SIERRA Payload Preliminary Design Review Lesli Monforton NASA ARC BAER Institute July 17, 2008

SIERRA Payload Preliminary Design

Review

Lesli Monforton

NASA ARC

BAER Institute

July 17, 2008

SIERRA NosePayloads

Primary Payload: NASA ARC; Hyperspectral – Stephen Dunagan

Piggyback Payload 1: NASA Wallops FRC; Microspectrometer – Geoff Bland

Piggyback Payload 2: University of Colorado; Laser - James Maslanik Laser

Additional Instrumentation: NASA ARC; CMIGITS III - Paul Bui

Hyperspectral Payload Stephen Dunagan

Specim ImSpector Imperx Camera Data System Data Disk

Nose Layout Notes

Upper Shelf - Vibration Isolated (Lord 150APL Series Mounts) 1/8 7075 T6

Lower Shelf - Vibration Isolated (Lord 150APL Series Mounts) 1/8 7075 T6

CM3, HMR 3000 require Hard Mounting Also directly mounted: GPS Antenna,

Microspectrometer Lenses, K&Z Pyrometers-All to Top or Bottom Skin of Nose

All Drawing do not show Fiberglass Skin & Aeromat Thickness for Clarity

Side ViewAll Instruments Shown

Lower ShelfAll Instruments Shown

Upper ShelfAll Shown

HyperspectralSide View

HyperspectralTop View-Lower Shelf

Hyperspectral Top View Upper Shelf

MicrospectrometerGeoff BlandNASA Wallops Flight Facility

USB2000 Microspectrometer USB4000 Microspectrometer CT08.85 Pyrometer CT08.K6 Pyrometer K&Z Zenith Pyrometer K&Z Nadir Pyrometer P300 0-15 PSIA Pressure Pace TRH-160 Humidity Sensor Pace PT907 Thermister

MicrospectrometerContinued

Sony VAIO Computer VGN-UX180P Sony VAIO Computer VGN-UX280P Pace XR5 Data Logger Lithium Polymer 14.8V 8000MAH Battery Lithium Polymer 11.1V 2100MAH Battery

MicrospectrometerSide View

MicrospectrometerTop View Lower Shelf

MicrospectrometerTop of NoseZenith Microspectrometer-Delrin Tower Zenith Pyrometer

MicrospectrometerTop View-Bottom (From Inside)Nadir Microspectrometer Sensor &Nadir Pyrometer

LaserJames MaslanikUniversity of Colorado

Universal Laser Sensor Data System Battery IMU 3DM-G (may share CM3 Data) GPS and Antenna (may share CM3 Data)

LaserSide View

LaserTop View Lower ShelfLaser Data & Battery mounted with Velcro

Additional Nose InstrumentsPaul BuiNASA Ames Research Center

C-MIGITS III HMR-3000 Digital Compass GPS S67-1575-14 Antenna

Additional InstrumentationSide View

Additional InstrumentationTop View Note: HMR3000 is shown though it is mounted Inside

Additional InstrumentationTop Inside

Additional InstrumentationBottom View-from Inside

Nose Modifications

Add Plywood and Fiberglass supports for Upper Shelf

Add Plywood mounts to Top Skin Cut away portion of existing plywood Lower

Shelf Add Plywood to bottom inside rear Make Fiberglass cover for existing gimbal

hole

Nose ModificationsContinued

Click Bond 8x32 & 6x32 Locking Nut Plates bonded to Plywood Shelves

All Plywood Aircraft Grade and Sealed with Epoxy

Nose Modifications Side View New Top & Upper/Lower Shelf Mounts

Nose Modifications Top View Lower Shelf Before

Nose Modifications Top View Lower Shelf After CutoutUpper Shelf & Bottom Mod’s not shown for Clarity

Nose BottomHole Glassed & Bottom Shelf Supports Added

Nose ModificationsNew Top Mounts InsideView

Nose Modifications Top View New Upper Shelf

Nose ModificationsTop View-New Bottom ¼ ShelfLower Shelf Not Shown for Clarity

Nose Modifications Front ViewForward Bulkhead & Hatch Cross Section

Nose ModificationsFront Views: New Upper Shelf; Top Mounts; CM3 Mount

Lower Shelf PlateVAIO & Microspectrometer Mounts RivetedNut Plates Riveted for the Imperx, ImSpector & Laser Mounts

Upper Shelf PlateComputer Mounting Rails Riveted to Plate

ImSpector & Imperx Mounting BracketsMachined from 6061 T6 4”x3” Stock Shown

Microspectrometer MountUSB2000 &USB4000Bent from 0.070 2024 T3 Sheet

VAIO Computer Mounts Bent from 0.070 2024 T3 Sheet Riveted to Lower Plate & VAIO secured using Velcro & Foam Spacer

Pace TRH-160 Humidity SensorMounted to front of Lower ShelfMachined from 1” 6061 T6 Bar Stock

Microspectrometer Zenith MountMachined from Delrin

Modification Additional Notes

Upper Shelf reinforced with fiberglass where its bonded to nose fiberglass shell

Old Gimbal Hole: Glassed & reinforced with Aeromat; same as existing glass work

Weight & Balance

Nose before Modification = 4.625 lbs. Modifications plus Instruments = 42.575 lbs Total Estimated Payload Nose = 47.2 lbs Estimated CG of Nose at Station 91 Rear of Nose is Station 100