View
44
Download
11
Category
Preview:
Citation preview
Chapter C
Methodology for Calculating Coal Resources for the Colorado Plateau, U.S. Geological Survey National Coal Assessment
By Laura N.R. Roberts, 1 Michael E. Brownfield, 1Robert D. Hettinger,1 and Edward A. Johnson1
U.S. Geological Survey Professional Paper 1625–B*
U.S. Department of the InteriorU.S. Geological Survey
National CoalResourceAssessment
Click here to return to Disc 1 Volume Table of Contents
Chapter C ofGeologic Assessment of Coal in the Colorado Plateau:Arizona, Colorado, New Mexico, and UtahEdited by M.A. Kirschbaum, L.N.R. Roberts, and L.R.H. Biewick
1 U.S. Geological Survey, Denver, Colorado 80225
* This report, although in the USGS Professional Paper series,is available only on CD-ROM and is not available separately
Contents
Introduction .................................................................................................................................................C1Tools and Input .............................................................................................................................................. 4
Initial Step ............................................................................................................................................. 4Data ........................................................................................................................................................ 7Software .............................................................................................................................................. 10
Coal-Thickness Data .................................................................................................................................. 11Resource Polygons..................................................................................................................................... 15
Gridded Surfaces............................................................................................................................... 18Case Study 1: Southern Piceance Basin ....................................................................................... 19Case Study 2: Danforth Hills Coal Field .......................................................................................... 22
Resource Calculations .............................................................................................................................. 26Generating Resource Tables..................................................................................................................... 30Conclusions ................................................................................................................................................. 31References Cited ........................................................................................................................................ 31
Figures
1. Priority coal assessment units in the Colorado Plateau ......................................................C1 2. Flow chart for production of maps and coal resource tables............................................... 2 3. Priority coal assessment units of the Colorado Plateau and their
associated bounding rectangles ............................................................................................... 4 4. Geographic and cultural data within bounding rectangle..................................................... 5 5. Gridded and contoured data within bounding rectangle....................................................... 6 6. Example of interpreted geophysical log ................................................................................... 7 7. Geologic map of southern part of the Piceance Basin, northwestern Colorado............... 8 8. Example of shaded-relief topography generated from a digital elevation model ............. 9 9. Software packages used in the Colorado Plateau coal assessment
and their position within flow chart shown in figure 2 ......................................................... 10 10. Part of flow chart showing where coal-thickness data
were processed and verified.................................................................................................... 11 11. Example isopach map of net total coal using a regular contour interval,
Cameo/Wheeler coal zone, southern Piceance Basin, Colorado ...................................... 12 12. Example map of coal-thickness categories, C coal zone,
Yampa coal field, Colorado ....................................................................................................... 13 13. Hypothetical grid of net-coal thickness showing values at each grid node .................... 14 14. Example of the extent of bounding rectangle compared to
more detailed resource polygon .............................................................................................. 15
15. Example cross section showing position of coal zones stratigraphically above mappable marine sandstone units that are marker horizons ............................................. 16
16. Photograph of Trout Creek Sandstone Member of the Iles Formation, overlain by coal-bearing Williams Fork Formation, Yampa coal field, northwestern Colorado.............................................................................................................. 17
17. Structure contours on top of Rollins Sandstone Member, southern Piceance Basin, Colorado........................................................................................ 18
18. Diagrammatic stratigraphic column showing distribution of coal zones in Mesaverde Group or Mesaverde Formation, southern Piceance Basin .......................... 19
19. Cross-section view of surfaces of Rollins Sandstone Member and coal zones in Southern Piceance Basin assessment unit ....................................................................... 20
20. Map view of distribution of Rollins Sandstone Member and coal zones in Southern Piceance Basin assessment unit ........................................................................... 21
21. Overburden to top of the Trout Creek Sandstone Member, Danforth Hills coal field, northwestern, Colorado................................................................. 22
22. Generalized stratigraphic column of coal zones in Danforth Hills coal field showing average distance above Trout Creek Sandstone Member.................................. 23
23. Cross section and map view of the distribution of Trout Creek Sandstone Member and D coal zone, Danforth Hills coal field, northwestern Colorado................................... 24
24. Resource polygons generated using structural surface of Trout Creek Sandstone Member, average thickness of each coal zone, and digital elevation model, Danforth Hills coal field, Colorado ............................................................ 25
25. Part of flow chart showing where contour data are converted to ARC/INFO coverages............................................................................................................. 26
26. Individual polygon coverages unioned using ARC/INFO to create a coverage that was clipped with the resource polygon ......................................................................... 27
27. Final unioned polygon coverage created from union of all other polygon coverages that contain data for reporting coal-resource tonnage................................... 28
28. Part of flow chart showing where coal resources are calculated .................................... 29 29. Example output file from running volumetrics in EarthVision ............................................. 29 30. Example output file from running ‘evrpt’ program ................................................................ 29 31. Part of flow chart showing where coal resource tables are generated........................... 30 32. Example of table created in ArcView by joining output from ‘evrpt’
with attribute table of unioned polygon coverage................................................................ 30 33. Example of coal resource table generated using Pivot Table
function within Excel.................................................................................................................. 30
Methodology for Calculating Coal Resources for the Colorado Plateau, U.S. Geological Survey National Coal Assessment
By Laura N.R. Roberts, Michael E. Brownfi eld, Robert D. Hettinger, and Edward A. Johnson
Figure 1. Priority coal assessment units in the Colorado Plateau.
IntroductionThe coal assessment of the Colorado Plateau used four main crite-
ria for prioritizing assessment units within the region: (1) areas contain-ing signifi cant mineral ownership that are administered by the Federal Government, (2) areas that have active coal mining, (3) areas where coal-bed methane is currently being produced or coal is the source rock for gas production, and (4) areas that have a high resource or development potential.
The result of this endeavor is a detailed assessment of more than 20 coal zones in fi ve formations in the Colorado Plateau region (fi g. 1). This report describes the steps we used in an automated process to calculate coal resources and to produce the numerous accompanying maps for each assessment unit.
Coal-bearing strata
Study area
Priority assessment units
1. So. Wasatch Plateau2. Deserado3. Danforth Hills4. Yampa5. So. Piceance Basin6. San Juan Basin
1
2 34
5
6
113
113
34 34
4040
106
106
0 100 Miles
Colorado Plateau study area
UT CONMAZ
Assessment units referred to in this Chapter
C1
C2 Geologic Assessment of Coal in the Colorado Plateau: Arizona, Colorado, New Mexico, and Utah
We established an accurate, reliable, and time-effi cient method of combining an ASCII-formatted fi le containing location (x, y) and coal-thickness data with multiple layers of digital geologic and geographic data to ultimately arrive at high-quality end-products that show the distribution of coal resources (fi g. 2).
Figure 2. Flow chart for production of maps and coal resource tables.
Methods were also developed to defi ne areal limits of coal zones using a structural datum and a digital elevation model. As many as six commercially available software packages were used in conjunction with three custom programs to process the digital data. These programs range from simple conversion programs to highly sophisticated geographic information systems (GIS), two-dimensional geologic modeling programs, and spreadsheet software.
Plot contour maps, check data, revise database
(quality control)
Identify bounding rectangle to limit general area where
coal zones are to be assessed
BUnion coverages from A
and B into a single coverage and clip with
resource polygon C
Collect stratigraphic datafrom geophysical logs and
measured sections, and store in StratiFact database
convert-ism.aml
ARC/INFOStratiFact
ARC/INFO
evrpt
Excel
ArcView
Convert output from volumetrics report to table
of tonnage values and other information
Generate resource polygon
C
ismarc2
Import unioned coverageinto EarthVision
and run volumetrics
A Collect digital map data (geologic/geographic)
and generate ARC/INFO coverages
EarthVision
Data from StratiFactqueries imported into
EarthVision for calculating interpretive isopach and
structure maps
Join tonnage table with attributes of unioned polygon
coverage in ArcView - save as ASCII or .dbf file
Generate resource tables using 'Pivot table' in Excel
Convert contour data to digital coverages using ismarc and convert-ism.aml
EarthVision
Generate in EarthVision coal thickness grids to plot isopach
maps, create coal-thickness-category coverages and use in
coal-resource calculations
Methodology for Calculating Coal Resources for the Colorado Plateau, U.S. Geological Survey National Coal Assessment C3
Computer technology has it benefi ts and its shortcomings when it comes to representation of geologic data. In order to use a geographic information system, we create digital fi les that contain data that represent a mapped geologic unit or a well location (in projected map units) and record the x, y accuracy of that line or point to as many as 4 decimal places. We know that the x, y string representing that line is not accurate to that level. The data are only useful and reliable at the scale at which they were captured. Even then, care must be taken when using these digital data.
The benefi ts present themselves when we are asked to provide the best, most up-to-date estimate for coal tonnage for a particular coal zone in a particular area and, for example, for a particular overburden and coal-thickness category. We cannot provide a timely answer unless we have a database to query that contains all these parameters.
C4 Geologic Assessment of Coal in the Colorado Plateau: Arizona, Colorado, New Mexico, and Utah
Tools and InputA study of such scope as the coal assessment of the Colorado
Plateau required a plan that could be followed step-by-step, data for input, and tools to manipulate and process the data.
Figure 3. Priority coal assessment units of the Colorado Plateau and their associated bounding rectangles. The top part of the fl ow chart shown in fi gure 2 is also shown. In discussing this and following fl ow charts, the relevant part(s) of the fl ow chart will be shown clearly as on fi gure 2, but nearby boxes that are not relevant to the discussion will be grayed-out.
The initial purpose for identifying the bound-ing rectangle was that it limited our search for stratigraphic data to include in the database.
Initial Step
After the study areas or assessment units of the Colorado Plateau were priori-tized, based on the four main criteria, the next step was to identify a rectangular box slightly larger than each of the areas to be assessed (fi g. 3). The size and location of the rectangle was based on our preliminary knowledge of the coal geology in each area.
Bounding rectangle
1
23
4
5
6
113
113
40
106
106
0 50 Miles
Colorado Plateau study area (part)
UT
AZ
CO
NM
Coal-bearing strata
Study area
Priority assessment units
1. So. Wasatch Plateau2. Deserado3. Danforth Hills4. Yampa5. So. Piceance Basin6. San Juan Basin
40 Assessment units referred to in this chapter
Plot contour maps, check data, revise database
(quality control)
Identify bounding rectangle to limit general area where
coal zones are to be assessed
BUnion coverages from A
and B into a single coverage and clip with
resource polygon C
Collect stratigraphic datafrom geophysical logs and
measured sections, and store in StratiFact1 database
convert-ism.aml2
ARC/INFO1StratiFact1
ARC/INFO1
evrpt2
Excel1
ArcView1
Convert output from volumetrics report to table
of tonnage values and other information
Generate resource polygon
C
EarthVision1
ismarc2
Import unioned coverageinto EarthVision1Run volumetrics
Collect digital map data (geologic/geographic)
and generate ARC/INFO1 coverages
Calculate interpretive mapsfrom queries of StratiFact1
database (isopachs, structure, etc.)
Join tonnage table with attributes of unioned polygon
coverage in ArcView1 - save as ASCII or .dbf file
Generate resource tables using 'Pivot table' in Excel1
Convert contour data to digital coverages using
ismarc2 and convert-ism.aml2
Generate coal thickness grid to plot isopach maps, to
create coal-thickness-category coverages and to use in
coal resource calculations
EarthVision1
Methodology for Calculating Coal Resources for the Colorado Plateau, U.S. Geological Survey National Coal Assessment C5
The maximum and minimum x and y values of this “bounding rectangle” were used to clip data collected from sources at national, State, and regional scales. These data include such coverages as roads, counties, public land survey systems (township and range), hydrology, quadrangles, surface and mineral ownership (fi g. 4), and geology. For the most part, these data were retrieved from internet sites.
Figure 4. Geographic and cultural data within the bounding rectangle. Example from Deserado coal assessment unit, northwestern Colorado.
Geographic and Cultural Maps
BOUNDING RECTANGLE
����
�
���
���
�
���
���
���
�
���
���
���
���
�
���
���
���
���
��
���
���
���
���
�
���
���
���
���
��
���
���
���
���
��
���
���
���
���
��
���
���
���
���
���
���
���
���
������
Counties
Surface ownership
Coal ownership
7.5' quadrangles
Townships
Lease area
Federal
State and private
C6 Geologic Assessment of Coal in the Colorado Plateau: Arizona, Colorado, New Mexico, and Utah
Ultimately, the bounding rectangle was used to limit gridding and contouring of data that resulted in interpretive maps. These data include net-coal thickness, coal-zone thickness, overburden thickness for isopach maps (fi g. 5), and elevations on the top of a structural datum for structure contour maps.
Figure 5. Gridded and contoured data within the bounding rectangle. Examples from Deserado coal assessment unit, Lower White River coal fi eld, northwestern Colorado.
BOUNDING RECTANGLE
Overburden categories (ft)
< 500
500 - 1000
1000 - 1500
> 1500
< 1.21.2 - 2.32.3 - 3.53.5 - 77 - 14> 14
Coal-thickness categories (ft)
1.2 1.2
14
2.3
2.3
2.3
2.3
2.3
3.5 3.5
3.5
3.57
7
77
information not shownfor lease area
Interpretative Maps
Methodology for Calculating Coal Resources for the Colorado Plateau, U.S. Geological Survey National Coal Assessment C7
Data
The main sources of stratigraphic data are geo-physical logs of holes drilled for coal (fi g. 6), oil, and gas exploration and descriptions of stratigraphic sec-tions measured in the fi eld.
Figure 6. Example of interpreted geophysical log, Yampa coal fi eld, northwestern Colorado. Modifi ed from Johnson and others (chap. P, this CD-ROM).
Natural Gamma
Density
A coal zone
Trout Creek SandstoneMember
0
100 ft
Vertical scale
50
Coal
Sandstone
C8 Geologic Assessment of Coal in the Colorado Plateau: Arizona, Colorado, New Mexico, and Utah
Geologic information consisted mainly of published geologic maps that were either available digitally or were digitized in-house from published maps (fi g. 7).
Figure 7. Geologic map of southern part of the Piceance Basin, northwestern Colorado. Modifi ed from the digital geologic map of Colorado (Green, 1992). Illustration from Hettinger and others (chap. O, this CD-ROM).
COLORADO
southern part of the
Piceance Basin many faults
many faults
10 0 10 Miles
DELTA
MESA
GARFIELD
RIO
BLANCO
GUNNISON
PITKIN
15 S
14 S
13 S
11 S
10 S
9 S
8 S
6 S
7 S
2 N
1 N
2 E
3 E
5 S
4 S
8687 85 W8889 90
90 W 91
92103104 W 102 101 93 94 95 96 97 98 99100
91 W
104 W 103
95 94 93 92 W 96 W
98 99 W100 W
1 E1 W 2 W3 W
1 S
2 S
3 S
4 S
UTA
H
CO
LO
RA
DO
39 45'o109o 108o
39 o39 o
109o
PaoniaCrestedButte
Grand Junction
Glenwood Springs
SYNCLINE
FAULT--Bar and ball on downthrown side.
Explanation
Qs Surficial deposits (Holocene and Pleistocene)
Tug Uinta and Green River Formations (Eocene)
Te Extrusive igneous rocks (Miocene and Oligocene)
Ti Intrusive igneous rocks (Miocene and Oligocene)
Km Mancos Shale (Cretaceous)
ANTICLINE
MONOCLINE
THRUST FAULT--Sawteeth on upper plate.
KCr Rocks older than the Mancos Shale (Cretaceous, Jurassic, Triassic, Permian, Pennsylvanian, Mississippian, Devonian, Ordovician, and Cambrian)
Kmv Mesaverde Group and Mesaverde Formation (Cretaceous).
Tw Wasatch (Paleocene and Eocene). The map unit, as compiled by Tweto (1979), may include strata in the upper part of the Ohio Creek Formation (R.C. Johnson, personal commun., 1999).
Methodology for Calculating Coal Resources for the Colorado Plateau, U.S. Geological Survey National Coal Assessment C9
Digital elevation models (DEM’s) were used to represent topography of the Earth’s surface (fi g. 8). These models are available at different scales from the USGS Global Land Information System (see website at http://edc.usgs.gov/webglis). We used these data to generate polygons for the resource areas, overburden isopach maps, and polygons that defi ne overburden categories for the assessed coal zones.
Figure 8. Example of shaded-relief topography generated from a digital elevation model (DEM), Danforth Hills coal fi eld, northwestern Colorado.
C10 Geologic Assessment of Coal in the Colorado Plateau: Arizona, Colorado, New Mexico, and Utah
Software
Stratigraphic data were entered into a rela-tional database software package specifi cally designed for these kinds of data (StratiFact, Gal-legos Research Group, Inc.). The querying and fi ltering capabilities of StratiFact allow for the output of ASCII-format fi les that contain infor-mation that can be imported into a two-dimen-sional modeling software package. These fi les contain data for location (x and y fi elds) and such data as net-coal thickness, elevation to top and (or) base of key horizons, and thickness of coal-bearing intervals.
Figure 9. Software packages used in the Colorado Plateau coal assessment and their position within the fl ow chart shown in fi gure 2.
We also used the vector-based GIS ARC/INFO (ESRI, 1998a) for storing polygon coverages.
We used three custom programs to convert contour lines generated from grids in EarthVision to ARC/INFO polygon coverages. Details of the conversion process are documented in previous reports (Roberts and Biewick, 1999; Roberts and others, 1998). ArcView (ESRI, 1998b) was used for desktop mapping, data verifi cation, and fi nal data-table generation, and Microsoft Excel (Microsoft Corporation, 1997) was used to store coal tonnage fi gures and to create resource tables.
EarthVision (Dynamic Graphics, Inc., 1997) was used to generate interpretive maps by gridding and contouring data extracted from StratiFact queries (fi g. 2) and for calculating coal resource estimates. The capabilities within EarthVision to perform mathematical functions on grids and to plot and save virtually any contour line as an ASCII string of coordi-nates from a grid were used extensively.
Plot contour maps, check data, revise database
(quality control)
Identify bounding rectangle to limit general area where
coal zones are to be assessed
Union coverages from A and B into a single
coverage and clip with resource polygon C
Collect stratigraphic datafrom geophysical logs and
measured sections, and store in StratiFact1 database
convert-ism.aml2
ARC/INFO1StratiFact1
2 Custom program
1 Commercial software
ARC/INFO1
evrpt2
Excel1
ArcView1
Convert output from volumetrics report to table
of tonnage values and other information
Generate resource polygon
ismarc2
Import unioned coverageinto EarthVision1Run volumetrics
A Collect digital map data (geologic/geographic)
and generate ARC/INFO1 coverages
Join tonnage table with attributes of unioned polygon
coverage in ArcView1 - save as ASCII or .dbf file
Generate resource tables using 'Pivot table' in Excel1
Convert contour data to digital coverages using
ismarc2 and convert-ism.aml2
EarthVision
Data from StratiFactqueries imported into
EarthVision for calculating interpretive isopach and
structure maps
EarthVision
Generate in EarthVision coal thickness grids to plot isopach
maps, create coal-thickness-category coverages and use in
coal-resource calculations
Methodology for Calculating Coal Resources for the Colorado Plateau, U.S. Geological Survey National Coal Assessment C11
Coal-Thickness DataCoal-tonnage estimates were calculated by multiplying coal thickness
by area by the average weight of bituminous-rank coal (short tons per acre-foot; Wood and others, 1983). Data related to coal thickness and area must be as accurate as possible (fi g. 10). A discussion of how the thickness data were derived, what they represent, and how they were used in the fi nal reporting of coal resources follows.
Figure 10. Part of fl ow chart (fi g. 2) showing where coal-thickness data were processed and verifi ed.
Plot contour maps, check data, revise database
(quality control)
Identify bounding rectangle to limit general area where
coal zones are to be assessed
Collect stratigraphic datafrom geophysical logs and
measured sections, and store in StratiFact database
convert-ism.aml2
ARC/INFO1StratiFact
ismarc2
A Collect digital map data (geologic/geographic)
and generate ARC/INFO1 coverages
EarthVision
Data from StratiFactqueries imported into
EarthVision for calculating interpretive isopach and
structure maps
EarthVision
Generate in EarthVision coal thickness grids to plot isopach
maps, create coal-thickness-category coverages and use in
coal-resource calculations
C12 Geologic Assessment of Coal in the Colorado Plateau: Arizona, Colorado, New Mexico, and Utah
We used 1.0 or 1.2 ft as a minimum thickness for resource consideration based on a modification of the coal-bed-thickness criteria for bituminous coal (Wood and others, 1983). An ASCII-formatted fi le was created from a query of the StratiFact database containing the x, y values for location at each data point and a value for the net thickness of coal for the coal zone. The data were imported into EarthVision as a scattered data fi le. The data were gridded using the x, y limits of the bounding rectangle.
Figure 11. Example isopach map of net total coal using a regular contour interval, Cameo/Wheeler coal zone, southern Piceance Basin, Colorado.
The coal isopach grid has several functions. First, the grid was contoured with a regular contour interval for displaying a coal isopach map (fi g. 11). Plot-ting an isopach map often reveals problems with the data or errors in interpretation and is therefore valuable for quality control. Sev-eral iterations of the gridding and contouring process were some-times required.
10 0 10 Miles
39 45'
39 30'
39
108 107 30'108 30'109
0-20
Total net thickness of coal
20-4040-6060-80>80
Methodology for Calculating Coal Resources for the Colorado Plateau, U.S. Geological Survey National Coal Assessment C13
Second, the fi nal coal-thickness grid was contoured with an irregular contour interval (fi g. 12)—that is, only those contours that represent the boundaries of net-coal-thickness categories for bituminous coal, which are the 1.2-ft, 2.3-ft, 3.5-ft, 7.0-ft and 14-ft contour lines (Wood and others, 1983). The lines eventually became polygon boundaries for the ARC/INFO coverage of coal-thickness categories, which is one of the parameters for reporting coal resource estimates.
Figure 12. Example map of coal-thickness categories, C coal zone, Yampa coal fi eld, Colorado.
Coal-thickness categories (ft)
1.2 - 2.32.3 - 3.53.5 - 77 - 14> 14
40 37' 30''
40 30'
107 30'107 45'
0 5 Miles
C14 Geologic Assessment of Coal in the Colorado Plateau: Arizona, Colorado, New Mexico, and Utah
Finally, the coal-thickness grid was used in the process of calculating coal volume and tonnage in EarthVision. The thickness values of the grid nodes, from the two-dimensional grid of coal thickness (fi g. 13), supplied the thickness values used to calculate the coal tonnage within each polygon.
Figure 13. Hypothetical grid of net-coal thickness showing values at each grid node.
Methodology for Calculating Coal Resources for the Colorado Plateau, U.S. Geological Survey National Coal Assessment C15
Resource PolygonsIn addition to data related to coal thickness, data
related to the area within which resources are to be calcu-lated are very important. This area is referred to as a resource polygon. The resource polygon differs from the bounding rectangle, discussed earlier in this report, in that it more accurately depicts the areal distribution of the coal zone (fi g. 14).
Figure 14. Example of the extent of the bounding rectangle compared to the more detailed resource polygon. Shaded-relief topography of Danforth Hills coal fi eld in the background, northwestern Colorado.
Many factors were used to defi ne the boundaries for the resource-polygon areas. A few examples include: (1) areas where the coal zone is exposed at the surface, (2) areas where the coal is too thin or too deep to qualify as a resource using criteria of Wood and others (1983), and (3) areas where data are too sparse to adequately assess the coal zone. Resource polygons are the single most important polygons because they limit the resource. They may also be the most diffi cult to create, especially in the case where a large part of the boundary is defi ned by where the coal zone is exposed at the surface.
BOUNDING RECTANGLE
RESOURCE POLYGON
C16 Geologic Assessment of Coal in the Colorado Plateau: Arizona, Colorado, New Mexico, and Utah
Many of the coal zones that were assessed in the Colorado Plateau are directly above recognizable marker horizons (i.e., marine sandstone units) that can be mapped on the surface and, because of a fairly dis-tinctive geophysical log signature, can also be mapped in the subsurface (fi g. 15).
Figure 15. Example cross section showing position of coal zones stratigraphically above mappable marine sandstone units that are the marker horizons. Modifi ed from Johnson and others (chap. P, this CD-ROM).
100500
100500
100500
100500
100500
Twentymile
Big White
NG
D
Natural Gamma
Density
NG D
NG D
NG D
NG D NG D
2.5 mi 2.5 mi 3.1 mi 2.0 mi
Barren interval
Coal zone
Coal
Mappable marine sandstone
0
100 ft
50
Cross section scales
2.5 mi
Horizontal distance in miles between drill holes
Methodology for Calculating Coal Resources for the Colorado Plateau, U.S. Geological Survey National Coal Assessment C17
Digitized lines representing the exposures of the top of these marker horizons (i.e., the Pictured Cliffs Sandstone in the San Juan Basin, the Star Point Sandstone in the southern Wasatch Plateau, and the Trout Creek Sandstone Member of the Iles Formation in the Yampa coal fi eld (fi g. 16)) were used to partially defi ne the resource polygon for the overlying coal zones (i.e., the Fruitland Formation, lower Blackhawk Formation, and Williams Fork Formation, respectively).
Figure 16. Cliffs are the Trout Creek Sandstone Member of the Iles Formation, which is overlain by the coal-bearing Williams Fork Formation, Yampa coal fi eld, northwestern Colorado. Photograph by E.A. Johnson, 1978.
A problem arises in cases where a coal zone to be assessed has not been mapped on the surface and is not associated with a distinct marker horizon. In these cases, the location of the pseudo-outcrop must be estimated using innovative techniques. A description of some tools and techniques used to generate these pseudo-outcrops is provided in the following section along with two case studies.
C18 Geologic Assessment of Coal in the Colorado Plateau: Arizona, Colorado, New Mexico, and Utah
Gridded Surfaces
Initially, two grids are generated in EarthVision, each of which represents a surface. One is a grid of a digital elevation model (DEM) that represents the surface topography in the study area. The other is a grid that represents a structural datum, such as the top of a mappable marine sandstone unit. From a query of the StratiFact database, a fi le is generated that contains fi elds for location (x and y) and eleva-tion of the structural datum (for example, the Rollins Sandstone in the southern Piceance Basin; fi g. 17).
Figure 17. Structure contours on top of the Rollins Sandstone Member, southern Piceance Basin, Colorado.
Information on the elevation of this datum from other sources, such as outcrop measurements or published structure contour maps, is added to the drill-hole data in order to provide as much control as possible, especially where the structural datum is exposed at the surface. All of these data are gridded in EarthVision to create a two-dimensional grid fi le that represents the surface on the structural datum. Structure contours are then plotted from this grid fi le. The best possible representation of this surface on top of the structural datum is critical because additional surfaces are generated from it.
10 0 10 Miles
39 45'
39 45'
39
108 107 30'108 30'109
7000
6000
6000
5000
6000
6000
6000
4000
3000
2000
2000
1000
0
-1000
-2000
-2000-3000
-4000
6000
6000
7000
8000
9000 1000
0
Methodology for Calculating Coal Resources for the Colorado Plateau, U.S. Geological Survey National Coal Assessment C19
Case Study 1: Southern Piceance Basin
To create resource polygons for the coal zones assessed in the southern Piceance Basin (fi g. 1), we combined a grid of thickness with a structure contour grid of the top of the Rollins Sandstone Member to generate pseudo-outcrops.
Figure 18. Diagrammatic stratigraphic column showing distribution of coal zones in the Mesaverde Group or Mesaverde Formation, southern Piceance Basin.
In this case study, a data set was extracted from StratiFact that contains x, y, z data, where z is the thickness between the top of the Rollins (a good marker horizon in this area) (fi g. 18) and the base of the overlying South Canyon coal zone.
Top of Rollins Sandstone Member (mappable sandstone unit)
Base of Cameo/Wheeler coal zone
Base of South Canyon coal zone
Base of Coal Ridge coal zone
Mes
aver
de G
roup
(pa
rt)
or F
orm
atio
n (p
art)
C20 Geologic Assessment of Coal in the Colorado Plateau: Arizona, Colorado, New Mexico, and Utah
These thickness data were gridded and then, using the ‘Formula Processor’ utility in EarthVision, the resultant thickness grid was added to the grid of the structural surface on the top of the Rollins Sandstone Member. The resulting grid is a pseudo-structure grid on the base of the South Canyon coal zone (fi g. 19).
Figure 19. Cross-section view of surfaces of Rollins Sandstone Member and coal zones in the Southern Piceance Basin assessment unit. Location of cross section B-B′ is shown on fi g. 20.
10,000
-2,000
5,000
0
0 10,000 20,000 30,000 40,000 50,000
B B'
Elevation (ft) abovemean sea level
Distance (meters)
Overburden to base of Coal Ridge coal zone
Overburden to base of South Canyon coal zone
Overburden to top of Rollins
Outcrop of top of Rollins
Pseudo-outcrop of base of South Canyon Pseudo-outcrop of base of
Coal Ridge
Vertical exageration approximately x 3
Surface from DEM
Cameo/Wheeler coal zone
Pseudo-structural surface,base of South Canyon Pseudo-structural surface,
base of Coal Ridge
Methodology for Calculating Coal Resources for the Colorado Plateau, U.S. Geological Survey National Coal Assessment C21
This pseudo-structure grid on the base of the South Canyon coal zone was then subtracted from the DEM grid of topography, resulting in a grid of overburden thickness to the base of the coal zone. The zero overburden line generated from this grid represents the pseudo-outcrop line for the base of the South Canyon coal zone and defi nes the areal limits of the coal zone, at least along the northeastern and southern parts of the area (fi g. 20). The western limit of the area is represented by a line where the net-coal thickness becomes less than 1.2 ft.
Figure 20. Map view of distribution of Rollins Sandstone Member and coal zones in the Southern Piceance Basin assessment unit.
The polygon defi ning the areal limits of the overlying Coal Ridge coal zone (fi g. 21) was generated by adding the thickness grid of the South Canyon coal zone to the pseudo-structure on the base of the South Canyon coal zone and subtracting that resultant grid from the DEM topography. Again, the zero overburden line generated from this fi nal grid represents the pseudo-outcrop line for the base of the Coal Ridge coal zone and partially defi nes the areal limits of this coal zone.
39
108108 30'109
B
B'
Outcrop, top of Rollins
Areal distribution ofSouth Canyon coal zone
Areal distribution ofCameo/Wheeler coal zone
Pseudo-outcrop, base of Coal Ridge coal zone
0 20 Miles
B'see
Dashed portion of resource polygons for Coal Ridge and South Canyon coal zones indicate where net coal thinsto less than 1.2' thick detail
COLORADO
southern part of the
Piceance Basin
Teriary intrusives
C22 Geologic Assessment of Coal in the Colorado Plateau: Arizona, Colorado, New Mexico, and Utah
Case Study 2: Danforth Hills Coal Field
In this case, it was impossible to use grids of coal-zone thickness added to the top of the structural datum to create pseudo-structure grids and overburden grids because, in the Danforth Hills coal fi eld, seven coal zones stratigraphically overlie the structural datum (the Trout Creek Sandstone Member of the Iles Formation) and the interval between the base of each successively higher coal zone is not very thick—in all cases less than 300 ft. The irregular distribution of coal-zone-thickness data precluded generating coal-zone isopach grids that, when added to the structural datum, would adequately represent a surface. When we tried the method used for the southern Piceance Basin, the result was computer-generated (pseudo) outcrop lines of the coal zones that, when plotted simultaneously, would cross each other in several places.
Figure 21. Overburden to top of the Trout Creek Sandstone Member, Danforth Hills coal fi eld, northwestern, Colorado.
Using the ‘Formula Processor’ utility in EarthVision, we created a grid of overburden thickness by subtracting the gridded surface of the top of the Trout Creek Sandstone Member (structural datum) from the gridded surface of the topography. This resultant grid represents the thickness between the two surfaces—in other words, the thickness of overburden to the top of the Trout Creek. Once the grid of overburden thickness was calculated, an overburden isopach map was generated depicting the lines of equal overburden thickness above the Trout Creek (fi g. 21).
0 5 Miles
Outcrop, top of Trout Creek Sandstone Member
0-500500-10001000-20002000-30003000-6000
Overburden categories(in feet)
Methodology for Calculating Coal Resources for the Colorado Plateau, U.S. Geological Survey National Coal Assessment C23
From a query of the StratiFact database, we then calculated the average distance (in feet) above the top of the Trout Creek Sandstone Member to the base of each of six coal zones (fi g. 22).
Figure 22. Generalized stratigraphic column of coal zones in the Danforth Hills coal fi eld showing average distance (in ft) above the Trout Creek Sandstone Member.
1050
970
760
480
350
240
130
Base of C coal zone
Base of B coal zone
Base of D coal zone
Base of E coal zone
Base of F coal zone
Base of G coal zone
Base of A coal zone
Average distance (in ft) above the
Trout Creek Sandstone Member
Will
iam
s Fo
rk F
orm
atio
n (p
art)
(mappable marine sandstone unit)Top of Trout Creek Sandstone Member-
C24 Geologic Assessment of Coal in the Colorado Plateau: Arizona, Colorado, New Mexico, and Utah
For example, the stratigraphic distance above the top of the Trout Creek to the base of the D coal zone is, on average, 350 ft. Because this stratigraphic distance is equivalent to the average thickness of rock lying between the coal zone and the top of the Trout Creek, we can also interpret that, on average, 350 ft of overbur-den would separate the base of the D coal zone from the Trout Creek.
Figure 23. Cross section and map view of the distribution of the Trout Creek Sandstone Member and the D coal zone, Danforth Hills coal fi eld, northwestern Colorado.
By this reasoning, we also interpreted that the D coal zone is only present in areas of the coal fi eld where overburden to the top of the Trout Creek would be equal to or greater than 350 ft. Therefore, the 350-ft overburden line was used to defi ne the maxi-mum areal extent of the D coal zone and, thus, was considered as a pseudo-outcrop line (in map view) for the D coal zone (fi g. 23).
0 5 Miles
Outcrop, top of Trout CreekSandstone
Top of Trout
base of D coal zone
A
A'
Areal distribution of D coal zone = Resource polygon for D coal zone
Area where Trout Creek and D coal zone are eroded
Area where overburden to top of Trout Creek is less than 350 ft
SandstoneCreek
350-ft overburden line totop of Trout Creek Sandstone
and 'pseudo' outcrop of
8400
8000
7600
7200
6800
6400
6000
5600
5200
0 2000 4000 6000 8000 16000140001200010000 2000018000
Top of Trout CreekSandstone
Outcrop of top of Trout Creek Sandstone
A A'
base of D coal zone
350-ft overburden line totop of Trout Creek Sandstone
Surface topography from Digital Elevation Models
and 'pseudo' outcrop of
350 ft
Base of D coal zone
Methodology for Calculating Coal Resources for the Colorado Plateau, U.S. Geological Survey National Coal Assessment C25
Through this process, pseudo-outcrop lines for each coal zone can be generated using the combination of the overburden map to the top of the Trout Creek and the average stratigraphic distance above the Trout Creek to the base of every overlying coal zone. Because the base of the B coal zone is only 130 ft, on average, above the top of the Trout Creek Sandstone, we used the line representing the Trout Creek Sandstone to also represent the boundary of the area underlain by the B coal zone. Note how, from map to map, the areal distribution of each successively higher coal zone is reduced (fi g. 24).
Figure 24. Resource polygons generated using structural surface of the Trout Creek Sandstone Member, the average thickness of each coal zone, and a digital elevation model, Danforth Hills coal fi eld, Colorado.
A and B coal zones
C coal zone
D coal zone
E coal zone
F coal zone
G coal zone
Resource polygons
C26 Geologic Assessment of Coal in the Colorado Plateau: Arizona, Colorado, New Mexico, and Utah
Resource CalculationsThe results of the procedures discussed so far are net-coal-thickness grids and resource polygons that were used in the fi nal
steps of coal-resource calculations. The Deserado assessment area, Lower White River coal fi eld (fi g. 1), is used as an example for the following discussion of calculating resources.
Figure 25. Part of fl ow chart (fi g. 2) showing where contour data are converted to ARC/INFO coverages.
Once satisfi ed with the pseudo-outcrop line (zero overburden line), any other associated overburden lines and coal isopach lines, data were saved in ASCII format as a ‘contour output fi le,’ which is one of the EarthVision plotting options. The program ‘ismarc’ was then used to convert the contour output fi le from EarthVi-sion to a fi le that is in ‘arc-generate’ format. The output fi le from ‘ismarc’ was then processed in ARC/INFO using an Arc Macro Language (AML) program (convert-ism.aml) that con-verted it into an ARC/INFO polygon coverage (fi g. 25). Both ‘ismarc’ and ‘convert-ism’ were provided by the Illinois State Geological Survey.
Plot contour maps, check data, revise database
(quality control)
Identify bounding rectangle to limit general area where
coal zones are to be assessed
BU
c
Collect stratigraphic datafrom geophysical logs and
measured sections, and store in StratiFact1 database
convert-ism.aml
StratiFact1
Generate resource polygon
C
ismarc
A Cdata
AR
Convert contour data to digital coverages using ismarc and convert-ism.aml
EarthVision
Data from StratiFactqueries imported into
EarthVision for calculating interpretive isopach and
structure maps
EarthVision
Generate in EarthVision coal thickness grids to plot isopach
maps, create coal-thickness-category coverages and use in
coal-resource calculations
Methodology for Calculating Coal Resources for the Colorado Plateau, U.S. Geological Survey National Coal Assessment C27
Using ARC/INFO, a single polygon coverage was created that is the union of all polygon coverages for which tonnages were reported (fi g. 26), such as county, quadrangle, township, surface and coal ownership, and overburden- and coal-thickness categories.
Figure 26. Individual polygon coverages were all unioned using ARC/INFO to create a coverage that was clipped with the resource polygon.
BOUNDING RECTANGLE
BOUNDING RECTANGLE
Interpretive Maps Geographic and Cultural Maps
BOUNDING RECTANGLE
����
�
���
���
�
���
���
���
�
���
���
���
���
�
���
���
���
���
��
���
���
���
���
�
���
���
���
���
��
���
���
���
���
��
���
���
���
���
��
���
���
���
���
���
���
���
���
������
Counties
Surface ownership
Coal ownership
7.5' quadrangles
Townships
Lease area
Federal
State and private
Overburden categories (ft)
< 500500 - 10001000 - 1500> 1500
< 1.21.2 - 2.32.3 - 3.53.5 - 77 - 14
information not shownfor lease area
> 14
Coal-thickness categories (ft)
1.2 1.2
14
2.3
2.3
2.3
2.3
2.3
3.5 3.5
3.5
3.57
7
77
information not shownfor lease area
C28 Geologic Assessment of Coal in the Colorado Plateau: Arizona, Colorado, New Mexico, and Utah
As a fi nal step before resources were calculated, this polygon coverage was clipped by the resource polygon using the ‘identity’ command in ARC/INFO (fi g. 27). This fi nal polygon coverage was imported into EarthVision as a single polygon fi le. Although several attributes are associated with the individual polygons that make up the unioned polygon, the user is allowed to label only one attribute when importing the unioned polygon. The ‘coverage-id’ attribute must be used to label the individual polygons within the unioned polygon because it is a unique identifi er for each polygon.
Figure 27. Final unioned polygon coverage created from the union of all other polygon coverages that contain data for reporting coal-resource tonnage. Also shown is part of the fl ow chart (fi g. 2) where the fi nal unioned polygon was generated and imported into EarthVision.
Resource polygon
Final unioned polygon
BOUNDING RECTANGLE
Union coverages from A and B into a single
coverage and clip with resource polygon C
ARC/INFO
Plot contour maps, check data, revise database
(quality control)
Identify bounding rectangle to limit general area where
coal zones are to be assessed
Collect stratigraphic datafrom geophysical logs and
measured sections, and store in StratiFact database
ARC/INFOStratiFact
evrpt
Excel
ArcView
Convert output from volumetrics report to table
of tonnage values and other information
EarthVision
Calculate interpretive mapsfrom queries of StratiFact
database (isopachs, structure, etc.)
Join tonnage table with attributes of unioned polygon
coverage in ArcView - save as ASCII or .dbf file
Generate resource tables using 'Pivot table' in Excel
Generate coal thickness grid to plot isopach maps, to
create coal thickness category coverages and to use in
coal resource calculations
convert-ism.aml
ismarc
Import unioned coverageinto EarthVision
and run volumetrics
EarthVision
B
Generate resource polygon
C
A Collect digital map data (geologic/geographic)
and generate ARC/INFO coverages
Convert contour data to digital coverages using ismarc and convert-ism.aml
Methodology for Calculating Coal Resources for the Colorado Plateau, U.S. Geological Survey National Coal Assessment C29
The volumetrics utility within EarthVision was used to calculate short tons of coal (fi g. 28). The grid of net-coal thickness supplied the thickness values used to calculate coal tonnage within each polygon.
Figure 28. Part of fl ow chart (fi g. 2) showing where coal resources are calculated.
Figure 29. Example output fi le from running volumet-rics in EarthVision.
Figure 30. Example output fi le from running ‘evrpt’ program.
The resultant output fi le from the ‘evrpt’ pro-gram was imported into ArcView as a table.
A program was written by the USGS called ‘evrpt’ that converts this volumetrics report to a tab-delimited ASCII-formatted fi le. The ‘evrpt’ program strips the header information from the volumetrics report and calcu-lates the average coal thickness for each polygon that EarthVision used to calculate the short-ton value (fi g. 30).
The result of running the volumetrics routine is an ASCII-formatted fi le (volumetrics report) that lists by polygon-id (same as coverage-id) a value for area and short tons for each polygon within the polygon fi le (fi g. 29).
evrpt
ArcView
Convert output from volumetrics report to table
of tonnage values and other information
Import unioned coverageinto EarthVision
and run volumetrics
Join tonnage table with attributes of unioned polygon
coverage in ArcView - save as ASCII or .dbf file
Union coverages from A and B into a single
coverage and clip with resource polygon C
ARC/INFO1
Excel1
Generate resource tables using 'Pivot table' in Excel1
B
convert-ism.aml2
ismarc2
Convert contour data to digital coverages using
ismarc2 and convert-ism.aml2
1 125,153 102,750 125,153 2 10,460 10,366 10,460 3 1,662,359 1,310,989 1,662,359 4 1,180,221 1,483,251 1,180,221
Polygon ID Area Short_tons Positive Area
ID Short_tons Positive EVthk
1 102750 125153 1.8 2 10367 10460 2.2 3 1310989 1662359 1.8 4 1483251 1180221 2.8
C30 Geologic Assessment of Coal in the Colorado Plateau: Arizona, Colorado, New Mexico, and Utah
Generating Resource Tables
Figure 31. Part of fl ow chart (fi g. 2) showing where coal resource tables are generated.
Figure 32. Example of table created in ArcView by joining output from ‘evrpt’ with attribute table of the unioned polygon coverage. Item used to join the tables is the ‘polygon-id.’
Figure 33. Example of coal resource table generated using the Pivot Table function within Excel. Data are from table in fi gure 32.
Once in Excel, the ‘Pivot Table’ util-ity was used to create tables that report resource estimates using any category in the spreadsheet (fi g. 33).
In ArcView, the table was joined to the attribute table of the ARC/INFO unioned polygon coverage (fi g. 31) using the ‘polygon-id’ (EarthVision) and ‘coverage-id’ (ARC/INFO). The result of joining the two tables is a new table with a record that contains a short-tons value for every polygon in the unioned polygon (fi g. 32). The joined table was exported from ArcView as a delimited ASCII fi le or a standard database fi le (.dbf) and read directly into a spreadsheet program such as Microsoft Excel.
Excel
Join tonnage table with attributes of unioned polygon
coverage in ArcView - save as ASCII or .dbf file
Generate resource tables using 'Pivot table' in Excel
B
convert-ism.aml2
ismarc2
Convert contour data to digital coverages using
ismarc2 and convert-ism.aml2
evrpt
ArcView
Convert output from volumetrics report to table
of tonnage values and other information
Import unioned coverageinto EarthVision
and run volumetrics
125153 1 1.2-2.3 0-500 BLM All Rangely NE Moffat T3N R102W 102750 125153 1.8 102 10461 2 1.2-2.3 0-500 BLM All Rangely NE Moffat T3N R102W 10367 10460 2.2 101662360 3 1.2-2.3 0-500 BLM All Rangely NE Moffat T3N R102W 1310989 1662359 1.8 13101180222 4 2.3-3.5 0-500 BLM All Rangely NE Moffat T3N R102W 1483251 1180221 2.8 1483
Area ID Thk_cat Overb Surf Fedmins 7.5' Quadrangle Cnty TR Short_tons Positive EVthk Thous_tons
T2N R100W 0 0 0 0 0 0 0 0 0 0 0 212 1247 3916 5375 5375T2N R101W 101 234 9618 3200 13154 0 0 0 0 0 0 35 105 25 166 13321T2N R102W 0 0 0 4111 4111 0 0 0 0 0 0 0 0 0 0 4111T3N R100W 0 0 0 0 0 0 0 0 0 0 0 9 926 193 1129 1129T3N R101W 577 3716 6453 8242 18990 630 2243 11427 17001 31302 151 976 1993 23414 26536 76829T3N R102W 3519 4699 13725 26606 48551 0 0 0 0 0 0 0 0 0 0 48551Grand total 4198 8649 29797 42160 84807 630 2243 11427 17001 31302 151 1234 4272 27550 33209 149319
0-500 ft of overburden 500-1000 ft of overburden0-500Total
500-1000 >1000 ft of overburdenTotal
>1000Total
TotalGrand
Coalthickness
Township
1.2-2.3 2.3-3.5 3.5-7.0 7.0-14.0 1.2-2.3 2.3-3.5 3.5-7. 7.0-14.0 1.2-2.3 2.3-3.5 3.5-7.0 7.0-14.0
Methodology for Calculating Coal Resources for the Colorado Plateau, U.S. Geological Survey National Coal Assessment C31
ConclusionsFor the assessment of 20 coal zones in fi ve formations of the Colorado
Plateau region, we established a method of taking coal-thickness data, combined with multiple layers of digital geologic and geographic data pertaining to coal distribution and coal-resource reporting parameters, to ultimately produce the most current coal resource estimates. As many as six commercially available software packages, ranging from simple conversion programs to GIS and two-dimensional surface modeling programs, were used in conjunction with three custom programs to process the digital data. Because the end-products of the assessments are in digital format such as ARC/INFO coverages, stratigraphic databases, and spreadsheet fi les, it is possible to update resource estimates as new information becomes available.
References CitedDynamic Graphics, Inc., 1997, EarthVision,. v. 4.
ESRI [Environmental Systems Research Institute, Inc.], 1998a, ARC/INFO, v.7.1.1.
ESRI [Environmental Systems Research Institute, Inc.], 1998b, ArcView, v. 3.1.
Gallegos Research Group, Inc., 1998, StratiFact, v. 4.5.
Green, G.N., 1992, The geologic digital map of Colorado in ARC/INFO format: U.S. Geological Survey Open-File Report 92-0507.
Microsoft Corporation, 1997, Microsoft Excel [part of Microsoft Offi ce 97], v. SR-1
Roberts, L.N.R., and Biewick, L.R.H., 1999, Calculation of coal resources using ARC/INFO and EarthVision: Methodology for the National Coal Resource Assessment: U.S. Geological Survey Open-File Report 99-5, 4 p.
Roberts, L.N.R., Mercier, T.J., Biewick, L.R.H., and Blake, Dorsey, 1998, A procedure for pro-ducing maps and resource tables of coals assessed during the U.S. Geological Survey’s National Coal Assessment: Fifteenth Annual International Pittsburgh Coal Conference Proceedings, CD-ROM (ISBN 1-890977-15-2), 4 p.
Wood, G.H., Jr., Kehn, T.M., Carter, M.D., and Culbertson, W.C., 1983, Coal resource clas-sifi cation system of the U.S. Geological Survey: U.S. Geological Survey Circular 891, 65 p.
National CoalResourceAssessment
Click here to return to Disc 1 Volume Table of Contents
Recommended