View
5
Download
0
Category
Preview:
Citation preview
Turk J Chem
(2016) 40: 588 – 601
c⃝ TUBITAK
doi:10.3906/kim-1508-51
Turkish Journal of Chemistry
http :// journa l s . tub i tak .gov . t r/chem/
Research Article
The mediatory activity of meso-tetraphenylporphyrin iron(III) complex
immobilized in Nafion film on a Pt electrode in the oxidation of 1,2- and
1,4-hydroquinones
Slawomir DOMAGALA1,∗, S lawomira SKRZYPEK1, Micha l CICHOMSKI2, Andrzej LENIART1
1Department of Inorganic and Analytical Chemistry, Faculty of Chemistry, University of Lodz, Lodz, Poland2Department of Materials Technology and Chemistry, Faculty of Chemistry, University of Lodz, Lodz, Poland
Received: 21.08.2015 • Accepted/Published Online: 01.01.2016 • Final Version: 21.06.2016
Abstract: This paper presents the results of an investigation of the properties of a modified platinum electrode with
meso-tetraphenylporphyrin iron(III) complex immobilized in Nafion film and its catalytic activity in the electrochemical
oxidation of selected hydroquinone and catechol derivatives. The redox activity of iron complexes of porphyrins was
characterized in aqueous solutions of perchloric acid by means of cyclic voltammetry and differential pulse voltammetry.
Both the increase in the anodic peak currents of the investigated compounds during oxidation on the platinum electrode
modified with meso-tetraphenylporphyrin iron(III) complex immobilized in Nafion film (FeTPhP/Nafion/Pt) and the
considerable decrease in the cathodic peak currents related to the porphyrine complexes reduction point to mediatory
activity. The increase in the oxidation currents observed during the preparative electrolyses indicates that the modified
platinum electrode, FeTPhP/Nafion/Pt, exhibits catalytic properties. The preparative electrooxidation of the investi-
gated 1,2- and 1,4-hydroquinone derivatives showed that over 90% conversion of the substrate occurs in the shortest time
on platinum modified with iron complex of porphyrin immobilized in Nafion film.
Key words: meso-Tetraphenylporphyrin iron(III) complex, nafion, hydroquinones, chemically modified electrode, redox
mediator
1. Introduction
Hydroquinones are used in a variety of applications. They can be used as reagents for photography, dyeing fur,
plastic production, and in the pharmaceutical industry.1 What is more, catechol derivatives play an important
role in mammalian metabolism and many compounds of this type are known to be secondary metabolites
of higher plants. Additionally, some antibiotics of microbial origin contain catechol substructures. Both
catechol itself and its monosubstituted derivatives (–OH, –CH3 , –OCH3 , –CHO, and –COOH) are active
against Pseudomonas and Bacillus, but not Penicillium species. Hydroxychavicol inhibits a greater number of
microorganisms, including Pseudomonas, Cladosporium, and Pythium species. Some flavonoids and catechols
play the role of antimicrobial agents2 and due to this they should attract attention for further investigation.3
Thus, it seems that there is an urgent need to develop innovative sensors based on chemically modified electrodes
to detect 1,2- and 1,4-hydroquinones, a class of neurotransmitters. This would constitute an innovative and
promising new approach to the electrochemical detection of this class of compounds. To the best of our
knowledge, this approach remains currently unexplored.
∗Correspondence: domagala@chemia.uni.lodz.pl
588
DOMAGALA et al./Turk J Chem
A glassy carbon or platinum electrode, when subjected to an appropriate pretreatment procedure, exhibits
a minimal propensity for surface fouling with products of electrode processes. The electrochemical irreversibility
means that some organic compounds, such as catechol and hydroquinone derivatives, can undergo oxidation only
at potentials considerably shifted from their standard redox potentials. Therefore, some chemically modified
electrodes with various active mediators immobilized at the electrode surface can be used for the mediated
electrooxidation of catechol and 1,4-hydroquinone derivatives in acidic solutions.4−10 The electrode materials
were mainly glassy carbon, platinum, gold, and graphite. However, in some cases the adsorbed or immobilized
mediators on the electrodes were instable.7 Regarding this immobilization of the electrocatalysts into the
electrode, an ion-exchange polymer matrix could solve this problem. One of the best solutions to this case
might be a platinum electrode coated with Nafion film that contains the immobilized catalyst.11−26 Nafion
itself is not electroactive, but may become electroactivated after its protons of –SO3H groups are replaced with
electroactive cations or complexes (Xn+):
n(–SO3H)polym. + Xn+soln. → [Xn+ (–SO−
3 )n ]polym. + nH+soln.
The immobilization of metalloporphyrins or their complexes into polymer-coated electrodes has been
developed intensively over the past years due to the fact that these materials are efficient electrocatalysts for
chemical applications.1−8 It has been shown that such chemically modified electrodes can be used as tools
in fundamental electrochemical investigations as chemical sensors and in energy-producing or electrochromic
devices, and that they can be applied for the investigation of electrocatalytical properties.4−6 Certain metallo-
porphyrins after their immobilization in a polymer film on an electrode surface can act as redox mediators for
the oxidation of organic compounds. Iron complexes of porphyrins can be effective mediators for the oxidation
of some phenol and hydroquinone derivatives.6−8 So far, the electrochemical oxidation of hydroquinones and
catechols at a platinum electrode modified with porphyrin iron complex immobilized in Nafion film has not been
studied.
The aim of this work was to investigate the mediatory activity of platinum modified with meso-
tetraphenylporphyrin iron(III) complex immobilized in Nafion film in the electrochemical oxidation processes
of 1,4-hydroquinone (1), 2,3,5,6-tetrabromo-1,4-hydroquinone (2), 2-chloro-1,4-hydroquinone (3), 2,5-di-tert-
butyl-1,4-hydroquinone (4), 2,6-dimethyl-1,4-hydroquinone (5), catechol (6), tetrabromocatechol (7), and 3,5-
di-tert-butylcatechol (8).
2. Results and discussion
2.1. Characteristics of platinum modified with meso-tetraphenylporphyrin iron(III) complex im-
mobilized in Nafion film
It has been observed27,28 that in the redox catalysis of organic compounds the normal potential of the mediator’s
redox system should be higher than the normal potentials of substrates, but in general it should be lower than
the half-wave potential of the substrate’s reduced form. It means that for the oxidation process the catalysis
can occur when the half-wave potential of the substrate’s reduced form is higher than the normal potential
of the mediator’s redox couple, and that it is in turn higher than the substrate’s normal potential. Thus, in
the given conditions the mediator (its reduced form) should undergo oxidation at a lower potential than that
of the organic compound, the substrate. However, this is not a necessary condition in chemical catalysis. In
such case, the organic compound can be more electroactive than the mediator, as it has been observed in cyclic
voltammetry measurements for the following compounds: 2,3,5,6-tetrabromo-1,4-hydroquinone (2) and 2,5-di-
589
DOMAGALA et al./Turk J Chem
tert-butyl-1,4-hydroquinone (4) (Table 1). The investigated compounds 2 and 4 exhibit lower overpotentials for
the oxidation process than the mediator, meso-tetraphenylporphyrin iron(III) complex. For that to take place,
the rate constant of the mediator’s electrooxidation process (Table 2) (its anodic regeneration) is expected to
be higher than the rate constant of electrooxidation of the organic substrate. In consequence, the catalytic
(stoichiometric) amounts of the mediator can repeatedly oxidize large amounts of the organic substrate and
yield higher amounts of product.
Table 1. The oxidation potentials (Esubstr) for the investigated substrates: 1,2 and 1,4-hydroquinones 1–8 determined
from the cyclic voltammetry measurements at a Pt electrode in a aqueous 0.1 M NaClO4 solution. (The oxidation
potential (Emed) of the applied mediator: meso-tetraphenylporphyrin iron(III) complex is 0.494 V.)
Compound 1 2 3 4 5 6 7 8Esubstr [V] 0.582 0.370 0.577 0.367 0.545 0.775 0.633 0.584
Cyclic voltammetry, differential pulse voltammetry, preparative electrooxidation, and UV/Vis measure-
ments were performed for the purpose of studying the properties of platinummodified withmeso-tetraphenylporphyrin
iron(III) complex immobilized in Nafion film.
Figure 1 shows typical voltammetry plots of meso-tetraphenylporphyrin iron(III) complex in an aqueous
0.1 M NaClO4 solution on uncoated Pt (Figure 1a) and on Pt modified withmeso-tetraphenylporphyrin iron(III)
complex immobilized in Nafion film, FeTPhP/Nafion/Pt (Figure 1b).
-1.50E-05
-1.00E-05
-5.00E-06
0.00E+00
5.00E-06
1.00E-05
1.50E-05
2.00E-05
2.50E-05
0 0.2 0.4 0.6 0.8 1 1.2 1.4
E [V]
I [A]
1000 mV/s
500 mV/s
100 mV/s
50 mV/s
25 mV/s
10 mV/s
5 mV/s
(a)
-1.50E-05
-1.00E-05
-5.00E-06
0.00E+00
5.00E-06
1.00E-05
1.50E-05
2.00E-05
2.50E-05
3.00E-05
0 0.2 0.4 0.6 0.8 1 1.2 1.4E [V]
I [A]
1000 mV/s
500 mV/s
100 mV/s
50 mV/s
25 mV/s
10 mV/s
5 mV/s
(b)
Figure 1. The voltammograms of a) 10−3 M meso-tetraphenylporphyrin iron(III) complex in a 0.1 M NaClO4
solution on Pt, v = 5–100 mV/s; b) meso-tetraphenylporphyrin iron(III) complex immobilized in Nafion coated on
Pt (FeTPhP/Nafion/Pt), v = 5–1000 mV/s; all potentials vs. SCE.
The anodic and cathodic peaks of meso-tetraphenylporphyrin iron(III) complex immobilized in Nafion
film coated on Pt (Figure 1b) are higher and better shaped as compared to the peaks for uncoated Pt in a solution
containing meso-tetraphenylporphyrin iron(III) complex (Figure 1a), which suggests that the reversibility of
meso-tetraphenylporphyrin iron(III) complex is higher in Nafion film than in the solution. The values of the
590
DOMAGALA et al./Turk J Chem
anodic and cathodic currents and the character of voltammograms remained steady even after repeated potential
scanning (20 scans), which proves that meso-tetraphenylporphyrin iron(III) complex is effectively immobilized
in Nafion film coated on platinum.
The character of the recorded current was also studied. Taking into account the dependence ipa and
ipc = f(v1/2) (Figure 2a), we determined the range within which transport of the substance to the platinum
surface occurred under the linear diffusion process. In relation to this, the CV voltammograms for different
scan rates were recorded. The linear dependence was observed within scan rates 5–100 mV/s. The dependences
of Epa and Epc on logv (Figure 2b) for meso-tetraphenylporphyrin iron(III) complex on FeTPhP/Nafion/Pt
within the scan range v = 5–100 mV/s are also linear. This could imply a linear diffusion of electroactive
species towards the electrode surface. Therefore, the apparent diffusion coefficients (Dapp) for these forms, in
the solution, were also calculated from the Randles–Sevcik equation: ip = (2.69 × 105)n3/2 A C0 v1/2 D1/2
(where n is the number of electrons, A - electrode area [cm2 ], C0 - concentration in the bulk [mol/cm3 ], v
- sweep rate [mV/s], Dapp - apparent diffusion coefficient). The dependence of Ip = f(v1/2) in the diffusion
controlled region obeys the Randles–Sevcik equation. Since the slope of this plot is linear, it can be combined
with the amount of electroactive species immobilized (obtained by coulometric integration of the voltammetric
peaks under thin-layer conditions) and the known film thickness in order to calculate the values of the apparent
diffusion coefficients (Dapp) of meso-tetraphenylporphyrin iron(III) complex within the coating film.29,30 The
Dapp values were calculated by using the following equation: Dapp = S × L/2.69 × 105× m, [cm2 s−1 ],
where S is the slope of Ip = f(v1/2) plot, L is the film thickness, and m is the number of moles of meso-
tetraphenylporphyrin iron(III) complex incorporated in the film (Table 2).
y = -4E-06x + 3E-06R2 = 0.995
y = -4E-05x + 1E-06R² = 0.999
v1/2 [(V/s) 1/2]
(a)
y = 0.036x + 0.510R² = 0.988
y = -0.034x + 0.504R² = 0.995
log v [log mV/s]
(b)
-4.00E-05
-3.00E-05
-2.00E-05
-1.00E-05
4.00E-20
1.00E-05
2.00E-05
3.00E-05
4.00E-05
5.00E-05
0 0.2 0.4 0.6 0.8 1 1.2
ipa [A]
ipc [A] 3.00E- 01
3.50E- 01
4.00E-01
4.50E-01
5.00E-01
5.50E-01
6.00E-01
6.50E-01
0 0.5 1 1.5 2 2.5 3 3.5
E [V]
Figure 2. a) The dependence of ipa and ipc on v1/2 for meso-tetraphenylporphyrin iron(III) complex using FeT-
PhP/Nafion/Pt, v = 5–1000 mV/s. b) The dependence of Epa and Epc on logv for meso-tetraphenylporphyrin iron(III)
complex on FeTPhP/Nafion/Pt, v = 5–1000 mV/s.
591
DOMAGALA et al./Turk J Chem
Table 2. The diffusion coefficients Dapp and the standard rate constants ks of the electrode processes for meso-
tetraphenylporphyrin iron(III) complex (FeTPhP) dissolved in NaClO4 solution and after immobilization in Nafion on
a platinum electrode.
Compound
Danod.1
[cm2 s–1]
Danod.2
[cm2 s–1]
Dcat.1
[cm2 s–1]
Dcat.2
[cm2 s–1]
ks anod1
[cm s–1]
ks anod2
[cm s–1]
ks cat.1
[cm s–1]
ks cat.2
[cm s–1]
H2TPhP
Solution
0.1 M
NaClO4
7.10 × 10–5 1.08 × 10–5 4.07 × 10–6 1.45 × 10–5 2.34 × 10–3 3.57 × 10–1 1.21 × 10–1 2.69 × 10–2
H2TPhP Nafion
film 5.03 × 10–8 2.11 × 10–8 2.34 × 10–9 3.41 × 10–9 3.45 × 10–4 5.19 × 10–2 4.01 × 10–2 4.12 × 10–3
FeTPhP
Solution
0.1 M
NaClO4
3.59 × 10–5 6.55 × 10–6 2.75 × 10–6 1.02 × 10–5 1.45 × 10–3 1.78 × 10–1 8.34 × 10–2 1.06 × 10–2
FeTPhP Nafion
film 3.40 × 10–8 1.26 × 10–8 1.67 × 10–9 2.31 × 10–9 1.96 × 10–4 3.78 × 10–2 3.04 × 10–2 2.79 × 10–3
According to the atomic force microscopy (AFM) measurements performed in tapping mode the thickness
of Nafion film with immobilized meso-tetraphenylporphyrin iron(III) or nonocomplexedmeso-tetraphenylporphyrin
in the covered area was 36 nm. Since the electrode area was kept constant during the low and high scan rate
measurements, the exact size of the electrode area had no influence on the Dapp estimation. The diffusion
coefficients Dapp and the standard rate constants ks of the electrode processes for meso-tetraphenylporphyrin
iron(III) complex (FeTPhP) dissolved in NaClO4 solution and after immobilization in Nafion on the platinum
electrode surface are summarized in Table 2. For the purpose of comparison of electrode behavior with the
complexed form the noncomplexed meso-tetraphenylporphyrin (H2TPhP) was also used in measurements.
As can be seen from Table 2 the diffusion coefficients Dapp and the standard rate constants ks of the
electrode processes for noncomplexed meso-tetraphenylporphyrin (H2TPhP) are lower by about three (Danod.,
Dcat.) and about one (ks anod, ks cat.) orders of magnitude after immobilization in Nafion film on the platinum
electrode surface as compared to these values if dissolved in aqueous NaClO4 solution. A similar situation is
observed for the meso-tetraphenylporphyrin iron(III) complex (FeTPhP) after immobilization in Nafion on the
platinum electrode surface and if dissolved in aqueous NaClO4 solution. Such behavior can be attributed to the
higher viscosity of the Nafion film and the electrostatic interactions occurring within the film as compared to
aqueous solutions. Moreover, lower Danod. , Dcat. , ks anod , and ks cat. values in Nafion film can suggest that the
concentration of H2TPhP and FeTPhP might be lower as a result of the morphological and structural changes
in Nafion.
2.2. Electrochemical impedance spectroscopy (EIS)
To characterize the difference in resistance of the uncoated platinum electrode and platinum electrode coated
with Nafion film containing meso-tetraphenylporphyrin iron(III) complex immobilized in it the electrochemical
impedance spectroscopy (EIS) was performed before and after electrooxidation. Figure 3 shows the EIS results
in the form of Nyquist plots. Upon the analysis of EIS measurements it can be observed that at OCP (the open
circuit potential 0.360 V) the behavior is close to that of a nonideal capacitor, but the oxidation process of Fe(II)
ions in the meso-tetraphenylporphyrin complex is clearly occurring. The spectrum shows a significant difference
in the shape: the Pt electrode gives an almost straight line and the Nafion film coated Pt electrode shows a
little rounded line with less slope, which could be evidence of charge separation at the Nafion film/Pt substrate
interface. The values of impedance increase for the Pt electrode coated with Nafion film, which might be due to
the limitations imposed on charge transfer by the polymer coating. However, for the platinum electrode coated
592
DOMAGALA et al./Turk J Chem
with Nafion film with meso-tetraphenylporphyrin iron(III) complex immobilized in it the values of impedance
decrease. Thus the results of impedance measurements show that the electrode process is much easier for
the Pt electrode with meso-tetraphenylporphyrin iron(III) complex immobilized in Nafion film as compared to
uncoated Pt and coated Pt with Nafion film only.
2.3. Stability of platinum modified with meso-tetraphenylporphyrin iron(III) complex immobi-
lized in Nafion film
The possible decrease in electrochemical activity for the FeTPhP/Nafion/Pt electrode during electrochemical
measurement was investigated before it was used for the electrocatalytic oxidation of 1,2- and 1,4-hydroquinones.
The anodic and cathodic charges, qa and qc , in consecutive potential scan cycles were calculated for this pur-
pose. It turned out that the anodic and cathodic peak currents of the meso-tetraphenylporphyrin iron(III)
complex did not decrease. Consequently, the electrochemical activity of FeTPhP/Nafion/Pt was not reduced
during successive scans, without any change in the half-wave potential, E1/2 . The next objective was to deter-
mine the electroactive surface coverage (Γ) with the meso-tetraphenylporphyrin iron(III) complex immobilized
in Nafion on platinum.
Twenty voltammetric cycles were performed for this purpose on FeTPhP/Nafion/Pt within the scan rate
range 0.01–0.10 V/s in a 0.1 M aqueous solution of NaClO4 . The value of Γ can be calculated from Faraday’s
law, Γ = Q/nFA, where Q is the charge [C] calculated by integration of the anodic peak (with rejection of the
background current), n is the number of electrons, F is Faraday’s constant, and A is the surface area of the
conducting electrode phase in cm2 . The value of surface coverage Γ within the scan rate range 0.01–0.10 V/s
was linear, which confirms that the meso-tetraphenylporphyrin iron(III) complex was not removed from the
electrode and did not migrate into an aqueous solution after repeated scanning (Figure 4).
2.4. Mediatory activity of meso-tetraphenylporphyrin iron(III) complex immobilized in Nafion
film coated on platinum
2.4.1. Cyclic voltammetry and differential pulse voltammetry measurements
The following measurements were taken in order to investigate the mediatory properties of the meso-tetraphen-
ylporphyrin iron(III) complex: cyclic voltammetry (Figures 5a, 5b, and 6) and differential pulse voltammetry
(Figures 7 and 8) of the investigated compounds 1–8 on uncoated Pt (Figures 6 and 8, curve a), on uncoated
Pt with meso-tetraphenylporphyrin iron(III) complex dissolved in a 0.1 M aqueous solution of NaClO4 (Pt
+ TPhP) (Figures 6 and 8, curve b), and on Pt coated with meso-tetraphenylporphyrin iron(III) complex
immobilized in Nafion film (FeTPhP/Nafion/Pt) (Figures 6 and 8, curve c).
On the cyclic voltammograms the peak related to the oxidation of tetrabromocatechol appeared at Ea
= 0.611 V (Figures 6 and 8). The best results were obtained for the modified electrode, i.e. with meso-
tetraphenylporphyrin iron(III) complex immobilized in Nafion film coated on Pt (Figures 6 and 8, curve c).
In this case, the currents of anodic oxidation were higher compared to the unmodified Pt electrode. The
considerable increase in the values of the anodic and cathodic currents, as well as the decrease in ∆Ep within
the range 5–11 mV (Table 3) observed on the voltammograms of the investigated compounds 1–8 performed
on FeTPhP/Nafion/Pt points to increased activity of the mediator. On the other hand, the diminution of
the cathodic current related to reduction of meso-tetraphenylporphyrin iron(III) on FeTPhP/Nafion/Pt in
the case when the organic compound is present in the solution confirms the mediatory activity of the meso-
593
DOMAGALA et al./Turk J Chem
tetraphenylporphyrin iron(III) complex in the electrooxidation of the investigated hydroquinones and catechols
1–8.
0.00E+00
5.00E+01
1.00E+02
1.50E+02
2.00E+02
2.50E+02
3.00E+02
3.50E+02
4.00E+02
0 5 10 15 20n scans
Γx 10
-10
[mo
l/cm
2]
100 V/s
50 mV/s
25 mV/s
10 mV/s5 mV/s
Figure 3. Electrochemical impedance spectra –
Nyquist’ plots of: Pt electrode, Nafion film on Pt
electrode (Nafion/Pt) and Nafion film with meso-
tetraphenylporphyrin iron(III) complex immobilized in it
coated on Pt (FeTPhP/Nafion/Pt), all recorded in 0.1 M
aqueous solution of NaClO4 .
Figure 4. The electroactive surface coverage (Γ) on mod-
ified Pt with meso-tetraphenylporphyrin iron(III) complex
immobilized in Nafion film (FeTPhP/Nafion/Pt) after im-
mersion in a 0.1 M NaClO4 solution, the scan rate range:
5–100 mV/s.
-4.00E- 06
-2.00E- 06
0.00E+00
2.00E- 06
4.00E- 06
6.00E- 06
8.00E- 06
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9
1
2
3
4
i [A]
E [V](a)
-6.00E- 06
-4.00E- 06
-2.00E- 06
0.00E+00
2.00E -06
4.00E -06
6.00E -06
0 0.2 0.4 0.6 0.8 1 1.2
5
6
7
8
i [A]
E [V](b)
Figure 5. The cyclic voltammograms: a) of 1–4 (4.0 × 10−3 M) and b) 5 and 6 (4.0 × 10−3 M) in 0.1 M NaClO4
on uncoated Pt, v = 50 mV/s, I cycle, v = 50 mV/s, I cycle; all potentials vs. SCE, T = 298 K.
Furthermore, the simultaneous electrochemical behavior of 1,4- and 1,2-hydroquinones 1–8 at the Pt elec-
trode modified with the meso-tetraphenylporphyrin iron(III) complex immobilized in Nafion film was studied
by means of cyclic voltammetry and differential pulse voltammetry. At the beginning of the study the concen-
tration of investigated 1,2- and 1,4-hydroquinones 1–8 in the voltammetric cell was equal to 5.0 × 10−3 M and
594
DOMAGALA et al./Turk J Chem
-1.00E-05
-8.00E-06
-6.00E-06
-4.00E-06
-2.00E-06
0.00E+00
2.00E-06
4.00E-06
6.00E-06
8.00E-06
1.00E-05
-0.2 0 0.2 0.4 0.6 0.8 1E [V]
i [A]
abc
0.00E+00
2.00E-06
4.00E-06
6.00E-06
8.00E-06
1.00E-05
1.20E-05
0 0.2 0.4 0.6 0.8 1 1.2
12345678
i [A]
E [V]
Figure 6. The cyclic voltammograms of a) tetrabromo-
catechol (4.0 × 10−3 M) in a 0.1 M NaClO4 on un-
coated Pt, v = 50 mV/s, I cycle, b) tetrabromocate-
chol (4.0 × 10−3 M) in a 0.1 M NaClO4 on uncoated
Pt with meso-tetraphenylporphyrin iron(III) complex (4.0
× 10−3 M) in the solution (Pt), v = 50 mV/s, I cy-
cle, c) tetrabromocatechol (4.0 × 10−3 M) in 0.1 M
NaClO4 on modified Pt coated with Nafion film contain-
ing meso-tetraphenylporphyrin iron(III) complex immobi-
lized in (FeTPhP/Nafion/Pt), v = 50 mV/s, I cycle; all
potentials vs. SCE, T = 298 K.
Figure 7. Differential pulse voltammograms of 1–8 (4.0
× 10−3 M) in a 0.1 M NaClO4 on uncoated Pt, v = 50
mV/s, I cycle, v = 50 mV/s, I cycle; all potentials vs.
SCE, T = 298 K.
0.00E+00
5.00E-07
1.00E-06
1.50E-06
2.00E-06
2.50E-06
3.00E-06
3.50E-06
0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1
i [A]
E [V]
c
b
a
Figure 8. Differential pulse voltammograms of a) tetrabromocatechol (4.0 × 10−3 M) in a 0.1 M NaClO4 on uncoated
Pt, v = 50 mV/s, I cycle, b) tetrabromocatechol (4.0 × 10−3 M) in a 0.1 M NaClO4 on uncoated Pt with meso-
tetraphenylporphyrin iron(III) complex (4.0 × 10−3 M) in the solution (Pt), v = 50 mV/s, I cycle, c) tetrabromocatechol
(4.0 × 10−3 M) in 0.1 M NaClO4 on modified Pt coated with Nafion film containing meso-tetraphenylporphyrin iron(III)
complex immobilized in (FeTPhP/Nafion/Pt), v = 50 mV/s, I cycle; all potentials vs. SCE, T = 298 K.
then it had been changed according to the ratios 0.01, 0.10, 0.50, 1.00, 5.00, and 10.00 during the determination.
It was observed that when the concentration of 1,4- and 1,2-hydroquinones was equal and the separation of
oxidation potentials of these compounds was less than 0.070 V then the identification of the compounds was
595
DOMAGALA et al./Turk J Chem
difficult or unlikely. In the case of the equimolar mixture of 1, 3, 5, 8 or mixture of 2 and 4, or mixture of 7
and 8 overlapping of the oxidation peaks at the voltammograms occurred. When the separation of oxidation
potentials of these compounds in the equimolar mixture was higher than 0.070 V overlapping of the peaks did
not occur and the simultaneous electrochemical determination of 1,4- and 1,2-hydroquinones at the modified Pt
electrode was possible. Furthermore, in the case as the concentration ratios of all investigated hydroquinones
1–8 were of 0.01 or 0.10 the presence of the compound in a smaller amount had no effect on the recorded
oxidation peak current of the other compound.
Table 3. The results for the electrooxidation of the investigated 1,2- and 1,4-hydroquinones 1–8. The concentration of
1–8 was 5 × 10−3 M in an aqueous 0.1 M NaClO4 solution, on uncoated Pt at Esubstr. (1 0.582 V, 2 0.370 V, 3 0.577
V, 4 0.367 V, 5 0.545 V, 6 0.775 V, 7 0.633 V, 8 0.584 V) on uncoated Pt with meso-tetraphenylporphyrin iron(III)
complex (10−3 M) dissolved in a solution of aqueous 0.1 M NaClO4 (Pt + TPhP in the solution) at Emed (0.494 V),
and on Pt coated with Nafion film with immobilized meso-tetraphenylporphyrin iron(III) complex (FeTPhP/Nafion/Pt)
at Emed , all potentials are given vs. SCE.
Compound Electrode
Electro-
oxidation
time [min]
Dia [μA] vs on
Pt at Esubstr.
DEp
[mV]
Final products and yields
(for 100% of conversion)
1
Pt at Esubstr. 55 - - 1,4-benzoquinone 54%
Pt + FeTPhP in a solution at Emed 43 2.18 (1.8×) 0 1,4-benzoquinone 72%
Pt/Nafion/FeTPhP at Emed 30 2.53 (2×) 5 1,4-benzoquinone 87%
2
Pt at Esubstr 60 - - 2,3,5,6-tetrabromo-1,4-benzoquinone 55%
Pt + FeTPhP in a solution at Emed 48 1.93 (1.5×) 0 2,3,5,6-tetrabromo-1,4-benzoquinone 73%
Pt/Nafion/FeTPhP at Emed 32 2.32 (1.9×) 6 2,3,5,6-tetrabromo-1,4-benzoquinone 91%
3
Pt at Esubstr 78 - - 2-chloro-1,4-benzoquinone 48%
Pt + FeTPhP in a solution at Emed 55 2.39 (1.9×) 0 2-chloro-1,4-benzoquinone 72%
Pt/Nafion/FeTPhP at Emed 41 2.43 (2.1×) 9 2-chloro-1,4-benzoquinone 92%
4
Pt at Esubstr 56 - - 2,5-di-tert-butyl-1,4-benzoquinone 51%
Pt + FeTPhP in a solution at Emed 43 2.18 (1.7×) 0 2,5-di-tert-butyl-1,4-benzoquinone 73%
Pt/Nafion/FeTPhP at Emed 30 2.53 (1.8×) 5 2,5-di-tert-butyl-1,4-benzoquinone 91%
5
Pt at Esubstr 46 - - 2,6-dimethyl-1,4-benzoquinone 47%
Pt + FeTPhP in a solution at Emed 44 2.45 (1.9×) 0 2,6-dimethyl-1,4-benzoquinone 72%
Pt/Nafion/FeTPhP at Emed 33 2.78 (2.3×) 6 2,6-dimethyl-1,4-benzoquinone 94%
6
Pt at Esubstr 52 - - 1,2-benzoquinone 64%
Pt + FeTPhP in a solution at Emed 40 2.18 (1.9×) 0 1,2-benzoquinone 72%
Pt/Nafion/FeTPhP at Emed 31 2.53 (2.1×) 8 1,2-benzoquinone 93%
7
Pt at Esubstr 62 - - 3,4,5,6-tetrabromo-1,2-benzoquinone 55%
Pt + FeTPhP in a solution at Emed 45 2.63 (1.9×) 0 3,4,5,6-tetrabromo-1,2-benzoquinone 73%
Pt/Nafion/FeTPhP at Emed 31 3.19 (2.1×) 9 3,4,5,6-tetrabromo-1,2-benzoquinone 90%
8
Pt at Esubstr 58 - - 3,5-di-tert-butyl-1,2-benzoquinone 48%
Pt + FeTPhP in a solution at Emed 53 2.12 (1.5×) 0 3,5-di-tert-butyl-1,2-benzoquinone 72%
Pt/Nafion/FeTPhP at Emed 39 2.64 (1.9×) 11 3,5-di-tert-butyl-1,2-benzoquinone 93%
596
DOMAGALA et al./Turk J Chem
2.4.2. Scanning electron microscopy (SEM) measurements
In order to determine the difference in surface morphology before and after immobilization of meso-tetraphenyl-
porphyrin iron(III) complex in Nafion film on the platinum electrode SEM measurements were performed. The
SEM images of the investigated electrodes are shown in Figure 9. Figure 9a shows the surface of the uncoated
Pt electrode. The Pt electrode after coating with Nafion film is shown in Figure 9b and the Pt electrode
coated with Nafion film containing meso-tetraphenylporphyrin iron(III) complex immobilized in it is presented
in Figure 9c. The Nafion film forms a smooth layer on the platinum surface. In contrast, Nafion film with meso-
tetraphenylporphyrin iron(III) complex immobilized in it contains numerous crystalline structures of different
sizes and shapes. The structures belongs to the crystal conglomerates of themeso-tetraphenylporphyrin iron(III)
complex. These structures remain unchanged after mediatory electroreduction processes of the investigated
compounds 1–8.
Figure 9. Scanning microscopy images of a) uncoated Pt electrode surface; b) Pt electrode surface after coating with
Nafion film; c) Pt electrode surface coated with Nafion film containing meso-tetraphenylporphyrin iron(III) complex
immobilized in it.
2.4.3. Electrooxidation of 1,2- and 1,4-hydroquinones 1–8 with controlled potential
Electrooxidation with controlled potential of the investigated compounds 1–8 was carried out in order to in-
vestigate the mediatory properties of meso-tetraphenylporphyrin iron(III) complex. The electrooxidation of
1–8 on uncoated Pt was done at potential of oxidation of a given substrate Esubstr. . The electrooxidation of
1–8 on uncoated Pt with meso-tetraphenylporphyrin iron(III) complex dissolved in solution (Pt + TPhP) was
done at potential of oxidation of the mediator (i.e. meso-tetraphenylporphyrin iron(III) complex), Emed. . The
electrooxidation of 1–8 on Pt coated with Nafion film with meso-tetraphenylporphyrin iron(III) complex immo-
bilized in (FeTPhP/Nafion/Pt) was also done at potential of oxidation of the mediator, Emed. . As a result, 1,2-
and 1,4-benzoquinones were respectively obtained as the final products of the relevant electrooxidation processes
(Table 3). The best results were observed for Pt coated with Nafion film containing meso-tetraphenylporphyrin
iron(III) complex immobilized in (FeTPhP/Nafion/Pt). As compared to uncoated Pt, the shortest electrooxi-
dation times and the highest yields were observed using the FeTPhP/Nafion/Pt modified electrode (Table 3).
The longest electrolysis time was observed when the oxidation was carried out at the uncoated Pt and without
meso-tetraphenylporphyrin iron(III) complex in the solution.
597
DOMAGALA et al./Turk J Chem
The above observations were confirmed by the UV-VIS spectra of the electrooxidized 1,2- and 1,4-
hydroquinone solutions (10−2 M). An increase in absorbance values was observed for solutions of hydroquinones
electrooxidized on Pt coated with Nafion film containing immobilized meso-tetraphenylporphyrin iron(III)
complex (FeTPhP/Nafion/Pt) as compared to uncoated Pt and with meso-tetraphenylporphyrin iron(III)
complex present in the solution (Figure 10). Cyclic voltammetry measurements were also performed in order
to check the possibility of an electroanalytical determination of 1,2- and 1,4-hydroquinone derivatives 1–8 with
use of the anodic current peak at the Esubstr potentials.
It was discovered that in the mediated electrooxidation the peak current of the investigated compounds
at the surface of the Pt electrode modified with meso-tetraphenylporphyrin iron(III) complex immobilized in
Nafion film (FeTPhP/Nafion/Pt) was linearly dependent and proportional to the concentration of the substrate
within the range 2.0 × 10−5 –8.0 × 10−3 M. In all cases the detection limit was 2.0 × 10−5 M (Figure 11).
0
0.5
1
1.5
220 270 320 370 420 470 520
A
λ [nm]
e
d
c
b
a
R² = 0.998
R² = 0.999
R² = 0.998
R² = 0.999
R² = 0.997
R² = 0.994
R² = 0.996
R² = 0.966
0.00E+00
2.00E-06
4.00E-06
6.00E-06
8.00E-06
1.00E-05
1.20E-05
1.40E-05
1.60E-05
-2.00E-03 2.00E-18 2.00E-03 4.00E-03 6.00E-03 8.00E-03
i [A]
c [mol/L]
8
7
6
4
5
2
3
Figure 10. The UV-VIS spectra: a) of tetrabromocat-
echol (5.0 × 10−5 M) in 0.1 M NaClO4 before elec-
trooxidation, b) tetrabromocatechol (5.0 × 10−5 M) in
0.1 M NaClO4 after electrooxidation on uncoated Pt
at Emed. , c) tetrabromocatechol (5.0 × 10−5 M) in
0.1 M NaClO4 after electrooxidation on uncoated Pt at
Esubstr. , d) tetrabromocatechol (5.0 × 10−5 M) in 0.1 M
NaClO4 after electrooxidation on uncoated Pt with meso-
tetraphenylporphyrin iron(III) complex (10−3 M) in the
solution (Pt), at Emed , e) tetrabromocatechol (5.0 × 10−5
M) in 0.1 M NaClO4 after electrooxidation on Pt coated
with Nafion film containing meso-tetraphenylporphyrin
iron(III) complex immobilized in (FeTPhP/Nafion/Pt) at
Emed .
Figure 11. The plot of the electrocatalytic peak
currents from the cyclic voltammetry measurements
on modified Pt coated with Nafion film contain-
ing meso-tetraphenylporphyrin iron(III) complex im-
mobilized in FeTPhP/Nafion/Pt. (1,4-hydroquinone
(1), 2,3,5,6-tetrabromo-1,4-hydroquinone (2), 2-chloro-
1,4-hydroquinone (3), 2,5-di-tert-butyl-1,4-hydroquinone
(4), 2,6-dimethyl-1,4-hydroquinone (5), catechol (6),
tetrabromocatechol (7) and 3,5-di-tert-butylcatechol (8);
Concentration range: 2.0 × 10−5 –8.0 × 10−3 M).
2.4.4. Effect of interferences
It was studied whether the phenols and amines commonly found in waste waters from plastic production and
the pharmaceutical industry, such as 2,6-difluorophenol (a), 2,6-dichlorophenol (b), 2,3,5,6-tetrafluorophenol (c),
598
DOMAGALA et al./Turk J Chem
4−aminophenol (d), N,N-dimethylaniline (e), N,N-diethylaniline (f), N-methylaniline (g), 2,6-dimethylaniline
(h), 2,6-diethylaniline (i), 2,6-difluoroaniline (j), and 2,3,5,6-tetrafluoroaniline (k), would interfere with the
determination of 1,4- and 1,2-hydroquinones using the described method and modified electrode under the
experimental conditions (Figure 12). The investigated 1,2- and 1,4-hydroquinones concentration in the voltam-
metric cell was equal to 2.0 × 10−5 M and was fixed during the study, whereas the other phenols and amines
were present at levels ranging from 5.0 × 10−6 M to 5.0 × 10−2 M. The concentration ratios of the studied
phenols and amines to the investigated 1,2- and 1,4-hydroquinones were 0.01, 0.10, 0.50, 1.00, 5.00, and 10.00.
The presence of 2,6-dichlorophenol and 2,3,5,6-tetrafluorophenol had a major effect on the recorded peak current
(only the concentration ratio of 0.01 did not decrease the signal). 2,6-Difluorophenol caused a minor decrease
in the 1,2- and 1,4-hydroquinones signal only at 5- and 10-fold higher concentrations of the phenols and amines
mentioned above. 2,6-Dimethylaniline, 2,6-diethylaniline, 2,6-difluoroaniline, 2,3,5,6-tetrafluoroaniline, N,N-
dimethylaniline, N,N-diethylaniline, and N-methylaniline generally had no effect on 1,2- and 1,4-hydroquinones
peak current.
-1.00E -05
-8.00E -06
-6.00E -06
-4.00E -06
-2.00E -06
0.00E+00
2.00E -06
4.00E -06
6.00E -06
8.00E -06
1.00E -05
-0.2 0 0.2 0.4 0.6 0.8 1 1.2 1.4
a
7 on FeTPhP/Nafion/Pt
7 on Pt
E [V]
i [A] a)
- 1.00E-05
-8.00E-06
-6.00E-06
-4.00E-06
- 2.00E-06
0.00E+00
2.00E-06
4.00E-06
6.00E-06
8.00E-06
1.00E-05
-0.2 0 0.2 0.4 0.6 0.8 1 1.2 1.4E [V]
i [A] b)
abcd
efgh
ijk7 on FeTPhP/Nafion/Pt7 on Pt
Figure 12. The cyclic voltammograms of: a) tetrabromocatechol (4.0 × 10−3 M) and 2,6-difluorophenol (a) (4.0 ×
10−3 M), b) tetrabromocatechol (4.0 × 10−3 M) and interfering compounds a–k (4.0 × 10−3 M) in a 0.1 M NaClO4
on uncoated Pt and on modified Pt coated with Nafion film containing meso-tetraphenylporphyrin iron(III) complex
immobilized in (FeTPhP/Nafion/Pt), v = 50 mV/s, I cycle; all potentials vs. SCE, T = 298 K.
The mediatory activity ofmeso-tetraphenylporphyrin iron(III) complex immobilized in Nafion film coated
on Pt was determined. The results were compared with those obtained for uncoated Pt without meso-
tetraphenylporphyrin iron(III) complex. The character and height of the anodic and cathodic peaks were main-
tained even after several cycles, which proves that the immobilization of meso-tetraphenylporphyrin iron(III)
complex in Nafion film coated on platinum is effective and durable. The equilibrium indicating the constant
amount of meso-tetraphenylporphyrin iron(III) complex immobilized in Nafion film coated on platinum during
voltammetry measurements in a 0.1 M aqueous solution of NaClO4 was achieved after the second cycle. The
corresponding 1,2- and 1,4-benzenoquinones are the main final products of the electrochemical oxidation of
the investigated 1,4-hydroquinones and catechols 1–8 on Pt modified with meso-tetraphenylporphyrin iron(III)
complex immobilized in Nafion film. The immobilization of meso-tetraphenylporphyrin iron(III) complex in
Nafion film coated on Pt results in an increase in the oxidation peak currents of the investigated compounds
and a considerable decrease or even absence of the cathodic reduction peak of porphyrin complex, as the pro-
cess is performed at the potential of the mediator oxidation, in comparison to the same process on uncoated Pt
599
DOMAGALA et al./Turk J Chem
without porphyrin complex. The results point to the enhancement of the process yield in the presence of meso-
tetraphenylporphyrin iron(III) complex. The preparative electrooxidation for the investigated compounds 1–8
shows a substantial decrease in the duration of the process when meso-tetraphenylporphyrin iron(III) complex
is immobilized in Nafion film coated on Pt or is dissolved in a solution containing
1,4-hydroquinones and catechols 1–8. This is accompanied by an increase in the absorption band heights
in the UV-Vis spectra (Figure 10) as the oxidation process is performed on platinum modified with meso-
tetraphenylporphyrin iron(III) complex immobilized in Nafion film. Finally, the process of 1,2- and 1,4-
hydroquinones mediated electrooxidation on FeTPhP/Nafion/Pt was used for testing their possible qualitative
determination in aqueous solutions, and a linear dependence of anodic current vs. concentration was obtained
within the range of 2.0 × 10−5–8.0 × 10−3 M with a correlation coefficient of 0.9996 and a detection limit of
2.0 × 10−5 M.
3. Experimental
The cyclic voltammetry and differential pulse voltammetry measurements were performed under an argon
atmosphere using an AUTOLAB PGSTAT 10 (Eco Chemie BV) in a three-electrode system, where the working
and modified electrode was a Pt disc (ϕ =2 mm, area 0.0314 cm2), the reference electrode was saturated
calomel electrode (SCE), and the counter electrode was a cylindrical platinum gauze (5.0 cm2). The preparative
electrooxidation was performed in potentiostatic conditions also in the three-electrode system, but this time
the Pt plate was used as the working and modified electrode (area: 1.0 cm2). A drop (4.0 µL, and 100 µL
in case of the Pt plate for preparative electrooxidation) of stock solution of Nafion 117 with dissolved meso-
tetraphenylporphyrin iron(III) complex was applied on the Pt surface using a micropipette and the solvent was
allowed to evaporate in open air. The stock solution was prepared by dissolving meso-tetraphenylporphyrin
iron(III) complex (Fluka) in 100 mL of ethanol and then 1 µL of this solution was mixed with 1 mL of
Nafion 117 (Aldrich, wt. 5%) prior to use. The resulting chemically modified electrode (FeTPhP/Nafion/Pt)
was thoroughly rinsed with triple distilled water. The electrooxidation of the investigated compounds 1–8 (0.5
mmol of each compound in a 0.1 M aqueous solution of NaClO4) was carried out under potentiostatic conditions
in a glass cell (50 mL) at 25 ◦C on uncoated Pt at the potentials of the substrate electrooxidation Esubstr.
and at the mediator electrooxidation Emed. , on uncoated Pt with meso-tetraphenylporphyrin iron(III) complex
(10−3 M) ions in a 0.1 M aqueous solution of NaClO4 (Pt + TPhP in solution) at Emed , and on Pt coated
with Nafion film containing meso-tetraphenylporphyrin iron(III) complex immobilized in FeTPhP/Nafion/Pt
at Emed (Table 1).
The final products were extracted with CH2Cl2 and CHCl3 from the electrolyte solution and then
identified by means of comparing their UV-Vis, IR, 1H NMR spectra, and melting points with literature
data. The UV-Vis spectra were performed on a SPECORD M 42, the IR spectra on a SPECORD M 80,
the 1H NMR on a VARIAN 200 MHz, and the melting points were recorded on a Mel Temp II apparatus.
The topography of the Pt electrode modified with meso-tetraphenylporphyrin iron(III) immobilized in Nafion
film (FeTPhP/Nafion/Pt) was evaluated with an atomic force microscope (SOLVER P47, NT - MDT). The
atomic force microscopy (AFM) measurements of area surface and film thickness were performed under ambient
conditions in tapping mode using a MikroMasch cantilever with radius 20 nm, stiffness 40 N/m, and resonance
frequency 170 kHz. Studies of EIS were performed by potentiostat/galvanostat Autolab PGSTAT 128N with
an FRA2 module (Metrohm Autolab B.V, Utrecht, the Netherlands). The EIS spectra were registered at the
600
DOMAGALA et al./Turk J Chem
equilibrium potential within the frequency range of 0.01 Hz to 10 kHz with signal perturbation amplitude of
10 mV. Surface morphology of the electrodes was observed by scanning electron microscope (Phenom, FEI
Company).
References
1. Mark, H. B.; Atta, N. F.; Ma, Y. L.; Petticrew, L. L.; Zimmer, H.; Shi, Y.; Lunsford, S. K.; Rubinson, J. F.; Galal,
A. Bioelectrochem. Bioenerg. 1995, 38, 229-245.
2. Rayati, S.; Zakavi, S.; Valinejad, H. Turk. J. Chem. 2014, 38, 611-616.
3. Atta, N.; Marawi, I.; Pettricrew, K.; Zimmer, H.; Mark, H. B. Jr; Galal, A. J. Electroanal. Chem. 1996, 408, 47-52.
4. Lunsford, S. K.; Choi, H.; Stinson, J.; Yeary, A.; Dionysiou, D. D. Talanta 2007, 73 172-177.
5. Karami, B.; Montazerozohori, M.; Moghadam, M.; Habibi, M. H.; Niknam, K. Turk. J. Chem 2005, 29, 539-546.
6. Maldonado, S.; Morin, S.; Stevenson, K. J. Analyst 2006, 131, 262-267.
7. Kissinger, P. T.; Heineman, W. R. Laboratory Techniques in Electroanalytical Chemistry ; Marcel Dekker Inc.: New
York, NY, USA, 1996.
8. Murray, R. W. In Electroanalytical Chemistry ; Bard, A. J., Ed. Marcel Dekker Inc.: New York, NY, USA, 1984,
pp. 21-47.
9. Merz, A. Chemically Modified Electrodes. Topics in Current Chemistry, Springer-Verlag: Berlin, Germany, 1990,
pp. 49-90.
10. Freiser, H. In Ion-Selective Electrodes in Analytical Chemistry ; Buck, R. P., Ed. Plenum Press: New York, NY,
USA, 1978, pp. 1-137.
11. Ross, J. W.; Riseman, J. H.; Krueger, J. A. Pure Appl. Chem. 1973, 36, 473-487.
12. Dubois, L. H.; Nuzzo, R. G. Annual Rev. Phys. Chem. 1992, 43, 437-463.
13. Van de Mark, M. R.; Miller, L. L. J. Am. Chem. Soc. 1978, 100, 3223-3225.
14. Merz, A.; Bard, A. J. J. Am. Chem. Soc. 1978, 100, 3222-3223.
15. Oyama, N.; Anson, F. C. J. Am. Chem. Soc. 1979, 101, 739-741.
16. Anson, F. C.; Blauch, D. N.; Saveant, J. M.; Shu, C. F. J. Am. Chem. Soc. 1980, 113, 1922-1932.
17. Rubinstein, I.; Bard, A. J. J. Am. Chem. Soc. 1980, 102, 6641-6642.
18. Rubinstein, I.; Bard, A. J. J. Am. Chem. Soc. 1981, 103, 5007-5013.
19. Langmaier, J.; Trojanek, A.; Weber J.; Samec, Z. J. Electroanal. Chem. 1999, 469, 11-17.
20. Dziegiec, J.; Domaga la, S.; Cichomski, M.; Grobelny, J. Ann. Pol. Chem. Soc. 2004, 3, 882-886.
21. Domaga la, S.; Dziegiec, J. Monatshefte fur Chemie 1997, 128, 749-757.
22. Domaga la, S.; Steglinska, V.; Dziegiec, J. Monatshefte fur Chemie 1998, 129, 761-768.
23. Syper, L. Tetrahedron Lett. 1966, 7, 4493-4498.
24. Ho, T. L. Synthesis 1973, 347-350.
25. Spotnitz, R. M.; Kreh, R. P.; Lundquist, J. T.; Press, P. J. J. Appl. Electrochem. 1990, 20, 209-215.
26. Morita, M.; Kitamura, S.; Ishikawa, M.; Matsuda, Y. Electroanalysis 1996, 8, 826-830.
27. Baizer, M.; Lund, H. In Organic Electrochemistry Simonet, J., Ed. Marcel Dekker Inc.: New York, NY, USA, 1983,
pp. 812-839.
28. Lund, H.; Hammerich, O. In Organic Electrochemistry ; Simonet, J.; Pilard, J. F., Eds. Marcel Dekker Inc.: New
York, NY, USA, 2001, pp. 1163-1170.
29. Bertoncello, P.; Ugo, P. J. Braz. Chem. Soc. 2003, 14, 517-522.
30. Domaga la, S.; Dziegiec, J.; Cichomski, M.; Grobelny, J. Polish J. Chem. 2007, 81, 1049-1061.
601
Recommended