Upload
vuongkhuong
View
248
Download
2
Embed Size (px)
Citation preview
I
1967-1968
Mustang
Installation Manual
Revised September 11, 2013 Page II
Table of Contents TABLE OF CONTENTS ....................................................................................................................................................................... II
WELCOME TO THE TEAM OF CLASSIC INSTRUMENTS!...................................................................................................... III
REMOVE ORIGINAL INSTRUMENT PANEL .................................................................................................................................. 1
DETERMINE SPEEDOMETER SIGNAL ........................................................................................................................................... 3
WIRING THE SPEEDOMETER ........................................................................................................................................................... 4
DETERMINE TACHOMETER SIGNAL ............................................................................................................................................ 6 WIRING THE TACHOMETER ............................................................................................................................................................ 7
WIRING THE TEMPERATURE GAUGE ........................................................................................................................................... 8
WIRING THE OIL PRESSURE GAUGE ............................................................................................................................................ 9
WIRING THE FUEL LEVEL GAUGE .............................................................................................................................................. 10
WIRING THE TURN SIGNALS ......................................................................................................................................................... 10
WIRING THE HIGH BEAM INDICATOR ....................................................................................................................................... 10 WIRING THE BRAKE LIGHT INDICATOR ................................................................................................................................... 10
WIRING THE DASH LIGHTS ............................................................................................................................................................ 10
INSTRUMENT PANEL WIRE HARNESS ........................................................................................................................................ 11
CALIBRATING THE SPEEDOMETER ............................................................................................................................................ 12 SN16F PULSE SIGNAL GENERATOR SIGNAL ........................................................................................................................................ 12 SN74 SPEEDOMETER SIGNAL INTERFACE SIGNAL ............................................................................................................................... 13
16-PULSE SPEEDOMETER 16,000 PPM CALIBRATION CHART ............................................................................................. 15
MOUNT NEW INSTRUMENT PANEL ............................................................................................................................................. 16
Revised September 11, 2013 Page III
Welcome to the Team of Classic Instruments!
Our congratulations and appreciation for your purchase of one of the finest quality set of specialty instruments ever produced! Your instrument set has been conceived, designed, and manufactured by Classic Instruments, Inc. in the U.S.A. Each instrument has been tested and certified for accuracy and quality before packaging and shipping.
For trouble-free installation and operation, follow the instructions exactly as outlined. Your instruments
were assembled to precise specifications and although each has a five (5) year warranty covering defective parts and workmanship – this warranty will not cover instruments or sending units which have been installed incorrectly.
Follow our recommended procedures for installation and proper hookup to maintain the value and
appearance of your instrument set during many future years of accurate and dependable service!
CAUTION! - When Wiring Your Instruments Always Disconnect Your Battery First!
Follow our instructions to guarantee trouble-free installation and correct operation. Our installation instructions and procedures should take priority over instructions furnished by any other manufactures of ignition systems, wiring harnesses, gauges, etc.
TECHNICAL ASSISTANCE
1-800-575-0461 OR
Visit our new website for the latest in gauge design and updates to our installation manual at:
www.classicinstruments.com
Revised September 11, 2013 Page 1
Remove Original Instrument Panel
1) Disconnect the battery before beginning the replacement of the new instrument panel.
2) Remove the 5 screws holding the instrument panel to the dash. Three screws are located at the top of the instrument panel and two screws are located at the bottom of the instrument panel. Save these screws to use when installing the new instrument panel.
3) Remove the nut from the stud located on the passenger side of the instrument panel. Save this
nut to use when installing the new instrument panel.
4) Unscrew the speedometer cable from the back of the speedometer.
5) Unplug the wiper switch from the vehicle wire harness.
6) Unplug the two existing instrument panel wire harness connectors from the vehicle wire harness.
7) Remove the original instrument panel from the dash.
8) Remove the two screws attaching the wiper switch to the original instrument panel and then remove the wiper switch. Save the screws and wiper switch to use with the new instrument panel.
See Figure A and Figure B on the following page
Revised September 11, 2013 Page 2
Figure A: Example of original instrument cluster removed from dash (5 screws and 1 nut removed)
Figure B: Unplugged wiper switch and original instrument harness
Unplug
Screws
Nut
Remove
Revised September 11, 2013 Page 3
Determine Speedometer Signal
Determine where you are going to get the speed signal for your speedometer. If your transmission has a port where a mechanical speedometer cable was attached, you will need a pulse signal generator. The Ford style pulse signal generator is shown below in figure 1. The pulse signal generator produces 16 pulses per revolution and has three connection wires. When using a pulse signal generator, you will need to calibrate the speedometer according to the 16,000 pulse per mile (ppm) chart on page 15 of this manual. You will need to retain the gear and holder from the transmission end of the speedometer cable to use on the pulse signal generator. If your transmission has an electronic vehicle speed sensor (VSS) or computer (ECM / PCM), you will need a speedometer signal interface, shown below in figure 2.
RedBlackWhite
Red: +12VDC Black: Ground White: Signal
Figure 1: Ford style pulse signal generator [SN16F]
Classic Instruments Inc.
NO 321
www.classicinstruments.com
1 2
OU
TP
UT
INP
UT
SE
NS
OR
GN
D
GR
OU
ND
PO
WE
R
PU
SH
BU
TT
ON
PU
SH
BU
TT
ON
SE
NS
OR
PW
R
CR
UIS
E
4
SN74SPEEDOMETER
SIGNALINTERFACE
SW#1 Input Type LED#2 Sensitivity #1 ADJ#3 Output Type #2 AUTO#4 not used 1 & 2 reset
Figure 2: Speedometer signal interface [SN74]
Revised September 11, 2013 Page 4
Wiring the Speedometer
1) Connect +12VDC from the accessory side of the ignition switch to the Pink/White wire on the speedometer connector (position F) of the instrument wire harness. If accessory of ignition is not available, connect to a switched and dedicated fuse on the fuse panel. This will help prevent interference to the speedometer from the power source.
2) Connect the red wire from the pulse signal generator OR “Power” from the SN74 to the
Purple/White wire on the speedometer connector (position C) of the instrument wire harness.
3) Connect a dedicated chassis ground (i.e. don’t stack with any other ground wires) to the black/white wire on the speedometer connector (position E) of the instrument wire harness. This will help prevent interference to the speedometer from the ground.
4) Connect the black wire from the pulse signal generator OR “Ground” from the SN74 to the yellow
wire on the speedometer connector (position A) of the instrument wire harness.
5) Connect the white wire from the pulse signal generator OR “Output” from the SN74 to the purple wire on the speedometer connector (position B) of the instrument wire harness.
6) If using the SN74 speedometer signal interface:
A. Connect one wire of the transmission VSS to the SN74 “Sensor GND” and the other wire of
the transmission VSS to the SN74 “Input”.
OR
B. Connect the speed signal wire from the ECM / PCM to the SN74 “Input”.
Revised September 11, 2013 Page 5
Classic Instruments Inc.
NO 321
www.classicinstruments.com
1 2
OU
TPU
TIN
PU
TS
EN
SO
R G
ND
GR
OU
ND
PO
WE
R
PU
SH
BU
TTO
NP
US
HB
UTT
ON
SE
NS
OR
PW
R
CR
UIS
E
4
SN74SPEEDOMETER
SIGNALINTERFACE
SW#1 Input Type LED#2 Sensitivity #1 ADJ#3 Output Type #2 AUTO#4 not used 1 & 2 reset
1, 2 ON3, 4 OFF
To Purple/White harness wire
To Yellow harness wire
From ECM/PCM speed signal
To Purple harness wire
To pushbutton
To pushbutton
ECM/PCM Speed Signal Wiring
Classic Instruments Inc.
NO 321
www.classicinstruments.com
1 2
OU
TPU
TIN
PU
TS
EN
SO
R G
ND
GR
OU
ND
PO
WE
R
PU
SH
BU
TTO
NP
US
HB
UTT
ON
SE
NS
OR
PW
R
CR
UIS
E
4
SN74SPEEDOMETER
SIGNALINTERFACE
SW#1 Input Type LED#2 Sensitivity #1 ADJ#3 Output Type #2 AUTO#4 not used 1 & 2 reset
1, 2, 3, 4 OFFTo Purple/White harness wire
To Yellow harness wire
To Purple harness wire
To pushbutton
To pushbutton
From VSS low signal
From VSS high signal
Electronic VSS Speed Signal Wiring
To purple/white harness wire
To yellow harness wire
To purple harness wire
Red
Black
White
Pulse Signal Generator Wiring
Revised September 11, 2013 Page 6
Determine Tachometer Signal
STANDARD POINTS & CONDENSER SYSTEM Signal comes from the negative side of the coil (usually marked as “-“). GMC – HEI (High Energy Ignition System) Signal comes from the “TACH” terminal on coil side of distributor cap. MSD (Multiple Spark Discharge System) Signal comes from the TACH post on the MSD box. If there isn’t a MSD box, the signal comes from the negative side of the coil. If the tachometer does not respond correctly, your MSD system may require a MSD TACH adapter. Part No. 8910 or 8920. Contact MSD to find out which adapter you should use for your application. VERTEX MAGNETO SYSTEM Signal comes from the “KILL” terminal on side the of Vertex magneto body. An external adapter such as an MSD Pro Mag Tach Converter #8132 may be required. ACCEL IGNITION COILS Signal comes from the negative side of the coil. CAUTION! Some Accel ignition coils require the tach signal wire to be connected to the “+” terminal on the coil! PLEASE carefully read Accel’s instructions before connecting ignition coil. MALLORY IGNITION Signal comes from the negative terminal side of coil (usually marked as “-“). IMPORTANT! Some Mallory ignition systems may require you to adjust the tachometer selector switch to be set at the 4-cylinder setting (rather than the 8-cylinder setting). The selector switch is located on the backside of the tachometer case. ECM TACHOMETER SIGNAL Signal comes from the computer. When using this type of signal, you may need to set the tachometer to a 4-cylinder setting regardless of the actual cylinders on the engine. Signals below 8V amplitude require the use of either the SN76 tach adapter or a 1K .25W pull-up resistor installed between the signal and power post of the tachometer. See Table 2 for settings. MULTIPLE COIL IGNITION SYSTEMS A tach adapter is required for these ignition systems. A tach signal driver such as the MSD #8913, which produces a 12V square wave signal, is recommended. Please check with manufacturer for your specific application. NOTICE: For all other ignition systems please look at the owner’s manual for that system.
Revised September 11, 2013 Page 7
Wiring the Tachometer
1) Connect switched +12VDC power to the pink wire on the power/lighting connector (position H) of the instrument wire harness.
2) Connect a good chassis ground to the black wire on the power/lighting connector (position J) of the
instrument wire harness.
3) Connect the tachometer signal to the white wire on the signal connector (position J) of the instrument wire harness.
4) Set the tachometer dip switches to the appropriate cylinder setting for your signal. Refer to Table 2
and Figure 3 below.
Note: Some ECM tachometer signals require the tachometer to be set at the 4-cylinder setting regardless of the actual cylinders on the engine.
Number of Cylinders Tachometer Dip Switch Setting
4 1 & 2 OPEN 6 2 & 3 OPEN 8 2 OPEN
Table 2: Tachometer Setup
(Set dip-switches from Table to OPEN, all others CLOSED)
1 2 3 4 5 6 7 8
--------------- OPEN ---------------
Figure 3: Dip switches on back of tachometer (Figure shows the factory preset 8 cylinder setting)
Revised September 11, 2013 Page 8
Wiring the Temperature Gauge
1) Install the Classic Instruments temperature sender in the intake manifold of the engine. The threads of the sender are tapered and should not require additional sealant. Do not use Teflon tape on the threads of the sender. If necessary, a small amount liquid Teflon pipe sealer may be used. A good ground is essential between the temperature sender and the engine block for proper gauge operation. Use of Teflon tape on the sender threads may degrade the ground contact between the sender and the engine.
2) Connect the temperature sender to the dark green wire on the signal connector (position A) of the
instrument wire harness. See Figure 4 below.
3) The temperature gauge uses the same power and ground used for the tachometer. If you have already connected them, no other connections are necessary. Otherwise, see step 1 & 2 of wiring the tachometer section.
Intake Manifold
Ring Terminal
Nylon Washer
Brass Washer
Nut
Lock Washer
Signal Wire
Figure 4: Connecting the temperature sender
Revised September 11, 2013 Page 9
Wiring the Oil Pressure Gauge
1) Install the Classic Instruments oil pressure sender in the engine block. Ford engine installations require the use of the 3-piece brass bushing kit which includes a thread adapter, 45 degree elbow and 1 inch extension. The threads of the sender and bushing kit are tapered and should not require additional sealant. Do not use Teflon tape on the threads of any part of the sender. If necessary, a small amount liquid Teflon pipe sealer may be used. A good ground is essential between the oil pressure sender and the engine block for proper gauge operation. Use of sealants on the sender threads may degrade the ground contact between the sender and the engine.
2) Connect the oil pressure sender to the dark blue wire on the signal connector (position B) of the
instrument wire harness. See Figure 5 below.
3) The oil pressure gauge uses the same power and ground used for the tachometer. If you have already connected them, no other connections are necessary. Otherwise, see step 1 & 2 of wiring the tachometer section.
Thread Adapter
Entension
45° Elbow
Ring Terminal
Oil Pressure Sender
Signal Wire
Washer
Lock Washer
Nut
Figure 5: Connecting the oil pressure sender
Revised September 11, 2013 Page 10
Wiring the Fuel Level Gauge
1) The fuel level gauge in your instrument cluster is designed to work with the stock sending unit in your 1967 – 1968 Mustang. The stock fuel level sender generates an ohm range of 78 ohms at empty and 10 ohms at full. Connect the stock fuel level sender to the tan wire on the signal connector (position D) of the instrument wire harness.
2) The fuel level gauge uses the same power and ground used for the tachometer. If you have already
connected them, no other connections are necessary. Otherwise, see step 1 & 2 of wiring the tachometer section.
Wiring the Turn Signals
1) Connect the vehicle’s right turn signal wire to the blue wire on the signal connector (position G) of the instrument wire harness.
2) Connect the vehicle’s left turn signal wire to the light blue wire on the signal connector (position F)
of the instrument wire harness.
Wiring the High Beam Indicator
1) Connect the vehicle’s high beam indicator signal wire to the light green wire on the signal connector (position E) of the instrument wire harness.
Wiring the Brake Light Indicator
1) Connect the brown wire on the signal connector (position H) of the instrument wire harness to the emergency brake signal wire or switch.
Wiring the Dash Lights
1) Connect the vehicle’s dash light power wire to the grey wire on the power / lighting connector (position K) of the instrument wire harness.
Revised September 11, 2013 Page 11
Instrument Panel Wire Harness
LSI
LSI
Dash Light Pow
er [Grey - K
]G
ood Chassis G
round [Black - J]+12VD
C sw
itched [Pink - H
]
Speed Sensor G
round [Yellow
- A]
Speed S
ignal [Purple - B
]S
peed Sensor Power [P
urple / White - C
]S
pare [D]
Dedicated C
hassis Ground [B
lack / White - E
]+12VD
C Sw
itched / Dedicated [P
ink / White - F
]
Not U
sed [Dk. G
reen - A]
Oil P
ressure Signal [Dk. B
lue - B]
Not U
sed [C]
Fuel Level Signal [Tan - D]
High Beam
Indicator [Lt. Green - E
]Left Turn Indicator [Lt. B
lue - F]
Right Turn Indicator [B
lue - G]
Brake Indicator [B
rown - H
]Tachom
eter Signal [White - J]
Yellow
Black / White
Pink / White
Purple / White
Purple
Grey
Grey
Grey
Grey
Black
Black
Black
Pink
Pink
Pink
Dk. Blue
Blue
Brown
Lt. Green
White
Lt. Blue
Dk. Green
LSI
Grey
Black
Pink
Tan
Pink
1211
109
87
65
43
21
OPEN
87
65
43
21
OPEN
Revised September 11, 2013 Page 12
Calibrating the Speedometer SN16F Pulse Signal Generator Signal
IMPORTANT: Calibrate your speedometer before completely mounting your instrument panel. (You will need to adjust dip switches on the back of the speedometer to complete the calibration) Be sure the 12 dip switches on the back of the gauge are set to the default setting (5, 6, 7, 8 OPEN) before performing the calibration road test.
1) To check your speedometer reading, follow and pace another car (with an accurate speedometer) to a speed of 60 MPH true road speed. A GPS navigation system can also be utilized for this purpose.
2) Determine the speed you are reading on your speedometer when the pace car is at 60 MPH or you
register 60 MPH on your GPS.
3) Refer to the 16-pulse speedometer 16,000 ppm calibration chart on page 15 for adjustments. Find the MPH you were reading while pacing a car with an accurate speedometer or GPS reading. Note the dip switch positions in the second column.
4) Turn the ignition off. Set the dip switches identified in the second column to OPEN (pushed in away
from the numbered side). All other switches should be CLOSED (pushed in toward the numbered side).
5) Your speedometer should now read the same as the pace car of GPS.
Revised September 11, 2013 Page 13
SN74 Speedometer Signal Interface Signal
Signal Source Switch Setting
SN16F pulse signal generator 1, 2 ON – 3, 4 OFF VSS 1, 2, 3, 4 OFF
ECM / PCM 1, 2 ON – 3, 4 OFF Switch 1 –- OFF = signal generator speed input, ON = ECM/PCM speed input Switch 2 –- OFF = high sensitivity, ON = low sensitivity Switch 3 –- OFF = 16,000ppm signal output, ON = 8,000ppm signal output Switch 4 –- Not Used
Entering Calibration Mode
1) Start with the vehicle power / engine off. Push and hold the pushbutton then start the engine. 2) When the engine is running, release the pushbutton. 3) The red LED labeled “1” on the module will be lit (indicating real-time calibration mode). 4) Tapping the pushbutton will cause the red LED labeled “2” on the module to turn on (indicating
marked mile calibration mode). 5) Tapping the pushbutton again will cause both red LEDS on the module to turn on (indicating reset
mode). 6) Tapping the pushbutton once again will cause the red LED labeled “1” to turn on again. Continuing
to tap the pushbutton will cycle LEDS on the module through the real-time, marked mile and reset modes.
7) Push and hold the pushbutton for approximately 5 seconds to “enter” the mode indicated by the red LED of the module.
Revised September 11, 2013 Page 14
Marked Mile Calibration Mode
1) Enter the calibration mode as detailed in the “Entering Calibration Mode” section of the instructions. 2) Push and hold the pushbutton with red LED “2” lit until LED “2” starts blinking (approximately 5
seconds) 3) Begin driving a known mile. (The green LED on the module should blink once you start moving,
indicating that it is getting a signal.) 4) When driving the mile, the speedometer will not indicate any speed. This is normal. 5) At the end of the mile, press and hold the pushbutton until the red LED “2” goes off (approximately
5 seconds)
Real-Time Calibration Mode
1) Enter the calibration mode as detailed in the “Entering Calibration Mode” section of the instructions. 2) Push and hold the pushbutton with red LED “1” lit until LED “1” starts blinking. (approximately 5
seconds) 3) Drive a known speed (use GPS or pace another car). 4) Press and hold the pushbutton to change the speed shown on the speedometer. The first time the
pushbutton is pressed and held, the speed shown on the speedometer will increase. The second time the pushbutton is pressed and held, the speed shown on the speedometer will decrease.
5) The pushbutton will alternate increasing or decreasing the speed shown on the speedometer each time it is pressed. Press and hold the pushbutton to fine tune the speed shown on the speedometer.
6) Once the correct speed on the speedometer has been achieved, wait 8 seconds without pushing the pushbutton in order to save the calibration.
7) The green LED below the red “1” and “2” LEDS indicates the module is getting power if on solid and indicates that the module is receiving a signal if blinking. (the green LED will not be on solid while selecting calibration modes, but will function when a calibration mode has been entered)
Module Reset
1) Enter the calibration mode as detailed in the “Entering Calibration Mode” section of the instructions. 2) Tap the pushbutton until the red LED “1” and “2” are both lit. 3) With both LED “1” & “2” lit, press and hold the pushbutton until both red LEDs turn off.
(approximately 5 seconds)
The module will now be reset to the factory settings.
Revised September 11, 2013 Page 15
16-Pulse Speedometer 16,000 PPM Calibration Chart
(Default Dip Switch Setting)
1 2 3 4 5 6 7 8 9 10 11 12
------------------------- OPEN -------------------------
(Switch 5 6 7 8 OPEN) Set speedometer switches 5 6 7 8 OPEN, all others closed (code for 16,000 PPM). Drive vehicle at 60mph. If the speedometer reads other than 60, set switches per chart below.
Speedometer Reading OPEN SWITCH Speedometer Reading OPEN SWITCH 40 MPH 8 9 11 12 80 MPH 4 5 6 10 12 41 MPH 7 10 12 81 MPH 4 5 6 8 42 MPH 7 8 82 MPH 4 5 6 8 9 11 12 43 MPH 7 8 9 11 12 83 MPH 4 5 6 7 10 44 MPH 6 10 84 MPH 4 5 6 7 8 45 MPH 6 8 85 MPH 4 5 6 7 8 9 11 12 46 MPH 6 8 9 11 12 86 MPH 3 10 12 47 MPH 6 7 10 12 87 MPH 3 8 48 MPH 6 7 8 88 MPH 3 8 9 11 12 49 MPH 6 7 8 9 11 12 89 MPH 3 7 10 12 50 MPH 5 10 90 MPH 3 7 8 51 MPH 5 8 91 MPH 3 7 8 9 11 12 52 MPH 5 8 9 11 12 92 MPH 3 6 11 12 53 MPH 5 7 10 12 93 MPH 3 6 8 54 MPH 5 7 8 94 MPH 3 6 8 9 11 12 55 MPH 5 7 8 9 11 12 95 MPH 3 6 7 10 12 56 MPH 5 6 10 12 96 MPH 3 6 7 8 57 MPH 5 6 8 97 MPH 3 6 7 8 9 11 12 58 MPH 5 6 8 9 11 12 98 MPH 3 5 10 12 59 MPH 5 6 7 10 12 99 MPH 3 5 8 60 MPH 5 6 7 8 100 MPH 3 5 8 9 11 12 61 MPH 5 6 7 8 9 11 12 101 MPH 3 5 7 10 12 62 MPH 4 10 12 102 MPH 3 5 7 8 63 MPH 4 8 103 MPH 3 5 7 8 9 11 12 64 MPH 4 8 9 11 12 104 MPH 3 5 6 10 12 65 MPH 4 7 10 105 MPH 3 5 6 8 66 MPH 4 7 8 106 MPH 3 5 6 8 9 11 12 67 MPH 4 7 8 9 11 12 107 MPH 3 5 6 7 10 12 68 MPH 4 6 10 12 108 MPH 3 5 6 7 8 69 MPH 4 6 8 109 MPH 3 5 6 7 8 9 11 12 70 MPH 4 6 8 9 11 12 110 MPH 3 4 10 12 71 MPH 4 6 7 10 12 111 MPH 3 4 8 72 MPH 4 6 7 8 112 MPH 3 4 8 9 11 12 73 MPH 4 6 7 8 9 11 12 113 MPH 3 4 7 10 12 74 MPH 4 5 10 12 114 MPH 3 4 7 8 75 MPH 4 5 8 115 MPH 3 4 7 8 9 11 12 76 MPH 4 5 8 9 11 12 116 MPH 3 4 6 10 12 77 MPH 4 5 7 10 12 117 MPH 3 4 6 8 78 MPH 4 5 7 8 118 MPH 3 4 6 8 9 11 12 79 MPH 4 5 7 8 9 11 12 119 MPH 3 4 6 7 10 12
Revised September 11, 2013 Page 16
Mount New Instrument Panel
1) Insert wiper switch into new instrument panel. Make sure the non-slotted mounting holes of the switch are toward the bottom of the new instrument panel. Use the original two screws saved from the original instrument panel to fasten the wiper switch to the new instrument panel.
2) Attach the original wiper switch plug to the back of the wiper switch.
3) Mount the new instrument panel to the dash using the 5 mounting screws and nut that were removed
from the original instrument panel. See mounting diagram below
Wiper Switch
Stud
6
5
4
32
OPEN
1 2 3 4 5 6 7 8 9 10 11 12
1
L
G
ISS I
G
LL
G
S I
6
1
4
5
87654321
OPEN
2 3