Upload
others
View
5
Download
0
Embed Size (px)
Citation preview
1. Introduction
Once you have soldered the headers your
board is ready to be placed into desired
mikroBUS™ socket. Make sure to align the
cut in the lower-right part of the board
with the markings on the silkscreen at the
mikroBUS™ socket. If all of the pins are
aligned correctly, push the board all
the way into the socket.
3. Plugging the board in
2 3
2. Soldering the headers
1
4. Essential features
Turn the board upward again. Make sure
to align the headers so that they are
perpendicular to the board, then solder the
pins carefully.
Turn the board upside down so that
bottom side is facing you upwards. Place
shorter parts of the header pins in both
soldering pad locations.
Before using your click board™, make sure
to solder 1x8 male headers to both left
and right side of the board. Two 1x8 male
headers are included with the board in
the package.
clickBOARDwww.mikroe.com
GPS2 click Manualver. 1.01
0 100000 023136
GPS2 Click™ is an accessory board in
mikroBUS™ form factor. It’s a compact and easy solution for adding GPS module to
your design. It features Quectel L30 GPS module as well as SMA antenna connector.
GPS2 Click™ communicates with target
board microcontroller via mikroBUS™
UART (Tx, Rx), I2C (SCL, SDA), SPI (MISO,
MOSI, SCK, CS), PWM, INT, AN and RST
lines. The board is designed to use 3.3V
and 5V power supply. LED diode (GREEN)
indicates the presence of power supply.
GPS2 click
GPS2 Click™ with it’s Quectel L30 IC is a compact solution for adding Global Positioning
Systems (GPS) to your design. The Quectel L30 has advanced jamming suppression mechanism and innovative RF architecture
ensuring maximum GPS performance. The
module supports location, navigation and
industrial applications including autonomous
GPS C/A, SBAS (WAAS or EGNOS) and A-GPS.
The board is designed for use with active
antennas.
8. Support
MikroElektronika off ers Free Tech Support (www.mikroe.com/esupport) until the end of product lifetime, so if something goes
wrong, we are ready and willing to help!
7. Code Examples
.com
Once you have done all the necessary
preparations, it’s time to get your click
board up and running. We have provided
the examples for mikroC, mikroBasic and
mikroPascal compilers on our Libstock website. Just download them and you are
ready to start.
.com
5. GPS2 Click™ Board Schematic
+3V3
E210
uF
CS
C4
100n
F
RST#
CN1ANTENNA
RXTX
ON/OFF
R8
1K
Q2BC846
WUPINT
12345678 9
10111213141516A1
VCCAA2A3A4A5A6OE
B5B6
B1VCCB
B2B3B4
GND
TXB0
106
U2
TXB0106
Vgps
+5V
R142K2
LD1PWR
J1
+5V
+3V3VCC
R12100K
Vgps
VCC
R15
1K
Q3BC846
R17100K
R1010K
Vgps
R2
1K
Q1BC846
R3100K
LD2
VCC
R13K3
SCKCS
RST#
PIN5
C1100nF
ANRSTCSSCK
MOSIMISO
+3.3VGND
PWMINT
RXTX
SCLSDA+5VGND
123456
7 8 9 10
111213141516
1718192021
GND EINT0
GND
RSTCFG0/SCKCFG1/SCSSCLSDA
1PPS
VIO
VCC
GN
D
CLKDIO
ON/OFFWAKEUP
RFI
N
GN
DG
ND
GN
DG
ND
U1QUECTEL L30
T_WUPT_RST#T_INT
T_ON/OFF
1PPS
1PPS
Vgps
VIO
R2010K
INT
WUP
R510K
Vgps
T_PIN3T_PIN4T_PIN5T_PIN6
SCK
R910K
R710K
VCC
PIN5
PIN6
PIN6
R112K2
R62K2
TX
RX
SCLSDA
MISOMOSI
C3100nF
Vgps
ON/OFF
SCL
SDA
MISO
MOSI
VCC
C22.2uF
R1622K
R13120K
R1812K1
Vgps
1
2
3
IN
GND
OUT 5
4EN ADJ
U3
AP7331-ADJ
J6
J3J2 J4
J5 J7
J8 J9
T_PIN3PIN5
PIN6
PIN6
PIN5
T_PIN4
J10 J11
T_PIN4
T_PIN3
R410K
T_CS
T_SCK
T_WUP
T_INT
T_ON/OFF
T_RST#T_SCKT_CST_PIN5T_PIN6
C522nF
R19
10
L1
47nH
+3V3
C64.7uF
C74.7uF
Vgps
C81uF
Vgps
C9
4.7uF
MIKROBUS DEVICE CONN.
MikroElektronika assumes no responsibility or liability for any errors or inaccuracies that may appear in the present document. Specifi cation and information contained in the present schematic are subject to change at any time without notice. Copyright © 2012 MikroElektronika. All rights reserved.
6. SMD Jumpers
There are three groups of jumpers: UART
(J2,J3,J4), I2C (J5,J6,J7) and SPI (J8,J9,J10,J11) By soldering zero-ohm SMD jumpers in
appropriate group, you will be able to change
communication between target board
microcontroller and Quectel L30 module. There is one SMD jumper J1 used to select between 3.3V or 5V power supply. J1 jumper is soldered in 3.3V position by default.