View
240
Download
4
Category
Preview:
Citation preview
UX Series
Confidential
Chapter 1. Disassembly & Assembly Guide1.MS-1-D.1
1-3. Disassembly & Assembly
- Main Section -
MS-1 Main Section Disassembly Except 1seg Tuner / Wireless WAN Model [MA]2
UX Series
Confidential
Battery Pack1) 2)
1.MS-1-D.2
In the state of 1), remove the Battery Pack in the direction of the arrow.Turn over the main unit, and slide the lever in the direction ofthe arrow to release the lock.
Lever
Battery Pack Battery Pack
UX Series
Confidential
Cap (Stick Pointer)1)
1.MS-1-D.3
Remove the Cap.
Remark
Shape of the Cap* There are two kinds of Cap for J Model.When replacing the Cap, be sure to use the Cap of the same shape and color as one used in the repair set.
Cap(Stick Pointer)
[MA]3
C Model
J Model [MA]3
Cap (Stick Pointer)
UX Series
Confidential
Dummy Card, Stylus1)
1.MS-1-D.3(a)
Remove the Dummy Card. Turn over the main unit and remove the Stylus.
Dummy Card
Stylus
[MA]3
2)
UX Series
Confidential
Housing (Bottom)1) 2)
1.MS-1-D.4
While disengaging the detent (two places), remove the Cover. Remove the six screws.
Remove the Housing.
3)
Screw: Blue-B6 / Green-B7 / Red-B8Cover (Bottom Screw)
Housing (Bottom)
UX Series
Confidential
Parts of the Housing (Bottom)1)
1.MS-1-D.5
Remove the two screws.
Screw: B12)
While disengaging the detent (three places), remove the Cover.
Cover (Bottom)
3) [ADD]1Screw: B1
Remove the one screw.
UX Series
Confidential
Attachment1.MS-1-D.6
Peel off the Sheet.*HDD Model - Two placesFlash Memory Model - One place
HDD Model
Sheet(Bottom)
1)
2)
Peel off the Tape.*HDD Model - Tape (one place), Kapton Tape(One place)Flash Memory Model -Tape (Two places)
HDD Model Flash Memory Model
Tape(Harness)Tape(Harness)Tape(Harness)
[ADD]4
Flash Memory Model
[ADD]4
Kapton Tape
UX Series
Confidential
Wireless LAN Card1)
1.MS-1-D.7
Screw: B4
Remove the one screw and then the Wireless LAN Card.
Wireless LAN Card
2)
Disconnect the Antenna (one place) and the terminal of the Coaxial Cable (two places) vertically.
Coaxial Cable [COR]2
Antenna(2.4/5GHz For Right)
UX Series
Confidential
HDD1)
1.MS-1-D.8
2)
Remove the five screws and the Bracket.
HDD
1. Raise the lock lever and release the lock.
2. While disconnecting the FPC, remove the HDD.
Lock Lever
FPC
Screw: B1
Bracket (HDD)
HDD Model
[MA]3
UX Series
Confidential
Parts of the HDD1)
1.MS-1-D.9
HDD
Cushion (HDD)
Remove the Cushion (two places).
HDD Model
[MA]3
UX Series
Confidential
SSD1)
1.MS-1-D.9(a)
2)
Remove the five screws.
1. Raise the lock lever to release the lock.
2. While removing the FPC, remove the SSD.
Lock Lever
Screw:B1
FPC
SSD
Flash Memory Model [MA]3
UX Series
Confidential
Parts of the SSD1)
1.MS-1-D.9(b)
Remove the two screws.
Screw:B2
Bracket(MT R)
Bracket(MT F)
SSD
Remove the SSD.
2)
Flash Memory Model [MA]3
UX Series
Confidential
Lithium Battery, Bracket (MS), Cover (WLB)1)
1.MS-1-D.10
3)
2)
Raise the lock lever to release the lock and remove the Keyboard ASSY.
Keyboard ASSY
Lock Lever
Disengage the detent (six places) and remove the Cover.
Cover (WLB)4)
Bracket (MS)
Keyboard ASSY
Sheet (Fan MS)
Disconnect the connector and remove the Lithium Battery.
* The Lithium Battery is secured with adhesive tape.
Connector
Lithium BatteryAdhesive Tape
1. Turn over the Keyboard ASSY and the Sheet (one place).
2. Disengage the detent (two places) and remove the Bracket.
UX Series
Confidential
Mother Board1)
1.MS-1-D.11
2)
Microphone
Remove the Microphone.
Mother Board
While releasing the connectors and disconnecting the FPC, remove the Mother Board.
*1: The FPC is connected to the Mother Board.
Connector
FPC *1
UX Series
Confidential
Palmrest, LCD Section1)
1.MS-1-D.12
3)
2)
4)
Cover (Screw Palmrest) Screw: B1
Peel off the Cover (two places). Remove the two screws.
Screw: B14
Remove the two screws and the Bracket.
Palmrest
LCD
While disengaging the detent (four places), remove the Palmrest.
Bracket (SWX R)
UX Series
Confidential
Update History
2006.06.08 [ADD] Procedure (Page 5) 1.101
Date Contents Version No.
[ADD]---Addition [DEL]---Deletion [CHG]---Change [COR]---Correction [MA]---Model Addition
2006.06.27 [MA] (Page 1)[COR] Description (Page 7) 1.202
2006.07.05 [MA] (Page 3, 3(a), 6, 8, 9, 9(a), 9(b)) 1.303
2006.09.04 [ADD] Procedure (Page 6) 1.404
Recommended