8529-02 08710 - 1

SECTION 08710 – FINISH HARDWARE PART 1 – GENERAL 1.01 Related Documents

Drawings and general provisions of contract and Division 1 specification sections, apply to work of this section

1.02 SUMMARY This section DOES INCLUDE Aluminum door hardware as noted in sets. Work under this heading includes furnishing all hardware to respective trades. The hardware supplier shall promptly furnish templates to all manufacturers furnishing materials necessary for completion of this part. Extent of finish hardware is indicated on drawing and in schedules. The following specifications are a guide and a description of the quality materials required. No material of quality or weight less than outlined in this specification will be accepted. The contractor will be responsible for supplying the correct quantity of all materials, whether or not specifically mentioned in this specification. Any additional items that may be required shall be furnished and be of type, quality, and utility consistent with other hardware specified.

1.03 SUBMITTALS ARCHITECT’S HARDWARE SCHEDULE: Architect’s hardware schedule is by hardware set number. Refer to drawings for designation of hardware set number applicable to each opening. Certain additional items of hardware and/or hardware accessories specified herein shall be finished and noted on the hardware schedule.

Preferred Supplier for Hardware is: Baylor Commercial Door & Hardware, Inc. 101 23rd Street Ste 100 Corbin, KY 40701 Ph 606-528-5359 Fax 606-526-0649 E-mail: baylorcommercial@bellsouth.net

SUPPLIER’S HARDWARE SCHEDULE A complete hardware schedule, indicating type, number, location, and finish shall be submitted to architect for approval, together with such samples as may be required for review. Opening numbers shall be same as used in contract documents. Schedule shall be prepared according to Door and Hardware Institute recommendations (schedule and sequence format) and shall include degree of door closer installation. Supplier’s hardware schedule will be reviewed by architect for type, quality, finish, and for function (other than hand). Contractor shall be responsible for checking schedule for correct hand of locksets and for supplying quantity of items required by contract documents.

8529-02 08710 - 2

Provide supplementary or revised hardware schedules if deemed necessary by architect. Do not ship or deliver hardware to job prior to review of hardware schedules by architect. Hardware schedule shall be submitted in the following format. Hardware schedules submitted to architect for review not in this format will be rejected:

HARDWARE HEADING 1 1 Sgl Door #001 Exterior from Corridor RHR 90 deg

Each leaf 3’0 x 7’0 x HMF x NLWD

Item, quantity, manufacturer’s #, size, product type, finish, and product information 3 ea Hinge 5BB1NRP 4.5 x 4.5 630 IV 1 ea Cylinder 951 x GGMK 26D FA

1 ea Exit Device 25R L Dane x 3070 x RHR 32D FA Etc.

1.04 QUALITY ASSURANCE

All hardware shall be furnished by an established Builders Hardware firm who maintains and operates an office, display, and stock in this area, and who is a regular authorized distributor of the lock he proposes to furnish. All hardware schedules submitted for approval shall carry the signature and seal of a certified Architectural Hardware Consultant who is employed by the hardware firm supplying material.

1.05 PROJECT CONDITIONS

Delivery storage and handling: Hardware supplier shall receive and check all hardware at his warehouse. Drop shipments to the jobsite from various manufacturers will not be permitted. All hardware shall be in its original packaging and plainly labeled and numbered to agree with the numbers and as listed in the hardware schedule. The contractor shall submit his schedules for approval to the architect before proceeding with any work. When required, hardware supplier shall deliver hardware and/or hardware templates to the various door manufacturers. The general contractor shall provide storage facilities for the finish hardware after delivery to the job site.

1.06 ITEMS NOT INCLUDED

Hardware for metal windows, toilet partitions, cabinets, access panels, etc. is not included in this section. See other sections for hardware to be furnished by others. Reference Division 16 for electrical requirements.

8529-02 08710 - 3

PART 2 – PRODUCTS 2.01 MANUFACTURERS

Numbers given in this schedule are of the following manufacturers. PRODUCTS MFG. SPECIFIED APPROVED EQUAL Falcon Key cylinders and cores No Substitutions allowed Hinge Hager Ives, Bommer Locks Schlage Lock Sargent Exits Von Duprin Precision Closers LCN Sargent Trim/Auxiliary Hager Companies Rockwood, Ives Weather Strip Hager Pemko, NGP Custom Pulls Rockwood No Substitutions allowed

2.02 HARDWARE FINISHES The designations used to indicate hardware finishes are those listed in ANSI /BHMA A156.18, “Materials and Finishes”, including coordination with the traditional U.S. finishes, shown by certain manufacturers for their products.

1. Butt Hinges US26D (652) Satin

Chromium US32D (630) Satin Stainless Steel

2. Mortise Cylinders, Rim Cylinders, US26D (626) Satin

and “Permanent” Interchangeable Chromium Cores

3. Cylindrical Latch sets and Locksets US26D (626) Satin

Chromium 4. Exit Devices US26D (626) Satin

Chromium 5. Door Closers ALUM (689) Powder

Coated Aluminum

6. Overhead Door Stops US32D (630) Satin Stainless Steel

7. Flush Bolts and Dust Proof US26D (626) Satin

Strikes Chromium

8. Wall and Floor Stops US32D (626) Satin Stainless Steel

8529-02 08710 - 4

9. Door Coordinators US28 (628) Satin Aluminum, Clear Anodized

10. Door Pulls US32D (630) Satin Stainless Steel

11. Push Plates US32D (630) Satin

Stainless Steel

12. Mop, Kick, and Armor Plates US32D (630) Satin Stainless Steel

13. Saddle Thresholds 719 (US27) Mill Finish

Aluminum, Uncoated

14. Door Sweeps 628 (US28) Satin Aluminum, Clear Anodized

15. Self Adhesive Seals Clear (Silicone)

16. Perimeter Seals 628 (US28) Satin

Aluminum, Clear Anodized

17. Meeting Stile Seals 628 (US28) Satin Aluminum, Clear Anodized

18. Drip Strips 628 (US28) Satin

Aluminum, Clear Anodized

19. Door Silencers Gray Gray (Rubber) 2.03 HINGES

Characteristics: a. Tested to be in accordance with ANSI / BHMA A156.1. b. Templates: Provide only template-produced units. c. Fasteners: Provide Phillips flat-head screws complying with the following

requirements. (1) For metal doors and frames, install machine screws into

drilled and tapped holes. (2) For wood doors and frames, install threaded-to-the-head

wood screws. (3) For fire-rated wood doors, install #12 x 1-1/4 inch,

threaded-to-the-head steel wood screws. (4) Finish screw heads to match surface of hinges or pivots.

8529-02 08710 - 5

d. Hinge Pins: Except as otherwise indicated, provide hinge pins as follows: (1) Out-Swing Exterior Doors: Non-removable pins. (2) Out-Swing Interior Doors: Non-rising pins and Non-

removable pins; as indicated in the Door Hardware Sets. (3) In-Swing Exterior / Interior Doors: Non-rising pins. (4) Tips: Flat button and matching plug. Finished to match

hinge leaves. e. Size: Size hinges in accordance with the specified manufacturer’s published

recommendations. f. Quantity: Furnish one pair of hinges for all doors up to 5’-0” high.

Furnish one additional hinge for each additional 2-1/2 feet or fraction thereof.

2.04 CYLINDERS and KEYS Characteristics: a. Tested to be in accordance with ANSI / BHMA A156.28. b. “Exterior” Door Openings - Patented Key System: Except as otherwise

indicated, provide a NEW Key System for this Project. c. Equip all cylinders and locksets with, a minimum of, 7-pin interchangeable

core, tumbler cylinders. FALCON SFIC “H” keyway d. “Interior” Door Openings - Patented Key System: Except as otherwise

indicated, provide a NEW Key System for this Project. e. Equip all cylinders and locksets with, a minimum of, 7-pin, interchangeable

core where specified, tumbler cylinders. FALCON SFIC “H” keyway f. Furnish cylinders and locksets with temporary, brass / keyed, “Construction”

interchangeable cores for the duration of the time of construction. Construction cores, master keys, and control keys shall not be part of the Owner’s Permanent Key System or furnished on the same keyway (or key section) as the Owner’s Permanent Key System. Construction cores, master keys, and control keys are the property of the manufacturer and shall be returned when the Permanent cores and keys are installed. Remove these “Construction” interchangeable cores ONLY when directed by the Architect and / or Owner.

g. Furnish final “Permanent” interchangeable cores and keys, for installation by the Owner.

h. Metals: Construct lock cylinder parts from brass or bronze, stainless steel, or nickel silver.

i. Comply with the Owner’s instructions for keying requirements and, except as otherwise indicated, provide individual change keys for each lock that is not designated to be keyed alike with a group of related locks. All keys are to be Patented.

(1) Permanently inscribe each key with number of lock that identifies the cylinder manufacturer’s key symbol, and notation, “DO NOT DUPLICATE”.

8529-02 08710 - 6

j. A key meeting between the Owner and a representative of the successful finish hardware distributor shall be arranged subsequent to the return of the Approved Finish Hardware Schedule. A keying schedule will be established by the finish hardware distributor’s representative and submitted to the Owner, for Approval. After the Owner’s review, the keying schedule shall be returned to the distributor’s representative such that the Permanent cores and keys can be prepared on a timely basis.

k. Permanent cores and keys will be transmitted directly to the Owner by the Finish Hardware Distributor. The Owner shall be responsible for the installation of the Permanent cores and the return of the Construction cores and keys.

l. Key Material: Provide keys of nickel silver only. m. Key Quantities: Furnish the following quantities of keys for the entire project.

(1) Ten (10) Each - Construction Master Keys (2) Two (2) Each - Construction Control Keys (3) Five (5) Each - Permanent Master Keys (4) Two (2) Each - Permanent Control Keys (5) Three (3) Each - Permanent Change Keys

(For Each Keyed Door Opening) Notes: Furnish ALL Permanent Keys as Patented Keys

The “Exterior” and “Interior” Permanent Interchangeable Cores Cylinders shall be operated by the same Patented Keys.

Deliver all Construction interchangeable cores and keys to the General Contractor. Deliver all Permanent interchangeable cores and keys to the Owner, via Registered Mail.

2.05 CYLINDRICAL LATCHSETS AND LOCKSETS: Characteristics:

a. Tested to be in accordance with or exceed ANSI / BHMA A156.2, Series 4000, Grade 1 Strength and Operational requirements, including, a minimum of, 3,000,000 cycle testing.

b. U.L. Listed for 3-hour doors. c. Locksets shall be non-handed. d. Chassis: Cylindrical housing design, heavy gauge, cold rolled steel

mechanisms, corrosion treated for normal atmosphere conditions. e. Locksets shall have separate anti-rotational through-bolts for positive

mounting / interlocking to the door, without any exposed mounting screws. f. Locksets shall have solid cast levers, plated to match the specified finish

symbols. Levers shall operate independently, and shall have separate, heavy duty, lever return springs or spring cages, allowing for a smooth operation of the lockset, for effective lever support, which shall prevent lever sag. Outside lever handles shall be a minimum of 4-5/8” in length and shall provide a minimum of 2” clearance from the surface of the door to the inside of the lever, at the midpoint. Outside lever handles shall return to within, a maximum, of 1/2” of the door surface.

8529-02 08710 - 7

g. Outside lever handles, on keyed locksets, shall be removable only when the designated key is in the cylinder.

h. When the outside lever handle is locked, the lever shall rotate freely and shall return to its horizontal position when released. The locked outside lever handle shall freely rotate up and down while remaining securely locked.

i. Roses: Wrought brass, bronze or stainless steel, plated to match the specified finish symbols. Roses shall be a minimum 3-7/16” in diameter, for coverage of the ANSI / DHI A115.18 - 1994 door preparation.

j. All locksets shall be furnished with a 1/2” throw latch bolt and shall be listed by Underwriters Laboratories, Inc. for A label and lesser class 4’-0” x 10’-0” single doors.

k. Backset: 2-3/4”. l. Strike: Brass, bronze or stainless steel, plated to match the specified finish

symbols. Conform to ANSI A115.2 (4-7/8” x 1-1/4”), with lips of a sufficient length to clear trim and protect clothing.

m. Provide “Knurled” or “Tactile” Outside Levers; as indicated in the Door Hardware Sets.

“Abrasive” Outside Levers shall not be acceptable. 2.05 Mortise Locksets

Characteristics:

a. Tested to be in accordance with or exceed ANSI / BHMA A156.13 Series 1000, Grade 1 Strength

b. U.L. Listed for 3-hour doors. c. Levers and escutcheons as specified in sets d. Manufactured by Schlage Lock Company.

2.07 EXIT DEVICES: Characteristics:

a. Tested to be in accordance with ANSI A156.3, 1994, Grade 1. All exit devices to be heavy duty, with one-piece removable covers. The housing shall be manufactured from extruded aluminum without exposed screws or rivets.

b. Exit Devices shall be “UL” listed for Life Safety. All exit devices for fire-rated door openings shall have “UL” labels for “Fire Exit Hardware”. All exit devices shall conform to NFPA 80 and NFPA 101 requirements.

c. All series exit devices shall be “touchpad” (modern) types, incorporating a hydraulic fluid damper, which decelerates the touchpad on its return stroke and eliminates noise associated with the exit device operation. All exit devices shall be non-handed. The touchpad shall extend a minimum of 1/2 of the door width and shall be a minimum of 2-3/16” in height. Plastic touch pads shall not be acceptable. The touchpad height shall exceed height of mechanism case or rail assembly to eliminate “Pinch Points”. If the touchpad height does not exceed the height of the mechanism case or rail assembly, provide a factory installed insert / filler on the top and bottom of the touchpad along the mechanism case and rail assembly; to prevent “Pinch Points”.

8529-02 08710 - 8

d. All latch bolts to be the deadlocking type. Latch bolts shall have a self-lubricating coating to reduce wear.

Plated or plastic coated latch bolts shall not be acceptable. e. All metal end caps to be standard with all exit devices. f. Exit device strikes, where surface applied, shall be a roller type and have an

anti-slip mounting plate. g. All outside exit device trim shall be forged brass, full escutcheon. The lever

trim shall be a “breakaway type” with substantial resistance to rotation when locked but allowing the vandalized lever to drop to a vertical, 90 degrees, position when more than 35 pounds of torque is applied.

h. The exit device end caps shall be secured with three (3) screws to a truss bracket.

i. The “touchpad” exit devices shall be patterned punched to designate code requirements; where required.

j. All exit devices shall be made of brass, bronze, stainless steel, or aluminum material, plated to the standard architectural finishes to match the balance of the door hardware.

2.08 CLOSERS Characteristics:

a. Door closers shall have fully hydraulic, full rack and pinion action with a high strength cast iron cylinder; which have been tested and certified under ANSI / BHMA Standard A156.4, Grade 1.

b. Hydraulic fluid shall be of a type requiring no seasonal closer adjustment for temperatures ranging from 120 degrees F (49 degrees C) to -30 degrees F (-35 degrees C).

c. Spring power shall be continuously adjustable over the full range of closer sizes, and allowing for reduced opening force for the physically handicapped. Hydraulic regulations shall be by tamper-proof, non-critical valves. Closers shall have separate adjustment for latch speed, general speed and back check.

d. All closers shall have solid forged steel main arms (and forearms for parallel arm closers) and where specified shall have a spring loaded stop in the soffit shoe (“SPRING CUSH-N-STOP”); as indicated in the Door Hardware Sets. Where door travel on out-swing doors must be limited, use SPRING CUSH-N-STOP type closers. Auxiliary stops are not required when SPRING CUSH-N-STOP type closers are used.

e. All closers shall have non-metallic full, plastic, covers, which provides complete enclosure.

f. All closers shall be certified to exceed Ten Million (10,000,000) full load cycles by a recognized independent testing laboratory. All closers shall be of one manufacturer and shall maintain the manufacturer’s ten year warranty.

g. Access-Free Manual Closers: Where manual closers are indicated for doors required to be accessible to the physically handicapped, provide adjustable units complying with ADA and ANSI A117.1 provisions for door opening force.

h. All closers shall be attached utilizing Through Bolts with Wood and Machine Screws (“TBWMS”).

8529-02 08710 - 9

i. Closers to be installed to allow door swing as shown on plans. Doors swinging into exit corridors shall provide for corridor clear width as required by code. Where possible, mount closers inside rooms.

j. Powder coating finish to be certified to exceed 100 hours salt spray testing by ETL, an independent testing laboratory used by BHMA for ANSI certification.

Lacquer or painted finish on metal components shall not be acceptable.

2.09 PUSH AND PULL UNITS PULL UNITS:

Characteristics: a. Tested to be in accordance with ANSI / BHMA A156.6, Grade 1. b. Door Pulls shall be made of 1” diameter material, Semi-Circular offset, 11”

Center-To-Center length, with a minimum of a 3-1/4” projection, and a 2-1/4” clearance. The door pulls shall comply with the recommendations of the Americans with Disabilities Act (A.D.A.).

c. Provide door pulls with 1/8” thick base washers; as indicated in the Door Hardware Sets.

d. Fasteners: Provide two (2) 5/16-18 x 2-1/4” machine screws with 1” Diameter Decorative Thru-Bolts.

e. Custom pulls shall be manufactured by Rockwood, product numbers listed in hardware sets.

PUSH PLATES:

Characteristics: a. Tested to be in accordance with ANSI / BHMA A156.6, Grade 1. b. Push Plates shall be made of .050” wrought, stainless steel material. c. Where detailed, provide 8” x 16” “Half Circle”. d. Where detailed, provide push plates cut for a cylinder (CFC). e. Provide exposed, Phillips oval head, stainless steel, sheet metal screw,

mounting fasteners, for all plates.

2.10 PROTECTIVE PLATES

Characteristics: a. Tested to be in accordance with ANSI / BHMA A156.6, Grade 1. b. All mop, kick, and armor plates shall be US18 gauge (.050”) thick of stainless

steel material. c. Fabricate mop plates not more than 1 inch less than door width, on the

“PULL” side, kick plates not more than 1-1/2 or 2 inches less than door width, on the “PUSH” side, and armor plates not more than 1-1/2 inches less than door width, on the “PUSH” side.

d. Heights: (1) Mop Plates shall be 4 inches in height. (2) Kick Plates shall be 12 inches in height. (3) Armor Plates shall be 36 inches in height.

8529-02 08710 - 10

e. Where detailed bevel all four (4) edges (“B4E”). f. Provide mop, kick, and armor plates with #6 x 5/8” Oval Head, Stainless

Steel, Sheet Metal Screws. 2.11 THRESHOLDS

Characteristics: a. All thresholds shall be certified by an independent testing laboratory to meet

the requirements of ANSI / BHMA A156.21. b. All thresholds shall be in accordance with the requirements of A.D.A.A.G.

and ICC / ANSI A117.1. c. Thresholds shall be furnished in an aluminum extrusion that is of alloy 6063

hardness T-5. d. Provide thresholds with 1/4-20 Stainless Steel Machine Screws and Lead

Anchors.

2.12 DOOR STOP Characteristics:

a. Tested to be in accordance with ANSI / BHMA A156.16, Grade 1. b. Wall Bumpers shall have a solid forged brass housing with a concealed, in

the concave bumper, attachment. Provide with wood screw and plastic anchors.

c. Floor Stops shall be made from solid cast brass or bronze. Provide with machine screws and lead expansion shield anchors.

d. Install floor stops in such a position that they permit maximum door swing, but do not present a hazard or obstruction.

2.13 SILENCERS

Provide GJ-64 silencers for all hollow metal frames. Single doors shall have three (3) silencers. Double doors shall have two (2) silencers.

PART 3 – EXECUTION

3.01 APPLICATION

INSTALLATION: Work shall be done by a craftsman skilled and experienced in installation of finish hardware. Mortised items shall be neatly set in and made flush with door or frame surface. Manufacturer’s instructions and recommendations shall be strictly followed. FASTENERS: Hinges, pivots, locks, and exit devices shall be installed with proper sex bolts, wood or machine screws as supplied by the manufacturer. Surface closers shall be mounted to door with sex bolts. Door pulls shall be installed on doors with thru-bolts as supplied by manufacturer.

8529-02 08710 - 11

3.02 ADJUSTING, CLEANING, AND DEMONSTRATING

A. Adjust and check each operating item of hardware and each door to ensure proper operation or function of every unit. Replace units that cannot be adjusted to operate freely and smoothly or as intended for the application made.

1. Where door hardware is installed more than one month prior to

acceptance or occupancy of a space or area, return to the installation during the week prior to acceptance or occupancy to execute final check and adjustment of all hardware items in such space or area. Clean operating items as necessary to restore proper function and finish of hardware and doors. Adjust door control devices to compensate for final operation of heating and ventilating equipment.

B. Clean adjacent surfaces soiled by hardware installation.

C. Door Hardware Supplier’s Field Service:

To be inspected and certified by a certified Fire Door Assembly Inspector. Contact Brian K Baylor, AHC/FDAI at 606-528-5359

1. Inspect door hardware items for correct installation and adjustment

after complete installation of the door hardware. 2. Instruct the Owner’s personnel in the proper adjustment and

maintenance of the door hardware and hardware finishes. 3. File a written report of this inspection to the Architect.

3.03 Door Hardware to be Provided by: Baylor Commercial Door & Hardware, Inc.

101 23rd Street Ste 100 Corbin, KY 40701 Ph. 606-528-5359 Fax 606-528-5359 E-mail: baylorcommercial@bellsouth.net

8529-02 08710 - 12

3.04 Hardware Sets Hardware Set 1 Tag # 01 Continuous Hinge 780-112 HD x EPT Electric Power Transfer EPT-2 Rim Exit EL 33A NL-OP Rim Exit EL 33A EO Pulls RM 7240 Mullion 5754 x 1408 strike Rim Cylinder C953 Mortise Cylinder C987 x #5cam Power Supply PS914 x 900 2RS x 900 4R NOTE: Threshold and Weather Strip by Aluminum Door Supplier NOTE: Automatic Operator listed in separate specification and to be provided by Baylor Commercial Door & Hardware, Inc. Ph#606-528-5359 NOTE: Card Reader to be supplied by security sub contractor Hardware Set 2 Tag # 02, 05, 09, 10, 15, 23, 34, 36, 40 Ball Bearing Hinges BB1199 NRP 4.5 x 4.5 630 Rim Exit 99EO Closer 4041 S-Cush Bumper Threshold 477S-S Weather Strip 881S-S Door Sweep 802S-S NOTE: Weather Strip to be applied prior to exit device and closer Hardware Set 3 Tag # 16, 17, 25, 28, 29, 31, 35, 42, 43 Ball Bearing Hinges BB1199 NRP 4.5 x 4.5 630 Rim Exit CD99 NL Rim Cylinder C953 Mortise Cylinder C987 x #5 cam Closer 4041 S-Cush Bumper Threshold 477S-S Weather Strip 881S-S Door Sweep 802S-S NOTE: Weather Strip to be applied prior to exit device and closer

8529-02 08710 - 13

Hardware Set 4 Tag # 26, 22 Continuous Hinge 780-112 HD x EPT Electric Power Transfer EPT-2 Rim Exit SD EL 99 NL-OP Rim Exit SD EL 99 EO Pulls 12L Mullion 5754 x 1408 strike Rim Cylinder C953 Mortise Cylinder C987 x #5cam Closer XP4041 SH-Cush Power Supply PS914 x 900 2RS x 900 4R Bumper Threshold 477S-S Weather Strip 881S-S Door Sweep 802S-S NOTE: Weather Strip to be applied prior to exit device and closer NOTE: Card Reader to be supplied by security sub contractor Hardware Set 4-1 Tag # 06 Continuous Hinge 780-112 HD x EPT Electric Power Transfer EPT-2 Rim Exit SD EL 99 NL-OP Pulls 12L Rim Cylinder C953 Mortise Cylinder C987 x #5cam Closer XP4041 SH-Cush Power Supply PS914 x 900 2RS x 900 4R Bumper Threshold 477S-S Weather Strip 881S-S Door Sweep 802S-S NOTE: Weather Strip to be applied prior to exit device and closer NOTE: Card Reader to be supplied by security sub contractor Hardware Set 5 Tag # 12, 97, 98, 99, 100, 101 Ball Bearing Hinges BB1191 4.5 x 4.5 630 Mortise Lockset L9080 HD 06L Closer 4041 H Threshold 413S Auto Door Bottom 740S-N Weather Strip 881S-S Door Sweep 802S-S Permanent Core C607

8529-02 08710 - 14

Hardware Set 6 Tag # 18, 19, 20 Ball Bearing Hinges BB1199 NRP 4.5 x 4.5 630 Flush Bolt 282R 25” top Flush Bolt 282D 12” bottom Dust Proof Strike 280X Mortise Lockset L9480 HD 06L Surface Overhead Stop 906H Saddle Threshold 413S Weather Strip 736S Door Sweep 759S-V Permanent Core C607 Meeting Stile Astragal 802S (mount pull side of active door as pest conrol) Z-astragal by Hollow Door Manufacturer Hardware Set 7 Tag # 24 Ball Bearing Hinges BB1199 NRP 4.5 x 4.5 630 Flush Bolt 282D x 282D Mortise Lockset L9480 HD 06L Surface Overhead Stop 904H inactive Closer XP4041 H-Cush Saddle Threshold 413S Weather Strip 736S Door Sweep 759S-V Permanent Core C607 Meeting Stile Astragal 802S (mount pull side of active door as pest conrol) Z-astragal by Hollow Door Manufacturer Hardware Set 8 Tag # 44 Ball Bearing Hinges BB1279 4.5 x 4 652 Rim Exit 99 L-F Rim Cylinder C953 Mortise Cylinder C987 x #5 cam Closer XP4041 Kick Plate 194S 16” x 2” LTDW Smoke Seal 726S Door Sweep 802S-S Hardware Set 9 Tag # 45, 113, 140 Ball Bearing Hinges BB1279 4.5 x 4 652 Storeroom Lockset ND80 BD RHO Surface Overhead Stop 904S

8529-02 08710 - 15

Permanent Core C607 Hardware Set 10 Tag # 46, 48, 57, 58, 75, 76, 82, 83, 92, 95 Ball Bearing Hinges BB1279 4.5 x 4 4 ea @ 8’0 652 Flush Bolt 282D x 282D use 24” @8’0 Dead Bolt B600 BD Push Plate 30S 8” x 16” Drill for Deadlock Offset Pull 12G mounted to 8” x 16” drill for deadlock Closer XP4041H (w/PA as required) Armor Plate 194S 34” x 1” LTDW Permanent Core C607 Meeting stile astragal (set) 802S-S Threshold 413S Door Sweep 802S-S Hardware Set 11 Tag # 49, 69, 86 Ball Bearing Hinges BB1168 5 x 4.5 652 Rim Exit CD 99 NL-OP Rim Exit CD 99 EO Offset Pull 12J Key Rem. Mullion KR4954 Rim Cylinder C953 Mortise Cylinder C987 x #5cam Closer XP4041 SH-Cush Kick Plate 194S 16” x 2” LTDW Weather Strip 736S Door Sweep 802S-S Threshold 413S Mullion Seal 734S Hardware Set 12 Tag # 50, 120, 121, 122, 123, 124, 125, 126, 127, 130, 134, 135, 136,

137, 141, 143, 144, 145, 146, 148, 149 Ball Bearing Hinges BB1279 4.5 x 4 652 Office Lockset ND50 BD RHO Convex Wall Stop 232W Permanent Core C607 Hardware Set 13 Tag # 51, 52, 53, 59, 60, 70, 71, 88, 89, 132, 133, 139 Ball Bearing Hinges BB1168 4.5 x 4.5 652 Push Plate 110S Offset Pull 12J

8529-02 08710 - 16

Closer XP4041 Rw/PA Kick Plate 194S 16” x 2” LTDW Convex Wall Stop 232W Hardware Set 14 Tag # 54, 65 Ball Bearing Hinges BB1279 4.5 x 4 652 Flush Bolt 282D x 282D Dust Proof Strike 280X Office Lockset ND50 BD RHO Surface Overhead Stop 904H Saddle Threshold 413S Auto Door Bottom 740S-N Weather Strip 881S-S Permanent Core C607 NOTE: Z-Astragal by Door provider Hardware Set 15 Tag # 55, 61, 62, 66, 67, 85, 87, 90, 96, 147 Ball Bearing Hinges BB1279 4.5 x 4 652 Office Lockset ND53 BD RHO Closer XP4041 Rw/PA Weather Strip 881S-S Convex Wall Stop 232W Permanent Core C607 NOTE: Apply weather strip prior to closer Hardware Set 16 Tag # 63, 64 Ball Bearing Hinges BB1279 4.5 x 4.5 652 Flush Bolt 282D x 282D Dust Proof Strike 280X Classroom Lockset ND70 BD RHO Surface Overhead Stop 904H Permanent Core C607 Hardware Set 17 Tag # 68 Ball Bearing Hinges BB1279 4.5 x 4 652 Storeroom Lockset ND80 BD RHO Closer 4041 Rw/PA Convex Wall Stop 232W

8529-02 08710 - 17

Permanent Core C607 Hardware Set 18 Tag # 79, 80 Ball Bearing Hinges BB1279 4.5 x 4.5 652 Auto Flush Bolt 293D Dust Proof Strike 280X Coordinator 297D Storeroom Lockset ND80 BD RHO Closer XP4041 Rw/PA Smoke Seal 736S Permanent Core C607 NOTE: Z-Astragal by Door provider NOTE: Install coordinator prior to closer Hardware Set 19 Tag # 8, 56, 72, 73, 74, 77, 78 Ball Bearing Hinges BB1279 4.5 x 4.5 4ea@ 8’0 652 Surface Vertical Rod Exit 9927 L F Surface Vertical Rod Exit 9927 EO Rim Cylinder C953 Closer XP4041 EDA Smoke Seal 736S Astragal 872S (set) Hardware Set 20 Tag # 81 Ball Bearing Hinges BB1279 4.5 x 4 652 Office Lockset ND53 BD RHO Closer 4041 Rw/PA Convex Wall Stop 232W Smoke Seal 736S Permanent Core C607 Hardware Set 21 Tag # 84 Ball Bearing Hinges BB1279 4.5 x 4.5 652 Flush Bolt 282D x 282D

8529-02 08710 - 18

Office Lockset ND53 BD RHO Surface Overhead Stop 904S inactive Closer 4041 Rw/PA Kick Stop 271D Permanent Core C607 Hardware Set 22 Tag # 94 Ball Bearing Hinges BB1279 4.5 x 4 652 Office Lockset ND50 BD RHO Closer 4041 Rw/PA Convex Wall Stop 232W Smoke Seal 736S Door Sweep 802S-S Threshold 413S Permanent Core C607 Hardware Set 23 Tag # 102, 114, 116, 118, 131, 138 Ball Bearing Hinges BB1279 4.5 x 4 652 Office Lockset ND53 BD RHO Closer XP4041 Rw/PA Convex Wall Stop 232W Permanent Core C607 Hardware Set 24 Tag # 110, 111 Ball Bearing Hinges BB1279 4.5 x 4 652 Mortise Privacy Latchset L9496 BD 06L Closer XP4041 Rw/PA Convex Wall Stop 232W Permanent Core C607 Hardware Set 25 Tag # 112 Ball Bearing Hinges BB1168 5 x 4.5 652 Rim Exit CD 99 NL-OP Rim Exit CD 99 EO Pull RM 7210 Key Rem. Mullion KR4954 Rim Cylinder C953 Mortise Cylinder C987 x #5cam Closer XP4041 SH-Cush Kick Plate 194S 16” x 2” LTDW Hardware Set 26 Tag # 142 Ball Bearing Hinges BB1279 4.5 x 4 652

8529-02 08710 - 19

Passage Latchset ND10S RHO Convex Wall Stop 232W Hardware Set 27 Tag # 117 Ball Bearing Hinges BB1279 4.5 x 4 652 Roller Latch 1433 5” Backset (in head) Dummy Lever ND170 RHO Surface Overhead Holder 904H Hardware Set 28 Tag # 115, 119 Ball Bearing Hinges BB1279 4.5 x 4 652 Privacy Latchset ND40S RHO Convex Wall Stop 232W Hardware Set 29 Tag # 128 Ball Bearing Hinges BB1168 5 x 4.5 652 Rim Exit CD 99 NL-OP Offset Pull 12J Rim Cylinder C953 Mortise Cylinder C987 x #5cam Closer XP4041 H-Cush Hardware Set 30 Tag # 129 Ball Bearing Hinges BB1168 5 x 4.5 652 Push Plate 110S Pull RM7210 Closer XP4041 H Hardware Set 31 Tag # 150 Ball Bearing Hinges BB1279 4.5 x 4.5 652 Flush Bolt 282D x 282D Dummy Lever ND170 inactive Office Lockset ND53 BD RHO Closer XP4041 Hw/PA Permanent Core C607 Hardware Set G1 Tag # G1, G2

8529-02 08710 - 20

Ball Bearing Hinges BB1191 4.5 x 4.5 630 Mortise Lockset L9056 BD 06L Closer XP4041 H Reg Threshold 422S Auto Door Bottom 740S-N Weather Strip 881S-S Permanent Core C607 Hardware Set G2 Tag # G3 Ball Bearing Hinges BB1191 4.5 x 4.5 630 Privacy Latchset ND40S RHO Convex Wall Stop 232W Hardware Set G3 Tag # G4, G5 Ball Bearing Hinges BB1279 4.5 x 4 652 Passage Latchset ND10S RHO Convex Wall Stop 232W

8529-02 08710 - 21

DOOR HARDWARE INDEX Hardware Hardware Hardware Tag# Set # Tag# Set # Tag# Set # 01 1 51 13 100 5 02 2 52 13 102 22 03 -- 53 13 110 24 04 -- 54 14 111 24 05 2 55 15 112 25 06 4-1 56 19 113 9 07 -- 57 10 114 26 08 8 58 10 115 24 09 2 59 13 116 26 10 2 60 13 117 27 11 -- 61 15 118 26 12 5 62 15 119 28 13 -- 63 16 120 12 14 -- 64 16 121 12 15 2 65 14 122 12 16 3 66 15 123 12 17 3 67 15 124 12 18 6 68 17 125 12 19 6 69 11 126 12 20 6 70 13 127 12 21 -- 71 13 128 29 22 -- 72 18 129 30 23 2 73 18 130 12 24 7 74 18 131 26 25 3 75 10 132 12 26 4 76 10 133 12 27 -- 77 18 134 12 28 3 78 18 135 12 29 3 79 18 136 12 30 -- 80 18 137 12 31 3 81 19 138 23 32 -- 82 10 139 12 33 4 83 10 140 9 34 2 84 20 141 12 35 3 85 15 142 26 36 2 86 11 143 12 37 -- 87 15 144 12 38 -- 88 13 145 12 39 -- 89 13 146 12 40 -- 90 15 147 15 41 2 91 -- 148 12 42 3 92 10 149 12 43 3 93 -- 150 31 44 8 94 21 45 9 95 10 46 10 96 15 47 -- 97 5 48 10 98 5 49 11 98 5 50 12 99 5