KDK Tools1-800-397-0952

1000 E. Butler Ave.Suite 102

Flagstaff, AZ 86001

KDK Tools1-800-397-0952

CONVERT DOWN TIME TO PRODUCTION TIME

With KDK pre-set QUICK CHANGE TOOLS, you convert costly

set-up time into profitable production time. Short run, repeat

jobs are no longer a set-up time problem. Tools are

changed quickly . . . accurately. The bars are easy to

place on the dove tail from the top. The adjusting

screws for centering tools eliminates

shims underneath the tool bits. All

tools are heat treated and black

oxided to prevent rusting.

2

TOOL LOCKS WITH ATOUCH OF THE FINGER

Series

Recom-mended

LatheSwing

(inches)

CenterHeight

(inches)

LockDown

Bolt Dia.(inches)

Max.ToolBit

(inches)

Approx.Weight(lbs.)

IndividualTool Post

Price

CompleteSet

Price*

0 8 to 12 .750 & Up7/16 ⅜ 2¾ $278 $618

100 12 to 16 1.000 & Up7/16 ½ 5 $300 $716

150 15 to 18 1.250 & Up ⅝ ⅝ 6¼ $337 $854

200 18 to 24 1.500 & Up ¾ ¾(opt. 1”)

10½ $428 $1054

*Set includes Tool Post + 5 bars. (Standard Set pictured on page 3)

NOTE: The dovetail dimensions are the same on 0, 100, 150, and 200 Tool Posts which allowsbars from these series to be interchangeable. However, if using larger series tool holder onsmaller tool post, you must have enough center height.

00 .500 & Up5/16 ¼ 2 $268 $601

TOOL POSTS

COMPLETE SET—KDK TOOL POST PLUS 5 TOOL HOLDER BARS

KDK tool posts usually require a riser plate between the tool post and lathe compound to bring

tool to lathe center height. A blank T-nut and riser plate, up to 1⅛" thick, will be furnished FREE if

you specify lathe center height. See dimension "A" on page 10. Special riser plates thicker than

1⅛" furnished at time and material cost.

NOTE: For a machined T-Nut there is an additional charge. To insure correct size, furnish T-Slot

dimensions (see drawing on page 10).

STANDARD SET

September 2008

KDK Tools1-800-397-0952

EXTENSION TURNINGBAR COMBINATION

KDK TOOL POST

MASTER BAR FORBORING BARS OR OTHERROUND SHANKED TOOLSRISER PLATE

(If requested)

TURNING AND FACINGBAR COMBINATION

PARTINGBAR COMBINATION

THREADING AND FACINGBAR COMBINATION

STANDARD SET

3

T-NUT(Blank)

KDK Tools1-800-397-0952

Bar #Bit Capacity

(inches) Price

02 ⅜ $70

102 ½ $79

152 ⅝ $92

202 ¾ $114

202-1* 1 $145

THREADING & FACING BARCOMBINATION

002 ¼ $63

BARS

Bar #Bit Capacity

(inches) Price

01 ⅜ $72

101 ½ $83

151 ⅝ $96

201 ¾ $123

201-1* 1 $151

TURNING & FACING BARCOMBINATION

001 ¼ $63

Bar #Bit Capacity

(inches) Price

03 ⅜ $73

103 ½ $86

153 ⅝ $96

203 ¾ $113

203-1* 1 $145

EXTENSION TURNING BARCOMBINATION

003 ¼ $63

4*Not included in price of complete set.Must be ordered separately.

KDK Tools1-800-397-0952

BARS

Bar # BladeBit Capacity

(inches) Price

04 P2 3/32 x ½ $89

104 P3 ⅛ x 11/16 $96

154 P5X ⅛ x 7/8 $127

204 P8X ⅛ x 1⅛ $150

PARTING BAR COMBINATION

004 P2 1/8 x ½ $95

Bar #Bar Capacity

(inches) Price

05 ¾" Hole $88

105 1" Hole $96

155 1¼" Hole $133

205 1½" Hole $159

205-1¾* 1¾" Hole $197

205-2* 2" Hole $228

MASTER BAR FOR BORINGBARS

005 3/8 " Hole $95

4-POSITION BARCOMBINATION

Bar #Bit Capacity

(inches) Price

06* ⅜ $87

106* ½ $100

156* ⅝ $111

206* ¾ $128

206-1* 1 $158

006* ¼ $70

5

Also used for turningand facing.

*Not included in price of complete set.Must be ordered separately.

KDK Tools1-800-397-0952

5-B BORING BAR HOLDER(¼ to ½" Boring Bar Capacity)

By turning plate with groove over to flatside you can go down to ¼" diameter

Fits on 0, 100, 150, and 200 series KDKTool Posts.

Price…$104

RIGHT ANGLE TURNING BAR

Minimum tool overhang

Permits larger turning diameter.

Greater rigidity

Able to hold form tools to plunge on face of work

Bar #Bit Capacity

(inches) Price

020 ⅜ $89

1020 ½ $103

1520 ⅝ $115

2020 ¾ $135

2020-1 1 $166

NOTE: A larger series bar may be used on a similarseries tool post, but not the smaller bar on a larger seriespost.

5C COLLET BAR NO. 119

For Lathes having 1" Center Height orMore.

For use on No. 0, 100, 150 and 200KDK Tool Posts

Makes boring easier, allows instantchange to threading, internal grooving,drilling! Quick change from center drillingto tapping. Accuracy as good as yourmachine. Eliminates need for bushings.Assures the simplicity of KDK PresetQuick Change Tools to all 5C collet jobs!

CUTTINGTOOL ANDCOLLET NOTINCLUDED

BARS

6

KDK Part #

119Includes Spanner Wrench

and Lock Ring

Price

$129

119– 1Lock Ring

$18

119-2Spanner Wrench

$19

LockRing

SpannerWrench

KDK Tools1-800-397-0952

SWIVEL BAR FOR VARIED ANGLES

Bar #Bit Capacity

(inches) Price

118 ½ $117

1518 ⅝ $135

218 ¾ $154

7

BARS

DIAMOND KNURLS

FINE MED. COARSE

107

(40pi) (25pi) (16pi)

GKR-240GKL-240

GKR-225GKL-225

GKR-216GKL-216

(33pi) (21pi) (14pi)

KPR-233KPL-233

KPR-221KPL-221

KPR-214KPL-214

NOTE: Knurl Heads come standard withone pair each of Fine, Medium and CoarseDiamond Pattern Knurls. Straight Knurlsavailable upon request.

207

KNURLING BAR

KnurlingBar

with Headand 3 Pr.Knurls

Knurling Barwithout Head

RecommendedLathe Swing

(inches)

107-1 107 8 TO 16

$224 $115

207-1 207

$268 $145

15 TO 24

KNURLING HEAD AND KNURLS

Knurling Headfor Knurling Bar

and KnurlsKnurling Headwithout knurls Knurls (pair)

Knurl Size(inches)

1073K0-3 3K-0 107 KNURL (pair) 5/8 DIA x 5/16

$126 $58 $29

3K1-3 3K-1 207 KNURL (pair) 3/4 DIA x 3/8

$143 $65 $32207

KDK Tools1-800-397-0952

BARS

TOOL HOLDERS FOR TOP NOTCH®*THREADING AND GROOVING INSERTS

Rugged bridge clamp fits into a notch molded into the insert; thisallows precision threading. Features also include full formthreading, 60° vee, a complete series of grooving inserts, acmeand buttress.

Bar # Price Gage InsertClampScrew Price Clamp Price

KDK-NG-3 $170 NG-3 For ref. only,not available through

KDK

$2.50 CM-72 $13

KDK-NG-3 L.H.¹ $194

KDK-NG-4 $214 NG-4 For ref. only,not available through

KDKKDK-NG-4 L.H.¹ $237

Holders are designed to locate insert inclined 3° to provide back clearance down open side.*TOP NOTCH and KENDEX are registered Trademarks of Kennametal Inc. ¹Left Hand

60° Vee (NT, NTC, NTF, NF) These Inserts are designedfor cutting American Standard Unified 60° Vee Threads.They are furnished with a flat, radius, or a full form.

Grooving (NG, NO, NV, NR, NU) A completeline of Top Notch®* Grooving Inserts are avail-able for external and internal work. All NG In-serts are furnished with chamfered corners. Thesame holders and bars can be used for boththreading and grooving.

API Inserts (NDC, NDE, ND) For threading casings, tubing,line pipe and rotary joints. Full form 8 and 10 Rd, V038-40-50 Series.

Acme-Buttress (NA, NAS, NTB-A, NTB-B) 29°

S-412

CM-73¹

CM-72

CM-73¹

$13

$13

$13

S-412

S-412

S-412

$2.50

$2.50

$2.50

8

CARBIDE CUT-OFF TOOL HOLDER SYSTEM

KDKPart #

KDK ToolBodies

Tool Will FitFits BladesNumbers

Blade Size

DimensionFrom BottomOf Holder ToTop Of Insert Price(Inch) Metric

010 0,100,150 19-2 ¾ 19 MM 0.835 $120

1010 100, 150 26-2 THRU 26-6 11/32 26 MM 1.040 $133

1510 150, 200 32-2 THRU 32-6 1¼ 32 MM 1.312 $143

Carbide Cut-Off Tool Holder System will hold the “self grip” typecut-off blades (i.e.: Newcomer, Iscar, Carboloy, Kennametal, etc.)see the chart above for information on which holder will fit yourblade size.

DESIGNED TO GIVE YOU GREATER CHATTER-FREERIGIDITY UNDER HEAVY DUTY REQUIREMENTS

Cut-off bladenot included

Right HandShown

KDK Tools1-800-397-0952

SPARE PARTS

9

(OLD STYLE)

No. 0Tool Post

No. 100Tool Post

No. 150Tool Post

No. 200 ToolPost

Part Name Part No. Part No. Part No. Part No.

Shoe (new style)For use on tool posts

purchased prior to 2001specify “O” after part no.

A-0-1 A-100-1 A-150-1 A-200-1

$55 $61 $61 $64

Cam A-0-2 A-100-2 A-100-2 A-100-2

$64 $73 $73 $73

Handle, Assy. Right Hand A-0-4 A-100-4 A-150-4 A-150-4

$37 $43 $47 $47

Knob A-0-5 A-0-5 A-0-5 A-0-5

$4.75 $4.75 $4.75 $4.75

Nylok Button-Head Screw A-0-6 A-0-6 A-0-6 A-0-6

$2.50 $2.50 $2.50 $2.50

Half Dog Point Screw A-0-7 A-0-7 A-0-7 A-0-7

$1.50 $1.50 $1.50 $1.50

Dowel Pin A-0-8 A-0-8 A-150-8 A-150-8

$1.50 $1.50 $1.50 $1.50

Lock Down Bolt A-0-9 A-100-9 A-150-9 A-200-9

$4.75 $5.75 $7.75 $12.50

Spring Washer A-0-11 A-100-11 A-100-11 A-100-11

$2.50 $2.50 $2.50 $2.50

04-1 104-1 154-1 204-1

$28 $30 $32 $38

Clamp Block with Screwsfor Parting Bar

No. 00Tool Post

Part No.

A-00-1

$41

A-00-2

$63

A-00-4

$28

A-00-5

$3.25

A-00-6

$1.75

A-00-7

$1.00

A-00-8

$1.00

A-00-9

$3.50

A-00-11

$1.25

004-1

$25

KDK Tools1-800-397-0952

KDK TOOL POST DIMENSIONS

TOOL POST NUMBER

0 100 150 200

F 3.00" 3.50" 4.37" 5.00"

G 2.25" 2.50" 2.50" 2.87"

H 1.62" 2.25" 2.25" 3.00"

I .312" .312" .312" .312"

J 1.750" 1.750" 1.750" 1.750"

K 1.875" 2.125" 2.125" 2.125"

L .687" .687" .687" .687"

M 7/16" 7/16" 5/8" 3/4"

N 30° 30° 30° 30°

O .312" .331" .331" .331"

P 1/4" 1/4" 5/16" 5/16"

Q .687" .875" 2.312" 2.562"

R 1.343" 1.375" 1.250" 1.437"

00

2.00”

1.62”

1.12”

.187”

1.00”

1.30”

.375”

5/16”

45°

.171”

1/8”

1.00”

.937”

10

ORDERINGINFORMATION

DIMENSIONS NEEDED TO FIT KDK TOOL POSTS TO YOURLATHE

KDK tool posts usually require a riser plate between the tool post and lathe

compound to bring tool to lathe center height. A riser plate, up to 1⅛" thick,

will be furnished FREE if you specity make and model of lathe or furnish

lathe center height. See dimension ‘A’ below. Special riser plates thicker

than 1⅛" furnished at time and material.

NOTE: T-Nuts are not standard for all lathes. To insure correct size, furnish

T-Slot dimensions A, B, C, D, and E (see drawing below), and specify make

and model of lathe.

T-SLOT DIMENSIONS

1-800-397-0952

KDK Tools1-800-397-0952

11

SALES POLICY:SALES TAX:KDK Tools is required to charge applicable State and local sales tax on every item for which a sales tax exemption certificate hasnot been provided. When ordering, please indicate clearly which items are or are not taxable.

RETURNED GOODS:Our authorization to return materials is required. To expedite the issuance of credit, please furnish our invoice number and date ofinvoice. Materials returned due to our error will be promptly credited in full provided they are returned within 30 days and arereceived in original saleable condition. All other returns are subject to charges for inspection or restocking. We cannot acceptmaterials which have been in any way damaged or altered.

SPECIAL GOODS:Orders for nonstandard material/design, special order, or altered at your request cannot be cancelled or returned unlessproduction has not yet begun. If cancelled, customer will be charged for any work done before production is stopped.

CANCELLATIONS:Our permission in writing is required to cancel orders placed with us and are subject to a cancellation charge. Such permissioncan only be granted on the merit of each case.

WARRANTY POLICY:LIMITATION OF REMEDY:Any liability for consequential and incidental damages is expressly disclaimed. The liability of KDK Tools in all events is limited to,and shall not exceed, the purchase price paid.

DELAYS BEYOND SELLER’S CONTROL:Seller shall not be responsible for delays in performance caused by delays in manufacturing, transportation or due to strikes, fires,floods, storms, war, insurrections, riots, any governmental regulation, order, act or instruction, or any circumstances beyond theSeller’s reasonable control. Buyer’s acceptance of goods and/or services shall constitute a waiver of any claims for damages dueto delay. Under no circumstances shall the Seller be liable for any loss or use by Buyer or for any indirect or consequentialdamages arising from such delays.

ERRORS:Clerical and Statistical errors are subject to correction.

LIMITED WARRANTY TO ORIGINAL PURCHASER

KDK Tools warrants all KDK products against defects in material and workmanship to the original purchaser for a period of oneyear from the date the product is delivered to the original purchaser. KDK Tools will repair or replace, at its option, at no charge,any KDK product found to be defective during the warranty period. Such repair or replacements shall not include the costs ofdisassembly, removal, or reinstallation or any other services involved, which costs are the responsibility of the purchaser. Thewarranty repairs must be performed at KDK.

OBLIGATION OF THE ORIGINAL PURCHASER

1. The original dated contract of sale for the KDK product must be retained as proof of purchase and must be presented to theKDK service center.

2. Transportation of the KDK product to and from the service center is the responsibility of the original purchaser who mustprepay transportation and insurance costs.

EXCLUSIONS OF THE WARRANTY

This warranty covers all KDK products under normal use and service and does not cover accident, misuse, fire, flood, other acts ofGod, negligence, alteration, abuse, improper or unauthorized repair and customer adjustments.This warranty is not transferable, is limited to the original purchaser, and is valid only on products purchased, installed and used inthe United States of America.

CONDITIONS:GENERAL:Prices & Discounts are subject to change without notice.

TERMS:2% discount if paid within 10 days of invoice date - NET 30 days. Terms valid on approved credit only.

KDK Tools Reserves the right to delete products, make product improvements, changes, or modifications to all productsmanufactured or sold without incurring any liabilities to incorporate these changes in any part or component - past, present, orfuture.

Every effort has been made to insure that the specifications listed in this catalog are correct. However, KDK Tools does notguarantee the accuracy or correctness of such information listed in this catalog.

The design guidelines & prints in this catalog serve as a reference only.

WARRANTY

KDK Tools1-800-397-0952

Toll Free: 1-800-397-0952Phone: (928) 774-8715

Fax: (800) 779-8188

BULLETIN 6100