POWER ELECTRONICSS.No

CODE PROJECT TITLE

1 ET13PE1

Voltage-Based Control of a Smart Transformer in a Micro grid

DESCRIPTION

For the islanded operation of a micro grid, several control strategies have been developed. For example, voltage based droop control can be implemented for the active power control of the generators & the control of the active loads.

2 ET13PE2

Novel High Step-Up DC–DC Converter for Distributed Generation System

DESCRIPTION

In this paper, a novel high step-up dc–dc converter for distributed generation systems is proposed. Concept is to utilize two capacitors & one coupled inductor. The two capacitors are charged in parallel during the switch-off period and are discharged in series during the switch-on period by the energy stored in the coupled inductor to achieve a high step-up voltage gain.

3 ET13PE3

Maximum Power Point Tracking Technique for Partially Shaded

Photovoltaic Systems in Micro grids

DESCRIPTION

A modified fuzzy-logic controller for maximum power point (MPP) tracking is proposed to increase photovoltaic (PV) system performance during partially shaded conditions. Instead of perturbing and observing the PV system MPP, the controller scans and stores the maximum power during the perturbing and observing procedures.

4 ET13PE4

Digital Control for an ArcWelding Machine Based on Resonant Converters and Synchronous Rectification

DESCRIPTION

This paper presents a optimized drive signals for resonant converters using synchronous rectification (SR) applied to an arc welding machine.

5 ET13PE5

An Energy-Stored Quasi-Z-Source Inverter for Application to Photovoltaic

Power System

DESCRIPTION

This paper proposes a new topology of the energy-stored qZSI. The operating characteristic of the proposed solution is analyzed in detail. 2-strategies are proposed with the related design principles to control the new energy-stored qZSI when applied to the PV power system.

6 ET13PE6

Battery Charger for Electric Vehicle Traction Battery Switch Station

DESCRIPTION

This paper presents the functionality of a commercialized fast charger for a lithium-ion electric vehicle propulsion battery. The device is intended to operate in a battery switch station, allowing an up-to 1-h recharge of a 25-kWh depleted battery.

7 ET13PE7

Bifurcation Analysis of Standalone Photovoltaic- Battery Hybrid Power

System

DESCRIPTION

Standalone photovoltaic-battery hybrid power systems are attractive renewable power generation systems, a popular form of which is based on a photovoltaic system and

a battery connected to an output dc bus via a buck converter & a bidirectional buck/boost converter.

8 ET13PE8

Boost rectifier using single phase matrix converter with reduced switch

counts

DESCRIPTION

This paper focuses on implementation of computer simulation for boost rectifier operation using single-phase matrix converter topology with reduced switch counts. Proposed topology employed only six switches compared with the conventional boost rectifier operation using single phase matrix converter topology used eight main switches.

9 ET13PE9

New Extendable Single-Stage Multi-Input DC-DC/AC Boost Converter

DESCRIPTION

This paper presents a new extendable single-stage multi-input DC-DC/AC boost converter. The proposed structure comprises two bidirectional ports in the converter central part to interface output load and battery storage, and several unidirectional input ports to get powers from different input dc sources.

10 ET13PE10

A Modified Single-Phase Quasi-Z-Source AC–AC Converter

DESCRIPTION

A modified single-phase quasi-Z-source ac–ac converter is proposed in this paper. Proposed converter has the main features in that the O/P voltage can be bucked or boosted and be both in-phase& out-of-phase with the I/P voltage

11 ET13PE11

Highly Efficient Analog Maximum Power Point Tracking (AMPPT) in a

Photovoltaic System

DESCRIPTION

Compact-size analog maximum power point tracking (AMPPT) technique is proposed in this paper for high power efficiency in the photovoltaic (PV) system. Combining existing MPPT approaches, we present a fast & accurate tracking performance.

12 ET13PE12

A New Cascaded Multilevel Inverter with

Reduced Number of Switches

DESCRIPTION

This paper propose a new topology for cascaded multilevel inverters. This structure consists of series connection of proposed basic unit blocks which are built with both unidirectional and bidirectional switches.

13 ET13PE13

Boost-Derived Hybrid Converter with simultaneous DC and AC outputs

DESCRIPTION

The paper proposes a family of hybrid converter topologies which can supply simultaneous DC as well as AC loads from a single DC input. These topologies are realized by replacing the controlled switch of single-switch boost converters with a voltage source inverter (VSI) bridge network.

14 ET13PE14

Flexible Multilevel Boost DC-AC Converter

DESCRIPTION

In this paper, incorporation of MULTI-output boost (MOB) converter by multilevel inverter is proposed. Renewable energy sources such as fuel cell and photovoltaic produce low level of voltage. So to increase the magnitude of voltage, dc-dc boost converter is used.

15 ET13PE15

Improved ZVS DC-DC Converter With a High Voltage Gain and a Ripple-Free

Input Current

DESCRIPTION

An improved zero-voltage-switching (ZVS) dc-dc converter with high voltage gain & ripple-free I/P current is proposed. It consists two converter cellsa boost cell and an asymmetrical pulse-width-modulation (APWM) full-bridge cell. Boost cell in the proposed converter has capabilities of providing a ripple-free i/p current.

16 ET13PE16

A Soft Switching Three-phase Current-fed Bidirectional DC-DC Converter With

High Efficiency Over a Wide Input Voltage Range

DESCRIPTION

In this paper, a three-phase current-fed dual-activebridge (DAB) bidirectional DC-DC converter is presented. Compared to the voltage source DAB converter, the proposed converter allows low RMS current and maintains zero voltage switching (ZVS) in the whole operating range by keeping the ratio between primary side and secondary side DC-link voltage constant, leading to high efficient energy conversion over a wide

input voltage range.17 ET13

PE17Cascade Three-Level AC/AC Direct

Converter

DESCRIPTION

This paper proposes a novel family of cascade threelevel (TL) ac–ac direct converters based on ac switch cells, which transfer unsteady high ac voltage with distortion into regulated sinusoidal voltage with low total harmonic distortion (THD).

18 ET13PE18

Grid-Connected Boost-Half-Bridge Photovoltaic Microinverter System

Using Repetitive Current Control and Maximum Power Point Tracking

DESCRIPTION

This paper presents a novel grid-connected boost half- bridge photovoltaic (PV) micro inverter system and its control implementations. In order to achieve low cost, easy control, high efficiency, and high reliability, a boost-half-bridge dc–dc converter using minimal devices is introduced to interface the low-voltage PV module.

19 ET13PE19

Novel Zeta-Mode Three-Level AC Direct Converter

DESCRIPTION

An improved zero-voltage-switching (ZVS) dc-dc converter with a high voltage gain and a ripple-free input current is proposed. It consists of two converter cells—a boost cell and an asymmetrical pulse-width-modulation (APWM) full-bridge cell. Boost cell in proposed converter has capabilities of providing ripple-free I/p current.

20 ET13PE20

Step-Up DC/DC Converters With Cascaded Quasi-Z-Source Network

DESCRIPTION

The proposed cascaded qZSI inherits all the advantages of the traditional solution .Moreover, as compared to the conventional qZSI, the proposed solution reduces the shoot-through duty cycle by over 30% at the same voltage boost factor.

POWER SYSTEMS.No

CODE PROJECT TITLE

1 ET13PS1

Improvement of power quality by using hybrid fuzzy controlled based IPQC at

various load conditions

DESCRIPTIONThis paper presents a hybrid fuzzy logic controlled based improved power quality conditioner used to counterbalance for harmonic distortion in 3-phase system.

2 ET13PS2

A Method for Evaluating Energy Efficiency to Justify Power Factor Correction in Ship Power Systems

DESCRIPTION

This paper presents the methodology and results for the economic evaluation of PFC in marine vessels. A mathematical model, used to determine the relationships among fuel oil consumption, emission and power factor for the diesel electric generator, is derived to quantify the possible benefits with PFC.

3 ET13PS3

Reactive Power Compensation in Single-Phase Operation of Microgrid

DESCRIPTION

A coordinated control of distributed generators (DG) and distribution static compensator (DSTATCOM) in a micro grid is proposed in this paper. With high penetration of distributed sources and single-phase operation of the system, voltage unbalance can often go beyond the acceptable limit.

4 ET13PS4

Technique to Develop Auto Load Shedding &

Islanding Scheme to Prevent Power System Blackout

DESCRIPTION

Abnormal condition in a power system generally leads to a fall in system frequency, and it leads to system blackout in an extreme condition. This paper presents a technique to develop an auto load shedding and islanding scheme for a power system to prevent blackout and to stabilize the system under any abnormal condition.

5 ET13PS5

Stabilty Of Power Transmission Capability Of Hvdc System Using Facts

Controllers

DESCRIPTION

a desired power condition at the given points are best achieved using power controllers such as the well known High Voltage Direct Current (HVDC) and Flexible Alternating Current Transmission System (FACTS) devices.

6 ET13PS6

Multi objective Optimal Location of FACTS Shunt-Series Controllers for Power System Operation Planning

DESCRIPTION

This paper develops appropriate models of flexible AC transmission systems (FACTS) shunt-series controllers for multiobjective optimization and also presents a multiobjective optimization methodology to find the optimal location of FACTS shunt-series controllers.

7 ET13PS7

Investigation of Domestic Load Control to Provide Primary Frequency Response Using Smart Meters

DESCRIPTION

The ability of smart meters to control domesticdemand during system emergencies was investigated. In ths project load control scheme that used a local frequency measurement from the smart meters was investigated.

POWER SECTORS S.No

CODE PROJECT TITLE

1 ET13PT1

Computer based Boiler Feed Pump protection and changeover scheme

DESCRIPTION

The Aim of this project is for protecting the Boiler Feed Pump failure and using a changeover scheme by monitoring the required parameters using pc for the continuous power generation.

2 ET13PT2

Incapability of analog relay protection to detect generator stator winding ground failures at neutral end

DESCRIPTION

The electromechanical ground protection relay 59GN commonly used in generator protection does not respond to grounds in the bottom ~5% of the stator winding. this paper will describe newer ground relay systems that monitor and protect the entire stator winding for grounds.

3 ET13PT3

Self-adaptive transformer differential protection

DESCRIPTION

Setting the pickup current and slope of differential relays of power transformer protection is a well-known compromise. It has been the focus of study to improve both the security and sensitivity of transformer differential protection recently. Therefore a novel adaptive protection criterion is proposed in this study,

4 ET13PT4

Application of computer and modern automation system for protection and optimum use of High voltage power

transformer

DESCRIPTION

In this paper an attempt has been made to elaborate the use of computer and modern automation system for protection and optimum use of High voltage power transformer, its advantages and cost effectiveness. Programmable logic controllers (PLC) can be used for control & automation of High voltage power transformer.

5 ET13PT5

Switching and protection of multiple transformer arrangement in industrial

distribution system

DESCRIPTION

In modern industrial electrical distributions, medium size transformers require protection systems that are faster, more reliable and selective than the systems used for their earlier counterparts. To achieve such improved performance, this system is used

6 ET13PT6

Research on the intelligent protection system of coal conveyor belt

DESCRIPTION

A sort of intelligent protection system for conveyor belt was designed, which mainly aimed at the phenomenon of belt slipped, belt broken, overloaded and coupling broken etc. It was designed by using intelligent instrument, monitoring software and fault detection technology, The protection system can automatically detect, diagnose corresponding fault, and give alarm signal with sound and light to stop the fault belt machine in due course. The application effect has proved that the protection system can improve intelligent degree of the whole burning coal transport and reduce the manual greatly and save a lot of funds for enterprise

7 ET13 An Adaptive Fuzzy Mho Relay for Phase

PT7 Backup Protection With Infeed From STATCOM

DESCRIPTION

This paper presents a fuzzy-logic-based scheme for the operation of generator-phase backup distance protection, otherwise popularly known as “phase 21” function, in the presence of a STATCOM installed at the generator bus.

8 ET13PT8

Impact of Power System Instability on Generator Protection

DESCRIPTION

This paper discusses what relay engineers need to know about power system stability, including the four basic types of power system instability. Voltage instability, Steady-state instability, Transient instability &Dynamic instability.

9 ET13PT9

Research on the intelligent protection system of coal conveyor belt

DESCRIPTION

A sort of intelligent protection system for conveyor belt was designed, which mainly aimed at the phenomenon of belt slipped, belt broken, overloaded and coupling broken etc. The protection system can automatically detect, diagnose corresponding fault, and give alarm signal with sound and light to stop the fault belt machine in due course.

10 ET13PT10

Modeling and Simulation of Digital Frequency Relay for Generator

Protection

DESCRIPTION

This paper presents the design and various data conversion steps of a digital frequency relay. The designed relay

will cover both over and under frequency conditions.

11 ET13PT11

Modeling and Simulation of Digital Negative Sequence Relay for Unbalanced Protection of Generator

DESCRIPTIONThis paper presents design & various data conversion steps of a digital negative sequence relay.

12 ET13PT12

Modeling and Simulation of Reverse Power Relay for Generator Protection

DESCRIPTIONThe paper has presented the modeling of digital reverse power relays

13 ET13PT13

Protection of Transformer-Ended Feeders Using Multifunction Relays

DESCRIPTION

In this paper, we describe an application of digital multifunction relays for the protection of a feeder that ends with a distribution transformer. In this application, we attempt to provide as many protection functions as possible with fewest relays.

14 ET13PT14

A Novel Adaptive Dispersed Phase Current Differential Protection Criterion

DESCRIPTION

A novel adaptive dispersed phase current differential protection criterion is proposed in this paper, and an objective function with the independent variable of fault current component and through current is defined to revise the restraining ratio of differential protection criterion adaptively.

15 ET13PT15

Analysis and Solutions of Overcurrent Protection Issues in a Micro grid

DESCRIPTION

In this project The changes cause detrimental effect of sympathetic tripping, blinding of protection, relay over-reaching, relay under-reaching and loss of selectivity of the over current protection scheme of generators in micro grid are discussed

16 ET13PT16

Adaptive Differential Protection for Power Transformer Based on Transient

Signal Analysis

DESCRIPTIONThis paper presents an adaptive relaying scheme for percentage differential protection of 3-phase power transformers.

17 ET13PT17

A New Algorithm to Avoid Maloperation of Transformer (TFr) Differential

Protection in Substations With an Inner Bridge Connection

DESCRIPTION

This paper analyzes the factors that may lead to the maloperation of transformer differential protection and concludes that local transient saturation of the current TFr (CT) caused by the decaying dc component in the magnetizing inrush is the main cause of the maloperation of the TFr differential protection.

18 ET13PT18

A Real Time DSP based Differential Protection of Low Voltage Bus bar

DESCRIPTION

This paper presents design, implementation and testing of low voltage bus bar relaying scheme in laboratory environment using A Digital Signal Processor.

19 ET13 Application of Intelligent Relays to the

PT19 Islanding protection of Multiple Synchronous Generators

DESCRIPTION

This article illustrates how intelligent relays can be used to address DG islanding detection issues spawned by the presence of more than one synchronous generator on a distribution feeder.

20 ET13PT20

A Secure Generator Distance Phase Backup Protection Setting for

Enhancing Generator Over excitation Thermal Capability during System

Disturbances

DESCRIPTION

In this paper, investigations are carried out to explore the impact of generator distance phase backup protection (Relay (21) on the generator over excitation thermal capability.

EMBEDDED & Robotics S.No

CODE PROJECT TITLE

1 ET13EM1

A System for Mobile Assisted Living

DESCRIPTION

The system can detect abnormal situations with the person wearing the wearable part ofthe system (e.g. abnormal heart rate) and send this information to the nursing home so that appropriate action can be taken immediately.

2 ET13EM2

Wireless remote monitor and control system based on Zigbee and web

DESCRIPTION

Considering the present development trend of intelligence, convenience and remoteness in equipment monitoring area, our system employs intelligent sensors based on ZigBee wireless communication technology and executable elements, which is integrated with web applications based on network environment is introduced in this project

3 ET13EM3

Low cost smart power metering

DESCRIPTION in this paper a low cost solution for the real-time energy management in a smart grid, is presented. It provides several smart meters, which act as slaves, that continuously monitor connected loads communicating with data aggregator via CAN-bus.

4 ET13EM4

Remote-Control System of High Efficiency and Intelligent Street

Lighting Using a ZigBee Network of Devices and Sensors

DESCRIPTION The proposed remote-control system can optimize management and efficiency of street lighting systems. It uses ZigBee-based wireless devices which enable more efficient street lamp-system management,

5 ET13EM5

Automatic speed and torque monitoring in induction motors using ZigBee and

SMS

DESCRIPTION This project is for monitoring the speed and torque in induction motors in real time by employing ZigBee based wireless sensor network. The values calculated by the embedded system are transmitted to a monitoring unit through ZigBee based wireless sensor network.

6 ET13EM6

A RISC Microcontroller Based Voltage Regulator Module with Fuzzy Logic

Controller for Processor Core in Mobile Systems

DESCRIPTION This paper describes the design of Buck converter that has a fuzzy controller implemented using a RISC based microcontroller from Atmel series along with a choice of hardware components that will ensure better efficiency while delivering good stability and a dynamic response that complies with requirements of the target processor.

7 ET13EM7

Advanced Virtual Embedded System Laboratory

DESCRIPTION

In this virtual web based laboratory a student can perform experiments, simulations and experimental validation of results virtually using a single PC.

8 ET13EM8

A low cost web based remote monitoring system with built-in security feature for vulnerable environments

DESCRIPTION

This paper mainly focus on the design and implementation of an intelligent, low cost and fully automated system which will be able to provide full time monitoring and eventual security to susceptible environment like gas filling station, research and development laboratories etc.

9 ET13EM9

Automatic Control for Laboratory Sterilization Process based on Arduino

Hardware

DESCRIPTION

In this paper An automated control system for the sterilization process of biological material is introduced. The proposed system is composed of four modules: flame detection, pressure sensor, Gas Control Module and CPU Module. This System is based on Arduino Board.

10 ET13EM10

Online Control of Fuzzy Based Mine Detecting Robot Using Virtual

Instrumentation

DESCRIPTION

In the real time applications detection & location of bomb is highly essential in the field of defense applications. This paper proposes the design of a micro-controller based fuzzy logic controller for a remote controlled mine detecting robot.

11 ET13EM11

Design and Conceptual Development of a Sunbathe Laundry Robot

DESCRIPTION

The main objective of this project is to design and develop a prototype that base on light detection sensor and water detection circuit with both parameters interface with twin motor gearbox for movement purpose.

12 ET13EM12

Design and Implementation of Industrial Network Monitoring Protocol

for Networked Industrial Sensors

DESCRIPTION

in this project a Industrial Network Monitoring Protocol is proposed. the proposed protocol provides device message sets. For maintainability, it provides the fault detection and reporting. For the user’s convenience, it provides a categorized addressing system.

13 ET13EM13

Automatic Measurement and Reporting System of Water Quality Based on GSM

DESCRIPTION

The system consists of multiple sensors of water quality testing, single-chip microcontroller data acquisition module, information transmission module, monitoring center and other Accessories. Various parameters of water quality are automatically detected and the data are instantaneously sent to monitoring center by GSM network in the form of SMS.

14 ET13RO1

Developing a 32-bit microcontroller board for embedded applications

DESCRIPTION

This paper describes development of a 32-bit embedded microcontroller board intended for a broad range of applications.

15 ET13RO2

Online control of remote operated agricultural Robot using Fuzzy Controller and Virtual Instrumentation

DESCRIPTIONThis paper details the design of a micro-controller based fuzzy logic controller for an agricultural Robot which can be used for plugging, seeding and soil moisture sensing.

LABVIEWS.No

CODE PROJECT TITLE

1 ET13LV1

Online control of remote operated agricultural Robot using Fuzzy

Controller and Virtual Instrumentation

DESCRIPTION

This paper details the design of a micro-controller based fuzzy logic controller for an agricultural Robot which can be used for ploughing, seeding and soil moisture sensing

2 ET13LV2

Virtual Lab: Remote Access and Speed Control of DC Motor using Ward-

Leonard System

DESCRIPTION

The objective of this project is to demonstrate the real-time web based laboratory experiment conduction by accessing the laboratory set-up from a remote location and measure the experimental parameters by generating the control commands at a distant client.

3 ET13LV3

The Design of ZigBee Protocol Based Mobile Node in Wireless Sensor

Network

DESCRIPTION

In order to overcome the defects of static wirelesssensor network nodes, such as poor adaptability, communication disruption, lack of dynamic network & so on, a kind of approach to design mobile wireless sensor node is proposed in this paper.

4 ET13LV4

Remote Monitoring and Controlling of Gas Sensors Using VPN Connection

DESCRIPTION

The use of sensors is witnessing a dramatic increase. They are applied in diverse fields such as military, industrial, health, and smart homes. Monitoring these sensors could be made remotely with the help of communication networks. Using Labview

5 ET13LV5

Oxygen Level Monitoring in an Oxygen Cylinder

DESCRIPTION

The amount of oxygen present inside the cylinder is measured by the pressure at the outlet nozzle. The pressure is measured using a high precision MEMS Pressure Sensor & displayed in Labview.

6 ET13LV6

Experiential Learning of Digital Communication Using LabVIEW

DESCRIPTION

. This paper discusses the design & implementation of laboratories and course projects using Labview in instrumentation course. Pedagogical challenge is to enhance students’ learning of digital communication using LabVIEW.

7 ET13L Data Acquisition and Realization of

V7 Communication Transmission Based on Labview

DESCRIPTION

Through the Internet we can make the virtual experiments platform published on the web, sharing resources and avoid duplication of equipment purchased and waste of resources. A lot of data acquisition and wireless communication framework was developed based on graphic programming platform of Labview.

8 ET13LV8

Novel Design Solutions for Remote Access, Acquire and Control of Laboratory Experiments on DC

Machines

DESCRIPTION

This paper presents the novel design techniquesto access experiments on electrical machines remotely through the Web using virtual instrumentation (VI) tools.

9 ET13LV9

LabVIEW Based Automatic Paralleling of Synchronous Generator System

DESCRIPTION

This paper describes the development & implementation of automatic paralleling of synchronous generator system using Labview platform.

10 ET13LV10

Online Control of Fuzzy Based Mine Detecting Robot Using Virtual

Instrumentation

DESCRIPTION

In the real time applications the detection andlocation of bomb is highly essential in the field of defense applications. Considering the value of human life the robot is allowed in

the field to detect the bomb.

RASPBERRY PiS.No

CODE PROJECT TITLE

1 ET13RP1

Proposal of Sensor Data Gathering with Single Board Computer

DESCRIPTION

We propose a sensor data gathering system using a single board computer for home energy management systems. This sensor system should be capable of handling 100 sensor data per second. Since a single board computer has low power consumption and low performance, it is used as the sensor data gathering server.

2 ET13RP2

Building network appliances with NanoBSD operating system on Single

Board Computers

DESCRIPTION

There is presented an overview what NanoBSD operating system is and how to use it in building powerful network appliances on Single Board Computers (SBC). The supposed audience of this paper is IT/network engineers, researchers, students, Unix/Linux or BSD fans with interest focused on building their own network appliances based on embedded computers

3 ET13RP3

Evaluation of clock synchronization methods for measurement and control

using embedded Linux SBCs

DESCRIPTION

This paper reports a study and practical evaluation of two different clock synchronization methods for distributed measurement and control nodes based on Linux Single Board Computers (SBCs) with ARM processors and communicating through a TCP/IP wide area network.

4 ET13RP4

An improved real-time surveillance system for home security system using

BeagleBoard SBC, Zigbee and FTP webserver

DESCRIPTION

A number of surveillance devices in a Zigbee protocol (IEEE 802.15.4) based wireless network are connected to a Beagle-Board Single Board Computer (SBC) based surveillance management system. Remote alerting on fire and intruder detection are the key features of the system. When smoke or intruder movement is detected, the system sends warning messages through Short Message Service (SMS) to cell phones, starts capturing real-time video for fixed duration and makes the alarm on.

INDUSTRIAL AUTOMATION & PLC

S.No

CODE

PROJECT TITLE

1 ET13iP1

Utilization of the PLC as a web server for remote monitoring the technological

process

DESCRIPTION

This paper presents a new methodology to develop remote laboratories for systems engineering and automation control courses, based on the combined use of TwinCAT, a laboratory Java server application, and Easy Java Simulations (EJS). The TwinCAT system is used to close the control loop for the selected plants by means of programmable logic controllers (PLCs) deployed in PCs with the a run-time tool.

2 ET13iP2

Remote Control Laboratory Using EJS Applets and TwinCAT Programmable

Logic Controllers

DESCRIPTION

This paper presents how it is possible to utilize PLC in the task of the Web server. Described is configuration of the PLC and its connection to the computer network. Next is described principle of creation dynamic web page and described are function for process variable data read and write.

3 ET13iP3

Development of a Low Cost Programmable Logic Controller

DESCRIPTION

The aim of this study is to develop a low cost small module (hardware card), for use in the automation of simple machines and equipments. programmable logic controller (PLC) will be part of an open platform that also contains a free software tool for programming PLC in C language & online tutorial with detailed instructions about

building & programming the system.4 ET13

iP4Optimization through artificial neural

network on a Programmable Logic Controller for a Sludge Drying Plant

DESCRIPTION

The Sludge Drying Plant (SDP) is the final processing facility of Effluent Treatment System (ETS) that produces bio-sludge cake before it is sent out for final disposal. Due to the process disturbances, mechanical and inconsistent chemical reactions, the amount dry solid is reduced tremendously.

5 ET13iP5

Programmable Logic Controller (PLC) for polymer mixing tank

DESCRIPTION

The process requires manually mixing the cationic polymer long chains with raw water to produce a product that will be sent to the sludge tank process and filter press process where the sludge will harden for disposal.

6 ET13iP6

Design and fabrication of Programmable Logic Controller Kit with

multiple output module for teaching and learning purposes

DESCRIPTION

The existing PLC trainer board comes with a casing where students have the difficulty in observing and understanding the connection between the input module, PLC controller and output modules. The development of PLC Kit has been designed and improved by increasing the number of input and output components, cost reduction and it is also user friendly.

DIGITAL IMAGE PROCESSINGS.No

CODE PROJECT TITLE

1 ET13iM1

Research on edge detection algorithm for plate image

DESCRIPTION

In view of the problems that traditional edge detection algorithms are sensitive to noise and the environment of plate scene is complex, plate image is smoothed with Gaussian filter, and by comparison of edge images from non-subsampled contour let edge detection algorithm and multi-scale wavelet edge detection algorithm, a new algorithm, pulse coupled neural network edge detection algorithm based on multi-scale wavelet transform is proposed.

2 ET13iM2

A Flexible Method For Recognizing Four-Digit Numbers On A License-Plate

In A Video Scene

DESCRIPTION

In order to realize a simple system for monitoring car movements, a flexible method was developed for recognizing four-digit numbers on a license-plate in a video scene. The method consisted of three parts; global search for finding a license plate in a scene, corner detection for removing shape deformation, and numeral character recognition. The spatial features and the spectral (color) ones were merged and processed at a time in the global search.

3 ET13iM3

An adaptive threshold edge detection method based on the law of gravity

DESCRIPTION

This algorithm make up for the traditional algorithm in the whole image only used a single threshold. Through the experimental comparison, this paper algorithm can create dynamic adaptive threshold value. The algorithm has good inhibition effect used in image with salt and pepper noise and gaussian noise. it can extract image edge efficiently.

4 ET13iM4

Facial Feature Extraction With A Depth Aam Algorithm

DESCRIPTION

The main idea of our method is to use the face detection algorithm with a Kinect camera to accurately locate human head and estimate head pose. A depth AAM algorithm is developed to locate the detailed facial features. Experimental results show that our depth AAM algorithm can effectively and accurately locale facial features from video objects in conditions of complex backgrounds and various poses.

5 ET13 iM5

An Informed Watermarking Scheme Using Hidden Markov Model In The

Wavelet Domain

DESCRIPTION

This paper presents a new informed image watermarking scheme with high robustness and simplified complexity. Simulation results demonstrate that the proposed informed watermarking algorithm has high robustness against common attacks in signal processing and shows a comparable performance to the state-of-the-art scheme with a greatly reduced arithmetic complexity.

6 ET13 iM6

A Novel Data Embedding Method Using Adaptive Pixel Pair Matching

DESCRIPTION

This paper proposes a new data-hiding method based on pixel pair matching (PPM). The basic idea of PPM is to use the values of pixel pair as a reference coordinate, and search a coordinate in the neighborhood set of this pixel pair according to a given message digit. Experimental results reveal that the proposed method not only provides better performance than those of OPAP and DE, but also is secure under the detection of some well-known steganalysis techniques.

7 ET13 iM7

TRAFFIC CONGESTION IDENTIFICATION BASED ON IMAGE PROCESSING

DESCRIPTION

This study proposes a novel approach towards traffic congestion identification based on vehicle trajectories in intelligent vehicle infrastructure co-operation system (IVICS). Considering spatial-temporal trajectories as image, this study uses self-correlation to extract propagation speed of congestion wave.

AndroidS.No. CODE PROJECT TITLE

1 ET13AN1

Energy management application for smart grids aiming at mobile device

DESCRIPTION

This paper presents methods for monitoring and controlling the energy consumption, which supported the development of an Android application (for mobile devices) to interact with a Smart Grid Network.Through this application the costumer may visualize its energy consumption data and use this information to support decisions regarding the management, control or adequacy of their consumption habits.

2 ET13AN2

Portable wireless biomedical temperature monitoring system: Architecture and implementation

DESCRIPTION

This paper demonstrates the design and implementation of a portable embedded system targeting continuous temperature monitoring with wireless interface capability. Our main motive is to provide a solution for monitoring babies', disable or elderly population body temperature and initiate immediate alarm in case of hazardous cases.

3 ET13AN3

Design and implementation of a wireless tensiometer with

smartphone interface

DESCRIPTION

The prototype has been developed to allow the final user to keep a register of its own blood pressure measurement. The application also can generate a report with the measurement data that can be sent to a doctor or to an online database historical profile keeping, which may be useful for remote diagnosis procedures.

4 ET13AN4

A Common Interface for Bluetooth-based Health Monitoring Devices

DESCRIPTION

In this project a patient temperature and heart rate are monitored and displayed in an android device. This data’s are sent and received by using a Bluetooth module

5 ET13AN5

Remote Monitoring System of ECG and Human Body Temperature

Signals

DESCRIPTION

The paper presents a remote monitoring system for electrocardiographic and temperature signals. The system consists of a hardware module for acquisition, a Bluetooth transmission module and finally a displaying module (PC or mobile devices). Information is sent via IP (GPRS or Wi-Fi) to a database

6 ET13A A Bluetooth toy car control

N6 realization by android equipment

DESCRIPTION

A remote toy car controlled by an android mobile platform with Bluetooth technology is presented in this paper. The mobile platform requests to connect with the small car then sends instructions to control it by calling the android system Bluetooth API.

7 ET13AN7

Smart home system for Disabled People via Wireless Bluetooth

DESCRIPTION

in our project work, we attempt to design the smart home system including the wireless controller via Bluetooth technology. This software application adapt in mobile phone, PDA, mobile computer using android's operating system (OS). This software application will control the electrical appliances switches wirelessly (Bluetooth).

8 ET13AN8

Bluetooth-Based Android Interactive Applications for Smart

Living

DESCRIPTION

For smart living, interactive applications are increasingly important especially on interaction of people and the environment. In this work, a Bluetooth-based mobile sensor interactive application in Android- designed &

implemented.

ARDUINO

S.No. CODE PROJECT TITLE

1 ET13AR1

Data acquisition and control using Arduino-Android platform: Smart

plug

DESCRIPTION

In this work, we propose to develop a smart plug, an energy monitoring system that provides real time update of the energy consumption at the device level. The proposed device is using an arduino microcontroller board, an ENC28J60 ethernet module, and a current transformer sensor.

2 ET13AR2

ZigBee wireless sensor network for radiation monitoring at nuclear

facilities

DESCRIPTION

This paper describes the design of a WSN that allows smart real time monitoring of radiation levels at nuclear facilities. We develop a local low cost prototype of wireless sensor node equipped with a radiation sensor. The wireless node based on ZigBee technology and Arduino platform.

3 ET13AR3

Development of an educational environment for online control of a

biped robot using MATLAB and Arduino

This paper describes the development of innovative low-cost educational platform to study and control a biped robot in

DESCRIPTIONreal-time using MATLAB and Arduino board. MATLAB was used as a control and visualization environment, while the Arduino board was utilized as a final controller for the servo motors as well as a Data Acquisition Card (DAC).

4 ET13AR4

Automatic control for laboratory sterilization process based on arduino hardware

DESCRIPTION

This System is based on Arduino Board. Arduino is an Open Hardware platform that allows a fast prototype development, Arduino microcontroller is programmed on C++. making development and tests not a difficult part of overall work.