View
1
Download
0
Category
Preview:
Citation preview
S485EU-02 07/2007
1621 Sakazu, Kurashiki,Okayama 710-0801, Japan
Flow Chart SheetSee Instructionsfor Use
Tips&Cautions
•Mixed PANAVIA F 2.0 paste will not set up on the pad.
•Do not use hemostatic agent containing ferric sulfate.
•PANAVIA F 2.0 Opaque shade can not be light cured ; chemical cures.
•PANAVIA F 2.0 can be cured using any type of curing light(Halogen, LED and Plasma arc light).
•For easy clean up, excess cement around the margin may belight cured partialy for 2 to 3 sec, (Using conventional halogen or LEDlight) then remove excess.
•Step by step illustrations for silanating porcelain (Please refer to the back).
DUAL CURE DENTAL ADHESIVE SYSTEMTM
QX_S485EU-01-Aaa 07.7.5 3:44 PM ページ 1
OR
SE BOND PRIMER
PORCELAIN BONDACTIVATOR
LINER BOND 2VPRIMER
PORCELAIN BONDACTIVATOR
rApply mixture to restoration.qSandblast the internal surface.
tAir dry.wApply K ETCHANT GEL to cleanthe internal surface for 5 sec.Wash and dry.
eDispense one drop each of PRIMER andACTIVATOR on the mixing dish and mix.
Silane coupling treatment procedure
Mix paste A&B for 20 sec.
reference line
mark
1 2
5 6
Sandblast, wash & dry.
Gently air dry. Dispense equal amounts of pasteA&B.
Apply ALLOY PRIMER to internalsurface of precious metalrestoration.
Mix equal amounts of ED PRIMER @A&B. Apply to the tooth. Then, wait30 sec.*ED PRIMER@initiates set of cement.
3
4 H2O
1
Cem
enta
tion
ofpr
ecio
us&
sem
i-pre
ciou
sm
etal
crow
ns,P
FMcr
owns
,bri
dges
,inl
ays
and
onla
ys.
Cementation of precious & semi-precious metal crowns, PFM crowns, bridges, inlays and onlays.
DUAL CURE DENTAL ADHESIVE SYSTEMTM
30 s
Apply mixture of the paste.
Self cure material by applyingOXYGUARD @ to the margins. Then,wait 3 min.
Light cure the margins. 20sec. per surface
(Conventional halogen or LED light) 5sec. per surface
(Plasma arc or fast halogen light)
Cementation of precious & semi-precious metal crowns, PFM crowns, bridges, inlays and onlays.
DUAL CURE DENTAL ADHESIVE SYSTEMTM
Cem
entationofprecious
&sem
i-preciousm
etalcrowns,P
FMcrow
ns,bridges,inlaysand
onlays.
19-a
9-b
OR
7 8
Remove excess cement. (For easy clean up, partialylight-cure the excess cementfor 2-3 sec. with conventionalhalogen or LED light, thenremove the excess.)
3 min
Conventional halogen, LED
Plasma arc, fast halogen
20 s
5 s
reference line
mark
Mix equal amounts of ED PRIMER @A&B. Apply to the tooth. Then, wait30 sec.*ED PRIMER@initiates set of cement
Gently air dry. Dispense equal amounts of pasteA&B. Mix paste A&B for 20 sec.minimum.
Sandblasting. Apply K ETCHANT GEL (40% phosphoricacid ) to clean surface for 5 sec.Rinse and dry.
Mix equal amounts of CLEARFIL SEBOND or LINER BOND 2V Primerswith PORCELAIN BOND ACTIVATOR(Silane). Apply mixture and air dry.
1 2 3
4 5 6
Cem
enta
tio
no
fsi
lan
ated
po
rcel
ain
/co
mp
osi
tere
sto
rati
on
s
2Cementation of silanated porcelain/composite restorations
DUAL CURE DENTAL ADHESIVE SYSTEMTM
5 s
H2O
Air
30 s H2O
Apply the mixture of the paste.
Cem
entatio
no
fsilan
atedp
orcelain
/com
po
siteresto
ration
s
29-a
9-b
OR
7 8
Remove excess cement. (For easy clean up, partialylight-cure the excess cementfor 2-3 sec. with conventionalhalogen or LED light, thenremove the excess.)
Light cure the margins. 20sec. per surface
(Conventional halogen or LED light) 5sec. per surface
(Plasma arc or fast halogen light)
Self cure material by applyingOXYGUARD @ to the margins. Then,wait 3 min.
Cementation of silanated porcelain/composite restorations
DUAL CURE DENTAL ADHESIVE SYSTEMTM
Conventional halogen, LED
Plasma arc, fast halogen
20 s
5 s
3 min
reference line
mark
Mix equal amounts of ED PRIMER @A&B and apply to the tooth. Then,wait 30 sec.*ED PRIMER@initiates set of cement.
Mix paste A&B for 20 sec. Apply the mixture of the paste tothe sandblasted crown.
Gently air dry. Dispence equal amounts of pasteA&B.
1 2
4 5
H2O
Cementation of ceramic oxide restorations: PROCERA™, IN-CERAM™, CERCON™ and other zirconia prostheses.
DUAL CURE DENTAL ADHESIVE SYSTEMTM
Cem
enta
tio
no
fce
ram
ico
xid
ere
sto
rati
on
s:P
RO
CE
RA
™,
IN-C
ER
AM
™,C
ER
CO
N™
and
oth
erzi
rco
nia
pro
sth
eses
.
3
330 s
6
Remove excess cement.(For easy clean up, partialy light-cure the excess cement for 2-3 sec.with conventional halogen or LEDlight, then remove the excess.)
7-a
Light cure the margins. 20sec. per surface
(Conventional halogen or LED light) 5sec. per surface
(Plasma arc or fast halogen light)
7-b
Self cure material by applyingOXYGUARD @ to the margins. Then,wait 3 min.
Cem
entatio
no
fceram
ico
xide
restoratio
ns:
PR
OC
ER
A™
,IN
-CE
RA
M™
,CE
RC
ON
™an
do
ther
zircon
iap
rosth
eses.
3
OR
Cementation of ceramic oxide restorations: PROCERA™, IN-CERAM™, CERCON™ and other zirconia prostheses.
DUAL CURE DENTAL ADHESIVE SYSTEMTM
3 min
Conventional halogen, LED
Plasma arc, fast halogen
20 s
5 s
Apply K ETCHANT GEL (40%phosphoric acid) to the enamelsurface for 10 sec.Rinse and gently air dry.
Mix equal amounts of ED PRIMER @A&B. Apply to the tooth. Then, waitfor 30sec.*ED PRIMER@ initiates set of cement
Gentry air dry.
Hydrofluoric acid etch the veneer.If veneer is pre-etched bylaboratory go to step .
Apply K ETCHANT GEL (40%phosphoric acid) to clean theinternal surface for 5 sec.
Mix equal amounts of CLEARFIL SEBOND or LINER BOND 2V Primerswith PORCELAIN BOND ACTIVATOR(Silane). Apply mixture and air dry.
1 2 3
4 5 6 H2O
Cem
enta
tio
no
fp
orc
elai
nve
nee
rs
4
2
Cementation of porcelain veneers
DUAL CURE DENTAL ADHESIVE SYSTEMTM
10 s
H2O
Air
5 s
H2O
Air
30 s
reference line
mark
Self cure material by applyingOXYGUARD @ to the margins.Then, wait 3 min.
Light cure the margins. 20sec. per surface
(Conventional halogen or LED light) 5sec. per surface
(Plasma arc or fast halogen light)
Apply mixture of the paste directlyto silane.
Cem
entatio
no
fp
orcelain
veneers
4
OR
10-a 10-b
Dispense equal amounts of pasteA&B. Mix for 20 sec. minimum.
Remove excess cement.(For easy clean up, partialy light-cure the excess cement for 2-3 sec.with conventional halogen or LEDlight, then remove the excess.)
7 8 9Cementation of porcelain veneers
DUAL CURE DENTAL ADHESIVE SYSTEMTM
Conventional halogen, LED
Plasma arc, fast halogen
20 s
5 s 3 min
reference line
mark
Sandblast, wash&dry.
Mix equal amounts of ED PRIMER @A&B. Apply to the tooth. Then, wait30 sec.*ED PRIMER@initiates set of cement.
Gently air dry. Dispence equal amounts of pasteA&B.
Apply ALLOY PRIMER to internalsurface of precious metal restration.
3
4 5 6
Apply K ETCHANT GEL (40%phosphoric acid) to the tooth for 10sec. Rince and dry.
H2O
Cem
enta
tio
no
fp
reci
ou
sre
sto
rati
on
s(A
dh
esio
nb
rid
ges
/Mar
ylan
db
rid
ges
)
5
1 2
Cementation of precious restorations (Adhesion bridges/Maryland bridges)
DUAL CURE DENTAL ADHESIVE SYSTEMTM
10 s
H2O
Air
30 s
Cem
entatio
no
fp
reciou
sresto
ration
s(A
dh
esion
brid
ges/M
aryland
brid
ges)
5
Self cure material by applyingOXYGUARD @ to the margins. Then,wait 3 min.
Light cure the margins. 20sec. per surface
(Conventional halogen or LED light) 5sec. per surface
(Plasma arc or fast halogen light)
Apply the mixture of the paste tosandblasted metal.
OR
9-a 9-b
Mix paste A&B for 20 sec. Remove excess cement.(For easy clean up, partialy light-cure the excess cement for 2-3 sec.with conventional halogen or LEDlight, then remove the excess.)
7 8 9Cementation of precious restorations (Adhesion bridges/Maryland bridges)
DUAL CURE DENTAL ADHESIVE SYSTEMTM
Conventional halogen, LED
Plasma arc, fast halogen
20 s
5 s3 min
reference line
markH2O
Gentle air dry.Remove excess primer with paperpoints.
Dispense equal amounts of pasteA&B.
Mix paste A&B and coat posts withmixed cement.
Sandblasting. If the post is precious metal, applyALLOY PRIMER, air dry.
Mix equal amounts of ED PRIMER @A&B. Apply to coronal and post-holetooth structure. Then, wait 30 sec.*ED PRIMER@initiates set of cement.
1 2 3
4 5 6
Cem
enta
tio
no
fco
res
or
pre
fab
rica
ted
po
sts.
6Cementation of cores or prefabricated posts.
DUAL CURE DENTAL ADHESIVE SYSTEMTM
30 s
Seat posts and apply excesscement to coronal tooth structure.
Place build-up composite directlyon PANAVIA F 2.0, light or self-cure.
7 8
Cem
entatio
no
fco
reso
rp
refabricated
po
sts.
6Cementation of cores or prefabricated posts.
DUAL CURE DENTAL ADHESIVE SYSTEMTM
reference line
mark
Apply mixture of paste to the baseof the preparation.
Mix and place the amalgam. Complete the carving and removethe matrix band.
Mix equal amounts of ED PRIMER @A&B. Apply to the tooth. Then, wait30 sec.*ED PRIMER@initiates set of cement
Gently air dry. Dispense equal amounts of pasteA&B. Mix paste A&B for 20 sec.minimum.
1 2 3
4 5 6
H2O
Am
alg
amb
on
din
g
7Amalgam bonding
DUAL CURE DENTAL ADHESIVE SYSTEMTM
30 s
7 9
Remove excess cement.(For easy clean up, partialylight-cure the excess cementfor 2-3 sec. with conventionalhalogen or LED light, thenremove the excess.)
Complete the polishing.
8-a
Light cure the margins. 20sec. per surface
(Conventional halogen or LED light) 5sec. per surface
(Plasma arc or fast halogen light)
8-b
Self cure material by applyingOXYGUARD @ to the margins. Then,wait 3 min.
Am
algam
bo
nd
ing
7
OR
Amalgam bonding
DUAL CURE DENTAL ADHESIVE SYSTEMTM
Conventional halogen, LED
Plasma arc, fast halogen
20 s
5 s
3 min
Recommended