2 1 3 ZXSDR BS8700 Product Description

7/30/2019 2 1 3 ZXSDR BS8700 Product Description

1/41

Volume IV Section 2 Chapter 2.3ZXSDR BS8700 Product Description


2/41

ZXSDR BS8700 Product Descrip!ion

ZXSDR B8700 Product Description

Version Date Author Approved By Remarks

V4.1 2011-01-15

ZTE Confidential Proprietary 2011 ZTE Corporation. All rights reserved. I

2010 ZTE Corporation. All rights reserved.

ZTE CONFIDENTIAL:This document contains proprietary information of ZTE and is not to bedisclosed or used without the prior written permission of ZTE.

Due to update and improvement of ZTE products and technologies, information in this document issubjected to change without notice.


3/41


TABLE OF CONTENTS

1 Overview 1

2 Product Highlights.....................................................................................................................3

3 Functionality...............................................................................................................................43.1 Basic Functions.........................................................................................................................43.2 Service Functions......................................................................................................................5

4 System Architecture..................................................................................................................74.1 Product Physical Structure........................................................................................................7

4.2 Hardware Architecture..............................................................................................................74.2.1 Baseband Unit.................................................................................................................... 94.2.2 Radio Unit......................................................................................................................... 164.3 Software Architecture..............................................................................................................224.4 External Interface...................................................................................................................23

5 Technical Indices.....................................................................................................................24

6 Operation and Maintenance....................................................................................................26

7 Configuration Principles..........................................................................................................297.1 Baseband Unit Configuration Principles..................................................................................297.2 Radio Unit Configuration Principles.........................................................................................29

7.3 GSM Single Mode Configuration Principles............................................................................307.3.1 R8860/R8860E configuration ............................................................................................307.4 UMTS Single Mode Configuration Principles..........................................................................307.4.1 R8840/R8880 configuration ..............................................................................................307.4.2 R8860/R8860E configuration ............................................................................................317.4.3 R8890 configuration ..........................................................................................................317.5 GSM/UMTS Dual Mode Configuration Principles....................................................................317.5.1 GSM 850M/900M/1800M/1900M and UMTS 850M/900M/1800M/1900M Dual-Mode

Network in Same Spectrum ....................................................................................317.5.2 GSM 850M/900M/1800M/1900M and UMTS 2100M Dual-Mode Network in Different

Spectrums ..............................................................................................................32

8 Acronyms and Abbreviation...................................................................................................33

35

II 2011 ZTE Corporation. All rights reserved. ZTE Confidential Proprietary


4/41


FIGURES

ZTE Confidential Proprietary 2011 ZTE Corporation. All rights reserved. III


5/41


Conventional GSM/EDGE/UMTS Network System.....................................................................1

ZTE SDR BS Composed GSM/UMTS Network............................................................................1

Networking Diagram (B8200, RNC/BSC and RRU).....................................................................2

In chain and loop networking mode, 4 RRU can be maximally cascaded and the maximaldistance is 100 Km; The maximal distance between BBU and first RRU can reach 40 Km.Usually its kindly suggested no more than 10 Km....................................................................2

Example of ZXSDR BS8700 Physical Structures........................................................................7

BS8700 Hardware Structure ........................................................................................................8

Baseband Unit of BS8700.............................................................................................................9

CC Panel 9

UBPG Panel.................................................................................................................................11

BPC Panel 11

FS Panel. 12

SA Panel 13

SE Panel 13

NIS Panel. 14

PM Panel 15

FAM Panel 15

R8840 Physical Appearance.......................................................................................................16

R8840 External Interfaces..........................................................................................................17

R8860/R8860E Physical Appearance.........................................................................................18

R8860/R8860E External Interfaces.............................................................................................18

R8880 Physical Appearance.......................................................................................................19


R88890 Physical Appearance.....................................................................................................21


BS8700 Software Structure........................................................................................................22

NetNumen M31 Elements Management System.......................................................................26

IV 2011 ZTE Corporation. All rights reserved. ZTE Confidential Proprietary


6/41


TABLES

Mechanical Sizes of ZXSDR BS8700...........................................................................................7

Main Board List of Baseband Unit...............................................................................................9

Table of CC Panel Interfaces......................................................................................................10

Table of FS Panel Interfaces .....................................................................................................12

Table of SA Panel Interfaces......................................................................................................13

Table of SE Panel Interfaces .....................................................................................................14

Table of NIS Panel Interfaces.....................................................................................................14

Table of PM Panel Interfaces .....................................................................................................15

R8840 External Interface............................................................................................................17

Description of External interfaces.............................................................................................18



Description of ZXSDR BS8700 External Interfaces..................................................................23

ZXSDR BS8700 Technical Indices.............................................................................................24

ZXSDR BS8700 Configuration for GSM Single Mode (Multi-carrier).......................................30

ZXSDR BS8700 Configuration UMTS Single Mode (R8840/R8880).........................................30

ZXSDR BS8700 Configuration UMTS Single Mode (R8860/R8860E).......................................31

ZXSDR BS8700 Configuration UMTS Single Mode .................................................................31

BS8700 Configuration for G/U Dual-Mode (Same Spectrum)..................................................31

BS8700 Configuration for G/U Dual-Mode (Different Spectrums)..........................................32

ZTE Confidential Proprietary 2011 ZTE Corporation. All rights reserved. V


7/41


1 Overview

In general, GSM/EDGE/UMTS system consists of Core Network (CN), Radio Network(GERAN/UTRAN) and Mobile Station/User Equipment (MS/UE). GERAN/UTRANincludes 2 network elements, base station and BSC/RNC. The conventional 2G/3G BSconnects to BSC/RNC via Abis/Iub interface. Figure 1 shows a conventionalGSM/EDGE/UMTS network system.

Figure 1 Conventional GSM/EDGE/UMTS Network System

In Figure 1, GPRS/EDGE and UTRAN are two separated radio networks. When ZTE2G/3G dual-mode base station is introduced, the 2G/3G radio networks will beconverged into one and this will decrease the network construction cost greatly. TheGSM/UMTS integrated network is shown in the following Figure 2.

Figure 2 ZTE SDR BS Composed GSM/UMTS Network

ZTE Confidential Proprietary 2011 ZTE Corporation. All rights reserved. 1

BS

BSC

2G BSS Only

Node B

Node B

RNC

RNC

HLR

PSTN

IP Network

MGW MSCS

SGSN GGSN

3G UTRAN Only

GSM MS

UMTS UE

SDR BS

SDR BS

BSC/RNC

HLR

PSTN

IP Network

MGW MSCS

SGSN GGSN

Software Defined Radiofor both G/U systems

BSC/RNC

SDR BS flexibly configured as a GSMand UMTS system with only softwareconfiguration

GSM MS

UMTS UE


8/41


The purpose of this document is to describe the new-generation distributed SoftwareDefined Radio (SDR) base station ZXSDR BS8700 (hereafter BS8700), which consistsof the core BBU (B8200) and series RRUs. BS8700 is based on the ZTE unifiedMicroTCA platform and adopting MCPA technology radio part, to be the new type of ZTE

mobile BS. This revolutionary BS platform supports all kinds of wireless accesstechnology including GSM, UMTS, CDMA2000 WiMAX and LTE.

ZXSDR BS8700 can be divided into different types of distributed BS through connectingwith different RRUs, according to different networking modes and coverage scenarios.

B8200+R8860/R8860E: Dual mode macro distributed base station, mainly used for outdoor

and indoor GSM/UMTS dual mode coverage.

B8200+ R8840/R8880/R8890: UMTS mode macro distributed base station, mainly used for

outdoor and indoor UMTS mode coverage.

B8200 provides Iub/Abis interfaces with several types of physical interface such asE1/T1, STM-1, FE and GE to connect with RNC/BSC and CPRI interfaces to connectwith RRUs. B8200 supports IP transmission and hybrid transport. B8200 provides atmost 12 pairs of CPRI optical interfaces to RRUs.

B8200 and RRU can support!star, chain and mixed networking. In star networking, 12optical interfaces can connect to 12 RRUs. In chain networking, RRU can cascade up to4 levels.

The networking diagram including B8200, RNC/BSC and RRU is shown in .

Figure 3 Networking Diagram (B8200, RNC/BSC and RRU)

In chain and loop networking mode, 4 RRU can be maximally cascaded and the maximaldistance is 100 Km; The maximal distance between BBU and first RRU can reach 40Km. Usually its kindly suggested no more than 10 Km.

2 2011 ZTE Corporation. All rights reserved. ZTE Confidential Proprietary

FE/GE


9/41


In the following chapter, a general description will be given to GSM/UMTS dual modeBase Station ZXSDR BS8700.

2 Product HighlightsZXSDR BS8700 (hereafter BS8700) is the multi-carrier, dual-mode distributed basestation of ZXSDR BS series. By adopting advanced MicroTCA platform and SDRtechnology, BS8700 can support!GPRS/EDGE/E-EDGE and UMTS/HSPA/HSPA+simultaneously. In the future evolution to LTE, only change baseband processing boardand software upgrade. Its main advantage is the flexibility which brings the possibility tosupport!GSM and UMTS on a single base station.

Compared with traditional base station, ZXSDR BS8700 has following highlight features:

Series RRUs, suitable for multi indoor and outdoor coverage scenarios.

Series RRUs with high output power, including R8840, R8860/R8860E, R8880 and

R8890.

RRU - Compact Design, Light, Easy Installation

RRU (R8840) is only 19 liters in volume and 16.5kg in weight under typical power

output. It can be mounted on the pole, the wall, the tower top, etc. Natural cooling

without fan. No dedicated equipment space is required, easy for site selection, fast

network deployment.

RRU Installed Near Antenna, Saving Feeder Loss, Enhancing Coverage

Series RRU can be remotely installed near the antenna system to lower the feeder

loss. The coverage gain can reach more than 3dB compared with traditional macro

base station.

BBU - Plug-in Design for Shelf, Zero Footprint, Convenient Deployment

B8200 adopts Plug-in design with 19 inch, 2U in height and 8.75 kg in weight. It can

be conveniently mounted on the wall, ground, or in the 19 inch rack, etc.

Shared Baseband Resources, Dynamic Traffic Adjustment

Suitable for traffic transferring dynamically or outburst areas, such as CBD, uptown

or beauty spots, avoiding resources waste.

Various Interfaces, Flexible Networking

ATM/IP dual protocol stacks, providing with various interfaces such as E1/T1/STM-

1/GE etc. It supports SDH networking, hybrid transmission and all-IP networking.

G/U dual-mode Configuration, Smoothly Evolve to Future Network

Supports GSM/GPRS/EDGE/ E-EDGE/UMTS/HSPA/HSPA+.

Multi-Carriers and Multi-Frequencies



10/41


R8860/R8860E has the capability to support!6 GSM TRX or 4 UMTS carriers. If

GSM and UMTS are configured at the same spectrum, each radio unit supports 4

GSM TRX + 1 UMTS carrier.

3 Functionality

3.1 Basic Functions

BS8700 supports the following basic functions on Um/Uu, Abis/Iub and O&M interfaces.

On Um/Uu interface, BS8700 supports UE access and radio link transmission including RF

processing, channel coding and decoding, channel multiplexing and de-multiplexing,

measuring and reporting, power control, transmit diversity, receiving diversity, calibration andsynchronization.

Via Abis/Iub interface, BS8700 connects with BSC/RNC and supports the following functions

including cell management, BS measurement information report, system Information

broadcast, access control implementation from BSC/RNC, mobility management, radio

resource management and control, FP process and ATM transmission management.

On operating and maintenance interface, BS8700 provides system management functions

including configuration management, alarm management, status check and system monitor.

Besides, BS8700 provides following functions:

Supports GSM Phase I/GSM Phase II/GSM Phase II plus standards.

Supports 3GPP R99, R4, R5, R6, R7, R8.

Supports GSM/UMTS 900MHz, EGSM 900MHz, GSM/UMTS 850MHz GSM/UMTS

1800MHz, GSM/UMTS 1900MHz, UMTS 2100MHz.

BS8700 supports GSM channel spacing at least 200KHz, and supports UTMS working on

bandwidth at least 3.8MHz and WCDMA/LTE 20MHz.

Supports socket-independent boards installation to support!different frequencies in the same

cabinet.

Supports CS1~CS4 of GPRS, MCS1~MCS9 of EDGE.

Supports reduced TTI, fast ACK/NACK reporting, MS receive diversity, downlink dual carriers

and EGPRS2-A of E-EDGE.

Supports dynamically changing channel coding according to monitoring and measurement

results.

Supports space diversity, frequency diversity, time diversity, polarization diversity and

maximum ratio combination diversity.



11/41


The receiving part adopts Viterbi algorithm for coding to improve Channel decoding capability

and system receiving sensitivity.

Supports frequency hopping.

Supports DTX sending and decreasing transmitting power, lowering the total interference in

the air.

Supports common BCCH; different carriers can be used for different services and they share

the same BCCH.

3.2 Service Functions

BS8700 supports the following services:

GSM/GPRS/EDGE/E-EDGE:

FR: Full Rate voice service

EFR: Enhanced Full Rate voice service

HR: Half Rate voice service

AMR: Adaptive Multi Rate voice service

F9.6: 9.6Kbit/s CS domain data service

GPRS/EDGE/E-EDGE

Location service:

Support!Cell ID, Cell ID+RTT and AGPS location services

R99 service:

CS domain service: 8 Kinds of AMR voice service, CS 64Kbps

PS domain service: UL/DL 64Kbps, UL/DL 128Kbps, UL/DL 384Kbps

Concurrent service: CS domain (AMR 12.2Kbps, CS 64Kbps) + PS domain(64Kbps, 128Kbps, 384Kbps)

HSDPA Service:

Support!Data rate 14.4Mbps

Support!15 codes

Support!HSDPA and R99 on both independent and shared carriers



12/41


Support!intra-frequency, inter-frequency handover and handover betweenHSDPA and R99

Support!concurrent services

Support!streaming services

HSUPA Service:

Supporting 5.76Mbps uplink data rate

MBMS Service:

Support!broadcast and multicast functions, multicast supports PtP and PtM

Support!mobility management

Support!streaming, background MBMS services

HSPA+ Service:

21.6Mpbs Downlink data with 64QAM

28.8Mpbs Downlink data with 16QAM + 2*2 MIMO

43.2Mpbs Downlink data with 64QAM + Dual Cell combination



13/41


4 System Architecture

4.1 Product Physical Structure

ZXSDR BS8700 consists of the BBU (B8200) and series of RRUs. The physicalstructures of ZXSDR BS8700 in different combinations are shown in :

Figure 4 Example of ZXSDR BS8700 Physical Structures

Mechanical sizes of ZXSDR BS8700 in different combinations are shown in following .

Table 1 Mechanical Sizes of ZXSDR BS8700

Mechanical

Size

Height

(mm)

Width

(mm)

Depth

(mm)

Weight (Kg)

B8200 88.4 482.6 197 8.75

R8840 370 320 160 16.5

R8860/R8860E 370 320 197 20

R8880 420 340 140 20

R8890 385 452 155 28

4.2 Hardware Architecture

BS8700 hardware architecture is shown in .



14/41


Figure 5 BS8700 Hardware Structure

The BBU of ZXSDR BS8700 can be configured in GSM/UMTS single mode and G/Udual-mode. It supports up to 30 CS in UMTS single mode, providing 1920 CE base-bandprocessing capability DL/UL separately, up to 60 TRX in GSM single mode.

There are 4 kinds of ZXSDR BS8700 RRUs:

R8840 2 receiving paths and 1 transmitting path (1T2R). Each one can support!1

sector in UMTS on 2100MHz/AWS. Its output power achieves 60W (TOC). It is

mainly used for outdoor macro coverage and also used for indoor coverage signal

source. R8840 can support!3 carriers when it ensures 20W output power for each

carrier.

R8860/R8860E 2 receiving paths and 1 transmitting path (1T2R). Each one can

support!1 sector in GSM/UMTS on 850/900/1800/1900MHz. Its output power

achieves 80W (TOC). It is mainly used for outdoor macro coverage and also used

for indoor coverage signal source. R8860/R8860E can support!4 carriers when it

ensures the 20W output power for each carrier.

R8880 2 receiving paths and 2 transmitting paths. Each one can support!2*2

MIMO in HSPA+ mode on 2100MHz. Its output power achieves up to 2*60W (TOC).

It is mainly used for outdoor macro coverage and also used for indoor coverage

signal source. R8880 can be configured as UMTS mode. R8880 can support!3

carriers when it ensures the 2*20W output power for each carrier.

R8890 6 receiving paths and 3 transmitting paths (3T6R). Each one can support!3

sectors in UMTS mode on 2100MHz. Its output power achieves up to 3*60W (TOC).

It is mainly used for outdoor macro coverage and also used for indoor coverage

signal source. R8890 can support!3 carriers 3 sectors when it ensures 20W output

power for each CS.


Baseband Unit

Radio Unit

SA/SE/NIS

CC

BB(UBPG/BPC)

FS RRU

E1

GE/FE

Clock

Data

Control Signaling

CPRI

Antenna

RF Unit

STM-1


15/41


4.2.1 Baseband Unit

Baseband unit in BS8700 is responsible for processing the baseband signals.

Figure 6 Baseband Unit of BS8700

The Baseband unit consists of control & clock board, fabric switch board, basebandprocessing board, site alarm board (optional), site alarm extension board, networkInterface of STM-1 board (optional), power module, and fan module.

Table 2 Main Board List of Baseband Unit

Board Name Function Description

CC Control & Clock Board

FS Fabric Switch Board

UBPG Universal Baseband Processing board for GSM

BPC Base band Processing Board Type C for UMTS

SA Site Alarm Board

SE Site alarm Extension Board

NIS Network Interface of STM-1 Board

PM Power Module

FAM FAN Module

4.2.1.1 Control & Clock Board (CC)

CC is control and clock board, used for control and management of baseband unit,providing Ethernet and system clock. The CC panel is illustrated in 4.2.1.

Figure 7 CC Panel

Description of CC panel interfaces is shown in 4.2.1.


PM

SA

CC

FSS UBPG/BPC

FAM


16/41


Table 3 Table of CC Panel Interfaces

Interface Name Description

ETH0 Ethernet interface between BS8700 and BSC/RNC, adapting interface of 10M/100M/1000M.

ETH1 Ethernet interface used for cascading, debugging or local maintenance,adapting interface of 10M/100M/1000M.

TX/RX Used for Ethernet interface connection between BS8700 and BSC/RNC. Thisinterface is 100M/1000M Ethernet optical interface.

EXT External communication port, connected to external receiver,Mainly 485PP1S+/2M+ interfaces.

REF External connection GPS antenna, SMA(F) interface

Control & clock board functions are as follows:

Ethernet switching function, implementing data switching for service and control flow within

the system

Abis/Iub interface protocol processing

Monitoring, controlling and maintaining of the base station system, providing LMT interface

Managing software versions of boards and programmable components, and supporting local

and remote software upgrade

Supervising the running status of each board within the system

Synchronizing with various external reference clocks, including the Abis/Iub interface

recovery clock, the GPS clock and the clock provided by BITS; The CS can select one

according to the actual configuration.

Generating and delivering the clock signal demanded by each part

Providing GPS receiver interface and managing the GPS receiver

Providing a real-time clock for system operation and maintenance; the real-time clock can be

calibrated

The board power interface (-48V, -48V ground, protection ground, digital ground) has reverse

connection protection function

Reading various hardware management marks in the system, including the rack number,

backplane type number, slot number, board function type, board version, and board function

configuration mark

Supporting Control & Clock boards load sharing or primary/slave switchover. The load

sharing and primary/slave switchover mode can be set by software configuration.

4.2.1.2 UBPG Board

UBPG is the GSM baseband processing board. It processes the physical layer protocoland frame protocol specified by 3GPP. UBPG panel is illustrated in 4.2.1.



17/41


Figure 8 UBPG Panel

UBPG main function as follows:

Achieving rate adaptation, channel coding, interleaving, encryption, generate TDMA shock

burst, GMSK/8PSK modulation, IQ baseband digital signals output.

Achieving uplink IQ data receiving, receiver diversity combiner, digital demodulation

(GMSK&8PSK, equilibrium), decryption, deinterleaving, demodulator, rate adaptation, GE

Ethernet interface transmit it to CC board for processing.

Radio link synchronization, transmission frame processing

Measuring parameters required in power control and handover

Diversified transmission and receiving

Communicating with CS via Ethernet interface

Reading all the hardware management identifiers, including the backplane type number, slot

number, board function type, board version, board function configuration identifier, and the

CPU serial number.

4.2.1.3 BPC Board

BPC is the UMTS baseband processing board. It processes the physical layer protocoland frame protocol specified by 3GPP. BPC panel is illustrated in 4.2.1.

Figure 9 BPC Panel

BPC hasnt external interface, its main function as follows:

Achieving downlink baseband signal processing, including downlink data coding,

multiplexing, rate adaptation, channel mapping, spread spectrum and scrambling

power regulation and channel compositing.

Achieving uplink baseband signal processing, including uplink data RAKE receiving,

demodulator, transmitting the data to lub interface for processing.



18/41


Downlink data coding/multiplexing, rate matching, channel mapping, spreading and

scrambling, power adjusting, and channel compositing.

Uplink signal RAKE receiving and channel decoding

Radio link synchronization and Frame processing

Measuring parameters required in power control and handover

Softer handover and carrier diversity.

Communicating with the CS via the Ethernet interface

Reading all the hardware management identifiers, including the backplane type number, slot

number, board function type, board version, board function configuration identifier, and the

CPU serial number

4.2.1.4 Fabric Switch Board (FS)

FS is fabric switch board which provide baseband optical interface between BBU andRRU and process the IQ signal, and provide CPRI interfaces to connect with RRUs. FSpanel is illustrated in 4.2.1.

Figure 10 FS Panel.

Description of FS panel interfaces

Table 4 Table of FS Panel Interfaces


TX0 RX0TX5 RX5 6 pairs optical interfaces, connected to RRU

The FS has the following functions:

Receive the signal from the rear board in the downlink and retrieve the data and timing.

Multiplex the received data and retrieve I/Q signal

I/Q mapping in the downlink and multiplex I/Q signal to the optical signals.

Receive the I/Q in uplink and demultiplex/mapping into I/Q signal

The multiplexed I/Q signal transmit to BP



19/41


Exchange CPU interface signaling through HDLC interface with RU module

MicroTCA protocol based module management function

4.2.1.5 Site Alarm Board (SA)

SA is a site alarm board, illustrated in 4.2.1.

Figure 11 SA Panel

Description of SA panel interface is shown in Table 5.

Table 5 Table of SA Panel Interfaces


-8 E1/T1 interfaces,

1 RS485,

1RS232 interface,

6+2 dry contacts ( 6 input interfaces, 2 input&output interfaces )

The SA has the following functions:

Provide E1/T1 transmission interfaces for Iub.

Provide site alarm monitoring interfaces.

Provide FAM's alarm and rate control.

4.2.1.6 Site alarm Extension Board (SE)

SE is site alarm extension board, and SE panel is illustrated in 4.2.1.

Figure 12 SE Panel

Description of SE panel interfaces is shown in Table 6.



20/41


Table 6 Table of SE Panel Interfaces


-

8 E1/T1 interfaces,

1 RS485,1RS232 interface,

6+2 dry contacts ( 6 input interfaces, 2 input&output interfaces )

SE shares the bottom-right slot with UBPG/BPC and has the following functions:

Provide E1/T1 transmission interfaces for Iub.

Provide site alarm monitoring interfaces.

It is used to extend the port number if SA can not fulfill the requirements.

4.2.1.7 Network Interface of STM-1 board(NIS)

NIS is STM-1 network interface board, and NIS panel is illustrated in 4.2.1.

Figure 13 NIS Panel.

Description of NIS panel interfaces is shown in Table 7.

Table 7 Table of NIS Panel Interfaces


- 2 STM-1

The NIS has the following functions:

2 STM-1fiber interfaces, support!spending processing, mapping and mapping solutions,space-division overlapping, support!21 E1 or 28 T1 most greatly to the STM-1 mapping.

Support!the ADM/TM working.

Support!the AU3/AU4 mapping way.

Support the APS protection function.

4.2.1.8 Power Module (PM)

PM is power module, and PM panel is illustrated in 4.2.1.



21/41


Figure 14 PM Panel

Description of PM panel interface is shown in 4.2.1.

Table 8 Table of PM Panel Interfaces


MON Debugging interface, RS232 interface

-48V/-48VRTN -48V input

The PM has the following functions:

16 internal interfaces for +12 V load power;

16 internal interfaces for +3.3 V management power;

EMMC management;

Measurement and protection of input over-voltage/under-voltage;

Output over-current protection and load power management.

4.2.1.9 Fan Array Module (FAM)

FAM is fan array module which panel is illustrated in 4.2.1.

Figure 15 FAM Panel



22/41


The FAM main functions are as follows:

System temperature monitor and control;

Monitor, control, and report!of fan state.

4.2.2 Radio Unit

Radio unit main process the conversion between baseband signals and RF signals.

In the BS8700, radio unit has four kinds, respectively are: R8840, R8860/R8860E,R8880 and R8890. R8840 is the UMTS only radio frequency module, which works inUMTS on 2100MHz. R8860/R8860E is the multi-carrier radio frequency module, whichcan work in GSM only, UMTS only or G/U dual mode via software configuration. R8880is the UMTS only radio frequency module, and each module supports 2*2 MIMO in

UMTS mode on 2100MHz. R8890 is UMTS only radio frequency module, which support!3 sectors on 2100MHz. The following will show the details.

In the BS8700, CFR(Crest Factor Reduction)algorithm, DPD(Digital Pre-Distortion)algorithm and Advanced-Doherty PA technique are adopted to improve PA linearity andEVM/RCDE performance, the output power is not affected by modulation mode.

4.2.2.1 R8840

R8840 is a UMTS multi-carrier radio unit, working on 2100MHz/AWS, supportingupgrade to LTE via software upgrade. R8840 supports maximum 4 carriers, the outputpower is 60W. R8840 module consists of MCPA (multi-carrier power module) module,

transceiver module, duplex filter LNA and RPWAC/DC (Power for AC or DC). There areone TX/RX port!and one RX port!for connecting antenna. R8840 employs compactcabinet design, as shown in Figure 16. Dimension of R8840 is 370320160mm(HWD).

Figure 16 R8840 Physical Appearance

The external interfaces of R8840 system are integrated at the bottom of the equipment,as shown in Figure 17. The interface description is shown in the following table.



23/41


Figure 17 R8840 External Interfaces

Table 9 R8840 External Interface

S.N. Label Interface Interface Type / Connector

1 LC1 BBU and RRU Interface/RRU cascading interface

LC-mode optical interface (IEC 874)



3 AISG AISG interface 8-core aerial socket (IEC 60130-9-ED)

4 Monitor External device interface 37-pin aerial socket

5 PWR Power supply interface AC interface: Connector XCE18T3K1P1-02+FJJP1-7.5Cable section area: 3*1mm2

DC interface: ConnectorXCG18T4K1P1-01+XC18FJJP1-10.5Cable section area: 4*1.5mm2

6 RX Interface to receive diversityRF cable

50 N-mode connector

7 RX/TX Interface to transmit / receivemain diversity RF cable

50 N-mode connector

8 RXout Frequency extensioninterface

N-KY (MIL-C-39012 or IEC169-16)

9 RXin Frequency extensioninterface

N-KY (MIL-C-39012 or IEC169-16)

10 GND Equipment grounding Cable section area: 16mm2

4.2.2.2 R8860/R8860E

R8860/R8860E is multi-carrier RF module, working on 850/900/1800/1900MHz,supporting upgrade to LTE via software upgrade. R8860/R8860E can be configured asGSM only, UMTS only or mixed mode module. R8860/R8860E can be configured to 1 to6 TRX in GSM mode. In case of GMSK modulation, 80W TOC output power can beprovided. If R8860/R8860E is used as UMTS mode, it can support!4 carriers with 80W



24/41


TOC output power. In mixed mode, R8860/R8860E can support!4 GSM TRX and 1UMTS carriers or 2 GSM TRX and 2 UMTS carriers.

R8860/R8860E module consists of MCPA module, transceiver module, and duplex filter

LNA. There are one TX/RX port!and one RX port!for connecting antenna.R8860/R8860E employs compact cabinet design, as shown in Figure 18. Dimension ofR8860/R8860E is 370320197 mm (HWD).

Figure 18 R8860/R8860E Physical Appearance

R8860/R8860E external interface locates at the bottom of the cabinet, as shown in4.2.2. The interface description is shown in Table 10.

Figure 19 R8860/R8860E External Interfaces

Table 10 Description of External interfaces




2 LC2 BBU and RRU Interface LC-mode optical interface (IEC 874)



25/41



/RRU cascading interface


4 Mon External device interface 37-pin aerial socket5 PWR Power supply interface DC interface:

Connector XCG18T4K1P1-01+XC18FJJP1-10.5

Section area of cable is 4*1.5mm2


50 DIN-mode connector



8 RXout Frequency extensioninterface

N-KY (MIL-C-39012 or IEC169-16)

9 RXin Frequency extension

interface

N-KY (MIL-C-39012 or IEC169-16)


4.2.2.3 R8880

R8880 is a multi-carrier RF module. R8880 can be configured as UMTS mode,supporting upgrade to LTE via software upgrade. It can process 2 received signals and2 transmitted signals. Each one can support!2*2 MIMO in HSPA+ mode on 2100MHz. Itsoutput power achieves up to 2*60W (TOC). It is mainly used for outdoor macro coverageand also used for indoor coverage signal source. R8880 can be configured as UMTSmode. R8880 can support!3 carriers when it ensures the 2*20W output power for each

carrier.

R8880 employs compact cabinet design, as shown in the following figure. R8880 is 420340140 mm (HWD) and 20Kg in weight.


R8880 external interface locates at the bottom of the cabinet, as shown in the followingfigure. The interface description is shown in the following table.



26/41





1 OP1 BBU and RRU Interface/RRU cascading interface


2 OP2 BBU and RRU Interface/RRU cascading interface


3 AISG AISG interface 8-core aerial socket (IEC 60130-9-ED)4 Mon External device interface 37-pin aerial socket

5 PWR Power supply interface DC interface:



6 ANT1(TX1/RX1) Interface to transmit/receivediversity RF cable


7 ANT2(TX2/RX2) Interface to transmit / receivediversity RF cable



4.2.2.4 R8890

R8890 is a multi-carrier RF module. R8890 can be configured as UMTS mode,supporting upgrade to LTE via software upgrade. It processes 6 received signals and 3transmitted signals. Each one can support!3 sectors in UMTS mode on 2100MHz. Itsoutput power achieves up to 3*60W (TOC). It is mainly used for outdoor macro coverageand also used for indoor coverage signal source. R8890 can support!3 carriers 3 sectorswhen it ensures the 20W output power for each carrier.

For the available time of R8890, please refer to .


1 2 3 4 5

6 7 8


27/41


R8890 employs compact cabinet design, as shown in the following figure. R8890 is 385452155mm (HWD) and 28Kg in weight.


R8890 external interfaces locate at the bottom of the cabinet, as shown in the followingfigure. The interface description is shown in the following table.









4 Mon External device interface 37-pin aerial socket



28/41











9 RX/TX Interface to receive diversityRF cable


10 RX Interface to transmit / receivemain diversity RF cable


11 PWR Power supply interface DC interface:



4.3 Software Architecture

The software system of BS8700 consists of operating support!layer and applicationlayer.

Figure 24 BS8700 Software Structure

The operating support!layer provides the functions of OAM, DBS, BRS, BRACS, andSCS to serve different base station mode.

OAM (Operating and Maintenance) provides the configuration, alarm and

performance measurement function.



29/41


DBS (Data Base Sub-system) provides the database function.

BRS (Bearer Sub-system) provides protocol stack processing function.

BRACS (Bearer Access Control Sub-system) provides the function of access

control on bear layer.

SCS (System Control Sub-system) provides functions of power control/supply and

active/standby switching.

Operation Support!Sub-system is the support!layer in this framework, which is ahardware independent platform for running software and providing basic functions likescheduling, timer, memory management, communication, sequencing control,monitoring, alarming and logging.

BSP (Board Support!Package) supports the information routing to the GSM, UMTS, LTEand common parts in the application layer.

4.4 External Interface

ZXSDR BS8700 has abundant external interfaces which are described in Table 3.

Table 13 Description of ZXSDR BS8700 External Interfaces

Interface Item IndexInterfaceType

Standard

Abis/Iub

STM-1 2 (optional) SFP (LC) ITU G.957ITU G.707

E1/T1 16 (8pairs optional) DB44 ITU G.703/G.704

Ethernet

1 (10M/100M/1000Melectrical)

Auto-Negotiation

Auto-MDI/MDIX

RJ4510/100/1000BASE-T IEEE802.3 compatible

1 (1000M optical) or

1 (100M optical)SFP (LC)

1000BASE-LX IEEE 802.3compatible

100BASE-FX IEEE 802.3compatible

Clock GPS 1 SMA

GPS Antenna Interface

NMEA 0183 V3.0

BasebandMonitor &Alarm

DryContacts

6 (Input),

2 (Input / Output)DB44 -

RS485 1 DB44 -

RF Monitor &Alarm

DryContacts

4 per RRU DB15 -

RS485 1 per RRU DB15 -



30/41


5 Technical Indices

Table 14 ZXSDR BS8700 Technical Indices

Type Item Indices

Performance

Indices

WorkingFrequency

R8840 2100 MHz/AWS

R8860/R8860E 850/900/1800/1900 MHz

R8880 2100 MHz

R8890 2100 MHz

Capacity

Max Carrier/Sector 30 CS (UMTS single mode)

Max Carrier/TRX 60 TRX (GSM single mode)

Max Channel Element forUMTS

UL: 960/1920 CEDL: 960/1920 CE

Max Channels

Per Cell for UMTS123

Max ThroughputUL: 86.5 Mbps

DL: 324 Mbps

OutputPower

RRU Type Output Power (TOC)

R8840 60W

R8860/R8860E 80W

R8880 2*60W

R8890 3*60W

ReceivingSensitivity

-113dBm@GSM Single Antenna

-126.5dBm@UMTS single antenna

-129.2dBm@UMTS double antennas

Power

Indices

Powersupply,voltagerange ofvariation

B8200 -48V DC (-57VDC ~ -40VDC)

R8840 -48V DC (-60VDC ~ -35VDC)

220 V AC (90VAC ~ 300VAC)

110 V AC (85VAC ~ 135VAC)

R8860/R8860E -48V DC (-57VDC ~ -37VDC)

R8880/R8890 -48VDC (-60 V DC~ - 37VDC)

220VAC (165VAC~ 300VAC)

110VAC (85VAC ~ 135VAC)

PowerConsumption

Indices

UMTS singlemode

Type Typical Power Consumption (W)

B8200 6CS/1 BPC 80

B8200 12CS/2 BPC 115

B8200 18CS/3 BPC 150

B8200 24CS/4 BPC 185

R8840 1C/TOC 20W 100

R8840 2C/TOC 40W 125

R8840 3C/TOC 60W 160



31/41


R8880 S1/TOC 20W 100

R8880 S2/TOC 40W 135

R8880 S3/TOC 60W 165

R8890 S111/TOC 3*20W 210R8890 S222/TOC 3*40W 315

R8890 S333/TOC 3*60W 405

GSM SingleMode

R8860/R8860E S1/TOC 20W 185

R8860/R8860E S2/TOC 40W 195

R8860/R8860E S4/TOC 80W 215

G/U Dual-Mode

R8860/R8860E 4G1U/TOC4*15W (GSM)+20W (UMTS)

215

Environment

Indices

Temperature BBU:

-20C+55C

RRU:

R8840/R8860/R8860E/R8880: -40C+55C

R8890: -40C+50C

RelativeHumidity

BBU:

5%95%

RRU:

R8840/R8860/R8860E: 5% ~ 100%

R8880/R8890: 10% ~ 100%

Waterproof

/Dustproof

BBU: IP20

RRU: IP65

Ground 5

EMC IndicesNational/InternationalStandard

YD/T 1595.2-2007

ETSI EN 301 489-01, ETSI EN 301 489-23ETSI EN 300 386V1.3.2

(CISPR22) Class B

Directive 1999/5/EC (R&TTE)

ReliabilityIndices

MTBF

BBU: 233,000 hours

R8840: 420,000 hours

R8860/R8860E: 380,000 hours

R8880: 322,000 hours

R8890: 280,000 hours

MTTRBBU: 0.5 hours

RRU: 1 hours

Availability BBU: 99.999785%

R8840: 99.999762%

R8860/R8860E: 99.999868%

R8880: 99.999689%

R8890: 99.999643%

DownDuration

BBU: 1.128 min/year

R8840: 1.251 min/year

R8860/R8860E: 1.383 min/year

R8880: 1.632 min/year

R8890: 1.877 min/year



32/41


6 Operation and Maintenance

The operation and management of BS8700 is performed by the ZTE unified networkmanagement system, NetNumen M31, which adopts client/server architecture. Theserver runs Solaris OS + Oracle database. The client adopts Windows system, enablinghuman-machine management for the network element.

Figure 25 NetNumen M31 Elements Management System

The BSS/UTRAN/E-UTRAN provides a transparent channel to implement operation andmaintenance information interaction between NetNumen M31 and the radio network.Management of the BSC/RNC and the BTS/Node B/eNode B adopts unified client

interface for security management and operation log. NetNumen M31 also supportsCORBA/SNMP Itf-N interface towards third-part NMS.

BS8700 operation and maintenance system supports the following functions:

Version Management

With this function, administrator can view versions of the all software and hardwarerunning at the foreground. The hardware version includes the BOOT version numberand its generation time. The software version includes the software version number,download time and its current running state.


NMS/OSS

Alarm Conf.

Perf

ormance

Version

Topology Security

NetNumen M31

Adaptation Layer

GSMBSS

UMTSUTRAN

LTEE-UTRAN

NOP

Toolset

NetworkManagementLayer

ElementManagementLayer

NetworkElement

Itf-N Interface

BIN / MML/ Fileinterface


33/41


The background provides a software downloading system for softwaredownload/upgrade at the foreground. Before download/upgrade, warehousingprocessing is required. The warehousing process will copy the version files to the serverand register to the server.

Software versions existing in the base stations can be activated with or without softwaretests.

Alarm Management

The alarm management system monitors running states of the base stations,dynamically displays the rack structure of the foreground module and collects abnormalinformation of the boards, links, database and server in real time. These functions makeit convenient to analyze, address the problems, maintenance and repair.

Information collected by the alarm management system includes notification, alarm andalarm recovery.

The alarm management system synchronizes alarms, reports historical alarms andcurrent alarms, and sets and queries alarm shielding.

Configuration Management

Configuration management implements functions of equipment configuration and radioconfiguration.

Log Management

NetNumen M31 system provides the log management function. Any operation performed

by operator will be recorded automatically. Thus, the operation maintenanceadministrator can query historical operation records. Log records are saved in the NMdatabase server.

In the BS8700, it has memory on CC board in order to preserve database, the storagetime is 90 days.

Security Management

Security management is implemented through user management and user groupmanagement. The user management includes the management for user name,password and user groups which the user belongs to. The user group management

includes the management of user group name and authority information (indicatingauthorities the user group has).

Performance Management

Performance management is to measure, report!and provide performances statistic ofbase stations.

Diagnosis and Test

Diagnosis and test are important components of EMS. The network administrator cancheck whether system hardware is working properly by diagnosis and test. They are also

able to trace and fix the faults on time to secure the safe operation of the system.



34/41


Base station diagnosis and test cover the following functions:

Information reporting

Board link testing

Receiving field strength testing

Environment information monitoring

Other Supplementary Functions

The operation and maintenance system also provides other supplementary functions tofacilitate base station maintenance, which include but not limited signaling tracing,channel viewing, abnormal record reporting and viewing.

In ZXSDR BS8700, the time of impact on service because of the hardwares broken-down is under control. ZXSDR BS8700 has auto restart mechanism which supportsRadio Unit auto restart, main control board auto restart, Baseband processing unit autorestart, the whole base station auto restart.

The Radio Unit auto restart time is one minute. The main control board which is CCboard auto restart time is 3 minutes. The Baseband processing unit that includes UBPGand BPC board auto restart time is one minute. The whole base station auto restart timeis 4 minutes.



35/41


7 Configuration Principles

7.1 Baseband Unit Configuration Principles

Different baseband processing boards can be configured in BS8700 baseband unit fordifferent scenario. UBPG board supports GSM/GPRS/EDGE/E-EDGE. BPC boardsupports UMTS/HSPA/HSPA+. The processing capability of baseband processingboards is listed as below:

Single UBPG board supports GSM/GPRS/EDGE/E-EDGE 12TRX;

Single BPC supports 6CS, uplink 192/384CE and downlink 192/384CE;

In typical configuration, the BS8700 baseband unit provides 4 baseband processingboard slots. 1 more BP board can be available if only one optical switch board isconfigured.

FS: Fabric Switch board, there are 6 pairs CPRI interface in each FS board, 2 FS boardscan be configured in B8200 maximally.

SA: Site Alarm board, support!8 dry contacts and 8 pairs of E1/T1, 1 SA board for eachB8200 is mandatory configuration.

SE: Site Alarm Extension board, support!8 dry contacts and 8 pairs of E1/T1, 1 SE boardcan be configured if the requirements of dry contacts or E1/T1 exceed the SA capacity.

NIS: Network Interface of STM-1 board, configured when Abis/Iub adopts STM-1interface.

PM: Power Module, 1 PM board for default configuration, if needed, 1+1 is availableoption.

FAM: Fan array Module, 1 FAM board for each B8200 is mandatory configuration.

CC: Control and Clock board, 1 CC board for default configuration, if needed, 1+1backup or load sharing is an available option. One Control and Clock board supports 01FE/GE electrical interfaces and 01 FE/GE optical interfaces toward BSC (Abis) and

RNC(Iub).

7.2 Radio Unit Configuration Principles

On different frequencies and software configurations, BS8700 can be configured asvarious GSM/UMTS base stations:

In GSM single mode, R8860/R8860E can support!1 to 6 TRX.

In UMTS single mode, R8840 and R8860/R8860E can support!1 to 4 carriers, R8880 can

support!1 to 4 carriers in both 2 sectors, R8890 can support!1 to 3 carriers in 3 sectors;



36/41


If GSM/UMTS are in the dual mode, single R8860/R8860E can support!1 UMTS Carriers + 4

GSM TRX or 2 UMTS Carriers + 2 GSM TRX at maximum;

7.3 GSM Single Mode Configuration Principles

R8860/R8860E is needed to be configured for GSM single mode, which is based onmulti-carrier technology. In GSM mode, R8860/R8860E supports 1 to 6 TRX in 1 sector.For baseband part, one UBPG board supports 12 TRX.

7.3.1 R8860/R8860E configuration

Table 15 ZXSDR BS8700 Configuration for GSM Single Mode (Multi-carrier)

Site Type R8860/R8860EQty

B8200 Qty UBPG Qty

S4/4/4 3 1 1

S8/8/8 6 1 2

S12/12/12

9 1 3

7.4 UMTS Single Mode Configuration Principles

R8840, R8860/R8860E, R8880 or R8890 is needed to be configured for UMTS single

mode.

R8840s maximum output power is 60W, supporting 3 carriers when it ensures the 20Woutput power for each carrier.

R8860/R8860Es maximum output power is 80W, supporting 4 carriers when it ensuresthe 20W output power for each carrier.

R8880s maximum output power is 2*60W, supporting 3 carriers when it ensures the20W output power for each carrier.

R8890 maximum output power is 3*60W working on 2100MHz, supporting 3 carriers 3sectors when it ensures the 20W output power for each carrier.

For baseband part, one BPC board supports 6CS.

7.4.1 R8840/R8880 configuration

Table 16 ZXSDR BS8700 Configuration UMTS Single Mode (R8840/R8880)

Site Type R8840/R8880 Qty B8200 Qty BPC Qty

S1/1/1 3 1 1

S2/2/2 3 1 1



37/41


S3/3/3 3 1 2

S2/2/2/2/2/2 6 1 2

7.4.2 R8860/R8860E configuration

Table 17 ZXSDR BS8700 Configuration UMTS Single Mode (R8860/R8860E)

Site Type R8860/R8860E Qty B8200 Qty BPC Qty

S1/1/1 3 1 1

S2/2/2 3 1 1

S4/4/4 3 1 2

S2/2/2/2/2/2 6 1 2

7.4.3 R8890 configuration

Table 18 ZXSDR BS8700 Configuration UMTS Single Mode

Site Type R8890 Qty B8200 Qty BPC Qty

S1/1/1 1 1 1

S2/2/2 1 1 1

S3/3/3 1 1 2

S2/2/2/2/2/2 2 1 2

7.5 GSM/UMTS Dual Mode Configuration Principles

7.5.1 GSM 850M/900M/1800M/1900M and UMTS 850M/900M/1800M/1900MDual-Mode Network in Same Spectrum

R8860/R8860E can be configured in 850/900/1800/1900M G/U dual-mode. OneR8860/R8860E supports 4 GSM TRX + 1 UMTS carrier or 2 GSM TRX + 2 UMTS

carriers simultaneously.

Table 19 BS8700 Configuration for G/U Dual-Mode (Same Spectrum)

Site Type R8860/R8860E Qty

B8200 Qty UBPG Qty BPC Qty

G:S444+U:S111 3 1 1 1

G: S222+U:S222 3 1 1 1

G: S666+U:S333 6 1 2 2



38/41


7.5.2 GSM 850M/900M/1800M/1900M and UMTS 2100M Dual-Mode Networkin Different Spectrums

R8840 or R8880 and R8860/R8860E are configured simultaneously in this scenario,

R8840 or R8880 is used for UMTS 2100M while R8860/R8860E is used for GSM850/900/1800/1900M.

Wideband combiner is required in the mode of co-feeder-line and co-antenna.

Table 20 BS8700 Configuration for G/U Dual-Mode (Different Spectrums)

Site Type R8840/R8880 Qty

R8860/R8860E Qty

B8200Qty

UBPGQty

BPCQty

U:S222(2100M) +

G:S6/6/6(850/900/1800/1900M)

3 3 1 2 1



39/41


8 Acronyms and AbbreviationAbbreviations Full Characteristics

3GPP 3rd Generation Partnership Project

64QAM 64 grade Quadrature Amplitude Modulation

AGPS Assisted GPS

AMR Adaptive Multi Rate

BB Base Band

BBS Base Band Sub-system

BBU Base Band processing Unit

BCCH Broadcast Control Channel

BITS Building Integrated Timing Supply

BP Base band Processing

BPC Base band Processing Board Type C for UMTS

BRACS Bearer Access Control Sub-system

BRS Bearer Sub-system

BSC Base Station Controller

BSP Board Support!Package

BTS Base Transceiver Station

CAPEX Capital Expenditure

CC Control & Clock

CE Channel Element

CN Core Network

CORBA Common Object Request Broker Architecture

CPRI Common Public Radio Interface

CS Carrier Sector

DBS Data Base Sub-system

DL Down Link

DTX Discontinuous transmission

EDGE Enhanced Data rates for GSM Evolution

E-EDGE Enhanced EDGE

EFR Enhanced Full Rate



40/41


Abbreviations Full Characteristics

FAM Fan Module

FE Fast Ethernet

FP Frame Protocol

FR Full Rate

FS Fabric Switch

GE Gigabit Ethernet

GERAN GSM Edge Radio Access Network

GPS Global Positioning System

GSM Global System for Mobile communications

HR Half Rate

HSPA+ HSPA Evolution

LMT Local Maintenance Terminal

LTE Long Term Evolution

MicroTCA Micro Telecommunications Computing Architecture

MIMO Multi Input Multi Output

MS/UE Mobile Station/User Equipment

MTBF Mean Time Between Failures

MTTR Mean Time To Recovery

NBAP Node B Application Part

NIS Network Interface of STM-1

NM NetNumen, Name of ZTE OMCR

NMS Network Management System

NOP Network Optimization & Planning

OAM Operating And Maintenance

OPEX Operation Expenditure

OSS Operation Support!Sub-system

PM Power Module

PS Packet Switch

PtM Point to Multi-point

PtP Point to Point

RCS Radio Control Sub-system

RF Radio Frequency



41/41


Abbreviations Full Characteristics

RNC Radio Network Controller

RRU Remote Radio Unit

RTT Round Trip Time

SA Site Alarm

SCS System Control Sub-system

SDH Synchronous Digital Hierarchy

SDR Software Defined Radio

SE Site Alarm Extension

SNMP Simple Network Management Protocol

TA Time Advance

TNS Transport!Network Sub-system

UBPG Universal Base band Processing for GSM

UL Up Link

UTRAN UMTS Terrestrial Radio Access Network

WCDMA Wideband Code Division Multiple Access

Documents

2 1 3 ZXSDR BS8700 Product Description