Upload
ontwerperbart
View
480
Download
0
Embed Size (px)
DESCRIPTION
Citation preview
http://designforeveryone.howest.be/
TOOTHBRUSH
http://designforeveryone.howest.be/
Bart Catoor / Maaike Kock
1 hour 40 minutes€ 25
http://tandenborstel2011.blogspot.com/
ASSEMBLY MANUAL
http://designforeveryone.howest.be/
BILL OF MATERIAL- 2 x candy containers with hinge- 4 x table clamp- 2 x plastic strap 5 mm- 100 x 100 mm adhesive nonslip foil- 100 x 500 mm perspex 3 mm thick- (super glue)
TOOTHBRUSH 1.5
Wood clamp, lassercutter/fretsaw, cutter
Eight
Twelve
1DESCRIPTION Lasercut or saw all
parts out of the piece of perspex.
When lasercutting, 4 extra spacers are cut asspare parts.
TOOTHBRUSH 1.5
Yes
30 minutes
Lasercutter or fretsaw
Perspex
N/a
€ 15
2DESCRIPTION Glue two table clamps
onto the bottom of each container. Fixate for 10minutes.Glue two spacers next to the hinge onto eachcontainer.
No
24 minutes
Super glue for plastics, wood clamp
2 x container, 4 x table clamps
Eight
€ 0
TOOTHBRUSH 1.5
3
No
5 minutes
Cutter
Adhesive nonslip foil
Four
€ 0
TOOTHBRUSH 1.5
DESCRIPTION Cut out 4 pieces of 10 x
35 mm out of the nonslip foil. Attach them tothe table clamps so the foil will touch the table.
4
No
12 minutes
Super glue
N/a
Two
€ 0
TOOTHBRUSH 1.5
DESCRIPTION Glue a lever onto the
top of each container and fixate for 10 minutes
5DESCRIPTION Position and glue two
spacers onto the lever.
No
2 minutes
Super glue
N/a
Two
€ 0
TOOTHBRUSH 1.5
6DESCRIPTION Put one of the plastic
straps through the other, then position the twothickenings at a distance of 24 mm and cut theremaining end. Put the other strap through thelever holes and through the remaining tickening.Do not tighten yet.
No
5 minutes
Cutter
Plastic straps
Two
€ 0
TOOTHBRUSH 1.5
7DESCRIPTION Take your electric
toothbrush and put the lever with plastic strapsaround it. Position the spacer onto the buttonand try until you get the positioning right. Thentighten the strap as tight as you can and cut theremaining end.
No
2 minutes
Cutter
None
One
€ 0
TOOTHBRUSH 1.5
8
No
10 minutes
Cutter
Adhesive nonslip foil
One
€ 0
DESCRIPTION Take the adhesive
nonslip foil and cut it out using the big ring as atemplate and attach it to the big ring.
TOOTHBRUSH 1.5
9
No
10 minutes
Super glue
None
Three
€ 0
TOOTHBRUSH 1.5
DESCRIPTION Take the big ring and
the open ring and glue them onto of each other.Put the charger inside the glued rings and gluethe closed ring onto the open ring. Put somepressure on it.
TECHNICAL ADDENDUM
http://designforeveryone.howest.be/
Lasercut parts with Adobe Illustrator file.
TEAM CONTACTS
http://designforeveryone.howest.be/
[email protected] +32 4 99 32 82 70
[email protected] +32 4 98 64 05 29
[email protected] +32 4 86 39 65 75
[email protected]@HOWEST.BE
http://designforeveryone.howest.be/