View
238
Download
5
Category
Tags:
Preview:
DESCRIPTION
Samsung TXR3079 Service Alignment
Citation preview
Alignment & Adjustment
Samsung Electronics 3-1
3. Alignment & Adjustment3-1 Service Instruction 1. General Adjustment :
In general, a color TV can provide ideal visual quality by adjusting the basic settings such as the vertical size, horizontal size, focus, etc.Display a black and white picture on the screen to check if the picture is clearly displayed.If there are some 'spotted' points on the screen when displaying a black and white picture, degauss the screen using the degauss coil. If the spotted points remain, re-adjust the purity and the convergence. This completes the basic performance examination.
Notice. These adjustments and the check list are only applied to K62A chassis-applied models. Only use 110V for the measurement set. It is recommended using an insulation transformer when supplying power to
the set so as to prevent shock to the set or to yourself. These adjustment specifications have been created on the basis of the domestic K62A chassis-applied remote control
model. Some of the contents may be changed subject to the sales location and the product specifications.
2. When replacing the System Board :Since the software is loaded to the flash memory of the system board, check the version of the software after replacing the board.To check the version of the software, select Menu-Settings-Function Help-Settings and press the "Information Display" key on the remote control. The software information will then be displayed below the OSD menu.The notation of the software information : For example, T_COREAUS0_0013 refers to
"CORE BASIC MODEL USA. ver0013".Since the settings including the Channel information, Deflection, etc. are saved to the nvRAM, reconfigure these settings when replacing the System Board.
3. When replacing the Deflection Board :Tilt adjustment, focus adjustment, screen voltage setting and W/B adjustment are all required.
4. When replacing the Power Board : No adjustments required.
5. When replacing the CRT Ass'y : No adjustments required.
6. When replacing the front panel master power switch : No adjustments required.
7. When replacing the Side AV : No adjustments required.
8. When replacing the control switch : No adjustments required.
Alignment & Adjustment
3-2 Samsung Electronics
3-2 How to Access Service Mode
MENU Show all menus / Move the cursor to select an item. / Adjust the selected configuration value
1. To enter Service Mode, press the keys on the remote control according to the following sequence. (in Stand-by status)
Mute 1 8 2 Power On
When failing to enter Service Mode, repeat the procedure above.
2. The initial screen of Service Mode.
3. Functions of the Keys within Service Mode
DeflectionVideo Adjust 1Video Adjust 2Video Adjust 3Video Adjust 4Video Adjust 5OPTIONDNIE LiteANYNET PORTCHECKSUMRESET
T_COREKRX_XXXX, XXX.XX.XXXXT_COREKRX_XXX
Alignment & Adjustment
Samsung Electronics 3-3
3-3 Factory Data The underlined are items applied during the service adjustment. None of the others should be adjusted.
No Item Data Adjusted or not Remark
1 V - AMP 37 Var Vertical AMP Gain
2 V - SHIFT 27 Var Vertical AMP Posistion
3 H - AMP 39 Var Horizontal AMP Gain
4 H - SHIFT 45 Var Horizontal AMP Posistion
5 V - LIN 4 Fix Napolenon hat changed
6 UP - LIN 7 Fix Napolenon hat changed
7 LOW - LIN 4 Fix Napolenon hat changed
8 V - SC 2 Fix Napolenon hat changed
9 H - PAR 38 Var
10 UP - COR 33 Var
11 LOW - COR 33 Var
12 H - TRA 25 Var
13 BOW 33 Var
14 ANGLE 29 Var
15 V - POSITION 32 Fix
16 Up UCG 0 Fix Changes the picture distortion correction
17 Lo UCG 0 Fix Changes the picture distortion correction
18 CXA LEFT BLK 28 Fix Countermeasure against rolled-picture
19 CXA RIGHT BLK 20 Fix Countermeasure against rolled-picture
20 DVI_HD_1080i 33 Interoperability
21 DVI_HD_720p 33 Interoperability
22 DVI_HD_480i 33 Interoperability
1. Deflection
Alignment & Adjustment
3-4 Samsung Electronics
Alignment & Adjustment
Samsung Electronics 3-5
2. Video Adjust 1No Item Data Adjusted or not Remark
1 R_CUTOFF 26 Var
2 G_CUTOFF 24 Fix
3 B_CUTOFF 23 Var
4 COLOR_ONOFF 1 Fix
5 CR_OFFSET 33 Fix
6 CB_OFFSET 33 Fix
7 R_DRIVE 30 Fix
8 G_DRIVE 24 Fix
9 B_DRIVE 29 Var
10 SUB_BRIGHT 25 Var Improves the visual quality
11 SUB_CONTRAST 9 Var Improves the visual quality
12 SUB_COLOR(RF) 7 Fix Improves the visual quality
13 SUB_TINT(RF) 10 Fix Improves the visual quality
14 CTI_LEVEL 1 Fix Improves the visual quality
15 COL_AXIS 2 Fix
16 LTI_LEVEL 3 Fix Improves the visual quality
17 VSU 0 -
18 CROSSOVER-FILTER 0 -
19 MELODY_VOLUME 12 Fix
20 LTI MODE 1 Fix
21 SYSTEM 2 Fix
Alignment & Adjustment
3-6 Samsung Electronics
3. Video Adjust 2No Item Data Adjusted or not Remark
1 ABL_Mode 2 Fix
2 Gamma 2 Fix Corrects mid brightness
3 DPIC_LEVEL 3 Fix
4 DC-TRANS 3 Fix
5 ABL_TH 3 Fix Reduces the ABL response time (changes the number of corrections)
6 VM_LEVEL 2 Fix Changes the amount of the VM correction
7 VM_CORING 2 Fix Changes the amount of the VM correction
8 VM_F0 0 Fix Improves DTV sag
9 VM_LIMIT 2 Fix
10 VM_DELAY 2 Fix Improves DTV sag
11 SHIP_CD 1 Fix
12 SHIP_F0 1 Fix Improves DTV sag
13 SHIP_F1_Gain 3 Fix
14 SHIP_F1_PREOVER 3 Fix
15 AKB_TIMING 18 Fix Reduces the rolled-picture at the top screen
16 UP_UCP 2 Fix Changes the picture distortion correction
17 LO_UCP 0 Fix Changes the picture distortion correction
Alignment & Adjustment
Samsung Electronics 3-7
4. Video Adjust 3No Item DATA Adjusted or not Remark
1 Pilot Low 7 -
2 Pilot High 13 -
3 H Comp 5 Fix Improves the high-voltage regulation
4 V Comp 5 Fix Improves the high-voltage regulation
5 Pin Comp 2 Fix
6 AFC Comp 0 Fix
7 Sync Phase 0 Fix
8 Sub Color 480i 6 Fix
9 Sub Tint 480i 9 Fix
10 Sub Color 480p 9 Fix
11 Sub Tint 480p 8 Fix
12 Sub Color 720p 8 Fix
13 Sub Tint 720p 8 Fix
14 Sub Color 1080i 8 Fix
15 Sub Tint 1080p 8 Fix
16 Video Mute Time option 4 Fix
17 YPFT 3 Fix Domestic ch/up down mute time (400ms)
18 YPFG 11 Fix Improves the visual quality
19 HPLL MIN 18d Fix
20 HPLL MAX 50d Fix
21 Pixel_Shift_Time 60 Fix
22 P-ABL 0 Fix
23 Picture on Time 4.0s Fix
5. Video Adjust 4No Item DATA Adjusted or not Remark
1 YC_DELAY 3 Fix
2 YC_DELAY_AV 3 Fix
3 H-PEAK(3230) 3 Fix Improves peaking
4 480p_PR_MST9883 0x7d Fix
- Applies countermeasures against w/b difference
5 480p_PB_MST9883 0x7d Fix
6 720p_PR_MST9883 0x82 Fix
7 720p_PB_MST9883 0x81 Fix
8 1080i_PR_MST9883 0x82 Fix
9 1080i_PB_MST9883 0x81 Fix
10 Red_Gain_MST9883 0x95 Fix
11 Green_Gain_MST9883 0x95 Fix
12 Blue_Gain_MST9883 0x95 Fix
Alignment & Adjustment
3-8 Samsung Electronics
6. Video Adjust 5No Item DATA Adjusted or not Remark
1 Dynamic Dynamic Fix
2 Dynamic COOL1 -
3 Contrast 100 Fix
4 Brightness 45 Fix
5 Sharpness 75 Fix
6 Color 50 Fix
7 Tint 50 Fix
8 Standard WARM1 -
9 Contrast 80 Fix
10 Brightness 50 Fix
11 Sharpness 50 Fix
12 Color 50 Fix
13 Tint 50 Fix
14 Movie WARM2
Application of the Micom offset value required- VM Level : 1 0- Tint : 9 10- Color Temperature : Cooler 1 Warmer 2- Brightness: Step up adjustment value by +5
15 Contrast 70 Fix
16 Brightness 45 Fix
17 Sharpness 35 Fix
18 Color 50 Fix
19 Tint 50 Fix
20 Custom - -
21 Contrast 80 Fix
22 Brightness 50 Fix
23 Sharpness 50 Fix
24 Color 50 Fix
25 Tint 50 Fix
26 Initial Color COOL1 Fix 1. Korea : Cool 12. America : Warm 1
27 Cool 2 - 1. Korea : 15,000 0(H/Low:268,274)2. America : 15,000 0(H/Low:268,274)
28 RC Offset 32 Fix
29 BC Offset 34 Fix
30 RD Offset 32 Fix
31 BD Offset 35 Fix
32 Cool 1 Dynamic - 1. Korea : 13,000 0(H/Low:268,274)2. America : 13,000 0(H/Low:268,274)
33 RC Offset 32 Fix
34 BC Offset 32 Fix
35 RD Offset 32 Fix
36 BD Offset 32 Fix
Alignment & Adjustment
Samsung Electronics 3-9
No Item DATA Adjusted or not Remark
37 Normal - 1. Korea : 9,300 0 (H/Low:285,293)2. America : 9,300 0 (H/Low:285,293)
38 RC Offset 34 Fix
39 BC Offset 30 Fix
40 RD Offset 34 Fix
41 BD Offset 31 Fix
42 Warm1 Standard 1. Korea : 9,300 0 (H/Low:293,302)2. America : 7,500 0 (H/Low:293,302)
43 RC Offset 37 Fix
44 BC Offset 25 Fix
45 RD Offset 36 Fix
46 BD Offset 25 Fix
47 Warm2 Movie - 1. Korea : 6,500 6 (H/Low:285,293)2. America : 6,500 6 (H/Low:285,293)
48 RC Offset 39 Fix
49 BC Offset 20 Fix
50 RD Offset 39 Fix
51 BD Offset 20 Fix
Alignment & Adjustment
3-10 Samsung Electronics
7. OPTIONNo Item DATA Adjusted or not Remark
1 DNIe on/off 0 FixDNIe function on/off
2 DNIe DEMO off/ON 1 Fix
3 MM Slot off/on 0 Fix only 76 series
4 Auto Power off/on 0 Fix auto power on/off
5 Tect patt off/on 0 Fix service man adjust pattern
6 X-Lay off/on 1 Fix x-lay protection
7 scr size 4:3 off/on 0 Fix model inch size option
8 BBE Off/on 1 Fix sound effect on/off(must)
9 LNA off/on 1 Fix Korea(on)
10 3D-Comb off/on 1 Fix
11 HDMI off/on 1 Fix America only
12 DDC Port. off/on 1 Fix
13 Anynet off/on 0 Fix Korea only
8. DNIE LiteNo Item DATA Adjusted or not Remark
1 CE Cutoff 32 / 32 Fix Contrst Enhancement Low Limit
2 CE UPPER 196 / 196 Fix Contrst Enhancement High Limit
3 CE GainMax L 80 / 80 Fix Contrst Enhancement Low Gain
4 CE GainMax U 80 / 80 Fix Contrst Enhancement High Gain
5 DE_GAIN1X 32 Fix Improvement of horizontal high frequency characteristics
6 DE_GAIN2X 30 / 30 Fix Improvement of horizontal middle frequency characteristics
7 DE_GAIN3X 12 Fix Improvement of horizontal low frequency characteristics
8 DE_GAIN1Y 12 Fix Improves the vertical high frequency characteristic
9 DE_GAIN2Y 30 / 30 Fix Improves the vertical low frequency characteristic
10 DE_SCALE_R 68 / (100) Fix
11 DE_CORING_TH1 2 / (1) Fix Improves the input signal coring
12 DE_CORING_TH2 2 / (1) Fix Improves the input signal coring
13 DE_CORING_TH3 2 / (1) Fix Improves the input signal coring
14 NE_ALPHAL 128 / 128
15 NE_ALPHAU 128 / 128
16 CCS_CONT 153 / 153
17 CCS_BRIGHT 0 / 0
18 CTE_SCALE_ALPHA 125 / 125
Alignment & Adjustment
Samsung Electronics 3-11
9. ANYNET PORTNo Item DATA Adjusted or not Remark
1 ANYNET PORT A.NET Fix Used as a CJ20 Anynet port
10. CHECKSUMNo Item DATA Adjusted or not Remark
1 - - Change
11. RESETNo Item DATA Adjusted or not Remark
1 - - Change
# Added itemItem DATA Var/Fix
WhiteBalance
High : x : 273 3 y : 286 3 Y : 41 3Low : x : 272 3 y : 280 3 Y :1.0 0.3 White Balance (Standardization Applied)
Screen Voltage The Highest Voltage among RK, GK and BK175Vp-p-3V screen voltage
Alignment & Adjustment
3-12 Samsung Electronics
3-4 Service Adjustment3-4-1 Adjusting the Picture Size
Since the K62A chassis has the deflection settings data within the Factory Data, the picture size has to be adjusted when replacing the System Board or the Deflection Board, according to the following procedures.
1. Display the Lion pattern. 2. Press "Power Off Mute 1 8 2 Power On" using the remote control and enter Factory Mode.
4
4
5 5
4
4
5 5
3. Enter Deflection Mode. 4. Adjust the V-AMP, V-SHIFT, H-AMP and H-SHIFT items so that the width becomes 5 and the height becomes 4.
4
4
5 5
4
4
5 5
Alignment & Adjustment
Samsung Electronics 3-13
3-4-2 Adjusting the Picture Straight Lines
1. Display the Cross Hatch pattern.
2. Adjust settings other than V-AMP, V-SHIFT, H-AMP and H-SHIFT so that straight lines are displayed without curves.
7. When the adjustments are complete, display the Lion pattern and check that the picture size has not been changed.If there is no change, finish the adjustments.
3. Adjust BOW and the Angle settings so that the center linebecomes a straight line.
4. Adjust the H-Parabola and H-Trapezium settings so that the left and right lines become straight.
5. Adjust the Upper Corner and the Low Corner settings so thatthe end of the lines become straight.
6. Adjust the V-Linearity and V-SC settings so that theintervals of the horizontal lines become uniform.
Alignment & Adjustment
3-14 Samsung Electronics
3-5 Software Upgrade3-5-1 Checking the Version of the Software
1. Turn the set on and display the Menu window using the remote control.
2. Select Settings Function Help.
3. Move the cursor to ON from "ON/OFF" and press the Display key on the remote control.
4. The version of the software will be displayed at the bottom of the menu.ex)T_CORENKR1_XXX. Fed 18 2004
Alignment & Adjustment
Samsung Electronics 3-15
3-5-2 Service Download Procedure
1. Select "Power Off Mute 1 8 2 Power On"to select Service Mode.Check that the Anynet Port is set to Svc.
2. If it is not set to Svc, set it to Svc using the left and right direction keys and turn the TV set off.
3. When the TV set is turned off, connect the serial cable for download to the Svc port of the TV set and the COM port of the computer.
4. Turn the TV set on and check the screen display status. Prepare the download software, sdown.bat, and the image of thecorresponding version of the software on the computer.
Alignment & Adjustment
3-16 Samsung Electronics
Separate the serial cable onlyafter the power LED is turned off.
6. The software is automatically downloaded to the TV.
Notice: Take care when downloading the software, because if the set is turned on while writing the corresponding image data tothe flash memory, the flash memory will be damaged and has to be replaced.
5. While the TV set is on, run sdown.bat.When the percentage of the Reading File becomes 100%, turn the TV set off using the transmitter.
7. When the write operation is complete, disconnect the power cord of the TV set. When the power LED is turned off (after approximately 10 seconds), separate the serial cable from the TV and turn the TV on and check the version of the software.
Notice: If you separate the serial cable from the TV before the power LED is turned off, the COM port of the computer may be damaged. Ensure that the serial cable is not separated from the TV and the computer, until the power LED is turned off.
Alignment & Adjustment
Samsung Electronics 3-17
3-5-3 Checking the System Using HyperTerminal
1. The HyperTerminal setup procedures for using HyperTerminal through a RS-232 connection.
2. Select [Start] -> [All Programs] ->[Accessories]-> [Communications] -> [HyperTerminal]
3. In the New Connection window, enter the name of your choice (e.g.TR2), select an icon for the connection and then click theOK button.
4. In the Connect To window, configure the [Connect using] to [COM1] and click the OK button.If the computer output is set to COM2, set it to [COM2].
5. Configure the Port Settings in the COM1 Properties window as follows and then click the OK button.Bits per second 115200Data bits 8Parity None Stop bits 1Flow control None
6. Run HyperTerminal.
7. Connect the RS-232 cable to the debug port of the TV set and the COM port of the computer and run the HyperTerminalconnection icon created in the steps above.
Alignment & Adjustment
3-18 Samsung Electronics
3-6 Replacements & Calibration
3-6-1 Adjusting the Focus
Since the K62A chassis has a built-in dynamic focus circuit, take care when adjusting the focus. When the CRT PCB, FBT or CRT has been replaced, the focus has to be adjusted according to the following procedures.
1. Display the CROSS Hatch pattern.
2. Set the Screen Adjustment to "View as Standard".
3. Turn the Static Focus VR clockwise to the maximum position.(End of clockwise direction)
4. Turn the Dynamic Focus VR counter clockwise to the maximum position.(End of counter clockwise direction)
5. Slowly turn the Static Focus VR counter clockwise so that the center vertical lineis the most clearly displayed.
6. Slowly turn the Dynamic Focus VR clockwise so that the 2nd line is the most clearly displayed.
7. Check the entire screen focus and repeat steps 3 to 6, if necessary.
H
V
Static
Focus VR
Dynamic
Focus VR
H
VAfter Adjustment
H
V
1
2
3 After Adjustment
Alignment & Adjustment
Samsung Electronics 3-19
3-6-2 Adjusting the Screen Voltage
1. Select "Power Off Mute 1 8 2 Power On" to enter Service Mode.
2. Initialize all settings to the values appropriate to the corresponding model.
3. Display the Toshiba pattern.
4. Using an Oscilloscope, measure the size of RK, BK and GK to thePedestal Level.
5. Adjust the Screen VR of FEB so that the highest point of the Pedestal Level is 175V.
Screen Voltage Measurement Data
BK
RK
GK
Screen
VR
175V
Adjust Method the Screen Voltagefor Toshiba Pattern by Oscilloscope
No Item Data Required Adjustment
1 Screen Voltage The Highest Voltage among RK, GK andBK 175Vp-p-3V Screen Voltage
Alignment & Adjustment
3-20 Samsung Electronics
3-6-3 Adjusting the White Balance
1. Select "Power Off Mute 1 8 2 Power On" to enter Service Mode.
2. Initialize all settings to the values appropriate to the corresponding model.
3. Display the Toshiba pattern and adjust the White Balance using CA100 with the coordinates of the corresponding model.
4. Enter Video Adjust1 of Service Mode. Adjust Low/Light.- Adjust Sub Bright to set Y.- Adjust B Cutoff to set y.- Adjust R Cutoff to set x.
5. Enter Video Adjust1 of Service Mode. Adjust High/Light.- Adjust Sub Contrast to set Y.- Adjust B Drive to set y.- Adjust R Drive to set x.
6. Check Low/Light and readjust it if its value has been changed.
7. If you have readjusted Low/Light, readjust High/Light until the two values are identical to the coordinates of the corresponding model.
White Balance Standard Data
3-6-4 Check List for the Screen Voltage and White Balance Adjustment
1. The Screen Voltage and White Balance are connected each other, and both of them have to be configured to the correct values.
2. Adjust the White Balance after the Screen Voltage was adjusted, and check if the Screen Voltage is normal after adjusting the White Balance.
3. If the White Balance is readjusted, check the Screen Voltage again.
4. When the adjustment is finished, check the following checklist.- If there is a spot on the screen when turning the TV set off/on, adjust the Screen Voltage again.- If there is a ghost line on the screen, adjust the Screen Voltage again.
No Item Data Required Adjustment
1 WhiteBalancex:270 3 y:270 3 Y:40 3
x:270 3 y:270 3 Y:0.9 0.3 White Balance (Standardization Applied)
3. Alignment & Adjustment3-1 Service Instruction3-2 How to Access Service Mode3-3 Factory Data3-4 Service Adjustment3-4-1 Adjusting the Picture Size3-4-2 Adjusting the Picture Straight Lines
3-5 Software Upgrade3-5-1 Checking the Version of the Software3-5-2 Service Download Procedure3-5-3 Checking the System Using HyperTerminal
3-6 Replacements & Calibration3-6-1 Adjusting the Focus3-6-2 Adjusting the Screen Voltage3-6-3 Adjusting the White Balance3-6-4 Check List for the Screen Voltage and White Balance Adjustment
/ColorImageDict > /JPEG2000ColorACSImageDict > /JPEG2000ColorImageDict > /AntiAliasGrayImages false /DownsampleGrayImages true /GrayImageDownsampleType /Bicubic /GrayImageResolution 300 /GrayImageDepth -1 /GrayImageDownsampleThreshold 1.50000 /EncodeGrayImages true /GrayImageFilter /DCTEncode /AutoFilterGrayImages true /GrayImageAutoFilterStrategy /JPEG /GrayACSImageDict > /GrayImageDict > /JPEG2000GrayACSImageDict > /JPEG2000GrayImageDict > /AntiAliasMonoImages false /DownsampleMonoImages true /MonoImageDownsampleType /Bicubic /MonoImageResolution 1200 /MonoImageDepth -1 /MonoImageDownsampleThreshold 1.50000 /EncodeMonoImages true /MonoImageFilter /CCITTFaxEncode /MonoImageDict > /AllowPSXObjects false /PDFX1aCheck false /PDFX3Check false /PDFXCompliantPDFOnly false /PDFXNoTrimBoxError true /PDFXTrimBoxToMediaBoxOffset [ 0.00000 0.00000 0.00000 0.00000 ] /PDFXSetBleedBoxToMediaBox true /PDFXBleedBoxToTrimBoxOffset [ 0.00000 0.00000 0.00000 0.00000 ] /PDFXOutputIntentProfile () /PDFXOutputCondition () /PDFXRegistryName (http://www.color.org) /PDFXTrapped /Unknown
/Description >>> setdistillerparams> setpagedevice
Recommended