View
5
Download
0
Category
Preview:
Citation preview
Motor-drive UnitTAPMOTION® TD ISM®
Operating Instructions
4489615/01 EN . OEM-Control-Box
© All rights reserved by Maschinenfabrik ReinhausenDissemination and reproduction of this document and use and disclosure of its content are strictly prohibitedunless expressly permitted.Infringements will result in liability for compensation. All rights reserved in the event of the granting of patents,utility models or designs.The product may have been altered since this document was published.We reserve the right to change the technical data, design and scope of supply.Generally the information provided and agreements made when processing the individual quotations and ordersare binding.The original operating instructions were written in German.
Table of contents
Maschinenfabrik Reinhausen GmbH 2016 34489615/01 EN TAPMOTION® TD ISM®
Table of contents
1 Introduction......................................................................................................................... 51.1 Validity................................................................................................................................................. 5
1.2 Manufacturer....................................................................................................................................... 5
1.3 Subject to change without notice......................................................................................................... 5
1.4 Supporting documents......................................................................................................................... 5
1.5 Safekeeping......................................................................................................................................... 6
1.6 Notation conventions........................................................................................................................... 61.6.1 Symbols................................................................................................................................................................. 6
1.6.2 Hazard communication system............................................................................................................................. 7
1.6.3 Information system................................................................................................................................................ 8
1.6.4 Instruction system................................................................................................................................................. 8
1.6.5 Typographic conventions...................................................................................................................................... 9
2 Safety................................................................................................................................. 102.1 General safety information................................................................................................................ 10
2.2 Appropriate use................................................................................................................................. 10
2.3 Inappropriate use............................................................................................................................... 10
2.4 Personnel qualification...................................................................................................................... 11
2.5 Operator's duty of care...................................................................................................................... 11
2.6 Personal protective equipment.......................................................................................................... 11
3 Product description.......................................................................................................... 133.1 Scope of delivery............................................................................................................................... 13
3.2 Function description.......................................................................................................................... 13
3.3 Design............................................................................................................................................... 13
4 Packaging, transport and storage................................................................................... 154.1 Packaging.......................................................................................................................................... 154.1.1 Suitability............................................................................................................................................................. 15
4.1.2 Markings.............................................................................................................................................................. 15
4.2 Transportation, receipt and handling of shipments............................................................................ 16
4.3 Storage of shipments......................................................................................................................... 17
4.4 Unpacking shipments and checking for transportation damages...................................................... 18
5 Installation and commissioning...................................................................................... 19
Table of contents
Maschinenfabrik Reinhausen GmbH 20164 4489615/01 ENTAPMOTION® TD ISM®
6 Operation........................................................................................................................... 21
7 Maintenance and care....................................................................................................... 22
8 Fault elimination................................................................................................................ 23
9 Disposal............................................................................................................................. 24
10 Technical data................................................................................................................... 25
1 Introduction
Maschinenfabrik Reinhausen GmbH 2016 54489615/01 EN TAPMOTION® TD ISM®
IntroductionThis technical file contains detailed descriptions on the safe and proper in-stallation, connection, commissioning and monitoring of the product.
It also includes safety instructions and general information about the prod-uct.
This technical file is intended solely for specially trained and authorized per-sonnel.
ValidityThis technical file is valid for the TAPMOTION® TD ISM® product.
ManufacturerThe product is manufactured by:
Maschinenfabrik Reinhausen GmbH
Falkensteinstraße 893059 Regensburg, GermanyTel.: (+49) 9 41/40 90-0Fax: (+49) 9 41/40 90-7001E-mail: sales@reinhausen.com
Further information on the product and copies of this technical file are avail-able from this address if required.
Subject to change without noticeThe information contained in this technical file comprises the technical speci-fications approved at the time of printing. Significant modifications will be in-cluded in a new edition of the technical file.
The document number and version number of this technical file are shown inthe footer.
Supporting documentsThe following documents also apply in addition to this technical file:▪ Connection diagrams▪ Routine test report▪ Supplement
Also observe generally valid legislation, standards, guidelines and specifica-tions on accident prevention and environmental protection in the respectivecountry of use.
1
1.1
1.2
1.3
1.4
1 Introduction
Maschinenfabrik Reinhausen GmbH 20166 4489615/01 ENTAPMOTION® TD ISM®
SafekeepingThis technical file and all supporting documents must be kept ready at handand accessible for future use at all times.
Notation conventionsThis section contains an overview of the symbols and textual emphasisused.
Symbols
Symbol MeaningWrench size
Tightening torque
Number and type of fastening materials used
Fill with oil
Cut open, cut through
Clean
Visual inspection
Use your hand
Adapter ring
Apply a coat of paint
Use a file
Grease
1.5
1.6
1.6.1
1 Introduction
Maschinenfabrik Reinhausen GmbH 2016 74489615/01 EN TAPMOTION® TD ISM®
Symbol MeaningCoupling bolt
Use a ruler
Use a saw
Hose clip
Wire eyelet, safety wire
Use a screwdriver
Table 1: Symbols
Hazard communication system
Warnings in this technical file are displayed as follows.
Warning relating to section
Warnings relating to sections refer to entire chapters or sections, sub-sec-tions or several paragraphs within this technical file. Warnings relating tosections use the following format:
WARNING Type and source of dangerConsequences► Action► Action
Embedded warning information
Embedded warnings refer to a particular part within a section. These warn-ings apply to smaller units of information than the warnings relating to sec-tions. Embedded warnings use the following format:
DANGER! Instruction for avoiding a dangerous situation.
Signal words and pictograms
The following signal words are used:
1.6.2
1.6.2.1
1.6.2.2
1.6.2.3
1 Introduction
Maschinenfabrik Reinhausen GmbH 20168 4489615/01 ENTAPMOTION® TD ISM®
Signalword
Meaning
DANGER Indicates a hazardous situation which, if not avoided, willresult in death or serious injury.
WARNING Indicates a hazardous situation which, if not avoided, couldresult in death or serious injury.
CAUTION Indicates a hazardous situation which, if not avoided, couldresult in injury.
NOTICE Indicates measures to be taken to prevent damage toproperty.
Table 2: Signal words in warning notices
Pictograms warn of dangers:
Pictogram MeaningWarning of a danger point
Warning of dangerous electrical voltage
Warning of combustible substances
Warning of danger of tipping
Table 3: Pictograms used in warning notices
Information system
Information is designed to simplify and improve understanding of particularprocedures. In this technical file it is laid out as follows:
Important information.
Instruction system
This technical file contains single-step and multi-step instructions.
1.6.3
1.6.4
1 Introduction
Maschinenfabrik Reinhausen GmbH 2016 94489615/01 EN TAPMOTION® TD ISM®
Single-step instructions
Instructions which consist of only a single process step are structured as fol-lows:
Aim of actionü Requirements (optional).► Step 1 of 1.
ð Result of step (optional).ð Result of action (optional).
Multi-step instructions
Instructions which consist of several process steps are structured as follows:
Aim of actionü Requirements (optional).1. Step 1.
ð Result of step (optional).2. Step 2.
ð Result of step (optional).ð Result of action (optional).
Typographic conventions
The following typographic conventions are used in this technical file:
Typographic convention Purpose ExampleUPPERCASE Operating controls, switches ON/OFF[Brackets] PC keyboard [Ctrl] + [Alt]Bold Software operating controls Press Continue button…>…>… Menu paths Parameter > Control parameterItalics System messages, error mes-
sages, signalsFunction monitoring alarm trig-gered
[► Number of pages]. Cross reference [► 41].Table 4: Typographic conventions
1.6.5
2 Safety
Maschinenfabrik Reinhausen GmbH 201610 4489615/01 ENTAPMOTION® TD ISM®
Safety
General safety informationThe technical file contains detailed descriptions on the safe and proper in-stallation, connection, commissioning and monitoring of the product.▪ Read this technical file through carefully to familiarize yourself with the
product.▪ Particular attention should be paid to the information given in this chap-
ter.
Appropriate useIf used as intended and in compliance with the requirements and conditionsspecified in this technical file as well as the warning notices in this technicalfile and attached to the product, then the product does not present any haz-ards to people, property or the environment. This applies throughout theproduct's entire life, from delivery through installation and operation to disas-sembly and disposal.
The operational quality assurance system ensures a consistently high qualitystandard, particularly in regard to the observance of health and safety re-quirements.
The following is considered appropriate use▪ Only operate the product in accordance with this technical file and the
agreed delivery conditions and technical data.▪ Always operate the product under supervision.▪ Use the equipment and special tools supplied solely for the intended
purpose and in accordance with the specifications of this technical file.▪ Only use the product for commissioning an on-load tap-changer using
the TAPMOTION® TD ISM® motor-drive unit.
Inappropriate useUse is considered to be inappropriate if the product is used other than as de-scribed in the Appropriate use section. Please also note the following:▪ Risk of explosion and fire from highly flammable or explosive gases, va-
pors, or dusts. Do not operate product in areas at risk of explosion.▪ Risk of personal injury and damage to property from electric shock. Do
not use product on an energized transformer.▪ Unauthorized or inappropriate changes to the product may lead to per-
sonal injury, material damage, and operational faults. Only modify prod-uct following discussion with Maschinenfabrik Reinhausen GmbH.
2
2.1
2.2
2.3
2 Safety
Maschinenfabrik Reinhausen GmbH 2016 114489615/01 EN TAPMOTION® TD ISM®
Personnel qualificationThe product is designed solely for use in electrical energy systems and facili-ties operated by appropriately trained staff. This staff comprises people whoare familiar with the installation, assembly, commissioning and operation ofsuch products.
Operator's duty of careTo prevent accidents, disruptions and damage as well as unacceptable ad-verse effects on the environment, those responsible for transport, installa-tion, operation, maintenance and disposal of the product or parts of the prod-uct must ensure the following:▪ All warning and hazard notices are complied with.▪ Personnel are instructed regularly in all relevant aspects of operational
safety, the operating instructions and particularly the safety instructionscontained therein.
▪ Regulations and operating instructions for safe working as well as therelevant instructions for staff procedures in the case of accidents andfires are kept on hand at all times and are displayed in the workplacewhere applicable.
▪ The product is only used when in a sound operational condition andsafety equipment in particular is checked regularly for operational relia-bility.
▪ Only replacement parts, lubricants and auxiliary materials which are au-thorized by the manufacturer are used.
▪ The specified operating conditions and requirements of the installationlocation are complied with.
▪ All necessary devices and personal protective equipment for the specificactivity are made available.
▪ The prescribed maintenance intervals and the relevant regulations arecomplied with.
▪ Installation, electrical connection and commissioning of the product mayonly be carried out by qualified and trained personnel in accordancewith this technical file.
▪ The operator must ensure appropriate use of the product.
Personal protective equipmentPersonal protective equipment must be worn during work to minimize risks tohealth.▪ Always wear the personal protective equipment required for the job at
hand.▪ Follow information about personal protective equipment provided in the
work area.
2.4
2.5
2.6
2 Safety
Maschinenfabrik Reinhausen GmbH 201612 4489615/01 ENTAPMOTION® TD ISM®
Always wear Protective clothingClose-fitting work clothing with a lowbreaking strength, with tight sleeves andwith no protruding parts. It mainly servesto protect the wearer against being caughtby moving machine parts.Do not wear any rings, necklaces or otherjewelry.Safety shoesTo protect against falling heavy objectsand slipping on slippery surfaces.
Table 5: Personal protective equipment to be worn at all times
Wear the following in spe-cial environments
Special personal protective equipmentis needed in special environments.The choice of equipment depends onthe circumstances.Safety glassesTo protect the eyes from flying parts andsplashing liquids.
Hard hatTo protect from falling and flying parts andmaterials.
Hearing protectionTo protect from hearing damage.
Table 6: Personal protective equipment to be worn in special environments
3 Product description
Maschinenfabrik Reinhausen GmbH 2016 134489615/01 EN TAPMOTION® TD ISM®
Product descriptionThis chapter contains an overview of the design and function of the product.
Scope of deliveryThe OEM Control Box is packaged with protection against moisture and isdelivered as follows:▪ OEM Control Box▪ Product documentation
Please note the following:► Check the shipment for completeness using the shipping documents.
Function descriptionThe OEM Control Box is used to actuate the TAPMOTION® TD ISM® mo-tor-drive unit's gear motor manually if the control cabinet is not yet installedand connected (e.g. for test tap-change operations at the transformer plant).
DesignThe OEM Control Box consists of the following components:
Figure 1: OEM Control Box
1 OEM Control Box 3 Control cable2 Connecting lead
3
3.1
3.2
3.3
3 Product description
Maschinenfabrik Reinhausen GmbH 201614 4489615/01 ENTAPMOTION® TD ISM®
The OEM Control Box contains the following operating controls and displayelements:
Figure 2: Operating controls
1 Motor protective switch 2 In Position LED3 Error LED 4 EMERGENCY OFF switch5 AUTO/MANUAL switch 6 N key7 1 key
4 Packaging, transport and storage
Maschinenfabrik Reinhausen GmbH 2016 154489615/01 EN TAPMOTION® TD ISM®
Packaging, transport and storage
PackagingThe products are sometimes supplied with a sealed packaging and some-times also dried depending on what is required.
A sealed packaging surrounds the packaged goods on all sides with plasticfoil. Products that have also been dried are identified by a yellow label on thesealed packaging.
The information in the following sections should be applied as appropriate.
Suitability
NOTICE
Property damage due to incorrectly stacked crates!Stacking the crates incorrectly can lead to damage to the packaged goods!► Only stack up to 2 equally sized crates on top of one another.
The packaging is suitable for undamaged and fully functional means oftransportation in compliance with local transportation laws and regulations.
The packaged goods are packed in a stable crate. This crate ensures thatthe packaged goods are secure when in the intended transportation positionand that none of the parts touch the loading surface of the means of trans-port or touch the ground after unloading.
The packaged goods are stabilized inside the crate to prevent impermissiblechanges in position.
A sealed packaging surrounds the packaged goods on all sides with plasticfoil. The packaged goods are protected from humidity using a desiccant. Theplastic foil is bonded after the drying agent is added.
Markings
The packaging bears a signature with instructions for safe transport and cor-rect storage. The following symbols apply to the shipment of non-hazardousgoods. Adherence to these symbols is mandatory.
Protectagainst
moisture
Top Fragile Attach liftinggear here
Center ofmass
Table 7: Shipping pictograms
4
4.1
4.1.1
4.1.2
4 Packaging, transport and storage
Maschinenfabrik Reinhausen GmbH 201616 4489615/01 ENTAPMOTION® TD ISM®
Transportation, receipt and handling of shipments
WARNING Danger of death and damage to property!Danger of death and damage to property due to tipping or falling load!► Transport crate only when closed.► Do not remove the mounting material used in the crate during transport.► Only trained and appointed persons may select the sling gear and se-
cure the load.► Do not walk under the hanging load.► Use means of transport and lifting gear with a sufficient carrying capaci-
ty in accordance with the weight stated on the delivery slip.
In addition to oscillation stress and shock stress, jolts must also be expectedduring transportation. In order to prevent possible damage, avoid dropping,tipping, knocking over and colliding with the product.
If a crate tips over, falls from a certain height (e.g. when slings tear) or expe-riences an unbroken fall, damage must be expected regardless of theweight.
Every delivered shipment must be checked for the following by the recipientbefore acceptance (acknowledgment of receipt):▪ Completeness based on the delivery slip▪ External damage of any type.
The checks must take place after unloading when the crate or transport con-tainer can be accessed from all sides.
If external transport damage is detected on receipt of the shipment, proceedas follows:▪ Immediately record the transport damage found in the shipping docu-
ments and have this countersigned by the carrier.▪ In the event of severe damage, total loss or high damage costs, immedi-
ately notify the sales department at Maschinenfabrik Reinhausen andthe relevant insurance company.
▪ After identifying damage, do not modify the condition of the shipmentfurther and retain the packaging material until an inspection decisionhas been made by the transport company or the insurance company.
▪ Record the details of the damage immediately onsite together with thecarrier involved. This is essential for any claim for damages!
▪ Photograph damage to packaging and packaged goods. This also ap-plies to signs of corrosion on the packaged goods due to moisture insidethe packaging (rain, snow, condensation).
▪ NOTICE! Be absolutely sure to also check the sealed packaging. If thesealed packaging is damaged, do not under any circumstances install orcommission the packaged goods. Either dry the dried packaged goodsagain as per the operating instructions for the relevant on-load tap-
4.2
Visible damage
4 Packaging, transport and storage
Maschinenfabrik Reinhausen GmbH 2016 174489615/01 EN TAPMOTION® TD ISM®
changer/off-circuit tap-changer or contact Maschinenfabrik ReinhausenGmbH to agree on how to proceed with drying. If this is not done, thepackaged goods may be damaged.
▪ Name the damaged parts.
When damages are not determined until unpacking after receipt of the ship-ment (hidden damage), proceed as follows:▪ Make the party responsible for the damage liable as soon as possible by
telephone and in writing, and prepare a damage report.▪ Observe the time periods applicable to such actions in the respective
country. Inquire about these in good time.
With hidden damage, it is very hard to make the transportation company (orother responsible party) liable. Any insurance claims for such damages canonly be successful if relevant provisions are expressly included in the insur-ance terms and conditions.
Storage of shipments
Packaged goods dried by Maschinenfabrik Reinhausen
Upon receipt of the shipment, immediately remove the packaged goodsdried by Maschinenfabrik Reinhausen from the sealed packaging and storeair-tight in dry insulating oil until used.
Non-dried packaged goods
Non-dried packaged goods but with a functional sealed packaging can bestored outdoors when the following conditions are complied with.
When selecting and setting up the storage location, ensure the following:▪ Protect stored goods against moisture (flooding, water from melting
snow and ice), dirt, pests such as rats, mice, termites and so on, andagainst unauthorized access.
▪ Store the crates on timber beams and planks as a protection against ris-ing damp and for better ventilation.
▪ Ensure sufficient carrying capacity of the ground.▪ Keep entrance paths free.▪ Check stored goods at regular intervals. Also take appropriate action af-
ter storms, heavy rain or snow and so on.
Protect the packaging foil from direct sunlight so that it does not disintegrateunder the influence of UV rays, which would cause the packaging to lose itssealing function.
If the product is installed more than 6 months after delivery, suitable meas-ures must be taken without delay. The following measures can be used:▪ Correctly regenerate the drying agent and restore the sealed packaging.
Hidden damage
4.3
4 Packaging, transport and storage
Maschinenfabrik Reinhausen GmbH 201618 4489615/01 ENTAPMOTION® TD ISM®
▪ Unpack the packed goods and store in suitable storage space (well ven-tilated, as dust-free as possible, humidity < 50 % where possible).
Unpacking shipments and checking for transportationdamages▪ NOTICE! Transport the packaged crate to the place where installation
will take place. Do not open the sealed packaging until just before instal-lation. If this is not done, damage to the packaged goods may occur dueto ineffectively sealed packaging.
▪ WARNING! When unpacking, check the condition of the packagedgoods.Secure packaged goods in an upright crate from tipping out. Ifthis is not done, the packaged goods may be damaged and serious inju-ries may result.
▪ Check completeness of supplementary parts on the basis of the deliveryslip.
4.4
5 Installation and commissioning
Maschinenfabrik Reinhausen GmbH 2016 194489615/01 EN TAPMOTION® TD ISM®
Installation and commissioningThis chapter describes how to correctly connect and commission the OEMControl Box.
WARNING Risk of severe injury or death!An energized transformer and energized on-load tap-changer componentscan cause death or serious injuries when installing the motor-drive unit!► Ensure de-energized state of transformer and on-load tap-changer
components during the installation of the motor-drive unit.
You may only connect the OEM Control Box to circuits with an external over-current protection device and an isolating device with all poles disconnectedso the equipment can be fully de-energized if required (service, maintenanceetc.).
Suitable equipment includes isolating devices in accordance with IEC60947-1 and IEC60947-3 (e.g. circuit breaker). When selecting the circuitbreaker type, note the properties of the relevant circuits (voltage, maximumcurrents). Please also note the following:▪ It must be easy for the operator to access the isolating device▪ The isolating device must be labeled for the device circuits to be isolat-
ed▪ The isolating device must not be part of the power line▪ The isolating device must not interrupt the main grounding conductor
You must fuse the power supply circuit with a C16A type miniature circuitbreaker.
To install and commission the OEM Control Box, proceed as follows:1. Connect the connecting lead to the gear motor's plug connector.2. Connect OEM Control Box to the power supply.
The CEE plug for the OEM Control Box power supply is configured for aclockwise rotary field.
5
5 Installation and commissioning
Maschinenfabrik Reinhausen GmbH 201620 4489615/01 ENTAPMOTION® TD ISM®
3. Configure motor protective switch according to the gear motor's ratedcurrent and tripping class. To do so, note the table below.
Figure 3: Configuring motor protective switch
Rated current and tripping class of the gear motor
Motor designation In CLASS
380 V 400 V 440 VGear motor VM 50 Hz 1.0 A 10Gear motor VM 60 Hz 1.0 AGear motor VV 50 Hz 1.4 A 1.4 A 1.8 AGear motor VV 60 Hz 1.4 A 1.5 A 1.7 A
Table 8: Rated current (In) and tripping class (CLASS) of the connected gear motor
6 Operation
Maschinenfabrik Reinhausen GmbH 2016 214489615/01 EN TAPMOTION® TD ISM®
OperationYou can control the TAPMOTION® TD ISM® motor-drive unit's gear motorusing the OEM Control Box in two different operating modes:▪ MANUAL: In MANUAL mode, the gear motor only runs as long as key 1
or N is pressed and held down. This allows you to move the gear motorincrementally.
▪ AUTO: In AUTO operating mode, the gear motor runs until the on-loadtap-change operation is completely finished after pressing key 1 or N.
To activate the gear motor, proceed as follows:1. Move MANUAL/AUTO switch to the desired position to select the oper-
ating mode.2. Press or press and hold key 1 or key N to activate the gear motor ac-
cording to the operating mode selected.ð The gear motor runs. Then, if the gear motor is in a defined tap position,
the In Position lamp lights up. Otherwise, the Error lamp lights up.
6
7 Maintenance and care
Maschinenfabrik Reinhausen GmbH 201622 4489615/01 ENTAPMOTION® TD ISM®
Maintenance and careYou can clean the device's housing with a dry cloth.
7
8 Fault elimination
Maschinenfabrik Reinhausen GmbH 2016 234489615/01 EN TAPMOTION® TD ISM®
Fault eliminationThis chapter describes how to eliminate simple operating faults.
Characteristics/detail Cause RemedyNo function in AUTOoperating mode▪ ERROR LED
lights up
On-load tap-changer is inimpermissible position
Bring on-load tap-changer to a permissible posi-tion:1. Select MANUAL mode.2. Push key 1 or key N to move the on-load
tap-changer into a permissible position. Ifthe tap changer is in a permissible position,the IN POSITION lamp lights up.
No function No power supply Check power supply.Miniature circuit breaker F14triggered
Engaging miniature circuit breaker:1. Remove device from the network.2. Remove cover plate cross recessed head
screws and lift cover plate.3. Engaging miniature circuit breaker F14:4. Install cover plate.5. Connect device and check function.If faults persist: contact Maschinenfabrik Rein-hausen GmbH.
Miscellaneous error Contact Maschinenfabrik Reinhausen.Table 9: Fault elimination
Other faults
In the event of faults that cannot be easily corrected on site, please informyour authorized MR representative or contact us directly:
Maschinenfabrik Reinhausen GmbHTechnical ServicePostfach 12 03 6093025 RegensburgGermany
Phone: (+49) 9 41/40 90-0Fax: (+49) 9 41/40 90-7001
E-mail: service@reinhausen.comInternet: www.reinhausen.com
8
9 Disposal
Maschinenfabrik Reinhausen GmbH 201624 4489615/01 ENTAPMOTION® TD ISM®
DisposalThe device was produced in accordance with European Community Direc-tive 2011/65/EC (RoHS) and must be disposed of accordingly. If the deviceis not operated within the European Union, the national disposal require-ments applicable in the country of use should be observed.
9
10 Technical data
Maschinenfabrik Reinhausen GmbH 2016 254489615/01 EN TAPMOTION® TD ISM®
Technical data
Dimensions and weight
Dimensions (W x H x D) 265 x 315 x 198 mmWeight 1.7 kg
Table 10: Dimensions and weight
Electrical connection loads
Power supply 400 VACFrequency 50/60 HzPower consumption approx. 4 AFuse Miniature circuit breaker 1.6 A type
C
Motor protective switch, dependingon the setting of the gear motor'srated current
Table 11: Electrical connection loads
Figure 4: Position of the miniature circuit breaker if cover plate is disassembled
F14 Miniature circuit breaker
Ambient conditions
Degree of protection IP65 (if cover closed)Operating temperature 5...40 °CStorage temperature -20…+50 °C
Table 12: Ambient conditions
10
MR worldwideAustraliaReinhausen Australia Pty. Ltd.17/20-22 St Albans RoadKingsgrove NSW 2208Phone: +61 2 9502 2202Fax: +61 2 9502 2224E-Mail: sales@au.reinhausen.com
BrazilMR do Brasil Indústria Mecánica Ltda.Av. Elias Yazbek, 465CEP: 06803-000Embu - São PauloPhone: +55 11 4785 2150Fax: +55 11 4785 2185E-Mail: vendas@reinhausen.com.br
CanadaReinhausen Canada Inc.3755, rue Java, Suite 180Brossard, Québec J4Y 0E4Phone: +1 514 370 5377Fax: +1 450 659 3092E-Mail: m.foata@ca.reinhausen.com IndiaEasun-MR Tap Changers Ltd. (Joint Venture)612, CTH RoadTiruninravur, Chennai 602 024Phone: +91 44 26300883Fax: +91 44 26390881E-Mail: service@easunmr.com IndonesiaPt. Reinhausen IndonesiaGerman Center, Suite 6310,Jl. Kapt. Subijanto Dj.BSD City, TangerangPhone: +62 21 5315-3183Fax: +62 21 5315-3184E-Mail: c.haering@id.reinhausen.com
IranIran Transfo After Sales Services Co.(Joint Venture)Zanjan, Industrial Township No. 1 (Aliabad)Corner of Morad Str.Postal Code 4533144551E-Mail: itass@iran-transfo.com ItalyReinhausen Italia S.r.l.Via Alserio, 1620159 MilanoPhone: +39 02 6943471Fax: +39 02 69434766E-Mail: sales@it.reinhausen.com JapanMR Japan CorporationGerman Industry Park1-18-2 Hakusan, Midori-kuYokohama 226-0006Phone: +81 45 929 5728Fax: +81 45 929 5741 LuxembourgReinhausen Luxembourg S.A.72, Rue de PrésL-7333 SteinselPhone: +352 27 3347 1Fax: +352 27 3347 99E-Mail: sales@lu.reinhausen.com
MalaysiaReinhausen Asia-Pacific Sdn. BhdLevel 11 Chulan TowerNo. 3 Jalan Conlay50450 Kuala LumpurPhone: +60 3 2142 6481Fax: +60 3 2142 6422E-Mail: mr_rap@my.reinhausen.com
P.R.C. (China)MR China Ltd. (MRT)开德贸易(上海)有限公司
中国上海浦东新区浦东南路 360 号
新上海国际大厦 4楼 E座
邮编: 200120
电话:+ 86 21 61634588
传真:+ 86 21 61634582
邮箱:mr-sales@cn.reinhausen.com
mr-service@cn.reinhausen.com
Russian FederationOOO MRNaberezhnaya Akademika Tupoleva15, Bld. 2 ("Tupolev Plaza")105005 MoscowPhone: +7 495 980 89 67Fax: +7 495 980 89 67E-Mail: mrr@reinhausen.ru
South AfricaReinhausen South Africa (Pty) Ltd.No. 15, Third Street, Booysens ReserveJohannesburgPhone: +27 11 8352077Fax: +27 11 8353806E-Mail: support@za.reinhausen.com South KoreaReinhausen Korea Ltd.21st floor, Standard Chartered Bank Bldg.,47, Chongro, Chongro-gu,Seoul 110-702Phone: +82 2 767 4909Fax: +82 2 736 0049E-Mail: you-mi.jang@kr.reinhausen.com
U.S.A.Reinhausen Manufacturing Inc.2549 North 9th AvenueHumboldt, TN 38343Phone: +1 731 784 7681Fax: +1 731 784 7682E-Mail: sales@reinhausen.com United Arab EmiratesReinhausen Middle East FZEDubai Airport Freezone, Building Phase 63rd floor, Office No. 6EB, 341 DubaiPhone: +971 4 2368 451Fax: +971 4 2368 225Email: service@ae.reinhausen.com
Maschinenfabrik Reinhausen GmbHFalkensteinstrasse 893059 Regensburg
+49 (0)941 4090-0+49(0)941 4090-7001sales@reinhausen.com
www.reinhausen.com
4489615/01 EN ▪ 02/16 ▪
Recommended