View
214
Download
0
Category
Preview:
Citation preview
7/30/2019 liqliq
1/24
Lecture 7: Liquid-Liquid Ternary Single Stage1
Liquid-Liquid Extractions
This lecture will cover: Ternary Liquid -Liquid extractions. Ternary phase diagrams. A procedure to determine the product compositions and flow rates of a liquid-liquid extraction separation.
Last lecture covered: Using a simple spreadsheet to apply the Rachford RiceProcedure Bubble point and Dew Point temperature and pressure calculations An example of a dew point temperature calculation
7/30/2019 liqliq
2/24
Lecture 7: Liquid-Liquid Ternary Single Stage2
Liquid-Liquid Ternary Single Equilibrium Stage
We last covered the Flash Calculations where a liquid phase and a vapor phase werein equilibrium. For that system we needed equilibrium data, for example, from aDepriester chart to determine the distribution of components between the two phases.
Now well analyze the following system:
Ternary Liquid-Liquid Extraction In this case: We create two liquid phases by introducing a solvent (C) (MSA) to a liquid mixture of a carrier (A)
and a solute (B) Solvent (C) and carrier (A) have very little solubility in each other
Liquid Feed
Solvent Rich Liquid Out
Liquid-Liquid Extraction
F, A, B R, A, B, C
Carrier Rich Liquid out E, A, B, C
Solvent Feed
S, C
Define the raffinate as the exiting phase rich in carrier .Define the extract as the exiting phase rich in solvent .
7/30/2019 liqliq
3/24
Lecture 7: Liquid-Liquid Ternary Single Stage3
Liquid-Liquid Ternary Single Equilibrium Stage
If the solvent and carrier have some solubility in each other, then the raffinate will havea small amount of solvent in it and the extract will have a small concentration of carrier:
The raffinate is the exiting phase rich in carrier .The extract is the exiting phase rich in solvent .
Liquid Feed
Extract out
Liquid-Liquid Extraction
F, X A(F), X B, T, P R, X A (R), X B (R), X C (R), T, P
Raffinate out
E, X A (E), X B (E), X C (E), T, P
Solvent Feed
S, X C(S),T, P
7/30/2019 liqliq
4/24
Lecture 7: Liquid-Liquid Ternary Single Stage4
Liquid-Liquid Ternary Single Equilibrium Stage
If the solvent and carrier have no solubility in each other, then the raffinate willhave no solvent in it and the extract will have no carrier in it:
Liquid Feed
Extract out
Liquid-Liquid Extraction
F, X A(F), X B, T, P R, X A (R), X B (R), T, P
Raffinate out
E, X B (E), X C (E), T, P
Solvent Feed S, X C(S),T, P
The raffinate is the exiting phase rich in carrier .The extract is the exiting phase rich in solvent .
All of carrier exitsin the raffinate
All of solvent exitsin the extract
7/30/2019 liqliq
5/24
Lecture 7: Liquid-Liquid Ternary Single Stage5
Mass and Mole Ratios
Often the concentrations are as mass or mole ratios , rather than mass or mole fractions.This is generally done to simplify the expressions used in the analysis.
Mass ratio X B: The ratio of mass of component B to another component of the stream.Mole ratio X B: The ratio of moles of component B to another component of the stream.
Note that the basis (choice of component) for the mass or mole ratio must be chosen.
Liquid Feed
Extract out
F, X A(F), X B, T, P R, X A (R), X B (R), T, PRaffinate out
E, X B (E), X C (E), T, P
Solvent Feed S, X C(S),T, P
Mass Ratio Example :
F B X B F F A
E B X B E E C X B
E S
R B X B R R A X B
R F A
S B X BS
S C 0
Rate of B in the feed is the ratio of B to A, times feed rate of A.
Rate of B in the extract is the ratio of B to C, times rate of C.
Rate of B in the raffinate is the ratio of B to A, times rate of A.
Rate of B in the solvent is the ratio of B to C, times feed rate of C.
7/30/2019 liqliq
6/24
Lecture 7: Liquid-Liquid Ternary Single Stage6
Material Balances
Liquid Feed
Extract out
F, X A(F), X B R, X A (R), X B (R)Raffinate out
E, X B (E), X C (E)
Solvent Feed
S, X C(S)
Solute Material Balance :
F B X B F F A
E B X B E E C X B E S
R B X B R R A X B
R F A
S B X BS S C 0
Rate of B in the feed is the ratio of B to A, times feed rate of A.
Rate of B in the extract is the ratio of B to C, times rate of C.
Rate of B in the raffinate is the ratio of B to A, times rate of A.
Rate of B in the solvent is the ratio of B to C, times feed rate of C.
F B S B R B E B
X B F F A X B
S S C X B R R A X B
E E C
X B
F F A
X B
R F A
X B
E S
Solute Material Balance :
7/30/2019 liqliq
7/24Lecture 7: Liquid-Liquid Ternary Single Stage7
Equilibrium Distribution
The way the solute will distribute itself between the extract and raffinate atequilibrium is given by the K-Value:
X B E K D B
' X B
R
Note that the K-value is primed to signify that thisis a ratio of mass or moleratios, not a ratio of molefractions.
Liquid Feed
Extract out
F, X A(F), X B R, X A (R), X B (R)Raffinate out
E, X B (E), X C (E)S, X C(S)
Solvent Feed
Note that concentrationsof exiting streams from
an equilibrium stage are alwaysrelated by equilibrium.
B
7/30/2019 liqliq
8/24Lecture 7: Liquid-Liquid Ternary Single Stage8
The Extraction Factor
The degree of separation of the solute between the exiting streams is expressed as theextraction factor :
Extraction Factor : The ratio of solute flow inthe extract to solute flow in the raffinate.
E B X B E E C X B
E S
R B X B R
R A X B R
F A
BE B R B
X B E S
X B
R F A
Combining this definition with the equilibrium relationship:
results in another expression for the extraction factor :
B
E K D B
' X
B
R
B K D B
'S
F A
The larger the equilibriumdriving force to separate B, andthe larger the ratio of solvent tofeed, the larger the extraction
factor.
7/30/2019 liqliq
9/24Lecture 7: Liquid-Liquid Ternary Single Stage9
Extraction Efficiency
We can determine the amount not extracted starting with the material balance of the solute:
X B F
F A X B E
S X B R
F A
B F F A K D B
' X B
R S X B R F A
X B R
X B F
F A K D B
'S F A
And simplify:
This ratio gives the amountof solute left in the raffinateto the amount originally inthe feed stream,
The amount not extracted increaseswith the feed rate, and smaller ratio distribution between extractand raffinate and less solvent.
X B R
X B F
1 K D B
'S
F A1
1 B 1
We substitute in the K-value ratio:
7/30/2019 liqliq
10/24Lecture 7: Liquid-Liquid Ternary Single Stage
10
Ternary Phase Diagrams
A B
CIt is convenient to construct ternary phase diagrams on aGibbs Triangle (shown at right). Note that the variables
for these diagrams are only composition and that pressure and temperature are held constant (that is thatthese diagrams are slices through a four dimensionalspace with constant T and P).
7/30/2019 liqliq
11/24Lecture 7: Liquid-Liquid Ternary Single Stage
11
Ternary Phase Diagrams
A B
CCompositions are read as follows:Draw three lines from the composition
point parallel to the composition lines.Read the compositions off of the threeaxes.
Note: Only two mole fractions areneeded (use the third as a check).Compositions can be mole fractions
or mass fractions.
[94% C, 3% B, 3% A]
[20% C, 20% B, 60% A]
[100% A]
[33% C, 33% B, 33% A]
[30% C, 70% B]
7/30/2019 liqliq
12/24Lecture 7: Liquid-Liquid Ternary Single Stage
12
Construction of Ternary Phase Diagrams
G
7/30/2019 liqliq
13/24Lecture 7: Liquid-Liquid Ternary Single Stage
13
Ternary Eutectic Phase Diagrams
G
L
G
L
7/30/2019 liqliq
14/24Lecture 7: Liquid-Liquid Ternary Single Stage
14
Ternary Eutectic Phase Diagrams
A B
C
+
+
+
L
+ +L
+ +L
+ +L
+L +L
+L
T above T of theternary eutectic, but
below the binaryeutectics.
0 XB 1
+
L
+L
T
7/30/2019 liqliq
15/24Lecture 7: Liquid-Liquid Ternary Single Stage
15
Ternary Phase Diagrams
A B
C
L+L
7/30/2019 liqliq
16/24
Lecture 7: Liquid-Liquid Ternary Single Stage16
Partially Soluble Ternary Systems
If the two phases both have a partial solubility of the other component, then theanalysis is somewhat more complicated:
The difficulty is that now equilibrium data must be obtained for the ternarywhich relates the partial solubilities. Equilibrium data can be obtained graphically, or from tables. The ternary phase diagram is a typical way of representing the equilibriumcompositions of the two phases:
66% EthGly7% Furfural27 % Water A composition whereonly a single liquidexists.
17% EthGly27% Furfural56 % Water A composition wheretwo liquid phasescoexist.
50 % EthGly50% Furfural
100% Furfural
Solvent Carrier
Solute
Ethylene Glycol
Furfural
Water
7/30/2019 liqliq
17/24
Lecture 7: Liquid-Liquid Ternary Single Stage17
For two phase equilibrium (either complete insolubility, or partially solubility): the equilibrium is between two liquids phases ( = 2) three components (ternary) distribute between the two phases (C = 3)
For the static equilibrium case we can specify 3 variables:
If we specify T and P we are left with one additional variable:
Thus if we specify the concentration of one component in either of the phasesthis completely defines the state of the system.
Specification of Liquid-Liquid Equilibrium
Tie-Lines:Show the compositionsof the equilibrium phases.
Ethyl ene Glycol
Furfural
Water
7/30/2019 liqliq
18/24
Lecture 7: Liquid-Liquid Ternary Single Stage18
Partially Soluble Ternary Systems
Example: Consider a feed of 200 kg of 30% ethylene glycol in water. Add 300kg of purefurfural solvent.
Liquid Feed
Extract out
F, X A(F), X B R, X A (R), X B (R)Raffinate out E, X B (E), X C (E)
S, X C(S)
Solvent Feed
Ethylene Glycol
Furfural
Water
7/30/2019 liqliq
19/24
Lecture 7: Liquid-Liquid Ternary Single Stage19
Partially Soluble Ternary Systems
Example: Consider a feed of 200 kg of 30% ethylene glycol in water. Add 300kg of solventwhich is pure furfural.
Step 1: Locate the Solvent and Feed points
S300 Kg
F60 kg EG140 kg water
Ethylene Glycol
Furfural
Water
7/30/2019 liqliq
20/24
Lecture 7: Liquid-Liquid Ternary Single Stage20
Partially Soluble Ternary Systems
Step 2: Locate the mixing point M:
S 300 Kg
F 60 kg EG140 kg water
X B F F A X B
E S
F S
0.3 200kg 0 300kg
500kg 0. 12
Ethyl ene Glycol
Furfural
Water
M
7/30/2019 liqliq
21/24
Lecture 7: Liquid-Liquid Ternary Single Stage21
Partially Soluble Ternary Systems
Step 3: Use the tie-line to get the raffinate and extract compositions.
Extract (4% water, 14%EG, 82% furfural)
Raffinate (87% water, 5%EG, 8% furfural)
S 300 Kg
F 60 kg EG140 kg water
E R
Ethylene Glycol
Furfural
Water
M
7/30/2019 liqliq
22/24
Lecture 7: Liquid-Liquid Ternary Single Stage22
Partially Soluble Ternary Systems
Step 4: Determine the amount of extract and raffinate (can use lever rule)
R f
X C M X C
E
X C R X C E 0.63 0. 82
0.08 0.820.257 Extract (4% water, 14%EG, 82% furfural)
Raffinate (87% water, 5%EG, 8% furfural)
R 0.257 500kg 128 .4kg
E 1 0.257 500kg 371 .6kg
S 300 Kg
F 60 kg EG140 kg water
E R
Ethylene Glycol
Furfural
Water
M
7/30/2019 liqliq
23/24
Lecture 7: Liquid-Liquid Ternary Single Stage23
Partially Soluble Ternary Systems
Step 5: Determine the solvent free extract: Mixtures of E and S. Extend line from S throughE to solvent free point at H.
Solvent free extract H (20% water, 80% EG)
S 300 Kg
F 60 kg EG140 kg water
E R
Ethylene Glycol
Furfural
Water
M
H
X B
R
X B F
7/30/2019 liqliq
24/24
L 7 Li id Li id T Si l S24
Summary
This lecture covered: Ternary Liquid -Liquid extractions.
Ternary phase diagrams. A procedure to determine the product compositions and flow rates of a liquid-liquid extraction separation.
Next lecture will cover: Leaching Crystallization
Recommended