View
128
Download
29
Category
Preview:
Citation preview
CBD/G
2.53.03.5
Service Manual
Cargo Range
CARGO 2.5
< Tillbaka till Index
SERVICE MANUALpage 3
INTERNALCOMBUSTION
2,5 - 3,0 - 3,5 t
BOLOGNA’S FACTORY, AFTER SALES SERVICE
CESAB S.p.a. reserves all rights ofreproduction of this handbook
The text and the numbering systemmay not be used in other printed matter,reprinted or translated, whether entirelyor in part, without written authorizationfrom
CESAB reserves the right to make anynecessary modifications without obligationto promptly update this handbook.
Copyright byCESAB S. p. A.
SERVICE MANUALpage 4
2,5 - 3,0 - 3,5 tINTERNAL
COMBUSTION
INDEX
TECHNICAL DATA ............................................................................................. p. 6
OPERATOR’S SEAT .......................................................................................... p. 8Pedals version ................................................................................................... p. 8Service brake .................................................................................................... p. 8
DASHBOARD ..................................................................................................... p. 9Dashboard indicator .......................................................................................... p. 9Parking switch ................................................................................................... p. 11Truck start up ..................................................................................................... p. 11Set of levers - Load handling.............................................................................. p. 12Capacity plates ................................................................................................. p. 12
ENDOTHERMIC ENGINE .................................................................................. p. 13KUBOTA ENGINE ............................................................................................. p. 13Kubota engine data ........................................................................................... p. 14Continental engine data ..................................................................................... p. 15Oil change and engine oil filter replacement ....................................................... p. 16Topping up with coolant...................................................................................... p. 16Air filter .............................................................................................................. p. 17Cyclone prefilter ................................................................................................. p. 17Engine running-in ............................................................................................... p. 17
ELECTRONIC HYDROSTATIC TRANSMISSION .............................................. p. 18Example of a closed loop hydrostatic transmission ............................................ p. 19Operation of the variable displacement pump with axial pistons ......................... p. 20Operation of the electronic hydrostatic system ................................................... p. 21Description of the main functions ....................................................................... p. 22
HYDRAULIC DIAGRAM ...................................................................................... p. 24
HYDROSTATIC PUMP ......................................................................................... p. 26
HYDRAULIC MOTOR........................................................................................... p. 28HYDROSTATIC TRANSMISSION MAINTENANCE............................................... p. 30
Replacing the filter and changing the transmission oil ......................................... p. 30
BRAKES ............................................................................................................. p. 31Diagram of the service brake and the parking brake systems ............................ p. 31Checking the service brake ............................................................................... p. 32Releasing the brakes for towing of the truck....................................................... p. 32
ELECTRIC SYSTEM ............................................................................................ p. 33Battery ............................................................................................................... p. 33Electric components .......................................................................................... p. 34Fuse holding panel ............................................................................................ p. 34
SERVICE MANUALpage 5
INTERNALCOMBUSTION
2,5 - 3,0 - 3,5 t
Engine actuator ................................................................................................. p. 35Potentiometer and microswitches ...................................................................... p. 35Rotary / Linear potentiometer ............................................................................. p. 36Wiring diagrams ................................................................................................ p. 37
MENUS AND PARAMETERS FOR THE TCS SYSTEM ..................................... p. 39
CALIBRATION ..................................................................................................... p. 40Calibration and first start up of the transmission system ..................................... p. 42
DISPLAY.............................................................................................................. p. 45PUMP CUSTOMIZED .......................................................................................... p. 46ENGINE CUSTOMIZED ....................................................................................... p. 47FAULT DETECTED ............................................................................................. p. 48INFORMATION / PH PARAMETERS .................................................................... p. 49EPROM RESET .................................................................................................. P. 50
Troubles occuring while calibrating ...................................................................... p. 50System faults and failures .................................................................................. p. 56Troubleshooting ................................................................................................. p. 58
WHEELS / TYRES .............................................................................................. p. 59Safety of wheels and rims while using the truck .................................................. p. 59
STEERING UNIT ................................................................................................ p. 60Steering control ................................................................................................. p. 60Steering axle ..................................................................................................... p. 61Bearings adjustment .......................................................................................... p. 62
HYDRAULIC DISTRIBUTOR ............................................................................. p. 63
MASTS ................................................................................................................ p. 64Description of the cylinder components .............................................................. p. 66Cylinder inspection procedures.......................................................................... p. 67Lubrication ........................................................................................................ p. 68Installation checks safety specifications ............................................................. p. 69Safety limit stops of the fork mounting carriages ................................................ p. 69Chains inspection .............................................................................................. p. 70Fork inspection ................................................................................................. p. 70
LIFTING THE TRUCK ........................................................................................ p. 71Hooking points .................................................................................................. p. 71
TABLES .............................................................................................................. p. 72Table for oil and grease specifications................................................................ p. 72Table for the truck maintenance during the running-in stage ................................ p. 73Table for the maintenance schedule ................................................................... p. 74
SE
RV
ICE
MA
NU
AL
page 6
2,5 - 3,0 - 3,5 tIN
TE
RN
AL
CO
MB
US
TIO
N
TE
CH
NIC
AL
DA
TA
SERVICE MANUALpage 7
INTERNALCOMBUSTION
2,5 - 3,0 - 3,5 t
SERVICE MANUALpage 8
2,5 - 3,0 - 3,5 tINTERNAL
COMBUSTION
FOOT PEDALS VERSION
Pedals consist of:- two travel pedals, one forward pedal (A)
and one reverse pedal (B)- a service brake pedal (C)
One travel pedal (E)
HAND DIRECTION LEVER VERSION
Lever of direction selector (D)
1 forward speed0 neutral2 reverse speed
1
o2
�
�
o
D
CB
A
EC
G
C F
BALANCED PEDAL VERSIONForward pedal (F)Reverse pedal (G)Brake pedal (C)
SERVICE BRAKEFoot service brake (C) controls a hydrostatic brakingin the first part of the stroke by means of the electroniccontrol unit; if fully pressed, it engages the oil-bath discbrakes (over the front driving wheels).
SERVICE MANUALpage 9
INTERNALCOMBUSTION
2,5 - 3,0 - 3,5 t
DASHBOARDDuring ordinary operation, all warning lights in the dashboard are to be off.
9 13121110
15
14
865 74321
1 2
4
3
1) Fuel gauge2) Water temperature indicator3) Fuel level warning light4) Generator warning light5) Glow plug warning light (Diesel engine)6) Parking brake-on warning light7) Oil pressure warning light8) Indicator light (optional)9) Electronic hour counter10)Water temperature warning light11)Transmission oil temperature warning light12)Hydraulic oil filter clogged warning light13)Warning light (not used)14)Warning light (not used)15)Warning light indicating air filter clogged
A) Parking switch;B) Electronic failure warning light
If the warning light blinks during ordinary operation, this indicatesa failure in the electronic control unit; the vehicle will stop.
C) Ignition keyD) Emergency push-button; it acts as an emergency brake.
CAUTIONThe vehicle could instantaneously stop if buttons (A) and (D)are pressed; never press those buttons during the truck ordinaryoperation.
DASHBOARD INDICATORS1) Fuel gauge
2) Coolant temperature levelIndicates the coolant temperature.The pointer must never reach the red sector; the working temperaturecorresponds to 95 °C.
3) Fuel level warning lightThe fuel level warning light turns on when approx. 5.5 l of fuelare left in the tank.
4) Generator warning lightThat warning light is to be off when the engine is running. If not,it indicates that the alternator does not supply any current for thebattery or the electric system charge. This may be caused by thebreaking of the belt that drives the alternator pulley, or by a failureof the alternator.
D
BC
A
SERVICE MANUALpage 10
2,5 - 3,0 - 3,5 tINTERNAL
COMBUSTION
5) Glow plug warning light (Diesel engine).This warning light turns on when the ignition key is in position (2);
6) Parking brake on warning light
7) Engine oil pressure warning lightDuring ordinary operation, this warning light is to be off.If it turns on, immediately check the oil level in the engine. That warninglight could turn on when the engine is idling and hot, due to a lesserlubricant viscosity, even if no failure has occurred.
8) Direction indicator on warning light (optional)
9) Electronic hour counterIt indicates the working hours and hour fractions of your truck; it is controlledby the contact key and has the function to simplify scheduled maintenanceprogramming.
10)Coolant temperature warning lightIt indicates the engine overheating. Should it turn on, stop the vehicleimmediately.Check the correct operation of the radiator fan, the water pump and thecoolant level in the radiator.
11)Transmission oil temperature warning lightIt indicates that the temperature limits required for the correct operationof the pump and the hydrostatic engine have been exceeded.Should it turn on, stop working and determine the reasons for the overtemperaturetransmission oil.Check the oil level and that the radiator is clean and in good operatingconditions.
12)Transmission oil filter clogged warning light (replace filter)
13)Warning light (not used)
14)Warning light (not used)
15)Air filter clogged warning light (replace filter)
8
7
9
10
11
5
6
12
13
14
15
SERVICE MANUALpage 11
INTERNALCOMBUSTION
2,5 - 3,0 - 3,5 t
A: PARKING SWITCHB: ELECTRONIC FAILURE WARNING LIGHT
position 1 - Travel enabledSwitch A in position 1 enables the truck to travel (greenwarning light B and warning light 6 on the dashboard are on);brakes are engaged, but will automatically be released if the controlpedal is pressed (warning lights B and 6 turn off).
position 2 - Parking - start upSwitch A in position 2 (green warning light B off) starting ofthe engine is possible. Travel blocked to prevent any accidents. Brakes are engaged (parking condition).
HYDROSTATIC BRAKINGLift the travel pedals or the accelerator to enable the hydrostatic braking(adjustable) until the truck stops.The brakes are engaged if the control pedals are not actuated within a short period of time. When reoperating the control pedal, brakeswill be automatically be released.
TRUCK START UP
- the operator must be seated- parking switch A in position 2 (parking)- turn the key to position 1 (ignition on)- turn the key to position 2 (glow plugs on)- turn the key to position 3 (starter contact) to start the engine- once the engine has started up, turn the parking switch
A to position 1.- select the foward or reverse direction. The truck is ready to travel.
If the start up procedure has not been correctly performed, the truckwill not start up. If so, repeat the procedure above.
1 2
B
A
2
1
B
A
SERVICE MANUALpage 12
2,5 - 3,0 - 3,5 tINTERNAL
COMBUSTION
A B
CAPACITY PLATE
ATTACHMENT OR SPECIAL CONDITION OF USE
TYRES SERIAL N°
CENTER OF LOAD DISTANCE mmLIFT HEIGHTmm
DERATED CAPACITY Kg
Co
d. 0
3120
05
Co
d. 0
3120
04
CARRELLI ELEVATORI S.p.A.via Persicetana vecchia, 10
40132 - Bologna - Italia
MODEL Type MOTOR RATED CAPACITY
SERIAL N° DRAW-BAR PULL (1h)
SERVICE MASSBATTERY MASS
MANUFACT. YEAR TENSION
kW kg
N
WithoutBattery kg
kgmin.
kgmax.
V
J
SET OF LEVERS - LOAD HANDLING
K) Lifting control (yellow).L) Tilt control lever (green).M)Control lever of the sideshift or other devices (red).N) Available (if existing; black)
OPENING ENGINE COMPARTMENT COVER
Before lifting the engine compartment cover, turn the ignition key topos.0.Unlock with the key (I) and turn the handle (C).Lift the cover by using the special handle (L)An air spring (J) facilitates the complete lifting of the cowling.
LOAD PLATEIt identifies the load capacity with a load centerof 500 mm (except for different indications) IDENTIFICATION PLATE
It identifies the lift truck technical data
CESAB LDTBevan Way
Smethwick - WarleyWest Midla 1ds B66 1BZ
K
L
M
N
C
L
I
SERVICE MANUALpage 13
INTERNALCOMBUSTION
2,5 - 3,0 - 3,5 t
ENGINE KUBOTA 3300 - E
1 - Intake manifold2 - Speed control lever3 - Engine stop lever4 - Shut off solenoid5 - Fuel feed pump6 - Cooling fan7 - Engine hook8 - Oil filter cartridge9 - Fuel filter plug
10 - Oil filler plug11 - Exhaust manifold12 - Alternator13 - Starter14 - Fan belt15 - Oil pressure switch16 - Flywheel17 - Oil drain plug18 - Oil pan
SERVICE MANUALpage 14
2,5 - 3,0 - 3,5 tINTERNAL
COMBUSTION
KUBOTA V 3300 ENGINE
No. cylinders 4 in line
Bore 98 mm
Travel 110 mm
Swept volume 3318 cm‡
Compression ratio 22,6:1
SAE J1349 power 46 kW
Maximum torque230 Nm
at 1600 rpm
Maximum speed (withload)
2200 rpm
Cooling water
Injection indirect
Injection pump in line
Induction atmospheric
Electrical system 12 V
Lubrication forced
Oil sump (capacity)13,2 L
including filter
Alternator 540 W - 45 A
Starter motor 2.5 kW
SERVICE MANUALpage 15
INTERNALCOMBUSTION
2,5 - 3,0 - 3,5 t
CONTINENTAL TM 27 ENGINE
No. cylinders 4 in line
Bore 91 mm
Travel 103,5 mm
Swept volume 2700 cm‡
Compression ratio 8:1
SAE J1349 power 43 kW
Maximum torque200 Nm
at 1500 rpm
Maximum speed (withload)
2400 rpm2200 rpm
Cooling water
Feeding LPG
Induction atmospheric
Electrical system 12 V
Lubrication forced
Oil sump (capacity) 4 L
Alternator 12 V - 65 A
Starter motor 1.4 kW
SERVICE MANUALpage 16
2,5 - 3,0 - 3,5 tINTERNAL
COMBUSTION
OIL CHANGE AND ENGINE OIL FILTER REPLACEMENT
The oil level in the sump is checked with the dip-stick, making sure that the level isbetween the MIN and MAX notches.If it is necessary to top up, use the same oil as that used for filling.
CHANGING OIL AND FILTERAfter the first 50 hours: change oil and filter of the engineand thenevery 50 hours: check oil engine levelevery 250 hours: change oil and filter of the engine
To replace the oil and the filter, proceed as follows:-with the engine hot, remove filling cap, then unscrew the drain plug and allow the oilto drain out.-Unscrew the engine filter cartridge.-Fit the new filter and tighten it, paying particular attention to the position of the seal thatshould be previously oiled.-Tighten the drain plug and fill the oil sump up to the Max level on the dip-stick.
TOPPING UP WITH COOLANT
Every 50 hours- Make sure the coolant level is up to the radiator cap (B).
The caps of the tank and radiator must be removed only whenthe engine is cold.
Every 250 hours- clean the radiator outside.
Every 2000 hours- replace the coolant mixture; check the freezing point of the coolant mixture, especially whendriving areas with cold weather.
The truck is supplied with a 50% mixture of coolant. If you want to varythe mixture, refer to the values stated in the table below.
B
ANTIFREEZE APPLICATION RANGE
10% 20% 30% 40% 50% % VOLUME OF ANTIFREEZE
-4 C -10 C -17 C -24 C -40 C FREEZING TEMPERATURE
101 C 102 C 104 C 106 C 109 C BOILING TEMPERATURE
SERVICE MANUALpage 17
INTERNALCOMBUSTION
2,5 - 3,0 - 3,5 t
AIR FILTER
The air suction filter for the fuel supply is composed of two filteringelements.Every 250 hours- Clean the element outside the filter (the element inside is not to becleaned).The filter is to be cleaned also when relevant warning light (15) onthe dashboard turns on.Every 3 cleaning cycles- replace the element inside the filterEvery 6 cleaning cycles, or once a year- replace the element outside the filter.
Disassembling and cleaning the filter- release the cover fastening screws and remove the filter cartridge;- clean with compressed air (MAX. 5 bar pressure) from the insidetowards the outside;- check that no tear is to be found.Never hit the cartridge on hard surfaces.Never use any mixture of water and detergent to clean thefilter.
When reassembling the filter cover, make sure that the dustemptying opening is turned downwards.
CYLONE PREFILTER
Every 8 hours- clean the cyclone prefilter.
Cleaning the cyclone prefilter- loosen wing-nut (A);- remove cover (B);- remove tank (C);- empty the tank and reassemble.
ENGINE RUNNING-INDuring the running-in period, the engine may consume more oil thanusual. It is recommended that the oil level be checked every 8 workinghours, with engine at stand still for at least 10 minutes.
Do not use the engine at its peak RPM until it has reached its workingtemperature.
A B
C
A
SERVICE MANUALpage 18
2,5 - 3,0 - 3,5 tINTERNAL
COMBUSTION
The control and adjustment of the electronic transmission are made bya control unit (Total Control System) that drives the following:· thermal engine· hydrostratic pump· hydraulic motors· parking brakes
by means of sensors:· potentiometers (on the accelerator pedal, the brake/inching pedal and the mast lever)· switches (on the tilt levers and sideshift, the forward/reverse gearshift lever and to engage the parking
brake)· potentiometer detecting the pump displacement· sensor of the thermal engine speed of rotationand by means of actuators:· proportional solenoid valves of the hydrostatic pump (displacement adjustment)· actuator on the thermal engine (adjustment of the fuel pump or the carburettor)· solenoid valve for the displacement shifting of the hydraulic motors· solenoid valve for the parking brakes release
HYDROSTATIC TRANSMISSION
Hydrostatic transmission consists of a variable displacement pump, which iscontrolled by the thermal engine and which delivers oil towards two hydraulicmotors that drive the front wheels.The hydraulic connections of both motors allow a proportional division of theoil flow generated by the hydrostatic transmission, so as to support the outerwheel while turning; that kind of transmission acts as the differential transmission.
PortableTerminal
Travel pedal
Parking brake switch
Potentiometer onmast lever
Thermal enginespeed sensor
Hydrostaticpump Thermal engine actuator
Solenoid valve for parkingbrake release
Failure warninglight
Running directionselector
Brake/inchingpedal
Control unit
SERVICE MANUALpage 19
INTERNALCOMBUSTION
2,5 - 3,0 - 3,5 t
circ
uit.t
if
EXAMPLE OF A CLOSED LOOP HYDROSTATIC TRANSMISSION
Basic system - pump / motor
An integrated auxiliary pump is used for restoring of the lost oil. The system is completedby an pressure reducing valve, to control the charge pressure.
The system is equipped with two max. pressure valves, one on each side of the high pressure circuit.There function is to protect the hydrostatic transmission (pump and motor) from overloads.
On the hydraulic motor, and on the pump there are some internal oil leakage (for lubrication and cooling). This oil is brought back to the tank.
SERVICE MANUALpage 20
2,5 - 3,0 - 3,5 tINTERNAL
COMBUSTION
The capacity of the pump is depending of the rpm, and of the displacement, which can be changed in continuity.By increasing the tilting of the plate, the capacity increases from 0, to the max. value.
On tilt 0°, it corresponds to 0 mmof stroke, therefore 0 capacity.(machine stopped)
If the tilting plate of the pump is positionedbeyond the neutral point, the oil flow directionwill be inverted.
OPERATION OF THE VARIABLE DISPLACEMENT PUMP WITH AXIALPISTONS
SERVICE MANUALpage 21
INTERNALCOMBUSTION
2,5 - 3,0 - 3,5 t
OPERATION OF THE ELECTRONIC HYDROSTATIC SYSTEM
1 Thermal engine2 Hydrostatic pump3 Hydraulic motors with built-in parking brake4 Boost pump (charge pump)5 Solenoid valves adjusting the pump displacement (proportionella > 0-5V)6 TCS control unit7 Accelerator pedal (0-5V)8 Direction selector (steering-wheel operated reverse gear with single pedal or acting directly on the
double/swaying pedal system)9 Actuator of the thermal engine10 Sensor for the motor speed of rotation11 Sensor for the hydrostatic pump displacement (magnet potentiometer)12 Brake pedal (0-5V, 0-95% av rörelsen=hydrostatbroms. 95-100% = parkeringsbroms)13 Solenoid valve to release the brakes on the motors14 Parking brake switch15 Fault warning light16 Service pump17 potentiometer/microswitches on the mast lever, the tilt system, the sideshift and any auxiliary
devices. (lyftpotentiometer > 0-5V)
15
4
10
9
113
3
1317
8
15
14
12
76
2 16
��
�
���������������
SERVICE MANUALpage 22
2,5 - 3,0 - 3,5 tINTERNAL
COMBUSTION
DESCRIPTION OF THE MAIN FUNCTIONS
TRUCK TRAVEL The thermal engine may only be started if the parking brake is on.The system allows the pump to increase the displacement (truck motion) only if:- the motor is running- the parking brake is off- the running selector is not in neutral position.Should one of those conditions not be true, the actuation of the accelerator pedal will onlyresult in thermal engine speeding up.
The position of the accelerator pedal - through the thermal engine and the hydrostatic pump -affects the truck speed, i.e. each position of the pedal potentiometer corresponds to thefollowing preset values, according to the setting values programmed in the control unit:- speed of the thermal engine- pump displacement.
ACCELERATION / DECELERATION The truck acceleration depends on the speedwith which the accelerator pedal is pressed and on the parameters set in the control unit.
BRAKING / INCHING The brake pedal has two functions: 1) hydrostatic braking (thepump displacement cancels itself out) with a strength depending on the pedal stroke; 2) “inching”function, that can be obtained by simultaneously pressing the brake pedal and the acceleratorpedal.
PUMP DISPLACEMENT The displacement of the hydrostatic pump depends on the strokeof the accelerator pedal (and on the stroke of the brake pedal in the “inching” function). Theaccelerator pedal also determines the rate of rotation of the thermal engine (by means of theactuator).
ANTISTALL FUNCTION During the truck ordinary operation, if the power required bythe hydrostatic transmission exceeds the power that may be supplied to the thermal engine,the pump displacement will be automatically reduced to avoid the engine to stall.
PARKING BRAKE The parking brake is engaged by pressing a switch located next to thedistributor levers. When the parking brake is on, the accelerator pedal is disabled (the thermalengine accelerates, but the truck cannot run). If the parking brake is engaged while the truckis running, the driving wheels will be automatically locked. Therefore, avoid engaging theparking brake while the truck is running, unless you are in an emergency condition.
CONSTANT SPEED When using the mast levers, tilt system and sideshift, the thermalengine automatically accelerates to meet the request for additional power; the pumpdisplacement will be simultaneously reduced to ensure that the truck speed is kept constant.
SERVICE MANUALpage 23
INTERNALCOMBUSTION
2,5 - 3,0 - 3,5 t
RUNNING DIRECTION May be selected through the steering-wheel operated reversegear (for simple pedals) or the forward/reverse pedals (for the double and swaying pedalsystem). If the lever of the steering-wheel operated reverse gear is shifted to the neutralposition while the truck is running (or the accelerator pedal is released in case of double pedalsystem), the truck will hydrostatically brake. If the running direction is reversed while thetruck is running, a hydrostatic braking will occur, which will be immediately followed by theacceleration in the opposite running direction.
PARAMETER SETTING Most part of the transmission operation parameters may be setvia portable terminal.
CALIBRATION The system sensors and actuators (pedals, motor actuator, etc.) are to becalibrated using the portable terminal.
FAULT DETECTION A warning light located beside the distributor lever indicates thesystem faults (the warning light starts blinking). If the failure concerns the hydrostatic pump,the truck will immediately stop.
DIAGNOSTICS The portable terminal, which is connected to the control unit, allows todetect and to store any system fault.
DISPLAY The display of the portable terminal allows to view the information about thetransmission operation (thermal engine speed, pump displacement, and so on).
THERMAL ENGINE OPTIMIZATION The thermal engine operation (rate of rotation)is optimized according to the truck speed the operator needs.
SPEED DECREASE (OPTIONAL) The truck speed may be decreased for example incase of transmission oil overtemperature.
Exchange valve, 19bar
OljefilterH
YD
RA
UL
IC D
IAG
RA
M
MagnetventilBroms
Prioriterings-ventil
OrbitrolStyrning
Gaspedal
Fram&Back
Broms
S
(återfyllnad av systemet, kompensation för läckolja)
A A=Bypasskruv för bogsering
SERVICE MANUALpage 25
INTERNALCOMBUSTION
2,5 - 3,0 - 3,5 t
HIGH PRESSURE CIRCUIT
LOW PRESSURE CIRCUIT
BY-PASS VALVE2 BAR
RETURNLIFTINGOIL
TRANSMISSIONSUCTION
AUXILIARY SERVICECHECKING POINT
DRAINAGEMOTEURS
RETURNTRANSMISSIONOIL
�
��
�
�
�
�
LIFTINGSUCTION
EXCHANGE VALVE
OIL RETURN TOTANK
NEGATIVE BRAKEELECTROVALVE
BOOST PRESSURE CHECK POINT
�
� �
��
�
HIGH PRESSURE CHECK POINT
HIGH PRESSURE CHECK POINT
TEMP
SERVICE MANUALpage 26
2,5 - 3,0 - 3,5 tINTERNAL
COMBUSTION
The pump displacement is controlled by two proportional solenoid valves which are fed bythe boost pressure and controlled by the control unit through an electric signal. The spool shiftof the solenoid valves controls the pressure over the two chambers of a piston servocontrolthat is mechanically coupled to the pump plate; the difference in pressure between the twochambers determines the piston shift, i.e. the displacement shifting.The pump displacement is then detected by a rotary potentiometer sending a signal proportionalto the plate shift.The electric control through the solenoid valves and the potentiometer represents a feedbackedcircuit for the adjustment of the pump displacement.A sensor detecting the speed of rotation is to be found as well.
HYDROSTATIC PUMP
PUMP Mod. POCLAIN PV75 SA (Eaton, USA)Displacement 75.5 cc/revBoost pump displacement 13.9 cc/revMax. pressure measured in M1 or M2 (stall) 450 BarBoost pressure measured in M3 24-30 BarDrain pressure measured in T1 or T2 max. 5 Bar(cold pump) or after temperature stabilization max. 2.8 BarVacuum pressure (absolute pr., measured in S) 0.8 Bar
EXCHANGE UNITValve setting 19 Bar
Boost pump
Solenoid valves
Actuator
Hydrostaticpump
Pump displacementpotentiometer
Displacement adjustingplate
To motors
SE
RV
ICE
MA
NU
AL
page 27
INT
ER
NA
LC
OM
BU
ST
ION
2,5 - 3,0 - 3,5 t
DRAIN INLETT1
(from the exchange unit)
1 1/16 - 12 UN - 2B
POTENTIOMETERMEASURING THE PUMP
DISPLACEMENT POTENTIOMETERCONNECTOR
M
2
M
3
M
1
BHIGH PRESSURE
MOTORSIDE
PROPORTIONALSERVOVALVES FORTHE DISPLACEMENTADJUSTMENT S
CHARGE PUMP INLET PORT(FROM THE OIL FIL
TER)1 5/16 - 12 UN - 2B
SERVOVALVE CONNECTORSENSOR FOR THE SPEED OFR
O
T
A
TION
DRAIN OUTLETT2
(to the radiator)
1 1/16 - 12 UN - 2B
HIGH PRESSURE DETECTION SOCKETM 2 9/16 - 18 UNF - 2B
BOOST PRESSURE SOCKETM 3 7/8 - 14 UN - 2B
HIGH PRESSURE DETECTION SOCKETM 1 9/16 - 18 UNF - 2B
BOOST V
A
L
V
E
S
E
R
V
O
V
A
L
VE PRESSURE SOCKET 2M 5
7/16 - 20 UNF - 2B
AHIGH PRESSURE
(to motors)
S
E
R
V
O
V
A
L
VE PRESSURE SOCKET 1M 4
7/16 - 20 UNF - 2B
MECHANICAL ZEROADJUSTMENT
< 0-5V (2,5V i mittläget)
SERVICE MANUALpage 28
2,5 - 3,0 - 3,5 tINTERNAL
COMBUSTION
HYDRAULIC MOTOR
Motors Poclain MS 05 (radial pistons)
Maximum displacement 468 cc/revMaximum pressure 450 BarTheoretical torque 740 NmMaximum speed 240 RPMBrake multidisc typeBraking torque max. 3060 NmNumber of pistons 8Brake driving pressure (measured in x) 12-30 BarDisplacement shifting driving pressure (measured in y) 10-30 BarDrain pressure (measured in 1) with cold motor max. 3 Bar
after temperature stabilization max. 1.5 Bar
wheelhub
cylinderunit
distributor brake
SERVICE MANUALpage 29
INTERNALCOMBUSTION
2,5 - 3,0 - 3,5 t
The hydraulic motor is of “slow” type. Due to its radialpistons, it is characterized by a high displacement/rev (ifcompared to engines with axial pistons) so it produces ahigh torque at a low speed rate, with no reduction gearbetween the engine and the wheel hub.
The engine is also equipped with an oil-bath multidisc brake that is normally engaged(wheel locked) by the pre-load of a Belleville washer (negative brake); the brake ishydraulically released by means of a solenoid valve controlled by the control unit: whenthe solenoid is fed, the valve opens and the fuel boost pressure on the brake pistonreleases the brake.The multidisc brake on the motor is used only for the truck parking and emergencybraking; on the other hand, service breaking is a hydrostatic one.The motor-brake unit is fully lubricated by the transmission oil (oil dripping from thehydraulic motor).
Braking release hole- M12 x 1,75
R, L High pression inlet - 3/4 GAS1 Drain hole 3/8 GASX Negative brake pilote 1/4 GAS
SERVICE MANUALpage 30
2,5 - 3,0 - 3,5 tINTERNAL
COMBUSTION
HYDROSTATIC TRANSMISSION MAINTENANCE
The transmission system and hoisting system have the same oil tank, which is provided with onefilter.
�
T
Components of the transmission system:A) Oil level dipstickB) Oil bleeding holeC) Hydraulic oil filter unitD) Oil filling hole
Maintenance consists of the oil change and filter replacement inorder to keep the circuit clean.
REPLACING THE FILTER AND CHANGING THETRANSMISSION OILAfter 50 hours
- First transmission filter replacement.After 500 hours
- Second transmission filter replacement;- First oil change for the transmission/hoisting systems.
Then, every 2,000 hours- transmission filter replacement;- oil change for the transmission/hoisting systems.
The oil change is to be performed once a year. The filter is to be changed also when it getsclogged - warning light (12) on the dashboard on; in that case, replace the filter cartridgeimmediately.
To replace the filter, do the following:- re move plug (C) and extract the filter- insert the new cartridge and close.
To change the oil in the tank for the transmission and hoisting systems, do the following:- change the oil while the engine is still hot;- remove plugs (A) (C) and (T) and let the fluid flow out;- carefully clean the oil tank;- fill the tank with clean oil up to the max. level marked on dipstick (A) after fastening drain plug (T).- only use the oil types mentioned in the specifications section in this manual;- do not use oil that deteriorated due to a long storage.
After replacing the filter and changing the transmission oil:- start up the engine, let it idle for about 5-10 minutes while the vehicle is standstill;- check the oil level; top up, when required.
A CB D
SERVICE MANUALpage 31
INTERNALCOMBUSTION
2,5 - 3,0 - 3,5 t
BRAKES
The brake pedal has two different functions:- braking (if it is used alone)- “inching” function if it is used simultaneously with the accelerator pedal.
The brake pedal stroke is divided into two configurable intervals:0 to 95 % of the whole stroke: hydrostatic braking. The control unit reduces the pumpdisplacement according to a programmed ramp. The braking effect is proportional to thepedal stroke.95 to 100 % of the whole stroke: mechanical braking. The pump displacement cancels itself out in about 1.5 secs and the negative brakes get engaged.
During ordinary operation, if the truck is slowed down and stopped, the mechanical brakesact automatically (after approx. 0.5 secs) on motors. Press the accelerator pedal again torelease the brake and to speed up.When the mechanical brake is engaged, the relevant warning light on the dashboard turns on.
The braking effect may also be obtained by releasing the accelerator pedal (hydrostatic braking)or by reversing the running direction (hydrostatic reverse braking, more efficient than the merehydrostatic braking).
DIAGRAM OF THE SERVICE BRAKEAND PARKING BRAKE SYSTEMS
A) Hydraulic motorB) Brake unitC) Solenoid valveD) TankE) Electronic control unitF) Hydrostatic transmissionG) Service brake pedalH) Parking switchI) Potentiometer
Every 4,000 hours- replace solenoid valve (C) for the brake control.
Every 10,000 hours- replace brake hoses (S).
B
C
F
D
E
G
H
A
I
SS
S
H
SERVICE MANUALpage 32
2,5 - 3,0 - 3,5 tINTERNAL
COMBUSTION
LN O
M
CHECKING THE SERVICE BRAKE
The disc brakes are in oil-bath; they make use of the same oil as the traction hydraulicmotors.
The disc brake unit is composed of 11 discs and 11 counterdiscs. The total discthickness is: min. 27 mm, max. 34 mm.
Every 250 hours- check the pedal operation; the pedal has to be free from any obstacle;- check the brake wear;
RELEASING THE BRAKES FOR THE TRUCK TOWING
In case of breakdown, previously release the brake discs inside the two traction unitsto tow the truck.
Brake releasePosition appropriate tool (M), code 1996086 (M12 x 1,75), one for each brake unit;tighten screw (N) into hole (L) on the brake unit; keep tool (M) locked and tightennut (O) until the brakes unlock.
SERVICE MANUALpage 33
INTERNALCOMBUSTION
2,5 - 3,0 - 3,5 t
P
Q
ELECTRIC SYSTEM
Every 500 hours- check the push-buttons wiring and operation;- check the operation of the microswitches located on the pedals;
Every 1000 hours- inspect wiring and connections; check if the cable terminals are properly tightened
and the cable insulation is intact.
WARNING:DISCONNECT THE TRUCK BATTERY BEFORE SERVICINGTHE ELECTRIC SYSTEM AND THE ELECTRONIC EQUIPMENT.
BATTERYBattery (P) is located under the engine bonnet; before servicing, alwaysdisconnect safety connector (Q).Every 500 hours
- clean the battery poles and terminals;- grease and tighten the terminals;
Every 1,000 hours- check the earth connections.
Every 4,000 hours- replace the battery.
The battery supplied has a min. 100 Ah capacitance.
If the battery is a maintenance-free one, inspect as follows:
Every 50 hours- check the electrolyte level and density; top up with distilled water,
if necessary.The battery is to be recharged when its voltage has decreased by1.7V or the electrolyte thickness is under 1.16 kg/dm3.
When the truck is running, never disconnect the battery cables,so as to avoid dangerous voltage peaks to the alternator diodes.
SERVICE MANUALpage 34
2,5 - 3,0 - 3,5 tINTERNAL
COMBUSTION
ELECTRIC COMPONENTS
FUSE HOLDING PANELLift the engine bonnet to reach to the fuse panel, which is located below the support of the distributorcontrols.The panel is composed of a fuse block (A), of some relays (B) and optional intermittance (C).Disassemble the protecting panel to replace the component.
Fuse specifications1 F1 alternator, starter 40A2 F2 horn 5 A5 F5 system protection 7.5 A7 F7 alternator 7.5 A8 F8 engine stop 5 A11 F11 glow plug 5 A15 F15 rear lights - reverse light 5 A16- F16-rear lights - brake/stop light 5 Athe other fuses are intended for optional systems
Before replacing a fuse, make sure that the problem generating fuse burning has been solved.
RelaysE1 - start upE2 - brake validationE3 - glow plug warning light (diesel engine)E4 - reverse speed validationE5 - forward speed validationE6 - brake/stop rear lightE8 - reverse rear light
the other fuses are intended for optional systems
A
CB
RELAIS TYPE RELAIS TYPE
CODE CODE
E3-E4-E5-E6-E8-E9 E1-E2
SERVICE MANUALpage 35
INTERNALCOMBUSTION
2,5 - 3,0 - 3,5 t
ENGINE ACTUATOR
The engine actuator is controlled by TCS control unit; it adjusts the Diesel engine injection pump.The engine actuator is composed of an electric motor controlling the control shaft of the pump tierod and of a potentiometer detecting the shaft rotation and generating a feedback electric signal(voltage).When calibrating, the control unit correlates the actuator stroke (rotation) measured by thepotentiometer with the thermal engine speed of rotation, measured by the sensor located on thehydrostatic pump. The unit composed of the actuator and the rev sensor is a feedback systemintended for adjusting the engine speed.
WARNING - POTENTIOMETERS AND MICROSWITCHES
To avoid compromising the functional characters of the truck, fixing or adjusting of the potentiometers(D), the micrositches (B), the mechanical stops (C) and the accelerator control tie-rod (D), isforbidden.
BLU
E
BLA
CK
BR
OW
N
RE
D
YE
LLO
W
A
C
C
A B
C
C B
DC
C
BRAKE PEDALTRAVEL PEDAL
SERVICE MANUALpage 36
2,5 - 3,0 - 3,5 tINTERNAL
COMBUSTION
ROTARY POTENTIOMETER(on the accelerator and brake pedals) resistance: 2.5 kohm
electric stroke: 54°mechanical stroke: 60°
LINEAR POTENTIOMETER(on the mast lever) resistance: 5 kohm
electric stroke: 10 mmmechanical stroke: 12.5 mm
AMP CONNECTOR type: 144-796-1(on control unit) 55-pin
redgreen
yellow
yellow
red
green
Page 37
Page 38
SERVICE MANUALpage 39
INTERNALCOMBUSTION
2,5 - 3,0 - 3,5 t
MENUS AND PARAMETERS FOR THE TCSSYSTEM
The parameters for the transmission control are composed of submenus and may be viewedand modified through the portable terminal (code 0058039), that may be connected to thecontrol unit .
The [ENTER] key is used for selecting a menu or submenu and for the confirmation of aparameter numeric value.
The [ESC] key is used for quitting a menu or submenu or for deleting the last characterentered.
The [+] and [-] keys are used for moving through the menu list or increasing and decreasingthe numeric value of a parameter.
Use the numeric keypad to enter the parameter values; use the [.] key for decimal places.
För att programmera en lös TCS-box:
Anslut Pin 19 och 37 till B+Anslut Pin 18 och 55 till B-
SERVICE MANUALpage 40
2,5 - 3,0 - 3,5 tINTERNAL
COMBUSTION
The main menus are listed below:
N. Menu Functions
1 CALIBRATION to calibrate potentiometers and transmission actuators (pedals,distributor, engine actuator, ...)
2 DISPLAY to display the information on the transmission (thermal engine speed,pump displacement, antistall function, ...)
3 PUMP CUSTOMIZED to customize the transmission (more or less prompt breaking andacceleration)
4 ENGINE CUSTOMIZED to customatize the thermal engine control (higher or lower accelerationof the thermal engine, engine speed when the tilt system and thesideshift are on, ...)
5 FAULT DETECTED to display the system faults6 INFORMATION software versions7 PH PARAMETERS (password) configuration of the system operation parameters8 EEPROM RESET (password) to reset the control unit memory
1) CALIBRATION
The CALIBRATION menu is used. That menu has two functions:
· when the parking brake is locked and the “calibration status” parameter is “not locked” , it allows thecalibration and configuration of the system elements (calibrating mode);
· when the parking brake is not locked or the “calibration status” parameter is “locked”, that menuallows to view the output voltages of the system sensors and the state of some components (display mode).
After any calibration, release and engage the parking brake again to exit from the “calibration status” mode andreturn to the standard operating mode.
SERVICE MANUALpage 41
INTERNALCOMBUSTION
2,5 - 3,0 - 3,5 t
CALIBRATION MENU
N. SUBMENU CALIBRATION MODE DISPLAY MODEA travel pedal calibration of the travel pedal display of the voltage supplied by the
potentiometer for the travel pedalB brake/inching calibration of the brake pedal display of the voltage supplied by the
pedal potentiometer for the brake pedalC mast lever calibration of the mast lever display of the voltage supplied by the
potentiometer for the mast leverD engine calibration calibration of the actuator-thermal display of the voltage supplied by the
engine potentiometer for the actuatorE pump neutral calibration of the pump in neutral display of the voltage supplied by the
position potentiometer for the hydrostatic pumpF max. forward limiting of the truck max. display of the truck forward speed
speed forward speed (as a percentage of the max. speed)G max. reverse limiting of the truck max. display of the truck reverse speed
speed reverse speed (as a percentage of the max. speed)H parking brake set definition of the brake pedal displays the brake pedal position in which
position in which the mechanical the mechanical brake is lockedpedal is engaged
I min engine speed definition of the minimum engine displays the minimun engine RPMRPM (tomgång)
L max engine speed definition of the maximum engine displays the maximum engine RPMRPM (fullvarv)
M pump pot. inverted definition of the connections type displays the connections type(*) of the pump potentiometer of the pump potentiometerN calibration status lock or unlock the calibration status of the calibration menu
menu
(*) With Hall potentiometer software only
For the TCS correct operation, the voltage values read by the potentiometers in the pedals, the mastsystem and the motor actuator must not exceed the limits set. If the mechanical limit stops of thepotentiometer are not properly adjusted, the voltage supplied by the potentiometers and exceedingthe range of values allowed by the control unit disables the calibration procedure.That trouble may also occur after a correct calibration if, for whatever reason, the limit stop ismodified.
SERVICE MANUALpage 42
2,5 - 3,0 - 3,5 tINTERNAL
COMBUSTION
CALIBRATION AND FIRST START UP OF THE TRANSMISSION SYSTEM
The system calibration is to be performed when the thermal engine is stopped. The following are to be calibrated:
· Potentiometer for the travel pedal (TRAVEL PEDAL)· Potentiometer for the brake pedal (BRAKE/INCHING PEDAL)· Potentiometer for the mast lever (MAST LEVER)· Feedback potentiometer for the hydrostatic pump (PUMP NEUTRAL)
While calibrating, check the parameters below:· Max. forward speed (truck max. speed) 100 %· Max. reverse speed (truck max. speed) 100 %· Parking brake set (brake setting) 95 %· Min engine speed (minimum engine RPM) 850· Max engine speed (maximum engine RPM) 2250· Pump pot. inverted (with potentiometer Hall effect only) Enable
Calibration also includes the actuator setting while the thermal engine is running (ENGINE CALIBRATION). Forthe engine calibration, do the following:
· Lift the truck onto the shim blocks· Fill the hydraulic circuit and bleed the air· Engage the parking brake· Select the neutral position (through the steering-wheel operated reverse gear)· Start up the engine and wait for the stabilization of the fuel boost pressure· Adjust the engine min. and max. RPM through the actuator limit stop screws (the limit stops are to be obtained
on the actuator support, not on the injection pump). The engine RPM is to be measured through the “enginespeed” parameter in the “DISPLAY” menu.
· Calibrate the actuator (ENGINE CALIBRATION)· Press the accelerator pedal; the actuator has to rotate clockwise and the voltage of the feedback potentiometer
in the actuator has to increase (such voltage may be measured in the “engine calibration” parameter in the“calibration” menu after engaging the parking brake).
Once the calibration procedure is over, check the transmission operation (wheels must be up):· Release the parking brake· Position the steering-wheel operated reverse gear to forward gear· Gradually press the forward pedal: wheels should slowly rotate forwards.
CAUTION: the hydraulic motors must not rotate quickly when wheels are up.When wheels rotate forwards, check that the voltage of the pump feedback potentiometer increases from 2.5 to5 volts (for the voltage detection, use “pump neutral” parameter in the “calibration” menu).Check the correct operation under the following conditions:
- mast lifting, sideshift and tilt operation, etc.: if the relevant levers are adjusted, the thermal enginewill accelerate.- forward/reverse speed and braking- parking brake: if engaged, the travel pedal will be disabled (the engine RPM will increase, but the truckwheels will be locked)
- emergency button.
SERVICE MANUALpage 43
INTERNALCOMBUSTION
2,5 - 3,0 - 3,5 t
A) TRAVEL PEDAL CALIBRATION
For calibrating, voltages are not to exceed the following ranges (voltages may be detected in display mode):
pedal in its min. position 0,35 - 2,4 volts (7 - 48 % of the supply voltage)pedal in its max. position 2,6 - 4,65 volts (52 - 93 % of the supply voltage)(the supply voltage of all sensors is of 5 Volts)
SEE THE “DIAGRAM FOR USING CONSOLE”SECTION “CALIBRATION”
B) BRAKE / INCHING CALIBRATION
Allows to define the voltage values corresponding to the min. and max. positions of the brake pedal (and the“inching” function).
For calibrating, voltages are not to exceed the following ranges:
pedal in its min. position 0,35 - 2,4 volts (7 - 48 % of the supply voltage)pedal in its max. position 2,6 - 4,65 volts (52 - 93 % of the supply voltage)
SEE THE “DIAGRAM FOR USING CONSOLE”SECTION “CALIBRATION”
C) MAST LEVER CALIBRATION
Allows to define the voltage values corresponding to the maximum and minimum positions of the mast lever.
For calibrating, voltages are not to exceed the following ranges:
lever in neutral position 0,35 - 2,3volts (7 - 46 % of the supply voltage)lever fully pulled 2,4 - 4,65 volts (48 - 93 % of the supply voltage)
SEE THE “DIAGRAM FOR USING CONSOLE”SECTION “CALIBRATION”
D) ENGINE CALIBRATION
Allows to match the actuator angular position (voltage of the actuator feedback potentiometer) with the enginespeed of rotation values.
For calibration, voltages are not to exceed the following ranges:
actuator in its min. position 0,35 - 2,4 volts (7 - 48 % of the supply voltage)actuator in its max. position 2,6 - 4,65 volts (52 - 93 % of the supply voltage)Such values may be viewed if the parking brake is engaged.
Vid 2-pedal system:Se till att max positionerna är lika för fram och back!
SERVICE MANUALpage 44
2,5 - 3,0 - 3,5 tINTERNAL
COMBUSTION
SEE THE “DIAGRAM FOR USING CONSOLE”SECTION “CALIBRATION”
The control unit automatically controls the actuator by bringing it to its minimum and maximum positions (that aredetermined by the mechanical limit stops located on the actuator support). With respect to the min. and max.positions, TCS reads the min. and max. RPM as well as some intermediate values.The limit stops are to be obtained on the actuator, not on the injection pump.
E) PUMP NEUTRAL CALIBRATION
Allows to define the voltage corresponding to the neutral displacement position of the hydrostatic pump (feedbackpotentiometer).
The voltage value must not exceed the following range: 2.49 to 2.51 volts.(In display mode and when the truck is running, the voltage value must vary. When the wheels rotate forwards, thepotentiometer voltage must tend to 5 Volts and remain constant).
SEE THE “DIAGRAM FOR USING CONSOLE”SECTION “CALIBRATION”
F) MAX FORWARD SPEEDThis parameter (expressed as a percentage of the truck forward max. speed) limits the travel speed. This parametermay be modified (in calibration mode).
G) MAX REVERSE SPEEDThis parameter (expressed as a percentage of the truck reverse max. speed) limits the travel speed. This parametermay be modified (in calibration mode).
H) PARKING BRAKE SETThis parameter defines the stroke of the brake pedal necesary to engage the mechanical brake. The standardvalue is 95%. It is suggested that this value be not changed. Limit values: 90 to 95%.
I) MIN ENGINE SPEEDThis parameter defines the minimum engine RPM (standard value 850).
L) MAX ENGINE SPEEDThis parameter defines the maximum engine RPM (standard value 2250).
M) PUMP POT. INVERTEDThis parameter defines the connections type of the pump potentiometer.This parameter is present with the Hall potentiometer software only.
N) CALIBRATION STATUSThis parameter enables or disables the calibration mode.
SERVICE MANUALpage 45
INTERNALCOMBUSTION
2,5 - 3,0 - 3,5 t
2) DISPLAY
This menu displays the transmission data.Press [ENTER] to display a data (e.g. thermal engine speed). Hold down the key to display data in sequence.
ENGINE SPEEDReal speed of the thermal engine (expressed in RPM). (9 pulser/varv)
PUMP DISPLACEMENTPump displacement required by TCS (expressed in cc). Warning: this is the displacement control sent by thecontrol unit to the pump, so the value displayed may be different from the real displacement.
ENGINE COMMANDSpeed of the thermal engine required by TCS (in RPM).
ANTISTALLIndicates whether the antistall function is enabled or not (enable/disable).
PARKING BRAKEDisplays whether the negative brakes are set or not (set/not set).
BRAKE SWITCHDisplays whether the parking brake switch is set or not (set/not set).
MAST ENGINE COMMANDSpeed of the thermal engine required by TCS (in RPM) when the mast is actuated.
PUMP FEED-BACKActual displacement of the pump (expressed in cc). This is the displacement measured by the potentiometerlocated on the pump.
DIRECTION SWITCHDisplays the running direction controlled by the pedal microswitches or the steering-wheel operated reversegear (neutral/forward/reverse).
MAST SWITCHDisplays the state of the distributor microswitches 1 = tilt/sideshift (set/not set).
CONSTANT SPEEDDisplays the constant speed function enabling when the mast is actuated while the truck is running (set/not set).
ACTUATOR FEED BACKDisplays the engine actuator signal in Volt. Increase during the acceleration and vice versa.
POWER SUPPLYDisplays the voltage supply of the contol unit: battey voltage (12 V). Must be between 9,5 and 48,5 Volt.
SENSOR EXCITATIONDisplays the voltage supply of the sensor. Correct value 5 Volt.
NEUTRAL DRIFTDisplays the value difference between the theorical and real pump potentiometer value (in mV).This parameter is present with the Hall potentiometer software only.
SERVICE MANUALpage 46
2,5 - 3,0 - 3,5 tINTERNAL
COMBUSTION
3) PUMP CUSTOMIZED
Allows setting of the parameters who controls the hydrostatic pump.These parameters is used to modify the acceleration and deceleration of the truck.First the modification of these parameters must enabled (calibration status - not locked).
TRAVEL PEDAL INC. (sekunder från neutral till full utvinkling)This parameter defines how long time it takes for the pump to reach its max. displacement when the travel pedal is fully pressed ( higher value of this parameter = softer acceleration of the truck).
TRAVEL PEDAL DEC. (sekunder från full utvinkling till neutral)This parameter defines how long time it takes for the pump to reach its neutral displacement mode when the travel pedal is released (higher value of this parameter = softer decceleration of the truck during thehydrostatic braking).
HARD BRAKING RATIOThis parameter (%) change the release braking value (travel pedal dec.) according to the following table:
Braking times of the truck function of the two parameters“Travel pedal dec” (s) and “Hard braking ratio” (%)
Travel pedal dec. (s) 2 5 7 10
Hard braking ratio (%)0 2 5 7 1017 1.7 3.8 5 6.550 - 2.8 - -67 1.6 2.5 3.1 3.683 - 2.3 - -100 1.3 2.1 2.5 2.9
SENSITIVITYThis parameter defines the sensitivity of the pump control when changing the pedal position (this value is expressed as a percentage of the pump max. displacement control).
INCHING PEDAL INC.This parameter defines how long time it takes for the pump to reach its max. displacement when the inching pedal is instantaneously released after it has been fully pressed in conjunction with the travel pedal.
INCHING PEDAL DEC.This parameter defines how long time it takes for the pump to range from the max. displacement to the neutral position when the inching pedal is instantaneously pressed after fully pressing the travel pedal.
Låg hastighet
Hög hastighet
0=Samma bromskraft vid alla hastigheter. 100=Hårdare broms vid hög hastighet.
SERVICE MANUALpage 47
INTERNALCOMBUSTION
2,5 - 3,0 - 3,5 t
4) ENGINE CUSTOMIZEDAllows setting of the parameters who controls the thermal engine . Do not modify the standard values.
TRAVEL PEDAL INC. (sekunder från tomgång till fullgas)This parameter defines how long time it takes for the actuator to achieve its stroke when the travel pedal is fully pressed (the higher the value of this parameter, the longer the time the thermal engine takes to range from its min. RPM to its max. RPM).
TRAVEL PEDAL DEC. (sekunder från fullgas till tomgång)This is the same as the previous parameter (the time it takes for the thermal engine to range from its min. speed to its max. speed).
MAST INC.This parameter defines the time it takes for the actuator to achieve its stroke when the lifting lever is pulled(higher value of this parameter = longer time for the thermal engine to range from its min. RPM to its max. RPM).
MAST DEC.This parameter is similar to the previous one (time it takes for the engine to range from its max. RPM to its min. RPM when the lifting lever is released).
MAST FIXED CMD 1
MAST FIXED CMD 2Parameter that defines the thermal engine speed rate when one of the auxiliary devices of the hydraulic valve unit is activated (tilt , sideshift, 4th way, 5th way).The engine RPM is increased to a value, according to the parameter set. Standard value is 30 - 40%.
Ex: engine min. speed: 700 rpm; engine max. speed: 2500 rpmusable range: 700 - 2500 = 1800 rpmparameter (mast fixed cmd): 25 %
If the engine operates at a speed higher than 1100 rpm and the hydraulic lever is activated, the actuator will bring the engine rpm to: 1100 + (2500 - 700)x0.25 = 1550 rpm.
Do not increase the speeds set to avoid dangerous manoeuvres.Stroke of the sideshift: 2 -2.5 secsTilting: 4.5 - 5 secs
MAST MAXIMUM CMD (Available from 2001)Parameter which defines the max thermal motor rpm when the lifting is started. By activating the lever, themotor speed increases step by step until the max value set.
SERVICE MANUALpage 48
2,5 - 3,0 - 3,5 tINTERNAL
COMBUSTION
5) FAULT DETECTED
Displays the system faults.
- FAULT OCCURRING NOWPress [ENTER] to display the current fault.
- FAULT SINCE START UPPress [+] and [-] to display the last five faults occurred.
FAULTS MESSAGES SHOW ON THE CONSOLE
“Excitation Sensor” The exitation voltage of the sensor is < 2V or > 5.5V.
“Power Supply” The supply voltage of TCS control unit is < 9.5V or > 32V for more than2 sec. long.
“Travel Pedal Sensor” The signal (voltage) of the travel pedal potentiometer has exceeded thelimits set while calibrating.
“Break/Inching Pedal Sensor” The signal (voltage) of the brake pedal potentiometer has exceeded thelimits set while calibrating.
“Mast Lever Sensor” The signal (voltage) of the mast lever has exceeded the limits set whilecalibrating.
“Actuator Sensor” The signal (voltage) of the feedback potentiometer has exceeded the limitsset while calibrating.
“Error on Actuator control loop” >20% error, for more than 0.5 secs, between the actuator setpoint and thepotentiometer feedback
“Error on pump control loop” >20% error, for more than 0.5 secs, between the pump control signal andthe potentiometer feedback signal in the pump.
“Feed bak error” Pump feed back is < 0.25V or > 4.75V.
“Neutral out of range” During the calibration the pump neutral is out the limits fixed.
“Pump neutral drift too high” The difference between the pump in neutral calibration function and thepump in neutral while the values are not fed is >341 mV
“Feedback moves too fast” The pump feedback changes too fast in comparison with the real change ofthe pump displacement.
“Eeprom error at address” One parameter at least is outside the field of acceptable values.
SERVICE MANUALpage 49
INTERNALCOMBUSTION
2,5 - 3,0 - 3,5 t
“Direction switches error” The TCS control unit takes contemporarily the forward and reverse gear(running mode) started..
“Other Default” Other faults.
6) INFORMATION
Displays the SOFTWARE version
7) PH PARAMETERS
- PASSWORD (4567 or 4321)Enter the password (4 numbers) with the digital key and then valid (enter).Press the key / esc then [+] and [-] in order to haves access to the rest of the menu.
- PUMP NEUTRAL OFFSETThis parameter is made to offset pump feedback
- ENABLE LIMIT CHANGEDuring the calibration of the pedals, the auxilary’s levers and the actuator, it is possible that the minimal values andmaximal values abtained on the potentiometer are not conform to the limit fixed by the programm. It is possible tomodify theses limits.In the menu calibration, authorise the mode calibration. Go into the menu “PH PARAMETERS” and into theunder menu “ENABLE LIMIT CHANGE”.It is necessary to be in “NOT LOCKED”.
- INVERSION BRAKINGThis function is made to have a braking action if direction switch is set in the reverse position during the translationof the machine.The brake action will be proportionnal to the position of the travel pedal.
- INVERSION DESPLACEMENTThis parameter set the inversion time range from: 0 - 10 cc
- DISABLE PUMP DELAYParameter which defines the time of delay of the negative brakes starting up (standard values 30 cycles). It is thedelay for the brakes starting up after the pump has reset its displacement. In order to have the brakes started upin a shortime, for example in ramp, reduce the value (min 5 max 45 cycles)
- REGULATOR OFFSETThis is the acceptable difference between the ordered engine speed and the measured engine speed.If this value is exceeded, the antistall function is active.
SERVICE MANUALpage 50
2,5 - 3,0 - 3,5 tINTERNAL
COMBUSTION
- ANTISTALL COEFCoefficient apply to the action of antistall function.The parameter change from 3 to 8.Bigger is the values more is the desplacement decrease.
- DERIVEE ANTISTALLDefinition of the derived gain for the antistall action. The parameter is a variable number from 10 to 30.Bigger is the number, bigger is the sensibility at the RPM variation on antistall.
- FULL STROKE CMDCompensation of the electric stroke used on the recopy potentiometer of the pump.The parameter is a number (never vary it) 1488
- ENGINE DELAI INCThis parameter is made to take into account the reaction time of the couple actuator/engine in order to activate theantistall at the right moment. It avoids to put the antistall function all the time.
- ENGINE DELAI DECThis value is the complementary value of engine delay dec. It is take into account during the engine deceleration.
8) EPROM RESET
This menu is made to reset the data of the EEPROM
- PASSWORDEnter the password (4 numbers) with the digital key and then valid (enter).Press the key / esc then [+] and [-] in order to haves access to the rest of the menu.
- ALL EEPROM RESETA press on the key (ENT) cancel the list of the statistics.
- FAULT LIST RESETA press on the key (ENT) cancel the list of the detected defaults.
TROUBLES OCCURRING WHILE CALIBRATING
The voltage values read by the transmission potentiometers (pedals, hoisting, etc.) must not exceed the limits set.If there is some wiring failure or the mechanical limit stops of the potentiometers are not properly adjusted, thevoltage they supply will exceed the allowable range for the control unit, thus preventing the calibration procedure.In that case, the terminal will display one of the following messages (while calibrating or in the “fault detected”alarm menu):
travel pedal position out of range travel pedalbrake/inching pedal sensor brake pedalmast lever sensor mast leveractuator position out of range thermal engine actuatorfeed-back error hydrostatic pump potentiometer
SERVICE MANUALpage 51
INTERNALCOMBUSTION
2,5 - 3,0 - 3,5 t
1) TRAVEL PEDAL
travel pedal position out of range (error message)
release the parking brake (the terminal will range fromthe CALIBRATION MODE to theDISPLAY MODE)
select the (the terminal will display theTRAVEL PEDAL submenu voltage - expressed in volts - that
is supplied from the otentiometerin the travel pedal)
yes voltage = 0 volt? no
check the hold down the [ENTER] key andpotentiometer wiring check if voltage changes when
the pedal is pressed
does voltage change?
yes no
press the [ENTER] key to check the potentiometer wiringmeasure the min. and max. voltagesupplied by the potentiometer
adjust the mechanical limit stop ofthe pedal so that the voltage doesnot exceed the ranges set(see “travel calibration”)
Calibrate the travel pedal.
�
�
�
�
�
� �
�
�
SERVICE MANUALpage 52
2,5 - 3,0 - 3,5 tINTERNAL
COMBUSTION
2) BRAKE/INCHING PEDAL
brake/inching position out of range (error message)
release the parking brake (the terminal will range fromthe CALIBRATION MODE to theDISPLAY MODE)
select the BRAKE/ (the terminal will display the voltage inINCHING PEDAL submenu volts, that is supplied by the brake
pedal potentiometer)
yes voltage = 0 volt? no
check the hold down the [ENTER] key and potentiometer wiring check if voltage changes when
the pedal is pressed
does voltage change?
yes no
press the [ENTER] key to check the potentiometer wiringmeasure the min. and max. voltagesupplied by the potentiometer
adjust the mechanical limit stops ofthe pedal so that the voltage doesnot exceed the ranges set(see “travel calibration”)
Calibrate the brake pedal.
� �
�
�
�
�
�
�
�
SERVICE MANUALpage 53
INTERNALCOMBUSTION
2,5 - 3,0 - 3,5 t
3) MAST LEVER
mast lever sensor out of range (error message)
release the parking brake (the terminal will range fromthe CALIBRATION MODE to theDISPLAY MODE)
select the (the terminal will display theMAST LEVER submenu voltage in volts, that is supplied
by the mast lever)
yes voltage = 0 volt ? no
check the potentiometer Hold down the [ENTER] key andwiring check whether voltage changes
when the lever is pulled
does voltage change?
yes no
press [ENTER] to measure the check the electrical connectionsmin. and max. voltage supplied by of the potentiometerthe potentiometer
Adjust the shims of thepotentiometer support bracket sothat the voltage does not exceedthe ranges set (see “mast levercalibration”).If the lever is shiftedforward from its middle position(for the forks lowering) voltage isnot to decrease.
Calibrate the mast lever.
�
�
�
�
�
� �
�
�
SERVICE MANUALpage 54
2,5 - 3,0 - 3,5 tINTERNAL
COMBUSTION
4) THERMAL ENGINE ACTUATOR
actuator position out of range (error message)
release the parking brake (the terminal will switch from theCALIBRATION MODE to the DISPLAYMODE)
select the ENGINE (the terminal will display the voltage, CALIBRATION submenu in volts, supplied by the potentiometer of
of the actuator)
yes voltage = 0 volts? no
check the electrical con- hold down the [ENTER] key and nections of the actuator check if voltage changes while the
actuator rotates
does voltage change?
yes no
press the [ENTER] key to measure check the actuator electrical connectionsthe min. and max. voltage suppliedby the actuator potentiometer
adjust the length of the tie rod sothat voltage does not exceedthe ranges set(see “engine calibration”)
Calibrate the actuator.
� �
�
�
�
�
�
�
�
(engage theparking brake andpress theaccelerator pedal)
SERVICE MANUALpage 55
INTERNALCOMBUSTION
2,5 - 3,0 - 3,5 t
5) POTENTIOMETER IN THE HYDROSTATIC PUMP
feed-back error (error message)
release the parking brake (the terminal will range from theCALIBRATION MODE to theDISPLAY MODE)
select thePUMP NEUTRAL submenu (the terminal will display the
voltage, in volts, that is suppliedby the potentiometer in thehydrostatic pump)
yes voltage = 0 volts or 5 volts ? no
check the potentiometer voltage = 2.48 ̧ 2.52 volts ? electrical connections
yes no
engage the parking brake,switch to CALIBRATION modeand calibrate the pumppotentiometer to zero
�
�
�
�
�
� �
�
- check the potentiometer wiring- lift the truck on the shim blocks,
electrically disconnect the pumpsolenoid valves and start up theengine: if the pump supplies someoil, the trouble is a hydraulic ormechanical type (mechanicalmaladjustment of the pump platepositioning in neutraldisplacement)
- after disconnecting the valves, if thepump supplies some oil, switch offthe engine and hold down the[ENTER] key in order to read thevoltage, until a 2.5 volt value isobtained.
engage the parking brake, switchto CALIBRATION mode andcalibrate the pump potentiometerzero.
SERVICE MANUALpage 56
2,5 - 3,0 - 3,5 tINTERNAL
COMBUSTION
SYSTEM FAULTS AND FAILURES
Any system failure is signalled by the blinking warning light located beside the distributor levers.The blinking intermittence indicates the failure importance.The kind of fault is displayed in the FAULT DETECTED menu (“FAULT OCCURRING NOW”submenu).If the warning light blinks slowly (0.5 Hz) the fault is not very important; the machine is ableto work.
Error message Cause Cure
- the signal (voltage) of the travel pedalpotentiometer has exceeded the limitsset while calibrating
- connector disconnected or wrong wiringtravel pedal sensor
brake/inching pedalsensor
mast lever sensor
actuator sensor
error on actuatorcontrol loop
This message may bedisplayed if theaccelerator is pressed(green light on) whenthe engine is off and thebrake is unlocked
power supply out ofrange
- check the potentiometer wiring- check if the voltage values at the
pedal limit stop do not exceedthe limits preset
- adjust the pedal limit stops- calibrate the pedal again- (see page 51)
- the signal (voltage) of the brake pedalpotentiometer has exceeded the limits setwhile calibrating
- connector disconnected or wrong wiring
- as above (see page 52)
- as above (see page 53)
- as above (see page 54)
- the signal (voltage) of the mast lever hasexceeded the limits set while calibrating
- connector disconnected or wrong wiring
- the signal (voltage) of the feedbackpotentiometer has exceeded the limits setwhile calibrating
- connector disconnected or wrong wiring.
- >20% error, for more than 0.5 secs,between the actuator setpoint and thepotentiometer feedback
- connector disconnected or wrong wiring.
- check the actuator wiring- check theactuator potentiometer
output signal (if you press theaccelerator pedal, the actuatorshall rotate forward and thevoltage - measured in “enginecalibration” when the brake isreleased - shall increase)
- check the supply voltage value- the supply voltage of TCS control unitis not included in the 9.5 - 48 volts range
SERVICE MANUALpage 57
INTERNALCOMBUSTION
2,5 - 3,0 - 3,5 t
excitation voltage
feedback error
neutral out ofrange
error on pumpcontrol loop
If the warning light blinks quickly (1 Hz) the fault is serious; the machine stops.
Error message Cause Cure
- wrong value of the supplyvoltage of the potentiometers andmicroswitches
- check that the voltage is equal to 5 volts± 5%
- wrong signal of the feedbackkpotentiometer in the hydrostaticpump
- check that the feedback potentiometervoltage is equal to 2.5 ± 0.15 voltswhen the pump is in neutraldisplacement mode (see page 55)
- wrong signal of the feedbackpotentiometer in the hydrostaticpump when the latter is inneutral displacement mode
- check the potentiometer calibration(PUMP NEUTRAL)
- check that the feedback potentiometervoltage is equal to 2.5 ± 0.15 voltswhen the pump is in neutral displacementmode (see page 55)
- >20% error, for more than 0.5secs, between the pump controlsignal and the potentiometerfeedback signal in the pump
- check the pump wiring(potentiometer and solenoid valves)
- check that the feedback potentiometervoltage properly changes whilecontrolling the solenoid valves
- measure the min. and max. voltage ofthe pump potentiometer and check thatthe control max. value is kept constantduring the forward and reverse runningmode (when the wheels turn forwards,the potentiometer voltage has to tendto 5 volts) (when the machine is runningin the pump neutral calibration function)
SERVICE MANUALpage 58
2,5 - 3,0 - 3,5 tINTERNAL
COMBUSTION
if the fault warning light is off:- check the signal of the speed sensor
(DISPLAY-ENGINE SPEED menu (check if the valuedisplayed is acceptable)
if the warning light blinks slowly:- check the signal of the travel pedal
(CALIBRATION - TRAVEL PEDAL CALIBRATION menu)if the warning light blinks quickly:- check the supply voltage of the sensors (5 volts)
(CALIBRATION - SENSOR EXCITATION menu)- control unit supply voltage
(CALIBRATION - POWER SUPPLY menu)- signal of the pump potentiometer
(CALIBRATION menu (display mode)-PUMPNEUTRAL)
- wiring of the pump potentiometer(CALIBRATION menu (display mode)-PUMPNEUTRAL )
- wiring of the pump displacement control solenoid valves(VISUAL INSPECTION)
The thermal engine works correctlybut the pump is faulty
The pump works correctly but thethermal engine is faulty
The pump and engine work correctly,but the engine does not acceleratewhen the distributor levers areactuated
The pump and thermal engine do notwork
Fault Possible cure
- check the parking brake operation (DISPLAY-BRAKE SWITCH(set-not set) menu)
- check the operation of the speed selector (pedals with steering-wheel operated reverse gear) or the microswitches on the otherpedals DISPLAY-DIRECTION SWITCH (neutral forwardreverse menu)
- check the signal on the speed sensor (on the pump)(DISPLAY-ENGINE SPEED menu - check if the valuedisplayed is acceptable)
- check the signal of the feedback potentiometer (on thepump)(CALIBRATION menu (display mode)-PUMPNEUTRAL)
- check the actuator operation(CALIBRATION (display mode) - ENGINECALIBRATION menu)
- check the mast potentiometer signal and wiring (of thepotentiometer and microswitches) -(CALIBRATION (display mode)-MASTLEVER CALIBRATION menu)
- check if the potentiometer is fitted (TCS parameter)(CALIBRATION menu, MAST LEVER, mast sensor presence(1) menu)
TROUBLESHOOTING
SERVICE MANUALpage 59
INTERNALCOMBUSTION
2,5 - 3,0 - 3,5 t
WHEELS / TYRES
SAFETY OF WHEELS AND RIMS WHILE USING THE TRUCK“TYRES” are to be replaced when the tyre tread is under 1.6 mm.“SUPERELASTIC” tyres are to be replaced when the tyre tread reaches the“60 J” mark, which is printed on the tyre side.
WHEEL TIGHTENING TORQUEDriving wheels 17 daNmSteering wheels 24 daNm
SUPERELASTIC (SE)
PNEUMATIC (PN)
T YRE T YPE SIZEAIR
PRESSIO NT YPE
SUPERELAST IC( SE)
F RO NT7 . 0 0 - 1 2
2 7 X1 0 - 1 22 . 5
3 . 0 - 3 . 5
REAR 6 . 5 0 - 1 02 . 5 - 3 . 0 - 3 . -
5
PNEUM AT IC( PN)
F RO NT
7 . 0 0 - 1 22 7 X1 0 - 1 2 ( 1 6
PR)2 7 X1 0 - 1 2 ( 2 0
PR)
9 b a r8 b a r
1 0 b a r
2 . 53 . 0 - 3 . 5
REAR 6 . 5 0 - 1 0 7 , 7 5 b a r2 . 5 - 3 . 0 - 3 . -
5
T W INSUPERELAST IC
( SEG )F RO NT 7 . 0 0 - 1 2
2 . 53 . 0 - 3 . 5
T W INPNEUM AT IC
( PNG )REAR 7 . 0 0 - 1 2 9 b a r
2 . 53 . 0 - 3 . 5
SERVICE MANUALpage 60
2,5 - 3,0 - 3,5 tINTERNAL
COMBUSTION
CHECKING THE SYSTEM SEALING AND CLEANINGTHE POWER STEERING SYSTEMEvery 250 hours - Check the whole system for any possible leakage; before servicing,
release the system pressure.Every 4,000 working hours- replace hoses (D) connecting Orbitrol to the steering cylinder.Every 10,000 working hours- replace the system pipes.
Adjusting the power steering pressureThe max. pressure of the power steering is to be equal to 100 Bar
POWER STEERINGCIRCUIT DRAWING
A
D
B
PRIORITY VALVE(C)
D
STEERING CONTROL
The steering uses the same oil as the lifting by means a priority valve, so that a sufficientoil flow to the power steering is always assured.The oil capacity is checked by the Ls signal (load - sersing) coming from the steeringunit and it occurrs so that the oil capacity sent to the power steering is equal to itsactual request.The exceeding oil is sent to the control valve for other functions.When the steering wheel is turned the steering unit “measures” a volume of oil proportionalto the above rotation and sends it into the steering cylinder.
Do the following to adjust the power steering pressure:1 - Install a pressure gauge in (C) the power steering;2 - With a socket head spanner, remove the cap located in the Orbitrol upper part to reach the
adjusting screw (B) (power steering unit);- screw in to increase pressure- screw out decrease pressure
SERVICE MANUALpage 61
INTERNALCOMBUSTION
2,5 - 3,0 - 3,5 t
STEERING AXLE
Every 500 hours- lubricate the steering gear joints using the appropriate grease nipples (C);- check the steering angles.
Every 2.000 hours- check and if it is necessary, adjust the wheel hub bearings.
Every 500 ore check the angles
Max steering angle (internal wheel ≅ 75°)
If any abnormal consumption of the wheel tread is observed, the following controlsshould be made:- check the parallelism of the steered wheels;- check that the steering angle of the wheels is the same in both directions.
B = 75° STANDARD VALUE80° MAX VALUE WITH PN85° MAX VALUE WITH SE
ANGLE MEASURED BY THE AXLE FRAME TO THE INTERNALWHEEL THROUGH A SPECIAL DEVICE
END STROKESETTING SCREW
STEERING AXLE
G
C
CC
C
SERVICE MANUALpage 62
2,5 - 3,0 - 3,5 tINTERNAL
COMBUSTION
BEARING ADJUSTMENT
Steering wheel bearings require an adjustment once a year.
Steering wheels- lift the steering wheels- remove cap (1);- remove toothed washer(4);- fasten the nut with a torque setting of 6 dNm;- turn the hub of 2-3 turns in both senses;- unfasten nut (3) and retighten with a 2-1 daNm torque;- check that the wheels slide correctly (max. rolling final torque: 0.2 dNm)
and that there is no side play (maximum axial play of 0.05 mm);- reassemble the toothed washer;- reassemble the cap (1);- lower the wheels again and check that all nuts fixing the rim are well tightened.
1
2
4
5
3
SERVICE MANUALpage 63
INTERNALCOMBUSTION
2,5 - 3,0 - 3,5 t
HYDRAULIC DISTRIBUTOR
Nominal capacity 80 l/min3 - 4 - 5 section
Lifting potentiometer
Max lifting pression 235 ± 5 Bar
Relief valve pressionTilting 180 BarSide shift 150 Bar
Microswitch
Nipple 1/2 Gas
Restrictor Ø 2 mm
SERVICE MANUALpage 64
2,5 - 3,0 - 3,5 tINTERNAL
COMBUSTION
MAST GROUPS
The mast profile - CESAB design - with double stiffening flange is characterised by a highflexural and torsional strength.It allows wide visibility thanks to the reduced dimensions of the profile itself.Cylinders are single-acting type.The sideshift system has been housed inside the profiles.The mast group is a roller type with a variable centre distance (i.e. a fixed roller is fitted on theouter mast and a mobile one on the inner mast, instead of a number of mobile rollers only onthe inner mast). This solution ensures better grip and stability on operation.
Other features: side plays adjustable from outside. Plastic guide shoes. Roller bearings withgrease nipples, ball joints on axle couplings and tilt cylinders.
Lifting cylinders:Duplex mast: VT 2 side cylinders
FFL 2 central cylinders1 central cylinders for the FFL
Triplex mast VT 2 side cylindersFFL 2 side cylinders
1 central cylinders for the FFL
Grease nipple Adjusting screw Shoe Roller
SERVICE MANUALpage 65
INTERNALCOMBUSTION
2,5 - 3,0 - 3,5 t
TRIPLE MAST SECTION
Fork carriage
Internalsection bar
Intermediatesection bar
Externalsection bar
SERVICE MANUALpage 66
2,5 - 3,0 - 3,5 tINTERNAL
COMBUSTION
6
4
5
3
1
2
5
DIAMETRODISPINTA
7
Fig. A Fig. B
In these cylinders a seal (1) has been fitted on thepiston (2) that works on the inner surface of thecylinder liner (3).
The rod guide is made by the plug (4) and by thepiston through anti-friction rings (5).
The dust control ring (6) prevents any dirt and waterfrom penetrating the cylinder.
Slight leakages that may occur are directed to thetank through the drain pipe connected to the pipecoupling (7).
The drain pipe shall reach the oil tank (fig. B)
A small quantity of oil will always remain in the loopformed by the pipe before connecting to the tank. Itacts as a trap and constantly moisturizes the cylinderliner, when it is completely closed (fig. B).
DESCRIPTION OF THE CYLINDER COMPONENTSThe cylinder pistons are single-acting types (fig. A).
SERVICE MANUALpage 67
INTERNALCOMBUSTION
2,5 - 3,0 - 3,5 t
Fig. C
CYLINDER CHECKING METHODS
1ST CHECKRemove the drain pipe from the cylinder (fig. C)
Lift the cylinder some times to end stroke, so as todischarge any oil residual.
Put a load on the forks and lift it by at least 200 mm.
After 10 minutes, measure the amount by which theload has lowered. A drop of a few millimetres is quitenormal, as in the distributor there are always someleakages.Now, lift the cylinder to its end stroke, if no oil leaksfrom the drain pipe coupling, it means that the loadlowering is only due to the leakages on the distributor.
In the presence of leakages, it will be necessary toreplace the seal. Should this be the case, inspect thecylinder liner.
2nd CHECK(To be carried out if the 1st inspection has beensuccessful and after seal replacement).
Remove the drain pipe from the cylinder.
Lift the cylinder some times to end stroke, so that allthe possible remaining oil is discharged.
Put a load on the forks. Lift and lower it for 10 minutes,making sure that the limit stop is never reached.
Lift the cylinder to end stroke.
If any leakages should be still present, the cylinder isdamaged and then it must be replaced.
SERVICE MANUALpage 68
2,5 - 3,0 - 3,5 tINTERNAL
COMBUSTION
LUBRICATION
Masts
After the first 50 hours- adjust the guide shoes through socket head screw (D).
Use a 0.2 - 0.5 mm thickness gauge; fit it from the bottom upwardsto socket head screw (D) centre, passing behind roller (E) andcreeping on the outer mast.
Every 50-100 hours- Grease the mast sliding guides- through the grease nipples, lubricate the articulations of the tilt cylinders
and of frame coupling.
Every 250 hours- adjust the guide shoes;- grease mast guide rollers (E).
Every 2000 hours- inspect mast guide rollers (E); they have to rotate freely and not
to be too worn out.
A) tilt cylinders2+2 grease nipples
B) mast coupling1+1 grease nipples
Fork mounting carriage and sideshift
After the first 50 hours- adjust the guide shoes through socket hallen screw (D).
Use a 0.2 - 0.5 mm thickness gauge, fit it from the bottom upwardsup to socket hallen screw (D), going behind roller (E).
Every 50 hours- lubricate the sideshift guides through the grease nipples.
Every 250 hours- grease the pins and the fork positioning slots;- adjust the guide shoes;- grease the guide rollers of carriage (F).
D
E
B
D
F
E
A
SERVICE MANUALpage 69
INTERNALCOMBUSTION
2,5 - 3,0 - 3,5 t
Every 2,000 hours- check the conditions of the guide rollers; they
have to rotate freely and not to be too wornout.
C) Sideshift(upper part) 2 grease nipples(lower part) no grease nipple
INSTALLATION CHECKSSAFETY SPECIFICATIONS
Make sure that:- the hoisting chain stretchers are not faulty and
the adjusting nuts are locked by counternuts andcheck pins (F);
- safety limit stops (A) of the fork mounting carriageare fitted and tightened up;
- stop collars (D) are fitted and tightened up;
Every 500 hours- check that distance (D) between the collar and
the mast outer cylinder ranges from 0.5 mm to3 mm;
- check if self-locking nuts (B) are tightened up.
Tightening torques- Nuts of the stop collars: 0.8 to 1.2 daNm
SAFETY LIMIT STOPS OF THE FORKMOUNTING CARRIAGESThe mast unit is equipped with a mechanical safetylimit stop to prevent the accidental removal of thefork mounting carriage from the mast downwards.Limit stops (A) consist of two socket head screwswith counternut. Loosen limit stops (A) beforedisassembling the fork mounting carriage.
C
D
B
D
A
F
SERVICE MANUALpage 70
2,5 - 3,0 - 3,5 tINTERNAL
COMBUSTION
CHAIN INSPECTION
Every 500 hours (anyway, chains are to be checked every 3 months)- chains are not to be faulty or worn out.
To check if the chain links are worn out, use the appropriate ruler; remember thatchains must be replaced when, in a portion corresponding to 34 pitches, only33 pitches are found.
Every 1,000 hours- disassemble the chains, carefully clean them, reassemble reversing their original
work position, and grease.Every 10,000 hours
- replace the chains and the fastening tie rods.
Use of original CESAB chains will guarantee that the safety requirementsstated by the regulations in force are complied with.
G
F
D D
F
EE
G
FORK INSPECTION(to be performed every 1000 hours)
- Surface cracks particularly in D/E/F- Height difference of the tips (is to be < 3% than the fork
length)- Positioning latch (G)- Punching is to be clear- Fork measure (maximum wear = 10% of the original thickness)
particularly in point D- Wear of the fork fastening devices on the carriage (E-
F)
X = 152 mm (2,5T)203 mm (3,0 - 3,5T)
TABLE ISO 2328 - 1993
Rate lifting load (kg) "X" (– 5)
I B 0 999 114 mm
II B 1 000 2 500 152 mm
III B 2 501 4 999 203 mm
IV B 5 000 8 000 254 mm
V B 8 001 10 999 257 mm
SERVICE MANUALpage 71
INTERNALCOMBUSTION
2,5 - 3,0 - 3,5 t
LIFTING OF THE FORKLIFT TRUCKWITH CABIN
A- CHAINS: dia. 13 mm - Degree T (8) - UNI9425
B- HOOKS: for 5.4 t - UNI/ISO 7597
C- N° 2 upper brackets to hold the chains.
HOOKS ATTACHMENT POINTS FORLIFTING THE TRUCK
To lift the truck the following equipment must beused:
A- CHAINS: dia. 13 mm - Degree T (8) - UNI9425
B- HOOKS: for 5.4 t - UNI/ISO 7597
AA
B
C C
A
B
LIFTING OF THE TRUCK
TRUCK WEIGHTON THE AXLE WITH OUT
LOAD(FRONT / REAR)
2.5 t 4050 kg 2070 / 1980 kg
3.0 t 4600 kg 2100 / 2500 kg
3.5 t 5160 kg 2260 / 2900 kg
SERVICE MANUALpage 72
2,5 - 3,0 - 3,5 tINTERNAL
COMBUSTION
OIL AND GREASE SPECIFICATIONS
TYRE PRESSURES TIGHTENING TORQUES
FOR NORMAL ENVIRONMENTS
USED TYPE SPECIFICATIONS QTY.PARTS INVOLVED
AGIP ARNICA 46 ISO - L - HVFZG tests to stage 11
39 LHydraulic system, lifting, power steering andhydrostatic transmission
MOBIL ANTICONGELANTE - - Cooling liquid
MOBIL DELVAC 1300SUPER SAE 15W-40
API CD-SF CCMC-D3(SHPDO)-PD1 MIL-L-2104D
MIL-L-46152B- DIESEL engine
20 ÷ 40 SAE - - Mast chain lubrication
MOBILGREASE SPECIALLithium base
ASTM 275 305 NLGI N.2dropping point 180
-Mast securing joints - sideshift unit - steeringjoint - general lubrication with grease nipples
FOR COLD CLIMATES AND COLD-STORAGE CELLS
PARTS INVOLVED
AGIP ARNICA 22 ISO - L - HVFZG tests to stage 10
39 LHydraulic system, lifting and power steeringunits
MOBILTEMP SHC 100Thickening Infusible
ASTM 265 295 NLGI N.2Dropping point >260
-Mast securing joints - sideshift unit - steeringjoint - general lubrication with grease nipples -mast guides
TYRE PRESSURES
9,5 bar7,5 bar
400-450500
FRONT tyres
9,25bar
REAR tyres
WHEEL TORQUE
37 daNm steered wheels
50 daNm driven wheels
DRIVE UNIT TORQUE
27 daNm engine fixing to chassis
VARIOUS TORQUES
40 daNm bolts securing mast
0,8 1,2 daNm jack collar self-locking nuts
77 daNm counterweight blocking screws
SERVICE MANUALpage 73
INTERNALCOMBUSTION
2,5 - 3,0 - 3,5 t
RUNNING IN MAINTENANCE
The servicing periods are divided into hours, consideringan average working day of 8 hours of effective operation.If the truck is used on average for less than 8 hours perday, refer to the schedules expressed in days/months
LEGEND
In the maintenance table showing a visualcontrol and cleaning of the parts indicated.
In the maintenance table showing thereplacement of the parts indicated.
In the maintenance table showing lubrificationof the parts indicated.
In the maintenance table showing tighteningor adjustment of the parts indicated.
50 500 #at # hours for MEDIUM/INTENSEUSE
7/- -/3 #at # days/months FOROCCASIONAL USE
ENGINES
engine oil and cartridge
clearances engine values
fan belt and alternator belt
CHASSIS AND CONTROLS
general bolt and nuts
wheel torque (1)
(1) During the first 500 worning hours, checkthe torque every 50 hours
LIFTING UNIT - MASTS
mast guide pads
oil filter
HYDROSTATIC TRANSMISSION
transmission oil filter
transmission oil
SERVICE MANUALpage 74
2,5 - 3,0 - 3,5 tINTERNAL
COMBUSTION
MAINTENANCE TIMES
8 50 250 500 1 0002
0004
00010
000 #at # hours for MEDIUM/INTENSEUSE
1/- 7/- -/1 -/3 -/6 -/12 -/24 -/60 #at # days/monthsFOR OCCASIONAL USE
mast guide pads
carriage - sideshift unit slides
mast rollers and chain rollers
tilting jacks supply tubes
fork positioning pins
mast guides, mast and jack fixing
lifting jack collars
fork carriage position
forks
mast tilting
mast secured to chassis
lifting chains
chain securing bolts
high pressure hydraulic hoses
system seal and connections
SERVICE MANUALpage 75
INTERNALCOMBUSTION
2,5 - 3,0 - 3,5 t
MAINTENANCE TIMES
8 50 250 500 1000 2000 4000 10 000 #afteri # hours FORMEDIUM/INTENSE USE
1/- 7/- -/1 -/3 -/6 -/12 -/24 -/60 #after # days/months FOROCCASIONAL USE
CHASSIS AND COMMANDS
chassis - cleaning
bolts in general
fuel tank cleaning
fuel tank control
driver’s seat
wheels - hub bearings
tyre inspection and wheel tightness
tyre pressures
steering system and tubing seal
hoses from orbitrol to steering jack
rear axle and weheel hub bearings
steering lock
pedals in general - linkage
brake commands solenoid valve
SERVICE MANUALpage 76
2,5 - 3,0 - 3,5 tINTERNAL
COMBUSTION
MAINTENANCE TIMES
8 50 250 500 1 000 2 000 4 00010000
#at # hours for MEDIUM/INTENSEUSE
1/- 7/- -/1 -/3 -/6 -/12 -/24 -/60 #at # days/months FOR OCCASIONUSEENGINE
cooling liquid
fuel filter cartridge
air filter
dusty environment air filter
cyclone prefilter
water and oil radiator (external cleaning)
water and oil radiator in dustyenvironments
fan belt and alternator belt
engine oil and filter cartridge
engine supports
engine linkage and fuel connections
fexible fuel and water hosing
DIESEL engine injection pressure control
DIESEL engine valve clearance
PETROL and LPG engine valveclearance
PETROL and LPG engine spark plugs
LPG system control
LPG bottle hose and safety valve
LPG pressure reducer
SERVICE MANUALpage 77
INTERNALCOMBUSTION
2,5 - 3,0 - 3,5 t
MAINTENANCE TIMES
8 50 250 500 1000 2000 4000 10000 #at # hours for MEDIUM/INTENSEUSE
1/- 7/- -/1 -/3 -/6 -/12 -/24 -/60 #ati # days/months forOCCASIONAL USE
ELECTRIC SYSTEM
pushbuttons - pedal microswitches
cable terminals - cable sheaths
battery electrolyte level and density -replacement
battery terminals and poles
HYDROSTATIC TRANSMISSION
system seal
transmissin oil filter
transmissin oil
complete unit
Var 2000:e timme tillkommer:0:0 Grupp 0 Hel maskin0:14 Ram, kontroll av sprickor
1:0 Grupp 1 Motorer1:15 Kylvätska, byte
4:0 Grupp 4 Styrning4:4 Slangar, kontroll
4:5 Styrtryck, kontroll
5:0 Grupp 5 Elsystem5:13 Laddning, kontroll
6:0 Grupp 6 Hydraulik6:5 Hydraultryck, kontroll
6:6 Hydraulolja, byte
6:7 Returfi lter, byte
6:8 Sugfi lter, rengöring/byte
7:0 Grupp 7 Arbetsfunktion7:6 Gaffl ar, gaffeltest
Var 1000:e timme tillkommer:0:0 Grupp 0 Hel maskin0:13 Bränsletank, rengöring
1:0 Grupp 1 Motor1:13 Remmar, byte
1:14 Ventilspel, kontroll
2:0 Grupp 2 Hydrostatik2:3 Bultar, kontroll/fastsättning
3:0 Grupp 3 Bromsar/hjul3:7 Hjullager infettning
5:0 Grupp 5 Elsystem5:12 Kablage/anslutningar
6:0 Grupp 6 Hydraulik6:4 Andningsfi lter, reng./byte
BT Cargo CBD 2.5-3.5Var 250:e timme
Pos Kontroll av:
0:0 Grupp 0 Hel maskin0:1 Dörrar/luckor
0:2 Motviktsinfästning
0:3 Förarskydd/hytt
0:4 Skyltar/dekaler
0:5 Förarmiljö
0:6 Stol/mattor
0:7 Pedalgummin
0:8 Torkare/spolare
0:9 Provkörning test av
samtliga funktioner
0:10 Smörjning enligt schema
0:11 Tvätt/rengöring
1:0 Grupp 1 Motor1:1 Missljud/läckage
1:2 Gaspedal/reglage
1:3 Luftfi lter, kontroll
1:4 Kylvätska, nivå/fryspunkt
1:5 Remmar, kontroll
1:6 Motorolja, byte
1:7 Motoroljefi lter, byte
1:8 Bränslesystem, läckage
1:9 Glödning
Pos Kontroll av:
2:0 Grupp 2 Hydrostatik2:1 Läckage
2:2 Funktion
3:0 Grupp 3 Bromsar/hjul3:1 Däck/hjul
3:2 Lufttryck däck
3:3 Hjulbultar/hjullager
3:4 Färdbroms, funktion/läckage
3:5 Parkeringsbroms, funktion
3:6 Pedallänkage
4:0 Grupp 4 Styrning4:1 Styrleder/Styrspindlar
4:2 Styrcylinder, fastsättning
4:3 Styrlagring/upphängning
5:0 Grupp 5 Elsystem5:1 Belysning/körriktningsvisare
5:2 Instrument/kontrollampor
5:3 Signalhorn
5:4 P-broms-/Backalarm
5:5 Timmätare, avläsning
Pos Kontroll av:
5:6 Batteri, fastsättning
5:7 Säkringar
5:8 Batterivätskenivå
6:0 Grupp 6 Hydraulik6:1 Slangar/rör
6:2 Ventilreglage/länkage
6:3 Oljenivå
7:0 Grupp 7 Arbetsfunktion7:1 Lyftstativ, infästning
7:2 Gaffl ar
7:3 Lyftkedjor
7:4 Laststöd
7:5 Lyft-/tiltcylindrar
Var 500:e timme tillkommer:0:0 Grupp 0 Hel maskin0:12 Bultar/Muttrar, fastsättning
1:0 Grupp 1 Motorer1:10 Bränslefi lter, byte
1:11 Luftfi lter, byte
1:12 Motorfästen
5:0 Grupp 5 Elsystem5:9 Batteripoler reng./infettning
5:10 Färdväljare/länkage
5:11 Microbrytare
Totaldokument
Var 2000:e timme tillkommer:0:0 Grupp 0 Hel maskin0:13 Ram, kontroll av sprickor
1:0 Grupp 1 Motorer1:17 Kylvätska, byte
4:0 Grupp 4 Styrning4:4 Slangar, kontroll
4:5 Styrtryck, kontroll
5:0 Grupp 5 Elsystem5:13 Laddning, kontroll
6:0 Grupp 6 Hydraulik6:5 Hydraultryck, kontroll
6:6 Hydraulolja, byte
6:7 Returfi lter, byte
6:8 Sugfi lter, rengöring/byte
7:0 Grupp 7 Arbetsfunktion7:6 Gaffl ar, gaffeltest
Var 1000:e timme tillkommer:1:0 Grupp 1 Motor1:14 Remmar, byte
1:15 Tändinställning
1:16 Tändstift, byte
2:0 Grupp 2 Hydrostatik2:3 Bultar, kontroll/fastsättning
3:0 Grupp 3 Bromsar/hjul3:7 Hjullager infettning
5:0 Grupp 5 Elsystem5:12 Kablage/anslutningar
6:0 Grupp 6 Hydraulik6:4 Andningsfi lter, reng./byte
Var 500:e timme tillkommer:0:0 Grupp 0 Hel maskin0:12 Bultar/Muttrar, fastsättning
1:0 Grupp 1 Motorer1:11 Luftfi lter, byte
1:12 Motorfästen
1:13 Ventilspel, kontroll
5:0 Grupp 5 Elsystem5:9 Batteripoler reng./infettning
5:10 Färdväljare/länkage
5:11 Microbrytare
BT Cargo CBG 2.5-3.5Var 250:e timme
Pos Kontroll av:
0:0 Grupp 0 Hel maskin0:1 Dörrar/luckor
0:2 Motviktsinfästning
0:3 Förarskydd/hytt
0:4 Skyltar/dekaler
0:5 Förarmiljö
0:6 Stol/mattor
0:7 Pedalgummin
0:8 Torkare/spolare
0:9 Provkörning test av
samtliga funktioner
0:10 Smörjning enligt schema
0:11 Tvätt/rengöring
1:0 Grupp 1 Motor1:1 Missljud/läckage
1:2 Gaspedal/reglage
1:3 Luftfi lter, kontroll
1:4 Kylvätska, nivå/fryspunkt
1:5 Remmar, kontroll
1:6 Motorolja, byte
1:7 Motoroljefi lter, byte
1:8 Gasolsystem, funktion
Pos Kontroll av:
1:9 Gasolsystem, läckage
1:10 Tändsystem, kondition
2:0 Grupp 2 Hydrostatik2:1 Läckage
2:2 Funktion
3:0 Grupp 3 Bromsar/hjul3:1 Däck/hjul
3:2 Lufttryck däck
3:3 Hjulbultar/hjullager
3:4 Färdbroms, funktion/läckage
3:5 Parkeringsbroms, funktion
3:6 Pedallänkage
4:0 Grupp 4 Styrning4:1 Styrleder/Styrspindlar
4:2 Styrcylinder, fastsättning
4:3 Styrlagring/upphängning
5:0 Grupp 5 Elsystem5:1 Belysning/körriktningsvisare
Pos Kontroll av:
5:2 Instrument/kontrollampor
5:3 Signalhorn
5:4 P-broms-/Backalarm
5:5 Timmätare, avläsning
5:6 Batteri, fastsättning
5:7 Säkringar
5:8 Batterivätskenivå
6:0 Grupp 6 Hydraulik6:1 Slangar/rör
6:2 Ventilreglage/länkage
6:3 Oljenivå
7:0 Grupp 7 Arbetsfunktion7:1 Lyftstativ, infästning
7:2 Gaffl ar
7:3 Lyftkedjor
7:4 Laststöd
7:5 Lyft-/tiltcylindrar
Totaldokument
Issue 11/2000
CESAB S.p.Avia Persicetana Vecchia, 10 40132 Bologna - Italy
Tel. (0039) 051.20 54 11Fax (0039) 051.72 80 07E-mail: cesab@cesab.it
GB
Cargo Range
Code 036 2005-1
CONSOLE MAP
����������������������������� ���������������
��������������������� ���������������������������
�������������������������
������������������������� ������
������������������������� ���������
�������������������� ����������
�����������
�����
�
��������������������������
���������������������������� ����������� �����
�� ��������� ������������ ��������� ���������� �����
�� ��������� � � ����������� ���� ��������������
�������������������������� �������� ������ �����
�� �� ������ ������������
����������������������������!������
�
�
��
PRESSENTER
��� !"#�# �
press+
�
���
press - press+
������� �$�� ����� ������� �%���$� � ������&
press+
���������'� ������$�� ������� ����� ����������� �����
� ���� �� ��������� � ���$��������������� � � ��
���������� ������ ����������
����������������� �����������������������������������
������������������ �����������������������
�
CalibrationTravel PedalIf Forward switchselect it ('ENT')
CalibrationTravel PedalPush slowly travelpedal
CalibrationTravel PedalFull depression inForward (press a key)
CalibrationTravel PedalDon't touch thetravel pedal ('ENT')
CalibrationTravel PedalIf Reverse switchselect it ('ENT')
CalibrationTravel PedalPush slowly travelpedal
CalibrationTravel PedalFull depression inReverse (press a key)
CalibrationTravel PedalReverse completed(ENT)
CalibrationTravel PedalCompleted
ENTER
�
CalibrationTravel PedalReverse completed(press a key)
ENTER
CalibrationTravel PedalForward completed(ENT)
CalibrationTravel PedalForward completed(press a key)
ENTER
%��$���� ������ �� '� �����������
�������� �$�� ���%����%���$� (� �'� ���� $� ��������� � ������ )������ �����
CalibrationTravel PedalDon't touch tehtravel pedal ('ENT')
� ���� ��*������� � ���$�� ���%���� �������� ��������
���������'� � ������$�� ������� ����������� ��� �������������
���! � +���#������� �$�� ���%���������� �����
,!��� +���#������� �$�� ������������� �����
%��$���� ������ �� '� �����������
�������� �$�� ��������%���$� (� �'� ���� $� ��������� � ������ )������ �����
,!��� +���#������� �$�� ������������� �����
���! � +���#������� �$�� ���%���������� �����
� ����� ��������� � ���$�� ������������� ���������'� � �����
�$�� ������� ����������� ��� �������������
����������������� �!"#��$�%�����&���&&��#������!%�����&��&��&�'!#(�
����������"� ������"� � � �� ��� ���#$��%��&�'�
����������"� �������� ����������� �����
�� ��������� � ��� �$������ �� ���� ��������������
������-����������"� ������ �������� ������ �����
����� �$�� ����� �� ������ ���$�� � �� �������� ����� ���������� �����
����������"� ������
��
����������"� ��������!������
����������$�������������
�
��*������� � ��� � �$� ������� ����������� �� �����
������������!����������!������
�
��
���������
�����&
�����&
���������
���������
���������
���������
���������
�� �� ������ ������������
� ���� �� ��������� � ��� �$������ �� ���� ���������� � � � �
(�)*+�+�+&��&�$�(��+$,&*�+�(�$�&�,�+"$-+�.�.$$�/+�$&�
� ���� ��*������� � ���$�� � ������� ����������� �� � �
�$� � �$�� � �� �������� ������������� �'������
�������������������������� �� ����������
��*������� � ��� �$��� �� � �� ��.���/� ���� �$�� �� ��� �����
� ���� ��*������� ��� �$�� �� �� � ���.�� ��/� � ��� �$�� �� ��� �����
������������!�������
���������
CalibrationMax. forward speed
�
�CalibrationMax. reverse speed
�
�CalibrationMini engine speed
�CalibrationMaxi engine speed
CalibrationParking brake set
�CalibrationPump pot. inverted
�����&
�����&
�����&
�����&
�����&
�����&
����������$�������������
�
����������$�������������������000�1!� ��� �
$�������������$��2��������������
�
$����������������3� ����� ����������000000
$�������������.���� ����� ����������000000000
����������������������������� ���������������
��������������������� ������������
����������
�����
����������
������ �� �
������ ���������� �������� ���� ������������ ������ ������� � ����������!� �"��
�������� ���� ����� � ������� ��#
�������� ���� �"��� ������!�������$"������ %�� ���� ���!� &���� '!!(
�������� ���� � ������� ��#��$"������ %�� ���� ���!� &���
�������� ���� ����"�� ��� ����"�!����� '���%��� � ����%��(
�������� ���� ����"�� ��� � ���� ������)�%��*��� � '���%��� � ����%��(
�������� ���� ����"�� ��� ���� ���*���%��*���+��!�� � '���� ����� ���(
�������� ���� ������� ��#+���� ���� �������� � ��)��� �"����
�������� ���� ����� �"��� ������!�����'!!(� %�� ���� �������������
�������� ���� ����"�� ��� ���� ����!����� �+��!���'��"����� � ���+���� � %�!*+���(
�������� ���� ����"�� ��� � ���� !������� )��)�� �+��!���,-������� ���������� '���� � ���� ���(
�������� ���� !�������� ���)���� ������ � �"�!��������"�� +���� ���� �������� �!��)����� '���� � ���� ���(
�������� ���� ������� ��� ���� �������!�"����� ��� .���
���������������������� ���� �!�����"��#�������#� ��������#�� ��
�������� ���� ���������
�����/
�������� ���� ���������� ��� ���� �"��� �������������������� ����� ���� ��������!� )��"�� '��� �.(
���������
DisplayConstant speed
DisplayActuator feedback
ENTER
ESC
ENTER
ESC
DisplayMast switch
ENTER
ESC
DisplayEngine speed
DisplayAntistall
DisplayPump displacement
DisplayEngine command
DisplayParking brake
DisplayBrake switch
DisplayMast engine Cmd
DisplayPump feed-back
DisplayDirection switch
press+
ENTER
ESC
ENTER
ESC
ENTER
ESC
ENTER
ESC
ENTER
ESC
ENTER
ESC
ENTER
ESC
ENTER
ESC
ENTER
ESC
DisplayPower supply
ENTER
ESC
DisplaySensor exitation
DisplayNeutral drift
ENTER
ESC
ENTER
ESC
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�������� ���� � �������� ��� ���� "�������!� '���%��� � ����%��(
�������� ���� ������� �������� �"������� %�� ���� "�������!
press+
press+
press+
press+
press+
press+
press+
press+
press+
press+
press+
press+
press+
�������������������������
����������n ���������������������
�
�
��
������������������ �����������������������
����������
������ �� �
����� ������������������������� ������
�� ����
������ �������
������ ��������
������ ���������������������
������ ����������������������
press+
������ ��������� �����
������ ��������� ����
������ ��������� � �!�����"
������
��
������ ��������� � �!�����"#$������
���� ���� ���������� ������������ ��� ���� ���� !�� ���"��!#��� ��$!���� #������������#� %&������'�()( $#��� ��*&
������� ���������� ��*&�#+��� �����,
��� ������ ��������� � �!�����"#$������
press+
������
������ ��������� � �!�����% �
�
������ ��������� � �!�����%#$������
��� ������ ��������� � �!�����%#$������
���
������
�
�
�������
�������
�������
�#�� � $#��-���
�#�� � $#��-���
�#�� � $#��-���
�#�� � $#��-���
������ �����&&������� �������
������ %������
������������������������� &��������
���
���� �� � ���� ���"����+�� �������������
������� ��*+���� ������������&
���� ���� ���������� ������������ ��� ���� ���� !�� ���"��!#��� ��$!���� #������������#� %&������'�()( $#��� ��*&
������� ���������� ��*&�#+��� �����,
������� ��*+���� �������-������&
�����
��
���
�������� ����� ��������
���������
����������������������������� ���������������
��������������������� ������������
������� ����� ����� ������
����������
�������
�� �����������
������
���������������
�������
� ����������
�������������� �
������������������������������
�
�����������������������������������������
������ ��� �������� ���������� ��� � ����� �� �
��������������������������������������� �����
�
��
��
��� ���� �
�
������������������������������� �
������������������������������� �����������������
������ � ��� �������� ���������� � ���� �� !������"! �#� $"
���� � �������
������������
�
�
�
������������������������������� �������������������
��������� ����� ������� �
������������������������������� ��������������
������
��
������
������
������
������ �������� �������� ���� ������
����������������������������� ���������������
��������������������� ������������
���������
���������
����������
�����������
�����
���������������
���������������
�������������
���������
�������������
������������
�� ����
�����������������������������������������������������������������������������������������������������
����� ����������������������������������!�"�������������������������������#�������������������
$ ������������������
����������������������������������������
$%�&'(!��������
)����������������($$'%!
�� ��������� ��� � ��� �� � ����� � ��
)����������������($$'%!
�� ����
�� ����
�� ����
�� ����
�� ����
�� ����
��������������������������������
���������
����������������������������� ���������������
��������������������� ���������������������������
������������ ������������ ��������� �������
������������ ��������� ��������������� �
�
������ ��������� �� ���
�� �� ��������� ��������� ������� ������ ������ ���������� �������� ��� ��������� �� �� �� ������� � �������� �������� �����!��� �����
���!��� �������� ���������� �����"
������������ ��������� ��������������� �
�
�#$
������������ ��������� �������
������
�
������������ ��������� ��������������� �
�
�� �� ��������� ��������� ������� ������ ������ ���������� �������� ��� ��������� �� �� �� ������� � � ������� ������ ��!��� �����
��% ��� ������ ������� �����"
������������ ��������� ��������������� �
�#$
�
������������ ��������
������������ ��������� �������
������������ ��������� �������
��
������
������
������
�
�#$
����� �������� ��� ���� ����
����� �������� ��� ���� ������������"
������ ������� �� �����
�����������������������
�������n ����������������� ��
�
�
��
������������������ �����������������������
&�##����
'(#&)*+$,�#,)�
���� ������������������������� �
������
�������
�������
������������
������ �������
�����������������������!���� �
�#$
����� � � ��� ��������!� ��������������
����
��
�#$
���������
������������
������������
����������������������������� ���������������
��������������������� ������������
PARAMETER
CBG 2.5-3.0-3.5CONTINENTAL ENGINE
SETTING VALUE
&$/,%5$7,21�6(&7,21 $&&(77$%/(�9$/8( 67$1'$5'�9$/8(
MAST PRESENCE YES/NO YESMAX FORWARD SPEED 10% - 100% 100%MAX REVERSE SPEED 10% - 100% 100%MIN ENGINE SPEED 850MAX ENGINE SPEED 2200MULTI DISK BRAKE PRESENT / NOT PRESENT PRESENTPARKING BRAKE SET 80% - 95% 95%PUMP POT. INVERTED ENABLE
3803�&86720,=(' $&&(77$%/(�9$/8( 67$1'$5'�9$/8(
TRAVEL PEDAL INC # 2,5 - 4 SEC 3TRAVEL PEDAL DEC. # 3 - 4 SEC 3,5SENSITIVITY 10% - 70% 50%INCHING PEDAL INC. 4 - 6 SEC 4INCHING PEDAL DEC. 1,5 - 2,5 SEC 2
(1*,1(�&86720,=(' $&&(77$%/(�9$/8( 67$1'$5'�9$/8(
TRAVEL PEDAL INC 0,5 - 3 SEC 1,8TRAVEL PEDAL DEC. 0,3 - 2 SEC 1,3MAST INC. 0,5 - 2 SEC 1MAST DEC. 0,8 - 2 SEC 1MAST FIXED CDM 1 0% - 100% 30%MAST FIXED CDM 2 0% - 100% 30%
# ONLY THESE VALUES CAN BE MODIFIED
CBD 2.5-3.0-3.5KUBOTA ENGINESETTING VALUE
&$/,%5$7,21�6(&7,21 $&&(77$%/(�9$/8( 67$1'$5'�9$/8(
MAST PRESENCE YES/NO YESMAX FORWARD SPEED 0% - 100% 100%MAX REVERSE SPEED 0% - 100% 100%NUMBER OF TEETH 1 - 200 9MULTI DISK BRAKE PRESENT / NOT PRESENT PRESENTPARKING BRAKE SET 80% - 95% 95%PUMP POT. INVERTED ENABLE / DISABLE ENABLE
3803�&86720,=(' $&&(77$%/(�9$/8( 67$1'$5'�9$/8(
TRAVEL PEDAL INC # 2.5 - 4 SEC 3TRAVEL PEDAL DEC. # 3 - 4 SEC 3,5SENSITIVITY 10% - 70% 50%INCHING PEDAL INC. 4 - 6 SEC 4INCHING PEDAL DEC. 1.5 - 2.5 SEC 2
(1*,1(�&86720,=(' $&&(77$%/(�9$/8( 67$1'$5'�9$/8(
TRAVEL PEDAL INC 0,5 - 2 SEC 1,2TRAVEL PEDAL DEC. 0,3 - 2 SEC 1MAST INC. 0,3 - 2 SEC 1MAST DEC. 0,3 - 2 SEC 1MAST FIXED CDM 1 0% - 100% 30%MAST FIXED CDM 2 0% - 100% 30%
# ONLY THESE VALUES CAN BE MODIFIED
LEGEND
DESCRIPTION ENGLISH DEUTSCH FRANCAIS ESPAÑOL
4' via 4th valve 4.Steuerkreis 4.ème levier 4a.leva5' via 5th valve 5.Steuerkreis 5.ème levier 5a.levaabilitazione attiva enable on Freigabe ein abilitation activée habilitación activadaabilitazione freni brakes enable Bremsenfreigabe abilitation des freins habilitación de los frenosabilitazione parcheggio parking enable Festellfreigabe abilitation de stationnement habilitación de aparcamientoacceleratore accelerator pedal Fahrpedal pédale accélérateur pedal aceleradoralternatore alternator Lichtmaschine alternateur alternadoranomalia centralina logic unit defect Logikeinheitsdefekt anomalie d’unité logique anomalía unidad lógicaattuatore actuator Aktuator actionneur actuadorarresto motore motor stop Motorstop arrêt du moteur parada del motorbatteria battery Batterie batterie bateríabobina coil Spule bobine bobinabrandeggio tilting Neigung inclinaison inclinacióncandele spark plugs Zundkerzen bougies d’allumage bujíascandelette glow plugs Glühkerzen bougies de chauffage bu jías incandescentechiave key Schlüssel clé llavechiave avviamento start key Anlaßschlüssel clé de démarrage llave de arranqueclacson horn Hupe klaxon claxoncomandi luci supplem. additional lights controls Zusatzbeleuchtungssteuerung commandes lumières suppl. mandos luces adicionalescomando elettroventola electric fan control Elektroflügelsteuerung commande électro-ventilateur mando electroventiladorcomando fanali stop stop lights control Stoplichtesteuerung commande feus de stop mando faroles de stopconn.batteria battery connector Batteriestecker connecteur batterie enchufe bateríacruscotto dashboard Armaturenbrett panneau de commande salpicaderodispositivo candelette glow plugs device Glühkerzevorrichtung dispositif bougie de chauffage dispositivo bujia incandescenteelettrovalvole marcia speed electrovalves Gangelektroventile electrovannes de marche electroválvulas de marchaelettroventola electric fan Elektroflügelrad électro-ventilateur electroventiladoremergenza emergency Notstand urgence emergenciafanali retromarcia reversing lights Rückfahrscheinwerfer feus de marche arrière faroles de marcha atrasfanali stop stop lights Stoplichte feus de stop faroles de stopfreno brake Bremse frein frenofreno pedale pedal brake Bremspedal frein pédale freno pedalfreno stazionamento parking brake Festellbremse frein de stationnement freno de aparcamientoindicatore riserva gas LPG reserve indicator GPL Reserveanzeiger indicateur réserve GPL indicador reserva GPL
LEGENDDESCRIPTION ENGLISH DEUTSCH FRANCAIS ESPAÑOL
indicatore temperatura ac water temperature indicator Wassertemperaturanzeiger indicateur temperature de l’ea indicador temperatura del aguaintas.filtro aria air filter clogging Luftfilterverstopfung encrassement filtre à air obstrucción filtro aireintas.filtro olio oil filter clogging Ölfilterverstopfung encrassement filtre huile obstrucció filtro aceiteintas.filtro olio idraul. hydraulic oil filter clogging Hydraulikölfilterverstopfung encrassement filtre huile hydr. obstrucción filtro aceite hidr.inversore inversor lever Umschaltung inverseur de direction palanca de inversióninversore manuale drive direction lever Handumschaltung inverseur de direction palanca de inversiónlivello carburante fuel level Treibstoffstand niveau carburant nivel carburanteliv.liquido freni brake fluid level Bremsflüssigkeitsstand jauge d’huile de freins nivel aceite frenosluci posteriori back lights Rücklichte lumières arrières luces traserasluci retromarcia reversing lamps Rückfahrlampen ampoule marche arrière lampara de marcha atrásmarcia avanti forward speed Vorwärtsgang marche avant marcha adelantemarcia indietro backward speed Rückwärtsgang marche arrière marcha atrásmarcia lenta slow speed langsamer Gang marche lente marcha lentamot.trazione traction motor Fahrmotor moteur de traction motor de tracciónmotore avviamento starter motor Anlaßmotor démarreur motor de arranquemotore idroguida power steering motor Hydrolenkungsmotor moteur direction assistée motor servodirecciónmotore pompa pump motor Pumpenmotor moteur pompe motor bombapedale freno brake pedal Bremsepedal pédale du frein pedal del frenopedaliera pedals Pedale jeu de pédales juego de pedalespedaliera doppia double pedals Doppelpedal pédales double pedales doblepompa pump Pumpe pompe bombapompa iniezione injection pump Einspritzungspumpe pompe d’injection bomba inyecciónpost combustione afterburning Nachverbrennung postcombustion postcombustiónpotenziometro sollev. lifting potentiometer Hubpotentiometer potentiomètre d’élévation potenciómetro levantamientopressione olio motore motor oil pressure Ölmotordruck pression d’huile moteur presión aceite motorpressostato freni brakes press.switch Bremsdruckschalter pressostat freins presóstato frenospulsante clacson horn push button Hupeknopf poussoir klaxon pulsador de claxonpulsante emergenza emergency.pushbutton Notdruckknopf poussoir d’urgence pulsador de emergenciarelè avviamento starter relay Anlaßrelais relais démarreur relé arranqueriserva gas LPG reserve GPL Reserve réserve GPL reserva GPLscatola acc. speed box Fahrschalter boitier du vitesse caja aceleradoressensore velocita’ speed sensor Geschwindigkeitsensor senseur de vitesse sensor de velocidadsollevamento lifting Hub élévation levantamientospia candelette glow plugs warning light Glühkerzenwarnlampe voyant bougies de chauffage luz testigo bujías incandescen.
LEGEND
DESCRIPTION ENGLISH DEUTSCH FRANCAIS ESPAÑOL
SW cofano bonnet switch Schutzhaubeschalter interrupteur coffre interruptor cofretemp.olio trasmis. oil temperature transmission Öltemperaturgetriebe temperature d’huile transmis. temperatura aceite transmisióntemperatura acqua water temperature Wassertemperatur temperature d’eau temperatura aguatermico thermal sensor Wärmesensor senseur thermique sensor térmicotraslatore sideshift Seitenschieber déplacement lateral desplazador lateraluomo presente deadman device Totmann-schalter Homme mort conductor presenteventola motore motor fan Motorflügel ventilateur moteur motor ventiladorventole fan Flügelräder ventilateur ventiladorvista posteriore rear view Rücksicht vue arrière vista rasera
COLORI COLOURS FARBEN COULEURS COLORESarancio orange Orange orange anaranjadoazzurro blue Hellblau bleu azulbianco white Weiß blanc blancoblu dark blue Blau bleu azulgiallo yellow Gelb jaune amarillogrigio grey Grau gris grismarrone brown Braun marron marronnero black Schwarz noir negrorosa pink Rose rose rosarosso red Rot rouge rojoverde green Grun vert verdeviola purple Violett violet violeta
Programmering av TCS-systemetBT Cargo CBD/CBG 2.5-5.0
A B C D E
F G H I J
K L M N O
P Q R S T
U V W X Y
Z
F1 F2 F3 F4
/ (
* )
- #
+,
=.
CTRLSHIFT
ESC
BKSPSPACE ENTER
1 2 3
4 5 6
7 8 9
0
Per Wärmlund / Avd. service
BT Cargo Teknikutbildning
Main Menu
Connect theconsole and turn thekey without starting
Press ENTERto select themain menu
Calibration
Display
PumpCustomised
EngineCustomised
FaultDetected
Information
Ph Parameters
Eeprom reset
Motor Shifting
Actuator Pid
Calibration of the potentiometers and the transmission actuators (pedals,control valve, engine actuator, etc.)
Display information on the transmission (engine RPM, transmissiondisplacement, micro switches status, etc.)
Personalization of the transmission behavior
System fault display
Software version
Not accessible (Password only)
Not accessible (Password only)
Not accessible (Password only)
Not accessible (Password only)
Personalization of the engine setting
Sida 1
ENTER
+
+
+
+
+
+
+
+
+
+
End of list 4.0 - 5.0t
End of list 2.5 - 3.5t
Programmering av TCS-systemetBT Cargo CBD/CBG 2.5-5.0
BT Cargo Teknikutbildning
To page 3Calibration Mast Lever
Sida 2
Calibration
ENTER
ENTER
ENTER
-
CalibrationCalibration Status
First operationto be carriedout to releasethe program
+
Calibrationcalibration Statuslocked
Select theparking brake
switch andpress +
CalibrationCalibration Statusnot locked
ESC
CalibrationTravel Pedal
Configurationaccelerator pedalpotentiometer
ENTER
Press a key
ENTER
ENTER ENTER
EN
TE
R
Press a keyENTER
ENTER
ESCAPE
ENTERPress a key
CalibrationTravel pedalDon’t touch thetravel pedal (’ENT’)
ENTER
ENTER
CalibrationTravel PedalIf Forward switchselect it (’ENT’)
Operate the forwardswitch lever or depressthe twin forward. Pedalto close switch
Operate the reverseswitch lever or depressthe twin reverse. Pedalto close switch
EN
TE
R
CalibrationTravel PedalForward complete(ENT)
CalibrationTravel PedalReverse complete(ENT)
Calibration TravelPedalFull depression inForward (Press a key)
Calibration TravelPedalFul depression inreverse (Press a key)
CalibrationTravel PedalForward complete(ENT)
Calibration Travelpedal. Don’t touchthe travel pedal(’ENT’)
CalibrationTravel PedalIf Reverse switchselect it (’ENT’)
CalibrationTravel PedalReverse complete(ENT)
CalibrationTravel PedalCompleted
+
CalibrationBrake / inchingpedal
Configurationbrake pedalpotentiometer Calibration
Brake / inching pedalRest reading(press a key)
Min value stored, CalibrationBrake inching pedalFull depression(press a key)
Completely pressthe pedal,keep it pressed Calibration
Brake / inchingpedal completed
Ended configuration of the brake pedal,
+ ESC
N.B. With the programlocked it is possible toread the sensor
values..
Calibration
Programmering av TCS-systemetBT Cargo CBD/CBG 2.5-5.0
BT Cargo Teknikutbildning
Sida 3
From page 2Calibration Mast Lever
CalibrationMast lever
Configuration of thelifting potentiometer,
ENTER
Pressa key
ENTER
CalibrationMast leverMast sensor presenceYES (1) NO (0)
Press 1 CalibrationMast leverRest reading(Press a key)
Min. Valuestored Calibration
Mast leverFull depression(press a key)
Pull the lifting lever tothe end stroke, keep itpulled,
CalibrationMast levercompletedEnded configuration of the
lifting potentiometer
+
+
+
+
+
+
+
+
+
+
+
+
++ + +
CalibrationEngine Calibration
CalibrationPump Neutral
Acquisition ofthe neutralpump position
ENTER
CalibrationPump neutralCompleted
Ended acquisitionof the neutralpump position
ACQUISITION TO BE CARRIED OUTWITH THE ENGINE ON
Calibrationmax.forward speed
CalibrationMax.reverse speed
CalibrationParking brake set
CalibrationMini engine set
CalibrationMaxi engine speed
CalibrationPump pot.inverted
CalibrationPump pot.inverted
FUNCTION TO BE CARRIED
OUT WITH THE ENGINE ON
CalibrationEngine calibration
Engine CalibrationLowest engine speedReading.......
Engine CalibrationHighest engine speedReading.....
CalibrationEngine CalibrationReading...(8 values)
Engine CalibrationEnd of enginecalibration
Ended acquisitionof the min. and maxRPM of the engine,
ESCAPE
ESCAPE
Acquisition of themin.and max.RPM of the engine
ENTER
Then the enginestarts to accelerateby itself
May be Modified
May be Modified
May be Modified
Standardvalue2250 RPM
Standardvalue850 RPM
NOT MODIFY
NOTMODIFY
NOTMODIFY
NOTMODIFY
NOTMODIFY
NOTMODIFY NOT MODIFY NOT MODIFY
ESCAPE
Back to calibration Back to calibration
CalibrationReduce speed
CalibrationNumber of teeth
CalibrationPower supply
CalibrationSensor excitation
CalibrationMulti disc brake
CalibrationParking brake set
LIST FOR 4.0-5.0tLIST FOR 2.5-3.5t
Calibration
Programmering av TCS-systemetBT Cargo CBD/CBG 2.5-5.0
BT Cargo Teknikutbildning
Sida 4
DisplayEngine Speed
Displaypump displacement
DisplayEngine command
DisplayAntistall
DisplayParking brake
DisplayBrake switch
DisplayMast engine Cmd
DisplayPump feed-back
DisplayDirection switch
DisplayMast switch
DisplayConstant speed
DisplayActuator feed back
DisplayReduced speed
DisplayPower supply
DisplaySensor excitation
DisplayNeutral drift
Display the real engine RPM
Display the pump displacementrequested by the logic unit (cc)
Display the engine RPMrequested by the logic unit
Display the status of thefunction (enable / disable)
Display the status of the negativebrakes (enable / disable)
Display the status of the parkingbrake switch (set / not set)
Display the engine RPMwith the lifting lever pulled
Display the real pump displacement(cc) by the potentiometer
Display the status of the direction switches(neutral / forward / backward)
Display the status of the control valve switches1=tilting / sideshift (set / not set)
Display the constant driving speed functionstatus with the lifting activated (set / not set)
Display the signal of the engineactuator in volts
Display the voltage of the logicunit (enable / disable)
Display the sensor voltage supplied by thelogic unit
Display the difference of the pump potentiometersignal from the theoretic value (in mV)
ENTER
ENTER
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
Displays informationof the engine andhydrostat pump
Calibration
Display
ESCAPE
ESCAPE
ENTER
ESC
ENTER
ESC
ENTER
ESC
ENTER
ESC
ENTER
ESC
ENTER
ESC
ENTER
ESC
ENTER
ESC
ENTER
ESC
ENTER
ESC
ENTER
ESC
ENTER
ESC
ENTER
ESC
ENTER
ESC
ENTER
ESC
ENTER
ESC
ENTER
ESC
DisplayNeutral drift
Display the reduced speed functionstatus (enable / disable)
Display the difference of the pump potentiometersignal from the theoretical value (in mV)
List for
4.0 - 5.0t
List for
2.5 - 3.5t
DisplayMenu
HOLD DOWN THE ENTERKEY TO DISPLAY DATA INSEQUENCE
Programmering av TCS-systemetBT Cargo CBD/CBG 2.5-5.0
BT Cargo Teknikutbildning
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER +
+
++
+
+
+
+
ESCAPE
ESC
ESC
ESC
ESCAPE
ESCAPE
ESCAPE
ESCAPE
ESC
Calibrationtravel Pedal
CalibrationCalibration status
CalibrationCalibration statusLocked
CalibrationCalibration statusNot Locked
-
Display
PumpCustomised
Pump CustomisedTravel pedal Inc.
Pump CustomisedTravel pedal Dec.
Pump CustomisedInching pedal Dec.
Pump CustomisedInching pedal Inc.
Pump CustomisedSensitivity
Pump CustomisedTravel pedal Inc.5.0 Seconds
Pump CustomisedTravel pedal Inc.5.0 Seconds
Pump CustomisedTravel pedal Dec.5.0 Seconds
Pump CustomisedTravel pedal Dec.5.0 Seconds
Sida 5
Set the requested value bytyping it directlywith the keyboard numbersor pressing + 0 -
( N.B. Stronger brake,lower valuesofter brake, higher value)
ENTER
Set the requested value by typing it directlywith the keyboard numbers or pressing + 0 -
( N.B. Quicker acceleration, lowervalue, slower acceleration, higher value)ENTER
Pump accelerationtime
Pump decelerationtime (Braking)
Not Modified
Not Modified
Not Modified
Select the Parking brakeswitch and press
Calibration statushas to be un lockedto release theparameters formodification
Pump CustomisedSection
Pump CustomisedHard brakingratio 00%
Pump CustomisedHard brakingratio 00%
Hard braking ratio
Calibration
See page 14
Programmering av TCS-systemetBT Cargo CBD/CBG 2.5-5.0
BT Cargo Teknikutbildning
ENTER
ENTER
ENTER
ENTER
ENTER ENTER
ENTER
ENTER +
+
ESCAPE
ESCAPE
ESCAPE
ESCAPE
ESC
Calibrationtravel Pedal
CalibrationCalibration status
CalibrationCalibration statusLocked
CalibrationCalibration statusNot Locked
-
Display
PumpCustomised
EngineCustomised
+
+
+
+
++
+
+
Select the Parking brakeswitch and press
Calibration statushas to be un lockedto release theparameters formodification
Engine CustomisedTravel pedal Inc.
Engine CustomisedMast fixed Cmd. 1
Engine CustomisedMast fixed Cmd. 145%
Engine CustomisedMast fixed Cmd. 145%
Engine CustomisedMast fixed Cmd. 2
Engine CustomisedMast fixed Cmd. 245%
Engine CustomisedMast fixed Cmd. 245%
Engine CustomisedMast Dec.
Engine CustomisedMast Inc.
Engine CustomisedTravel pedal Dec.
Set the requested value by typing itdirectly, or by the +0-(N.B. More RPM higher value less RPMlower value)
ENTER
Set the requested value by typing itdirectly, or by the +0-(N.B. More RPM higher value less RPMlower value)
ENTER
Engine RPMTilting
Engine RPMSideshift
Sida 6
Engine CustomisedSection
Calibration
Programmering av TCS-systemetBT Cargo CBD/CBG 2.5-5.0
BT Cargo Teknikutbildning
Calibration
Display
PumpCustomised
EngineCustomised
FaultDetected
Fault DetectedFault occuring now
Fault DetectedFault since startup
Sida 7
ENTER
+
+
+
++ +
+
+
DISPLAY CONSOLE
Pressto display the faults
ENTER
ENTER
ENTER To display thefaults in real time Fault detected
Fault occuring nowNo default
ES
C
ESC
ESC
No alarms
Fault detectedFault occuring nowActuator sensor
Alarm present
Fault detectedFault since startupStart of the list
To display thestored alarms (faults)(max 5)
To readthe alarms
Fault detectedFault since startupNeutral out of range
Fault detectedFault since startupEnd of the list
Alarms Section“Fault Detected”
Example:-
Programmering av TCS-systemetBT Cargo CBD/CBG 2.5-5.0
BT Cargo Teknikutbildning
Här är huvudmenyerna:
1 CALIBRATION
The CALIBRATION menu has two functions:
Cwhen the parking brake is locked and the “calibration status” parameter is “not locked”, it allows thecalibration and configuration of the system.
Dwhen the parking brake is not locked or the “calibration status” parameter is “locked” this menuviews the output voltages of the system sensors and the state of some components.
After calibration, release and engage the parking brake again to exit from the “calibration status” mode andreturn to the standard operating mode.
alibrating mode
isplay mode
N Meny Funktion
1 CALIBRATION Kalibrering av sensorer och potentiometrar. Visning av aktuellaspänningar (Calibration Status = Locked)
2 DISPLAY to display the information on the transmission (thermal engine speed,pump displacement, anitstall function,....)
3 PUMP CUSTOMIZED to customize the transmission (more or less prompt braking andacceleration)
4 ENGINE CUSTOMIZED to customize the thermal engine control (higher or lower accelerationof the thermal engine, engine speed when the tilt system and thesideshift are on,...)
5 FAULT DETECTED to display the system faults
6 INFORMATION software versions
7 PH PARAMETERS (password) configuration of the system operation parameters
8 EEPROM RESET (password) to reset the control unit memory
Sida 8
9 MOTOR SHIFTING(password) configuration of the parameters controlling the displacementShifting of the hydraulic motors
10 ACTUATOR PID (password) configuration of the actuator feedback parameter
BT Cargo Teknikutbildning Programmering av TCS-systemet
CALIBRATION MENU
N SUBMENU CALIBRATION MODE DISPLAY MODE
A Travel pedal calibration of the travel pedal display of the voltage supplied by thepotentiometer for the travel pedal
B brake / inching pedal calibration of the brake pedal display of the voltage supplied by thepotentiometer for the brake pedal
C mast lever calibration of the mast lever display of the voltage supplied by thepotentiometer for the mast lever
D engine calibration calibration of the actuator-thermal display of the voltage supplied by thepotentiometer for the actuator
E pump neutral calibration of the pump in neutral display of the voltage supplied by theposition potentiometer for the hydrostatic pump
F max forward speed limiting of the truck max display of truck forward speedforward speed (as a percentage of the max speed)
G max reverse speed limiting of the truck max display of the truck reverse speedreverse speed (as a percentage of the max speed)
H parking brake set definition of the brake pedal displays the brake pedal position inposition in which the mechanical which the mechanical brake is lockedpedal is engaged
I min engine speed definition of the minimum engine displays the minimum engine RPMRPM
L max engine speed definition of the maximum engine displays the maximum engine RPMRPM
M pump pot. Inverted definition of the connections type displays the connections typeof the pump potentiometer of the pump potentiometer
N calibration status validations and invalidation of the status of the calibration menucalibration menu
For the TCS to operate correctly, the voltage values read by the potentiometers in the pedals, the mastsystem and the motor actuator must not exceed the limits set. If the mechanical limit stops of thepotentiometer are not properly adjusted, the voltage supplied by the potentiometer is exceeded. The rangeof values allowed by the control unit disables the calibration procedure.Trouble may also occur after a correct calibration if, for whatever reason, the limit stop is modified.
Sida 9
O reduced speed limiting of the truck max. Speed displays if the truck reduced speed is(Enable / disable)
P number of teeth definition of the number of teeth display of the number of teeth/revPer engine rev (speed sensor inThe thermal engine
R power supply measures the supply voltage of measures the supply voltage ofControl unit the control unit
S sensor excitation measures the supply voltage of measures the supply voltage of theSensors sensors
T multi disc brake definition of the type of brake type of brake usedUsed
BT Cargo Teknikutbildning Programmering av TCS-systemet
CALIBRATION AND FIRST START UP OF THE TRANSMISSION SYSTEM
The system calibration is to be performed when the thermal engine is stopped.The following are to be calibrated:
Potentiometer for the travel pedal (TRAVEL PEDAL)
Release the parking brakeposition the steering column switch to forward geargradually press the forward pedal: wheels should slowly rotate forward
When wheels rotate forward, check that the voltage of the pump feedback potentiometer increases from2.5 to 5 volts (for the voltage reading use “pump neutral” parameter in the “calibration” menu).Check the correct operation under the following conditions:
- mast lifting, sideshift and tilt operation, etc., : if the relevant levers are adjusted, the thermal enginewill accelerate
- forward / reverse speed and braking- parking brake: if engaged, the travel pedal will be disabled (the engine RPM will increase, but thetruck wheels will be locked)
- emergency button.
CAUTION: the hydraulic motors must not rotate quickly when wheels are jacked up
Potentiometer for the brake pedal (BRAKE / INCHING PEDAL)Potentiometer for the mast lever (MAST LEVER)Potentiometer for the hydrostatic pump (PUMP NEUTRAL)
While calibrating, check the parameters below:
Max. forward speed (truck max speed) 100%Max reverse speed (truck max speed) 100%Parking brake set (brake setting) 95%Min engine speed(minimum engine RPM) 850Max engine speed (maximum engine RPM) 2250Pump pot. Inverted (with Potentiometer Hall effect only) Enable
Calibration also includes the actuator setting while the thermal engine is running (ENGINE CALIBRATION).For the engine calibration do the following:
Lift the truck onto the blocks
fill the hydraulic circuit and bleed the air from the system
engage the parking brake
select the neutral position (through the steering-wheel operated reverse gear)
start up the engine and wait for the stabilization of the boost pressure
adjust the engine min and max RPM through the actuator limit stop screws (the limit stops are to beobtained on the actuator support, on the injection pump). The engine RPM is to be measuredthrough the “engine speed”parameter in the “DISPLAY” menu.
Calibrate the actuator (ENGINE CALIBRATION)
Press the accelerator pedal; the actuator has to rotate clockwise and the voltage of thefeedback potentiometer in the actuator has to increase (such voltage may be measured in the“engine calibration” parameter in the “calibration” menu after engaging the parking brake).
Once the calibration procedure is over, check the transmission operation (wheels must be jacked up):
not
Sida 10
BT Cargo Teknikutbildning Programmering av TCS-systemet
A) TRAVEL PEDAL CALIBRATION
B) BRAKE / INCHING CALIBRATION
C) MAST LEVER CALIBRATION
For calibrating, voltages are not to exceed the following ranges (voltages may be read in display mode).
Pedal in its min. position 0,35 - 2,4 volts (7 - 48% of the supply voltage)Pedal in its max.position 2,6 - 4,65 volts (52 - 93% of the supply voltage)(the supply voltage of all sensors is of 5 volts)
Defines the voltage values corresponding to the min. and max. positions of the brake pedal ( and the“ inching” function.
For calibrating, voltages are not to exceed the following ranges:
Pedal in its min. position 0,35 - 2,4 volts (7 - 48 % of the supply voltage)Pedal in its max. position 2,6 - 4,65 volts (52 - 93% of the supply voltage)
Defines the voltage values corresponding to the maximum and minimum positions of the mast lever.
For calibrating, voltages are not to exceed the following ranges:Lever in neutral position 0,35 - 2,3 volts (7 - 46 % of the supply voltage)Lever fully pulled 2,4 - 4,65 volts (48 - 93% of the supply voltage)
Matches the actuator position angle (voltage of the actuator feedback potentiometer) with the enginespeed value.
For calibration, voltages are not to exceed the following ranges:
Actuator in its min. position 0,35 - 2,4 volts (7 - 48 % of the supply voltage)Actuator in its max. position 2,6 - 4,65 volts (52 - 93% of the supply voltage)
Such values may be viewed if the parking brake is engaged.The control unit automatically controls the actuator by bringing it to its minimum and maximum positions(that are determined by the mechanical limit stops located on the actuator support). With respect to themin.and max. Positions, TCS reads the min.and max RPM as well as some intermediate values.The limit stops are to be obtained on the actuator, not on the injection pump.
Defines the voltage corresponding to the neutral displacement position of the hydrostatic pump (feedbackpotentiometer).
The voltage value must not exceed the following range 2.48 to 2.52 volts.(In display mode and when the truck is running, the voltage value must vary. When the wheels rotateforward, the potentiometer voltage must rise to 5 volts and remain
D) ENGINE CALIBRATION
E) PUMP NEUTRAL CALIBRATION
constant).
Sida 11
SEE THE DIAGRAM FOR USING CONSOLESECTION “CALIBRATION”
BT Cargo Teknikutbildning Programmering av TCS-systemet
Sida 12
This parameter (expressed as a percentage of the truck’s forward max. speed) limits the travel speed.This parameter may be modified (in calibration mode).
This parameter (expressed as a percentage of the truck’s reverse max speed) limits the travel speed.This parameter may be modified (in calibration mode).
This parameter defines the stroke of the brake pedal necessary to engage the mechanical brake. Thestandard value is 95%. It is suggested that this value is not changed. Limit values: 90 to 95%.
This parameter defines the minimum engine RPM (standard value 850).
This parameter defines the maximum engine RPM (standard value 2250)
This parameter defines the type of connections at the pump potentiometer. This parameter is present withthe Hall potentiometer software only.
This parameter enables or disables the calibration mode.
This parameter expressed if the truck reduced speed is activated (enable / disable). This parameter maybe modified (in calibration mode).
This parameter defines the number of pulse per revolution of the thermal engine sent by the speed sensorto the control unit.
Displays the supply voltage of the control unit: battery voltage (12 volts)
This parameter displays the voltage supplied by the control unit to the sensors. Correct value: 5 volts.
this parameter defines whether the multidisc brake is fitted or not (the multidisc brake is an on/off brake,i.e. It is not gradual.
F) MAX FORWARD SPEED
G) MAX REVERSE SPEED
H) PARKING BRAKE SET
I) MIN ENGINE SPEED
L) MAX ENGINE SPEED
M) PUMP POT. INVERTED
N) CALIBRATION STATUS
O) REDUCED SPEED
P) NUMBER OF TEETH
R) POWER SUPPLY
S) SENSOR EXCITATION
T) MULTI DISC BRAKE
SEE THE DIAGRAM FOR USING CONSOLESECTION “CALIBRATION”
BT Cargo Teknikutbildning Programmering av TCS-systemet
2) DISPLAY
This menu displays the transmission data.Press ENTER to display data (e.g. Thermal engine speed).
(Hold down the key to display data in sequence)
Real speed of the thermal engine (expressed in RPM)
Pump displacement required by TCS (expressed in cc). Warning: this is the displacement control sentby the control unit to the pump, so the value displayed may be different from the real displacement.
Speed of the thermal engine required by TCS (in RPM).
Indicates whether the anitstall function is enabled or not (enable / disable).
Displays whether the negative brakes are set or not (set / not set).
Displays whether the parking brake switch is set or not (set / not set)
Speed of the thermal engine required by TCS (in RPM) when the mast is actuated.
Actual displacement of the pump (expressed in cc). This is the displacement measured by thepotentiometer located on the pump.
Displays the running direction controlled by the pedal micro-switches or the steering-wheel operatedreverse gear (neutral / forward / reverse).
Displays the state of the valve bank microswitches 1 = tilt / sideshift (set / not set)
.Displays the constant speed function enabling when the mast is actuated while the truck is running(set / not set).
Displays if the reduced speed function is enabled (the trvel speed is limited to a preset percentagevalue of the max. speed). optional
Displays the engine actuator signal in Volts. Increases during acceleration and vice versa.
Displays the voltage supply to the control unit: battery voltage (12V)Must be between 9,5 and 48,5 Volt.
Displays the voltage supply to the sensors. Correct value 5 Volt.
Displays the difference in value between the theoretical and real pump potentiometer value (in mV)This parameter is present with the Hall potentiometer software only.
ENGINE SPEED
PUMP DISPLACEMENT
ENGINE COMMAND
ANTISTALL
PARKING BRAKE
BRAKE SWITCH
MAST ENGINE COMMAND
PUMP FEED-BACK
DIRECTION SWITCH
MAST SWITCH
CONSTANT SPEED
REDUCED SPEED
ACTUATOR FEED BACK
POWER SUPPLY
SENSOR EXCITATION
NEUTRAL DRIFT
Sida 13
BT Cargo Teknikutbildning Programmering av TCS-systemet
3) PUMP CUSTOMIZED
Sets the parameters for the control of the hydrostatic pump.This parameter is used to modify the acceleration and deceleration of the truck.Enable the program to modify such values (calibration status - not locked).
This parameter defines how long the pump takes to reach its max displacement when the travel pedalis fully pressed (the higher the value of this parameter, the less the acceleration of the truck).
This paramter defines how long the pump takes to reach its neutral displacement mode when thetravel pedal is released (the higher the value of this parameter, the less the deceleration of the truckduring the hydrostatic braking).
This parameter (%) changes the release braking value (travel pedal dec) as the following table:
Travel pedal dec (s) 2 5 7 10
Hard braking ratio (%)
0 2 5 7 10
17 1.7 3.8 5 6.5
50 - 2.8 - -
67 1.6 2.5 3.1 3.6
83 - 2.3 - -
100 1.3 2.1 2.5 2.9
TRAVEL PEDAL INC.
TRAVEL PEDAL DEC.
HARD BRAKING RATIO
Braking times of the truck function of the two parameters“Travel pedal dec” (s) and Hard braking ratio”(%)
SENSITIVITY
INCHING PEDAL INC
INCHING PEDAL DEC.
This parameter defines the sensitivity of the pump control when varying the pedal stroke (this value isexpressed as a percentage of the pump max. displacement control).
This parameter defines how long the pump takes to reach it’s max. displacement when the inching pedalis instantaneously released after it has been fully pressed in conjunction with the travel pedal.
This parameter defines how long the pump takes to range from the max. Displacement to the neutraldisplacement when the inching pedal is instantaneously pressed after fully pressing the travel pedal.
Sida 14
BT Cargo Teknikutbildning Programmering av TCS-systemet
Bromskraft vid låghastighet
Bromskraft vid höghastighet
4) ENGINE CUSTOMIZED
Sets the parameters for the thermal engine control. Do not modify the standard values.
This parameter defines how long the actuator takes to achieve its stroke when the travel pedal is fullypressed (the higher the value of this parameter, the longer the time the thermal engine takes to rangefrom its min RPM to its max RPM.)
This is the same as the previous parameter (the time the thermal engine takes to range from its minspeed to its max. Speed.)
This parameter defines the time the actuator takes to achieve its stroke when the mast lever is fullypulled back. (The higher the value of this parameter, the longer the time the thermal engine takes torange from its min RPM to its max RPM)
This parameter is similar to the previous one (time the engine takes to range from its max RPM to itsmin. RPM when the mast lever is released).
Parameters that define the thermal engine speed rate when one of the auxiliary devices of the hoistingunit is actuated (tilt unit, sideshift, 4th way, 5th way).When one of the value levers is actuated (except for the mast lever) the engine speed increases by aquantity proportional to the parameter setting. Standard value is 30 - 40 %
Ex: Engine min speed: 700 rpm; engine max.speed: 2,500rpmusable range: 2,500 - 700 = 1,800rpmparameter (mast fixed cmd): 25%If the engine operates at a speed higher than 1,100rpm and the distributor is actuated, theactuator will bring the engine rpm to: 1,100 + (2,500 - 700) x 0.25 = 1,500rpm
Do not increase the speeds set to avoid dangerous manoeuvres.Stroke of the sideshift: 2 - 2.5secsTilting: 4.5 - 5 secs
(Available from 2001)Parameter which defines the max thermal motor rpm when the lifting is started. By activating the lever,the motor speed increases step by step until the max value set.
TRAVEL PEDAL INC.
TRAVEL PEDAL DEC.
MAST INC.
MAST DEC.
MAST FIXED CMD 1
MAST FIXED CMD 2
MAST MAXIMUM CMD
Sida 15
BT Cargo Teknikutbildning Programmering av TCS-systemet
5) FAULT DETECTED
- FAULT OCCURRING NOW
- FAULT SINCE START UP
- FAULT MESSAGES SHOWN ON THE CONSOLE
Displays the system faults.
Press enter to display the current fault
Press (+) and (-) to display the last five faults occurred
The excitation voltage of the sensor is <2V or >5.5V
The supply voltage of TCS control unit is <9.5V or >32V for morethan 2 secs long
The signal (voltage) of the travel pedal potentiometer hasexceeded the limits set while calibrating
The signal (voltage) of the brake pedal potentiometer hasexceeded the limits set while calibrating
The signal (voltage) of the mast lever has exceeded the limitsset while calibrating
The signal (voltage) of the feedback potentiometer has exceedthe limits set while calibrating
>20% error, for more than 0.5secs, between the actuator setpointand the potentiometer feedback
>20% error, for more than 0.5 secs, between the pump controlsignal and the potentiometer feedback signal in the pump.
Pump feed back is <0.25V or >4.75V
During calibration the pump neutral is outside of the fixed limits
“ The difference between the pump in neutral calibration functionand the pump in neutral while the values are fed is >341 mV
The pump feedback changes too fast in comparison with the realchange of the pump displacement.
One parameter at least is outside of the field of acceptable values
“Excitation Sensor”
“Power Supply”
“Travel Pedal Sensor”
“Brake / Inching pedal Sensor“
“Mast lever Sensor”
“Actuator Sensor”
“Error on Actuator control loop”
“Error on pump control loop”
“Feed back error“
“Neutral out of range”
Pump neutral drift too high”
“Feedback moves too fast”
“Eeprom error at address”
Sida 16
“Direction switches error”
“Other default”
The TCS control unit takes contemporarily the forward and reverse gear(running mode) started
Other faults
6) INFORMATION
Displays the SOFTWARE version
BT Cargo Teknikutbildning Programmering av TCS-systemet
7) PH PARAMETERS
- PASSWORD
PUMP NEUTRAL OFFSET
- ENABLE LIMIT CHANGE
- INVERSION BRAKING
- INVERSION DISPLACEMENT
- DISABLE PUMP DELAY
- REGULATOR OFFSET
Enter the password (4 numbers) with the digital key and then valid (enter).Press the key / esc then (+) or (-) in order to have access to the rest of the menu
-This parameter is used to offset pump feedback
During the calibration of the pedals, the auxiliary levers and the actuator, it is possible that the minimumand maximum values obtained on the potentiometer do not conform to the limits fixed by the programme.It is possible to modify these limits.In the menu calibration, authorise the mode calibration. Go into the menu “PH PARAMETERS”and intothe menu “ENABLE LIMIT CHANGE”.It is necessary to be in “NOT LOCKED”
This function is used to have a braking action if the direction switch is set to the reverse position during theoperation of the machine (plug braking)The braking action will be proportional to the position of the travel pedal.
This parameter sets the inversion time range from 0 - 10 seconds
Parameter which defines the time delay of the negative brakes releasing (standard values 30 cycles). It isthe delay for the brakes releasing after the pump has reset its displacement. In order to have the brakesrelease in a short time, for example on a ramp, reduce the value (min 5 max 45 cycles).
This is the acceptable difference between the requested engine speed and the measured engine speed.If this value is exceeded, the antistall function is active
Sida 17
- ANTISTALL COEF
- DERIVE ANTISTALL
- FULL STROKE CMD
- ENGINE DELAY INC
coefficient applied to the action of the anitstall function.The parameter change from 3 to 8The higher the value the more the displacement will decrease
Definition of the derived gain for the antistall action. The parameter is a variable number from 10 - 30The higher the number the more sensitive antistall is to RPM variations
Compensation of the electric stroke used on the position potentiometer of the pump swashplateThe parameter is a number (never vary it) 1488
This parameter is used to take into account the reaction time of the engine actuator in order to activate theanitistall at the right moment. It avoids unnecessary operations of the antistall functions.
This value is the complementary value of engine delay dec. It is to take into account during the engine decelerationThis paramter is the time taken for engine deceleration.
- ENGINE DELAY DEC
BT Cargo Teknikutbildning Programmering av TCS-systemet
8) EPROM RESET
- PASSWORD
- ALL EEPROM RESET
- FAULT LIST RESET
This menu is used to reset the data of the EEPROM
Enter the password (4 numbers) with the digital key and then press enter.Press the key / esc then (+) or (-) in order to have access to the rest of the menu
Press the enter key to cancel the list of statistics
Press the enter key to cancel the list of the detected faults.
Sida 18
BT Cargo Teknikutbildning Programmering av TCS-systemet
Sida 19
TROUBLES OCCURRING WHILE CALIBRATING
1) TRAVEL PEDAL
Travel pedal position out of range
Release the parking brake
Select theTRAVEL PEDAL submenu
Voltage = 0 volts?
Check the potentiometer wiringHold down the [ENTER] key andcheck if voltage changes whenthe pedal is pressed
Does voltage change?
Press the [ENTER] key tomeasure the min. and max.Voltage supplied by thepotentiometer
Adjust the mechanical limit stop ofthe pedal so that the voltage doesnot exceed the ranges set(see “travel calibration”)
Check the potentiometer wiring
Yes No
No
Yes
(Error message)
The terminal will display thevoltage that is suppliedfrom the potentiometer inthe travel pedal
Calibrate the travel pedal
The terminal will switch from theCALIBRATION MODE to theDISPLAY MODE
The voltage values read by the transmission potentiometer (pedals, hoisting, etc.) Must not exceed the limits set. Ifthere is some wiring failure or the mechanical limit stops of the potentiometers are not properly adjusted, the voltagethey supply will exceed the allowed range for the control unit, thus preventing the calibration procedure. In thatcase, the terminal will display one of the following messages (while calibrating or in the “fault detected” alarmmenu).
Travel pedal position out of range Travel pedalBrake/inching pedal sensor Brake pedalMast lever sensor Mast leverActuator position out of range Thermal engine actuatorFeed back error Hydrostatic pump potentiometer
BT Cargo Teknikutbildning Programmering av TCS-systemet
Sida 20
TROUBLES OCCURRING WHILE CALIBRATING
2) BRAKE/INCHING PEDAL
Brake/inching position out of range
Release the parking brake
Select theBRAKE/INCHING PEDAL submenu
Voltage = 0 volts?
Check the potentiometer wiringHold down the [ENTER] key andcheck if voltage changes whenthe pedal is pressed
Does voltage change?
Press the [ENTER] key tomeasure the min. and max.Voltage supplied by thepotentiometer
Adjust the mechanical limit stop ofthe pedal so that the voltage doesnot exceed the ranges set(see “travel calibration”)
Check the potentiometer wiring
Yes No
No
Yes
(Error message)
The terminal will display thevoltage that is suppliedfrom the brake pedalpotentiometer
Calibrate the brake pedal
The terminal will switch from theCALIBRATION MODE to theDISPLAY MODE
BT Cargo Teknikutbildning Programmering av TCS-systemet
Sida 21
TROUBLES OCCURRING WHILE CALIBRATING
3) MAST LEVER
Mast lever sensor out of range
Release the parking brake
Select theMAST LEVER submenu
Voltage = 0 volts?
Check the potentiometer wiringHold down the [ENTER] key andcheck if voltage changes whenthe pedal is pressed
Does voltage change?
Press the [ENTER] key tomeasure the min. and max.Voltage supplied by thepotentiometer
Check the potentiometer wiring
Yes No
No
Yes
(Error message)
The terminal will display thevoltage that is suppliedfrom the mast leverpotentiometer
Calibrate the mast lever
Adjust the shims of thepotentiometer support bracket sothat the voltage does not exceedthe ranges set (see “mast levercalibration”) If the lever is movedforward from its middle position(for forks lowering) voltage is notto decrease.
The terminal will switch from theCALIBRATION MODE to theDISPLAY MODE
BT Cargo Teknikutbildning Programmering av TCS-systemet
Sida 22
TROUBLES OCCURRING WHILE CALIBRATING
4) THERMAL ENGINE ACTUATOR
Actuator position out of range
Release the parking brake
Select theENGINE CALIBRATION submenu
Voltage = 0 volts?
Check the electrical connectionsof the actuator
Hold down the [ENTER] key andcheck if voltage changes while theactuator rotates
Does voltage change?
Press the [ENTER] key tomeasure the min. and max.Voltage supplied by theactuator potentiometer
Check the actuator electricalconnections
Yes No
No
Yes
(Error message)
The terminal will switch from theCALIBRATION MODE to theDISPLAY MODE
The terminal will display thevoltage that is suppliedby the potentiometer ofthe actuator
Calibrate the actuator
Adjust the length of the tie rod sothat the voltage does not exceedthe ranges set (see “enginecalibration”)
Engage theparking brakeand press theacceleratorpedal
BT Cargo Teknikutbildning Programmering av TCS-systemet
Sida 23
TROUBLES OCCURRING WHILE CALIBRATING
5) POTENTIOMETER IN THE HYDROSTATIC PUMP
Feed back error
Release the parking brake
Select thePUMP NEUTRAL submenu
Voltage = 0 volts or 5 volts
Check the potentiometerelectrical connections
Voltage = 2.48 - 2.52 volts
Yes No
No
Yes
(Error message)
The terminal will switch from theCALIBRATION MODE to theDISPLAY MODE
The terminal will display thevoltage that is suppliedby the potentiometer in thehydrostatic pump
Check the potentiometer wiring, liftthe truck onto blocks, electricallydisconnect the pump solenoidvalves and start up the engine: Ifthe pump supplies some oil, thetrouble is hydraulic or mechanical(mechanical maladjustment of thepump plate positioning in neutral)After disconnecting the valves, if thepump supplies some oil, switch offthe engine and hold down the[ENTER] key in order to read thevoltage, until a 2.5 volt value isobtained
Engage the parking brake,switch to CALIBRATIONmode and clibrate thepump potentiometer tozero.
Engage the parking brake, swich toCALIBRATION mode and clibratethe pump potentiometer zero.
BT Cargo Teknikutbildning Programmering av TCS-systemet
Sida 24
SYSTEM FAULTS AND FAILURES
Any system failure is signalled by the flashing warning light located beside the valve bank levers.The frequency indicated the failure importance.The kind of fault is displayed in the FAULT DETECTED menu (FAULT OCCURRING NOW SUBMENU).If the warning light blinks slowly (0.5Hz) the fault is not very important; the machine is able to drive.
Error message Cause Cure
Travel pedal sensor
The signal voltage of the travel pedalpotentiometer has exceeded the limits setwhile calibrating.Connector disconnected or wrong wiring.
The signal voltage of the brake pedalpotentiometer has exceeded the limits setwhile calibrating.Connector disconnected or wrong wiring.
The signal voltage of the mast leverpotentiometer has exceeded the limits setwhile calibrating.Connector disconnected or wrong wiring.
The signal voltage of the feedbackpotentiometer has exceeded the limits setwhile calibrating.Connector disconnected or wrong wiring.
Check the potentiometerwiring.Check if the voltage values atthe pedal stop do not exceedthe preset limits.Adjust the pedal limit stop.Calibrate the pedal again.
Check the potentiometerwiring.Check if the voltage values atthe pedal stop do not exceedthe preset limits.Adjust the pedal limit stop.Calibrate the pedal again.
Check the potentiometerwiring.Check if the voltage values atthe lever stop do not exceedthe preset limits.Adjust the lever limit stop.Calibrate the lever again.
Check the potentiometerwiring.Check if the voltage values atthe actuator stop do notexceed the preset limits.Adjust the actuator limit stop.Calibrate the actuator again.
Brake/inching pedal sensor
Mast lever sensor
Actuator sensor
Error on actuator controlloop
This message may bedisplayed if the acceleratoris pressed(green light on)when the engine is off andthe brake is unlocked.
.20% error, for more than 0.5 secretary..Between the actuator set point and thepotentiometer feed back.Connector disconnected or wrong wiring.
Check the actuator wiring.Check the actuatorpotentiometer output signal. Ifyou press the acceleratorpedal, the actuator will rotateforward and the voltage -measured in engine calibrationwhen the brake is released -will increase.
Power supply out of range The supply voltage of TCS control unit isnot within the 9.5 - 48 volt range.
Check the supply voltage value.
BT Cargo Teknikutbildning Programmering av TCS-systemet
Sida 25
SYSTEMFEL OCH FELMEDDELANDEN
Om varningslampan blinkar snabbt (1hz) är felet allvarligt, och maskinen går ej att köra!
FELMEDDELANDE ORSAK KONTROLLERA
Excitation voltage
Felaktig matningsspänning till sensoreroch microbrytare.
- Att spänningen ligger på 5 volt+/- 5%
Feedback error
Fel signal från feedback-potentiometernpå pumpen.
Fel signal från feedback-potentiometernpå pumpen, med pumpen i neutralläge.
- Att spänningen från feedback-potentiometern ligger på 2.5 +/-0.15 volt när pumpen står ineutralläge.
Neutral out of range
- Att spänningen från feedback-potentiometern ligger på 2.5 +/-0.15 volt när pumpen står ineutralläge.
Error on pump control loop
Fel signal från feedback-potentiometernpå pumpen. Avvikelsen mellan feedbacksignalen och det förväntade värdettillbaka till TCS kontrollen är >20%, i merän 0.5 sec.
- Kablaget till feedback-potentiometern och EDCkontrollen.
- Att feedback signalen ändrarsig när man ökar körhastigheten.
- Att Min och Max spänningenfrån feedback potentiometern ärkonstant, och att värdet är likavarje gång. Spänningen skallstiga till upp emot 5 volt.
BT Cargo Teknikutbildning Programmering av TCS-systemet
Sida 26
FELSÖKNING
Typ av fel Möjlig orsak
Motorn går men ingen drivning.Pumpen vinklar inte ut, varkenframåt eller bakåt.
Kontrollera p-broms brytarens funktion i menyn: "DISPLAY /BRAKE SWITCH" (set / not set).
Kontrollera fram&back brytarnas funktion i menyn: "DISPLAY /DIRECTION SWITCH" (neutral / forward / reverse).
Drivningen fungerar och pumpenvinklar ut, men motorn varvarinte upp.
Kontrollera varvtalssensorns funktion i menyn: "DISPLAY/ENGINESPEED" - värdet skall vara relevant till det verkliga motorvarvet.
Kontrollera feedback signalen från pump-potentiometern i menyn:"CALIBRATION / PUMP NEUTRAL" (calibration status = locked)
Kontrollera gasmotorn funktion i menyn: "CALIBRATION / ENGINECALIBRATION" (calibration status = locked)
Drivningen fungerar och motornvarvar upp vid körning.Inget gaspådrag när mananvänder hydraulfunktionerna.
Kontrollera lyftpotentiometerns funktion i menyn:"CALIBRATION / MAST LEVER / MAST SENSOR PRESENCE"(Yes=1/ No=0)
(calibration status = locked)
Kontrollera Tilt/Aux brytarnas funktion i menyn: "DISPLAY / MASTSWITCH" (set / not set).
Kontrollera lyftpotentiometerns funktion i menyn:"CALIBRATION/MAST LEVER"
Varken drivning eller gaspådragfungerar.
Om varningslampan är släckt:
:
:
Kontrollera varvtalssensorns funktion i menyn: "DISPLAY/ENGINESPEED" - värdet skall vara relevant till det verkliga motorvarvet.
(calibration status = locked)
Kontrollera spänningsmatningen till TCS enheten i menyn:
Kontrollera feedback signalen från pump-potentiometern i menyn:"CALIBRATION / PUMP NEUTRAL" (calibration status = locked)
Om varningslampan blinkar sakta
Om varningslampan blinkar snabbt
Kontrollera signalen från gaspedalen i menyn: "CALIBRATION/TRAVEL PEDAL CALIBRATION" .
Kontrollera spänningsmatningen till sensorerna i menyn:"DISPLAY / SENSOR EXCITATION" (5 volt).
"DISPLAY / POWER SUPPLY"
Kontrollera kablaget till EDC-kontrollen.
BT Cargo Teknikutbildning Programmering av TCS-systemet
Recommended