1. Available firmware, archives and documentation · 2018-05-08 · IC-NT V1.2.1 – New features / ©ComAp – December 2009 / IA-NT-1.2.1 New features.pdf p ComAp, spol. s r.o

New features of IC-NT sw V1.2.1 Page 1 of 13

IC-NT V1.2.1 – New features / ©ComAp – December 2009 / IA-NT-1.2.1 New features.pdf

ComAp, spol. s r.o. Kundratka 2359/17 180 00 Prague 8 Czech Republic

ISO 9001 Certified

ComAp s.r.o.

Quality Management

Tel.: +420 246 012 111 Fax: +420 246 316 647 E-mail: [email protected]

Internet: http://www.comap.cz

1. Available firmware, archives and documentation

Firmware Mhx file IC-NT-MINT-1.2.1.mhx IC-NT-SPtM-1.2.1.mhx

Archives Archives IC-NT-MINT-1.2.aic IC-NT-MINT-MultiKit-1.2.aic IC-NT-SPtM-1.2.aic IC-NT-SPtM-StarterKit-1.2.aic

Documentation PDF files Description InteliCompact-NT-1.2-Reference Guide.pdf Manual for InteliCompactNT controller InteliCompact-NT-1.2-Operator Guide.pdf Operator Guide for InteliCompactNT controller InteliCompact-NT-1.2.1 New features.pdf List of new features for software update version 1.2.1

2. Main changes in IC-NT-1.2.1

Repairs

• Issue with unintentional Stop Fail alarms appearing in MINT fixed While running in parallel (MINT) Stop Fail alarms appeared at the moment when one genset closed it's GCB to the bus. Other controllers sometimes issued Stop fail alarm although the engines were still. The issue has been fixed.

3. Main changes in IC-NT-1.2

Repairs

• Iveco Nef & Cursor / ECU Running Hours reading problem fixed Problem with ECU Running Hours reading for Iveco Nef & Cursor engines has been fixed.

• ScaniaS6AuxII / ECU DLN1 frame not sending problem fixed Problem with ECU DLN1 frame not sending for ScaniaS6AuxII engine has been fixed.

• John Deere / ECU TSC1 wrong frame contents fixed Problem with ECU TSC1 wrong frame contents for John Deere engine has been fixed.

New features

• Webserver for IB-Lite supported New secured way of monitoring and controlling the genset from any point in world using your web browser! Clear overview and control of the state of engine, its settings and history. User friendly.

mailto:[email protected]

http://www.comap.cz




ISO 9001 Certified

ComAp s.r.o.

Quality Management



Scada window:

Measurement window:


http://www.comap.cz




ISO 9001 Certified

ComAp s.r.o.

Quality Management



Setpoints window:

History window:

HINT: This feature requires IB-Lite optional plug-in module and visible connection of controller to ethernet.


http://www.comap.cz




ISO 9001 Certified

ComAp s.r.o.

Quality Management



• IL-NT BIO8 Hybrid binary input/output module available IL-NT BIO8 is optional plug-in card. Through this card controller can accommodate up to 8 binary inputs or outputs. In LiteEdit PC configuration tool (version 4.4 and higher) it is possible to easily choose if particular I/O will be binary input or output. To insert the module, you must open the cover first (use screwdriver to open) and then insert the module into slot. Once you have inserted it, the module will snap under plastic teeth. It is supposed to be installed permanently. Should you need to remove it, the safest way is to remove whole back cover and than remove module manually. Installing IL-NT BIO8 module is similar to installing RS 232 module. The difference is that module fits to “extension module” slot and after installing IL-NT BIO8 you do not put back the small cover.

Technical details: IL-NT BIO8 plugs into IC-NT controller EXTENSION MODULE port. 8 dedicated pins of the plug-in card’s terminal can be configured as binary inputs or outputs.

Binary inputs Number of inputs 8 Input resistance 4.7 kΩ Input range 0-36 VDC Voltage level for close contact indication (Logical 1) < 0.8 VDC Voltage level for open contact indication (Logical 0) > 2 VDC Max voltage level for open contact indication 8-36 VDC

Binary open collector outputs Number of outputs 8 Maximum current per pin 0.5 A Maximum switching common current 2 A Maximum switching voltage 36 VDC

HINT: Binary inputs are not galvanically isolated.


http://www.comap.cz




ISO 9001 Certified

ComAp s.r.o.

Quality Management




http://www.comap.cz




ISO 9001 Certified

ComAp s.r.o.

Quality Management



• IC-NT CT-BIO7 Hybrid current input & binary input/output module available (SPtM) IC-NT CT-BIO7 is optional plug-in card. Through this card controller can accommodate one AC current (CT) measuring input and up to 7 binary inputs or outputs. In LiteEdit PC configuration tool (version 4.4 and higher) it is possible to easily choose if particular I/O will be binary input or output. NOTE: Current measuring input is intended to measure one phase (AC) current of mains and to limit Export to mains to zero value during parallel to mains operation. This is case of SPtM application, so current input of IC-NT CT-BIO7 module is useful for SPtM controllers only.

To insert the module, you must open the cover first (use screwdriver to open) and then insert the module into slot. Once you have inserted it, the module will snap under plastic teeth. It is supposed to be installed permanently. Should you need to remove it, the safest way is to remove whole back cover and than remove module manually. Installing IC-NT CT-BIO7 module is similar to installing RS 232 module. The difference is that module fits to “extension module” slot and after installing IC-NT CT-BIO7 you do not put back the small cover.

Technical details: IC-NT CT-BIO7 plugs into IC-NT controller EXTENSION MODULE port. 7 dedicated pins of the plug-in card’s terminal can be configured as binary inputs or outputs.

Current measuring input Number of inputs 1 Nominal input current (from CT) 5 A Load (CT output impedance) < 0.1 Max measured current from CT 10 A Current measurement tolerance 2% from Nominal current Max peak current from CT 150 A / 1s Max continuous current 10 A (All values in RMS)

Binary inputs Number of inputs 7 Input resistance 4.7 kΩ Input range 0-36 VDC Voltage level for close contact indication (Logical 1) < 0.8 VDC Voltage level for open contact indication (Logical 0) > 2 VDC Max voltage level for open contact indication 8-36 VDC


http://www.comap.cz




ISO 9001 Certified

ComAp s.r.o.

Quality Management



Binary open collector outputs Number of outputs 7 Maximum current per pin 0.5 A Maximum switching common current 2 A Maximum switching voltage 36 VDC

NOTE: Binary inputs are not galvanically isolated.


http://www.comap.cz




ISO 9001 Certified

ComAp s.r.o.

Quality Management



• Object load dependent autostart function (peak shaving) added (SPtM) The gen-set can start and stop automatically according to the object load. An automatic start will occur if the object load exceeds the limit given by setpoint PeakLevelStart and remains exceeded for a period longer than PeakAutS/S Del. If the object load drops below PeakLevelStop, the gen-set will be stopped with the same delay as by start. The gen-set load is controlled according to selected mode.

NOTE: The gen-set will stay running if the binary input Rem Start/Stop is active.

PeakLevelStart [kW] Load consumption level the gen-set has to start at. Function is inactive when PeakAutS/Sdel = OFF. Genset start is PeakAutS/S Del delayed after the consumption of the Load exceeds the PeakLevelStart limit. Step: 0.1 kW / 1 kW* Range: PeakLevelStop to 3200.0 kW*

PeakLevelStop [kW] Load consumption level the gen-set has to stop at. Genset stop is PeakAutS/Sdel delayed after PeakLevelStop limit is reached. Load consumption is calculated (not directly measured) as a sum of gen-set and mains active power. Step: 0.1 kW / 1 kW* Range: 0 to PeakLevelStart kW*

*NOTE: The actual setpoint units and range depend on setting of the Power format (see Lite Edit manual).

PeakAutS/S Del [ s ] The condition for the "peak" automatic start or stop must be valid for time period longer than value of this setpoint to execute the automatic start or stop. Adjusting 0 causes stop of the gen-set (if there is no other demand for running) and disables the automatic start. Step: 1s Range: 0 (OFF) – 600 s

• Im CT Ratio setpoint added (SPtM) Im CT Ratio setpoint has been added to Basic Settings group. It defines mains current transformer ratio for current measuring input of IC-NT-CT-BIO7 extension module if used. Range: 1 .. 5000 [A/5A]

• Export Limit setpoint added (SPtM) Export Limit [DISABLED, ENABLED] setpoint has been added to Process Control group. It tells controller to activate protection against power export to the mains. The function limits gen-set requested power to hold import power higher or equal to the setpoint Export kW.

• Export kW setpoint added (SPtM) Export kW [-32000 kW .. 32000kW] setpoint has been added to Process Control group. It defines max limit for export in case Export Limit setpoint is set as ENABLED. Positive value means export limit, zero means no export.


http://www.comap.cz




ISO 9001 Certified

ComAp s.r.o.

Quality Management



• Synchro Enable setpoint added Synchro Enable [NONE / FORWARD / REVERSE / BOTH] setpoint has been added to Process Control group. It enables or disables forward/reverse synchronization (according to SPtM / MINT versions). NONE: No synchronizing is enabled. (SPtM & MINT) FORWARD: GCB synchronizing is enabled. (SPtM & MINT) REVERSE: MCB synchronizing is enabled. (SPtM) BOTH: GCB and MCB synchronizing are enabled. (SPtM)

• Fault Reset binary output added Logical binary output Fault Reset has been added. The output is a copy of Fault Reset button on controller and binary input FaultResButton.

• ECU values in history Following ECU values have been added to history record (using abbreviations listed in Abbreviation column):

Name Abbreviation

Oil pressure EOP

Coolant temperature ECT

Oil temperature EOT

Boost pressure EBP

Intake temperature EIT

Percent load at current speed EPL

Fuel rate EFR

• Binary outputs for speed/voltage control Following binary outputs for speed/voltage control have been added to controller:

Name Description

Speed Up

This output together with the complementary output Speed Down are designed for speed and power control at gen-sets, where the governor does not support analogue control. The outputs are also used for direct control of a gas throttle at asynchronous gen-sets.

Speed Down

This output together with the complementary output Speed Up are designed for speed and power control at gen-sets, where the governor does not support analogue control. The outputs are also used for direct control of a gas throttle at asynchronous gen-sets.

AVR Up This output together with the complementary output AVR Down are designed for voltage and power factor control at gen-sets, where the AVR does not support analogue control.

AVR Down This output together with the complementary output AVR Up are designed for voltage and power factor control at gen-sets, where the AVR does not support analogue control.

NOTE: Droop function is required when these outputs are used for power factor control.


http://www.comap.cz




ISO 9001 Certified

ComAp s.r.o.

Quality Management



• Setpoint AVR Character removed AVR Character setpoint has been removed from Volt/PF Ctrl group

• Decimal switching for power measurement added Possibility to select format for power measurement has been added. Format can be set via LiteEdit PC configuration tool version 4.4 and higher using its Units/Formats configuration dialog:

• New default values for parameters

Following parameters got new default values: ReversePwr BOC: 15% (old value 50%) AVRi Bias: 50% (old value 10%) Load Ramp: 30s (old value 5s) Sync timeout: 60s (old value 30s)

• Overall information about gen-sets running added to history (MINT only) Information about gen-sets with GCB closed and their overall P and Q has been added to history record (using abbreviations listed in Abbreviation column). Values can be also found in LiteEdit Values / Pwr Management and Info (LE ver. 4.4 and higher).

Value name Abbreviation Description

GensLoaded16 GL16 Each bit if set represents gent-set with its GCB closed

GensLoaded32 GL32 Each bit if set represents gent-set with its GCB closed

Running ActPwr TRPA Overall power from gen-set with its GCB closed

Running Q-Pwr TRQA Overall reactive power from gen-set with its GCB closed


http://www.comap.cz




ISO 9001 Certified

ComAp s.r.o.

Quality Management



• Customer Logo screen added Screen dedicated to information provided by customers such as contact numbers, service technician contact and customer message for end users of gen-set has been added. Configuration of this screen is only done by LiteEdit PC software (v. 4.4 and higher).

Information is displayed on so called “Init Screens” which are displayed after controller is switched on or reprogrammed. It is also possible to call these screens from any measurement screen by pressing ENTER and PAGE buttons concurrently and then only PAGE button separately.


http://www.comap.cz




ISO 9001 Certified

ComAp s.r.o.

Quality Management



• Timer1Function and Timer2Function setpoints added Timer1..2Function [No Func/TEST/TEST OnLd/MFail Blk/Mode OFF] setpoints have been added to Date/Time group. It is possible to choose out of 5 (3) following Timer functions. Binary output Timer is always activated when Timer is active regardless of chosen Timer function.

MINT: No Func: There is no any other function, but binary output ExercTimer1..2 activation. Mode OFF: When this option is chosen then the Timer output is also internally

connected to the Remote OFF binary input AutoRun: When this option is chosen then the Timer directly starts gen-set (in AUT

mode).

SPtM: No Func: There is no any other function, but binary output ExercTimer1..2 activation. TEST: When this option is chosen then the Timer output is also internally

connected to the Remote TEST binary input. TEST OnLd: When this option is chosen then the Timer output is also internally

connected to the Rem TEST OnLd binary input. MFail Blk When this option is chosen then the Timer output is also internally

connected to the MainsFailBlock binary input. Mode OFF: When this option is chosen then the Timer output is also internally

connected to the Remote OFF binary input

• Running Hours switching improved Running Hours switching between ECU and controller in case of ECU value is not valid has been improved.

• Logical binary input AMFFuncBlock renamed Logical binary input AMFFuncBlock has been renamed to MainsFailBlock

• Measuring core update Measuring core has been updated to support resistance measuring via analog input up to 15kOhm


http://www.comap.cz




ISO 9001 Certified

ComAp s.r.o.

Quality Management



4. Main changes in IC-NT-MINT-1.1.1

Repairs • Problem with Actual Reserve screen freezing whilst Chinese language used

Problem with freezing of Actual Reserve screen on controller running MINT application when Chinese language is selected has been fixed.


http://www.comap.cz

Documents

1. Available firmware, archives and documentation · 2018-05-08 · IC-NT V1.2.1 – New features / ©ComAp – December 2009 / IA-NT-1.2.1 New features.pdf p ComAp, spol. s r.o