View
3
Download
0
Category
Preview:
Citation preview
Unidad de Mecanización Agrariahttp://uma.deab.upc.eduUnidad de Mecanización Agraria
Manual for inspection of sprayers in use and PRITEAF, software for inspection of sprayers: success tools
developed for the inspector’s training process in Spain
Emilio Gil 1, Ángel Jiménez 2 Javier García‐Ramos 2
1 Universidad Politécnica de CataluñaDepartamento de Ingeniería Agroalimentaria y Biotecnología
2 Universidad de ZaragozaEscuela Politécnica Superior de Huesca
Unidad de Mecanización Agrariahttp://uma.deab.upc.eduUnidad de Mecanización Agraria
Inspector’s training: key point for success
Official certificate mandatory for Directors andTechnicians of workshopsThis certificate (renewable every 5 years) will beacquired after the attendance to mandatory trainingcourses delivered by official institutions
What?
Who?
Universities (AgEng Departments)Official training centersResearch and Development InstitutesWhatever other official institution if consideredLocal authorities will design their own training facilities
Unidad de Mecanización Agrariahttp://uma.deab.upc.eduUnidad de Mecanización Agraria
Inspector’s training: key point for success
Unidad de Mecanización Agrariahttp://uma.deab.upc.eduUnidad de Mecanización Agraria
Training… or at least Information
Results of visual inspection must be explained/commented with the farmerduring the procedure itself.
Results of different measurements (nozzle flow rate, pressure gauge,horizontal distribution,…) must be explained (time consuming estimated 5‐10 min) immediately after the measurement process.
Those actions will increase the success on the comprehension of inspectionbulletin and will promote the modification/changes necessaries on thesprayer
Unidad de Mecanización Agrariahttp://uma.deab.upc.eduUnidad de Mecanización Agraria
Difficulties in the interpretation of standards (EN 13790 & ISO 16122)
Boquillas Caudal nominal (L/min)
Izquierda Derecha
Caudal (L/min)
Desviación Caudal (L/min)
Desviación Respecto al
caudal nominal (%)
Respecto al caudal medio (%)
Respecto al caudal
nominal (%)
Respecto al caudal medio (%)
5 ATR Naranja 0,99 0,99 0,00 4,10 0,95 -4,04 -0,11 4 ATR Naranja 0,99 0,96 -3,03 0,95 0,95 -4,04 -0,11 3 ATR Naranja 0,99 0,95 -4,04 -0,11 0,94 -5,05 -1,16 2 ATR Naranja 0,99 0,96 -3,03 0,95 0,94 -5,05 -1,16 1 ATR Naranja 0,99 0,93 -6,06 -2,21 0,94 -5,05 -1,16
Porcentaje respecto al caudal total 50,37 49,63 Desv. respecto al 50% del caudal (%) -0,37 0,37
Boquillas Caudal nominal (L/min)
Izquierda Derecha
Caudal (L/min)
Desviación Caudal (L/min)
Desviación Respecto al
caudal nominal (%)
Respecto al caudal medio (%)
Respecto al caudal
nominal (%)
Respecto al caudal medio (%)
5 ATR Naranja 0,99 0,99 0,00 4,10 0,95 -4,04 -0,11 4 ATR Naranja 0,99 0,96 -3,03 0,95 0,95 -4,04 -0,11 3 ATR Naranja 0,99 0,95 -4,04 -0,11 0,94 -5,05 -1,16 2 ATR Naranja 0,99 0,96 -3,03 0,95 0,94 -5,05 -1,16 1 ATR Naranja 0,99 0,93 -6,06 -2,21 0,94 -5,05 -1,16
Porcentaje respecto al caudal total 50,37 49,63 Desv. respecto al 50% del caudal (%) -0,37 0,37
Unidad de Mecanización Agrariahttp://uma.deab.upc.eduUnidad de Mecanización Agraria
Need of some Official Guide
Dr. Emilio Gil (coordinador)Universidad Politécnica de Cataluña
Sr. Felipe GraciaCMA – Generalitat de Catalunya
Dr. Alexandre EscolàUniversidad de Lleida
Unidad de Mecanización Agrariahttp://uma.deab.upc.eduUnidad de Mecanización Agraria
Common part
Transmisión de potenciaBombaAgitaciónDepósitoSistemas de medición y regulaciónTuberías rígidas y flexiblesFiltros
Specific part
• Pulverizadores hidráulicos• Pulverizadores hidroneumáticos• Pulverizadores neumáticos• Pistolas de pulverización• Espolvoreadores
Inspections’ equipment
Contents of the Manual
Unidad de Mecanización Agrariahttp://uma.deab.upc.eduUnidad de Mecanización Agraria
General structure of the Manual of Inspections
Unidad de Mecanización Agrariahttp://uma.deab.upc.eduUnidad de Mecanización Agraria
Estabilidadysimetríadelabarra.
La barra debe permanecer estable en todas las direcciones, es decir, no hay juntas con holguras ni se pliegan las distintas secciones de la barra. Las secciones derecha e izquierda de la barra deben tener la misma longitud.
Método de verificación: inspección.
Correspondencia con la normativa: UNE-EN 13790-1, apartado 4.8.1.
Actuación del inspector
El inspector procederá a intentar mover la barra en todas las direcciones para comprobar su estabilidad. También procederá a comprobar que las juntas de la barra no presentan más holgura que la necesaria para su plegado y desplegado. Se situará en un extremo de la barra cuando ésta se encuentre desplegada y observará que no está torcida, que toda la barra está contenida en un mismo plano vertical perpendicular al sentido de avance del pulverizador. Finalmente, medirá la longitud del centro de la barra a cada uno de los extremos para comprobar que son iguales.
Resultados de la verificación
ESTADO CLASIFICACIÓN EFECTO La barra es estable y no está torcida. Las juntas no presentan holguras excesivas y ambos lados de la barra presentan la misma longitud.
Sin defecto Requisito satisfecho
La barra presenta ciertos movimientos pero mantiene generalmente la estabilidad Defecto leve
Recomendación de adecuación y correcto funcionamiento.
La barra no es estable o está excesivamente doblada o presenta holguras excesivas o no tienen la misma longitud ambos lados
Defecto grave Inspección desfavorable
Title Text as EN 13790
Method of verification
Chapter of EN 13790
Practical recommendations
Results and interpretation
Unidad de Mecanización Agrariahttp://uma.deab.upc.eduUnidad de Mecanización Agraria
Favorable examples
How to proceed
Not favorable examples
Unidad de Mecanización Agrariahttp://uma.deab.upc.eduUnidad de Mecanización Agraria
“…the recommendations of Session 6 concerning criteria for rejecting the sprayers,authorization and monitoring of workshops should be considered by the Member States todevelop further regulations/protocols,…” (SPISE, Brno, September 2009)
ESTADO CLASIFICACIÓN EFECTO La barra es estable y no está torcida. Las juntas no presentan holguras excesivas y ambos lados de la barra presentan la misma longitud.
Sin defecto Requisito satisfecho
La barra presenta ciertos movimientos pero mantiene generalmente la estabilidad Defecto leve
Recomendación de adecuación y correcto funcionamiento.
La barra no es estable o está excesivamente doblada o presenta holguras excesivas o no tienen la misma longitud ambos lados
Defecto grave Inspección desfavorable
Criteria for evaluation
Unidad de Mecanización Agrariahttp://uma.deab.upc.eduUnidad de Mecanización Agraria
PRITEAF – Specific software for inspection of sprayers in use in Spain
Authorized Workshop
Control of inspection unitsDatabase
Transfer info to official bodyOfficial certificates
Inspection Unit
Inspection protocolData storage
Sprayer’s inspection
Official authority
Data baseOfficial registration
Statistics
Unidad de Mecanización Agrariahttp://uma.deab.upc.eduUnidad de Mecanización Agraria
PRITEAF – Useful database
Spray manufacturers Spray Nozzles Owners / inspections
Unidad de Mecanización Agrariahttp://uma.deab.upc.eduUnidad de Mecanización Agraria
Unidad de Mecanización Agrariahttp://uma.deab.upc.eduUnidad de Mecanización Agraria
Official certificate and inspection report
UFI ‐ Curso Director/Inspector EAF 2014
Directly form main menuAfter the inspection procedure
Unidad de Mecanización Agrariahttp://uma.deab.upc.eduUnidad de Mecanización Agraria
Unidad de Mecanización Agrariahttp://uma.deab.upc.eduUnidad de Mecanización Agraria
Identification of the inspection team
Identification of the sprayer owner
Identification of the machine
Verification of safety requirements
Verification of the overall operation of
the sprayer
Checking of correct operation of
nozzles, pump and control system
Checking of tank components
Checking of pump, safety valve and
pipes
Measurement of flow rates of
nozzles
Measurement of pressures at control points and checking of pressure control
devices
Checking of filters: condition and leaks
Usage recommendations
Issue of report and certificate
Printing and saving documents
Generation of inspection
document for the workshop director
Generation of periodic activity
report for the Regional Authority
Unidad de Mecanización Agrariahttp://uma.deab.upc.eduUnidad de Mecanización Agraria
Inspection report
Unidad de Mecanización Agrariahttp://uma.deab.upc.eduUnidad de Mecanización Agraria
Official certificate
UFI ‐ Curso Director/Inspector EAF 2014
Local authority
Result of the inspection
Deadline to repair / new inspection
Owner
Sprayer identification
Elements to repair / change
Inspection workshop / Responsible
Unidad de Mecanización Agrariahttp://uma.deab.upc.eduUnidad de Mecanización Agraria
Official Software
Inspection’s handbook
Developed tools to implement National Action Plans
Official inspector’s training
Mandatory inspections
Mandatory training
Official accomplishment of EU 2009/128/CE
Unidad de Mecanización Agrariahttp://uma.deab.upc.eduUnidad de Mecanización Agraria
Official training courses for inspectors in Spain(RD 1702/2011)
Inspector’s training, first step for quality assurance
Unidad de Mecanización Agrariahttp://uma.deab.upc.eduUnidad de Mecanización Agraria
Benefits after two years using those tools
More than 600 inspectors have been trained
Tools have been very well appreciated by the attendants
Inspection procedure is followed in a easy and educational way
Manufacturers have been also involved in EN 13790 knowledge
Good feed‐back have been generated among stakeholders
Official authorities have been adopted both as reference
Modifications can be arranged to be adapted to new standards
Unidad de Mecanización Agrariahttp://uma.deab.upc.eduUnidad de Mecanización Agraria
Manual and software available on internet
Manual of Inspections
http://uma.deab.upc.edu/inspeccion‐de‐equipos‐de‐aplicacion
http://www.magrama.gob.es/ca/agricultura/publicaciones/manual_inspeccion.aspx
Software for inspections
http://www.unizar.es/centros/eps/descarga_priteaf.htm
(in a short time)http://www.magrama.gob.es
Unidad de Mecanización Agrariahttp://uma.deab.upc.eduUnidad de Mecanización Agraria
Thank you very much for your attention
Recommended