View
222
Download
2
Category
Preview:
Citation preview
Next Generation Central Home Heating and Hot Water Combined
Central Home Heating and Hot Water Supply
On average, hot water and home heating needs combined account for over 70%*1 of the overall energy bill in New Zealand homes.
Domestic heating is therefore an obvious area to target in reducing energy bills. This is especially pertinent during the winter months, where a combination of taking longer, hotter showers and the increased need for a warm and dry home, typically drives up power bills. An Ecodan Heat Pump System can help reduce your heating and hot water bill when compared to gas and direct electric systems.
What is Ecodan?
Ecodan is an advanced heat pump system that cleverly combines the hot water heating supply for a home with energy efficient whole home central heating; all through the same system.
Increasing energy bills, coupled with the need to heat our homes and hot water efficiently, is
driving the demand for alternative forms of domestic heating. Mitsubishi Electric has utilised their
expertise and industry-leading technology to develop Ecodan – a super energy efficient heat
pump solution that combines both hot water heating and room heating through one system.
Ecodan – Next Generation Central Heating and Hot Water Heating Combined
COP Comparison Chart
Electric Heating
Ecodan
Gas Heating (Non-Condensing)
0.82 0.99 3.20
Return on Investment
The estimated return on investment of an Ecodan System, when compared to a gas or direct electric heating system, is about 10 years*4. There are ways of reducing this payback period further, such as taking advantage of lower cost nightly electricity tariffs available; reducing homeowners’ energy bills by heating the hot water cylinder during the night. Large households with high hot water usage could bring the payback period down significantly, closer to 5 years*4.
• Savings could be as much as 35% when compared to traditional gas central heating systems.
• Savings could be as much as 40% when compared to traditional direct electric heaters.
*1 Based on data sourced from NZGBC.
*2 The overall system efficiency and energy savings will depend on the comparison with your current heating system, satisfactory system design and installation, and operational settings i.e. how you use the heating system.
*3 Based on manufacturer information for gas instant hot water heater (non-condensing).
*4 Payback period comparison based on average energy supplier costs per kWh over an average winter heating period. Actual savings may vary in line with gas and electricity price fluctuations and seasonal conditions. This is an estimate only.
Heat pumps use electrical energy and take low grade heat energy from the outdoor air, to heat refrigerant which in turn heats water for domestic use and space heating. The efficiency of a heat pump is known as the Coefficient of Performance or COP. This is a ratio of the heat delivered to power consumed. For every 1kW of electrical input energy, Ecodan absorbs renewable heat energy from the outdoor air to provide the home with an average of at least 3.2kW*2 of heat output. Compared to typical gas and direct electric heating systems that can
have higher running costs with COPs as low as 0.82*3, Ecodan provides an energy efficient alternative.
2.2kWLow temperature renewable heat energy taken from the environment
Electrical energy input
1kW
3.2kWHeat energy output
As independently tested by BSRIA based upon BSEN14511 Part 3 standard rating conditions. Due to the method of operation, the performance of heat pumps will vary based upon the temperature of the heat source and the requirements of the heat delivered. The BSEN14511 testing relates to the heat pump performance only and not the entire heating system.
2
Fast Heat Up Times!
• Fast water heating times from 15°C – 55°C in 1 hour for a 3 bedroom house*1
• Less than 30 minutes to re-heat half the tank (100 litres)*1
• Even faster heat up times with Zubadan Technology*2
*1 When using PUHZ-W112VHA, ambient temperature above 2°C.*2 Zubadan only available on specific models – see specification tables.
Ecodan is a highly energy efficient hot water heat pump system comprised of an outdoor hot
water heat pump and an indoor component – a Hydrobox or a Cylinder Tank. A reliable total
home heating solution using radiators and/or underfloor heating in conjunction with hot water
supply provides year-round comfort with advanced control.
Ecodan Central Heating with Domestic Hot Water Systems
With proven Mitsubishi Electric technology, Ecodan is designed for New Zealand conditions; maintaining high performance during the winter months when heating is in high demand.
Whether you need central whole home heating, hot water or both, Ecodan Hydrobox and Cylinder Systems can provide the perfect solution.
Both the Hydrobox and Cylinder are compatible with the Monobloc and Split Type Ecodan Outdoor Units ranging from 4.5–14 kW of heating and hot water for your home or light commercial application.
Packaged Cylinder System
The 200 litre Cylinder provides improved performance and fast heat up times through the use of Plate Heat Exchanger Technology and FTC5 Control. The Cylinders are completely pre-plumbed and wired for ease of installation. The Cylinder can provide heating and hot water to your home.
Packaged Hydrobox System
The Hydrobox is primarily used for space heating in the form of underfloor and/or radiators. With a small footprint that is sized similarly to Combi Boilers, the Hydrobox provides a highly adaptable solution for retrofit and new builds. Whether connecting the Monobloc or Split Unit only, 2 pipes are connected to supply the unit just like the Cylinder. For systems where a third party tank is to be installed, a 3-way valve can be added to the system and connected to the FTC5 Controller.
Outdoor Monobloc/Split
PUHZ Indoor Cylinder
UFH*
Radiator
Hot Water
UFH*
Radiator
Hot WaterIndoor 3rd Party Cylinder
3-Way Valve
Indoor Hydrobox
Outdoor Monobloc/Split
PUHZ
Packaged Cylinder System
Packaged Hydrobox System
*UFH: Under Floor Heating
4
Ecodan Hot Water Heat Pumps provide highly efficient hot water to pools and spas.
Comprising of a durable outdoor hot water heat pump, specialised heat exchanger, flow switch
and advanced controller, Ecodan is the ideal and cost efficient way to heat your pool or spa all
year round.
Ecodan for Pool and Spa Applications
Spa Pools
Spa pools consume more power than many swimming pools due to higher temperatures and potential heat losses. Installing a hot water heat pump to an existing spa pool can significantly reduce your heating costs. Power consumption can be reduced by 3 to 4 times.
Swimming Pools
Most swimming pools are used during the summer months and remain unused for the rest of the year. Installing a hot water heat pump can enable you to enjoy your swimming pool year-round!
A range of titanium coil / PVC shell heat exchangers are matched to the PUHZ hot water heat pump units. This removes any risk of corrosion-related damage due to salt or chlorine water treatment and simplifies pool water pipe work.
Packaged Heat Exchanger System
Outdoor Split PUHZ
Heat Exchanger Pool / Spa
Ecodan Technology, Smart Energy Monitoring and System Management
State of the art energy monitoring and management of the Ecodan Heat Pump System means
families now have the visibility and freedom to efficiently manage their overall household power
consumption for heating and hot water. Energy monitoring ensures households can take
advantage of off-peak tariffs, providing them the ability to save even more on their power bill.
Smart Energy Monitoring
View electricity consumption and heat output on the remote controller. End-users can now easily check the energy data of the Ecodan Heat Pump.
Data Shown on the Remote Controller:
• Consumed electrical energy for space heating, cooling and domestic hot water (kWh)
• Delivered energy for space heating, cooling and domestic hot water (kWh)
Other Features
• Daily, monthly and yearly data are stored and can be displayed using the main remote controller
• External power meter and heat meter can be connected for accurate measurement
• An SD card is included for storing usage data
Heating capacity produced
Electric energy used
2-Zone Control allows you to simultaneously control two different temperature zones.
Using Ecodan, it is possible to control two different flow temp-eratures, thereby managing two different heating load requirements.
The system can adjust and maintain two flow temperatures when different temperatures are required for different rooms; for example, controlling a flow temperature of 45°C for the bedroom radiators and another flow temperature of 35°C for the living room underfloor heating.
• Easy installation: G1 screw type flexi piping connections.
• Compact: fits on top of Cylinder or wall mountable with Hydrobox.
• All in one kit: Key functional components are incorporated.
Optional PAC-TZ01-E 2-Zone Kit
* Items such as a Mixing Tank, Mixing Valve, Flow Switch and Pumps are not included and need to be purchased locally.
Or use the optional PAC-TZ01-E 2-Zone Kit.
FTC
40°C
30°C
Hydro Box
Mixing Tank/Header
Mixing Control
Wireless Remote Controller as Thermistor
Flow Switch Radiator
Underfloor Heating
Flow Switch
Mixing Valve
Pump
Pump
2 Zone Control System*
6
Plate Heat Exchanger and Patented Scale Trap Technology*
The Aluminium Plate Heat Exchanger and patented Scale Trap Technology help achieve greater efficiencies. In conventional systems, there is a risk of calcium scale building up on the Plate Heat Exchanger if it is exposed to tap water directly; therefore making it difficult to heat tap water. To resolve this problem, Ecodan is equipped with a “Scale Trap” that catches calcium nuclei in the tap water before it has a chance to grow into large scales, thereby inhibiting build-up in the External Heat Exchanger.
Ecodan can use a Plate Heat Exchanger to heat tap water, resulting in much higher domestic hot water performance.
In the case of special localised conditions such as very hard tap water, please consult a specialist before installation.
The Secret Behind Our External Plate Heat Exchanger System
Circulating Water
Tap Water
Hot Water
Fresh Water
Pump
Scale Trap
P - HEX
External P-HEX CircuitDHW Storage Tanks
* Only available on Mitsubishi Electric made cylinders.
By estimating future changes in room temperature, the system works to prevent unnecessary increases and decreases in the flow temperature. Auto Adaptation maximises both comfort and energy savings.
1°C 2%
0
-5
-10
-15
0:00
1:00
2:00
3:00
4:00
5:00
6:00
7:00
8:00
40
35
30
25
0:00
1:00
2:00
3:00
4:00
5:00
6:00
7:00
8:00
19
20
21
22
23
0:00
1:00
2:00
3:00
4:00
5:00
6:00
7:00
8:00
a) Outdoor temperature is gradually decreasing…
[Example]
b) Target flow temperature
c) Room temperature
By Auto Adaptation, flow temperature can be lowered even when outdoor temp. is decreasing.
By Auto Adaptation, flow temperature can be lowered without sacrificing comfort.
Actual outdoor temperature
with Heat Curve estimation
with Auto Adaptation
Target room temperature
Target flow temp. goes up following the heat curve.
-6°C
-10°C
36.6°C
30.0°Cat A-10
34.6°Cat A-6
Actual with Auto Adaptation
Room temp. can be kept stable and stays at the targeted level at the end.
Repeats Thermo ON/OFF and room temp. becomes unstable.
Target flow temp. is gradually lowered.
Room Temperature
Modify the flow temperature by comparing actual and estimated room temperature
Target Temperature
3 points FutureCurrentT0 T1 Time
Higher than Target Temperature
Approximately same as Target Temperature
Lower than Target Temperature
Lower the flow temperature
Keep the flow temperature
Raise the flow temperature
Auto Adaptation
Our advanced Auto Adaptation Function measures the room temperature and outdoor temperature, calculating the required heating capacity for the room. The flow temperature is automatically controlled according to the required heating capacity, while optimal room temperature is maintained at all times; ensuring the appropriate heating capacity and preventing energy wastage.
Future Room Temperature Estimation
Zubadan – Reliable Performance in Low Temperature Outdoor Conditions
New Generation Zubadan* provides powerful heating in cold regions where most heat
pumps’ performance lacks. Zubadan’s rated heating capacity is maintained even in outdoor
temperatures as low as –15°C, guaranteeing total home comfort when you need it most.
Benefits of Zubadan New Generation
Approximately 22% Higher than our previous model
ZUBADAN New Generation
Previous model
Nominal capacity can be kept at -15°C !
Outdoor-Air Temperature at Intake Duct-28°C
1514131211109
-20°C -15°C -7°C 0°C
Example: PUHZ-SHW140YHA W45 (according to EN 14511)
Inte
gra
ted
Cap
acity
(kW
)
* Zubadan only available on specific models – see specification tables pg 9 and 11.
Zubadan Inverter Technology
New Generation Zubadan Inverter Technology* provides powerful heating in cold regions where heat pump performance can diminish. With Zubadan, rated heating capacity is maintained even in outdoor temperatures as low as -15°C, with guaranteed heating operation at -25°C. Zubadan guarantees a warm, comfortable home when you need it most. Furthermore, Zubadan can provide even faster tank heat up times in low ambient temperatures compared to standard models.
Flash Injection Circuit
Heat Interchanger (HIC)
Injection Compressor
Flash Injection Technology
The Flash Injection Circuit is an original Mitsubishi Electric technology. A heat exchange process at the Heat Interchanger transforms liquid refrigerant into a two-phase, gas-liquid state and then compresses the gas-liquid refrigerant at the Injection Compressor. This circuit secures a sufficient flow rate of refrigerant for heating when outdoor temperatures are very low.
Thanks to an improved Heat Interchanger and the introduction of a new Injection Compressor, the Flash Injection Circuit is now more powerful then ever.
8
Key Features
• Self-contained unit, only requiring water and electric connections
• No need for gas supply, flues or ventilation
• Single phase power supply with a low starting current
• Low maintenance and quiet operation
• Operates with outside temperatures as low as -25ºC with Zubadan – HW Models
• 5ºC – 60ºC outlet water temperature
• Optional 2-Zone Energy Efficient Space Heating Control
• Energy monitoring as standard
Domestic Applications
• Heating and hot water
• The vast majority of NZ homes
Commercial Applications
• Small retail outlets
• Dental and doctors’ surgeries
• Public sector and commercial buildings
Technical Specifications Ecodan Monobloc Air Source Heat PumpsPUHZ-(H)W OUTDOOR UNITS
Our range of Ecodan Monobloc Air Source Heat Pumps are available in 5, 8.5, 11.2 and 14kW capacities. Designed to suit a wide range of applications, these models offer a viable solution for the varying requirements that domestic and small commercial applications demand.
ZUBADAN
OUTDOOR UNIT PUHZ-W50VHA2(-BS) PUHZ-W85VHA2(-BS) PUHZ-W112VHA(-BS) PUHZ-HW140VHA2(-BS)
HEATING*1
(A7/W35)
Capacity (kW) 5.00 9.00 11.20 14.00
Power Input (kW) 1.11 2.15 2.51 3.29
COP 4.50 4.18 4.47 4.26
HEATING*2
(A2/W35)
Capacity (kW) 5.00 8.50 11.20 14.00
Power Input (kW) 1.43 2.68 3.35 4.50
COP 3.50 3.17 3.34 3.11
OPERATING AMBIENT TEMPERATURE (°C DB)*4 -15 ~ +35°C -20 ~ +35°C -20 ~ +35°C -25 ~ +35°C
SOUND PRESSURE LEVEL AT 1M (dBA)*1 46 48 53 53
LOW NOISE MODE (dBA)*1 40 42 46 46
WATER DATA
Water Pipe Size1" BSP Parallel Thread
*ISO 228/1-G1B)1" BSP Parallel Thread
*ISO 228/1-G1B1" BSP Parallel Thread
*ISO 228/1-G1B1" BSP Parallel Thread
*ISO 228/1-G1B
Flow Rate (l/min) 14.3 25.8 32.1 40.1
Water Pressure Drop (kPa) 12 13.5 6.3 9
DIMENSIONS (mm)
Width 950 950 1020 1020
Depth 330+30*3 330+30*3 330+30*3 330+30*3
Height 740 943 1350 1350
WEIGHT (kg) 64 79 133 134
ELECTRICAL DATA
Electrical Supply 220-240V, 50Hz 220-240V, 50Hz 220-240V, 50Hz 220-240V, 50Hz
Phase Single Single Single Single
Maximum Current (A) 13 23 29.5 35
Fuse Rating 16 25 32 40
*1 Under normal heating conditions at outdoor temp: 7°CDB / 6°CWB, outlet water temp 35°C, inlet water temp 30°C as tested to BS EN14511.*2 Under normal heating conditions at outdoor temp: 2°CDB / 1°CWB, outlet water temp 35°C, inlet water temp 30°C.*3 Grille.*4 Heating maximum ambient temperature ~21°CDB, DHW hot water maximum ambient temperature ~35°CDB.
PUHZ-W50VHA2(-BS) PUHZ-W85VHA2(-BS) PUHZ-W112VHA(-BS) PUHZ-HW140VHA2(-BS)
9
Key Features
• Split unit allowing water connections to be made internally
• No need for gas supply, flues or ventilation
• Single phase power supply with a low starting current
• Low maintenance and quiet operation
• Operates in outside temperatures as low as -28ºC with Zubadan Technology – HW Models
• 2-Zone Energy Efficient Space Heating Control
• Energy monitoring as standard
Domestic Applications
• Heating and hot water
• The vast majority of NZ homes
Commercial Applications
• Small retail outlets
• Dental and doctors’ surgeries
• Public sector and commercial buildings
Ecodan Split Air Source Heat PumpsPUHZ-S(H)W OUTDOOR UNITS
The Ecodan Split Air Source Heat Pump ranges from 4.5kW to 16kW. Designed to suit a wide range of applications, these models offer a viable solution for the varying requirements that domestic and small commercial applications demand.
PUHZ-SW75VHA(-BS)PUHZ-SW50VKA(-BS)SUHZ-SW45VAH
ZUBADAN ZUBADAN
OUTDOOR UNIT SUHZ-SW45VAH PUHZ-SW50VKA(-BS) PUHZ-SW75VHA(-BS) PUHZ-SW120VHA(-BS) PUHZ-SHW80VHA(-BS) PUHZ-SHW112VHA(-BS)
HEATING*1
(A7/W35)
Capacity (kW) 4.50 5.50 8.00 16.00 8.00 11.20
Power Input (kW) 0.89 1.24 1.82 3.90 1.72 2.51
COP 5.06 4.42 4.40 4.10 4.65 4.46
HEATING*2
(A2/W35)
Capacity (kW) 3.50 5.00 7.50 12.00 8.00 11.20
Power Input (kW) 1.15 1.68 2.21 3.70 2.25 3.35
COP 3.04 2.97 3.40 3.24 3.55 3.34
OPERATING AMBIENT TEMPERATURE (°C DB)*4 -15 ~ +35°C -15 ~ +35°C -20 ~ +35°C -20 ~ +35°C -28 ~ +35°C -28 ~ +35°C
SOUND PRESSURE LEVEL AT 1M (dBA)*1 - 46 51 54 51 52
LOW NOISE MODE (dBA)*1 42 42 48 51 49 50
WATER DATA Flow Rate (l/min) 12.9 15.8 22.9 45.9 20.4 32.1
DIMENSIONS (mm)
Width 840 809+62*5 950 950 950 950
Depth 330 300 330+30*3 330+30*3 330+30*3 330+30*3
Height 880 630 943 1350 1350 1350
WEIGHT (kg) 54 43 75 118 120 120
ELECTRICAL DATA Type R410A R410A R410A R410A R410A R410A
Charge (kg) - 10m Pipe Length 1.4 1.4 3.2 4.6 5.5 5.5
Pipe Size - Gas/Liquid (mm (in)) 12.7 (1/2") / 6.35 (1/4") 12.7 (1/2") / 6.35 (1/4") 15.88 (5/8") / 9.52 (3/8") 15.88 (5/8") / 9.52 (3/8") 15.88 (5/8") / 9.52 (3/8") 15.88 (5/8") / 9.52 (3/8")
Connection Type Flared Flared Flared Flared Flared Flared
Max Pipe Length (m) 30 40 40 75 75 75
Min Pipe Length (m) 2 2 2 2 2 2
Max Height Difference (m) 30 30 30 30 30 30
ELECTRICAL DATA Electrical Supply 220-240V, 50Hz 220-240V, 50Hz 220-240V, 50Hz 220-240V, 50Hz 220-240V, 50Hz 220-240V, 50Hz
Phase Single Single Single Single Single Single
Maximum Current (A) 12 13 17 29.5 29.5 35
Fuse Rating 20 16 25 40 32 40
*1 Under normal heating conditions at outdoor temp: 7°CDB / 6°CWB, outlet water temp 35°C, inlet water temp 30°C as tested to BS EN14511.
*2 Under normal heating conditions at outdoor temp: 2°CDB / 1°CWB, outlet water temp 35°C, inlet water temp 30°C.*3 Grille.
*4 Heating maximum ambient temperature ~21°CDB, DHW hot water maximum ambient temperature ~35°CDB.
*5 Electrical cover.
10
PUHZ-SHW80/112VHA(-BS)PUHZ-SW120VHA(-BS)
ZUBADAN ZUBADAN
OUTDOOR UNIT SUHZ-SW45VAH PUHZ-SW50VKA(-BS) PUHZ-SW75VHA(-BS) PUHZ-SW120VHA(-BS) PUHZ-SHW80VHA(-BS) PUHZ-SHW112VHA(-BS)
HEATING*1
(A7/W35)
Capacity (kW) 4.50 5.50 8.00 16.00 8.00 11.20
Power Input (kW) 0.89 1.24 1.82 3.90 1.72 2.51
COP 5.06 4.42 4.40 4.10 4.65 4.46
HEATING*2
(A2/W35)
Capacity (kW) 3.50 5.00 7.50 12.00 8.00 11.20
Power Input (kW) 1.15 1.68 2.21 3.70 2.25 3.35
COP 3.04 2.97 3.40 3.24 3.55 3.34
OPERATING AMBIENT TEMPERATURE (°C DB)*4 -15 ~ +35°C -15 ~ +35°C -20 ~ +35°C -20 ~ +35°C -28 ~ +35°C -28 ~ +35°C
SOUND PRESSURE LEVEL AT 1M (dBA)*1 - 46 51 54 51 52
LOW NOISE MODE (dBA)*1 42 42 48 51 49 50
WATER DATA Flow Rate (l/min) 12.9 15.8 22.9 45.9 20.4 32.1
DIMENSIONS (mm)
Width 840 809+62*5 950 950 950 950
Depth 330 300 330+30*3 330+30*3 330+30*3 330+30*3
Height 880 630 943 1350 1350 1350
WEIGHT (kg) 54 43 75 118 120 120
ELECTRICAL DATA Type R410A R410A R410A R410A R410A R410A
Charge (kg) - 10m Pipe Length 1.4 1.4 3.2 4.6 5.5 5.5
Pipe Size - Gas/Liquid (mm (in)) 12.7 (1/2") / 6.35 (1/4") 12.7 (1/2") / 6.35 (1/4") 15.88 (5/8") / 9.52 (3/8") 15.88 (5/8") / 9.52 (3/8") 15.88 (5/8") / 9.52 (3/8") 15.88 (5/8") / 9.52 (3/8")
Connection Type Flared Flared Flared Flared Flared Flared
Max Pipe Length (m) 30 40 40 75 75 75
Min Pipe Length (m) 2 2 2 2 2 2
Max Height Difference (m) 30 30 30 30 30 30
ELECTRICAL DATA Electrical Supply 220-240V, 50Hz 220-240V, 50Hz 220-240V, 50Hz 220-240V, 50Hz 220-240V, 50Hz 220-240V, 50Hz
Phase Single Single Single Single Single Single
Maximum Current (A) 12 13 17 29.5 29.5 35
Fuse Rating 20 16 25 40 32 40
*1 Under normal heating conditions at outdoor temp: 7°CDB / 6°CWB, outlet water temp 35°C, inlet water temp 30°C as tested to BS EN14511.
*2 Under normal heating conditions at outdoor temp: 2°CDB / 1°CWB, outlet water temp 35°C, inlet water temp 30°C.*3 Grille.
*4 Heating maximum ambient temperature ~21°CDB, DHW hot water maximum ambient temperature ~35°CDB.
*5 Electrical cover.
Flow Temperature ControllerFTC2B FLOW TEMPERATURE CONTROLLER
The FTC2B has been developed to allow the Ecodan PUHZ Range to interface with third party or BEMS (Building Energy Management System) Controls. A combination of volt free and voltage inputs allow the Ecodan PUHZ Range to be used in applications where only simple on/off and temperature control is required.
Functions that can be controlled by third party controls:
• On/Off Heating Mode
• On/Off Heating ECO Mode
• On/Off Hot Water Mode
• On/Off Holiday Mode
• On/Off Legionella Mode
• Change Water Flow Temperature
Functions that can be monitored by third party controls:
• Unit Running
• Error
• Defrost
The ability to interface with third party controls opens up a huge number of application opportunities. Many processes simply require a heat source that provides hot water, without polished end-user controls. The FTC2B Controller allows the Ecodan PUHZ to be used in these applications. FTC2B inputs and outputs can be used in conjunction with local BEMS.
Application Examples
• Smart home integration
• Leisure centres
• Agriculture
• Industrial process heating
• Under soil heating
PAC-IF032B-E
FTC2B PAC-IF032B-E
DIMENSIONS (mm) Width 336
Depth 69
Height 278
WEIGHT (KG) 2.4
Operating Ambient Temperature (°C DB) 0~+35ºC (RH<80%)
ELECTRICAL DATA Electrical Supply Powered from Outdoor Unit (240v)
Phase Single
11
EHST/ERST/EHPT Cylinder
Key Features
• Simple graphical control
• Optional 2-Zone Energy Efficient Space Heating Control
• Scale Trap Technology
• Sleek modern design
• Pre-plumbed and wired for faster installation
• SD card commissioning
• Energy monitoring as standard
• Compatible with home automation via Modbus
• BMS compatible
FTC5 Packaged Cylinder for Ecodan Monobloc and Split UnitsFTC5 PACKAGED CYLINDER
The Packaged Cylinder offers a highly adaptable heating solution for retrofit or new builds. Designed specifically by Mitsubishi Electric to integrate with the Ecodan Monobloc and Split Air Source Heat Pump Range, the Cylinder provides improved performance and faster heat up times through the use of Plate Heat Exchanger Technology. Fast commissioning via an SD card and energy monitoring functions are included.
CYLINDER EHST20D(C)-VM2CR2 ERST20D(C)-VM2CR2 EHPT20X-VM2C
CYLINDER TYPE Packaged Split Packaged Split Reversible Packaged Monobloc
NOMINAL HOT WATER VOLUME (LITRES) 200 200 200
OPERATING AMBIENT TEMPERATURE (°C DB) 0 ~ +35°C (RH<80%) 0 ~ +35°C (RH<80%) 0 ~ +35°C (RH<80%)
SOUND PRESSURE LEVEL AT 1M (dBA) 28 28 28
WATER DATA
Max Flow Rate (l/min) 27.7 27.7 27.7
Primary Pump Grundfos UPM2 15 70 - 130 Grundfos UPM2 15 70 - 130 Grundfos UPM2 15 70 - 130
Sanitary Hot Water Pump Grundfos UPSO 15-60 130 CIL2 Grundfos UPSO 15-60 130 CIL2 Grundfos UPSO 15-60 130 CIL2
Connection Size (mm) Heating / DHW 28 / 22 28 / 22 28 / 22
Primary Expansion Vessel (Litres) 12 12 12
Charge Pressure (MPa (Bar)) 0.1 (1) 0.1 (1) 0.1 (1)
WATER SAFETYDEVICES
Water Circuit
Control Thermistor (°C) 1 - 80 1 - 80 1 - 80
Pressure Relief Valve (MPa (Bar)) 0.3 (3) 0.3 (3) 0.3 (3)
Flow Sensor (Minimum Flow 5L/min) Supplied Supplied Supplied
DHW CylinderControl Thermistor (°C) 40-70 40-70 40-70
Temp and Pressure Relief Valve (°C)/ (MPa (Bar)) 90 / 0.7 (7) 90 / 0.7 (7) 90 / 0.7 (7)
DIMENSIONS (mm)
Width 595 595 595
Depth 680 680 680
Height 1600 1600 1600
WEIGHT EMPTY / FULL (kg) 110 / 320 110 / 320 115 / 307
ELECTRICAL DATA
Control Board (Optionally Powered by Outdoor Unit)
Electrical Supply 220-240V, 50Hz 220-240V, 50Hz 220-240V, 50Hz
Phase Single Single Single
Breaker (A) 10 10 10
Booster Heater
Electrical Supply 220-240V, 50Hz 220-240V, 50Hz 220-240V, 50Hz
Phase Single Single Single
Capacity (kW) 2 2 2
Max Running Current (A) 9 9 9
Breaker (A) 16 16 16
MECHANICAL ZONES DHW and 1 Heating Zone*1 DHW and 1 Heating Zone*1 DHW and 1 Heating Zone*1
Cylinder includes: Flow Temperature Controller (FTC5) with Main Controller and Temperature Sensors, Pumps & Valves for Zone 1 and DHW use, Flow Sensor, Plate Heat Exchanger, Scale Trap, 2kW Booster Heater and Expansion Vessel. *1 Optional 2-Zone Accessory Pack available.
MelcoBEMS Mini (Modbus)
12
Key Features
• Simple graphical control
• 2-Zone Energy Efficient Space Heating Control
• Sleek modern design
• Pre-plumbed and wired for faster installation
• SD card commissioning
• Energy monitoring as standard
• Compatible with home automation via Modbus
• BMS compatible
FTC5 Packaged Hydrobox for Ecodan Monobloc and Split UnitsFTC5 PACKAGED HYDROBOX
The Hydrobox is primarily used for space heating in the form of underfloor and/or radiators. A small footprint and a similar size to Combi Boilers, they are a highly adaptable solution for retrofit and new builds. Whether connecting the packaged or split unit, only two pipes are connected to supply the unit just like the Cylinder. Hydraulic components are included with FTC5 Control, whilst the split type model features the Heat Exchanger built into the Hydrobox. SD card comissioning and energy monitoring are included. For systems where a third party tank is to be installed, a 3-way valve can be added to the system and connected to the FTC5 Controller.
EHSD/ERSD/EHPX Hydrobox
HYDROBOX EHSD(C)-VM2CR2 ERSD(C)-VM2CR2 EHPX-VM2C
CYLINDER TYPE Packaged Split Packaged Split Reversible Packaged Monobloc
OPERATING AMBIENT TEMPERATURE (°C DB) 0 ~ +35°C (RH<80%) 0 ~ +35°C (RH<80%) 0 ~ +35°C (RH<80%)
SOUND PRESSURE LEVEL AT 1M (dBA) 28 28 28
WATER DATA
Max Flow Rate (l/min) 27.7 27.7 27.7
Pump Grundfos UPM2 15 70 - 130 Grundfos UPM2 15 70 - 130 Grundfos UPM2 15 70 - 130
Connection Size (mm) 28 G1 Nut 28
Primary Expansion Vessel (Litres) 10 10 10
Charge Pressure (MPa (Bar)) 0.1 (1) 0.1 (1) 0.1 (1)
WATER SAFETYDEVICES
Water Circuit
Control Thermistor (°C) 1 - 80 1 - 80 1 - 80
Pressure Relief Valve (MPa (Bar)) 0.3 (3) 0.3 (3) 0.3 (3)
Flow Sensor (Minimum Flow 5L/min) Supplied Supplied Supplied
DHW Cylinder
Booster Heater Control Thermistor (°C) 80 80 80
Booster Heater Manual Reset Thermostat (°C) 90 90 90
Booster Heater Thermal Cut Off (°C) 121 121 121
DIMENSIONS (mm)
Width 530 530 530
Depth 360 360 360
Height 800 800 800
WEIGHT EMPTY / FULL (kg) 44 / 50 45 / 51 37 / 42
ELECTRICAL DATA
Control Board (Optionally Powered by Outdoor Unit)
Electrical Supply 220-240V, 50Hz 220-240V, 50Hz 220-240V, 50Hz
Phase Single Single Single
Breaker (A) 10 10 10
Booster Heater(Optionally Powered if Required)
Electrical Supply 220-240V, 50Hz 220-240V, 50Hz 220-240V, 50Hz
Phase Single Single Single
Capacity (kW) 2 2 2
Max Running Current (A) 9 9 9
Breaker (A) 16 16 16
Hydrobox includes: Flow Temperature Controller (FTC5) with Main Controller and Temperature Sensors, Water Circulation Pump, Flow Sensor, 2kW Booster Heater and Expansion Vessel.
MelcoBEMS Mini (Modbus)
13
Key Features
• Simple graphical control
• 2-Zone Energy Efficient Space Heating Control and Hot Water
• Sleek modern design
• SD card commissioning
• Energy monitoring as standard
• Compatible with home automation via Modbus
• BMS compatible
Third Party Cylinder via Hydrobox for Ecodan Monobloc and Split UnitsFTC5 PACKAGED HYDROBOX AND CYLINDER
We offer a range of New Zealand made hot water cylinders manufactured to the highest standards, complete with heat exchanger coil designed specifically for Mitsubishi Electric hot water heat pump Hydrobox systems. Cylinders are supplied as standard with all water connections on the front and include standard electric element, thermostat and TPR valve. Sensor pockets are correctly positioned for the cylinder temperature sensor. There are sizes for mains pressure cylinders or buffer tanks and these can be made from 150 to 800 litres. Custom designs are also available.
FTC5 CONTROLLER – WITH ENERGY MONITORING
Mitsubishi Electric’s Fifth Generation Controller (FTC5) includes intelligent room temperature control as standard. This, together with advanced weather compensation, ensures the system delivers efficient, comfortable heating regardless of the season. FTC5 now also includes energy monitoring, showing consumed and produced energy.
EHSD/ERSD/EHPX Hydrobox
14
ZUBADAN ZUBADAN
OUTDOOR UNIT* PUHZ-SW50VKA(-BS) PUHZ-SW75VHA(-BS) PUHZ-SW120VHA(-BS) PUHZ-SHW80VHA(-BS) PUHZ-SHW112VHA(-BS)
HEATING*1
(A7/W35)
Capacity (kW) 5.50 8.00 16.00 8.00 11.20
Power Input (kW) 1.24 1.82 3.90 1.72 2.51
COP 4.42 4.40 4.10 4.65 4.46
HEATING*2
(A2/W35)
Capacity (kW) 5.00 7.50 12.00 8.00 11.20
Power Input (kW) 1.68 2.21 3.70 2.25 3.35
COP 2.97 3.40 3.24 3.55 3.34
FLOW SWITCH FSW85 FSW85 FSW140 FSW85 FSW125
HEAT EXCHANGER Vaportec HXTi Vaportec HXTi Vaportec HXTi Vaportec HXTi Vaportec HXTi
Ancillary equipment such as water pumps and expansion tanks are to be provided separately by the installer, and selected to meet the individual system pressure and flow requirements. This system is supplied with the Vaportec HXTi Heat Exchanger.
* For full outdoor specifcations see pages 10 to 11.*1 Under normal heating conditions at outdoor temp: 7°CDB / 6°CWB, outlet water temp 35°C, inlet water temp 30°C as tested to BS EN14511.*2 Under normal heating conditions at outdoor temp: 2°CDB / 1°CWB, outlet water temp 35°C, inlet water temp 30°C.
VAPORTEC HEAT EXCHANGER HXTi 8
WATER PIPE SIZE (mm) 50mm PVC (max. pressure 4 bar)
LIQUID / GAS PIPE SIZE (inch) 3/8" and 5/8"
DIMENSIONS (mm)
Width 165
Depth 235
Height 640
WEIGHT (kg) 4.4
Key Features
• Reliable, year-round water heating
• Inverter driven for maximum energy efficiency
• Operation in outdoor temperatures as low as -25°C
• Easy to use LCD Wall Controller with 7 Day Timer
• FTC2 intelligent controller for efficient temperature control
Ecodan Split Units for Pool and Spa ApplicationsPUHZ-S(H)W OUTDOOR UNITS
These split systems are ideal for pool & spa applications and require an external heat exchanger. The flexibility of this system allows the installer to position the heat exchanger right where the hot water is required for both new and retrofit installations. Vaportec HXTi with high density plastics and a titanium coil heat exchanger for swimming and spa pool heating will require mounting and installation of refrigerant pipe work to the PUHZ-SW outdoor unit. The system is controlled by the PAR-W21, 7 day timer/controller and an advanced PAC-IF031 (FTC2) interface.
Vaportec HXTi Heat Exchanger
PAR-W21 Controller
PUHZ-SW75VHA(-BS) PUHZ-SW120VHA(-BS)PUHZ-SW50VKA(-BS) PUHZ-SHW80/112VHA(-BS)
15
Be sure to ask for Mitsubishi Electric. Other brands share the 3-diamond logo, however they are separate to the Mitsubishi Electric brand and cannot supply the models, features or guarantees outlined in this brochure. All models, features and specifications are subject to change and amendment at anytime. Printed March 2018.
Mitsubishi Electric’s manufacturing facility in Livingston, Scotland produces Ecodan Air Source Heat Pumps, Controls and Cylinders for the UK and European markets. The production facility, custom-built by the company in 1994, currently employs 420 staff and includes specially adapted and scalable production lines for Ecodan Air Source Heat Pumps, a new Cylinder and a purpose-built Ecodan testing facility.
Mitsubishi Electric’s manufacturing plants are all ISO14001 and ISO9001 registered, an international benchmark ensuring we meet and continually improve upon quality and environmental standards.
Ecodan Full 5 Year WarrantyEvery Ecodan Air Source Heat Pump comes with a full 5 year warranty as standard, subject to the following conditions:
• The Ecodan purchase and installation is registered with BDT.
• The Ecodan must be installed and commissioned by an accredited BDT Installer.
Ecodan – Manufactured in the United Kingdom
HOME AUTOMATION AND COMMERCIAL
• Ecodan Systems are compatible with a range of home automation systems via modbus using the MelcoBEMS Mini Modbus Interface.
• As part of a wider range of applications, commercial Ecodan products are also available. Please contact your local BDT Representative or branch nearest you for more details.
Black Diamond TechnologiesExclusive distributor of Mitsubishi Electric products in New Zealand.
WELLINGTONHEAD OFFICE
1 Parliament StreetPO Box 30772 Lower Hutt 5040
Phone (04) 560 9147 Fax (04) 560 9133
AUCKLANDBRANCH
Unit 1, 4 Walls RoadPO Box 12726Penrose, Auckland 1642
Phone (09) 526 9347Fax (09) 526 9369
CHRISTCHURCHBRANCH
44 Halwyn DrivePO Box 16904Hornby, Christchurch 8441
Phone (03) 341 2837Fax (03) 341 2838
www.mitsubishi-electric.co.nz
For more information on Ecodan Central Heating and Hot Water, please call our Customer Service Team on 0800 784 382
Recommended