View
1
Download
0
Category
Preview:
Citation preview
the perfect fusion
Catalogue
p.
3
Dear Doctors,
We are pleased to introduce our new MG In-Hex Catalogue 2015.
Established in Valladolid (Spain) in 1996, Mozo-Grau was created to offer a service
by developing, researching, designing and launching new reliable products and
solutions for the field of implantological oral surgery, based on the experience of
respected professionals.
Quality, innovation, and science are among the fundamental bases on which Mozo
Grau sets its activities. Mozo Grau has been audited and certified to be in conformance
with local, European and international standards. Its high quality standards demand
parts to be produced with specifications accurate to within 10 microns (0.01 mm)
and 100% verification of the parts manufactured to pass through a series of rigorous
tests before shipping.
As evicence of what science means to Mozo-Grau is our Scientific Summary which
gathers over 50 scientific articles on experimental and clinical studies, and a collection
of selected clinical cases performed with Mozo Grau dental implants. The best
guarantee of Mozo-Grau quality and constant improvement is the research team´s
trust and confidence.
As for innovation, Mozo Grau is focused in increasing the added value of its production
and quality. In this regard, Mozo Grau has launched MG Código Explorer®, a unique
numeric code which identifies every single MG dental implant. This code allows
doctor and patient to have full traceability and knowledge of the implant. Patients
receive their Código Explorer® on a MG Implant Card®, a very comfortable form to
carry information everywhere (see page 11 for further information).
Valladolid, October 2014Castilla y León Young Businessman of
the Year Award. Valladolid 2003
AQVA Quality and Business Management Award. Madrid 2003
The Bizz Award for Excellence in Quality Houston -Texas (USA) 2005
Entrepeneur of the year award.Castilla y Leon 2012
Quality Award. Executive Magazine 2013
Enterpreneur of the Year Award (Category: Industry). Castilla y León 2012
Best Quality Manager Award. Castilla y León 2014
Quality
Quality: Mozo-Grau Principle
p. 4
Clients testimonials
The definition of the Spanish Royal Academy of the Language
for quality is: “property or set of inherent properties to a thing
that allow to appreciate it like equal, better or worse than the
rest of its type”.
The strict reading of this definition places the quality of a pro-
duct as a comparison to the quality offered by its competi-
tors. At Mozo-Grau this comparison is not enough. Our aim is
not only to be better than the rest, but to work to satisfy our
clients by offering the most advanced science and techniques.
Our Quality Control and Engineering Department set up
analysis systems and verification procedures to avoid mistakes
from the first stages of production. In this way we are able
to develop solid and efficient processes that guarantee 100%
reliability on all the products and services.
ISO 13485:2003 is an ISO standard, published in 2003, that re-
presents the requirements for a comprehensive management
system for the design and manufacture of medical devices.
The Medical Devices Directive (Council Directive 93/42/EEC)
is intended to harmonize the laws related to medical devices
within the European Union. ISO 9001:2008 requires the or-
ganization to demonstrate continuous improvement. The CE
marking (also known as CE mark) is a mandatory conformity
mark on many products placed on the single market in the
European Economic Area (EEA).
Mozo-Grau complies with all these mandatory certifications
and regulations necessary to supply implants in the European
Union, moreover Mozo Grau is voluntarily complying with the
most exigent standards on the subject.
At Mozo-Grau we are proud of the trust placed on us by our
clients every time they purchase one of our products. This con-
fidence compels us to meet their expectations.
“The best quality control any company can have is a satisfied client”.
“I´m really pleased to collaborate with a company which is truly interested in the correct evalua-tion of its products and that also promotes the clinical researching with the aim of solving important problems for our patients“.
Dr. Marco EspositoChief editor European Jour-nal of Oral Implantology. Italy. 23/08/2012
“In my opinion Mozo-Grau is at the very forefront among the most important companies in the Implantology sector. Its concern and support to research, its ex-haustive quality controls, its innovation capability and its closeness to the profes-sionals in the field, predicts undoubtedly a great future full of success, both from a scientific point of view and from a profes-sional and commercial”.
Dr. Eduardo EstefaníaDirector of Master in Periodontics UPV, Dental Clinic Medical Director UPV.11/09/2012
“Nowadays there are many com-panies that manufacture implants. So, what makes the difference? How to choose between one or the other?. In my opinion, there are two essential elements: accu-racy or adjustment between the different parts that must articulate to achieve a perfect restoration and the closeness between those who manufacture implants and those who use them. Both factors are fully complied by Mozo-Grau”.
Dr. Carlos LarruceaUniversity of Talca. Chile.29/08/2012
“I have been using exclusively Mo-zo-Grau implants for 12 years, both in ordinary patients as well as in oncologic under radiotherapy treat-ment. The implant quality is ex-traordinary and it is at the highest level among the companies in the sector. Besides, Mozo-Grau is also concerned about the knowledge disclosure, organizing courses with lectures of the highest international level in all the countries where it is set. For Mozo-Grau the continu-ous investigation is its first objec-tive, and so it organizes researching programmes in many Spanish and foreigners universities. On the other part, the service and assistance of the professionals is very good, fast and exquisite”.
Profesor. D. Carlos Navarro VilaProfessor of Oral Surgery and Max-illofacial of the Faculty of Medicine at the Complutense University of Madrid . Chief Professor of Oral and Maxillofacial Surgery of University General Hospital Gregorio Marañon in Madrid. President of the European Board of Oral and Maxillofacial Sur-gery.29/09/2012
“The relationship between the Master of Oral Surgery at the University of Seville and Mozo-Grau comes from nearly 5 years and has always been conducted at the highest level, both in the clinical as well as the scien-tific level. For us it is crucial that a brand can offer so optimum quality standards in all the areas of collaboration and at all the times and Mozo-Grau always complies at 100%”.
Dr. Daniel Torres LagaresDirector of Master in Oral Surgery Univer-sity of Seville, Dean of the Faculty of Den-tistry University of Seville. 20/08/2012
Quality
p. 5
CE Marking
COLOMBIA
TAIWAN
VENEZUELA
CHINARUSSIA
MEXICO
ISO 13485: 2012 ISO 9001: 2008
Introduction 3
Quality 4
The Perfect Fusion 7
Scientific Support 8
MG Vial manipulation 10
Código Explorer® 11
MG-INHEX Implants 13
3.30 MG-INHEX Implant 14
3.75 MG-INHEX Implant 15
4.25 MG-INHEX Implant 16
5.00 MG-INHEX Implant 17
MG-Inhex Prosthetic System 19
Prostheses scheme 20
Tools for prostheses and screwdrivers 25
MINI MG-INHEX Prosthetic System 26
STANDARD MG-INHEX Prosthetic System 28
MAXI MG-INHEX Prosthetic System 38
MG-INHEX Temporary prostheses/Immediate Loading 48
Screws for abutment and transfers 51
Surgical Material 53
Instructions for maintenance of surgical instruments 54
Surgical kits 55
Drills for implants 56
Drills for implants and RCD® stop kit 58
Surgical Wrenches 59
Bone Expansion 61
Accessories 62
MG-InHex® CatalogueIndex
Abut. Abutmentcc Cubic centimeterscm centimeterC/A Contra-Angle
Diff. Sit. Difficult SituationsH HeightImpr. Impressionmm Millimeters
Ncm Newtons per centimeterPrep. Prepableret. Retainingrpm Revolutions per minute
STD StandardTap. Taperedw/s With screw
Abbreviations
MG-INHEX
Imp
lant
sMG-INHEX
Pro
sthe
ses
SURGICAL
MATERIALS
p.
7
micron accuracy
With MG-InHex Implant, Mozo-Grau has achieved a solution
based on well established scientific results and respecting
surgical, biological and prosthetic principles thus ensuring a
very aesthetic result.
The ease of manipulation and the strength of the materials of the
MG-InHex implant allows the clinician to achieve predictable
aesthetic results with the security and reliability provided by its
high rate of success, based on solid osseointegration and ideal
distribution of the biomechanical loads.
The internal connection of MG-InHex implant is based on the
use of Morse Cone, which reliably ensures the correct stability
and solidity in the abutment, without loss of flexibility when
planning the restoration.
The location of the internal connection point between the
implant and the abutment, together with the design of the
microthreads in the coronal portion, respect the biological
principles that ensure a correct reaction from the perimplant
bone. On the other hand, the 45º shoulder has been proven
as the best solution in regard to the soft tissues treatment.
All these proven principles lead to the achievement of an
optimum aesthetic result.
The trunk and cone profile design of the implant allows
its walls to provide sufficient resistance to respond to
axial and paraxial occlusion loads with guarantees. The
Microthreads in the cortical part, which become threads
in the central part, together with the self-tapping design
of the apex end, make this implant one of the most stable
at insertion in the market. Moreover, the proven efficiency
of the RBM treated surface to achieve secondary or
biological stability, makes the MG-InHex Implant the best
option for immediate loading applications.
At Mozo-Grau we are very satisfied with the versatility
that the MG-InHex Implant offers and we are sure it will
meet the most demanding expectations of all the clinical
professionals and technicians in the sector.
the perfect fusion
MG-InHex®
Implantology. Implants. MG-InHex
p. 8
INTERNAL CONNECTION11º Morse taper double internal hexagon.
PLATFORM SWITCHINGRespect for the biological principles.
MICROTHREADSReducing marginal bone remodelation.
45º IMPLANT SHOULDERAesthetic soft tissues.
RBM SURFACE TREATMENTPredictable osseointegration. (Success rate 98,2%*)
SURFACE TREATMENT UP TO THE IMPLANT COLLAREvolution of science.
LOADING RESISTANCEStrength of material.
IMPLANT MORPHOLOGYSelf taping, conical apex and V-shape threads.
IMMEDIATE LOADINGSuitable for the treatment.
* According to the multicentric prospective study published in Official Journal of the Spanish Oral and Maxillofacial Surgery Association (published Sept-Oct 2009).1,475 implants placed, 654 prostheses over 480 patients, 2.5 years follow up.
Implantology. Implants. MG-InHex
List of Studies
MG-InHex®
p. 9
A solid base: over 50 scientific studies and articles
For more information about the scientific principles that support the MG-InHex implant design, please refer to, among others, the following scientific articles:
Microleakage of the prosthetic abutment/implant interface with internal and external connection: in vitro study
Carlos Larrucea Verdugo et al. University of Talca, Chile.
Publication: Clinical Oral Implant Research. Article first published online 4 July 2013
Conclusion: “.....the lower levels of microleakage occur in 30N tightened abutments, where, as shown in the photomicrographs, the gap is virtually nonexistent for Morse taper connections and external connections get an almost perfect seal. This may be due to the strict manufacturing criteria found in the analysed elements.”
Influence of implant neck design and implant-abut-ment connection type on peri-implant health. Ra-diological study
Miguel Peñarrocha Diago et al. University of Valencia, Spain.
Publication: Clinical Oral Implant Research. Vol. 24, Issue 11, pages 1192-1200, November 2013
Conclusion: “.....Global mean marginal bone loss with Osseous® was 0.27 ± 0.43 mm and 0.38 ± 0.51 mm as determined 6 and 12 months after prosthetic loading, respectively, whereas in the case of Inhex® was 0.07 ± 0.13 and 0.12 ± 0.17 mm..... Anyway, in both groups, the value obtained were within normal ranges described in the literature”
MG-InHex internal connection photomicrograph. Courtesy of Dr. Carlos Larrucea
Measurement of peri-implant marginal bone loss. Courtesy of Dr. Miguel Peñarrocha
Implantology. MG Vial manipulation
p. 10
MG Vial manipulation
PLACEMENT OF THE IMPLANT WITH THE CONTRA ANGLE
MANUAL PLACEMENT OF THE IMPLANT
Open the blister
Open the blister
Remove the vial
Remove the vial
Vial
Vial
Unscrew the plastic cap
Unscrew the plastic cap
Pick up the implant with the C/A
Place the cover screwPlace the implant in the alveolus Open the cap flip-top Extract the cover screw
Load the implant Place the implant in the alveolus*See the Hex. hand wrench on page 51
Remove the hand wrench Open the cap flip top Extract the cover screw Place the cover screw
Implantology. Código Explorer
p. 11
Your Implant, your CodeEvery Mozo Grau dental implant is identified with a Código Explorer®, a unique numeric code that will allow you to have full traceability and knowledge of your implant.
Código Explorer® ensures 100% traceability of every Mozo Grau implant leading to doctor’s and patient’s peace of mind. Enter your Código Explorer® in Mozo Grau website (www.mozo-grau.com) to download a Certificate of Quality showing full information about your implant.
Patients receive their Código Explorer® on a Mozo Grau Implant Card®, a very comfortable form to carry information everywhere.
I M P L A N T C A R D
Traceability as never seen before
MG-InHex®
Implants
Implants
Implantology. Implants. MG-InHex
DESCRIPTION
3.3 x 10 mm MINI MG-INHEX Implant
3.3 x 11.5 mm MINI MG-INHEX Implant
3.3 x 13 mm MINI MG-INHEX Implant
3.3 x 15 mm MINI MG-INHEX Implant
MG-INHEX MINI Cover screw*Do not tighten at torque values higher than 10 Ncm
DRILLING SEQUENCE
MG-INHEX
REF.
23203310
23203311
23203313
23203315
23203325
3.3 mm MINI MG-INHEX
- Double Internal Hexagon- R.B.M. Treated Surface- Implant Platform: 2.30 mm- Implant Diameter: 3.3 mm- Ø Internal thread: 1.4 mm- Internal Morse Cone 11º- Microthreads- Material: Grade V Titanium- Cover screw included in each implant- Implant mount included- “No touch” sterile package
A standard drilling sequence will be needed and the 3.0 mm drill will be the final one to be used
(recommended drilling speed: 800-1000 rpm). It is suggested to use the profile drill at 800 rpm. Being
the implant self-tapping, on very cortical bones (symphysis area) it is recommended to use the drills for
hard bones, and, if considered necessary, use the 3.3 mm bone tap to avoid overheating the bone and to
facilitate the implant insertion.
The use of copious internal irrigation is suggested, too.
It is recommended to place the implants at torque values between 35-45 Ncm.
Implant mount shows millimetermarks and hexagon position
Bone
Tap
(for v
ery
corti
cal
bone
s)
Loca
tor d
rill
800-1000 rpm 800-1000 rpm800 rpm 15 rpm
2.0
mm
3.0
mm
Profi
le D
rill
3.2
mm
har
d bo
ne d
rill
p. 14
p. 15
Implants
Implantology. Implants. MG-InHex
MG-INHEX
REF.
23203708
23203710
23203711
23203713
23203715
23205001
DESCRIPTION
3.75 x 8 mm STD MG-INHEX Implant
3.75 x 10 mm STD MG-INHEX Implant
3.75 x 11.5 mm STD MG-INHEX Implant
3.75 x 13 mm STD MG-INHEX Implant
3.75 x 15 mm STD MG-INHEX Implant
MG-INHEX STD Cover screw*Do not tighten at torque values higher than 10 Ncm
3.75 mm STANDARD MG-INHEX
- Double Internal Hexagon- R.B.M. Treated Surface- Implant Platform: 2.80 mm- Implant Diameter: 3.75 mm- Ø Internal thread: 1.6 mm- Internal Morse Cone 11º- Microthreads- Material: Grade IV Commercially Pure
Titanium- Cover screw included in each implant- Implant mount included- “No touch” sterile package
A standard drilling sequence will be needed and the 3.3 mm drill will be the final one to be used
(recommended drilling speed: 800-1000 rpm). It is suggested to use the profile drill at 800 rpm. Being
the implant self-tapping, on very cortical bones (symphysis area) it is recommended to use the drills for
hard bones, and, if considered necessary, use the 3.75 mm bone tap to avoid overheating the bone and
to facilitate the implant insertion.
The use of copious internal irrigation is suggested, too.
It is recommended to place the implants at torque values between 35-45 Ncm.
DRILLING SEQUENCE
Implant mount shows millimetermarks and hexagon position
Bone
Tap
(for v
ery
corti
cal
bone
s)
Loca
tor d
rill
2.0
mm
3.0
mm
3.3
mm
Profi
le D
rill
3.5
mm
har
d bo
ne d
rill
MG-INHEX
800-1000 rpm 800-1000 rpm800 rpm 15 rpm
p. 16
Implants
Implantology. Implants. MG-InHex
MG-INHEX4.25 mm STANDARD MG-INHEX
REF.
23204208
23204210
23204211
23204213
23204215
23205001
DESCRIPTION
4.25 x 8 mm STD MG-INHEX Implant
4.25 x 10 mm STD MG-INHEX Implant
4.25 x 11.5 mm STD MG-INHEX Implant
4.25 x 13 mm STD MG-INHEX Implant
4.25 x 15 mm STD MG-INHEX Implant
MG-INHEX STD Cover screw*Do not tighten at torque values higher than 10 Ncm
- Double internal hexagon- R.B.M. treated surface- Implant Platform: 2.80 mm- Implant Diameter: 4.25 mm- Ø Internal Thread: 1.6 mm- Internal Morse Cone 11º- Microthreads- Material: Grade IV Commercially Pure
Titanium- Cover screw included in each implant- Implant mount included- “No touch” sterile package
Recommendations for use:- Soft Bones (Type IV), Posterior Sectors
A standard drilling sequence will be needed and the 3.8 mm drill will be the final one to be used
(recommended drilling speed: 800-1000 rpm). It is suggested to use the profile drill at 800 rpm. Being
the implant self-tapping, on very cortical bones (symphysis area) it is recommended to use the drills for
hard bones, and, if considered necessary, use the 4.25 mm bone tap to avoid overheating the bone and
to facilitate the implant insertion.
The use of copious internal irrigation is suggested, too.
It is recommended to place the implants at torque values between 35-45 Ncm.
DRILLING SEQUENCE
Implant mount shows millimetermarks and hexagon position
Bone
Tap
(for v
ery
corti
cal
bone
s)
Loca
tor d
rill
2.0
mm
3.0
mm
3.3
mm
3.8
mm
Profi
le D
rill
4.0
mm
har
d bo
ne d
rill
800-1000 rpm 800-1000 rpm800 rpm 15 rpm
p. 17
MG-INHEX
REF.
23205009
23205010
23205011
23205013
23205015
23205000
DESCRIPTION
5.0 x 9 mm MAXI MG-INHEX Implant
5.0 x 10 mm MAXI MG-INHEX Implant
5.0 x 11.5 mm MAXI MG-INHEX Implant
5.0 x 13 mm MAXI MG-INHEX Implant
5.0 x 15 mm MAXI MG-INHEX Implant
MG-INHEX MAXI Cover screw*Do not tighten at torque values higher than 10 Ncm
- Double Internal Hexagon- R.B.M. Treated Surface- Implant Platform: 3.80 mm- Implant Diameter: 5.0 mm- Ø Internal Thread: 2.0 mm- Internal Morse Cone 11º- Microthreads- Material: Grade IV Commercially Pure
Titanium- Cover screw included on each implant- Implant mount included- “No touch” sterile package
Recommendations for use:- Soft Bones (Type IV), Posterior Sectors,
immediate post-extraction sites
5.0 mm MAXI MG-INHEX
A standard drilling sequence will be needed and the 4.7 mm drill will be the final one to be used
(recommended drilling speed: 800-1000 rpm). Drills wider than 4.3 mm are recommended to be used
at 400 rpm. It is suggested to use the profile drill at 800 rpm. Being the implant self-tapping, on very
cortical bones (symphysis area) it is recommended to use the drills for hard bones, and, if considered
necessary, use the 5.0 mm bone tap to avoid overheating the bone and to facilitate the implant insertion.
The use of copious internal irrigation is suggested, too.
It is recommended to place the implants at torque values between 35-45 Ncm.
DRILLING SEQUENCE
Implant mount shows millimetermarks and hexagon position
Bone
Tap
(for v
ery
corti
cal
bone
s)
Loca
tor d
rill
2.0
mm
3.0
mm
3.3
mm
3.8
mm
4.3
mm
4.7
mm
Profi
le D
rill
4.9
mm
har
d bo
ne d
rill
Implants
Implantology. Implants. MG-InHex
MG-INHEX
800-1000 rpm 400 rpm400 rpm 800 rpm 15 rpm
Discover this and other products in: www.mozo-grau.com
New MTA®
This new MTA line offers the easiest and most effective solution
The implant (MG InHex® o MG Osseous®) together with the MTA abutment with implant mount function allows the maximum use of all its prosthetic components with the high quality has always characterized Mozo-Grau
This new Line presents, together with a Mozo-Grau implant, a final MTA® abutment, an impression coping, a cover screw and a prosthetic screw, which makes it into the optimal solution to achieve the maximum efficiency of all its components.
MTA® FinalAbutment
MG InHex® Implant
MTA® ImpresionCoping
+
MG InHex® Implant
MTA® Final
+Cover Screw & Prosthetic Screw
+Cover Screw
+++C
M
Y
CM
MY
CY
CMY
K
MTA ENG2.pdf 1 01/10/15 09:49
Discover this and other products in: www.mozo-grau.com
New MTA®
This new MTA line offers the easiest and most effective solution
The implant (MG InHex® o MG Osseous®) together with the MTA abutment with implant mount function allows the maximum use of all its prosthetic components with the high quality has always characterized Mozo-Grau
This new Line presents, together with a Mozo-Grau implant, a final MTA® abutment, an impression coping, a cover screw and a prosthetic screw, which makes it into the optimal solution to achieve the maximum efficiency of all its components.
MTA® FinalAbutment
MG InHex® Implant
MTA® ImpresionCoping
+
MG InHex® Implant
MTA® Final
+Cover Screw & Prosthetic Screw
+Cover Screw
+++C
M
Y
CM
MY
CY
CMY
K
MTA ENG2.pdf 1 01/10/15 09:49
MG-InHex®
Prosthetic SystemProstheses schemeScrewdrivers and tipsHealing abutmentsImpression copingsDirect to implant abutmentsAbutment for ZirconiumBall and Locator® abutmentsTransmucosal (Tapered)Temporary Prostheses / Immediate LoadingScrews for Abutments and Transfers
p. 20
Healing abutment
AestheticHealing abutment
MINI Platform
STANDARD Platform
MAXI Platform
MG-INHEX Implants
Retaining Cap for Tapered Abutment
(10º-30º). 2 pcs.
Taperedabutment cap
Angled 17º
All the anti-rotational castable abutments are manufactured in red colour for an easy identification.*
UnitaryRestoration
Multiplerestoration (fixed) Direct to
implant
Transmucosal
Straight
Angled
Cemented
Cemented
Screw
Screw
Hex prepable abutment
Hex gold baseUCLA abutment
Hex / Non-Hexgold base
UCLA abutment
17º angledtapered abutment
10º Tapered abutment
30º Tapered abutment
Hex / Non-Hexgold base
UCLA abutment
Ball abutment Inhex
Locator® abutment(includes processing
pack)
Direct to implant
Ball abutment
Locator®
Bars
Overdenture(removable)
Non-Hexgold base
UCLA abutment
ABUTMENT FOR ZIRCONIUM
Straight
Angled 17º angledtapered abutment
10º Tapered abutment
30º Tapered abutment
Transmucosal
Direct to implant
Unitary
ImmediateTemporary Restoration
Multiple
Tapered abutment(10º - 30º)
Straight
Angled
Temporaryhex castable
UCLA abutment
Temporarynon hex castableUCLA abutment
Transmucosal
17º angledtapered abutment
Tapered Abutment Cap (10º-30º)
p. 21
Angled abutment(15º - 20º)
Hex / Non-Hexprepable abutment
Hex / Non-Hexprepable abutment
(weld with titanium)
Aesthetic hex prepable abutment
(weld with titanium)
Aesthetic hexprepable abutment
Hex titaniumUCLA abutment
(weld with titanium)
Abutment for Zirconium
Aesthetic hex prepable abutment
Angled abutment(15º - 20º)
Abutment for Zirconium
Castable post for 17º angled tapered
abutment
Titanium post for 17º angled tapered
abutment
Rotational castable post for tapered
abutment(10º - 30º)
Rotational titanium post for tapered
abutment(10º - 30º)
10º Anti-rotational castable post for
tapered abutment
10º Anti-rotational titanium post for tapered abutment
Plastic cap
10º Anti-rotational castable post for
tapered abutment
10º Anti-rotational titanium post for tapered abutment
Castable post for 17º angled tapered
abutment
Titanium post for 17º angled tapered
abutment
Rotational castable post for tapered
abutment(10º - 30º)
Rotational titanium post for tapered
abutment(10º - 30º)
Temporary prepable hex abutment
Temporary prepable non-hex abutment
Temporary castable post for tapered
abutment(10º - 30º)
Temporary titanium post for tapered
abutment(10º - 30º)
Temporarytitanium hex
UCLA abutment
Temporarytitanium non-hexUCLA abutment
Castable post for 17º angled tapered
abutment
Titanium post for 17º angled tapered
abutment
Bio-CAMMG
MG Bio-CAM®
Customized prosthesis
Mozo-Grau offers more:
QualityReliabilityPerfect adjustmentPeace of mindAccuracy
Now more connections available:Branemark type®; Straumann®; Nobel Replace®; Zimmer®; Astra Tech®...
Simply perfect
New!
p. 25
Prostheses. Prosthetic System MG-InHex
Prosthetic System MG-InHex®
100% of all the stages necessary for the production of the prosthesis for our implant system are subject to strict quality controls.
High precision machinery, with ±0.005 mm margin error and ±0.01 mm tolerance, is used to produce the prosthetic abutments.
Unless expressly specified in any section, the material used for producing the abutments is Grade V Titanium (TiAI6V
4)
REF.
13801500
14608020
14608030
14650185
DESCRIPTION
Dynamometrical manual wrench.Variable Tightening torque from 10 to 35 Ncm
20 Ncm torque wrench
30 Ncm torque wrench
Dynamometric ratchet wrench 45 Ncm.
TORQUE WRENCHES
- To assure the precise tightening of all the prosthetic screws
- For a bigger comfort when working in the posterior zone
Recommendations for use:- Tightening Torque:
· 30 Ncm for MG-InHex prostheses· 30 Ncm for MG-Osseous prostheses
SCREWDRIVERS AND TIPS
1.25 mm Hex Screwdriver- Used for: Cover screw, implant mount,
healing abutment, impression coping, tapered abutment, ball abutment, prosthetic screw, twist drills with stop
Screwdriver tip- 1.25 mm Hex Screwdriver- Used for: Cover screw, implant mount,
healing abutment, impression coping, tapered abutment, ball abutment, prosthetic screw, twist drills with stop
- Used with: ratchet wrench, torque wrench, hand wrench
REF.
15201125
15202125
15203125
15251125
15252125
15253125
14601125
14602125
14603125
13801525
13802525
13803125
19008393
DESCRIPTION
1.25 mm short Hex. Screwdriver. Length 8 mm
1.25 mm long Hex. Screwdriver Length 14 mm
14 mm flat screwdriver
1.25 mm short Hex. Dynamometric ratchet wrench. Length 8 mm. NEW
1.25 mm long Hex. Dynamometric ratchet wrench. Length 14 mm. NEW
14 mm flat screwdriver. Dynamometric ratchet wrench. NEW
1.25 mm short Hex. Screwdriver tip. Length 7 mm
1.25 mm long Hex. Screwdriver tip. Length 12 mm
12 mm flat screwdriver tip
1.25 mm short C/A Hex. Screwdriver. Length 9 mm
1.25 mm long C/A Hex. Screwdriver. Length 14 mm
14 mm C/A flat screwdriver
Locator® Core Tool
p. 26
Mini MG-InHex® Prosthetic System
Prostheses. Prosthetic System MG-InHex
MINI MG-INHEX
- Platform: 2.30 mm- Ø: 3.3 mm- Stainless Steel
Recommendations for use:- One single use
REF.
23205541
DESCRIPTION
Implant Analogue MG-INHEX MINI
MINI MG-INHEX IMPLANT ANALOG
MINI MG-INHEX
MINI MG-INHEX
REF.
23203320
23203330
23203340
DESCRIPTION
Healing abutment MG-INHEX MINI
Healing abutment MG-INHEX MINI
Healing abutment MG-INHEX MINI
CUFF HEIGHT (H)
2 mm
3 mm
4 mm
MINI MG-INHEX HEALING ABUTMENTS
MINI MG-INHEX IMPRESSION COPINGS
REF.
23203303
23235504
DESCRIPTION
Hex Impr. Coping w/s for MG-INHEX MINI
Short transfer screw MG-INHEX MINI
[ Hex
]
- Platform: 2.30 mm- Ø: 3.3 mm- Screwdriver: Hex 1.25 mm
Recommendations for use:- It is convenient to leave the cuff 2 mm
above the soft tissue- Maximum tightening torque 10 Ncm.
- Stainless Steel- Screwdriver: Hex 1.25 mm- Platform: 2.30 mm- Impression coping: L=13 mm , A=11 mm- Short transfer screw: L= 17 mm, A=9 mm- Ø: 3.3 mm
[ Hex ]- For single or multiple restorations- Used for open or closed tray
Recommendations for use:- For hex closed tray use short transfer screw- Maximum tightening torque 10 Ncm.
[ No Hex ]- For multiple restorations- Used for closed tray
Ø
H
Ø
AL
p. 27
DESCRIPTION
Hex Prep. Abutment w/s for MG-INHEX MINI
Hex Prep. Abutment w/s for MG-INHEX MINI
Hex Prep. Abutment w/s for MG-INHEX MINI
CUFF HEIGHT (H)
1 mm
2 mm
3 mm
Prostheses. Prosthetic System MG-InHex
Mini MG-InHex® Prosthetic System
MINI MG-INHEX
MINI MG-INHEX
REF.
23207031
23207032
23207033
MINI MG-INHEX HEX PREPABLE ABUTMENT
[ Hex
]
- Titanium Grade V abutment that can be cut- Attaches directly to implant- For single or multiple restorations- For cement retained restorations- Platform: 2.30 mm- Ø: 3.70 mm- Screwdriver: 1.25 mm Hex
Recommendations for use:- Soft tissue height must be above the
abutment ring height- Torque 30 Ncm.
* Abutments are also available without screw.
MINI MG-INHEX
REF.
23231015
23231020
DESCRIPTION
15º Angled prep. abut. w/s for MG-INHEX MINI
20º Angled prep. abut. w/s for MG-INHEX MINI
MINI MG-INHEX ANGLED PREPABLE ABUTMENT
CUFF HEIGHT (H)
2 mm
2 mm
[Hex
]
- Titanium Grade V abutment that can be cut - Attaches directly to implant- For single or multiple restorations- For cement retained restorations- Used to correct disparallelism- Platform: 2.30 mm- Ø: 3.7 mm- Screwdriver: 1.25 mm Hex.
Recommendations for use:- Soft tissue height must be above the
abutment ring height- Torque 30 Ncm
Ø
6,5 mm.
H
Ø
6,5 mm.
H
p. 28
Standard MG-InHex® Prosthetic System
Prostheses. Prosthetic System MG-InHex
STANDARD MG-INHEX
REF.
23204820
23204830
23204840
23204850
23204860
23204870
DESCRIPTION
Healing abutment MG-INHEX STD
Healing abutment MG-INHEX STD
Healing abutment MG-INHEX STD
Healing abutment MG-INHEX STD
Healing abutment MG-INHEX STD
Healing abutment MG-INHEX STD
CUFF HEIGHT (H)
2 mm
3 mm
4 mm
5 mm
6 mm
7 mm
STANDARD MG-INHEX HEALING ABUTMENTS
- Platform: 2.80 mm- Ø: 4.0 mm- Screwdriver: Hex 1.25 mm
Recommendations for use:- It is convenient to leave the cuff 2 mm
above the soft tissue- Maximum tightening torque 10 Ncm.
STANDARD MG-INHEX
REF.
23206030
23206040
23206050
23206060
23206070
DESCRIPTION
Aesthetic healing abutment for MG-INHEX STD
Aesthetic healing abutment for MG-INHEX STD
Aesthetic healing abutment for MG-INHEX STD
Aesthetic healing abutment for MG-INHEX STD
Aesthetic healing abutment for MG-INHEX STD
STANDARD MG-INHEX AESTHETIC HEALING ABUTMENTS
CUFF HEIGHT (H)
3 mm
4 mm
5 mm
6 mm
7 mm
- Platform: 2.80 mm- Ø: 6.0 mm- Screwdriver: Hex1.25 mm
Recommendation for use:- It is convenient to leave the cuff 2 mm
above the soft tissue- Maximum tightening torque 10 Ncm.
Ø
H
STANDARD MG-INHEX
REF.
23206036
23206046
23206056
23206066
23206076
DESCRIPTION
Healing abutment Ø5mm MG-INHEX STD
Healing abutment Ø5mm MG-INHEX STD
Healing abutment Ø5mm MG-INHEX STD
Healing abutment Ø5mm MG-INHEX STD
Healing abutment Ø5mm MG-INHEX STD
STANDARD MG-INHEX HEALING ABUTMENTS Ø5mm NEW
CUFF HEIGHT (H)
3 mm.
4 mm.
5 mm.
6 mm.
7 mm.
- Platform: 2.80 mm- Ø: 5.0 mm- Screwdriver: Hex 1.25 mm
Recommendations for use:- It is convenient to leave the cuff 2 mm
above the soft tissue- Maximum tightening torque 10 Ncm.
Ø
H
Ø
H
p. 29
Prostheses. Prosthetic System MG-InHex
Standard MG-InHex® Prosthetic System
STANDARD MG-INHEXSTANDARD MG-INHEX STANDARD MG-INHEX IMPRESSION COPINGS
REF.
23205503
23205506
23205403
23205600
23205603
23205606
DESCRIPTION
Hex Impr. Coping w/s for MG-INHEX STD
Aesthetic Hex Impr. Coping w/s for MG-INHEX STD
Long Hex Imp Coping w/s for MG-INHEX STD
Non-Hex Impr. Coping. for MG-INHEX STD
Aesthetic Non-Hex Impr. Coping for MG-INHEX STD
Long Non-Hex Impr. Coping for MG-INHEX STD
[ Hex
][ N
on H
ex ]
- Stainless Steel- Screwdriver: Hex 1.25 mm- Platform: 2.80 mm
[ Hex ]- For single or multiple restorations- Used for open or closed tray- Supplied with screw Ref. 23205502 (see page 43)- For hex closed tray use short transfer screw (Page
45, order separately)- Hex impression coping:
Ø: 4.1 mm L= 13.5 mm A=11 mm- Aesthetic Hex impression coping:
Ø: 6.0 mm L= 13.5 mm A=11 mm- Long Hex impression coping:
Ø: 4.1 mm L= 17 mm A=15 mm
[ Non Hex ]- For multiple restorations- For closed tray only- Non-hex impression coping:
Ø: 4.1 mm L=16.30 mm A=11 mm- Aesthetic non-hex impression coping:
Ø: 6.0 mm L=16.30 mm A=11 mm- Long non-hex impression coping:
Ø: 4.1 mm L=19.30 mm A=14 mmRecommendations for use:- Maximum tightening torque 10 Ncm.
STANDARD MG-INHEX
- Platform: 2.80 mm- Ø: 4.0 mm- Stainless Steel
Recommendations for use:- One single use
Analog wrenchTo hold the abutment or crown for a comfortable handling at lab or clinic
REF.
23205501
23285501
DESCRIPTION
Implant Analogue MG-INHEX STD
Analog wrench MG-INHEX STD
STANDARD MG-INHEX IMPLANT ANALOG
Ø
Ø
L
L
A
A
Standard MG-InHex® Prosthetic System
Prostheses. Prosthetic System MG-InHex
REF.
23207990
13207993
DESCRIPTION
Abutment for Zirconium w/s MG-INHEX STDIncludes one Sirona®’s CEREC 3D scanbody
Scanbodies (3 pcs each pack)* Compatible with Sirona®’s CEREC 3D
ABUTMENT FOR ZIRCONIUM
0,55
TITANIUM BASE FOR CAD/CAM. For production of customized mesostructures by CAD/CAM techniques
Mozo-Grau abutment for Zirconium allows the professional to carry out customized restorations using Zirconium over Mozo-Grau implants with the highest possible accuracy.
The abutment for Zirconium can be used as base to cement zirconium structures or mesostructures for unitary or multiple restoration cases, achieving the best possible passive adjustment that allows a safe, predictable and aesthetic result.
Mozo-Grau abutment for Zirconium can be scanned by some of the best scanners currently in the market allowing the use of modern software for infographic design.
STANDARD MG-INHEX
Ø
A= 10 mm
REF.
TITANIUM
23205245
23205345
GOLD
23209800
23209801
DESCRIPTION
Non-Hex Titanium UCLA w/s for MG-INHEX STD
Hex Titanium UCLA w/s for MG-INHEX STD
Hex GOLD BASE UCLA w/s for MG-INHEX STD(Gold 60/19)
Non-Hex GOLD BASE UCLA w/s for MG-INHEX STD(Gold 60/19)
STANDARD MG-INHEX UCLA ABUTMENT
- Hex Castable UCLA with Gold Base abutment- Attaches directly to implant- For cement retained or screw retained
restorations- Platform: 2.80 mm- Ø: 4.1 mm - Screwdriver: 1.25 mm Hex.- Cast using Gold alloys 60/19- Melting temperature 1415ºC
Recommendations for use:- Ensures a correct fit of the abutment to the
implant- Maximum tightening torque 20 Ncm.
- Titanium Grade V abutment- Attaches directly to implant- For cement retained or screw retained
restorations- Platform: 2.80 mm- Ø: 4.1 mm - Screwdriver: 1.25 mm Hex.
Recommendations for use:- Hex abutment is recommended for unitary
restorations- Maximum tightening torque 20 Ncm.- Ensures a correct fit of the abutment to the
implant
Ø
A= 10 mm
A= 2,7 mm
* Abutments are also available without screw.* Hex castable abutments are red-coloured for an easy identification.
p. 30
Prostheses. Prosthetic System MG-InHex
Standard MG-InHex® Prosthetic System
STANDARD MG-INHEX
p. 31
CUFF HEIGHT (H)
0 mm
1 mm
2 mm
3 mm
4 mm
STANDARD MG-INHEX
REF.
23207000
23207010
23207012
23207013
23207014
DESCRIPTION
Hex Prep. Abutment w/s for MG-INHEX STD
Hex Prep. Abutment w/s for MG-INHEX STD
Hex Prep. Abutment w/s for MG-INHEX STD
Hex Prep. Abutment w/s for MG-INHEX STD
Hex Prep. Abutment w/s for MG-INHEX STD
STANDARD MG-INHEX HEX PREPABLE ABUTMENT
[ Hex
]
- Titanium Grade V abutment that can be cut- Attaches directly to implant- For single or multiple restorations- For cement retained restorations- Platform: 2.80 mm- Ø: 4 mm- Screwdriver: 1.25 mm Hex
Recommendations for use:- Soft tissue height must be above the
abutment ring height- Torque 30 Ncm.
* Abutments are also available without screw.
STANDARD MG-INHEX
REF.
23207513
23207514
DESCRIPTION
Aesthetic Hex Prepable Abutment w/s for MG-INHEX STD
Aesthetic Hex Prepable Abutment w/s for MG-INHEX STD
CUFF HEIGHT (H)
3 mm
4 mm
STANDARD MG-INHEX AESTHETIC HEX PREPABLE ABUTMENT
- Titanium Grade V abutment that can be cut - Attaches directly to implant- For single or multiple restorations- For cement retained restorations- Platform: 2.80 mm- Ø: 6.0 mm- Screwdriver: 1.25 mm Hex.
Recommendations for use:- Soft tissue height must be above the
abutment ring height- Usable in situations of high aesthetic
compromise- Torque 30 Ncm.
* Abutments are also available without screw.
* Abutments are also available without screw.
[ Hex
]
Ø
6,5 mm.
H
STANDARD MG-INHEX
REF.
23207613
23207614
DESCRIPTION
Hex Prep. Abutment Ø5mm w/s for MG-INHEX STD
Hex Prep. Abutment Ø5mm w/s for MG-INHEX STD
STANDARD MG-INHEX HEX PREPABLE ABUTMENT Ø5mm NEW
- Titanium Grade V abutment that can be cut- Attaches directly to implant- For single or multiple restorations- For cement retained restorations- Platform: 2.80 mm- Ø: 5 mm- Screwdriver: 1.25 mm Hex
Recommendations for use:- Soft tissue height must be above the
abutment ring height- Torque 30 Ncm.
Ø
A= 6,5 mm.
H
[ Hex
] ALTURA (H)
3 mm.
4 mm.
Ø
A= 6,5 mm.
H
Ø
Ø
6,5 mm.
6,5 mm.
H
H
p. 32
Standard MG-InHex® Prosthetic System
Prostheses. Prosthetic System MG-InHex
CUFF HEIGHT (H)
1 mm
3 mm
5 mm
1 mm
3 mm
5 mm
REF.
23201015
23201315
23201515
23201020
23201320
23201520
DESCRIPTION
15º Angled prep. abut. w/s for MG-INHEX STD
15º Angled prep. abut. w/s for MG-INHEX STD
15º Angled prep. abut. w/s for MG-INHEX STD
20º Angled prep. abut. w/s for MG-INHEX STD
20º Angled prep. abut. w/s for MG-INHEX STD
20º Angled prep. abut. w/s for MG-INHEX STD
STANDARD MG-INHEX ANGLED PREPABLE ABUTMENT
[Hex
]
STANDARD MG-INHEX
- Titanium Grade V abutment that can be cut - Attaches directly to implant- For single or multiple restorations- For cement retained restorations- Used to correct disparallelism- Platform: 2.80 mm- Ø: 4.0 mm- Screwdriver: 1.25 mm Hex.
Recommendations for use:- Soft tissue height must be above the
abutment ring height- Torque 30 Ncm
CUFF HEIGHT (H)
1 mm
2 mm
3 mm
4 mm
1 mm
2 mm
3 mm
4 mm
STANDARD MG-INHEX
REF.
23207501
23207502
23207503
23207504
23207521
23207522
23207523
23207524
DESCRIPTION
Non-Hex Prep. Abutment for MG-INHEX STD
Non-Hex Prep. Abutment for MG-INHEX STD
Non-Hex Prep. Abutment for MG-INHEX STD
Non-Hex Prep. Abutment for MG-INHEX STD
Non-Hex Prep. Abut. w/s for MG-INHEX STD
Non-Hex Prep. Abut. w/s for MG-INHEX STD
Non-Hex Prep. Abut. w/s for MG-INHEX STD
Non-Hex Prep. Abut. w/s for MG-INHEX STD
STANDARD MG-INHEX NON-HEX PREPABLE ABUTMENT
- Titanium Grade V abutment that can be cut - Attaches directly to implant- For multiple restorations- For cement retained restorations- Platform: 2.80 mm- Ø: 4 mm- Screwdriver: 1.25 mm Hex
Recommendations for use:- Soft tissue height must be above the
abutment ring height- Torque 30 Ncm.
* Abutments are also available without screw.
[ Non
Hex
][ 2
pie
ces
]
Ø
6,5 mm.
H
STANDARD MG-INHEX
REF.
23206015
23206315
23206515
23206020
23206320
23206520
DESCRIPTION
15º Angled prep. abut. Ø5mm w/s for MG-INHEX STD
15º Angled prep. abut. Ø5mm w/s for MG-INHEX STD
15º Angled prep. abut. Ø5mm w/s for MG-INHEX STD
20º Angled prep. abut. Ø5mm w/s for MG-INHEX STD
20º Angled prep. abut. Ø5mm w/s for MG-INHEX STD
20º Angled prep. abut. Ø5mm w/s for MG-INHEX STD
STANDARD MG-INHEX ANGLED PREPABLE ABUTMENT Ø5mm NEW
CUFF HEIGHT (H)
1 mm.
3 mm.
5 mm.
1 mm.
3 mm.
5 mm.
[Hex
]
- Titanium Grade V abutment that can be cut - Attaches directly to implant- For single or multiple restorations- For cement retained restorations- Used to correct disparallelism - Platform: 2.80 mm- Ø: 5.0 mm- Screwdriver: 1.25 mm Hex.
Recommendations for use:- Soft tissue height must be above the
abutment ring height- Torque 30 Ncm
Ø
6,5 mm.
H
Ø
3 mm.
H
p. 33
Prostheses. Prosthetic System MG-InHex
Standard MG-InHex® Prosthetic System
CUFF HEIGHT (H)
1 mm
2 mm
3 mm
4 mm
5 mm
STANDARD MG-INHEX
REF.
19008530
232086810
232086820
232086830
232086840
232086850
19008505
19008028
19008589
DESCRIPTION
Locator® Analog - Pack 2 units
Locator® Abut.and processing package MG-INHEX STD
Locator® Abut.and processing package MG-INHEX STD
Locator® Abut.and processing package MG-INHEX STD
Locator® Abut.and processing package MG-INHEX STD
Locator® Abut.and processing package MG-INHEX STD
Locator® impression coping Pack 4 units.
Locator® bar attachment processing pack
Locator® bar attachment 2mm (2 pack)
STANDARD MG-INHEX LOCATOR® ABUTMENT
[ Non
Hex
] - For overdentures- Accommodates a divergent implant between
10 and 20 degrees (40 degrees between implants)
- Attaches directly to the implant- Platform: 2.80 mm- Ø: 4.0 mm- Use Locator® Core Tool- Torque 20 Ncm
Recommendations for use:- It is convenient to leave the Locator®
abutment at least 1 mm above the soft-tissue level
- The use of the Paralleling Guide will help to avoid problems when placing the abutments
* Males Clear=strong / Pink=light / Blue=Extralight
* Males for divergent implants Green=strong / Red=light
CUFF HEIGHT (H)
1 mm
2 mm
3 mm
4 mm
5.5 mm
STANDARD MG-INHEX
REF.
23208610
23208620
23208630
23208640
23208650
13205521
13208600
DESCRIPTION
Ball Abutment with Plastic cap for MG-INHEX STD
Ball Abutment with Plastic cap for MG-INHEX STD
Ball Abutment with Plastic cap for MG-INHEX STD
Ball Abutment with Plastic cap for MG-INHEX STD
Ball Abutment with Plastic cap for MG-INHEX STD
Ball Abutment Analog
(stainless steel)
Plastic Cap
STANDARD MG-INHEX BALL ABUTMENT
[ Non
Hex
] - For overdentures- Up to 10º relative divergence between implants- Attaches directly to the implant- Platform: 2.80 mm- Ø: 4.0 mm- Screwdriver: 1.25 mm Hex.- Stainless steel- Torque 30 Ncm
Recommendations for use:- It is convenient to leave the cuff 1 mm above
the soft tissue- The use of the Paralleling Guide will help to
avoid disparalellism problems when placing the ball abutments
5 mm
4 mm
STANDARD MG-INHEX
REF.
23202112
DESCRIPTION
Temporary. prepable. abutment. hex for chairside modif. for MG-INHEX STD
TEMPORARY PREPABLE ABUTMENT HEX FOR CHAIRSIDE MODIF. INHEX STD NEW
CUFF HEIGHT (H)
2 mm.
[Hex
] - Titanium Grade V abutment that can be cut - Attaches directly to implant- For cement retained restorations- Platform: 2.80 mm- Ø: 5.0 mm- Screwdriver: 1.25 mm Hex.
Recommendations for use:- Soft tissue height must be above the abutment
ring height- Torque 30 Ncm
Ø
11 mm.
p. 34
Standard MG-InHex® Prosthetic System
Prostheses. Prosthetic System MG-InHex
STANDARD MG-INHEXSTANDARD MG-INHEX TAPERED ABUTMENT
REF.
23201000
23201001
23201002
23201003
23201004
23201005
23203001
23203002
23203003
23203004
23203005
DESCRIPTION
10º tapered abutment MG-INHEX STD
10º tapered abutment MG-INHEX STD
10º tapered abutment MG-INHEX STD
10º tapered abutment MG-INHEX STD
10º tapered abutment MG-INHEX STD
10º tapered abutment MG-INHEX STD
30º tapered abutment MG-INHEX STD
30º tapered abutment MG-INHEX STD
30º tapered abutment MG-INHEX STD
30º tapered abutment MG-INHEX STD
30º tapered abutment MG-INHEX STD
CUFF HEIGHT (H)
0 mm
1 mm
2 mm
3 mm
4 mm
5 mm
1 mm
2 mm
3 mm
4 mm
5 mm
- For multiple restorations- For overdentures or superstructures- Screw-retained- The 10º or 30ºangle corrects disparallelism- Attaches directly to the implant- Platform: 2.80 mm- Ø: 4.0 mm- Screwdriver: 1.25 mm Hex.
Recommendations for use:- For restorations in soft tissues thicker than
3 mm- To take impressions is recommendable to
use tapered abutments Impression Copings- Torque 30 Ncm.
Transmucosal tapered abutmentfor screw retained restorations
Recommended for immediate loading and compromised cases with damaged periodontal tissues.
Eases the exchange of provisional abutments during the immediate loading protocol.
Improves the emergency profile and maintains the gingival and osseous level.
Avoids the contact of the temporary abutments and impression copings with the wound.Protects the hard and soft perimplantary tissues and eases the prosthetics hygiene.
Flat side that provides an anti-rotational system to the abutment.
Ø
0,75 mm.
H
Ø
2 mm.
H
p. 35
Prostheses. Prosthetic System MG-InHex
Standard MG-InHex® Prosthetic System
STANDARD MG-INHEX
Ø
11 mm
STANDARD MG-INHEXSTANDARD MG-INHEX TAPERED ABUTMENTS
REF.
13209152
13209151
13209153
13209252
13209251
13209253
13205511
13203511
13205213
13205513 / 30
13205613 / 30
13201000
13201300
23201720
23201730
23201740
13201751
13209117
13205117
13205217
13201017
DESCRIPTION
10º anti-rotational castable post for tapered abut. w/s
10º rotational castable post for tapered abut. w/s
30º rotational castable post for tapered abut. w/s
10º anti-rotational titanium post for tapered abut. w/s
10º rotational titanium post for tapered abut. w/s
30º rotational titanium post for tapered abut. w/s
10º tapered abutment analog
30º tapered abutment analog
10º anti-rotational impression coping for tapered abut. w/s
10º / 30º rotational impr. coping for tapered abut. w/s
10º / 30º impression coping for tap. abut. closed tray
10º tapered abutment cap (1 piece)
30º tapered abutment cap (1 piece)
17º angled tapered abutment MG-INHEX STD 2 mm height
17º angled tapered abutment MG-INHEX STD 3 mm height
17º angled tapered abutment MG-INHEX STD 4 mm height
Rotational castable post for 17º angled tapered abutment w/s
Rotational titanium post for 17º angled tapered abutment w/s
Rotational 17º angled tapered abutment analog
Rotational impression coping for 17º angledtapered abutment w/s
17º tapered abutment cap
Ø
11 mm
Ø
11 mm
Ø
4,2 mm
- Material: stainless steel
- Material: stainless steel
- Material: stainless steel
- Grade V Titanium.
- Grade V Titanium.
- Castable abutment.- Torque 20 Ncm.
* Anti-rotational castable abutments are manufactured in red colour for an easy identification.
- Castable abutment.- Torque 20 Ncm.
- Grade V Titanium.- Torque 20 Ncm.
- Grade V Titanium.- Torque 30 Ncm.
Recommendations for use:- Used to correct disparalellism between
implants.- Used to restore implants with very
divergent emergency angles.
- Grade V Titanium.- Torque 20 Ncm.
* Anti-rotational titanium abutments are manufactured in purple colour for an easy identification.
* Anti-rotational abutments are manufactured in purple colour for an easy identification.
p. 36
Standard MG-InHex® Prosthetic System
Prostheses. Prosthetic System MG-InHex
STANDARD MG-INHEXSTANDARD MG-INHEX MORSE TAPER TAPERED ABUTMENT NEW
DESCRIPTION
10º Morse taper tapered abutment MG-INHEX STD
10º Morse taper tapered abutment MG-INHEX STD
10º Morse taper tapered abutment MG-INHEX STD
10º Morse taper tapered abutment MG-INHEX STD
10º Morse taper tapered abutment MG-INHEX STD
10º Morse taper tapered abutment MG-INHEX STD
30º Morse taper tapered abutment MG-INHEX STD
30º Morse taper tapered abutment MG-INHEX STD
30º Morse taper tapered abutment MG-INHEX STD
30º Morse taper tapered abutment MG-INHEX STD
30º Morse taper tapered abutment MG-INHEX STD
- For multiple restorations- For overdentures or superstructures- Screw-retained- The 10º or 30ºangle corrects disparallelism- Attaches directly to the implant- Platform: 2.80 mm- Ø: 4.0 mm- Screwdriver: 1.25 mm Hex.
Recommendations for use:- For restorations in soft tissues thicker than
3 mm- To take impressions is recommendable to
use tapered abutments Impression Copings- Torque 30 Ncm.
Transmucosal tapered abutmentfor screw retained restorations
Recommended for immediate loading and compromised cases with damaged periodontal tissues.
Eases the exchange of provisional abutments during the immediate loading protocol.
Improves the emergency profile and maintains the gingival and osseous level.
Avoids the contact of the temporary abutments and impression copings with the wound.Protects the hard and soft perimplantary tissues and eases the prosthetics hygiene.
Ø
0,75 mm.
H
Ø
2 mm.
H
CUFF HEIGHT (H)
0 mm
1 mm
2 mm
3 mm
4 mm
5 mm
1 mm
2 mm
3 mm
4 mm
5 mm
REF.
23201600
23201601
23201602
23201603
23201604
23201605
23203601
23203602
23203603
23203604
23203605
p. 37
Prostheses. Prosthetic System MG-InHex
Standard MG-InHex® Prosthetic System
STANDARD MG-INHEX
Ø
11 mm.
STANDARD MG-INHEXSTANDARD MG-INHEX MORSE TAPER TAPERED ABUTMENTS NEW
REF.
13209162
13209161
13209163
13209262
13209261
13209263
13205561
13203561
13205260
13205560 / 63
13205660 / 63
13201060
13201360
DESCRIPTION
10º anti-rotational cast. post for morse taper tapered abut. w/s
10º rotational castable post for morse taper tapered abut. w/s
30º rotational castable post for morse taper tapered abut. w/s
10º anti-rotational titan. post for morse taper tapered abut. w/s
10º rotational titanium post for morse taper tapered abut. w/s
30º rotational titanium post for morse taper tapered abut. w/s
10º morse taper tapered abutment analog
30º morse taper tapered abutment analog
10º anti-rot. impr. coping for morse taper tapered abut. w/s
10º / 30º rot. impr. coping for morse taper tapered abut. w/s
10º / 30º impr. coping for morse taper tap. abut. closed tray
10º morse taper tapered abutment cap (1 piece)
30º morse taper tapered abutment cap (1 piece)
- Material: stainless steel
- Castable abutment.- Torque 20 Ncm.
*Anti-rotational castable abutments are manufactured in red colour for an easy identification.
Ø
11 mm.
Ø
11 mm.
Ø
4,2 mm.
- Grade V Titanium. - Torque 20 Ncm.
*Anti-rotational titanium abutments are manufactured in purple colour for an easy identification.
- Grade V Titanium.
* Anti-rotational abutments are manufactured in purple colour for an easy identification.
p. 38
Maxi MG-InHex® Prosthetic System
Prostheses. Prosthetic System MG-InHex
CUFF HEIGHT (H)
3 mm
4 mm
5 mm
6 mm
7 mm
MAXI MG-INHEX
MAXI MG-INHEX
CUFF HEIGHT (H)
2 mm
3 mm
4 mm
5 mm
6 mm
7 mm
MAXI MG-INHEX HEALING ABUTMENTS
REF.
23205020
23205030
23205040
23205050
23205060
23205070
DESCRIPTION
Healing abutment MG-INHEX MAXI
Healing abutment MG-INHEX MAXI
Healing abutment MG-INHEX MAXI
Healing abutment MG-INHEX MAXI
Healing abutment MG-INHEX MAXI
Healing abutment MG-INHEX MAXI
MAXI MG-INHEX AESTHETIC HEALING ABUTMENTS
REF.
23206530
23206540
23206550
23206560
23206570
DESCRIPTION
Aesthetic healing abutment for MG-INHEX MAXI
Aesthetic healing abutment for MG-INHEX MAXI
Aesthetic healing abutment for MG-INHEX MAXI
Aesthetic healing abutment for MG-INHEX MAXI
Aesthetic healing abutment for MG-INHEX MAXI
- Platform: 3.80 mm- Ø: 4.0 mm- Screwdriver: Hex. 1.25 mm
Recommendations for use:- It is convenient to leave the cuff 1 mm
above the soft tissue- Maximum tightening torque 10 Ncm.
- Platform: 3.80 mm- Ø: 6.0 mm- Screwdriver: Hex. 1.25 mm
Recommendation for use:- It is convenient to leave 1 mm of the cuff
above the soft tissue- Maximum tightening torque 10 Ncm.
Ø
H
MAXI MG-INHEX
CUFF HEIGHT (H)
3 mm.
4 mm.
5 mm.
6 mm.
7 mm.
MAXI MG-INHEX HEALING ABUTMENTS Ø5mm. NEW
REF.
23206536
23206546
23206556
23206566
23206576
DESCRIPTION
Healing abutment Ø5mm MG-INHEX MAXI
Healing abutment Ø5mm MG-INHEX MAXI
Healing abutment Ø5mm MG-INHEX MAXI
Healing abutment Ø5mm MG-INHEX MAXI
Healing abutment Ø5mm MG-INHEX MAXI
- Platform: 3.80 mm- Ø: 5.0 mm- Screwdriver: Hex. 1.25 mm
Recommendations for use:- It is convenient to leave the cuff 1 mm
above the soft tissue- Maximum tightening torque 10 Ncm.
Ø
H
Ø
H
p. 39
Prostheses. Prosthetic System MG-InHex
Maxi MG-InHex® Prosthetic System
MAXI MG-INHEX
REF.
23205003
23255403
23205006
23205056
23205306
23205066
DESCRIPTION
Hex Impr. Coping for MG-INHEX MAXI
Aesthetic Hex Impr. Coping for MG-INHEX MAXI
Long Hex Imp Coping for MG-INHEX MAXI
Non-Hex Impr. Coping for MG-INHEX MAXI
Aesthetic Non-Hex Impr. Coping for MG-INHEX MAXI
Long Non-Hex Impr. Coping for MG-INHEX MAXI
MAXI MG-INHEX IMPRESSION COPINGS
[ Hex
][ N
on H
ex ]
- Stainless Steel- Screwdriver: Hex 1.25 mm- Platform: 3.80 mm
[ Hex ]- For single or multiple restorations- Used for open or closed tray- Supplied with screw Ref. 23205002 (see page 43)- For hex closed tray use short transfer screw (Page
45, order separately)- Hex impression coping:
Ø: 4.1 mm L= 15 mm A=11 mm- Aesthetic Hex impression coping:
Ø: 6.0 mm L= 15 mm A=11 mm- Long Hex impression coping:
Ø: 4.1 mm L= 18.5 mm A=15 mm
[ Non Hex ]- For multiple restorations- For closed tray only- Non-hex impression coping:
Ø: 4.1 mm L=18.50 mm A=11 mm- Aesthetic non-hex impression coping:
Ø: 6.0 mm L=18.50 mm A=11 mm- Long non-hex impression coping:
Ø: 4.1 mm L=21.50 mm A=14 mm
Recommendations for use:- Maximum tightening torque 10 Ncm.
MAXI MG-INHEX
REF.
23205605
23285605
DESCRIPTION
Implant Analog MG-INHEX MAXI
Analog wrench MG-INHEX MAXI
MAXI MG-INHEX IMPLANT ANALOG
- Stainless Steel- Platform: 3.80 mm- Ø: 5.00 mm
Recommendations for use:- One single use
Analog wrenchTo hold the abutment or crown for a comfortable handling at lab or clinic
MAXI MG-INHEX
Ø
A
Ø
AL
L
p. 40
Maxi MG-InHex® Prosthetic System
Prostheses. Prosthetic System MG-InHex
MAXI MG-INHEX
REF.
TITANIUM
23205255
23205355
GOLD
23209850
23209851
DESCRIPTION
Non-Hex Titanium UCLA w/s for MG-INHEX MAXI
Hex Titanium UCLA w/s MG-INHEX MAXI
Hex GOLD BASE UCLA w/s for MG-INHEX MAXI(Gold 60/19)
Non-Hex GOLD BASE UCLA w/s for MG-INHEX MAXI(Gold 60/19)
MAXI MG-INHEX TITANIUM UCLA
- Castable UCLA with Gold Base abutment- Attaches directly to implant- Platform: 3.80 mm- Ø: 4 mm- Screwdriver: 1.25 mm Hex.- Cast with 60/19 Gold alloys.- Melting temperature 1415ºC
Recommendations for use:- Recommended Torque 30 Ncm.- Ensures a correct fit of the abutment to
the implant
- Titanium Grade V abutment- Attaches directly to implant- For cement retained or screwretained
restorations- Platform: 3.80 mm- Ø: 4 mm- Screwdriver: 1.25 mm Hex.
Recommendations for use:- Hex abutment is recommended for unitary
restorations- Recommended Torque 30 Ncm.- Ensures a correct fit of the abutment to
the implant
Ø
A= 10 mm
* Abutments are also available without screw.* Hex castable abutments are red-coloured for an easy identification.
REF.
23257990
13207993
DESCRIPTION
Abutment for Zirconium w/s MG-INHEX MAXI Includes one Sirona®’s CEREC 3D scanbody
Scanbodies (3 pcs each pack)* Compatible with Sirona®’s CEREC 3D
ABUTMENT FOR ZIRCONIUM
0,55
TITANIUM BASE FOR CAD/CAM. For production of customized mesostructures by CAD/CAM techniques
Mozo-Grau abutment for Zirconium allows the professional to carry out customized restorations using Zirconium over Mozo-Grau implants with the highest possible accuracy.
The abutment for Zirconium can be used as base to cement zirconium structures or mesostructures for unitary or multiple restoration cases, achieving the best possible passive adjustment that allows a safe, predictable and aesthetic result.
Mozo-Grau abutment for Zirconium can be scanned by some of the best scanners currently in the market allowing the use of modern software for infographic design.
Ø
A= 10 mm
A= 2,7 mm
p. 41
Prostheses. Prosthetic System MG-InHex
Maxi MG-InHex® Prosthetic System
MAXI MG-INHEX
REF.
23207050
23207051
23207052
23207053
23207054
DESCRIPTION
Hex Prep. Abut. w/s for MG-INHEX MAXI
Hex Prep. Abut. w/s for MG-INHEX MAXI
Hex Prep. Abut. w/s for MG-INHEX MAXI
Hex Prep. Abut. w/s for MG-INHEX MAXI
Hex Prep. Abut. w/s for MG-INHEX MAXI
CUFF HEIGHT (H)
0 mm
1 mm
2 mm
3 mm
4 mm
MAXI MG-INHEX HEX PREPABLE ABUTMENT
- Titanium Grade V- Attaches directly to implant- For cement retained or screwretained
restorations- Platform: 3.80 mm- Ø: 4.1 mm- Screwdriver: 1.25 mm Hex.
Recommendations for use:- Hex abutment is recommended for unitary
restorations- Torque 30 Ncm.
Ø
6,5 mm
H
* Abutments are also available without screw.
* Abutments are also available without screw.
[ Hex
]
MAXI MG-INHEX
DESCRIPTION
Hex Prep. Abutment Ø5mm w/s for MG-INHEX MAXI
Hex Prep. Abutment Ø5mm w/s for MG-INHEX MAXI
CUFF HEIGHT (H)
3 mm.
4 mm.
- Titanium Grade V- Attaches directly to implant- For cement retained or screwretained
restorations- Platform: 3.80 mm- Ø: 5 mm- Screwdriver: 1.25 mm Hex.
Recommendations for use:- Hex abutment is recommended for unitary
restorations- Torque 30 Ncm.
MAXI MG-INHEX HEX PREPABLE ABUTMENT Ø5mm. NEW
REF.
23257613
23257614
[ Hex
]
Ø
6,5 mm.
H
CUFF HEIGHT (H)
1 mm
2 mm
3 mm
4 mm
1 mm
2 mm
3 mm
4 mm
MAXI MG-INHEX
REF.
23257501
23257502
23257503
23257504
23257521
23257522
23257523
23257524
DESCRIPTION
Non-Hex Prep. Abut. for MG-INHEX MAXI
Non-Hex Prep. Abut. for MG-INHEX MAXI
Non-Hex Prep. Abut. for MG-INHEX MAXI
Non-Hex Prep. Abut. for MG-INHEX MAXI
Non-Hex Prep. Abut. w/s for MG-INHEX MAXI
Non-Hex Prep. Abut. w/s for MG-INHEX MAXI
Non-Hex Prep. Abut. w/s for MG-INHEX MAXI
Non-Hex Prep. Abut. w/s for MG-INHEX MAXI
MAXI MG-INHEX NON-HEX PREPABLE ABUTMENT
- Titanium Grade V abutment for chair side modification
- Attaches directly to implant- For multiple restorations- For cement retained restorations.- Platform: 3.80 mm- Ø: 4.1 mm- Screwdriver: 1.25 mm Hex.
Recommendations for use:- Soft tissue height must be above the
abutment ring height- Torque 30 Ncm.
Ø
Ø
6,5 mm
6,5 mm
H
H
* Abutments are also available without screw.
[ Non
Hex
][ 2
pie
ces
]
CUFF HEIGHT (H)
1 mm.
3 mm.
5 mm.
1 mm.
3 mm.
5 mm.
p. 42
MAXI MG-INHEX
DESCRIPTION
Aest. Hex Prep. Abut. w/s for MG-INHEX MAXI
Aest. Hex Prep. Abut. w/s for MG-INHEX MAXI
CUFF HEIGHT (H)
3 mm
4 mm
- Titanium Grade V post for chair side modification
- Attaches directly to implant- For single or multiple restorations- For cement retained restorations- Platform: 3.80 mm- Ø: 6.0 mm- Screwdriver: 1.25 mm Hex
Recommendations for use:- Soft tissue height must be above the
abutment ring height- Usable in situations of high aesthetic
compromise- Torque 30 Ncm.
MAXI MG-INHEX AESTHETIC HEX PREPABLE ABUTMENT
REF.
23257513
23257514
* Abutments are also available without screw.
MAXI MG-INHEX
REF.
23251015
23251315
23251515
23251020
23251320
23251520
DESCRIPTION
15º Angled prep. abut. w/s for MG-INHEX MAXI
15º Angled prep. abut. w/s for MG-INHEX MAXI
15º Angled prep. abut. w/s for MG-INHEX MAXI
20º Angled prep. abut. w/s for MG-INHEX MAXI
20º Angled prep. abut. w/s for MG-INHEX MAXI
20º Angled prep. abut. w/s for MG-INHEX MAXI
MAXI MG-INHEX ANGLED PREPABLE ABUTMENT
CUFF HEIGHT (H)
1 mm
3 mm
5 mm
1 mm
3 mm
5 mm
- Titanium Grade V abutment for chair side modification
- Attaches directly to implant- For single or multiple restorations- For cement retained restorations- Used to correct disparallelism- Platform: 3.80 mm- Ø: 4.0 mm- Screwdriver: 1.25 mm Hex
Recommendations for use:- Soft tissue height must be above the
abutment ring height- Torque 30 Ncm.
[ Hex
][ H
ex ]
Maxi MG-InHex® Prosthetic System
Prostheses. Prosthetic System MG-InHex
Ø
6,5 mm.
H
Ø
6,5 mm
H
MAXI MG-INHEX
REF.
23256015
23256315
23256515
23256020
23256320
23256520
DESCRIPTION
15º Angled prep. abut. Ø5mm w/s for MG-INHEX MAXI
15º Angled prep. abut. Ø5mm w/s for MG-INHEX MAXI
15º Angled prep. abut. Ø5mm w/s for MG-INHEX MAXI
20º Angled prep. abut. Ø5mm w/s for MG-INHEX MAXI
20º Angled prep. abut. Ø5mm w/s for MG-INHEX MAXI
20º Angled prep. abut. Ø5mm w/s for MG-INHEX MAXI
MAXI MG-INHEX ANGLED PREPABLE ABUTMENT Ø5MM NEW
- Titanium Grade V abutment for chair side modification
- Attaches directly to implant- For single or multiple restorations - For cement retained restorations - Used to correct disparallelism- Platform: 3.80 mm- Ø: 5.0 mm- Screwdriver: 1.25 mm Hex
Recommendations for use:- Soft tissue height must be above the
abutment ring height- Torque 30 Ncm.
[ Hex
]
Ø
6,5 mm
H
p. 43
CUFF HEIGHT (H)
0.73 mm
2 mm
3 mm
4 mm
5 mm
MAXI MG-INHEX
REF.
19008530
232586810
232586820
232586830
232586840
232586850
19008505
19008028
19008589
DESCRIPTION
Locator Analog pack 2 pcs.
Locator® Abut. and processing package MG-INHEX MAXI
Locator® Abut. and processing package MG-INHEX MAXI
Locator® Abut. and processing package MG-INHEX MAXI
Locator® Abut. and processing package MG-INHEX MAXI
Locator® Abut. and processing package MG-INHEX MAXI
Locator® impression coping Pack 4 units.
Locator® bar attachment processing pack
Locator® bar attachment 2mm (2 pack)
MAXI MG-INHEX LOCATOR® ABUTMENT
- For overdentures- Accommodates a divergent implant
between 10 and 20 degrees (40 degrees between implants)
- Attaches directly to the implant- Platform: 2.80 mm- Ø: 4.0 mm- Use Locator® Core Tool- Torque 20 Ncm
Recommendations for use:- It is convenient to leave the Locator®
abutment at least 1 mm above the soft-tissue level
- The use of the Paralleling Guide will help to avoid problems when placing the abutments
* Males Clear=strong / Pink=light / Blue=Extralight
* Males for divergent implants Green=strong / Red=light
[ Non
Hex
]
Prostheses. Prosthetic System MG-InHex
Maxi MG-InHex® Prosthetic System
MAXI MG-INHEX
REF.
23258610
23258620
23258630
23258640
23258655
13205521
13208600
DESCRIPTION
Ball Abut. with Plastic cap for MG-INHEX MAXI
Ball Abut. with Plastic cap for MG-INHEX MAXI
Ball Abut. with Plastic cap for MG-INHEX MAXI
Ball Abut. with Plastic cap for MG-INHEX MAXI
Ball Abut. with Plastic cap for MG-INHEX MAXI
Ball Abutlment Analog
(stainless steel)
Plastic Cap
MAXI MG-INHEX BALL ABUTMENT
CUFF HEIGHT (H)
1 mm
2 mm
3 mm
4 mm
5.5 mm
- For overdentures- Maximum angle of 10º- Attaches directly to the implant- Platform: 3.80 mm- Ø: 4.0 mm- Screwdriver: 1.25 mm Hex.- Stainless steel- Torque 30 Ncm
Recommendations for use:- It is convenient to leave the cuff 1 mm
above the soft tissue- The use of the Paralleling Guide will help to
avoid disparalellism problems when placing the ball abutments
Ø
3 mm
H
5 mm
4 mm
[ Non
Hex
]
p. 44
MAXI MG-INHEXMAXI MG-INHEX TAPERED ABUTMENTS
REF.
23201050
23201051
23201052
23201053
23201054
23201055
23253001
23253002
23253003
23253004
23253005
DESCRIPTION
10º tapered abutment MG-INHEX MAXI
10º tapered abutment MG-INHEX MAXI
10º tapered abutment MG-INHEX MAXI
10º tapered abutment MG-INHEX MAXI
10º tapered abutment MG-INHEX MAXI
10º tapered abutment MG-INHEX MAXI
30º tapered abutment MG-INHEX MAXI
30º tapered abutment MG-INHEX MAXI
30º tapered abutment MG-INHEX MAXI
30º tapered abutment MG-INHEX MAXI
30º tapered abutment MG-INHEX MAXI
CUFF HEIGHT (H)
0 mm
1 mm
2 mm
3 mm
4 mm
5 mm
1 mm
2 mm
3 mm
4 mm
5 mm
- For multiple restorations- For overdentures or superstructures- For screw-retained restorations- The10º or 30º angle corrects disparallelism- Attaches directly to the implant- Platform: 3.80 mm- Ø: 4.0 mm- Screwdriver: 1.25 mm Hex.
Recommendations for use:- For restorations in soft tissues thicker than
3 mm- To take impressions is recommendable to
use tapered abutments impression copings- Torque 30 Ncm.
Flat side that provides an anti-rotational system to the abutment.
Maxi MG-InHex® Prosthetic System
Prostheses. Prosthetic System MG-InHex
Transmucosal tapered abutmentfor screw retained restorations
Recommended for immediate loading and compromised cases with damaged periodontal tissues.
Eases the exchange of provisional abutments during the immediate loading protocol.
Improves the emergency profile and maintains the gingival and osseous level.
Avoids the contact of the temporary abutments and impression copings with the wound.Protects the hard and soft perimplantary tissues and eases the prosthetics hygiene.
Ø
2 mm
H
Ø
0,75 mm
H
p. 45
Ø
11 mm
MAXI MG-INHEXMAXI MG-INHEX TAPERED ABUTMENTS
REF.
13209152
13209151
13209153
13209252
13209251
13209253
13205511
13203511
13205213
13205513 / 30
13205613 / 30
13201000
13201300
23251720
23251730
23251740
13201751
13209117
13205117
13205217
13201017
DESCRIPTION
10º anti-rotational castable post for tapered abut. w/s
10º rotational castable post for tapered abut. w/s
30º rotational castable post for tapered abut. w/s
10º anti-rotational titanium post for tapered abut. w/s
10º rotational titanium post for tapered abut. w/s
30º rotational titanium post for tapered abut. w/s
10º tapered abutment analog
30º tapered abutment analog
10º anti-rotational impression coping for tapered abut. w/s
10º / 30º rotational impr. coping for tapered abut. w/s
10º / 30º impression coping for tap. abut. closed tray
10º tapered abutment cap (1 piece)
30º tapered abutment cap (1 piece)
17º angled tapered abutment MG-INHEX MAXI 2 mm height
17º angled tapered abutment MG-INHEX MAXI 3 mm height
17º angled tapered abutment MG-INHEX MAXI 4 mm height
Rotational castable post for 17º angled tapered abutment w/s
Rotational titanium post for 17º angled tapered abutment w/s
Rotational 17º angled tapered abutment analog w/s
Rotational impression coping for 17º angledtapered abutment w/s
17º tapered abutment cap
Ø
11 mm
Ø
11 mm
Ø
4,2 mm
Prostheses. Prosthetic System MG-InHex
Maxi MG-InHex® Prosthetic System
- Material: stainless steel
- Material: stainless steel
- Castable abutment.- Torque 20 Ncm.
* Anti-rotational castable abutments are manufactured in red colour for an easy identification.
- Castable abutment.- Torque 20 Ncm.
- Grade V Titanium.- Torque 20 Ncm.
- Grade V Titanium.- Torque 30 Ncm.
Recommendations for use:- Used to correct disparalellism between
implants.- Used to restore implants with very
divergent emergency angles.
- Grade V Titanium.- Torque 20 Ncm.
* Anti-rotational titanium abutments are manufactured in purple colour for an easy identification.
* Anti-rotational abutments are manufactured in purple colour for an easy identification.
- Material: stainless steel
- Grade V Titanium.
- Grade V Titanium.
p. 46
Maxi MG-InHex® Prosthetic System
Prostheses. Prosthetic System MG-InHex
Transmucosal tapered abutmentfor screw retained restorations
Recommended for immediate loading and compromised cases with damaged periodontal tissues.
Eases the exchange of provisional abutments during the immediate loading protocol.
Improves the emergency profile and maintains the gingival and osseous level.
Avoids the contact of the temporary abutments and impression copings with the wound.Protects the hard and soft perimplantary tissues and eases the prosthetics hygiene.
MAXI MG-INHEX
- For multiple restorations- For overdentures or superstructures- For screw-retained restorations- The10º or 30º angle corrects disparallelism- Attaches directly to the implant- Platform: 3.80 mm- Ø: 4.0 mm- Screwdriver: 1.25 mm Hex.
Recommendations for use:- For restorations in soft tissues thicker than
3 mm- To take impressions is recommendable to
use tapered abutments impression copings- Torque 30 Ncm.
MAXI MG-INHEX MORSE TAPER TAPERED ABUTMENT NEW
REF.
23201650
23201651
23201652
23201653
23201654
23201655
23253601
23253602
23253603
23253604
23253605
DESCRIPTION
10º Morse taper tapered abutment. MG-INHEX MAXI
10º Morse taper tapered abutment. MG-INHEX MAXI
10º Morse taper tapered abutment. MG-INHEX MAXI
10º Morse taper tapered abutment. MG-INHEX MAXI
10º Morse taper tapered abutment. MG-INHEX MAXI
10º Morse taper tapered abutment. MG-INHEX MAXI
30º Morse taper tapered abutment. MG-INHEX MAXI
30º Morse taper tapered abutment. MG-INHEX MAXI
30º Morse taper tapered abutment. MG-INHEX MAXI
30º Morse taper tapered abutment. MG-INHEX MAXI
30º Morse taper tapered abutment. MG-INHEX MAXI
Ø
0,75 mm.
H
Ø
2 mm.
H
CUFF HEIGHT (H)
0 mm
1 mm
2 mm
3 mm
4 mm
5 mm
1 mm
2 mm
3 mm
4 mm
5 mm
p. 47
Prostheses. Prosthetic System MG-InHex
Maxi MG-InHex® Prosthetic System
Ø
11 mm.
MAXI MG-INHEXMAXI MG-INHEX MORSE TAPER TAPERED ABUTMENTS NEW
REF.
13209162
13209161
13209163
13209262
13209261
13209263
13205561
13203561
13205260
13205560 / 63
13205660 / 63
13201060
13201360
DESCRIPTION
10º anti-rotational cast. post for morse taper tapered abut. w/s
10º rotational castable post for morse taper tapered abut. w/s
30º rotational castable post for morse taper tapered abut. w/s
10º anti-rotational titan. post for morse taper tapered abut. w/s
10º rotational titanium post for morse taper tapered abut. w/s
30º rotational titanium post for morse taper tapered abut. w/s
10º morse taper tapered abutment analog
30º morse taper tapered abutment analog
10º anti-rot. impr. coping for morse taper tapered abut. w/s
10º / 30º rot. impr. coping for morse taper tapered abut. w/s
10º / 30º impr. coping for morse taper tap. abut. closed tray
10º morse taper tapered abutment cap (1 piece)
30º morse taper tapered abutment cap (1 piece)
- Material: stainless steel
- Castable abutment.- Torque 20 Ncm.
*Anti-rotational castable abutments are manufactured in red colour for an easy identification.
Ø
11 mm.
Ø
11 mm.
Ø
4,2 mm.
- Grade V Titanium. - Torque 20 Ncm.
*Anti-rotational titanium abutments are manufactured in purple colour for an easy identification.
- Grade V Titanium.
* Anti-rotational abutments are manufactured in purple colour for an easy identification.
p. 48
CUFF HEIGHT (H)
2 mm
2 mm
2 mm
2 mm
2 mm
MG-INHEXMG-INHEX TEMPORARY TITANIUM UCLA ABUTMENT
REF.
23204110
23254110
23205110
23255110
DESCRIPTION
Temporary titanium Hex UCLA for MG-INHEX STD w/s
Temporary titanium Hex UCLA for MG-INHEX MAXI w/s
Temporary titanium Non-hex UCLA for MG-INHEX STD w/s
Temporary titanium Non-hex UCLA for MG-INHEX MAXI w/s
- Titanium Grade V abutment for chair side modification
- Attaches directly to implant- Screw retained- Screwdriver: 1.25 mm Hex- Retaining Surface- Easy fixation of the temporary prosthesis
Recommendations for use:- For temporary restorations to be placed for
up to 2 or 3 months- Torque 10 Ncm.
Ø
10 mm
MG-INHEX
REF.
23207151
23207155
23208151
23208155
DESCRIPTION
Temporary castable non hex UCLA MG-INHEX STD w/s
Temporary castable non hex UCLA MG-INHEX MAXI w/s
Temporary castable hex UCLA MG-INHEX STD w/s
Temporary castable hex UCLA MG-INHEX MAXI w/s
MG-INHEX TEMPORARY CASTABLE UCLA ABUTMENT
Ø
A= 10 mm
* Abutments are also available without screw.* Anti-rotational castable abutments are manufactured in red colour for an easy identification.
*Abutments are also available without screw
- Temporary castable abutment- For direct to implant restorations- For screw retained restorations- Platform STD: 2.80 mm- Platform MAXI: 3.80 mm- Ø: 4 mm - Screw driver: 1.25 mm hex
Recommendations for use:- For unitary restorations is recommended to
use hex abutments- Torque 10 Ncm
MG-INHEX2 MM HEIGHT MG-INHEX TEMPORARY PREPABLE ABUTMENT
REF.
23232110
23202110
23252110
23203110
23253110
DESCRIPTION
Temp. Prep. Abut. Hex for chair side modif. MG-INHEX MINI w/s
Temp. Prep. Abut. Hex for chair side modif. MG-INHEX STD w/s
Temp. Prep. Abut. Hex for chair side modif. MG-INHEX MAXI w/s
Temp. Prep. Abut. Non-Hex for chair side modif. MG-INHEX STD w/s
Temp. Prep. Abut. Non-Hex for chair side modif. MG-INHEX MAXI w/s
- Titanium Grade V abutment for chair side modification
- Attaches directly to implant- For single or multiple restorations- Screw retained- Screwdriver: 1.25 mm Hex- Retaining Surface- Easy fixation of the temporary prosthesis- Ø MINI: 2.3 mm- Ø STD: 2.8 mm- Ø MAXI: 3.8 mm
Recommendations for use:- For temporary restorations to be placed for
up to 2 or 3 months- Torque 10 Ncm
* Plastic cap included, except on MG-Inhex MINI. To place between the temporary crown and the abutment to ensure a better fit
* Abutments are also available without screw Plastic capFacilitates and ensures a correct passive adjustment of the aesthetic temporary crown.
[ Hex
][ H
ex ]
[ Hex
][ N
on H
ex ]
[ Non
Hex
][ N
on H
ex ]
Temporary Prostheses/Immediate Loading MG-InHex®
Prostheses. Prosthetic System MG-InHex
Ø
6,5 mm
H
7,6 mm
p. 49
MG-INHEX
MG-INHEX
TEMPORARY CASTABLE POST FOR TAPERED ABUTMENT
REF.
13205110
13205130
DESCRIPTION
Temporary castable post for 10º tapered abut. w/s
Temporary castable post for 30º tapered abut. w/s
- Abutment for chair side modification- Screwdriver: 1.25 mm Hex.- Screw retained- Retaining Surface- Easy fixation of the temporary prosthesis
Recommendations for use:- For temporary restorations to be placed for
up to 2 or 3 months- Torque 10 Ncm.
TEMPORARY TITANIUM POST FOR TAPERED ABUTMENT
REF.
13206110
13206130
DESCRIPTION
Temporary Titanium post for 10º Tapered Abut. w/s
Temporary Titanium post for 30º Tapered abut. w/s
- Abutment for chair side modification- Screwdriver: 1.25 mm Hex.- Screw retained- Retaining Surface- Easy fixation of the temporary prosthesis
Recommendations for use:- For temporary restorations to be placed for
up to 2 or 3 months- Torque 10 Ncm.
Temporary post for tapered abutmentAllows the retention of the temporary prosthesis during the immediate loading procedure.
[ Non
Hex
][ N
on H
ex ]
Temporary Prostheses/Immediate Loading MG-InHex®
Prostheses. Prosthetic System MG-InHex
Ø
11 mm.
MG-INHEXTEMP. CAST. POST FOR MORSE TAPER TAPERED ABUTMENT NEW
REF.
13205160
13205163
DESCRIPTION
Temporary castable post for 10º morse taper tapered abut. w/s
Temporary castable post for 30º morse taper tapered abut. w/s
- Abutment for chair side modification- Screwdriver: 1.25 mm Hex.- Screw retained- Retaining Surface- Easy fixation of the temporary prosthesis
Recommendations for use:- For temporary restorations to be placed for
up to 2 or 3 months- Torque 10 Ncm.
Ø
11 mm.
[ No
Hex
]
MG-INHEXTEMP. TITANIUM POST FOR MORSE TAPER TAPERED ABUT. NEW
REF.
13206160
13206163
DESCRIPTION
Temporary Titanium post for 10º morse taper tapered abut. w/s
Temporary Titanium post for 30º morse taper tapered abut. w/s
- Abutment for chair side modification- Screwdriver: 1.25 mm Hex.- Screw retained- Retaining Surface- Easy fixation of the temporary prosthesis
Recommendations for use:- For temporary restorations to be placed for
up to 2 or 3 months- Torque 10 Ncm.
Ø
11 mm.
[ No
Hex
]
Ø
11 mm.
Temporary Prostheses/Immediate Loading MG-InHex®
Prostheses. Prosthetic System MG-InHex
MG-INHEXRETAINING CAP FOR TAPERED ABUTMENT
REF.
13201200
13201230
DESCRIPTION
Retaining cap for 10º tapered abutment with screw
Retaining cap for 30º tapered abutment with screw - Screw retained.- Screw driver: 1.25 mm hex.- Retaining surface.- Easy fixation of the temporary prosthesis
Recommendations for use:- For temporary restorations to be placed for
up to 2 or 3 months- Torque 10 Ncm.
Ø
6 mm
Retaining cap for tapered abutmentAllows the adaptation of the patient’s temporary prosthesis during the immediate loading procedure.
[ Non
Hex
]p.
50
- Abutment for chair side modification- Screwdriver: 1.25 mm Hex.- Screw retained- Retaining Surface- Easy fixation of the temporary prosthesis
Recommendations for use:- For temporary restorations to be placed for
up to 2 or 3 months- Torque 10 Ncm.
- Abutment for chair side modification- Screwdriver: 1.25 mm Hex.- Screw retained- Retaining Surface- Easy fixation of the temporary prosthesis
Recommendations for use:- For temporary restorations to be placed for
up to 2 or 3 months- Torque 10 Ncm.
MG-INHEX
MG-INHEX
TEMPORARY TITANIUM POST FOR ANGLED TAPERED ABUTMENT
TEMPORARY CASTABLE POST FOR ANGLED TAPERED ABUTMENT
REF.
13206710
REF.
13205710
DESCRIPTION
Temporary Titanium post for 17º angled tapered abutment
DESCRIPTION
Temporary Castable post for 17º angled tapered abutment
[ No
Hex
][ N
o He
x ]
RETAINING CAP FOR MORSE TAPER TAPERED ABUTMENT NEW
REF.
13201260
13201263
DESCRIPTION
Retaining cap for 10º morse taper tapered abutment with screw
Retaining cap for 30º morse taper tapered abutment with screw
Ø
6 mm.[ No
Hex
]
p. 51
MG-INHEX
[ MINI ]- Ø head: 2.1 mm Ø thread: 1.4 mm
[ STANDARD ]- Ø head: 2.4 mm Ø thread: 1.6 mm
[ MAXI ]- Ø head: 2.4 mm Ø thread: 2.0 mm
STD MG-INHEX Lab Screw - Ø Head: 2.4 mm Ø Thread: 1.6 mm A=2.3
mm L=8.4 mm
MAXI MG-INHEX Lab Screw - Ø Head: 2.4 mm Ø Thread: 2.0 mm A=2.3
mm L=9.7 mm
Ø ØØ
A
L
A
L
Ø Ø
L L
A A
L
A
Ø
A
L
Screws for abutments and transfers
Prostheses. Prosthetic System MG-InHex
STANDARD MG-INHEX IMPLANT
MINI MG-INHEX IMPLANT
MAXI MG-INHEX IMPLANT
REF.
23205504
23205502
23205505
23202526
23202508
232010151
13202528
23201726
13201727
23282526
REF.
23235504
23235502
23235505
23232526
232310151
DESCRIPCIÓN
Short transfer screw L=17 mm A=9 mm MG-INHEX MINI
Long transfer screw L=23 mm A=17 mm MG-INHEX MINI
Transfer screw for waxing MG-INHEX MINI Ø head=2.1 mm Ø thread= 1.4. L=29 mm A=23 mm
Retaining screw hex. 1.25 mm L= 8.6 mm MG-INHEX MINI
Retaining screw for angled abutment L= 8.20 mm MG-INHEX MINI
REF.
23205004
23205002
23205005
23205025
23202509
232510151
13202528
23251726
13201727
23285025
DESCRIPTION
Short transfer screw L=14 mm A=8 mm MG-INHEX STD
Long transfer Screw L=20 mm A=14 mm MG-INHEX STD
Transfer screw for waxing L=26 mm A=20 mm MG-INHEX STD
Retaining screw Hex 1.25 mm L=7.7 mm A=1.7 mm MG-INHEX STD
Ret. screw w/slot for dif. sit. L=6.9 mm A=1.2 mm MG-INHEX STD
Ret. screw for ang. abut. L=6.9 mm A=1.2 mm MG-INHEX STD
Prosthetic screw for castable/titanium tapered abutment L=4.7 mm A=1.7 mm MG-OSSEOUS/INHEX
Retaining screw for 17º angled tapered abut. MG-INHEX STD
Prosth. screw for 17º angled tap. abut. MG-OSSEOUS/INHEX
Lab screw MG-INHEX STD (5 pcs)
DESCRIPTION
Short transfer screw L=14 mm A=8 mm MG-INHEX MAXI
Long transfer Screw L=20 mm A=14 mm MG-INHEX MAXI
Transfer screw for waxing L=26 mm A=20 mm MG-INHEX MAXI
Ret. screw Hex 1.25 mm L=7.7 mm A=1.7 mm MG-INHEX MAXI
Ret. screw w/slot for dif. sit. L=6.9 mm A=1.2 mm MG-INHEX MAXI
Ret. screw for angled abut. L=6.9 mm A=1.2 mm MG-INHEX MAXI
Prosthetic screw for castable/titanium tapered abutment L=4.7 mm A=1.7 mm MG-OSSEOUS/INHEX
Retaining screw for 17º angled tapered abutment MG-INHEX MAXI
Prost. screw for 17º angled tapered abutment MG-OSSEOUS/INHEX
Lab screw MG-INHEX MAXI (5 pcs)
MG-Fidelis®
Surgical kit for Computer-Guided Surgery
Fidelis
Surgicalmaterial
p. 54
PRE-TREATMENT
TREATMENT DURING USE
TREATMENT AFTER USE
Surgical material. Instructions for maintenance
Instructions for maintenance of surgical instruments
All products must be cleaned, disinfected and sterilized prior to use; this applies in particular prior to first use
i.e. after delivery as all products are supplied nonsterile. The thorough cleaning and disinfecting is indispensable
in order to achieve effective sterilization. The disinfectant used during pre-treatment only ensures personal
protection and can be no substitute for the disinfection procedure to be used later after completion of the
cleaning process.
During use, separate the soiled instruments to avoid further contamination of the instrument tray. Clean /
disinfect the soiled products, arrange them in the instrument tray, and sterilize only the instruments that will
be used.
Impurities must be removed from the products directly after use. To do so, use distilled water or a disinfectant
solution; the disinfectant must not contain aldehyde (which could fix blood residues to the instrument surface).
1. Choosing the cleaning / disinfecting agents: It is recommended to use a neutral/enzymatic detergent
(minimum admissible pH value 5.5). It should contain neither bleach nor Organic solutions (e.g. alcohols,
ether), nor oxidants (e.g. hydrogen peroxides), nor halogens (chlorine, iodine, bromine). Caution should be
paid with tap water as it may contain too much chlorine. Avoid solutions with aldehyde (which could fix
blood residues to the instrument surface).
2. Choosing the products for the cleaning process: For the manual removal of impurities, only use
nylon brushes. Never use metal brushes or steel wool. Use a wire to clean the internal cooling canal of the
drills (Not applicable to RCD drills).
3. How to clean / disinfect the surgical instruments: Eliminate thoroughly all the post-operative
residues (blood, bone....). As to products with lumen (cavities), such as drills with internal cooling, rinse
all cavities by using a disposable syringe and a wire for this purpose (Not applicable to RCD drills). Do
not clean, implant drills with other tools made of different material, in the same ultrasonic box. During
the cleaning process in ultrasonic box, avoid as much as possible, shocks and contacts with other drills or
instruments. Rinse and dry the drills immediately after the cleaning process (preferably use distilled water
to rinse). Never store instruments while they are still wet.
4. How to sterilize: Sterilization by wet heat autoclaving 134 ºC (273 ºF) - 18 minutes (5 minutes in case
of RCD drills). Make sure that the elements, inside the autoclave, are not rusted. Wrap the elements in
sterilization packaging intended for this purpose. Never allow surgical instruments to touch one another
while being sterilized. Surgical instruments and sterilization trays should never be exposed to temperatures
exceeding 137 °C (279 °F).
REF. 15400004
Locator drill
2.0 mm twist drill
Conical drills:
3.0 / 3.3 / 3.8 / 4.3 / 4.7 mm
Profile drills: 3.3 / 3.7 / 4.2 / 4.95 mm
Conical drills for hard bones:
3.2 / 3.5 / 4.0 / 4.9 mm
1.25 mm long hex screwdriver
Paralleling pins: 4.1 / 5.0 mm
C/A implant mount driver
16 mm ratchet wrench extender
15 mm drill extender
STD MG-INHEX depth gauge
MAXI MG-INHEX 20 mm long implant mount
STD MG-INHEX 20 mm long implant mount
Hexed hand wrench
Ratchet wrench with Hex. converter
Open-end wrench
Surgical kit box
MG-INHEX SURGICAL KIT
Locator drill
2.0 mm twist drill.
3.0 mm conical drill.
3.3 mm conical drill
3.8 mm conical drill
4.3 mm conical drill
4.7 mm conical drill
3.2 mm conical drill. Hard bone
3.5 mm conical drill. Hard bone
4.0 mm conical drill. Hard bone
4.9 mm conical drill. Hard bone
2.0 mm long twist drill.
3.0 mm long conical drill.
3.3 mm long conical drill
3.8 mm long conical drill
4.3 mm long conical drill
4.7 mm long conical drill
3.3 mm profile drill
3.75 mm profile drill
4.25 mm profile drill
5.0 mm profile drill
3.3 mm bone tap
3.75 mm bone tap
4.25 mm bone tap
5.0 mm bone tap
Paralleling pins (2 units)
STD MG-INHEX depth gauge
MAXI MG-INHEX depth gauge
STD MG-INHEX long implant mount
MAXI MG-INHEX long implant mount
4.0 mm C/A circular tissue punch
5.0 mm C/A circular tissue punch
Drill extender
9 mm ratchet wrench extender
16 mm ratchet wrench extender
C/A Implant mount driver
Ratchet wrench with Hex converter
Open-end wrench
1.25 mm short hex screwdriver
1.25 mm long hex screwdriver
1.25 mm short C/A hex screwdriver
1.25 mm long C/A hex screwdriver
Plus surgical kit box
MG-INHEX PLUS SURGICAL KIT
REF. 15405430
Surgical material. Surgical kits
Surgical kits
p. 55
RCD STRAIGHT CONICAL DRILLS NEW
Surgical material. Drills for implants
p. 56
Drills for implants
- Color ring- Long drills lenght: 20 mm- Short drills length: 16 mm- Material: Stainless steel- Internal irrigation- Short drills depth marks: 8-9-10-11.5-13-15 mm- Long drills depth marks:
8-9-10-11.5-13-15-18-20 mm
Recommendations for use:- Use and sterilise the drills up to 3 surgeries- Sterilise only the drills used in the surgery
REF.
13903230
13903233
13903238
13903243
13903247
13923230
13923233
13923238
13923243
13923247
REF.
13903230
13903233
13903238
13903243
13903247
13963230
13963233
13963238
13963243
13963247
ø
3.0 mm
3.3 mm
3.8 mm
4.3 mm
4.7 mm
3.0 mm
3.3 mm
3.8 mm
4.3 mm
4.7 mm
ø
3.0 mm
3.3 mm
3.8 mm
4.3 mm
4.7 mm
3.0 mm
3.3 mm
3.8 mm
4.3 mm
4.7 mm
LENGTH
16 mm
16 mm
16 mm
16 mm
16 mm
20 mm
20 mm
20 mm
20 mm
20 mm
LENGTH
16 mm
16 mm
16 mm
16 mm
16 mm
20 mm
20 mm
20 mm
20 mm
20 mm
STRAIGHT CONICAL DRILLS
LOCATOR DRILLS
- Material: Stainless steel - Internal irrigation - Locator drill depth marks: 8-9 mm - 2.0 mm drills depth marks: 8-9-10-11.5-13-15
mm - 6-mm depth mark drill depth marks: 6-8-9-10-
11.5-13-15 mm- 2.0 mm Long drills depth marks: 8-9-10- 11.5-
13-15-18-20 mm
Recommendations for use:- Use and sterilise the drills up to 3 surgeries (RCD
Drills 5 surgeries)- Sterilise only the drills used in the surgery
- Color ring- Drills lenght: 16 mm- Material: Stainless steel, Diamong-Like Carbon
coated- No internal irrigation- Depth marks: 8-9-10-11.5- 13-15 mm- Long drills depth marks:
8-9-10-11.5-13-15-18-20 mm Recommendations for use: - Use and sterilise the drills up to 5 surgeries- Sterilize only the drills used in the surgery
REF. ø LENGTH DEPTH MARKING
13202020 1.5-2.2mm 8 mm
132020206 6 mm
13901620 2.0 mm 16 mm
139016206 2.0 mm 16 mm 6 mm
13911620 new rdc 2.0 mm 16 mm
13902120 2.0 mm 21 mm
Drills for implants
- Color ring- Drills lenght: 16 mm- Material: Stainless steel- Internal irrigation- Depth marks: 6- 8-9-10-11.5- 13-15 mm
Recommendations for use:- 3 uses- Sterilize only the drills used in the surgery
REF.
139032306
139032336
139032386
139032436
139032476
Ref.
Short straight conical drill 3.0 mm - 6 mm depth mark
Short straight conical drill 3.3 mm - 6 mm depth mark
Short straight conical drill 3.8 mm - 6 mm depth mark
Short straight conical drill 4.3 mm - 6 mm depth mark
Short straight conical drill 4.7 mm - 6 mm depth mark
STRAIGHT CONICAL DRILLS WITH 6 MM DEPTH MARK
REF.
13903232
13903235
13903240
13903249
ø
3.2 mm
3.5 mm
4.0 mm
4.9 mm
STRAIGHT CONICAL DRILLS FOR HARD BONE
LENGTH
16 mm
16 mm
16 mm
16 mm
- Double color ring- Short drills lenght: 16 mm- Material: Stainless steel- Internal Irrigation- Short drills depth marks: 8-9-10-11.5-13-
15 mm
Recommendations for use:- Use and sterilise the drills up to 3 surgeries- Sterilise only the drills used in the surgery
Surgical material. Drills for implants
p. 57
RCD STRAIGHT CONICAL DRILLS FOR HARD BONE
REF. ø LENGTH- Double color ring- Drills lenght: 16 mm- Material: Stainless steel, Diamong-Like Carbon
coated- No internal irrigation- Depth marks: 8-9-10-11.5- 13-15 mm
Recommendations for use:- 5 uses- Sterilize only the drills used in the surgery
13913232 new 3,2 mm 16 mm
13913235 new 3,5 mm 16mm
13913240 new 4,0 mm 16mm
13913249 new 4,9 mm 16mm
Surgical material. Drills for implants
p. 58
Drills for implants
REF.
13102032
13102037
13102042
13102049
DESCRIPTION
Profile drill 3.3 mm MG-INHEX
Profile drill 3.75 mm MG-INHEX
Profile drill 4.25 mm MG-INHEX
Profile drill 5.0 mm MG-INHEX
PROFILE DRILLS
- Material: Stainless steel
Recommendations for use:- Sterilise only the drills used in the surgery
BONE TAPS
- Material: Stainless steel- Depth marks: 6-8-9-10-11.5-13-15 mm
Recommendations:- Drill speed: 15 rpm
REF.
13107340
13107375
13107425
13107500
DESCRIPTION
Bone tap 3.3 / 3.40 mm MG-OSSEOUS/INHEX
Bone tap 3.75 mm MG-OSSEOUS/INHEX
Bone tap 4.25 mm MG-OSSEOUS/INHEX
Bone tap: 5.0 mm MG-OSSEOUS/INHEX
RCD DRILL STOP KIT
This kit is composed of all the stop range for Mozo Grau RCD (Diamond-like carbon) drills
Instructions for use: 1. Insert the drill into the contra-angle and
select the appropriate drill stop according to the desired drillings depth.
2. Insert the drill to the end of drill stop.3. Verify drilling depth by using the drill
depth guide. 4. To release the stop from the drill, insert
the contra-angle in the appropriate metallic sheet and pull up. The stop will fall safely into the box.
REF. DESCRIPTION- Sterilizable material- Delivers stop easy pick-up and release.- Stop color-coding and organization in
the box aid in easy identification.- Reduced size to facilitate storage and
sterilization.- Measurement guide aid to ensure a
safe drilling process.- Depth identification for each stop
group (A, B or C).
15400007 new DRILL STOP KIT
This kit includes 21 drill stops to place implants (from 6 mm to 15 mm long) with RCD (Diamond-like carbon) drills
Surgical material
LONG IMPLANT MOUNTS
REF.
23207004
23207001
23207009
DESCRIPTION
Long implant mount 20 mm INHEX MINI
Long implant mount 20 mm INHEX STD
Long implant mount 20 mm INHEX MAXI
Recommendations for use:- Replace the normal implant mount in
difficult situations (limited interdental space available).
- Millimeter marks: useful on flapless surgeries
SURGICAL WRENCHES
REF.
23208000
14608010
14650185
18089021
14659021
13209022
DESCRIPCIÓN
Open-end wrench
Ratchet wrench
Dynamometrical ratchet wrench 45 Ncm.
Multiconverter for C/A latch
Hexed dynamometrical ratchet wrench adapter
Hexed hand wrench
Open-end wrench Recommendations for use: - To hold the implant mount while it is
unscrewed. Suitable for cases with little primary stability.
Ratchet wrench: Recommendations for use: - To insert implant - To insert non-traumatic bone expanders
Dynamometrical ratchet wrenchRecommendations for use: - To ensure a proper implant insertion torque
Multiconverter for C/A latchRecommendations for use: - To be used with C/A tissue punches and C/A
screwdrivers
Hexed dynamometrical ratchet wrenchRecommendations for use:- To insert implant with the dynamometrical
ratchet wrench
Hand wrench Recommendations for use: - To insert implant by hand
Surgical material. Surgical Wrenches
p. 59
REF. DESCRIPTION- Sterilizable material- Delivers stop easy pick-up and release.- Stop color-coding and organization in
the box aid in easy identification.- Reduced size to facilitate storage and
sterilization.- Measurement guide aid to ensure a
safe drilling process.- Depth identification for each stop
group (A, B or C).
15400007 new DRILL STOP KIT
This kit includes 21 drill stops to place implants (from 6 mm to 15 mm long) with RCD (Diamond-like carbon) drills
p. 60
Surgical material
RATCHET WRENCH AND DRILL EXTENDERS
REF.
23208009
23208016
14602000
DESCRIPTION
Ratchet wrench extender 9 mm
Ratchet wrench extender 16 mm
Drill extender 15 mm
Recommendations for use: - To be used when limited interdental space
is available. - To be used when adjacent teeth height does
not allow C/A a proper drilling. - In some cases, to be used to replace long
drills.
C/A IMPLANT MOUNT DRIVER AND CONVERTER
REF.
23209021
23209121
DESCRIPTION
C/A implant mount driver
Square to Hexagon converter for Ratchet wrench
Recommendations for use: - To insert implants with C/A
DEPTH GAUGES
REF.
23209006
23209007
23209008
13109009
DESCRIPTION
1.7 – 2.5 mm depth gauge. MINI MG-INHEX
1.8 – 3.2 mm depth gauge. STD MG-INHEX
2.2 – 4.1 mm depth gauge. MAXI MG-INHEX
2.0 mm angled depth gauge
- Material: stainless steel- D epth marks:
8-9-10-11,5-13-15 mm.
PARALLELING PIN
- To ensure implant parallelism at the beginning of the surgery
- The pin ring matches the implant platform
REF.
13109034
13109041
13109050
DESCRIPTION
Paralleling pin for MINI platform
Paralleling pin for STD platform
Paralleling pin for MAXI platform
Ø
Surgical material. Surgical Wrenches
- An easy system for bone expansion or pressing which allows a measured and progessive control. Indicated for thin crests or type IV bone crests (pressing). It allows a perfect control of the implants insertion axis.
- Surgical technique: The expanders should be introduced following a slow and sequential method. Once an excessive resistance is encountered, the insertion should be stopped for a few seconds to avoid heating and, then, continue with the normal insertion sequence until the desired depth is reached. The size pattern will help to identify the exact width of each expander according to their depth markings.
Recommendations for use:- Recommended for thin crests or to compact
bone in crest where Tipe IV bones are present. Recommendable only for upper maxilla
Upper maxilla bone expansion with MG-Expanders
NON-TRAUMATIC MG-EXPANDERS SET
REF.
13203041
13200445
DESCRIPTION
Non-traumatic MG-Expanders set. Size pattern and hand wrench included
Hand wrench for MG-Expanders
Advanced surgery. Bone expansion
Bone expansion
p. 61
Advanced surgery. Accessories
Accessories
BONE COLLECTOR
REF.
14309110
13109110
DESCRIPTION
Bone collector with aspirator tip
Disposable Filter Cartridge, sterile. One single use.
- By using the bone collector during the osteotomy with saws, handpieces, crest regularisations, etc., we will obtain a great amount of graft material to repair different types of tissues
Recommendations for use:- It is recommended the use of the bone
collector only during the drilling process and only for this process. Use another aspirator tip to draw in blood and saliva and approach as much as possible the aspirator tip to the drill
PARALLEL PIN GUIDEREF.
17690035
DESCRIPTION
Parallel Pin Guide
- To secure parallelism between implant- Drill an alveolus with the 2.0 mm drill. Enter
the spike into this alveolus and adjust the hinge until the open arm reaches the desired location of the following implant. Then, drill a new alveolus through the open end guide hole
Recommendations for use:- Mandatory to be used when placing
ball abutments in overdentures to avoid disparallelism
p. 62
www.mozo-grau.com
HEADQUARTERS
SPAINMOZO-GRAU S. A.C/ Santiago López González, 7. 47197 ValladolidTel: +34 983 211 312Fax: +34 983 304 021info@mozo-grau.com
SUBSIDIARY
POLANDMOZO-GRAU Sp. z o.o.ul. Grójecka 22/24 lok. 52. 02-301 Warszawatel./fax: +48 22 658 41 21biuro@mozo-grau.com
www.mozo-grau.com
Follow us:
A L B A N I A C H I L E C H I N A C O L O M B I A E G Y P T I R A N
I TA LY M E X I C O P O L A N D R O M A N I A S P A I N TA I WA N
DISTRIBUTOR
Recommended