1 NAFTA Refinishing Systems (English) · Standocryl® VOC Platinum Clear 16161 VOC Platinum Hardener None 3:1 3.6 (434) Standocryl ® 2K Premium Clear 16252 2K Hardener 2K Thinner

1 NAFTA Refinishing Systems (English)

1-1 US National Rule for Automotive Refinishing

1-2 Bay Area Air Quality Management District - Rule 45

1-3 Mojave Desert Air Quality Management District - Rule 1116, 7/00

2 NAFTA Products

2-1 Hardeners

2-1-1 Hardeners & Thinners

2-2 Surface Preparation

2-2-1 Standohyd VOC Cleaner 25

2-2-2 Standoflex Low VOC Plastic Cleaner

2-2-3 Standohyd Cleaner

2-3 Pretreatment

2-3-1 Standox Etching Adhesion Primer

2-3-2 Standox Low VOC Etching Adhesion Primer

2-3-3 Standox 1K Primer Filler

2-4 Primer / Primer Surfacer

2-4-1 Standox 2.1 Filler

2-4-2 Standox 2K HS System Filler

2-4-3 Standox 2K Nonstop Primer Filler

2-4-4 Standoflex Plastic Primer Silver

2-4-5 Standoflex 2K Plastic Primer Surfacer

2-4-6 Standoflex 1K Plastic Primer

2-5 Primer Sealer

2-5-1 Standox EP Primer Surfacer

2-6 Top Coats

2-6-1 Standox Basecoat

2-6-2 Standox Basecoat Colorless

2-6-3 Standohyd Basecoat

2-7 Clear Coats

2-7-1 Standocryl 2.1 Clear

2-7-2 Standocryl 2.1 HS Clear

2-7-3 Standocryl 2K HS Clear

2-7-4 Standocryl VOC Platinum Clear

2-7-5 Standocryl 2K Plastic Clear Satin Gloss

2-8 Other Products

2-8-1 Standocryl 2K Matt Clear 007

2-8-2 Standox 2K Plasticiser

2-8-3 Standox Smart Blend Plus

2-8-4 Standox 2K Matting Agent Mix 608

Standox® V.O.C. COMPLIANT PRODUCTS

US National Rule for Automotive RefinishingMercedes Benz Approved Products Updated November 06, 2009

SURFACE PREPARATION (No surface preparation limits are set forth in the US National Rule.Please choose from the following cleaners based upon any more stringent VOC Cleaner limits.Product Article Number Hardener Thinner Mix Ratio Applied VOC

lbs/gal - (gms/l)

Standohyd® Cleaner & Aerosol (Aerosol excludes Texas.) 16176/16166 None Included Ready 1.6 (188)/100%Standox® Silicone Remover Antistatic 11654 None Included Ready 6.3 (757)Standoflex® Thinner 11100 16160 None Included Ready 7.2 (859)Standoflex® Low VOC Plastic Cleaner 16010 None Included Ready 0.2 (21)PRETREATMENT (6.5 lbs/gal - 780 g/l limit) Applied VOC LE lbs/galProduct Article Number Hardener Thinner Mix Ratio (g/l) Less water-exemptsStandox® Etching Adhesion Primer 16167 Etching Adhesion Activator Included 1:1 6.4 (760)Standox® 1K Primer Filler 16134 None 2K Thinner 1:50% 6.1 (734)Aerosol version exempt 16141 79%PRIMER / PRIMER SURFACER (4.8 lbs/gal - 580 g/l limit) Applied VOC LE lbs/galProduct Article Number Hardener Thinner Mix Ratio (g/l) Less water-exemptsStandox® 2K HS System Filler 15161/16170 2K Hardener 2K Thinner 4:1+0-10% 4.3 (506)w/ 30% Standox® 2K Plasticiser 15260 15161/16170 2K Hardener 2K Thinner 2:1+0-10% 4.1 (488)Standox® 2K Nonstop Primer Filler 15331/16153/16154 2K Hardener 2K Thinner 3:1+15-20% 4.7 (556)As an Isolator 15331/16153/16154 2K Hardener 2K Thinner 3:1+25% 4.8 (572)w/ 30% Standox® 2K Plasticiser 15260 15331/16153/16154 2K Hardener 2K Thinner 3:1+15-20% 4.4 (525)Standox® 2.1 Filler 11999 2K Hardener 2K Thinner 4:1+20-30% 4.2 (495)w/ 30% Standox® 2K Plasticiser 15260 11999 2K Hardener 2K Thinner 2:1+20-30% 4.2 (508)Standox® EP Primer 16183 EP Hardener 2K Thinner 3:1+25% 4.7 (569)PRIMER SEALER (4.6 lbs/gal - 550 g/l limit) Applied VOC LE lbs/galProduct Article Number Hardener Thinner Mix Ratio (g/l) Less water-exempts2K Transparent Adhesion Sealer 15048 2K Hardener 2K Thinner (except 2K 35-40) 3:1+20% 4.6 (550)2K Nonstop Primer Filler 15331/16153/16154 2K Hardener 2K Thinner (except 2K 35-40) 3:1+20% 4.6 (550)w/ 15% Standox® 2K Plasticiser 15260 15331/16153/16154 2K Hardener 2K Thinner 3:1+20% 4.5 (539)TOPCOATS - SINGLE STAGE (5.0 lbs/gal - 600 g/l limit) Applied VOC LE lbs/galProduct Article Number Hardener Thinner Mix Ratio (g/l) Less water-exemptsStandocryl® 2K MS Paint See price list 2K Hardener 2K Thinner 2:1+0-10% 4.7 (563)Standocryl® 2K MS Paint w/15-30% 2K Plasticiser 15260 2K Hardener 2K Thinner 2:1+0-10% 4.6 (546)TOPCOATS - TWO-STAGE (5.0 lbs/gal - 600 g/l limit) Applied VOC LE lbs/galProduct Article Number Hardener Thinner Mix Ratio (g/l) Less water-exemptsStandox® Basecoat or None MSB Thinner 1+50% BC+2*CC/3Standox® Factory Pack Deep Black None MSB Thinner (no 30-45) 1+70%

with the following clears:Standocryl® 2K Clear 15-60 PLUS 16198 2K Hardener 2K Thinner or 2K Fast Dry Additive 2:1+0-5% 5.0 (600)Standocryl® 2K HS Clear 14580 2K Hardener 2K Thinner or 2K Fast Dry Additive 2:1+0-5% 4.9 (585)Standocryl® 2K Premium Clear 16252 2K Hardener 2K Thinner or 2K Fast Dry Additive 2:1+0-10% 5.0 (600)Standocryl® 2K Clear 15-60 15900 2K Hardener None 2:1 5.0 (600)Standocryl® VOC Platinum Clear 16161 VOC Platinum Hardener None 3:1 4.7 (561)Standohyd® Basecoat (See price list for Article #s.) None Standohyd® VE Water 1+0-15%

withStandocryl® 2K HS Clear 14580 2K Hardener 2K Thinner 2:1+0-10% 4.0 (470)Standocryl® VOC Platinum Clear 16161 VOC Platinum Hardener None 3:1 3.6 (435)Standocryl® 2K Premium Clear 16252 2K Hardener 2K Thinner 2:1+0-10% 4.0 (472)GM 4901M RecommendationStandox® Basecoat with 2K Hardener MSB Thinner 1+15%+30-40%Standocryl® 2K HS Clear 14580 2K Hardener 2K Thinner or 2K Fast Dry Additive 2:1+0-5% 4.9 (583)Standocryl® 2K Premium Clear 16252 2K Hardener 2K Thinner or 2K Fast Dry Additive 2:1+0-10% 5.0 (600)Standocryl® 2K Clear 15-60 15900 2K Hardener None 2:1 5.0 (600)THE ABOVE CLEARCOATS (not Platinum) MAY BE MIXED WITH 15-30% 2K PLASTICISER FOR USE ON PLASTIC PARTS & COMPLY UNDER THIS CATEGORY.TOPCOATS - TRI-STAGE (5.2 lbs/gal - 630 g/l limit) Applied VOC LE lbs/galProduct Article Number Hardener Thinner Mix Ratio (g/l) Less water-exemptsStandox® Basecoat (See price list for Article #s.) with None MSB Thinner 1+50% BC*2+CC*2/4Standocryl® 2K Premium Clear 16252 2K Hardener None 2:1 5.2 (629)Standocryl® VOC Platinum Clear 16161 VOC Platinum Hardener None 3:1 5.2 (622)Standocryl® 2K HS Clear 14580 2K Hardener None 2:1 5.2 (627)Standohyd® Basecoat (See price list for Article #s.) None Standohyd® VE Water 1+0-10%

withStandocryl® 2K HS Clear 14580 2K Hardener 2K Thinner or 2K Fast Dry Additive 2:1+0-5% 3.8 (446)Standocryl® VOC Platinum Clear 16161 VOC Platinum Hardener None 3:1 3.6 (434)Standocryl® 2K Premium Clear 16252 2K Hardener 2K Thinner or 2K Fast Dry Additive 2:1+0-10% 3.9 (459)ALL OF THE ABOVE CLEARCOATS (not Platinum) MAY BE MIXED WITH 15-30% 2K PLASTICISER FOR USE ON PLASTIC PARTS & COMPLY UNDER THIS CATEGORY.SPECIALTY COATINGS (7.0 lbs/gal - 840 g/l limit) Applied VOC LE lbs/galProduct Article Number Hardener Thinner Mix Ratio (g/l) Less water-exempts

Adhesion Promoters Standox® 2K Nonstop Primer Filler 15331/16153/16154 2K Hardener 2K Thinner 3:1+30% 4.9 (586)Standox® 2K Transparent Adhesion Sealer 15048 2K Hardener 2K Fade-Out Thinner 3:1+30% 4.9 (584)Standox® EP Primer 16183 EP Hardener 2K Thinner 3:1+25% 4.7 (569)

Elastomeric MaterialStandoflex® 2K Plastic Primer Surfacer 11816 2K Plastic Hardener None 1:1 5.6 (674)Standoflex® 1K Plastic Primer (Silver) & Aerosol 12065/14408 None None Ready 7.0 (838)/<2.5 MIR2K Opel 215 Rallye Black Matt 10887 2K Hardener 2K Thinner 3:1+0-10% 4.5 (541)Standocryl® 2K Matt Clear 007 (alone or per TDS) 16163 2K Hardener 2K Thinner 3:1+0-25% 4.8 (571)2K MS Standocryl® with 80% Standox® 2K Matting Agent Mix 606 13649 2K Hardener 2K Thinner 3:1+0-10% 4.9 (592)

Fish Eye EliminatorStandox® 2K Topcoats with 2% (highest possible) 11107 RTS RTS RTS+2% 4.2 (507)

Uniform Finish BlenderStandox® BC Colorless (alone or 2:1 with BC) 16150 None None Ready 6.7 (801)Standox® BC Colorless (Matt over Standohyd® BC) 16150 2K Hardener None 1+15% 4.5 (545)Standohyd® Special Effect Color Blend 60213 None None Ready 1.9 (233)Standohyd® Color Blend 80045 None None Ready 2.6 (319)Standox® Smart Blend Plus 16174 Ready-to-Spray 2K Clear None 4:1 6.7 (806)Standox® 2K Fade-Out Thinner 11247 Ready-to-Spray 2K Clear None 3:1 7.0 (840)OTHER PRODUCTSStandohyd® Sanding Paste 14670Standox® PE Spray Filler 16177HARDENERS THINNERS 2K Hardener 05-15 15080/16145 Thinner 2K 35-40 (>95F) 11921 2K Hardener 15-25 15013 MS Thinner 2K 25-35 (80-95F) 11484 2K Hardener 20-30 15978/16146 Express Thinner 2K 15-25 (60-80F) 11182 2K Hardener 25-40 15935 Rapid Thinner 2K 10-20 (<60F) 11573 2K Hardener 30-45 15943 2K Fast Dry Additive 16169

MSB Thinner 30-45 (>90F) 16158 MSB Thinner 25-40 (75-95F) 19523 MSB Thinner 20-30 (70-85F) 11387 MSB Thinner 15-25 (59-75F) 12049 MSB Thinner 05-15 (<60F) 11395For Jurisdiction, Applicability, Solvent Handling, Recordkeeping, Exemptions or more specific information, see the Standox® TDS, MSDS, or contact 800-551-9296 ext 3416Copyright© 2009 DuPont. Standox®, Standohyd®, Standocryl® and Standoflex® are registered trademarks of E.I. du Pont de Nemours and Company for its brands of refinish systems. All rights reserved.

Also covers: Delaware- DNR Reg. 24 Sec 11; / Illinois-EPA Title 35, Admin. Code Part 218, Subpart HH / Indiana-D.E.M. Title 326 IAC 8-10/ Jefferson Co.-APCD Reg. 6.44/ Maricopa Co.APC Arizona, Rule 345/ Massachusetts-Rule 310 CMR 7.28(28)/ Maryland-D.E.Comar 26.11.19.23/ New Jersey AC 7:27-16.12-New York State Part 228 (Jan1, 05), Penn. DEP, Rule 121/ Portland-AQMA OAR340-22-720/ Rhode Island-APC Reg. No.30/ Tennesse-APCB Rule 1200-3-18-45/ TCEQ 30 TAC Ch. 115/Puget Sound-APCA Reg. 9.16/ Spokane Co.-APCA Reg. I Sec 6.13/ Vancover,WA-SWAPCA 493-400/ Wisconsin-NRB Rule NR 422.095

Must use 16176/16166 for metal: Illinois, Indiana, Jefferson County-KY, Nashville-TN, Massachusetts, Maricopa Cnty (PHX area), Rhode Island, Puget Sound, Spokane, Texas, Wisconsin.Must use 11654/16010 for cleaning of plastics (16160 is not allowed): Illinois, Indiana, Maryland, Rhode Island, Spokane, Wisconsin.Must use 16010 for cleaning of plastics (no other cleaners allowed): Jefferson Cty KY, Nashville TN, Maricopa Cty, Massachusetts, Texas.

Standox® V.O.C. COMPLIANT PRODUCTSBay Area Air Quality Management District - Rule 45 - Effective 1/1/2010Mercedes Benz Approved Products

Updated January 8, 2010

SURFACE PREPARATION 0.2 lbs/gal-25 g/l Applied VOCProduct Article Number Hardener Thinner Mix Ratio lbs/gal - (gms/l)Bay Area (LIMIT 0.2 lbs/gal - 25g/l)Standohyd® Cleaner (limitations based on usage - LIMIT 350 g/l) 16176 None None Ready 1.6 (188)Standohyd® VOC Cleaner 25 16178 None None Ready 0.2 (25)Standoflex® Low VOC Plastic Cleaner 16010 None None Ready 0.2 (21)

PRETREATMENT (5.5 lbs/gal-660 g/l limit) Applied VOC LE lbs/galProduct Article Number Hardener Thinner Mix Ratio (g/l) Less water-exempts

Standox® Low VOC Etch Primer 16189Low VOC Etch Primer Activator Included 2:1 5.3 (635)

Standox® 1K Primer Filler Light Gray - Aerosol 16141 None None Ready ExemptPRIMER / PRIMER SURFACER (2.1 lbs/gal-250 g/l limit) Applied VOC LE lbs/galProduct Article Number Hardener Thinner Mix Ratio (g/l) Less water-exemptsStandox® 2.1 Filler 11999 2.1 Hardener 2.1 Thinner 4:1+20-30% 2.1 (250)Standox® 2.1 Filler w/ 30% 2K Plasticiser 15260 11999 2.1 Hardener 2.1 Thinner 2:1+20-30% 2.1 (248)PRIMER SEALER (2.1 lbs/gal-250 g/l limit) (Effective 1/1/2010) Applied VOC LE lbs/galProduct Article Number Hardener Thinner Mix Ratio (g/l) Less water-exemptsStandox® 2.1 Filler with Sealer Agent 11999/16171 2.1 Hardener 2.1 Thinner 2+1+30%+10-20% 2.0 (240)with Plasticiser 2+15% Plasticiser (15260) 11999/16171 2.1 Hardener 2.1 Thinner 2+15%:1+30%+10% 2.0 (238)Standox® Low VOC Sealer 16182/16171 2.1 Hardener 2.1 Thinner 2:1+30%+10-20% 2.0 (240)with Plasticiser 2+15% Plasticiser (15260) 16182/16171 2.1 Hardener 2.1 Thinner 2+15%:1+30%+10% 2.0 (235)Standox® 2K EP Primer (Aerosol) 16181 None Included Ready ExemptCOLOR COATING (3.5 lbs/gal-420 g/l limit) Applied VOC LE lbs/galProduct Article Number Hardener Thinner Mix Ratio (g/l) Less water-exemptsStandohyd® Basecoat (See price list for Article #s.) None Standohyd® VE Water 1+0-10% 3.5 (420)

With a humidity of 30% or lower, and temperatures equal or higher than 95F / 35C, Standohyd® LH Thinner (Low Humidity) can be used as a replacement for Standohyd® VE Water (0-10%).

5% (by vol.) of Standohyd® Special Additive can be added to two-stage basecoats and the ground coat of three-stage formulas. Basecoats activated with Standohyd ® Special Additive for interior applications will require a matte clearcoat layer.CLEAR COATING (2.1 lbs/gal-250 g/l limit) Applied VOC LE lbs/galProduct Article Number Hardener Thinner Mix Ratio (g/l) Less water-exemptsStandocryl® 2.1 Clear 10020 2.1 Hardener 2.1 Thinner 2:1+0-10% 2.1 (249)Standocryl® 2.1 HS Clear 16156 2.1 Hardener 2.1 Thinner 2:1+0-10% 1.9 (230)Standocryl® 2.1Clear or 2.1 HS Clear w/15-30% 2K Plasticiser 15260 2.1 Hardener 2.1 Thinner 2:1+0-10% 2.1 (246)VOC compliancy can still be realized when adding up to 2% (by volume) of Silistop (11107) to 2.1 Clearcoats.Standox® 2K Matting Agent Mix 608 16199 2.1 Hardener 2.1 Thinner 2:1+5-10% 2.0(241)3:1 with Standox 2.1 Clear (10020) or Standox 2.1 HS Clear (16156)UNIFORM FINISH COATINGS (4.5 lbs/gal-540 g/l limit) Applied VOC LE lbs/galProduct Article Number Hardener Thinner Mix Ratio (g/l) Less water-exemptsStandox® 2K Smart Blend Plus 16174 11778 10097

161742:1+0-10%+50% 4.5 (540)

* With only activated Standocryl® 2.1 Clear (10020) and 2.1 HS Clear (16156) mixed as per the manufacturer's instructions provided here.

Standohyd® Color Blend 80045Ready-to-Spray Standohyd® Basecoat

None 1:1 3.1 (372)

Standohyd® Special Effect Color Blend 60213 None None Ready 1.9 (233)ADHESION PROMOTER (4.5 lbs/gal-540 g/l limit) (Effective 1/1/2010) Applied VOC LE lbs/galProduct Article Number Hardener Thinner Mix Ratio (g/l) Less water-exemptsStandoflex® 1K Plastic Primer 16202 None None Ready 4.0 (476)

Standoflex® Plastic Primer Silver (Aerosol) 14408 None None Ready ExemptOTHER PRODUCTSStandohyd® Sanding Paste 14670Standox® PE Spray Filler 16177

HARDENERS Exempt Solvent Thinners 2.1 Hardener - Extra Slow 16125 2.1 Thinner - Slow 16133

2.1 Hardener - Slow 16117 2.1 Thinner - Normal 100972.1 Hardener - Normal 10089 2.1 Thinner - Fast 11786

2.1 Hardener - Fast 11778

For Jurisdiction, Applicability, Solvent Handling, Recordkeeping, Exemptions or more specific information, see the Standox® TDS, MSDS, or contact 800-551-9296 ext 3416. Copyright© 2009 DuPont. Standox®, Standohyd®, Standocryl® and Standoflex® are registered trademarks of E.I. du Pont de Nemours and Company for its brands of refinish systems.All rights reserved.

2 Parts 10020 or 16156, 1 Part 11778, + 10% 10097, + 0-50% 16174

Standox® V.O.C. COMPLIANT PRODUCTSMojave Desert Air Quality Management District - Rule 1116, 7/00Mercedes Benz Approved Products

Updated November 6, 2009

SURFACE PREPARATION 0.2 lbs/gal-25 g/l Applied VOCProduct Article Number Hardener Thinner Mix Ratio lbs/gal - (gms/l)Standohyd® Cleaner (Aerosol) 16166 None None Ready ExemptStandohyd® VOC Cleaner 25 16178 None None Ready 0.2 (25)Standoflex® Low VOC Plastic Cleaner 16010 None None Ready 0.2 (21)PRETREATMENT (6.5 lbs/gal-660 g/l limit) Applied VOC LE lbs/galProduct Article Number Hardener Thinner Mix Ratio (g/l) Less water-exemptsStandox® Low VOC Etch Primer 16189 Low VOC Etch Primer Activator Included 2:1 5.3 (635)Standox® Etching Adhesion Primer 16167 Etching Adhesion Activator Included 1:1 6.3 (764)

Standox® 1K Primer Filler/Aerosol 16134/16141 None 2K Thinner 1:50% 6.1 (734)/79%PRIMER / PRIMER SURFACER (2.1 lbs/gal-780 g/l limit) Applied VOC LE lbs/galProduct Article Number Hardener Thinner Mix Ratio (g/l) Less water-exemptsStandox® 2.1 Filler 11999 2.1 Hardener 2.1 Thinner 4:1+20-30% 2.1 (250)Standox® 2.1 Filler w/ 30% 2K Plasticiser 15260 11999 2.1 Hardener 2.1 Thinner 2:1+20-30% 2.1 (248)PRIMER SEALER (2.8 lbs/gal-340 g/l limit) Applied VOC LE lbs/galProduct Article Number Hardener Thinner Mix Ratio (g/l) Less water-exemptsStandox® 2.1 Filler with Sealer Agent 11999/16171 2.1 Hardener 2.1 Thinner 2+1+30%+10-20% 2.0 (240with Plasticiser 2+15% Plasticiser (15260) 11999/16171 2.1 Hardener 2.1 Thinner 2+15%:1+30%+10% 2.0 (238)Standox® 2K EP Primer (Aerosol) 16181 None Included Ready 66%TOPCOATS - TWO-STAGE (3.5 lbs/gal-420 g/l limit)

Product Article Number Hardener Thinner Mix RatioStandox® Basecoat (See price list for Article #s.) with None MSB Thinner 1+50%Standocryl® 2.1 Clear/2.1 HS Clear or 10020/16156 2.1 Hardener 2.1 Thinner 2:1+0-10% 3.5 (420)Standocryl® 2.1 Clear/2.1 HS Clear w/15-30% 2K Plasticiser 15260 2.1 Hardener 2.1 Thinner 2:1+0-10% 3.5 (418)Standohyd® Basecoat (See price list for Article #s.) with None Standohyd® VE Water 1+0-10%

With a humidity of 30% or lower, and temperatures equal or higher than 95F / 35C, Standohyd ® LH Thinner (Low Humidity) can be used as a replacement for Standohyd® VE Water (0-10%).

5% (by vol.) of Standohyd® Special Additive can be added to two-stage basecoats.

Basecoats activated with Standohyd® Special Additive for interior applications will require a matte clearcoat layer.

Standocryl® 2.1 Clear/2.1 HS Clear or 10020/16156 2.1 Hardener 2.1 Thinner 2:1+0-10% 2.6 (306)Standocryl® 2.1 Clear/2.1 HS Clear w/15-30% 2K Plasticiser 15260 2.1 Hardener 2.1 Thinner 2:1+0-10% 2.6 (304)Standox® 2K Matting Agent Mix 608 16199 2.1 Hardener 2.1 Thinner 2:1+5-10% 2.6 (314)3:1 with Standox 2.1 Clear (10020) or Standox 2.1 HS Clear (16156)Standocryl® VOC Platinum Clear 16161 2.1 Hardener None 2:1 3.5 (419)Standocryl® 2K HS Clear or 14580 2.1 Hardener 2.1, 2K Thinner 2:1+0-10% 3.5 (420)Standocryl® 2K HS Clear w/15-30% 2K Plasticiser 15260 2:1+0-10% 3.5 (414)GM 4901M RecommendationStandox® Basecoat (See price list for Article #s.) with 2.1 Hardener MSB Thinner 1+15%+30-40%Standocryl® 2.1 Clear/2.1 HS Clear 10020/16156 2.1 Hardener 2.1 Thinner 2:1+0-10% 3.5 (420)TOPCOATS - TRI-STAGE (3.5 lbs/gal-420 g/l limit)

Product Article Number Hardener Thinner Mix RatioStandox® Basecoat (See price list for Article #s.) with None 2.1 Thinner Normal 1+50%Standocryl® 2.1 Clear/2.1 HS Clear or 10020/16156 2.1 Hardener 2.1 Thinner 2:1+0-10% 3.5 (420)Standocryl® 2.1 Clear/2.1 HS Clear w/15-30% 2K Plasticiser 15260 2.1 Hardener 2.1 Thinner 2:1+0-10% 3.5 (418)Standohyd® Basecoat (See price list for Article #s.) with None Standohyd® VE Water 1+0-10%

With a humidity of 30% or lower, and temperatures equal or higher than 95F / 35C, Standohyd ® LH Thinner (Low Humidity) can be used as a replacement for Standohyd® VE Water (0-10%).

5% (by vol.) of Standohyd® Special Additive can be added to the ground coat of three-stage formulas.

Basecoats activated with Standohyd® Special Additive for interior applications will require a matte clearcoat layer.Standocryl® 2.1 Clear/2.1 HS Clear or 10020/16156 2.1 Hardener 2.1 Thinner 2:1+0-10% 2.8 (334)Standocryl® 2.1 Clear/2.1 HS Clear w/15-30% 2K Plasticiser 15260 2.1 Hardener 2.1 Thinner 2:1+0-10% 2.8 (328)Standox® 2K Matting Agent Mix 608 16199 2.1 Hardener 2.1 Thinner 2:1+5-10% 2.8 (341)3:1 with Standox 2.1 Clear (10020) or Standox 2.1 HS Clear (16156)Standocryl® VOC Platinum Clear 16161 2.1 Hardener None 2:1 3.5 (419)Standocryl® 2K HS Clear or 14580 2.1 Hardener 2.1, 2K Thinner 2:1+0-10% 3.5 (420)Standocryl® 2K HS Clear w/15-30% 2K Plasticiser 15260 2:1+0-10% 3.5 (415)SPECIALTY COATINGS (7.0 lbs/gal-840 g/l limit)

Product Article Number Hardener Thinner Mix RatioUniform Finish Blenders

Standohyd® Color Blend 80045 Ready-to-Spray Standohyd®

BasecoatNone 1:1 3.1 (372)

Standox® BC Colorless (alone or 2:1 w/BC) 16150 None None Ready 6.7 (801)Standox® BC Colorless (Matt over Standohyd BC) 16150 2.1 Hardener None 1+15% 4.2 (506)Standohyd® Color Blend 80045 None None Ready 2.6 (318)Standohyd® Special Effect Color Blend 60213 None None Ready 1.9 (233)Standox® 2K Fade-Out Thinner/2K Smart Blend 11247/16157 Ready-to-Spray 2K Clear None 3:1 6.9 (831)

Elastomeric CoatingsStandoflex® 2K Plastic Primer Surfacer 11816 2K Plastic Hardener None 1:1 5.6 (674)Standoflex® 1K Plastic Primer (Silver) 12065 None None Ready 7.0 (838)Standoflex® 1K Plastic Primer 16202 None None Ready 4.0 (476)Standocryl® 2K Opel 215 Ralleye Black Matt 10887 2.1 Hardener 2K Thinner 3:1+0-10% 4.1 (491)Standocryl® 2K Matt Clear 007 (alone or per TDS) 16163 2.1 Hardener 2K Thinner 3:1+0-25% 3.4 (409)OTHER PRODUCTSStandohyd® Sanding Paste 14670Standox® PE Spray Filler 16177

HARDENERS THINNERS Exempt Solvent Thinners 2.1 Hardener - Extra Slow 16125 Thinner 2K 35-40 (>95F) 11921 2.1 Thinner - Slow 16133

2.1 Hardener - Slow 16117 MS Thinner 2K 25-35 (80-95F) 11484 2.1 Thinner - Normal 100972.1 Hardener - Normal 10089 Express Thinner 2K 15-25 (60-80F) 11182 2.1 Thinner - Fast 11786

2.1 Hardener - Fast 11778 Rapid Thinner 2K 10-20 (<60F) 115732K Fast Dry Additive 16169

MSB Thinner 25-40 (75-95F) 19523MSB Thinner 20-30 (70-85F) 11387MSB Thinner 15-25 (59-75F) 12049

MSB Thinner 05-15 (<60F) 11395For Jurisdiction, Applicability, Solvent Handling, Recordkeeping, Exemptions or more specific information, see the Stand® TDS, MSDS, or contact 800-551-9296 ext 3416. Copyright© 2009 DuPont. Standox®, Standohyd®, Standocryl® and Standoflex® are registered trademarks of E.I. du Pont de Nemours and Company for its brands of refinish systems. All rights reserved.

Applied VOC LE lbs/gal (g/l) Less water-exempts



© 2013 Axalta Coating Systems, LLC and all affiliates. All rights reserved. 07/24/2013

This list represents a comparison of flash-off and drying characteristics of Standox Hardeners. Hardeners should only be used as specified on the technical data sheets. Flash-off time and drying are dependent upon film thickness. Higher film builds will produce longer flash-off and slower dry times. Temperatures shown only provide a reference point. Actual temperature, humidity, air movement, size of the refinish area, and location of the refinish area will affect hardener choice. Please see appropriate VOC Wallchart for 2K, 2.1 or PF Hardener choice.

2K HARDENERS

PF HARDENERS

SLOWEST Hardener PFH 30-35 16214

Slowest flash-off PF Hardener Temperature range: 86-95°F (30-35°C)

Hardener PFH 25 – 30 16213

Faster than PF 30-35. Temperature range: 77-86°F (25-30°C)

FASTEST

Hardener PFH 15 – 25 16212

Fastest flash-off of PF Hardeners Temperature range: 59-77°F (15-25°C)

SLOWEST 2K HARDENER H 30-45

16147 Slower than H 25-40 Temperature range: above 95°F (above 32°C)

2K HARDENER H 25-40 15935

Slower than H 20-30 Temperature range: 75-90°F (24-32°C)

2K HARDENER H 20-30

15978 For larger areas or normal temperatures. Temperature range: 70-85°F (20-30°C)

2K HARDENER H 15-25

15013 Faster flash-off than H 20-30. Temperature range: 59-75°F (15-24°C)

FASTEST

2K HARDENER H 05-15

15080 Fastest flash-off 2K Hardener For spot repairs and cool temperatures. Temperature range: 41-77°F (5-25°C)

Standox®

Charts & Systems Hardeners


This table represents a comparison of the flash-off characteristics of Standox Thinners. Do not mix 2K Thinners

with MSB Thinners. Flash-off time and drying are dependent upon film thickness. Higher film builds will produce longer flash-off and slower dry times.

2K THINNERS: DESIGNED FOR 2K MATERIAL / DO NOT MIX WITH MSB THINNERS

SLOWEST 2K THINNER T30-35 (86-95°F)

16206

Slowest flash-off thinner. For use in higher temperatures and complete resprays. Specifically recommended in the Special Matt (16205)

2K THINNER T25-35 (80-95°F)

11484

Slow flash-off thinner. For use in higher temperatures and complete resprays.

2K THINNER T15-25 (60-80°F)

11182

Normal flash-off thinner. Can be used for single panels and complete resprays.

FASTEST

2K THINNER T10-20 (<60°F)

11573

Fastest flash-off 2K thinner. Ideal for low temperatures and small repairs.

MSB THINNERS: DESIGNED FOR BASECOAT / DO NOT MIX WITH 2K THINNERS

SLOWEST MSB THINNER BC 30-45 (>90°F)

16158

Extremely Slow flash-off thinner. For extreme heat and humidity.

MSB THINNER BC 25-40 (75-95°F)

19523

Slow flash-off thinner. Designed for hot (tropical) conditions.


11387

Normal flash-off thinner. Slightly slower in flash-off than MSB 15-25. Designed for small repairs to complete resprays in normal to above normal temperatures


12049

Fast flash-off thinner. Designed for small repairs to multiple panel resprays in normal temperatures.

FASTEST

MSB THINNER BC 05-15 (<60°F)

11395

Fastest flash-off thinner. Designed for lower temperatures.

PF THINNER: DESIGNED FOR 2K MATERIALS

PF Thinner

16215 Used in all temperature ranges.

PF Reaction Agent


PF Reaction Agent Slow


Standox®

Charts & Systems Thinners


2K Smart Blend Plus 16174 2K Fade-Out Thinner 11247

Specialty solvents designed for 2K Blending procedures. Only use per specified technical recommendations. Not recommended for use as a retarder.

2K Fast Dry Additive 16169 A specialty additive for 2K HS Clear (14580), 2K Clear 15-60 Plus (16198) and 2K Premium Clear (16252) that speeds up the flash-off and baking process. See appropriate VOC Wallchart for compliancy in your area.

Standohyd® VE Water 80184 Use only for thinning Standohyd products to ensure proper product

performance.

Standoblue Viscosity Adjuster (19302)

Use only for thinning Standoblue products to ensure proper product performance.

Standoblue Viscosity Adjuster Slow (19303)

Use only for thinning Standoblue products to ensure proper product performance.

STANDOBLUE VISCOSITY ADJUSTER SELECTION CHART

Te

mpe

ratu

re °F

/C°

Relative Humidity %

<10% 10-20% 20-30% >30%

Less Than

95°F (35°C) Viscosity Adjuster

Viscosity Adjuster

Viscosity Adjuster

Viscosity Adjuster

Equal to or Grater than

95°F (35°C) Viscosity Adjuster

Slow

Viscosity Adjuster

Slow

Viscosity Adjuster

Slow

Viscosity Adjuster

Thinners

Standox®

Charts & Systems

MISC. THINNERS


Standohyd® VOC Cleaner 25

Ordering Information: 3.5 Liter Standohyd VOC Cleaner 25 020 16178

Features:

Waterborne Silicone Remover VOC Compliant for 25 g/l VOC limits.

Working Process: Low VOC Cleaner

Substrates: Bare metal-aluminum-galvanized metal, sanded Standox polyesters, sanded Standox fillers, sanded

Through-hardened, sanded paintwork

Apply by spray bottle or soaked cloth. Remove with a clean, dry cloth.

Use air jet to blast residual moisture from corners and crevices. Ventilate surfaces well before further treatment.

Important Technical Remarks:

Shake well before use.

Protect from freezing!

Use Standohyd VOC Cleaner 25 or Standohyd Cleaner before all waterborne product applications.

Do not allow Standohyd VOC Cleaner 25 to dry on surfaces.

Change cloths often. For cloth recommendations, please refer to the Sontara® chart in Charts & Systems.

Important Legislative Remarks:

Please see the appropriate VOC Wallchart for compliance for your area. The values depicted below are ready to spray.

VOC Category

VOC Regulatory & Actual

Density g/l Wt% Volatiles, Water & Exempts

Vol% Water & Exempts

Surface Preparation 0.2 lb/gal - 25 g/l 960 g/l 100%, 14.7%, 82.7% 97.5%

For industrial use only by professional, trained painters. Not for sale to or use by the general public. Before using, read and follow all label and MSDS precautions. If mixed with other components, mixture will have hazards of all components. Do not sand, flame cut, braze or weld dry coating without a NIOSH approved air purifying respirator with particulate filters or appropriate ventilation, and gloves.

Any analytical results set forth herein do not constitute a warranty of specific product features or of the product’s suitability for a specific purpose. All products are sold pursuant to our general conditions of sale. We hereby disclaim all warranties and representations, express or implied, with respect to this product, including any warranty of merchantability or fitness for a particular purpose. This product is protected by patent law, trademark law, copyright law, international treaties and/or other applicable law. All rights reserved. Unauthorized sale, manufacturing or use may result in civil and criminal penalties.

105


Standoflex® Low VOC Plastic Cleaner

Ordering Information: 20 oz. Low VOC Plastic Cleaner 020 16010

Features: Cleaning of bare plastic substrates Special cleaning properties-shorter and more efficient preparation process. Eliminates the tempering process.

Working Process: Cleaner for Plastics

Substrates: Bare plastic parts

Pre-clean plastic with water, Standoflex Low VOC Plastic Cleaner and a clean, gold scuff pad.

Clean 2-3 times using fresh Standoflex Low VOC Plastic Cleaner and

clean, gold scuff pads. For hard to reach areas, the attached brush should be used. Rinse thoroughly with plenty of clean water until all residue is removed. .

Final clean with Standohyd® Cleaner (16176), Standox VOC Cleaner 25

(16178) or Standox® Silicone Remover Antistatic (16203).


Cleaning is the most important task in plastic refinishing and should be observed for optimum adhesion for some types of plastics, i.e. PUR and GRP.


Low VOC waterborne product with special cleaning properties.

Replaces the need for a soap and water step.

Rinse thoroughly and remove all residues. The use of a clean, gold scuff pad will facilitate rinsing.

Use supplied brush for hard to reach areas.

Once cleaning is completed, proceed to paint process.


Please see the appropriate VOC Wallchart for compliance for your area. The values depicted below are “ready to spray”.

VOC Category Surface Preparation




Plastic Prep Gel – 20 Oz. 13 g/l 1494 g/l 27.6%, 26.7%,

0%

40.1%



106


Standohyd® Cleaner

Ordering Information: 5.0 Liter Standohyd Cleaner 020 16176

Features:

Waterborne Silicone Remover VOC compliant for those areas with cleaner limits of < 1.67 lbs/gal (200 g/l) Excellent antistatic properties

Working Process: Low VOC Cleaner

Substrates: Bare metal-aluminum-galvanized metal, sanded Standox polyesters, sanded Standox fillers, sanded


Apply by spray bottle or soaked cloth. Remove with a clean, dry cloth.

Use air jet to blast residual moisture from corners and crevices. Ventilate surfaces well before further treatment.


Shake well before use.


Use Standohyd Cleaner (or Standohyd VOC Cleaner 25) before all waterborne product applications.

Do not allow Standohyd Cleaner to dry on surfaces.

Change cloths often. For cloth recommendations, please refer to the Sontara® chart on page 8 in Charts &

Systems.



VOC Category




Surface Preparation 188g/l 947 g/l 99.9%, 80%, 0% 75.9%



107

2009 Edition 1 Page 6 Copyright© 2009 DuPont. Standox®, Standoflex®, Standohyd® and Standocryl® are registered trademarks of E.I. du Pont de Nemours and

Company for its brands of refinish systems. All rights reserved.

Standox® Etching Adhesion Primer Ordering Information: 1 Liter Etching Adhesion Primer 020 16167 1 Liter Etching Adhesion Activator 020 16168 Features:

2K Acid Primer Excellent adhesion Chromate free Outstanding corrosion protection

Working Process: Pretreatment Etch Primer

Substrates: Through-hardened, sanded paintwork Bare metal- aluminum-galvanized metal, sanded and thoroughly cleaned Standox Polyesters, sanded (for adhesion in case of sand-throughs)

Sand and clean repair area thoroughly. For sensitive substrates, carry out a solvent test.

For substrate preparation information see Standox Painting System S1!

1:1 with Etching Adhesion Activator potlife 8 h /68°F (20°C)

Ready to spray

1.3 - 1.4 mm 2 coats = 0.32 mil (8 micron) Please refer to gun manufacturer and local legislation for proper spray pressure recommendations.

1.2 - 1.3 mm 2 coats = 0.32 mil (8 micron) Please refer to gun manufacturer and local legislation for proper spray pressure recommendations. 30 min/ 68°F (20°C)

Standox 2K Fillers

312

Approved Transfer Efficiency



Standox® Etching Adhesion Primer Important Technical Remarks: • Etching Adhesion Primer must be applied in combination with Standox 2K Fillers. • Do not overcoat with Polyester, Epoxy or Standohyd® products. • For aluminum substrates, use only freshly mixed material. After sanding and cleaning the aluminum, prime

immediately to prevent oxidation and adhesion failure. • Overcoat Standox Etching Adhesion Primer with a Standox 2K Filler within 72 hours. After 72 hours without

sanding, re-apply one coat of Standox Etching Adhesion Primer and overcoat with a Standox 2K Filler. • Facilities enrolled in the Warranty program must use a Standox 2K Filler over Standox Etching Adhesion Primer

for Warranty repairs. • Do not add thinners. Important Legislative Remarks: • Please see the appropriate VOC Wallchart for compliance for your area. The values depicted below are “as

applied regulatory for the coating. Values have been determined using EPA Test Method 24. Please see the Master Values List for information on individual components.

VOC Category Pretreatment Coating

VOC Regulatory 6.5 lbs/gal – 780 g/l

Density g/l

Wt% Volatiles, Water & Exempts


Pretreatment Coating 16167 6.4 lbs/gal - 760 g/l 927 g/l 82.3%, 1.1%, &, 0.0%

1.0%

• Contains acid. May cause eye burns. • For industrial use only by professional, trained painters. Not for sale to or use by the general public.

Before using, read and follow all label and MSDS precautions. If mixed with other components, mixture will have hazards of all components. Do not sand, flame cut, braze or weld dry coating without a NIOSH approved air purifying respirator with particulate filters or appropriate ventilation, and gloves.

• Any analytical results set forth herein do not constitute a warranty of specific product features or of the product’s suitability for a specific purpose. All products are sold pursuant to our general conditions of sale. We hereby disclaim all warranties and representations, express or implied, with respect to this product, including any warranty of merchantability or fitness for a particular purpose. This product is protected by patent law, trademark law, copyright law, international treaties and/or other applicable law. All rights reserved. Unauthorized sale, manufacturing or use may result in civil and criminal penalties.


Standox® Low VOC Etching Adhesion Primer

Ordering Information: 1 Liter Low VOC Etching Adhesion Primer 020 16189

1 Liter Low VOC Etching Adhesion Activator 020 16190

Features: 2K Low VOC Acid Primer Excellent adhesion Chromate free Outstanding corrosion protection


Substrates: Through-hardened, sanded paintwork Bare metal- aluminum-galvanized metal, sanded and thoroughly cleaned Standox Polyesters, sanded (for adhesion in case of sand-throughs)

Sand and clean repair area thoroughly. For sensitive substrates, carry out a solvent test.


2:1 with Low VOC Etching Adhesion Activator potlife 8 h /68°F (20°C)

Ready to spray

1.3 - 1.4 mm 1.5-2 coats = 0.32 mil (8 micron) Please refer to gun manufacturer and local legislation for proper spray pressure recommendations.

1.2 - 1.3 mm 1.5-2 coats = 0.32 mil (8 micron) Please refer to gun manufacturer and local legislation for proper spray pressure recommendations.

25 min/ 68°F (20°C)

Standox VOC Complaint Fillers

313

Approved

Transfer Efficiency


Standox® Low VOC Etching Adhesion Primer


Low VOC Etching Adhesion Primer must be applied in combination with Standox PF Filler or Standox PF Sealer.

Do not overcoat with Polyester, Epoxy, Standox basecoat, or Standoblue® products.

For aluminum substrates, use only freshly mixed material. After sanding and cleaning the aluminum, prime immediately to prevent oxidation and adhesion failure.

Overcoat Standox Low VOC Etching Adhesion Primer with Standox PF Filler or Standox PF Sealer within 72 hours. After 72 hours without sanding, re-apply one coat of Standox Low VOC Etching Adhesion Primer and overcoat with Standox PF Filler or Standox PF Sealer.

Facilities enrolled in the Warranty program must use Standox PF Filler or Standox PF Sealer over Standox Low

VOC Etching Adhesion Primer for Warranty repairs.

Do not add thinners.



VOC Category


Density g/l



Pretreatment Coating 647 g/l – 282 g/l 929 g/l 85.1 %, 1.2%, 53.5%

56.4 %

Contains acid. May cause eye burns.




Approved

Transfer Efficiency

Standox® 1K Primer Filler

Ordering Information: 3.5 Liter 1K Primer Filler 020 16134

0.5 Liter 1K Primer Filler Aerosol 020 16228

Features:

1K Acid Primer Chromate free Corrosion protection Suitable as a weld-through primer


Substrates: Bare metal-aluminum-galvanized metal, sanded and thoroughly cleaned Through-hardened 2K Filler, sanded Sanded, solvent resistant OEM primers used on replacement parts Standox polyester substrates, sanded (for adhesion in case of sand-throughs)


50% Standox 2K Thinners

18-20s / DIN 4mm/ 68°F (20°C)

1.3 - 1.4 mm 1 coat = 0.6 mil (15 micron) Please refer to gun manufacturer and local legislation for proper spray pressure recommendations.

1.2 - 1.3 mm 1 coat = 0.6 mil (15 micron) Please refer to gun manufacturer and local legislation for proper spray pressure recommendations

10-15 min / 68°F (20°C)

Standox 2K Fillers

413


Standox® 1K Primer Filler


Prior to Standoblue® Basecoat or Standox Basecoat, Standox 1K Primer Filler can be used on small sand-

throughs to bare metal. This procedure does not apply to the Standox Lifetime Warranty.

Do not overcoat with polyester or epoxy products.

Facilities enrolled in the Standox Warranty Program must use Standox 2K Filler over Standox 1K Primer Filler

for Warranty repairs.

For optimum corrosion protection, use Standox Etching Adhesion Primer or Standox Low VOC Etching Adhesion

Primer.

Suitable as a weld-through primer.



VOC Category


Density g/l



3.5 Liter-Pretreatment Coating 741 g/l / 738 g/l 1003 g/l 74%, 0.4%, &, 0.0%

0.4%

Aerosol Coatings Auto Body Primer

PWMIR = 1.11 VOC % = 51.5%

830 82.1%, 0.3%, 30.2%

31.6%

Contains acid. May cause eye burns.



2009 Edition Page 20 Copyright© 2009 DuPont. Standox®, Standoflex®, Standohyd® and Standocryl® are registered trademarks of E.I. du Pont de Nemours and


Standox® 2.1 Filler

Ordering Information: 3.5 Liter 2.1 Filler 020 11999 Features:

High solid 2K Filler with excellent filling properties Exceptionally fast, air-dry qualities and excellent sanding properties Outstanding vertical hold out Mix with Standox VOC Sealer Agent for a 2.8 lb/gal Sealer

Working Process: Sanding Filler / Isolator

Working Process: 2.8 lbs/gal Sealer (2.1 Filler with 30% VOC Sealer Agent

Substrates: Through-hardened, sanded paintwork Sanded, solvent resistant OEM primers used

on replacement parts Standox Polyester substrates, sanded GRP, sanded Standox Etching Adhesion Primer Standox 2K EP Primer Surfacer/ 2K EP Primer

Aerosol


on replacement parts Standox Polyester substrates, sanded GRP, sanded Standox Etching Adhesion Primer Standox 2K EP Primer Surfacer/ 2K EP

Primer Aerosol For substrate preparation information see Standox Painting System S1!


4:1 with Standox 2.1 Hardeners (Fast, Normal, Slow, Extra Slow) potlife 90 min/68°F (20°C) (Areas outside of California - use 2K Hardeners.)

2:1 with Standox 2.1 Hardeners (Fast, Normal, Slow, Extra Slow) potlife 60 min/68°F (20°C)

20-30% Standox 2.1 Thinners 18-23 s/DIN 4 mm/68°F (20°C) (Areas outside of California - use 2K Thinners.)

30% Standox VOC Sealer Agent (16171)

1.5 - 1.8 mm 2-4 coats = 3.0-7.0 mil (80-160 micron) Please refer to gun manufacturer and local legislation for proper spray pressure recommendations.

10-20% Standox 2.1 Thinners 14-16 s/DIN 4 mm/68°F (20°C) The amount of thinner depends on the application temperature and which hardener is used.

1.4 - 1.8 mm 2-4 coats = 3.0-7.0 mil (80-160 micron) Please refer to gun manufacturer and local legislation for proper spray pressure recommendations.

1.3 - 1.5 mm 1-1.5 coats = 1.0 mil (25 micron) Please refer to gun manufacturer and local legislation for proper spray pressure recommendations.

For 5 mil (127 micron) or less Air dry for 45 min/ 80°F (27°C) or 20-30 in 140°F (60°C) panel temperature

1.3 - 1.5 mm 1-1.5 coats = 1.0 mil (25 micron) Please refer to gun manufacturer and local legislation for proper spray pressure recommendations.

Short wave 10-12 min Medium wave 14-16 min (see Painting System S9)

Flash off hand slick 20 min to maximum 40 min/ 68°F (20°C)

Orbital sand P400-P500 Wet sand P600-P800

Standocryl 2K Paints or Standox Basecoat/ Standohyd Basecoat with Standocryl 2K VOC Compliant Topcoats

Standocryl 2K VOC Compliant Topcoats

545



2009 Edition Page 21 Copyright© 2009 DuPont. Standox®, Standoflex®, Standohyd® and Standocryl® are registered trademarks of E.I. du Pont de Nemours and


Standox® 2.1 Filler Important Technical Remarks: • For areas outside of the 2.1 lbs/gal limit, Standox 2.1 Filler can be mixed with Standox 2K Hardeners and 2K

Thinners. 4:1+20-30% 18-23s/DIN 4mm. The addition of 2K Thinners and 2K Plasticiser will slow the flash off times in warm weather conditions and on large areas.

• Standox 2K Fast Dry Additive (16169) can not be used in the product. • When using Standox 2.1 Filler in wet-on-wet application methods, the use of slower hardeners and slower

thinners significantly improves flow, leveling and risk of over application. • Higher film builds and lower temperatures will require longer drying times. • Small imperfections can be reworked with Standox Polyester Stopper. Spot polyester must be re-primed. • Unsanded replacement parts primed with solvent-resistant E-coat primer can be directly with this product after

thoroughly cleaned with Standox Silicone Remover Antistatic/ Standohyd VOC Cleaner 25 or Standohyd Cleaner and a scuff pad.

• Use a Standox Etch Primer on all bare metal for Warranty compliance and adhesion. • For areas of California with Specialty Coating % limitations, Standox 2.1 Filler can be used for plastic refinishing.

Raw plastic must be pre-primed with Standoflex® 1K Plastic Primer (12065). This filler should not be used on plastics such as ABS or polycarbonate.

Repairing Plastic Parts (See Plastics Pg 3.) 2.1 Filler 2K Plasticiser 2.1 Hardener VOC Sealer

Agent 2.1 Thinner

Wet-on-wet 2 Parts +15% :1 +30% +10% Sanding 2 Parts +30% :1 None +30% Important Legislative Remarks: • Please see the appropriate VOC Wallchart for compliance for your area. 2.1 Filler recommended as a wet-on-wet

sealer is not compliant for Air Quality Districts 1151 and 4612 as of January 1, 2009. The values depicted below are “as applied regulatory (highest possible combination)” for the coating. Values have been determined using EPA Test Method 24. Please see the Master Values List for information on individual components.

VOC Category

VOC Regulatory Density g/l



Primer (California) 2.1 lbs/gal - 249 g/l 1575 g/l 50% 45.0%

Primer (National Rule) 4.5 lbs/gal - 539 g/l 1471 g/l 49.6% 13.5%

Sealer (California) 2.2lbs/gal – 266g/l 1456 g/l 51.1% 61.8%

Elastomeric Primer (California) 2.0 lbs/gal - 240 g/l 1433 g/l 51.9% 43.0%

Elastomeric Primer (National Rule) 4.4 lbs/gal - 527 g/l 1213 g/l 51.0% 11.3%

• For industrial use only by professional, trained painters. Not for sale to or use by the general public. Before using, read and follow all label and MSDS precautions. If mixed with other components, mixture will have hazards of all components. Ready to use paint materials containing isocyanates can cause irritation of the respiratory organs and hypersensitive reactions. Asthma sufferers, those with allergies and anyone with a history of respiratory complaints must not be asked to work with products containing isocyanates. Do not sand, flame cut, braze or weld dry coating without a NIOSH approved air purifying respirator with particulate filters or appropriate ventilation, and gloves.



Standox® 2K HS System Filler

Ordering Information: 3.5 Liter 2K HS System Filler Light Gray 020 15161

3.5 Liter 2K HS System Filler Dark Gray 020 16170

Features:

Excellent vertical hold-out Chromate free Excellent filling properties

Working Process: 4:1 HS Priming System

Substrates: Through-hardened, sanded paintwork Sanded, solvent resistant OEM primers used on replacement parts TPA and critical substrates Standox Polyesters, sanded


4:1 with Standox 2K Hardeners

(05-15, 15-25, 20-30, 25-40, 30-45) potlife 60-90 min/68°F (20°C)

If necessary, add up to 10% Standox 2K Thinner.

24-26 s/DIN 4 mm/68°F (20°C)

1.5 - 1.8 mm 2–3 coats = up to 8.0 mil (200 micron) Flash 5-10 minutes between coats Please refer to gun manufacturer and local legislation for proper spray pressure recommendations.

1.4 - 1.8 mm 2–3 coats = up to 8.0 mil (200 micron) Flash 5-10 minutes between coats. Please refer to gun manufacturer and local legislation for proper spray pressure recommendations.

Air dry 3 hours @ 80°F (27°C) or Flash off 5-15 min/ 68°F (20°C), then Bake 30 min 140°F (60°C) panel temperature

Short wave 12-15 min Medium wave 18-22 min (see Painting System S9) For higher film builds overnight dry.


Standocryl® 2K Paints or

Standox Basecoat / Standoblue® Basecoat with Standocryl 2K Clears

Approved

Transfer Efficiency

548


Standox® 2K HS System Filler


Unsanded replacement parts primed with solvent-resistant E-coat primer can be directly coated with this product after thoroughly cleaning with Standox Silicone Remover Antistatic/Standohyd

® VOC Cleaner 25/Standohyd

Cleaner and a scuff pad.

Standox 2K Fast Dry Additive (16169) can not be used in this product.

For better control of the sanding process, spray the filler and allow to dry. Apply a guide coat before sanding.

Use a Standox Etch Primer on all bare metal for Warranty compliance and adhesion.

Apply a maximum of 2 coats (approx 3.0 mil) before sanding. Increase flash off times before baking. If plasticized, do not store on mixing bank. Mix only before use.

For plastic refinishing, best results are achieved when using Standox 2K Nonstop Primer Filler. When Standox 2K HS System Filler is used for plastic refinishing, mix with 30% Standox 2K Plasticiser (2+30%:1). Raw plastic must be pre-primed with Standoflex

® 1K Plastic Primer (14408/12065).

Repairing Plastic Parts (See Plastics Pg 3.)

2 +30% :1

2K HS System Filler 2K Plasticiser Hardener



VOC Category




Primer Surfacer 508 g/l / 506 g/l 1367 g/l 37.2%, 0.2%, 0% 0.3%

Elastomeric Coating 489 g/l / 488 g/l 1252 g/l 39.1%, 0.1%, 0% 0.2%

For industrial use only by professional, trained painters. Not for sale to or use by the general public. Before using, read and follow all label and MSDS precautions. If mixed with other components, mixture will have hazards of all components. Ready to use paint materials containing isocyanates can cause irritation of the respiratory organs and hypersensitive reactions. Asthma sufferers, those with allergies and anyone with a history of respiratory complaints must not be asked to work with products containing isocyanates. Do not sand, flame cut, braze or weld dry coating without a NIOSH approved air purifying respirator with particulate filters or appropriate ventilation, and gloves.



Standox® 2K Nonstop Primer Filler

Ordering Information: 3.5 Liter Medium Gray 020 15331

3.5 Liter Dark Gray 020 16153

3.5 Liter White 020 16154

Features:

Available in 3 colors Outstanding Isolating properties Wet-on-wet or sanding application

Working Process: 3:1 Adhesion Promoter

Working Process: Sanding Filler / Isolator

Substrates: Solvent resistant OEM primers used on

replacement parts Solvent test E-coat primers to determine suitability of this procedure.


on replacement parts Standox Primers

TPA and critical subtrates Standox Polyesters, sanded




(05-15, 15-25, 20-30, 25-40) potlife 30 min/68°F (20°C)


(05-15, 15-25, 20-30, 25-40, 30-45) potlife 30 min/68°F (20°C)

30% Standox 2K Thinner

14-16 s/DIN 4 mm/68°F (20°C)

15-20% Standox 2K Thinner

20-25 s/DIN 4 mm/68°F (20°C)

1.3 - 1.4 mm 1–1.5 coats = 0.8-1.2 mil (20-30 micron) Please refer to gun manufacturer and local legislation for proper spray pressure recommendations.

1.4 - 1.7 mm 2–3 coats = 2.4-3.6 mil (60-120 micron) Please refer to gun manufacturer and local legislation for proper spray pressure recommendations.

1.2 - 1.3 mm 1–1.5 coats = 0.8-1.2 mil (20-30 micron) Please refer to gun manufacturer and local legislation for proper spray pressure recommendations.

1.4 - 1.7 mm 2–3 coats = 2.4-3.6 mil (60-120 micron) Please refer to gun manufacturer and local legislation for proper spray pressure recommendations.

Flash off 15-20 min/68°F (20°C) *Before overcoating with Standoblue Basecoat,

flash off at least 20 minutes.

Flash off handslick 10-15 min/68°F (20°C) between coats.

Standocryl® 2K Paints or Standox Basecoat

/ Standoblue® Basecoat with Standocryl

®

2K Clears

Air dry overnight/68°F (20°C) or 30 min/140°F (60°C) panel temperature or 60 min/120°F (48°C) panel temperature for isolating procedures

P800 (recommended for isolation) P400-P500 Orbital sander

Standocryl 2K Paints or Standox Basecoat / Standoblue Basecoat with Standocryl

2K Clears

Approved

Transfer

Efficiency

Approved

Transfer

Efficiency

535


Standox® 2K Nonstop Primer Filler Important Technical Remarks:

Overcoat Standox 2K Nonstop Primer Filler within 45 minutes at 68°F (20°C) for maximum adhesion. After 45 minutes Standox 2K Nonstop Primer Filler must be sanded before overcoating.

Standox 2K Fast Dry Additive (16169) may not be used in this product.

When used as a wet-on-wet sealer, for best results apply 1 light coat followed immediately by a medium, wet coat.

Do not use infrared drying for TPA or critical substrates not resistant to solvents.

Unsanded replacement parts primed with solvent-resistant E-coat primer can be directly coated with this product after thoroughly cleaning with Standox Silicone Remover Antistatic/Standohyd

® VOC Cleaner 25 /Standohyd

Cleaner and a scuff pad.

OEM E-coat must be sealed or primed to meet the Standox Lifetime Warranty Program requirements.

Facilities enrolled in the Standox Lifetime Warranty Program are required to first use a Standox Etch Primer on

all bare metal.

When this product is used as a wet-on-wet sealer the mix ratio is 3:1+10% 2K Thinner+20% PF Thinner.

For plastic refinishing, mix with 15-30% Standox 2K Plasticiser. If plasticised, do not store on mixing bank. Mix

only before use.

OEM-Primed Replacement Bumpers (Wet-on-Wet) (See Plastics Pg 2.) Mixing Stick N or O.

3 +15% :1 +20%

2K Nonstop Primer Filler 2K Plasticiser Hardener 2K Thinner Repairing Plastic Parts (Sanding) (See Plastics Pg 3.) Mixing Stick L.

3 +30% :1 +10-15%

2K Nonstop Primer Filler 2K Plasticiser Hardener 2K Thinner



VOC Category




Primer Sealer 544g/l / 452 g/l 1370 g/l 49.4%, 0.1%, 16.2% 16.8%

Primer Surfacer 576g/l / 574 g/l 1335 g/l 43.2%, 0.1%, 0% 0.2%

Adhesion Promoter 589g/l / 587 g/l 1312 g/l 44.9%, 0.2%, 0% 0.2%

Elastomeric Coating (wet-on-wet) 550 g/l / 550 g/l 1309 g/l 42.2%, 0.1%, 0% 0.2%

Elastomeric Coating (sanding) 520 g/l / 519 g/l 1274 g/l 40.9%, 0.1%, 0% 0.2%


Any analytical results set forth herein do not constitute a warranty of specific product features or of the product’s suitabi lity for a specific purpose. All products are sold pursuant to our general conditions of sale. We hereby disclaim all warranties and representations, express or implied, with respect to this product, including any warranty of merchantability or fitness for a particular purpose. This product is protected by patent law, trademark law, copyright law, international treaties and/or other applicable law. All rights reserved. Unauthorized sale, manufacturing or use may result in civil and criminal penalties.


Standoflex® 1K Plastic Primer

Ordering Information: 1 Liter Standoflex

® 1K Plastic Primer Silver 020 12065

0.4 Liter Standoflex® 1K Plastic Primer Silver - Aerosol 020 14408

Features:

1K Primer for plastic painting Ready to spray Wet-on-wet over-coatable with Standox 2K Filler or Standox 2K Sealer

Working Process: Adhesion Promoter for Plastic Repair

Substrates: For a list of paintable plastic substrates, see Page 18.

Standox does not recommend the refinishing of any plastic that is identified as not paintable by the OEM supplier.


Apply 1 single, light coat = 0.04-0.08 mil

Flash off 30 min/68°F (20°C)

Standox 2K Fillers or Standox 2K Sealers. See specific product TDS for further

mixing and application information. Best results are achieved when using Standox 2K Nonstop Primer Filler.

720


Standoflex® 1K Plastic Primer Silver Important Technical Remarks:

Apply a single, light coat of Standoflex 1K Plastic Primer.

Shake or mix thoroughly before application.

Standox does not recommend the refinishing of any plastic that is identified as not paintable by the OEM

supplier.

Do not directly topcoat.



VOC Category

VOC Regulatory Density g/l Wt% Volatiles, Water & Exempts


Adhesion Promoter 1L 0.4L

838 g/l, 838 g/l 2.31 PWMIR

880 g/l 747 g/l

95.2%, 0%, 0% 98.0%, 0%, 0%

0%




Standoflex® 2K Plastic Primer Surfacer

Ordering Information:

1 Liter 2K Plastic Primer Surfacer 020 11816

1 Liter 2K Plastic Primer Surfacer - Black 020 16192

1 Liter 2K Plastic Hardener 020 11824

Features:

2K Primer for new, unprimed plastic parts Excellent adhesion Simple mixing ratio (1:1 with 2K Plastic Hardener) Wet-on-wet working process

Working Process: 2K Plastic Priming for new, unprimed plastic

Substrates: For a list of paintable plastic substrates, see page 18.

Standox does not recommend the refinishing of any plastic that is identified as not paintable by

the OEM supplier.


1:1 with Standoflex 2K Plastic Hardener (11824)

After mixing, material is ready to spray. 16-18 s/DIN 4 mm/ 68°F (20°C) Potlife 4 hours @ 68°F (20°C)

1.3 - 1.4 mm 2 coats = 1.2 mil (30 micron) (See Important Technical Remarks) Please refer to gun manufacturer and local legislation for proper spray pressure recommendations.

1.2- 1.3 mm 2 coats = 1.2 mil (30 micron) (See Important Technical Remarks) Please refer to gun manufacturer and local legislation for proper spray pressure recommendations.

Wet-on-wet application 15-20 min/68°F (20°C) 30 min when overcoating with Standoblue

® Basecoat

30 min/140°F (54°C) panel temperature or 2h/ 68°F (20°C) If necessary, denib with P600-P800.

Plasticised 2K Standocryl, Standox Basecoat, or Standoblue Basecoat with plasticised Standox 2K Clears

750

Approved Transfer

Efficiency


Standoflex® 2K Plastic Primer Surfacer Important Technical Remarks:

Do not over apply, especially the first coat.

Use only Standoflex 2K Plastic Hardener in this product. Do not add thinner.

Standoflex 2K Plastic Hardener must not be stored below 50°F (10°C)

Standox does not recommend the refinishing of any plastic that is identified as not paintable by the OEM

supplier.

If higher film build is desired for repairs, apply 1 coat of 1K Plastic Primer over bare plastic. Flash off 20 minutes. Follow with plasticised 2K Nonstop Primer Filler, 2K HS System Filler, PF Filler, or PF Sealer. (See TDS 720.)

It is very important to make sure that the Standoflex 2K Plastic Primer Surfacer has thorough flash-off. Do not

trap solvents.

Maximum time before topcoating is 8 hours at 68°F (20°C).

For minor imperfections, apply Standox Basecoat and then denib.

For best results apply 1 light coat followed by a closed coat to achieve coverage.



VOC Category VOC Regulatory & Actual

Density g/l



Adhesion Promoter 671 g/l - 671 g/l 1041 g/l 64.4%, 0%, 0% 0%



2009 Edition 1 Copyright© 2009 DuPont. Standox®, Standoflex®, Standohyd® and Standocryl® are registered trademarks of E.I. du Pont de Nemours and


Standoflex® 1K Plastic Primer Ordering Information: 1 Liter Standoflex® 1K Plastic Primer 020 16202 Features:

Transparent gray low VOC 1K Primer for bare plastic Ready to spray Wet-on-wet over-coatable with compliant plasticised sealer

Working Process: Adhesion Promoter for Plastic Repair

Substrates: For a list of paintable plastic substrates, see Page 18.

Standox does not recommend the refinishing of any plastic that is identified as not paintable by the OEM supplier.


Shake well before use. Apply 1 single, light coat = 0.4-0.8 mil Do not apply to achieve hiding.

Flash off 30 min/68°F (20°C)

Overcoat with Standox VOC Compliant plasticised sealer with in 48 hours. Do not directly topcoat.

MIXING STICK “G” or “K”

2 +30% :1 +10-15% 2.1 Filler 2K Plasticiser Hardener 2K Thinner

Apply a maximum of 2 coats (approx. 3 mil) before sanding. Or If 2.1 Filler is used as a sealer, mix ratio is:

2 +15% :1 +30% +10-15% 2.1 Filler 2K Plasticiser Hardener VOC Sealer 2.1

Thinner

9721

2009 Edition 1 Copyright© 2009 DuPont. Standox®, Standoflex®, Standohyd® and Standocryl® are registered trademarks of E.I. du Pont de Nemours and


Standoflex® 1K Plastic Primer Important Technical Remarks: • Apply a single, light coat of Standoflex 1K Plastic Primer. • Standox does not recommend the refinishing of any plastic that is identified as not paintable by the OEM

supplier. • Do not directly topcoat. • Standoflex 1K Plastic Primer may be re-coated at any stage of curing. Avoid multiple coats and excessive film

build. Important Legislative Remarks: • Please see the appropriate VOC Wallchart for compliance for your area. The values depicted below are “as

applied regulatory” for the coating. Values have been determined using EPA Test Method 24. Please see the Master Values List for information on individual components.

VOC Category Adhesion Promoter

VOC Regulatory 4.5 lbs/gal – 540 g/l

Density g/l



Standoflex 1K Plastic Primer (Adhesion Promoter) 1L

4.0 lbs/gal - 476 g/l 1124 g/l 77.9%, 0.2%, & 44.8%

38.3%

• For industrial use only by professional, trained painters. Not for sale to or use by the general public. Before using, read and follow all label and MSDS precautions. If mixed with other components, mixture will have hazards of all components. Do not sand, flame cut, braze or weld dry coating without a NIOSH approved air purifying respirator with particulate filters or appropriate ventilation, and gloves.



Standox® EP Primer Surfacer

Ordering Information: 1 Liter EP Primer Surfacer 020 16183

1 Liter EP Hardener 020 16184

Features:

Epoxy-based universal primer surfacer Outstanding isolating properties Good weather-resistant properties

Working Process: 3:1 Sanding Filler

Substrates: Through-hardened, sanded paintwork Bare metal, sanded Galvanised metal, sanded Aluminum, sanded Standox Polyester substrates, sanded


3:1 with Standox EP Hardener

potlife 3 hours/68°F (20°C)

25% Standox 2K Thinners

17-19 s/DIN 4 mm/68°F (20°C)

1.3 - 1.5 mm 2-3 coats = 2-4 mil (60-110 micron) Please refer to gun manufacturer and local legislation for proper spray pressure recommendations.

1.3 - 1.5 mm 2-3 coats = 2-4 mil (60-110 micron) Please refer to gun manufacturer and local legislation for proper spray pressure recommendations.

Air dry overnight/68°F (20°C) or 30-40 min/140°F (60°C) panel temperature

Short wave 12-14 min


Standocryl® 2K Paints or

Standox Basecoat or Standoblue® Basecoat with Standocryl

®

2K Clears

931.1



Standox® EP Primer Surfacer Important Technical Remarks:

May be used as an isolator for solvent sensitive finishes.

Not suitable as a wet on wet primer.

Do not apply Standox EP Primer Surfacer on acid etch primers.

For restoration work: EP Primer Surfacer will provide corrosion protection for up to 3 months when a film thickness of 2.0 mil is achieved.

Standox PE Spray Filler may be applied after Standox 2K EP Primer Surfacer is dry, sanded.



VOC Category




Primer 578 g/l - 578 g/l 1352 g/l 42.8 %, 0 %, & 0% 0%




Standox® Basecoat

Ordering Information: Please see the price list for ordering information

Features:

Standox MSB System Excellent color accuracy Easy to blend Excellent coverage

Working Process: MSB System

Working Process: Blending-in/ Droplet

Technique Substrates:

Through-hardened, sanded paintwork Standox 1K/2K Fillers Standox 2K Sealers Standohyd

® Primer Surfacer

Substrates: Repair area: Standox Fillers

Original paintwork: Sanded with P800-P1000 for Basecoat

Sand the area for application of basecoat with P800-P1000. Prep the rest of the panel with P1200-P1500 and finish with a gold scuff pad used with Standohyd Sanding Paste (020 14670).

Trizact P1000 may also be used.



50% Standox MSB Thinner

(See important remarks regarding VOC compliance.) 20-25 s/DIN 4 mm/68°F (20°C)

If necessary, spray 1-2 coats of Standox

Basecoat Colorless onto the entire area.

1.3 - 1.4 mm 2 coats = 0.6-1.0 mil (15-25 micron) Please refer to gun manufacturer and local legislation for proper spray pressure recommendations.

Apply 2 coats of Standox Basecoat to cover

the repair area, taper each coat.

1.2 - 1.3 mm 2 coats = 0.6-1.0 mil (15-25 micron) Please refer to gun manufacturer and local legislation for proper spray pressure recommendations.

Approx 10 min/ 68°F (20°C)

Flash off 5-10 min/ 68°F (20°C) Flash off hand slick between coats

Final blend and droplet coat- thin the ready to spray basecoat again approx. 30%

17s/ DIN 4mm@ 68°F (20°C) or mix ready-to-spray Basecoat 2:1 with Standox Basecoat

Colorless.

10-15 min /68°F (20°C) Final flash off

Finely spray border area with 15-25 psi using Droplet technique

Standocryl 2K Clears


610

Approved Transfer

Efficiency


Standox® Basecoat


For OEM Approvals and for film thickness above 1.6 mil (40 micron) (multi-stage systems), mix with 15% Standox 2K Hardeners. Thin 30-40% with Standox MSB Thinners. Allow longer flash off times. Potlife 1 hr @

68°F (20°C).

Hardened Basecoat should be overcoated within 8 hours @ 68°F (20°C) for maximum adhesion.

Always perform a sprayout of the Basecoat with the Clearcoat to verify the color match prior to the application.

Verify BC/CC VOC Compliance before use. Refer to Standox VOC wallcharts and local legislation.

Standox Basecoat Deep Black (16151) and 2K Basecoat Real Black (14017) are ready mix colors that utilize

special pigments. These colors must be applied last when used in multi color paint schemes.

Standox Basecoat Colorless can be mixed with ready-to-spray Standox Basecoat.

Standox Basecoat should be overcoated within 24 hours @ 68°F (20°C) for optimum results and to minimize

surface contamination.



VOC Category




Basecoat 2-Stage 600 g/l limit

802 g/l – 802 g/l

908 g/l

88.4%, 0.1%, 0%

0.1%

Basecoat 3-Stage 630 g/l limit

802 g/l – 802 g/l

908 g/l

88.4%, 0.1%, 0%

0.1%

Hardened Basecoat (2K) 767 g/l – 767 g/l 917 g/l 83.7%, 0.1%, 0% 0.1%

Uniform Finish Blender (2:1 with Basecoat Colorless)

802 g/l – 802 g/l

896 g/l

85.9%, 0.1%, 0%

0.1%




Standox® Basecoat Colorless

Ordering Information: 2.5 Liter Basecoat Colorless 020 16150

Features:

Ready to spray Provides easy blending of basecoat

Working Process: Uniform Finish Blender -Blending-in with Basecoat Substrates:

Prepare new panels as usual, see painting System S1.

Sand the repair area for application of Standox Basecoat with P800. Sand

surrounding blend areas with P1200-P1500 (wet or dry). Then, finish the entire surface with a gold scuff pad in conjunction with Standohyd

® Sanding Paste

(14670). Trizact P1000 may also be used. For substrate preparation information see Standox Painting System S1!

Spray 1-2 coats of Standox Basecoat Colorless onto the entire area.

Dilute Standox Basecoat to 17s/DIN 4 mm or mix ready-to-spray Standox Basecoat 2:1 with Standox Basecoat Colorless. Reduce spray pressure to 15-25

psi (1-1.5 bar). Use the droplet technique, if necessary.

Lightly spray boundary area.

15-25 psi Droplet technique


613


Standox® Basecoat Colorless Important Technical Remarks:

Standox Basecoat Colorless can be mixed with read-to-spray Standox Basecoat.

Can be thinned up to 10% with MSB Thinner if slower flash off is desired.



VOC Category




Uniform Finish Blender 2:1 w/ Basecoat Blender

802 g/ l – 802 g/l 896 g/l 85.9%, 0.1%, 0% 0.1%





Standohyd® Basecoat Ordering Information: Please see the price list for ordering information. Features:

Waterborne basecoat Easy application and blending Excellent coverage and color accuracy Contains less than 10% organic solvent Working Process: Water-thinnable

basecoat Working Process: Spot repair

Substrates:

Through-hardened, sanded paintwork Standox® 2K Fillers Standoflex® 2K Plastic Primer Surfacer Standox 2K Sealers

Substrates: For preparation of repair areas see painting

System S1. For blending operations, see painting System S7.


Sand adjacent panels non-primed areas with P1200 and the rest of the panel with a gold scuff pad used with Standohyd Sanding Paste. Trizact P1000 may be used. For substrate preparation information see Standox Painting System S1!

5% Standohyd Special Additive may be used in all colors but is only required in the ground coats of 3-Stage colors.

5% Standohyd Special Additive may be used in all colors but is only required in the ground coats of 3-Stage colors.

Standohyd VE Water or Standohyd LH Thinner (Low Humidity) 20-26 s/DIN 4 mm/68°F (20°C) Viscosity depends on painting temperature and humidity. Lower in low humidity (20-23s), higher in high humidity (24-26s).

Thin Standohyd Basecoat to 20-22s/ DIN 4 mm/ 68°F (20°C) and regulate spray pressure Conventional equipment: 40-50psi HVLP or ATE Equipment: 20-25psi Use guns designed specifically for water-based application.

Gravity feed designed for water application (SATA/ Devilbiss/ IWATA) 1.2 - 1.4 mm (10 psi at the air cap) 1.5 coats = 0.6-0.8 mil (15-20 micron) 1 light pass, 1 normal pass and 1 light/ control pass= 1.5 coats (depending on color- Some colors may need further passes. If more coats are needed, allow further flash time before applying next coat).

Apply to the repair area and overlap each spray pass. For the final blend, use the droplet technique (low pressure), if necessary.

1.2 - 1.3 mm designed for water application 1.5 coats = 0.6-0.8 mil (15-20 micron) 1 light pass, 1 normal pass and 1 light/ control pass= 1.5 coats (depending on color- Some colors may need further passes with additional flash time.)

Flash off until matt. Flash off time will be reduced by at least 50% if using air jet.

Final flash off until completely matt. Flash off times can be reduced by the use or air jets, spray booth systems or infrared drying.

Apply Standocryl 2K Clears to entire repair area.

Oven dry 5-10 min/ 140°F (60°C) 5 min cooling


801

Approved Transfer

Efficiency



Standohyd® Basecoat Important Technical Remarks: • Mix 10% with Standohyd under hood colors. For best appearance and chemical resistance topcoat with matted/

low glass clearcoat. • Standohyd Basecoat must be overcoated with a 2K Standocryl Clear Coat for long term protection. • Standohyd Basecoat should be overcoated within 8 hours @ 68°F (20°C) for optimum results and to minimize

surface contamination. • Dispose of cleaning water properly. Do not dispose of cleaning water into drains. • Use standard health and safety equipment. • Use appropriate spray equipment designed for waterborne products. • Use only Standohyd VE Water or Standohyd LH Thinner (Low Humidity) for thinning to ensure proper product

performance. • When applying Standohyd Basecoat over 2K Nonstop Primer Filler and 2K Plastic Primer Surfacer wet-on-wet,

the 2K Fillers must flash-off for at least 20 minutes. • Do not add Standox Hardeners to Standohyd Basecoat. • For hot and low humidity conditions, viscosity should be 20s/DIN 4mm 68°F (20°C) and use a larger fluid tip. • For multi-stage ground coats and poor hiding colors, add 5% Standohyd Special Additive (16197) then thin with

VE Water to 20-22S/ DIN4. Verify color match before applying. Important Legislative Remarks: • Please see the appropriate VOC Wallchart for compliance for your area. The wallchart will reflect appropriate

VOC for BC/CC methodology. The values depicted below are “as applied regulatory” for the coating alone. Values have been determined using EPA Test Method 24. Please see the Master Values List for information on individual components.

VOC Category


Wt% Volatiles, Water, & Exempts


Standohyd Basecoat 3.5 lbs/gal - 419 g/l 1019 g/l 85.3% 75.6%

Standohyd Basecoat w/ LH Thinner

3.5 lbs/gal – 414 g/l 1020 g/l 79.6%, 67.5%, & 0.14%

68.7%

Standohyd Basecoat w/ Special Additive

3.3 lbs/gal – 401 g/l 1021 g/l 78.6%, 65.2%, & 0.0%

63.6%

• For industrial use only by professional, trained painters. Not for sale to or use by the general public. Before using, read and follow all label and MSDS precautions. If mixed with other components, mixture will have hazards of all components. Do not sand, flame cut, braze or weld dry coating without a NIOSH approved air purifying respirator with particulate filters or appropriate ventilation, and gloves.




Standocryl® 2.1 Clear Ordering Information: 5 Liter 2.1 Clear 020 10020 Features:

2.1 Clear for VOC compliant paint systems in California Production repair clear

Working Process: 2:1 Mixing Ratio Clear Substrates:

Standox Basecoats Standohyd Basecoats Through-hardened, sanded paintwork


2:1 with Standox 2.1 Hardeners (Fast, Normal, Slow, Extra Slow) potlife 4-6 hours /68°F (20°C)

Approx. 5-10% Standox 2.1 Thinners (Fast, Normal, Slow) 15-16 s/DIN 4 mm/ 68°F (20°C)

1.3 - 1.4 mm 1.5 coats = 2.0-2.4 mil (50-60 micron) Please refer to gun manufacturer and local legislation for proper spray pressure recommendations. Note: 1.5 coat process= one continuous application to achieve between 2.0- 2.4 mil.


Flash off 5-10 min/68°F (20°C)

Bake 20 min/130°F (55°C) panel temperature or Air dry 8 hours to overnight/ 68°F (20°C)

577

Approved Transfer

Efficiency



Standocryl® 2.1 Clear Important Technical Remarks: • Standox 2K Plasticiser may be added 15% with Standox 2.1 Clear. Mix ratio is:

2.1 Clear Plasticised Mixing Stick F or J. 2 +15% :1

2.1 Clear 2K Plasticiser Hardener Thin to spray viscosity. Flash off and drying times will be longer. Up to 30% Standox 2K Plasticiser may be added for extremely flexible parts. • Standocryl 2.1 Clear can be matted by mixing with Standocryl 2K Matt Clear 007. See TDS 570 in the Plastics

Section of this manual. • This clear may also be used in a 2-coat process. Allow 10 minutes flash between coats. • In VOC Topcoat limits of 4.5 lbs/gal, Standox 2K Thinners may be used. Important Legislative Remarks: • Please see the appropriate VOC Wallchart for compliance for your area. The wallchart will reflect appropriate

VOC for BC/CC methodology. The values depicted below are “as applied regulatory” for the coating alone. Values have been determined using EPA Test Method 24. Please see the Master Values List for information on individual components.

VOC Category




Topcoat Clear Coat (420 g/l limit) 2:1+10%

2.1 lbs/gal - 249g/l

1118 g/l

56.1%, 0.0%, 41.6%

37.5%


2.9 lbs/gal - 345 g/l

1095 g/l

55.7%, 0.0%, 33.3%

29.6%

Elastomeric Clear Coat (420 g/l limit) 2:1+10%

2.1 lbs/gal - 246 g/l

1123 g/l

54.0%, 0.0%, 39.2%

35.3%


2.9 lbs/gal - 343 g/l

1096 g/l

53.5%, 0.0%, 30.8%

27.3%

Elastomeric Matt Coating 4.4 lbs/gal - 529 g/l 1046 g/l 57.4%, 0.0%, 11.5%

9.2%

• For industrial use only by professional, trained painters. Not for sale to or use by the general public. Before using, read and follow all label and MSDS precautions. If mixed with other components, mixture will have hazards of all components. Ready to use paint materials containing isocyanates can cause irritation of the respiratory organs and hypersensitive reactions. Asthma sufferers, those with allergies and anyone with a history of respiratory complaints must not be asked to work with products containing isocyanates. Do not sand, flame cut, braze or weld dry coating without a NIOSH approved air purifying respirator with particulate filters or appropriate ventilation, and gloves.



Standocryl® 2.1 HS Clear


5 Liter 2.1 HS Clear 020 16156

Features:

High Quality 2.1 Clear for VOC compliant paint systems in California Excellent mechanical and chemical resistance Outstanding vertical hold out

Working Process: 2:1 Mixing Ratio Clear

Substrates: Standox

® Basecoats

Standoblue® Basecoats



2:1 with Standox 2.1 Hardeners

(Fast, Normal, Slow, Extra Slow) potlife 4-6 hours /68°F (20°C)

Approx. 5-10% Standox 2.1 Thinners

(Fast, Normal, Slow) 15-16 s/DIN 4 mm/ 68°F (20°C)




Bake 25 min/130°F (55°C) panel temperature or Air dry 8 hours to overnight/ 68°F (20°C)

578

Approved

Transfer

Efficiency


Standocryl® 2.1 HS Clear


Standox 2K Plasticiser may be added 15% with Standocryl 2.1 HS Clear. Mix ratio is:

2.1 HS Clear Plasticised

2 +15% :1

2.1 HS Clear 2K Plasticiser Hardener

Thin to spray viscosity. Flash off and drying times will be longer. Up to 30% 2K Plasticiser may be added for

extremely flexible parts.

Standocryl 2.1 HS Clear can be matted by mixing with Standocryl 2K Matting Agent Mix 608. See TDS 9595.

This clear may also be used in a 2-coat process. Allow a 10 minute flash between coats.

Clean after use with a high quality cleaning thinner.



VOC Category


Density g/l




1.9 lbs/gal - 230 g/l

1118 g/l

54.7%,

0%, 41.5%

35.3%


2.8 lbs/gal - 341g/l

1091 g/l

54.2%, 0.0%, 31.4%

27.3%


1.9 lbs/gal – 226 g/l

1120 g/l

52.8%, 0.0%, 37.6%

33.3%


2.8 lbs/gal – 337 g/l

1093 g/l

52.3%, 0.0%, 29.2%

25.2%

Elastomeric Matt Coating 4.4 lbs/gal - 528 g/l 1046 g/l 57.3%, 0.0%, 11.3%

9.0%




Standocryl® 2K HS Clear


5 Liter 2K HS Clear 020 14580

Features:

High quality 2K HS Clear Excellent mechanical and chemical resistance High solid, low VOC technology Outstanding vertical hold out

Working Process: HS Clear System (2:1 System)

Substrates: Through-hardened, sanded paintwork Standox Basecoat Standoblue

® Basecoat



potlife 30-60 min /68°F (20°C) Use of Fast Dry Additive will shorten potlife.

Add Standox 2K Thinners to spray viscosity.

(5% max thinner when used with 2K Hardener) 16-18 s/DIN 4 mm/ 68°F (20°C) (2 coat process) 18-20 s/ DIN 4 mm/ 68°F (20°C) (1.5 coat process) 5% Standox 2K Fast Dry Additive may be added instead of 2K Thinners to speed

up the flash-off and baking process. See appropriate VOC Wallchart for compliancy in your area.

1.3 - 1.4 mm 1.5-2 coats = 2.0-2.4 mil (50-60 micron) Please refer to gun manufacturer and local legislation for proper spray pressure recommendations. Note: 1.5 coat process= one continuous application to achieve between 2.0- 2.4 mil.

1.2 - 1.3 mm 1.5-2 coats = 2.0-2.4 mil (50-60 micron) Please refer to gun manufacturer and local legislation for proper spray pressure recommendations. Note: 1.5 coat process= one continuous application to achieve between 2.0- 2.4 mil.

5-10 min/68°F (20°C) Final flash off

Bake 30 min/140°F (60°C) panel temperature or Air dry overnight/ 68°F (20°C)

Short wave 8-12 min Medium wave 12-14 min (see Painting System S9)

564

Approved Transfer

Efficiency


Standocryl® 2K HS Clear


Fast hardeners, thinners and 2K Fast Dry Additive may raise viscosity and shorten pot life.

Standox 2.1 Hardeners must be used for compliancy in 4.5 lbs/gal topcoat and 5.2 lbs/gal tri-stage limitation

areas. Please refer to the appropriate VOC wallchart for mixing for your area.

Standox 2.1 Hardener Fast & Standox 2.1 Thinner Fast/ 2K Rapid Thinner may be used for jambing.

Standox 2K HS Clear can be matted by mixing with Standocryl 2K Matt Clear 007. See TDS 570.

Standox 2K HS Clear can be mixed 15% with Standox 2K Plasticiser (15260). Add Standox 2K/2.1 Thinner or Standox 2K Fast Dry Additive to achieve viscosity. Flash off and drying times will be longer. Up to 30% 2K

Plasticiser may be added to extremely flexible parts. Mix ratio is:

2K HS Clear Plasticised

2 +15% :1

2K HS Clear 2K Plasticiser Hardener



VOC Category


Density g/l



Topcoat Clear Coat 2K Hardener 2:1

2:1+5% 2:1+10%

450 g/l – 450 g/l 474 g/l – 474 g/l 495 g/l – 495 g/l

1019 g/l 1015 g/l 1011 g/l

44.2%,0%,0% 46.7%,0%,0% 48.9%,0%,0%

0.0% 0.0% 0.0%

Topcoat Clear Coat 2.1 Hardener 2:1

2:1+5% 2:1+10%

367 g/l – 320 g/l 398 g/l – 350 g/l 426 g/l – 376 g/l

1067 g/l 1063 g/l 1057 g/l

46.2%,0%,16.2% 48.4%,0%,15.5% 50.5%,0%,14.9%

12.8% 12.2% 11.6%

Elastomeric Clear Coat 2K Hardener 2:1+10%

482 g/l – 482 g/l 1017 g/l 47.4%, 0%, 0% 0%

Elastomeric Clear Coat 2.1 Hardener

411 g/l - 363 g/l 1063g/l 49%, 0%, 14.8% 11.7%




Standocryl® VOC Platinum Clear


5 Liter VOC Platinum Clear 020 16161

1 Liter VOC Platinum Hardener 020 16162

Features:

Special 2K Clear with reflow effect for improved abrasion properties Durable high gloss for 2 stage finishes Extremely high chemical and mechanical resistance Has dedicated VOC Platinum Hardener Approved clear for OEM Scratch Resistant Clear repairs

Working Process: 3:1 Mixing Ratio Clear

Substrates: Standox Basecoats Standoblue

® Basecoats

Through-hardened, sanded paint work


3:1 with Standox VOC Platinum Hardener

potlife 80-100 min /68°F (20°C)

Ready to spray 15-16 s/DIN 4 mm/ 68°F (20°C)

1.3 - 1.4 mm 2 coats = 2.0-2.2 mil (45-55 micron) Please refer to gun manufacturer and local legislation for proper spray pressure recommendations. Note: 1.5 coat process= one continuous application to achieve between 2.0- 2.4 mil.

1.2 - 1.3 mm 2 coats = 2.0-2.2 mil (45-55 micron) Please refer to gun manufacturer and local legislation for proper spray pressure recommendations. Note: 1.5 coat process= one continuous application to achieve between 2.0- 2.4 mil.


Bake 30-35 min/140-150°F (60-65°C) panel temperature

Short wave 10-15 min (See Standox painting System S9)

586

Approved

Transfer Efficiency


Standocryl® VOC Platinum Clear


For 4.5 lbs/gal Topcoat limitation areas, Standocryl VOC Platinum Clear can be mixed 2:1 with Standox 2.1 Hardeners and be used over Standox Basecoat for 2-stage finishes. When used with the

dedicated hardener, it is compliant for 2 & 3-stage finishes when used over Standoblue Basecoat..

For 3.5 lbs/gal Topcoat limitation areas and for over Standoblue Basecoat, Standocryl VOC Platinum Clear can be mixed 2:1 with Standox 2.1 Hardeners.

Do not plasticise Standocryl VOC Platinum Clear.

Approval Clear for Mercedes Benz, Nissan and BMW.

For polishing see System 8.1 in Charts & Systems.



VOC Category


Density g/l



Clear Coat 410 g/l – 410 g/l 1005 g/l 40.8%, 0%, 0% 0%




Standocryl® 2K Plastic Clear Satin Gloss


1 Liter 2K Plastic Clear Satin Gloss 020 12227

Features:

Special Satin Gloss, flexible 2K Clear for plastics High mechanical and chemical resistance Excellent for matching OEM cladding gloss level

Working Process: MS System

Substrates: Standox

® Basecoats





(05-15, 15-25, 20-30, 25-40, 30-45) Potlife 3 hours @ 68°F (20°C)

Thin to spray viscosity with Standox 2K Thinners (Approximately 10%) 18-20 s/DIN 4 mm/ 68°F (20°C)

1.3 - 1.4 mm 2 = 2.0-2.4 mil (50-60 micron) Please refer to gun manufacturer and local legislation for proper spray pressure recommendations.


5-10 min/68°F (20°C) Flash off between coats and final flash

Bake 45 min/140°F (60°C) panel temperature

569

Approved Transfer

Efficiency


Standocryl® 2K Plastic Clear Satin Gloss


Accelerated hardeners and thinners may raise viscosity and shorten pot life.

This product may also be mixed: o 3:1 with Standox 2.1 Hardeners. If necessary, thin with 2K Thinners to spray viscosity. 16 s/ DIN 4.

This product is pre-plasticized. Do not add 2K Plasticiser.

Clean after use with a high quality cleaning thinner.

Shake and stir before use. Do not use mix lid and place on mix machine.


Please see the appropriate VOC Wallchart for compliance for your area. The values depicted below are “ready to spray.”

VOC Category


Density g/l



Elastomeric Matt Clear Coat 2.1 2K

466 g/l – 421 g/l 555 g/l – 555 g/l

1077 g/l 1028 g/l

51.1%, 0%, 12%

54%, 0%, 0%

9.7% 0%




Standocryl® 2K Matt Clear 007


1 Liter 2K Matt Clear 007 020 16163*

Features:

Extremely matt 2K additive Can be mixed with 2K Clears or used alone For small areas and replacement parts Plasticised for plastic substrates

Working Process: Elastomeric matt clear - additive

Substrates: Standox

® Basecoats



To be used alone or mixed with Standox 2K Clears. See Matting table for

examples of mix ratios.


Potlife 4 hours @ 68°F (20°C)

25% Standox 2K Thinner

15-16 s/DIN 4 mm/ 68°F (20°C)





570

Approved

Transfer Efficiency


Standocryl® 2K Matt Clear 007

Matting Table

2K Clears ½ Pint 1 Pint 1 Quart Hardener Thinner

2K Clear 15-60 2K 15-60 Plus

25g Clear +225g Matt Clear 007



3:1w/ 2K Hardener

10-25% 2K

Thinners

2K Premium Clear




3:1w/ 2K Hardener

10-25% 2K

Thinners

2K HS Clear 20g Clear +230g Matt Clear 007



3:1w/ 2K or 2.1

Hardeners

10- 25% 2K

Thinners

2.1/ 2.1 HS Clear




3:1w/ 2.1 Hardeners

10-25% 2K or 2.1 Thinners

The degree of flatness or gloss can further be adjusted based on individual requirement.

Higher Gloss Level Lower Gloss Level

Faster Hardener Slower Hardener Faster Thinner Slower Thinner High Viscosity Low Viscosity

Hardener w/ higher solid content Hardener w/ lower solid content Higher dry film build Lower dry film build

Force Drying Air Drying


Always perform a sprayout to verify gloss level.

Standocryl 2K Matt Clear 007 is suitable to matt small areas or replacement panels.

Suitable for jambing and underhood application.

Do not add additional 2K Plasticiser. This product is pre-plasticised.



VOC Category


Density g/l



Elastomeric Matt Clear Coat 2K Hardeners

2.1 Hardeners

529 g/l

409 g/l

1046 g/l

1089 g/l

57.4%, 0.01%, 11.5% 52.8%, 0.01%, 22.0%

9.2%

17.9%




Standox® 2K Plasticiser

Ordering Information: 1 Liter 2K Plasticiser 020 15260

Features:

Universal plasticiser for all Topcoat systems Also suitable for Standox 2K Fillers High, long term elasticity

Working Process: Elastic Additive

Substrates: Standox Basecoats Standoblue

® Basecoats


Mix Standox 2K Clearcoat, Standox 2K Filler or Standox 2K Sealer with Standox 2K Plasticiser according to the appropriate TDS.


Do not store 2K Fillers which are plasticised. Only mix prior to use.

To optimize the sanding properties the Standox 2K Fillers should be dried 45 min/ 140°F (60°C) panel

temperature.

Do not use Standox 2K Plasticiser in Basecoat. If additional flex is needed, add 15% Hardener.

Pay close attention to proper flash off times before baking to avoid solvent popping.

Always add plasticiser before the addition of hardener.


Please see the appropriate VOC Wallchart for compliance for your area.



592


Standox® Smart Blend Plus

Ordering Information: 1 Liter Smart Blend Plus 020 16174

Features:

Thinner for blending-in with Standocryl® 2K Topcoats.

Working Process: Blending-in with Standocryl 2K Topcoats


Sand the fade-out blend area carefully with a fine, dual action sander and P3000/P4000 (3M, Trizact or Abralon) and a soft interface pad. 6 inch disk (150 mm, optional for small areas with 3 inch sand disk).

Spray repair area with Standocryl Clears.

For use with US National Rule Clears mix the ready to spray 2K Clear with up to 400% Smart Blend Plus (16174). For use with 2.1 HS Clear* (16156), PFC 20 (16211), or PFC 30 (16216); mix the

ready to spray 2K Clear with up to 50% Smart Blend Plus (16174) in VOC regulated areas.

Bake 30-35 minutes @ 140-150°F (60-65°C) panel temperature. If polishing the same day, follow by IR (short wave) for at least 15 minutes @ 100%. For use with PFC 20 (16211), bake 20 minutes @ 130°F (55°C) panel temperature. For use with PFC 30 (16216), bake 30 minutes @ 130°F (55°C) panel temperature.


Blending-in with 2K Clearcoats and 2K Standocryl is not an approved OEM repair, nor is it covered under the Standox Lifetime Warranty. All warranty repairs require that clearcoat be applied to a suitable break line, i.e., edge to edge.



VOC Category


Density g/l



Uniform Finish Coating 540 g/l Uniform Finish Coating

4.5 lbs/gal - 534 g/l 3.3 lbs/gal - 401 g/l

1074 g/l 67.5%, 0.0%, & 29.5% 24.9%

Specialty Coating

6.8 lbs/gal - 812 g/l 6.8 lbs/gal - 810 g/l

938 g/l 86.5%, 0.0%, 0.2% 0.3%



1206


Standox® 2K Matting Agent Mix 608

Ordering Information: 1 Liter Standox

® 2K Matting Agent Mix 608 020 16199

Features:

Matting Agent for VOC regulated areas. Excellent for matching OEM cladding gloss levels. Versatile low gloss additive. Mixed with 2.1 HS and PFC 30 Clear to achieve various gloss levels.

Working Process: Reduced Gloss System for 2.1 HS Clear

Substrates: Standox

® Basecoats



Standox 2K Matting Agent MIX 608 must be mixed with Standox 2.1 HS Clear* before

addition of 2.1 Hardeners. See Matting table for examples of mix ratios.

2:1 with Standox 2.1 Hardeners

15-16s/ DIN 4 mm/ 68°F (20°C) Pot life 30-60 min.

5-10% 2.1 Thinners (Fast, Normal, Slow)





9595

Approved

Transfer Efficiency



Working Process: Reduced Gloss System for PFC 30

Substrates: Standox

® Basecoats



Standox 2K Matting Agent MIX 608 must be mixed with Standocryl Clear PFC 30 before the addition of Standox Hardeners (PFH 15-25, PFH 25-30, or PFH 30-35). See Matting

table for examples of mix ratios.

2:1 with Standox Hardeners (PFH 15-25, PFH 25-30, or PFH 30-35)

15-16s/ DIN 4 mm/ 68°F (20°C) Pot life 30-60 min.

20% PF Thinner



No intermediate flash required between coats 10-15 min/68°F (20°C) final flash

Bake 45 min/140°F (60°C) panel temperature


Shake well before mixing. This product is pre-plasticised. Do not add 2K Plasticiser.

Standox 2K Matting Agent MIX 608 may not be used alone.

Gloss levels may be adjusted by changing percentages of Standox 2.1 HS Clear* or Standocryl Clear PFC 30.

Add the matting agent according to the formula. Always perform a spray out to verify gloss level.

Can be used in underhood applications.

Apply with higher than normal gun distance with consistent 70-80% overlap.

For vehicles with matt OEM finishes or for large repairs, use Standox Hardener PFH 30-35.

Blending of the matt clear is not possible.

Do not store the MIX 608 on the mix machine.

Approved Transfer

Efficiency



Influencing Gloss Level Factors

Higher Gloss Level Lower Gloss Level Faster Hardener Slower Hardener Faster Thinner Slower Thinner High Viscosity Low Viscosity

Hardener w/ higher solid content Hardener w/ lower solid content Higher dry film build Lower dry film build

Force Drying Air Drying

Standox 2K Matting Agent Mix 608 with Standox 2.1 HS Clear (16156)

Flat (Cumulative Pint) Satin (Cumulative Pint)

Standox 2.1 HS Clear* 32.2 65.2 Standox 2K Matting Agent Mix 608 290.8 288.8

2.1 Hardener 433.8 432.5

2.1 Thinner 449.9 449.9 Standox 2K Matting Agent Mix 608 with Standocryl Clear PFC 30 (16216)

Flat (Cumulative Pint) Satin (Cumulative Pint)

Standocryl Clear PFC 30 42.0 49.0 Standox 2K Matting Agent Mix 608 283.0 283.5

PF Hardener 438.0 438.5

PF Thinner 543.5 544.0



VOC Category


Density g/l Wt% Volatiles, Water, & Exempts


Clear Coating Matt Standocryl

® 2.1 HS Clear

2.0 lbs/gal - 244 g/l 1.2 lbs/gal – 141 g/l

1081 g/l

50.3 % 0.3 %

13.0 %

12.4 %

Clear Coating Matt Standocryl

® Clear PFC 30

2.0 lbs/gal – 241 g/l 1.3 lbs/gal - 153 g/l

1148 g/l

52.2% 0.0%

41.9%

36.5%



Documents

1 NAFTA Refinishing Systems (English) · Standocryl® VOC Platinum Clear 16161 VOC Platinum Hardener None 3:1 3.6 (434) Standocryl ® 2K Premium Clear 16252 2K Hardener 2K Thinner