Tools You Will Need: 3/16” Drill (preferably 6” length or

How to install the Fridge-Fix refrigerator fan into the Norcold 1200 series. Tools You Will Need: •3/16” Drill (preferably 6” length or longer) •Phillips #2 Screwdriver •Pliers •Glass Cleaner/Paper Towels

This set of instructions will walk you through how to install the Fridge-Fix by adding a small hole for the power wire. The hole is 3/16” in size, and does not affect the warranty of your fridge. This is the easiest way to provide power for the Fridge-Fix. Now let’s get started!

Verify that you are installing the unit into a Norcold 1200 series fridge. The front should have a control panel similar to this.

Inside the door, you should see a label, the model number should start with 12_ _. There are many different models of the 1200 series, but all that is important is that your number starts with 12.

Now, it is time to remove the plastic rails that hold the shelves in place. There are two rails, one on either side of the fridge. There is a total of 6 Phillips #2 screws to remove. Save the screws and set the plastic rails to the side.

Removing screws from rails…

Now, remove the lens, and the two electrical connectors from the interior light

Now remove both screws from the light bracket.

Remove the shelf in front of the drip tray, and the drip tray. The drip tray has a drain hose connected to it in the back. Make sure this drain hose does NOT get pulled all the way out of the fridge.

In preparation for installing the fan unit, clean the ceiling of the fridge with a good glass cleaner. Also remove the plastic thermistor wire clip. It is no longer needed.

THOROUGHLY dry the ceiling of the fridge. For the Velcro to stick, the ceiling must be absolutely dry.

Remove the plastic films covering the Velcro. Also remove the zip ties holding the wires on the Fridge-Fix

Insert the Fridge-Fix into place. Press up from the bottom of the unit and hold the unit against the ceiling for 15 – 20 seconds. The fan body housing should be touching the cooling fins on the back of the fridge.

Press the grounding clip onto one of the cooling fins at the back of the fridge. The clips are very high quality, so you may have to press hard.

Install the NEW drip tray. Make sure the nipple on the back of the drip tray is inserted completely into the drain tube. Re-install the shelf at this time.

Now it is time to head outside to drill the hole for the power wire.

Locate the position as indicated in the photo.

Using the 3/16” drill bit, drill FROM THE REAR OF THE FRIDGE INTO THE INTERIOR AS SHOWN. Drilling from the rear will ensure that you to not come into contact with any other components with the drill bit by mistake. The wall of the fridge is roughly 2.5” thick, hence the need for a longer bit. You can buy an extended bit at any home improvement store.

This is the bit coming through inside the fridge. Note: with the drawers removed, there is nothing to hit.

Here is the bit we used from Lowes. It was 12” long, and cost around $6.

Run the wire as shown. We ran the wire behind the drip tray in this install, but it is personal preference. We also used some of the adhesive zip tie anchors pictured below. They are also available at most hardware stores..

Route the wire through the hole that was drilled, and seal with a small dab of silicone (if desired, not required). Note the zip tie anchor in this shot.

Head back outside, and now it is time to connect the power wire. The suggested 12 Volt power source is circled here. Color of wire will change with each RV manufacturer, but if it is connected to this terminal, it is 12 Volt+. Test with a voltmeter if uncertain. (NOTE THE “12VDC” LABELING)

Using the splice included with your kit, connect the Fridge-Fix power wire to the wire as shown. Depending on your install, it may be advantageous to zip tie the wire to other wires in the compartment.

Another shot of the power wire connection. Reinstall the exterior fridge access panel, you are finished outside.

Reinstall all shelves in desired locations, and then reinstall the rails.

Now, take the light bracket, and mark as shown. The desired result is to add two 3/16” mounting holes as pictured by the black dots. These new holes will allow you to mount the light on the ceiling, without interference from the fan body housing.

Drill two new holes as shown below.

Reinstall the light bracket in the ceiling with the original screws in the new screw hole locations.

Reinstall the lens, and note the clearance. If you do not wish to modify your light bracket, you can also mount the light to the screws provided on the fan body housing. (circled) If this method is selected, you may need to add “jumper” wires for additional length to hook up your light. Contact Mike @ mikeb@smartrvproducts.com if you wish to have us make some jumpers for you.

Your Fridge-Fix is now ready for use! Turn on the power switch, and enjoy!

Some tips for best results: •If the fridge is on, the fridge-fix should be on. •If you are dry camping and concerned about power usage, sporadic use will actually LOWER the consumption of propane by your refrigerator. •Don’t forget to turn off the device when storing your RV. Nobody likes a dead battery in the spring…. • The new drip tray allows for better airflow beneath the cooling fins. If your fridge is packed too tightly with food, it will disrupt this flow of air. For best results, try lightly packing the food around the drip tray. Above all, if you have any problems at all, call us at (575)513-1712, or email mikeb@smartrvproducts.com Thank you so much for your business! From our family to yours, happy camping! -Smart RV Products

Text