Single Pole and 3-Way Wide View Motion Activated …...Single Pole and 3-Way Wide View Motion...

Single Pole and 3-Way Wide View Motion Activated Light ControlCat. No. IPS15, IPV15 - INDOOR USE ONLY

120VAC, 60Hz - Incandescent: 1800W-15A - Fluorescent: 1800VA-15A - Supplemental: 1/2HP - LED & CFL: 600WCompatible with incandescent lamps, magnetic fluorescent ballasts, fans, CFL and LED lamps.

INSTALLATION INSTRUCTIONSWARNINGS AND CAUTIONS:• TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT THE POWER IS OFF BEFORE WIRING!• Tobeinstalledand/orusedinaccordancewithelectricalcodesandregulations.• Toavoidoverheatingandpossibledamagetothisdeviceandotherequipment,DO NOT install to control a receptacle.• DO NOT control a load in excess of specified ratings or you may damage property, or cause injury or death.• Ifyouarenotsureaboutanypartoftheseinstructions,consultanelectrician.

WARNINGS AND CAUTIONS:• Whenusingina3-wayormoreapplicationuseappropriatematchingorcoordinatingswitchremote(s).• Cleanoutersurfacegentlywithdampclothonly.DO NOT usesoapsorcleaningliquids.• Nouserserviceablecomponents.DO NOT attempttoserviceorrepair.• UsethisdeviceWITH COPPER OR COPPER CLAD WIRE ONLY.

WIRING SENSOR:Connect wires per WIRING DIAGRAM as follows:• Green or bare copper wire in wall box to Green terminal screw.• Line Hot wall box wire to terminal screw marked "BK".• Load wall box wire to terminal screw marked "RD".• LineNeutralwallboxwiretoterminalscrewmarked"WH".• Terminalscrewmarked"3-Way"shouldhaveRedinsulationlabel

affixed.NOTE: If insulating label is not affixed to terminal screw marked "3-Way",useelectricaltapetocover.

• ProceedtoStep5.

Hot (Black)

Neutral (White)

Load

BKWH

Sensor

Black

White

RD

GreenGround

3-Way Line 120 VAC, 60Hz

Use Terminal for 3-Way Applications Only.For Single Pole Applications,Do Not Remove This Label.

BK WH

RD3-Way

4

1

3

2

Terminal Screw Marked White (WH)

Sensor

TerminalScrew marked

Red (RD)

TerminalScrew marked

Black (BK)

BrassTerminal Screw

Marked 3-Way

Terminal Label:Use Terminal for 3-Way Applications Only.For Single Pole Applications, Do Not Remove This Label.

Ground(Green Screw)

PK-93977-10-00-2A

GreenGround

Hot (Black)

Neutral (White)

YL/RD 3-WayRD

WH

RD

BK

Black

BKWH

White

Line 120VAC, 60Hz

GreenGround

(unused)

(unused)

Load

SensorVP0SR-10 Remote

2BK WH

RD3-Way

Sensor

3

5

1

4

21

4

VP0SR-10 Remote

TerminalScrew marked

Black (BK)

TerminalScrew marked

Red (RD)

Brass TerminalScrew marked

3-Way

TerminalScrew marked

White (WH)

BK

RDYL/RD

WH

3

5

Ground TerminalScrew (Green)

3-Way Wiring with ViziaTM Coordinating Remote (no LED) Application: Step 4

WIRING SENSOR:Connect wires per WIRING DIAGRAM as follows:NOTE:ThesensormustbeinstalledinawallboxthathasaLineHotconnection.NOTE:Maximumwirelengthfromsensortoremotecannotexceed300ft(90m).• GreenorbarecopperwireinwallboxtoGreenterminalscrew.• LineHot(common)wallboxwireidentified(tagged)whenremovingoldswitchto

terminal screw marked "BK".• FirstTravelerwallboxwiretoterminalscrewmarked"RD"(note wire color).• RemoveRedinsulatinglabelfromterminalscrewmarked"3-Way".• SecondTravelerwallboxwiretoterminalscrewmarked"3-Way"(note wire color).

Thistravelerfromthesensormustgototheterminalscrewontheremotemarked"YL/RD".

• Neutralwallboxwiretoterminalscrewmarked"WH".

WIRING COORDINATING REMOTE: Connect wires per WIRING DIAGRAM as follows:NOTE: "BK" and "RD" terminals on coordinating remote are unused. Tightenbothscrews.NOTE:Maximumwirelengthfromsensortoremoteis300ft(90m).• GreenorbarecopperwireinwallboxtoGreenterminalscrew.• Loadwallboxwireidentified(tagged)whenremovingoldswitchtoFirstTraveler

(note color as above).• SecondTravelerwallboxwire(note color as above) to terminal screw marked

"YL/RD".Thistravelerfromtheremotemustgototheterminalscrewonthesensormarked"3-Way".

• RemoveWhiteinsulatinglabelfromterminalscrewmarked"WH".• Neutralwallboxwiretoterminalscrewmarked"WH".• Proceed to Step 5.

TOOLS NEEDED TO INSTALL YOUR DEVICE

CHANGING THE COLOR OF YOUR DEVICE

Push down tabs per diagram, one at a time and rotate forward to release

RESETRESET

TESTTEST

1 2

0 31 2

0 3

1 2

0 3

Attach new face by inserting bottom hinge tabs, then pivot and snap the color kit to attach

Yourdevicemayincludecoloroptions.Tochangecolorofthefaceproceed as follows:

INSTALLING YOUR DEVICE

NOTE: Use check boxes when Steps are completed.√

FEATURES• Cat.No.IPS15andIPV15haveasensingareaofcoverageof

30ft.x30ft.,andasensingangleof180O (see Sensing Area Coverage figure on page 2).

• Adjustablelightandtime-delaycontrolsarelocatedonthefrontofthedevice.Seeadjustmentsettingsectiononpage2fordetails.

• LEDindicatorisusedtoalerttheuserofthestatusofthedevice.• AdjustableTimeDelaysettingfor30seconds,5minutes,15minutes

and30minutes.

DESCRIPTIONTheIPV15,whichfeaturesaManual-ONoperation,isCaliforniaTitle242005compliant.Theunitturnsoffmanuallyorinabsenceofmotionaccordingtothetimeoutselected.TheIPS15providesAutomatic-ON/OFFoperationaswellasManual-OFFwiththepushpad.Theseunitsinstallinplaceofasingle-poleor3-waywallswitchandfitinastandardwallbox.Theseunitscanbeusedforswitchingincandescentlamps,magneticfluorescent ballasts, fans, CFL and LED lamps.

LOCATION / MOUNTINGThedevicerespondstotemperaturechangesandcareshouldbetakenwhenmountingthedevice.DO NOTmountdirectlyaboveaheatsource,in a location where hot or cold drafts will blow directly on the sensor, or whereunintendedmotion(e.g.,hallwaytraffic)willbewithinsensor’sfield-of-view.

Slotted/PhillipsScrewdriver ElectricalTape PliersPencil Cutters Ruler

ONOFF

ONOFF

ONOFF

ONOFF

ONOFF

ONOFF

ONOFFONOFF

ONOFF

ONOFF

ONOFF

ONOFF

Step 1 WARNING: TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER at circuit breaker or fuse and test that power is off before wiring!

IMPORTANT:For3-Wayapplications,notethatoneofthescrewterminalsfromtheoldswitchbeingremovedwillusuallybeadifferentcolor(Black)orlabeledCommon.Tagthatwirewithelectricaltapeandidentifyasthecommon(LineorLoad)inboththesensorwallboxandremotewallbox.

Step 2 Identifying your wiring application (most common):NOTE: If the wiring in the wall box does not resemble any of these configurations, consult an electrician.

2

4

1

5

3

3-Way1. Line or Load

(See important note below)

2. Neutral3. Ground4. FirstTraveler

– note color5. SecondTraveler

– note color

2

4

3

1

Single-Pole1. Line(Hot)2. Neutral3. Ground4. Load

Preparing and connecting wires:Thisdevicecanbewiredusingsidewireterminalscrewsor backwire openings. Choose appropriate wire stripping specifications accordingly.

• Makesurethattheendsofthewiresfromthewallboxarestraight (cut if necessary).

• Removeinsulationfromeachwireinthewallboxasshown.• For Single Pole Application, go to Step 4a.• For 3-Way Wiring with ViziaTM Coordinating Remote (no LED)

Strip Gage (measure bare wire here or use gage on back of the sensor)

5/8”(1.6 cm)

Cut(if necessary)

Step 3

Side WireSide wire terminals accept #14-12 AWG solid copper wire only.

Back Wire Back wire openings use #14-12 AWG solid copper wire only.

BK

RDYL 3-Way

Single Pole Wiring Application: Step 4

A

B

LIMITED 5 YEAR WARRANTY AND EXCLUSIONSLeviton warrants to the original consumer purchaser and not for the benefit of anyone else that this product at the time of its sale by Leviton is free of defects in materials and workmanship under normal and proper use for five years from the purchase date. Leviton’s only obligation is to correct such defects by repair or replacement,at its option, if within such five year period the product is returned prepaid, with proof of purchase date, and a description of the problem to Leviton Manufacturing Co., Inc., Att: Quality Assurance Department, 201 North Service Road, Melville, New York 11747.This warranty excludes and there is disclaimed liability forlabor for removal of this product or reinstallation.This warranty is void if this product is installed improperly or in an improper environment, overloaded, misused, opened, abused, or altered in any manner, or is not used under normal operating conditions or not in accordance with any labels or instructions. There are no other or implied warranties of any kind, including merchantability and fitness for a particular purpose, but if any implied warranty is required by the applicable jurisdiction, the duration of any such implied warranty, including merchantability and fitness for a particular purpose, is limited to five years. Leviton is not liable for incidental, indirect, special, or consequential damages, including without limitation, damage to, or loss of use of, any equipment, lost sales or profits or delay or failure to perform this warranty obligation. The remedies provided herein are the exclusive remedies under this warranty, whether based on contract, tort or otherwise.

Application, go to Step 4b.• For 3-Way Wiring with IPV0R Sensor Remote or ViziaTM Matching

Remote (w/LED) Application, go to Step 4c.

•Positionallwirestoprovideroominoutletwallboxfordevice.

•Ensurethattheword"TOP"isfacingupondevicestrap.

•Partially screw in mounting screws in wall box mounting holes.

•Removethefacecoverofthesensortoexposethe adjustment dials (refer to Changing the Color of your Device on page 1).

•Settimeselectionofthesensorto30secondsforaquicktimeoutduringtesting(Refer to ADJUSTMENT SETTINGS section).

•Setthelightleveldialfullclockwise(Refer to ADJUSTMENT SETTINGS section).

•Placethefacecoverbackonthesensor.•Restorepoweratcircuitbreakerorfuse.•ForIPS15lightswillautomaticallyturnonafterpowerisapplied.•ForIPV15,pressandreleasepushpadtoturnthelightsON. NOTE: See Locator Light Status chart to confirm the operational state of

thedevice.IflightsstilldonotturnON,refertotheTROUBLESHOOTINGsection.

•Leavetheroomorfieldofviewtoallowthesensortotimeoutandshutoffthe lights due to absence of motion.

•Within30secondsofthelightstimingoutstepbackintotheroomorthefieldofviewofthesensorandthelightsshouldturnbackonautomatically.

•Ifthelightsdonotturnoff30secondsafterleavingtheroomdecreasethesensitivityofthesensor(refer to the ADJUSTMENT SETTING section).

•Ifthelightstonotturnbackonautomaticallywhenyoustepbackintotheroomincreasethesensitivityofthesensor(refer to the ADJUSTMENT SETTING section).

•Settimeselectionandlightlevel(Refer to ADJUSTMENT SETTINGS section).

•Whenthedesiredlightlevel(IPS15 only),timeselectionandsensitivitysettingsareselectedplacethefacecoverbackonthesensorandcontinue to Step 6.

Restore Power: Restore power at circuit breaker or fuse.Installation is complete.

Step 7

Device Mounting:TURN OFF POWER AT CIRCUIT BREAKER OR FUSE.

Step 6

Installation may now be completed by tightening mounting screws into wall box. Attach wallplate.

Testing your Device prior to mounting in wall box: Step 5NOTE: Dress wires with a bend as shown in diagram in order torelievestresswhenmountingdevice.

ADJUSTMENT SETTINGSNOTE: Toavoid PERMANENT DAMAGE to the unit, be careful NOT TO OVERTURN the adjustment dials when setting the Sensor.1. Withpowerrestoredandwallplateremoved,removefaceofdevicetoexpose

adjustment dials (refer to Changing the Color of your Device on page 1). Useasmallscrewdrivertoadjustthelightlevel,timeselectionandsensitivityonthedeviceasfollows (Refer to Diagram):

Light Level Adjustment (IPS15 only):•Adjustthelightleveldialclockwise.LightswillturnONinlighterconditions.•Adjustthelightleveldialcounterclockwise.LightswillturnONinlesslighting

conditions.Time Selection:•Adjustthetimeselectordialtothedesiredlengthoftimethelightsareto

remainON.LightswillremainONfrom30secondsto30minutesaftertheroomisvacated.

•AdjustthetimeselectordialclockwisetoincreasethedurationoftheONtimeupto30minutes.

•AdjustthetimeselectordialcounterclockwisetodecreasethedurationoftheONtimedownto30sec.

Sensitivity:•Increaseordecreasethesensitivityofthesensorasfollows.•Todecreasesensitivityanddetectionrange,rotatethedialcounter-clockwise.

Toincreasethesensitivityanddetectionrange,rotatethedialclockwise.Withthearrowpointingat3thesensitivityisfull.Withthearrowpointingat0,thesensitivityisreducedbyhalf.Asthedialrotatesfrom2to0,thechangeinsensitivityismadeinfinesteps.

2. Attachthefacecoverandtestthatthelightlevel,timeselectionandsensitivityaresetasdesired.Ifnot,repeatadjustmentsuntilsatisfied.

For additional information, contact Leviton’s Techline at 1-800-824-3005 or visit Leviton’s website at www.leviton.com

ThisproductiscoveredbyU.S.Pat.No.7,924,155 and corresponding foreign patents.

©2012LevitonManufacturingCo.,Inc.AllRightsIncludingTradeDressRightsReserved

TROUBLESHOOTINGLights do not switch ON - IPS15:• Motionisbeyondsensingrange,moveclosertoswitch.• Adjustthelightleveladjustmenttowardlighterordarker,dependingon

room conditions.Lights always stay ON:• ChecktimedelaysettingsandcomparetohowlongthelightsstayON.• Besurethatnomotionoccursincoverageareafortimeselected.• Checkthatswitchisnotinstallednearaheatsource(e.g.,stove,lights,

heatvents)ordetectingmotionfromanadjacentarea(e.g.,hallwaytraffic).Ifso,switchmayhavetoberelocated.

• TryloweringtheSensitivityAdjustmentControl.Rotatetheknobcounterclockwiseabout30°.Iftheproblempersists,tryreducingagain.

NOTE: DO NOT reduce so much that the sensor cannot see normal occupancy.

Lights do not turn ON with the pushpad - IPV15:• Checkthatswitchisinstalledcorrectly.• CheckthatpowerisON.• Checkthatlightbulbisfunctioning.NOTE: If problems continue, consult an electrician.

FCC COMPLIANCE STATEMENTThisdevicecomplieswithPart15oftheFCCRules.Operationissubjecttofollowingtwoconditions:(1)thisdevicemaynotcauseharmfulinterference,and(2)thisdevicemustacceptanyinterferencereceived,includinginterferencethatmaycauseundesiredoperationofthedevice.ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassBDigitalDevice,pursuanttoPart15oftheFCCRules.Theselimitsaredesignedtoprovidereasonableprotectionagainstharmfulinterferenceinaresidentialinstallation.Thisequipmentgenerates,uses,andcanradiateradiofrequencyenergyand,ifnotinstalledandusedinaccordance with the instructions, may cause harmful interference to radio communications.However,thereisnoguaranteethatinterferencewillnotoccurinaparticularinstallation.Ifthisequipmentdoescauseharmfulinterferencetoradioortelevisionreception,whichcanbedeterminedbyturningtheequipmentOFFandON,theuserisencouragedtotrytocorrect the interference by one or more of the following measures:• ReorientorrelocatethereceivingAntenna.• Increasetheseparationbetweentheequipmentandthereceiver.• Connecttheequipmentintoanoutletonacircuitdifferentfromthatto

whichthereceiverisconnected.• Consultthedealeroranexperiencedradio/tvtechnicianforhelp.FCC CAUTIONAnychangesormodificationsnotexpresslyapprovedbyLevitonManufacturingCo.,Inc.,couldvoidtheuser'sauthoritytooperatetheequipment.

LOCATOR LIGHT STATUS

LOAD IPS15 IPV15

OFF Blinking Lit

ON Blinking Blinking

Lens

Push Pad

Locator Light

Side (Vertical) Field-of-View

SENSING AREA COVERAGEField-of-View (Horizontal)

30ft9.1m

30ft9.1m

6ft1.7m

1.8m6ft

30ft9.1m

8.4m27ft

2.1m7ft

1.2m4ft

2.6m8ft

Light Level Adjustment

SensitivityAdjustment

TimeSelection

1 2

0 3

1 2

0 3

1 2

0 3

Settings0123

Time30sec5 min15 min30min

PK-93977-10-00-2A©2012LevitonMfg.Co.,Inc.

NOTE:TheOccupancysensormust be installed in a wall box that hasaLoadconnection.TheSensorremotemust be installed in a wallboxwithaLineHotconnectionandaNeutralconnection.ANeutralwiretotheremoteneedstobeaddedasshown.Ifyouareunsure about any part of these instructions, consult an electrician. NOTE: Maximum wire length from sensor to all installed remotes cannotexceed300ft(90m).

WIRING REMOTE (wall box with Line Hot connection):Connect wires per WIRING DIAGRAM as follows:•GreenorbarecopperwireinwallboxtoGreenterminalscrew.•LineHot(common)wallboxwireidentified(tagged)when

removingoldswitchandFirstTravelertosensorterminalscrewmarked "BK".

•SecondTravelerwallboxwirefromsensortoremoteterminalscrewmarked"3-Way"(note wire color).Thistravelerfromtheremotemustgototheterminalscrewonthesensormarked"3-Way".

•Neutralwallboxwiretoremoteterminalscrewmarked"WH".

WIRING SENSOR (wall box with Load connection):Connect wires per WIRING DIAGRAM as follows:•GreenorbarecopperwireinwallboxtoGreenterminalscrew.•Loadwallboxwireidentified(tagged)whenremovingoldswitchto

terminal screw marked "RD".•FirstTravelerLineHottoterminalscrewmarked"BK".•RemoveRedinsulatinglabelfromterminalscrewmarked"3-Way".•SecondTravelerwallboxwire(note color as above) to terminal

screwmarked"3-Way".Thistravelerfromthesensormustgototheterminalscrewontheremotemarked"3-Way".

•Neutralwallboxwiretoremoteterminalscrewmarked"WH".•ProceedtoStep5.

3-Way Wiring with Sensor Remote or ViziaTM Matching Remote (w/LED) Application: NOTE: IPV0R sensor remote is depicted.

AdditionalNeutral Wire

TerminalScrew marked

Black (BK)

Brass TerminalScrew marked

3-Way

BK WH

RD3-Way

35

14

2BK WH

RD3-Way

3

2

1

4

5

TerminalScrew marked

Red (RD)

TerminalScrew marked

White (WH)SensorIPV0R/VP0SR-1L Remote

GroundTerminal Screw

(Green)

Hot (Bla c k )

Neutral (White)

Sensor IPV0R/VP0SR-1L Remote

3-Way RD 3-Way

WH BK BK

Bla c k

White

Line 120 V A C , 60H z

WH

Load

Green Ground

Green Ground

C OPERATIONIPS15Auto ON: LightswillautomaticallyturnONwhenroomisoccupiedormotionisdetected.TheIPS15willswitchlightsOFFwhennomotionisdetectedinun-occupied room after set period of time.Time delay adjustment: Refer to section on Adjustment Settings.Manual ON:TheIPS15willmanuallyturn-onlightsortheloadbydepressingthepushpadonthedevice.TheIPS15canbesettoonlyturnONbythepushpad(noautomaticonoperation)byadjustingtheambientlightcontroltothe "0" position.IPV15Manual ON: TheIPV15requirestheusertomanuallyturnONlightsortheloadby depressing the push padonthedevice.Thelightsorloadwillautomaticallyturn-off when the room is left unoccupied for a set period of time.Time delay adjustment: Refer to section on Adjustment Settings.NOTE: Ina3-wayapplication,usingviziaTM matching or coordinating remotes, theremotewillonlyhavetheabilitytomanuallyswitchtheloadON,thesensorwillthentimeoutandswitchtheloadOFFoncemotionisnolongerdetected.For automatic control at both locations, use IPV0R as the remote.Locator Light LED:IPS15:LEDblinkswhenmotionisdetectedandiftheloadisONorOFF.IPV15: LEDblinkswhenmotionisdetectedandwhenloadisON.LEDwillremainilluminatedwhenloadisOFF.