Table saw1

Woods Machine Safety #4 Table Saw

Purpose of the Planer Rip the second Edge to width. Second edge should be the Crowned Edge Outcomes

Uniform width over the entire length of the board. This means that the Edges are parallel. Edge is Square to both Faces.

The many uses for the Table Saw

Rip Cross Cut Miter Bevel Rabbit Dado Groove Tennon Tapper

Main Parts of the Table Saw

The Guard is the most important part!

Guard Lock- Flip left or right. Do not unscrew!

Saw Blade

Throat Plate

Miter Slot

Miter Guage

Fence Rails

On/Off Swich

Blade Height Adjustment

Bevel Adjustment

Blade Height- 1/8” above the wood

Minimum Length- 12”

Margin of Safety- 6”

Keep your hand away from the blade 6” in any direction.

Common Operations Use the Fence for the 5th step, ripping the

board. Use a Miter Gauge for Cross Cutting. Always use one of these two devices to guide

your wood. Never free hand cut. Never use both at the same time. Always have a surfaced face and edge when

using the table saw to cut your wood.

Body Placement while Ripping Never stand directly behind the wood, due to

kickback Body turned toward the fence when starting the cut. Left hand should be guiding the wood, outside of the

Margin of Safety. Right hand should be feeding the board until it

reaches the edge of the table. At the edge of the table, hook the push stick on the

board if there is less than 6 inches between your blade and hand.

Body Placement while Ripping As you follow through with the cut, turn your body

toward the saw. Make sure to follow through with the cut until the

wood clears the back side of the blade. Do not reach over the blade, have the tail off person

support your wood. Tail off person should not pull on the board or stand

directly behind the board. To the side of the board is the best spot.

Body placement for Cross Cutting No Fence, use the Miter Gauge, make sure it is

square. Right arm in line with the miter slot, with your right

hand holding the handle. Your left hand is holding the wood tight against the

miter gauge and the table, always keep your left hand to the outside of the miter slot.

Flip hands for cutting in the miter slot on the right side.

Blade Facts Blade determines the size of the tool. Ours is 10” Blade turns on the arbor shaft and is held on with a

washer and nut. When standing at the front of the machine, pull the

wrench toward you to loosen the left-hand threaded nut.

When looking at the blade from the left, it spins clockwise, toward the operator.

Always have a proper throat plate in position before operating the saw.

Setting up the Guard and the Blade Disconnect power Raise blade to check for squareness. Adjust bevel wheel until the blade is square. Lower blade back down to cutting position, 1/8”

above the wood. Measure between the inside of the blade tooth and

the fence to adjust the width accurately. Make sure the fence is locked before starting the

machine. When ripping make sure that the longer side of the

wood against the fence. Stability is the most important part!

Kickback Causes Letting go of the wood, always hang on to the

wood firmly. Allowing the wood to not be tight against the

fence and the table. Debris stuck between the fence and board or

between the table and board. Feeding the wood to quickly.

Offbearer Out of the Margin of Safety Push stick or pencil pointing away from the blade. Never pull on the wood just support it, keeping it level with

the table. Stay behind the fence to the side to protect your body. Make sure that the wood stays in contact with the table and

the fence. Hold on to the body of the board and the scrap piece, at the

same time make sure that the kerf stays open so that it does not pinch the blade.

Do not hand the board over the blade, place it behind the fence for the operator.

Do not reach in for any scrap wood while the blade is moving.

Table Saw Wrap-Up Move left hand to the edge of the table once

the push stick is on the board. This is for safety and stability.

Stop moving the board any time you reposition your hands or body.

Make sure the blade is stopped and lowered before leaving the machine.

Clean up debris and tools when you are done.

Table saw1

Education

MONDAY CHRISTMAS SEATING PLAN · Table 1 Table 1 1 Table 9 Table 5 Table 3 Table 7 Table 1 5 Table 1 3 Table 10 Table 1 6 Table 1 4 Table 12 Table 2 Table 8 Table 6 Table 4 MONDAY

Appendix F: Health Assessment and Histopathologic Analyses ... · Table l. Table 2. Table 3. Table 4. Table 5. Table 6. Table 7. Table 8. Table 9. Table 10. ... Historic Bridge hepatosomatic

web.iima.ac.inTable 14: Table 15: Table 16: Table 17: Table 18: Table 19 Table 20: Table 21. Table 22: Table 23: Table 24. Table 25: ... PGPM 2011 Final Placements Report . · 2012-2-16

TABLE - I - Air Indiaairindia.com/Images/pdf/WebFare.pdf · TABLE I TABLE II TABLE III TABLE IV TABLE V TABLE VI TABLE - I ROUTE 90 Days Advance Purchase 60 Days Purchase 15 Days

TABLE - I - Welcome to Air Indiaairindia.in/Images/pdf/WebFare.pdf · TABLE I TABLE II TABLE III TABLE IV TABLE V TABLE VI TABLE - I ROUTE 90 Days Advance Purchase 60 Days Purchase

MASTER OF SCIENCE DAIRY SCIENCE APPROVED: APPROVED · Table 1. Table 2. Table ). Table 4. Table Table 6. Table 7. Table S. -3-TABLES Average Total and Daily Weight Gains of Experimental

Cd) - moh.govt.nz · Air Ambulance Network List of Tables Table 11 Table 5 Table 6 Table 7 Table 8 Table 9 Table 10 Table 1 Table 2 Table 3 Table 4 Regional Control Rooms Illustrating

Supplementary table 1. Supplementary table 2 Supplementary table 3

Table Number Table Namefiles.hawaii.gov/dbedt/economic/databook/db2018/section13.pdf · Table Number Table Name (Click on the table number to go to corresponding table) Narrative

As Table Table

SOFT SEATING - Nowy Styl€¦ · Club 43 Club SQ 43 Classic table 45 Dallas table 45 Studio table 45 Concerto table 46 Hexa table 46 Hexa Wall table 46 Sand table 47 Hello! table

€¦ · XLS file · Web view · 2014-02-14Module2 Module1 Table 9 Table 8b Table 8a Table 7 Table 6 Table 5c Table 5b Table 5a Table 4 Table 3c Table 3b Table 3a Table 2 ... qtr2

DOCUMNT RESUME - ERIC · LIST OF TABLES' Table IA Table 3A. Table 3B Table 3C Table 3D Table 4A Table 7A Table 7B. School Facility Needs -4 Projected Enrollments USD 259. 1971 - 1971-76,

List2003 (2… · XLS file · Web view · 2012-03-14Table 163 Table 162 Table 161 Table 160 Table 159 Table 158 Table 157 Table 156 Table 155 Table 154 Table 153 Table 152 Table

Phage display screening of therapeutic peptide for cancer … · Phage display screening of therapeutic peptide for cancer targeting and therapy Phei Er Saw1, Er-Wei Song1,2& 1 Guangdong

Vacuum Table Specification - aeronautauto.com€¦ · Aeronaut Vacuum Table Specification 2005 Page 4 Vacuum Table Configurations Vacuum Table Configurations Table length Aeronaut

May 10, 2005 - Board of Supervisors Agenda Item fileClick Here to Return to Agenda Appendix A- Table 1 Table 1A Table 2 Table 2A Table 2B Table 3 Table 4 Table 5 CDBG Consortium Consolidated

$30.00 U.S. table table - gibbssmithcovers.comgibbssmithcovers.com/Brazilian Table Eblad.pdf · table the brazilian table table the Yara castro roBerts richard roBerts Yara castro

3D Model - decomo.be · Title: 3d saw1 Subject: Allplan Print Preview Created Date: 10/28/2009 2:05:52 PM

GENERAL GOVERNMENT DATA - European Commission...TABLE 8A ITALY 42 TABLE 8B ITALY 43 TABLE 8C ITALY 44 TABLE 8D ITALY 45 TABLE 9A CYPRUS 46 TABLE 9B CYPRUS 47 TABLE 9C CYPRUS 48 TABLE