rough surface. In this case there is slow propagation and an absorption of a large amount energy before fracture.
Ductile fracture generally occurs along the planes where shear stress is maximum. Due to its shape ductile fracture is also called as cup and cone type fracture.
Compounds like oxide, sulphur, carbide, silicate cause gaps in metal and alloy which effects ductility and ductile fracture. This fact is not good for the formability of metals.
Dr. Ahmet Zafer Şenalp ME 612
15Mechanical Engineering Department, GTU
2. Definitions2. Definitions
2.6. 2.6. Fracture TypesFracture Types
Dr. Ahmet Zafer Şenalp ME 612
16Mechanical Engineering Department, GTU
2. Definitions2. Definitions
Figure 2.7. Cup and cone type of fracture in tensile test (R.E. Reed-Hill, Physical Metallurgy
Principles, D. Van Nostrand Company, Inc., Princeton, N.J., 1964. p. 555).
2.6. 2.6. Fracture TypesFracture Types
Dr. Ahmet Zafer Şenalp ME 612
17Mechanical Engineering Department, GTU
2. Definitions2. Definitions
Figure 2.8. Ductile failure of a specimen strained axially.
2.7. Hysteresis Effect2.7. Hysteresis Effect
If in the simple tension test the load is removed after the yield stress has been exceeded and then reloading occurs, a hysteresis loop is formed.
Dr. Ahmet Zafer Şenalp ME 612
18Mechanical Engineering Department, GTU
2. Definitions2. Definitions
Figure 2.9. Hysteresis effect
On unloading from a point A, and on reloading from point C, the curves ABC and CDE are initially very nearly parallel to the original elastic loading line. The hysteresis loop is greatly exaggerated on the diagram and, excepting under conditions of continuous cyclic loading, the deformation in the region may be assumed to be elastic, the value of Young's modulus being unaltered by the plastic deformation. OC is the permanent (plastic) strain left in the bar on complete unloading from A.
2.7. Hysteresis Effect2.7. Hysteresis Effect
Dr. Ahmet Zafer Şenalp ME 612
19Mechanical Engineering Department, GTU
2. Definitions2. Definitions
Figure 2.9. Hysteresis effect
On reloading the bar from point C, the reloading line may now be considered linear, yielding occurs at Y' (a larger value than the original yield stress Y) and the curve Y'E becomes virtually a continuation of the curve YA. Note that every point on the continuous curve beyond Y is a yield point.
2.8. Baushinger Effect2.8. Baushinger Effect
When a metal is plastically deformed and then unloaded, residual stresses, on a microscopic scale, are left in the material. This is mainly due to the different states of stress in the variously orientated crystals before unloading. If a metal is plastically deformed in uniform tension as in Fig. 2.10, unloaded and then subjected to uniform compression in the opposite direction, it is found that because of the residual stresses, yielding occurs at a stress Y" which is less than the beginning stress, Y'. This is the Bauschinger effect, and is present whenever there is a stress reversal.
Dr. Ahmet Zafer Şenalp ME 612
20Mechanical Engineering Department, GTU
2. Definitions2. Definitions
Figure 2.10. Baushinger effect
2.9. Engineering Stress, Strain 2.9. Engineering Stress, Strain and True Stress, Strainand True Stress, Strain
2.9.1. Engineering and True Strain
Dr. Ahmet Zafer Şenalp ME 612
21Mechanical Engineering Department, GTU
2. Definitions2. Definitions
Figure 2.11. A part applied tensile force F
F A
ln ln lnF A
dF d dA
F A
(2.4)
(2.5)
(2.6)
At maximum force ( F=Fmax) (At maximum tensile strength)
0dF
F
d dA
A
(2.7)
(2.8)
2.9. Engineering Stress, Strain 2.9. Engineering Stress, Strain and True Stress, Strainand True Stress, Strain
Equation (2.8) shows that at maximum force point the rate of increase of stress is equal to the rate of decrease of area. Here;
A0: Initial cross section
A : Current cross section : Initial length : Current length
Dr. Ahmet Zafer Şenalp ME 612
22Mechanical Engineering Department, GTU
2. Definitions2. Definitions
0
Figure 2.12. Load-extension curve
2.9. Engineering Stress, Strain 2.9. Engineering Stress, Strain and True Stress, Strainand True Stress, Strain
Volume constancy;
Due to volume constancy the term that shows the volume change;
Dr. Ahmet Zafer Şenalp ME 612
23Mechanical Engineering Department, GTU
2. Definitions2. Definitions
0 0V A A
ln ln lnV A dV dA d
V A
0dV
V
dA d
A
(2.9)
(2.10)
(2.11)
(2.12)
(2.13)
2.9. Engineering Stress, Strain 2.9. Engineering Stress, Strain and True Stress, Strainand True Stress, Strain
If (2.8) and (2.13) are equated;
İs obtained. Engineering strain definition:
True strain or logarithmic strain is from (2.14)
Defined differential change in extansion. Equation (2.16) is used in below forms.
Dr. Ahmet Zafer Şenalp ME 612
24Mechanical Engineering Department, GTU
2. Definitions2. Definitions
(2.14)
(2.15)
(2.16)
d dd
0
0
e
dd
0 0
L L
L L
dd
(2.17)0
ln (2.18)
2.9. Engineering Stress, Strain 2.9. Engineering Stress, Strain and True Stress, Strainand True Stress, Strain
Example 1: A tensile test specimen has an initial length of . After the experiment it is assumed that the lenght becomes to 2 . Engineering strain in the experiment is calulated to be;
If the mentioned strecth is achieved in two stages. From to 1,5 and from 1,5 to 2 )
Dr. Ahmet Zafer Şenalp ME 612
25Mechanical Engineering Department, GTU
2. Definitions2. Definitions
(2.19)
Figure 2.13. Uni-axial strain a) Tensile b) Compressive
00
0 0
0
21e
00
00
2.9. Engineering Stress, Strain 2.9. Engineering Stress, Strain and True Stress, Strainand True Stress, Strain
The enginerring strain in first stage;
The enginerring strain in second stage;
is expected howver İs obtained.
This result shows that enginnering strain is not additive.
Dr. Ahmet Zafer Şenalp ME 612
26Mechanical Engineering Department, GTU
2. Definitions2. Definitions
0 01
0
1.50.5e
0 02
0
2 1.50.333
1.5e
1 2 1e e 1 2 0.833e e
(2.20)
(2.21)
2.9. Engineering Stress, Strain 2.9. Engineering Stress, Strain and True Stress, Strainand True Stress, Strain
Example 2: A part witha an initial length L0 is compressed until e=-1 is obtained. To calculate the new length of the part;
is used.
=0 is obtained which is meaningless.
The main problem here is to use engineering strain in large deformation problems.
Dr. Ahmet Zafer Şenalp ME 612
27Mechanical Engineering Department, GTU
2. Definitions2. Definitions
(2.22)
(2.21)
0
0
1e
2.9. Engineering Stress, Strain 2.9. Engineering Stress, Strain and True Stress, Strainand True Stress, Strain
If the above problems are solved by using true strain;Example 1: True strain from to 2 ;
True strain from to 1.5 ;
True strain from 1.5 to 2 ;
and total strain
The sum of strains calculated at two stages is equal to the strain calculated at one stage. In using true strain it is not important in how many satges the deformation takes place. Total strain is obtained by addition of strain in stages.
Dr. Ahmet Zafer Şenalp ME 612
28Mechanical Engineering Department, GTU
2. Definitions2. Definitions
(2.23)
(2.24)
0 0
693.02
ln0
0
0 0
405.05.1
ln0
01
288.05.1
2ln
0
02
(2.25)
693.0288.0405.021
(2.26)
0 0
2.9. Engineering Stress, Strain 2.9. Engineering Stress, Strain and True Stress, Strainand True Stress, Strain
Example 2: ;
is obtained which is a logical number.
Engineering strain is valid within elastic limits and should be used where the strain is less than 1%.
Dr. Ahmet Zafer Şenalp ME 612
29Mechanical Engineering Department, GTU
2. Definitions2. Definitions
(2.27)
1ln0
1
0
e
0368.0
2.9. Engineering Stress, Strain 2.9. Engineering Stress, Strain and True Stress, Strainand True Stress, Strain
It is possible to relate engineering strain and true strain:
By using volume constancy the summation of principal strain is zero;
İn terms of engineering strain;
Dr. Ahmet Zafer Şenalp ME 612
30Mechanical Engineering Department, GTU
2. Definitions2. Definitions
(2.28)
0
0 0
1e
0
1e
0
ln ln( 1)e
ln( 1)e
(2.29)
(2.30)
1 2 3 0
1 2 3(1 )(1 )(1 ) 1e e e
(2.31)
(2.32)
2.9. Engineering Stress, Strain 2.9. Engineering Stress, Strain and True Stress, Strainand True Stress, Strain
2.9.2. Uniaxial Engineering and True Stress
Uniaxial nominal or engineering stress is obtained by dividing force to the original cross-section;
True stress is obtained by dividing force to the current area;
Noth definitions can easly be related;
Dr. Ahmet Zafer Şenalp ME 612
31Mechanical Engineering Department, GTU
2. Definitions2. Definitions
(2.33)
(2.34)
(2.35)
00
F
A
F
A
00 0 0
F F A A
A A A A
2.9. Engineering Stress, Strain 2.9. Engineering Stress, Strain and True Stress, Strainand True Stress, Strain
2.9.3. True Stress-True Strain CurveThere are two ways to find true stress. Either
İs used or using equation (2.35)
calculated from nominal stress value. True strain values is calculated from
or from
Dr. Ahmet Zafer Şenalp ME 612
32Mechanical Engineering Department, GTU
2. Definitions2. Definitions
(2.36)
(2.37)
(2.38)
F
A
00 0 0
0
(1 )A
eA
0
0
ln lnA
A
0
0 0
ln ln 1 ln(1 )e
(2.39)
2.9. Engineering Stress, Strain 2.9. Engineering Stress, Strain and True Stress, Strainand True Stress, Strain
Engineering stress-engineering strain curve has a peak whereas true stress-true strain curve does not have a peak.
This is caused from true stress definition. Force is continuously divided to the current area and area continuously decreases. So stress value continuously increases.
Dr. Ahmet Zafer Şenalp ME 612
33Mechanical Engineering Department, GTU
2. Definitions2. Definitions
Figure 2.14. Comparison of nominal and true stress-strain curves
2.9. Engineering Stress, Strain 2.9. Engineering Stress, Strain and True Stress, Strainand True Stress, Strain
Iın large deformation regions generally elastic deformation can be neglected. In such a graph initial elastic region is invisible and curve starts from yield point Y. (Figure 2.15).
Dr. Ahmet Zafer Şenalp ME 612
34Mechanical Engineering Department, GTU
2. Definitions2. Definitions
Figure 2.15. Elastic deformation in large deforrmation state
2.10. Strain Rate2.10. Strain Rate
The change of strain against time is called as strain rate.
It is possible to define engineering and true strain rate. For this purpose a compression operation is studied.
True strain rate is;
For compression for constant press speed increasing strain rate is obtained. To keep the strain rate at a constant value press speed should be decreased. For tensile operation the reverse is valid.
Dr. Ahmet Zafer Şenalp ME 612
35Mechanical Engineering Department, GTU
2. Definitions2. Definitions
d
dt
/ 1dH H dH V
dt H dt H
(2.40)
(2.41)
2.10. Strain Rate2.10. Strain Rate
Like true strain rate engineering strain rate can be defined;
The above extraction cannot be obtained with engineering strain rate.
Dr. Ahmet Zafer Şenalp ME 612
36Mechanical Engineering Department, GTU
2. Definitions2. Definitions
(2.42)
Figure 2.16. Compresive force application to a part with initaial height H
0
0 0
/ 1dH H dH Ve
dt H dt H
2.10. Strain Rate2.10. Strain Rate
The average strain rate obtained during the operation can also be calculated;Average strain rate is calculated as;
Here;h : Height at the end of operation,V0: Initial press speed,
H0: Initial height
T : Time needed for completion of compression operation.
Dr. Ahmet Zafer Şenalp ME 612
37Mechanical Engineering Department, GTU
2. Definitions2. Definitions
(2.43)
0 0 0 0
0 0 0( ) /( / 2) 2( )
V
T H h V H h
0
0
0
ln
2 ( )
HhV
H h
(2.44)
2.10. Strain Rate2.10. Strain Rate
Average engineering strain rate is;
Strain rate sensitivity is higher in high temperature. The effect of increase of strain rate to the stress-strain curve is less than temperature effect.
Dr. Ahmet Zafer Şenalp ME 612
38Mechanical Engineering Department, GTU
2. Definitions2. Definitions
(2.45)
(2.46)
0 0 0 0
0 0 0 0
( ) /
( ) /( / 2) ( ) /( / 2)
e e H h He
T H h V H h V
0
02
Ve
H
2.11. Ideal Work Method2.11. Ideal Work Method
Every solution method is based on certain assumptions. The easiest method is ideal work method. The work needed to deform workpiece is equated to the external work done. The process in which the external work is completely used in deformation is called ideal process. It is assumed that there is no friction and deformation is homogenous.
In Figure 2.17 ideal compression operation is shown with initial and final stages. Vertical and horizontal line do not change shape during operation. This is a result of homogenous deformation.
Dr. Ahmet Zafer Şenalp ME 612
39Mechanical Engineering Department, GTU
2. Definitions2. Definitions
Figure 2.17. Uniform ideal deformasyon
2.11. Ideal Work Method2.11. Ideal Work Method
In reality the deformation is not homogeneous and with progressing compression barreling effect is observed. (Figure 2.18)
Dr. Ahmet Zafer Şenalp ME 612
40Mechanical Engineering Department, GTU
2. Definitions2. Definitions
Figure 2.18. Barrelling effect observed in real deformation
2.11. Ideal Work Method2.11. Ideal Work Method
F=AYF: Applied forceA: Current cross sectionY: Yield StrenghtH0: Initial height
H: Current heightVolume constancy; V= A0 H0=AH
Dr. Ahmet Zafer Şenalp ME 612
41Mechanical Engineering Department, GTU
2. Definitions2. Definitions
Figure 2.19. Compression process
(2.47)
2.11. Ideal Work Method2.11. Ideal Work Method
dW=F(-dH)
For ideal plastic deformation the work done per unit volume; w;
Dr. Ahmet Zafer Şenalp ME 612
42Mechanical Engineering Department, GTU
2. Definitions2. Definitions
0 0A HA
H (2.48)
0 0A H YF
H
0 0
0lnH H
c
H H
HdHd
H H
(2.49)
(2.50)
(2.51)
0 0 ( )A H Y
dW dHH
0
00 0 0 0 ln
H
H
HdHdW A H Y A H Y
H H
(2.52)
(2.53)
0ln c
HWw Y Y
V H
(2.54)
2.11. Ideal Work Method2.11. Ideal Work Method
If instead of yield point an arbitrary stress-strain point is considered, instead of Y, can be replaced. If not only compression but a general operation state is consideredcan be replaced with ;
The work done per unit volume for ideal plastic deformation is obtained. The area under stress-strain curve yields the work done per unit volume.
Dr. Ahmet Zafer Şenalp ME 612
43Mechanical Engineering Department, GTU
2. Definitions2. Definitions
(2.55)
c
w
Figure 2.20. Tension operation and the area under stress-strain curve.
2.11. Ideal Work Method2.11. Ideal Work Method
Specific forming energy is called as u;
This calculated ideal work does not include friction and redundant shear effects.
These effects and efficiency criteria will be covered in the chapter related with ideal work.
Dr. Ahmet Zafer Şenalp ME 612
44Mechanical Engineering Department, GTU
2. Definitions2. Definitions
(2.56) u w