CANM8-NAV Installation File Accura RDX · 2013-12-18 · CANM8-NAV Installation File Accura RDX...

>>>>>>>>>>

CANM8-NAV Installation File

Accura RDX

Vehicle CAN Bus Location

CANM8-NAV Wiring Instructions

CAN HI = OBD Socket - Pin 6CAN LO = OBD Socket - Pin 14

The CAN wiring is located at the OBD socket, under the drivers side dash.

Connect to a good chassis ground point.CAN HI Connection : Vehicle CAN HI wire

CAN-M8 NAV Wire Wire Connection Point Or Output Function

RED Connect via a 5 Amp fuse to a permanent 12V supply.

BLUEGREENPURPLEORANGE

BLACKWHITE

CAN LO Connection : Vehicle CAN LO wire

Reverse Engaged Output : 12v when reverse gear is selected.BROWNYELLOW RPM Output : 12v pulsing 1Hz = 1RPM (approx).

Speed Signal Output : 12v pulsing 1Hz = 1MPH (approx).Ignition On Output : 12v when ignition is switched on.Lights On Output : 12v when side / head lights are on.Parking Brake On Output : 0v (Ground) with parking brake on.

Unclip the socket for access. The CAN bus wiring is a twisted pair of wires, coloured as below:

CAN-M8 PARK Wire Wire Connection Point Or Output Function

Connect to a good chassis ground point.WHITE CAN HI Connection : Vehicle CAN HI wire

Please note: Some outputs may be un-available depending on the specification of the subject vehicle.

CANM8-PARK Wiring Instructions

Connect via a 5 Amp fuse to a SWITCHED 12V supply.BLACK

>>>>>>>

Connect the interface to the plug-in wiring harness and turn the vehicles ignition 'on'.

PINK FPS Disable : 0v Output - Disabled when Reverse is selected.BROWN Reverse Engaged Output : 12v when reverse gear is selected.

BLUE CAN LO Connection : Vehicle CAN LO wire

Speed Dependent Output : 12v continuously while below 6 MPHORANGE Speed Dependent Output : 12v between speeds of 1 to 6 MPH

GREEN Speed Signal Output : 12v pulsing 1Hz = 1MPH (approx).PURPLE

NOT USED

Testing The Installation

If the LED indicator is illuminated costantly, the interface is functioning but cannot identify the

The CANM8 interface switches on automatically when CAN activity is detected.

The Orange & Purple outputs will switch off when the vehicle Park Brake is applied on compatible vehicles.YELLOW

If the LED fails to illuminate or flash, the interface wiring has been connected incorrectley orno CAN activity has been detected. Check all electrical connections are sound and that the

interface CAN HI and CAN LO connections are the correct way around. Also check that there is

subject vehicle. It is very important that the interface is only connected to the vehicle CAN Bus

The interface has an LED status indicator next to the connection plug, which will flash constantlywhen a CAN signal is present and has been identified by the interface.

wiring at the connection point location detailed at the top of the page.

switching all auxilliary equipment 'off'. The interface LED should extinguish within 60 seconds.

a good 12v supply present at the interface plug-in connector before seeking technical assistance.

The CANM8 interface automatically switches off when the vehicle CAN Bus is inactive.This can be tested by removing the keys from the ignition, closing all vehicle doors and

>>>>>>>>>>

>>>>BLUE CAN LO Connection : Vehicle CAN LO wire

RED Connect via a 5 Amp fuse to a SWITCHED 12V supply.BLACK Connect to a good chassis ground point.WHITE CAN HI Connection : Vehicle CAN HI wire

RPM Output : 12v pulsing 1Hz = 1RPM (approx).

CANM8-PARK Wiring InstructionsCAN-M8 PARK Wire Wire Connection Point Or Output Function

YELLOW

Connect via a 5 Amp fuse to a permanent 12V supply.Connect to a good chassis ground point.CAN HI Connection : Vehicle CAN HI wireCAN LO Connection : Vehicle CAN LO wireSpeed Signal Output : 12v pulsing 1Hz = 1MPH (approx).Ignition On Output : 12v when ignition is switched on.Lights On Output : 12v when side / head lights are on.Parking Brake On Output : 0v (Ground) with parking brake on.Reverse Engaged Output : 12v when reverse gear is selected.

BLUEGREENPURPLEORANGEPINKBROWN

REDBLACKWHITE

Alfa Romeo : Brera

CAN LO = PIN 14 (Or CAN 'A' at the radio)CAN wiring is also available at the radio. The wire location details are on the Pin-Out diagram

on the top of the radio.

The CAN wiring is located at the OBD socket, drivers dash fuse box behind dash panel.

CAN HI = PIN 6 (Or CAN 'B' at the radio)

>>>>>>

ORANGE Speed Dependent Output : 12v between speeds of 1 to 6 MPHPINK FPS Disable : 0v Output - Disabled when Reverse is selected.

The Orange & Purple outputs will switch off when the vehicle Park Brake is applied on compatible vehicles.Please note: Some outputs may be un-available depending on the specification of the subject vehicle.

BROWN Reverse Engaged Output : 12v when reverse gear is selected.YELLOW NOT USED

GREEN Speed Signal Output : 12v pulsing 1Hz = 1MPH (approx).PURPLE Speed Dependent Output : 12v continuously while below 6 MPH

This can be tested by removing the keys from the ignition, closing all vehicle doors and switching all auxilliary equipment 'off'. The interface LED should extinguish within 60 seconds.

interface CAN HI and CAN LO connections are the correct way around. Also check that there isa good 12v supply present at the interface plug-in connector before seeking technical assistance.

when a CAN signal is present and has been identified by the interface.

If the LED indicator is illuminated costantly, the interface is functioning but cannot identify thesubject vehicle. It is very important that the interface is only connected to the vehicle CAN Bus

The CANM8 interface automatically switches off when the vehicle CAN Bus is inactive.

The CANM8 interface switches on automatically when CAN activity is detected.The interface has an LED status indicator next to the connection plug, which will flash constantly

>>>>>>>>>>

Alfa Romeo : GT

Parking Brake On Output : 0v (Ground) with parking brake on.

BLACKWHITEBLUEGREEN

RED Connect via a 5 Amp fuse to a permanent 12V supply.Connect to a good chassis ground point.CAN HI Connection : Vehicle CAN HI wireCAN LO Connection : Vehicle CAN LO wire

Reverse Engaged Output : 12v when reverse gear is selected.

PURPLEORANGEPINK

Speed Signal Output : 12v pulsing 1Hz = 1MPH (approx).Ignition On Output : 12v when ignition is switched on.Lights On Output : 12v when side / head lights are on.

RED Connect via a 5 Amp fuse to a SWITCHED 12V supply.

BROWNYELLOW RPM Output : 12v pulsing 1Hz = 1RPM (approx).

BLACK Connect to a good chassis ground point.WHITE CAN HI Connection : Vehicle CAN HI wire

>>>>>>>

when a CAN signal is present and has been identified by the interface. The interface has an LED status indicator next to the connection plug, which will flash constantly

PINK FPS Disable : 0v Output - Disabled when Reverse is selected.BROWN Reverse Engaged Output : 12v when reverse gear is selected.YELLOW NOT USED

BLUE CAN LO Connection : Vehicle CAN LO wireGREEN Speed Signal Output : 12v pulsing 1Hz = 1MPH (approx).

Speed Dependent Output : 12v between speeds of 1 to 6 MPH

The Orange & Purple outputs will switch off when the vehicle Park Brake is applied on compatible vehicles.

PURPLE Speed Dependent Output : 12v continuously while below 6 MPHORANGE

>>>>>>>>>>

GREENPURPLEORANGEPINK

RED Connect via a 5 Amp fuse to a permanent 12V supply.BLACKWHITEBLUE

Connect to a good chassis ground point.CAN HI Connection : Vehicle CAN HI wireCAN LO Connection : Vehicle CAN LO wire

Alfa Romeo : Giulietta

>>>>>>>

GREEN Speed Signal Output : 12v pulsing 1Hz = 1MPH (approx).

The interface has an LED status indicator next to the connection plug, which will flash constantly

YELLOW NOT USED

>>>>>>>>>>

Alfa Romeo : Mito

BLACKWHITEBLUEGREEN

Ignition On Output : 12v when ignition is switched on.Lights On Output : 12v when side / head lights are on.Parking Brake On Output : 0v (Ground) with parking brake on.Reverse Engaged Output : 12v when reverse gear is selected.

PURPLEORANGEPINKBROWN

CANM8-PARK Wiring InstructionsCAN-M8 PARK Wire Wire Connection Point Or Output Function

YELLOW

Connect via a 5 Amp fuse to a permanent 12V supply.Connect to a good chassis ground point.CAN HI Connection : Vehicle CAN HI wireCAN LO Connection : Vehicle CAN LO wireSpeed Signal Output : 12v pulsing 1Hz = 1MPH (approx).

WHITE CAN HI Connection : Vehicle CAN HI wireBLUE CAN LO Connection : Vehicle CAN LO wire

RED Connect via a 5 Amp fuse to a SWITCHED 12V supply.BLACK Connect to a good chassis ground point.

>>>>>>

>>>>>>>>>>

The CAN bus wiring is a twisted pair of wires, coloured as below:

Connect via a 5 Amp fuse to a SWITCHED 12V supply.BLACK Connect to a good chassis ground point.

WHITE CAN HI Connection : Vehicle CAN HI wire

CANM8-PARK Wiring InstructionsPlease note: Some outputs may be un-available depending on the specification of the subject vehicle.

YELLOW

Connect via a 5 Amp fuse to a permanent 12V supply.Connect to a good chassis ground point.CAN HI Connection : Vehicle CAN HI wireCAN LO Connection : Vehicle CAN LO wireSpeed Signal Output : 12v pulsing 1Hz = 1MPH (approx).Ignition On Output : 12v when ignition is switched on.Lights On Output : 12v when side / head lights are on.

BLUEGREEN

Parking Brake On Output : 0v (Ground) with parking brake on.Reverse Engaged Output : 12v when reverse gear is selected.

REDBLACKWHITE

Alfa Romeo : 147

CAN LO = BROWN

The CAN wiring is located at the control unit, in the passenger side footwell under the floor panel.

CAN HI = GREEN

>>>>>>>

YELLOW NOT USED

ORANGE Speed Dependent Output : 12v between speeds of 1 to 6 MPH

Speed Signal Output : 12v pulsing 1Hz = 1MPH (approx).PURPLE Speed Dependent Output : 12v continuously while below 6 MPH

BROWN Reverse Engaged Output : 12v when reverse gear is selected.PINK FPS Disable : 0v Output - Disabled when Reverse is selected.

BLUE CAN LO Connection : Vehicle CAN LO wireGREEN

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Alfa Romeo : 159

CAN LO = PIN 14 (PINK / WHITE)CAN wiring is also available at the radio. The wire location details are on the Pin-Out diagram

on the top of the radio. The CAN HI wire may be marked as 'CAN B' and the LO wire as 'CAN A'

CAN HI = PIN 6 (PINK / BLACK)

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

YELLOW

REDBLACKWHITE

Aston Martin : DB9

The CAN wiring is located at the OBD socket, under the passenger side dash.

>>>>>>>

PURPLE Speed Dependent Output : 12v continuously while below 6 MPH

YELLOW NOT USED

ORANGE Speed Dependent Output : 12v between speeds of 1 to 6 MPHPINK FPS Disable : 0v Output - Disabled when Reverse is selected.BROWN Reverse Engaged Output : 12v when reverse gear is selected.

>>>>>>>>>>

Aston Martin : Vantage

The CAN wiring is located at the Body Diagnostic socket, drivers side, bottom of the dash panel.

GREEN Bus : CAN HI = GREEN / BROWN CAN LO = GREEN / BLACKRED Bus : CAN HI = RED / BROWN CAN LO = RED / BLACK

There are 2 diagnostic sockets marked 'Body' & 'OBD'. The OBD CAN wiring is inactive.

BLACKWHITEBLUEGREEN

Lights On Output : 12v when side / head lights are on.Parking Brake On Output : 0v (Ground) with parking brake on.Reverse Engaged Output : 12v when reverse gear is selected.

Connect via a 5 Amp fuse to a permanent 12V supply.Connect to a good chassis ground point.CAN HI Connection : Vehicle CAN HI wireCAN LO Connection : Vehicle CAN LO wireSpeed Signal Output : 12v pulsing 1Hz = 1MPH (approx).Ignition On Output : 12v when ignition is switched on.

YELLOW

Two CAN Buses are available at the Body socket. Connect to the GREEN Bus.

>>>>>>>

>>>>>>>>>>

>>> CAN HI Connection : Vehicle CAN HI wire

RED Connect via a 5 Amp fuse to a SWITCHED 12V supply.BLACK Connect to a good chassis ground point.WHITE

Connect via a 5 Amp fuse to a permanent 12V supply.Connect to a good chassis ground point.CAN HI Connection : Vehicle CAN HI wireCAN LO Connection : Vehicle CAN LO wire

ORANGEPINK

REDBLACKWHITEBLUEGREENPURPLE

CAN HI = ORANGE / GREENCAN LO = ORANGE / BROWN

The CAN wires are a twisted pair coloured as below:

Audi A1 : 2010 >

Vehicle CAN Bus LocationThe CAN wiring is located in the steering column loom.

>>>>>>>

BLUE CAN LO Connection : Vehicle CAN LO wireGREEN Speed Signal Output : 12v pulsing 1Hz = 1MPH (approx).PURPLE

Speed Dependent Output : 12v continuously while below 6 MPHORANGE Speed Dependent Output : 12v between speeds of 1 to 6 MPHPINK FPS Disable : 0v Output - Disabled when Reverse is selected.

>>>>>>>>>>

Audi A3 : 2003 >

Vehicle CAN Bus LocationRemove the lower steering column cover to expose the loom to the wiper / indicator controls.

Some vehicles may also have CAN wiring present at the audio connector.CAN HI = ORANGE / GREEN

CAN LO = ORANGE / BROWN

REDBLACKWHITEBLUE

Connect via a 5 Amp fuse to a permanent 12V supply.Connect to a good chassis ground point.CAN HI Connection : Vehicle CAN HI wireCAN LO Connection : Vehicle CAN LO wireSpeed Signal Output : 12v pulsing 1Hz = 1MPH (approx).Ignition On Output : 12v when ignition is switched on.Lights On Output : 12v when side / head lights are on.Parking Brake On Output : 0v (Ground) with parking brake on.

BROWNYELLOW

>>>>>>>

YELLOW NOT USED

Speed Dependent Output : 12v continuously while below 6 MPHORANGE Speed Dependent Output : 12v between speeds of 1 to 6 MPHPINK FPS Disable : 0v Output - Disabled when Reverse is selected.BROWN Reverse Engaged Output : 12v when reverse gear is selected.

>>>>>>>>>>

ORANGEPINK

Some vehicles may also have CAN wiring present at the audio connector.CAN HI = ORANGE / GREEN

Audi A3 : 2012 >

Vehicle CAN Bus LocationRemove the lower steering column cover to expose the loom to the wiper / indicator controls.

>>>>>>>

>>>>>>>>>>

>>> CAN HI Connection : Vehicle CAN HI wireWHITE

BLACK Connect to a good chassis ground point.RED Connect via a 5 Amp fuse to a SWITCHED 12V supply.

ORANGEPINK

CAN HI = ORANGE / PURPLE

CAN LO = ORANGE / BROWN Software versions before 25.1 will not work on the audio CAN wiring if the factory audio unit is removed.

Connect to the Orange / Green CAN Bus - usually available under the O/S dash or at the speedo connectors.

The interface is installed to the CAN wiring at the audio connector:

Audi A4 > 2007

Vehicle CAN Bus LocationRemove the audio unit.

>>>>>>>

YELLOW NOT USED

Testing The InstallationConnect the interface to the plug-in wiring harness and turn the vehicles ignition 'on'.

BLUE CAN LO Connection : Vehicle CAN LO wireGREEN Speed Signal Output : 12v pulsing 1Hz = 1MPH (approx).PURPLE Speed Dependent Output : 12v continuously while below 6 MPH

>>>>>>>>>>

rear of the glove box. There are two CAN Bus systems that can be connected to:

Audi A4 2008 >

Vehicle CAN Bus LocationThe CAN Bus wiring can be located in the steering column loom and in the wiring harness at the

CAN HI = ORANGE / PURPLE OR ORANGE / GREENCAN LO = ORANGE / BROWN

REDBLACKWHITEBLUE

BROWNYELLOW

>>>>>>>

YELLOW NOT USED

Speed Dependent Output : 12v between speeds of 1 to 6 MPHPINK FPS Disable : 0v Output - Disabled when Reverse is selected.BROWN Reverse Engaged Output : 12v when reverse gear is selected.

ORANGEPURPLE Speed Dependent Output : 12v continuously while below 6 MPH

>>>>>>>>>>

RED Connect via a 5 Amp fuse to a SWITCHED 12V supply.BLACK

ORANGEPINK

CAN HI = ORANGE / PURPLE OR ORANGE / GREENCAN LO = ORANGE / BROWN

Audi A5 & S5

>>>>>>>

YELLOW NOT USED

PURPLE

Speed Dependent Output : 12v continuously while below 6 MPH

>>>>>>>>>>

The interface is installed to the CAN wiring at the audio connector or in the looms near the fuse box

Audi A6 : 2004 >

Vehicle CAN Bus LocationRemove the audio unit or connect under the drivers dash.

CAN HI = ORANGE / PURPLE (AUDIO) ORANGE / GREEN (UNDER DASH)CAN LO = ORANGE / BROWN

REDBLACKWHITEBLUE

BROWNYELLOW

>>>>>>>

YELLOW NOT USED

ORANGEPURPLE Speed Dependent Output : 12v continuously while below 6 MPH

>>>>>>>>>>

ORANGEPINK

The interface is installed to the CAN wiring at the steering column loom.

Audi A6 : 2011 >

Vehicle CAN Bus LocationRemove the lower drivers side dash trim panel..

>>>>>>>

ORANGE

YELLOW NOT USED

>>>>>>>>>>

The interface is installed to the CAN wiring in the steering column loom.

Remove the lower drivers side dash trim.

Audi A7 : 2011 >

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

ORANGEPINK

Audi A8 : 2003 >

>>>>>>>

YELLOW NOT USED

PURPLE

>>>>>>>>>>

The interface is installed to the CAN wiring at the BCM module, near to the centre of the car:

Audi A8 : 2011

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

ORANGEPINK

CAN HI = ORANGE / GREEN

CAN LO = ORANGE / BROWNConnection can also be made to the ORANGE / BLACK (HI) & ORANGE / BROWN (LO) wires.

These are located in the main wiring at the front & back of the vehicle

. The CAN wiring is a twisted pair of wires as below:

Audi Q3 2011 >

Vehicle CAN Bus LocationThe CAN Bus wiring can be located in the steering column loom and in the wiring entering the front doors.

>>>>>>>

YELLOW NOT USED

PURPLE

>>>>>>>>>>

rear of the glove box. The CAN wiring is a twisted pair of wires as below:

Audi Q5 2008 >

REDBLACKWHITEBLUE

BROWNYELLOW

>>>>>>>

>>>>>>>>>>

ORANGEPINK

Audi Q7 2006 >

>>>>>>>

YELLOW NOT USED

PURPLE

>>>>>>>>>>

Audi R8

REDBLACKWHITEBLUE

BROWNYELLOW

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Audi TT 2002 > 2006

Remove the audio unit.

Early vehicles may not have CAN at the audio. Connect to Orange / Black & Orange / Brown at the speedo.Software versions before 25.1 will not work on the audio CAN wiring if the factory audio unit is removed.

BLACKWHITEBLUEGREEN

YELLOW

>>>>>>>

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Audi TT 2007 >

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

BMW 1 Series 2004 > 2011

Remove the vehicle speedometer assembly. The CAN wires are located at the connection plug.

CAN HI = ORANGE / GREENCAN LO = GREEN

The CAN wiring can also be located at the audio unit Quadlock.

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

CAN LO = GREEN

locate the FEM (Forward Electrical Module) near the 'A' pillar.

BMW 1 Series (F20) 2011 >

Remove the lower passenger under glove box trim.

BLACKWHITEBLUEGREEN

YELLOW

The CAN bus wiring is a twisted pair of wires, located in the centre white plug loom.

Connect via a 5 Amp fuse to a SWITCHED 12V supply.BLACK Connect to a good chassis ground point.WHITE CAN HI Connection : Vehicle CAN HI wire

>>>>>>>

FPS Disable : 0v Output - Disabled when Reverse is selected.

>>>>>>>>>>

BMW 3 Series (E36) > 2004

CAN HI = YELLOW / BLACKCAN LO = YELLOW / BROWN

Remove the vehicle speedometer assembly. The CAN wires are located at the connection plugs.

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

>>>>>>>>>>

BMW 3 Series (E90) 2005 >

CAN HI = GREEN / ORANGECAN LO = GREEN

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

>>>>>>>>>>

The CAN bus wiring is a twisted pair of wires, located in the centre white plug loom.

YELLOW

BLUEGREEN

REDBLACKWHITE

BMW 3 Series (F30) 2011 >

Remove the lower passenger under glove box trim.

locate the FEM (Forward Electrical Module) near the 'A' pillar.

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

BMW 5 Series (E60) 2003 >

CAN HI = BLACKCAN LO = YELLOW

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

>>>>>>>>>>

bar that runs above the plastic dash pocket. Look up under the drivers side dash to find the loom.

BMW 5 Series (F10-F20) 2010 >

Remove the drivers side lower dash trim. The CAN wires are located in a loom under the chassis

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

BMW 6 Series (2004>)

CAN HI = BLACKCAN LO = YELLOW

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

BMW 7 Series (E65/6) 2001 >

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

>>>>>>>>>>

BMW X1 (E84) 2009 >

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

BMW X3 (E83) > 2011

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

BMW X3 (F25) 2011 >

The CAN wiring can also be located at the audio unit Quadlock and in looms behind the glovebox.

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

>>>>>>>>>>

BMW X5 2008 >

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

BMW X6 2008 >

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

>>>>>>>>>>

BMW Z4 (E85) 2003 >

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

>>>>>>>>>>

BMW Z4 (E89) 2009 >

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

BMW Mini > 2006

Remove the Rev Counter assembly. The CAN wires are located at the connection plug.

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

CAN LO = GREEN

The CAN wiring is present at the rear of the audio unit or rev counter assembly.

BMW Mini 2007 >

BLACKWHITEBLUEGREEN

YELLOW

>>>>>>>

>>>>>>>>>>

>>>WHITE CAN HI Connection : Vehicle CAN HI wire

WHITEBLUEGREENPURPLEORANGEPINK

RED Connect via a 5 Amp fuse to a permanent 12V supply.BLACK

Buick Enclave

CAN HI = OBD Pin 1CAN LO = GROUND (OBD Pin 4)

>>>>>>>

no CAN activity has been detected. Check all electrical connections are sound and that the interface CAN HI and CAN LO connections are the correct way around. Also check that there is

If the LED fails to illuminate or flash, the interface wiring has been connected incorrectley or

Reverse Engaged Output : 12v when reverse gear is selected.YELLOW NOT USED

PINK FPS Disable : 0v Output - Disabled when Reverse is selected.BROWN

>>>>>>>>>>

Chevrolet Aveo : 2011 >

CAN HI = OBD Pin 1CAN LO = Connect to Ground (0v)

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

Unclip the socket for access. The CAN bus wiring is detailed as below:

>>>>>>>

>>>>>>>>>>

Chevrolet Camaro : 2009 >

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Chevrolet Captiva : 2007 >

CAN HI = OBD Pin 1CAN LO = OBD Pin 4 (Ground)

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

Unscrew the socket for access. The CAN bus wiring is a twisted pair of wires, coloured as below:

>>>>>>>

>>>>>>>>>>

Chevrolet Colorado : 2007 >

CAN HI = Pin 6 CAN LO = Pin 14

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

>>>>>>>>>>

Chevrolet Cruze : 2010 >

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

>>>>>>>>>>

Chevrolet Escalade : 2007 >

CAN HI = BEIGE / BLACK (Pin 6)CAN LO = BEIGE (Pin 14)

>>>>>>>

>>>>>>>>>>

Chevrolet HHR : 2006 >

CAN HI = Pin 1CAN LO = Pin 4

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

Unscrew the socket for access. The CAN bus wiring is detailed as below:

>>>>>>>

>>>>>>>>>>

CAN HI = OBD Pin 6CAN LO = OBD Pin 14

Chevrolet Malibu : 2008 >

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

CAN HI = OBD Pin 1CAN LO = Connect to Ground (0v) OBD Pin 4

Chevrolet Orlando : 2010 >

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

CAN HI = OBD Pin 1CAN LO = OBD Pin 4 (Ground)

Chevrolet Silverado : 2007 >

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Chevrolet Spark : 2010 >

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

Unscrew the socket for access. The CAN bus wiring is a twisted pair of wires, detailed as below:

>>>>>>>

>>>>>>>>>>

Chevrolet Volt

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

Unclip the socket for access. The CAN bus wiring is a twisted pair of wires, detailed as below:

>>>>>>>

>>>>>>>>>>

Chrysler 300 C < 2011

CAN HI = WHITE / ORANGECAN LO = WHITE (Possibly White / Red)

The CAN wiring is located at the radio wiring connector.

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

Remove the dash facia panel (clipped) and unbolt the radio for access.

>>>>>>>

>>>>>>>>>>

Also located in the main loom behind the drivers side lower dash panel.

Chrysler 300 C 2012>

CAN HI = GREENCAN LO = WHITE

The CAN wiring is located at the LCD screen connector.

The CAN wiring is not twisted at the plug but may be twisted further in to the loom.

>>>>>>>

>>>>>>>>>>

Also available behind the drivers side kick panel.

CAN HI = WHITE / GREYCAN LO = WHITE / ORANGE

The CAN wiring is located at the radio wiring connector and behind the climate control.

Grand Cherokee 2005 >

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Grand Cherokee 2010 >

CAN HI = WHITE / ORANGECAN LO = WHITE / GREY

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

Also available behind the drivers side kick panel.

>>>>>>>

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Jeep Cherokee

PLEASE NOTE (Before 2007) : ONLY VEHICLES WITH MERCEDES DIESEL ENGINES HAVE CAN WIRING

CAN LO = WHITE / BLUE Models After 2007 CAN HI = WHITE / ORANGE (Radio or O/S Door Loom) CAN LO = WHITE / GREY

The CAN wiring is located at the Engine ECU : N/S Engine bay area main loom near bulk head.

Models Before 2007 CAN HI = WHITE / GREEN (ECU Loom)

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

CAN HI = WHITE / ORANGECAN LO = WHITE

Jeep Wrangler

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Citroen Berlingo > 2007

Locate the BSI module at the rear of the fuse box - drivers side dash.

Carefully pull the BSI board as far forward as possible and remove the plugs for easier access.CAN HI = GREEN

CAN LO = BROWN

The CAN bus wiring is a twisted pair of wires at the back - right hand plug, coloured as below:

The CAN wiring is at the very back corner of the BSI (40 Way Black plug) and is akward to access.

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

PLEASE NOTE : This vehicle has similar wiring as below which are not CAN wires.

>>>>>>>

>>>>>>>>>>

Citroen Berlingo 2008 >

The CAN wiring is located at the audio Quadlok connector, at the rear of the audio unit.

CAN HI = Pin 10 at the audio Quadolk or Pin 6 at the OBD socketCAN LO = Pin 13 at the audio Quadlok or Pin 14 at the OBD socket

If the vehicle does not have CAN wiring at the audio unit, an alternative CAN Bus is present at the

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

OBD socket. The CAN Bus wiring is a twisted pair of wires detailed as below

>>>>>>>

>>>>>>>>>>

No definitive installation is available for this vehicle at present.

YELLOW

BLUEGREEN

REDBLACKWHITE

Citroen C-Crosser

Please refer to the Mitsubishi Outlander information for comparison.

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Citroen C2

>>>>>>>

>>>>>>>>>>

Citroen C3

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

>>>>>>>>>>

Citroen C4

CAN HI = Pin 10 at the audio Quadolk or BLUE (Pin 6 at the OBD socket)CAN LO = Pin 13 at the audio Quadlok or RED (Pin 14 at the OBD socket)

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

>>>>>>>>>>

The CAN bus wiring is a twisted pair of wires, detailed as below:

Citroen C5 2005 >

CAN HI = Quadlock Pin 10CAN LO = Quadlock Pin 13

The CAN wiring is located at the audio Quadlock connector.

>>>>>>>

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Citroen C8

The CAN wiring is located at the OBD socket, inside the lower centre dash pocket.

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

The CAN bus wiring is a twisted pair of wires detailed as below:

YELLOW

BLUEGREEN

REDBLACKWHITE

Citroen Dispatch 2007 >

Remove the audio unit to access the audio connection plugs.

CAN HI = WHITE (Radio) or Pin 6 (OBD Socket)CAN LO = GREY (Radio) or Pin 14 (OBD Socket)

Alternatively, the CAN wires can be located at the OBD socket - lower drivers side dash.

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Citroen DS3

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Citroen DS4

The interface can also be connected at the OBD socket, behind the lower centre dash trim panel.

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

The CAN Bus wiring is a twisted pair of wires detailed as below

>>>>>>>

>>>>>>>>>>

The CAN Bus wiring is a twisted pair of wires detailed as below

The interface can also be connected at the OBD socket, in the bottom of the rear centre console.

Citroen DS5

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Citroen Nemo 2008 >

CAN HI = BLUE (Radio) OR Pin 6 (OBD Socket)CAN LO = WHITE (Radio) OR Pin 14 (OBD Socket)

Alternatively, the CAN wires can be located at the OBD socket : Near Fuse Box - drivers side dash.

BLACKWHITEBLUEGREEN

YELLOW

The CAN bus wiring is detailed as below:

>>>>>>>

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Citroen Picasso

CAN HI = BROWNCAN LO = PURPLE

The CAN wiring is located in the R/H loom behind the glove box. Remove the glove box for access.

Left Hand Drive vehicles, the wiring is in the loom near the fusebox- drivers side dash.

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

YELLOW

REDBLACKWHITE

Dacia Duster

CAN HI = Pin 6 (OBD Socket)CAN LO = Pin 14 (OBD Socket)

The CAN wires can be located at the OBD socket : Inside the glove compartment.

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Dacia Lodgy

The CAN wires can be located at the OBD socket : Lower drivers side dash.

BLACKWHITEBLUEGREEN

YELLOW

>>>>>>>

>>>>>>>>>>

The CAN bus wiring is a twisted pair of wires coloured as below:

YELLOW

BLUEGREEN

REDBLACKWHITE

DAF General J-1939

CAN HI = BLUECAN LO = YELLOW

The CAN wires are located under the N/S lower dash trim, in a loom running left to right.

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Dodge Caliber

CAN HI = WHITE / ORANGECAN LO = WHITE or WHITE / PURPLE

Also located in the main loom behind the drivers side lower dash kick panel.

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

>>>>>>>>>>

Dodge Caravan

>>>>>>>

>>>>>>>>>>

Dodge Challenger < 2011

>>>>>>>

>>>>>>>>>>

Dodge Challenger 2012>

The CAN wiring is located at the LCD screen connector.

The CAN wiring is not twisted at the plug but may be twisted further in to the loom.

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

>>>>>>>>>>

Dodge Durango

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

>>>>>>>>>>

Dodge RAM

>>>>>>>

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Ferrari F430 : 2006 >

CAN HI = PIN 6CAN LO = PIN 14

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Fiat Bravo 2007 >

CAN LO = PIN 14 (Pink / White)

CAN HI = PIN 6 (Pink / Black)

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

>>>>>>>>>>

CAN LO = PIN 14 (Pink / White - Unconfirmed) or 'CAN A' at the radio.

Fiat Croma

CAN HI = PIN 6 (Pink / Black - Unconfirmed) or 'CAN B' at the radio.

BLACKWHITEBLUEGREEN

YELLOW

CAN wiring is also available at the radio. The wire location details are on the Pin-Out diagram

>>>>>>>

>>>>>>>>>>

Fiat Doblo : > 2011

CAN HI = PIN 6 (Pink / Black - Unconfirmed) or 'CAN B' at the radio.CAN LO = PIN 14 (Pink / White - Unconfirmed) or 'CAN A' at the radio.

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

>>>>>>>>>>

CAN LO = PIN 4 OBD Socket

Fiat Doblo : 2012 >

CAN HI = PIN 1 OBD Socket

BLACKWHITEBLUEGREEN

YELLOW

Connection may also be possible at the rear of the radio - no details at present.

>>>>>>>

>>>>>>>>>>

CAN wiring may also be available at the radio. The wire location details are on the Pin-Out diagram

Fiat Ducato 2006 >

The CAN wiring is located at the rear of the OBD socket, drivers dash fuse box behind dash panel.

CAN HI = 'CAN B' at the radio.CAN LO = 'CAN A' at the radio.

>>>>>>>

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Fiat Fiorino : 2008 >

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Connection may also be possible at the rear of the radio - no details at present.

YELLOW

BLUEGREEN

REDBLACKWHITE

Fiat Freemont : 2012 >

CAN HI = PIN 3 OBD SocketCAN LO = PIN 11 OBD Socket

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Fiat Grande Punto

CAN LO = PIN 14 (Pink / White)

CAN HI = PIN 6 (Pink / Black)

>>>>>>>

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Fiat Panda

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Fiat Scudo 2007 >

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Fiat Stilo

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Fiat 500

The CAN wiring is located at the OBD socket, drivers dash behind dash panel.

CAN HI = PIN 6 OBD Socket OR BLUE Wire at the speedometer / audio unitCAN LO = PIN 14 OBD Socket OR WHITE Wire at the speedometer / audio unit.

The CAN Bus can also be located at the rear of the speedometer or audio unit

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

>>>>>>>>>>

YELLOW

REDBLACKWHITE

Ford B-Max 2012 >

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Ford Escape (USA) : 2008 >

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Ford F150 / F250

BLACKWHITEBLUEGREEN

YELLOW

>>>>>>>

>>>>>>>>>>

YELLOW

REDBLACKWHITE

Ford F350 2006 >

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Ford F350 2011 >

BLACKWHITEBLUEGREEN

YELLOW

>>>>>>>

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Ford Fiesta >2007

CAN Bus Option 2 (RPM Applications) : CAN HI = Pin 6 CAN LO = Pin 14Connect to Pins 6 & 14 for installations that require an RPM output.

***Early Fiesta models may not feature this CAN Bus system.

The CAN wiring is located at the OBD socket, lower drivers side dash and at the audio Quadlok***

***CAN Bus Option 1 (Non RPM) : CAN HI = Quadlock Pin 9 CAN LO = Quadlok Pin 10

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Ford Fiesta 2008 >

The CAN wiring is located at the OBD socket, lower drivers side dash and at the radio Quadlock***

Radio Connection : CAN HI = Quadlock Pin 9 CAN LO = Quadlok Pin 10

BLACKWHITEBLUEGREEN

YELLOW

OBD Connection : CAN HI = OBD Pin 3 CAN LO = OBD Pin 11

>>>>>>>

>>>>>>>>>>

Ford Focus & C-Max : 2005 >

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

>>>>>>>>>>

Ford Focus & C-Max : 2011

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Ford Fusion

CAN HI = GREY / REDCAN LO = BLUE / RED

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

CAN LO = OBD Pin 11

Ford Fusion (USA) : 2010 >

CAN HI = OBD Pin 3

BLACKWHITEBLUEGREEN

YELLOW

>>>>>>>

>>>>>>>>>>

Ford Galaxy : 2006 >

The CAN wiring is located at the OBD socket, under the drivers side dash. Unclip the socket to access.

CAN HI = Quadlock Pin 11 - Blue / Grey (or OBD PIN 1)CAN LO = Quadlock Pin 10 - Purple / Grey (or OBD PIN 8)

Note : RPM is only available on the High Speed CAN Bus : Hi = OBD Pin 6 - LO = OBD Pin 14

The CAN wiring can also be accessed at the audio unit Quadlock connector.

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

The CAN wiring is a twisted pair of wiresa coloured as below:

>>>>>>>

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Ford KA 2008 >

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Ford Kuga 2009 >

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Ford Mondeo 2004 >

The CAN wiring is also present at the audio unit Quadlock connector.

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

>>>>>>>>>>

Ford Mondeo 2007 >

CAN HI = Quadlock Pin 11 - Blue / Grey (or OBD PIN 1)CAN LO = Quadlock Pin 10 - Purple / Grey (or OBD PIN 8)

>>>>>>>

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Ford Mustang

CAN HI = WHITE / REDCAN LO = PINK / RED

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

GREENIgnition On Output : 12v when ignition is switched on.Lights On Output : 12v when side / head lights are on.Parking Brake On Output : 0v (Ground) with parking brake on.

PURPLEORANGEPINK

Speed Signal Output : 12v pulsing 1Hz = 1MPH (approx).

Ford Ranger 2012 >

>>>>>>>>>>

Ford Focus S- Max

The CAN wiring is located at the OBD socket, inside the drivers side dash pocket.

CAN Bus Option 1 (Non RPM) : CAN HI = Pin 3 CAN LO = Pin 11CAN Bus Option 2 (RPM Applications) : CAN HI = Pin 6 CAN LO = Pin 14

CAN wiring is also present at the radio Quadlock

Connect to pins 3 & 11 for installations that do not need an RPM output.

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

Connect to Pins 6 & 14 for installations that require an RPM output.

>>>>>>>

>>>>>>>>>>

Ford Transit 2006 >

CAN LO = PURPLE / GREY (Audio Quadlock Pin 10) OR WHITE (OBD PIN 14)The CAN bus wiring can also be located at the OBD socket, drivers side lower dash area.

Remove the vehicle audio unit or speedo or connect at the OBD socket below the drivers side dash.

CAN HI = BLUE / GREY (Audio Quadlock Pin 9) OR WHITE / BLUE (OBD PIN 6)

>>>>>>>

>>>>>>>>>>

Ford Transit Connect 2006 >

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

>>>>>>>>>>

CAN HI = PIN 1 - OBD SocketCAN LO = 0v (Ground)

The CAN wiring is located at the OBD socket, under the drivers side dash or centre console.

GM Single Wire CAN

Available on NAV software issues from 25.6 and PARK from 24.6 and onward.

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

GMC Canyon 2007 >

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

GMC Yukon Denali 2007 >

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

>>>>>>>>>>

The CAN bus wiring is a twisted pair of wires, usually found at the rear of the speedometer or at

J1939 Applications

CAN HI = Vehicle dependent (see individual manufacturer files if available.)CAN LO = Vehicle dependent (see individual manufacturer files if available.)

This profile is available to all vehicles using J1939 CAN information.

the main electrical fuse / relay assembly.

>>>>>>>

>>>>>>>>>>

Honda Accord

CAN HI = WHITECAN LO = RED

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

>>>>>>>>>>

Honda Civic (2006 >)

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

>>>>>>>>>>

Honda Crossroad

CAN HI = WHITE - Pin 2 - Speedo plug OR Pin 6 - OBD SocketCAN LO = RED- Pin 3 - Speedo plug OR Pin 14 OBD Socket

Locate the CAN Bus wiring at the rear of the vehicle speedometer or at the OBD socket.

BLACKWHITEBLUEGREEN

YELLOW

The OBD socket is located at the lower drivers side dash.

>>>>>>>

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Honda CR-V 2007 >

CAN HI = WHITE (Speedo Plug) or Pin 6 (OBD Socket)CAN LO = RED (Speedo Plug) or Pin 14 (OBD Socket)

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

CAN LO = Pin 14 (OBD Socket)

The CAN wires are located at the OBD socket - lower drivers side dash.

Honda CR-V 2012 >

CAN HI = Pin 6 (OBD Socket)

BLACKWHITEBLUEGREEN

YELLOW

>>>>>>>

>>>>>>>>>>

CAN LO = Pin 14 (OBD Socket)

The CAN wires can be located at the OBD socket - lower drivers side dash.

Honda CR-Z 2010 >

CAN HI = Pin 6 (OBD Socket)

BLACKWHITEBLUEGREEN

YELLOW

>>>>>>>

>>>>>>>>>>

Honda Element

>>>>>>>

>>>>>>>>>>

YELLOW

REDBLACKWHITE

Honda Freed 2008 >

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Honda FR-V 2006 >

BLACKWHITEBLUEGREEN

YELLOW

>>>>>>>

>>>>>>>>>>

YELLOW

REDBLACKWHITE

Honda Insight 2009 >

The CAN wires can be located at the OBD socket - lower drivers side dash or at the speedometer.

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Honda Jazz 2009 >

The CAN wires can be located at the OBD socket - lower drivers side dash or at the speedometer.

BLACKWHITEBLUEGREEN

YELLOW

>>>>>>>

>>>>>>>>>>

The OBD socket is located at the lower drivers side dash.

YELLOW

BLUEGREEN

REDBLACKWHITE

Honda Odyssey 2004 >

CAN HI = WHITE - Pin 6- Large Green Speedo plug OR Pin 6 - OBD SocketCAN LO = RED- Pin 7 - Large Green Speedo plug OR Pin 14 OBD Socket

Locate the CAN Bus wiring at the rear of the vehicle speedometer or at the OBD socket.

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Hummer H2 : 2007 >

CAN HI = BROWN / BLACK (Pin 6)CAN LO = BROWN (Pin 14)

>>>>>>>

>>>>>>>>>>

CAN LO = OBD Socket - PIN 14

Hyundai i-10Vehicle CAN Bus Location

CAN HI = OBD Socket - PIN 6

BLACKWHITEBLUEGREEN

YELLOW

>>>>>>>

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

CAN HI = OBD Socket - PIN 6CAN LO = OBD Socket - PIN 14

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

BLACKWHITEBLUEGREEN

YELLOW

>>>>>>>

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Hyundai ix-35Vehicle CAN Bus Location

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Hyundai VelosterVehicle CAN Bus Location

BLACKWHITEBLUEGREEN

YELLOW

>>>>>>>

>>>>>>>>>>

Hyundai H1-i800-iLoad

BLACKWHITEBLUEGREEN

YELLOW

>>>>>>>

>>>>>>>>>>

Infinity FX35

BLACKWHITEBLUEGREEN

YELLOW

>>>>>>>

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Infinity FX45

CAN HI = BLUE (Pin 6)CAN LO = RED (Pin 14)

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Isuzu D-Max : 2012 >

The CAN wires can be located at the OBD socket under the drivers side dash.

BLACKWHITEBLUEGREEN

YELLOW

>>>>>>>

>>>>>>>>>>

Iveco Daily : 2006 >

CAN HI = Wire marked 'CAN B' at the radio.CAN LO = Wire marked 'CAN A' at the radio.

The CAN Bus wiring is located at the radio ISO connectros.

BLACKWHITEBLUEGREEN

YELLOW

Please refer to the PIN OUT diagram on the radio for confirmation of locations.

>>>>>>>

>>>>>>>>>>

Jaguar S-Type 2004 >

>>>>>>>

>>>>>>>>>>

Jaguar X-Type

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

>>>>>>>>>>

The CAN wiring is located at the OBD socket, under the drivers side dash, near the kick panel.

Jaguar XF 2008>

BLACKWHITEBLUEGREEN

YELLOW

>>>>>>>

>>>>>>>>>>

Jaguar XJ6-XJ8

CAN HI = YELLOW (PIN 6)CAN LO = GREEN (PIN 14)

The CAN wiring is located at the OBD socket, under the drivers side dash, near centre console.

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

>>>>>>>>>>

Jaguar XK-R >2007

BLACKWHITEBLUEGREEN

YELLOW

>>>>>>>

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Jaguar XK-R 2008>

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Kia CarensVehicle CAN Bus Location

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Kia CeedVehicle CAN Bus Location

BLACKWHITEBLUEGREEN

YELLOW

>>>>>>>

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Kia Picanto : 2011 >

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Kia Sorento 2009 >Vehicle CAN Bus Location

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Kia SoulVehicle CAN Bus Location

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Kia Sportage 2010 >Vehicle CAN Bus Location

BLACKWHITEBLUEGREEN

YELLOW

>>>>>>>

>>>>>>>>>>

Kia VengaVehicle CAN Bus Location

BLACKWHITEBLUEGREEN

YELLOW

>>>>>>>

>>>>>>>>>>

ORANGEPINK

Lamborghini Galardo

Vehicle CAN Bus LocationRemove the lower passenger side under panel. The CAN wires are located at the loom near fuse board.

>>>>>>>

YELLOW NOT USED

PURPLE

>>>>>>>>>>

Lancia Delta

BLACKWHITEBLUEGREEN

YELLOW

>>>>>>>

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Lancia Musa

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

***Use an OBD connection plug - contact sales for details.

CAN HI = 'CAN B' at the radio OR Pin 6 at the OBD***

Lancia Thesis

CAN LO = 'CAN A' at the radio OR Pin 14 at the OBD***

BLACKWHITEBLUEGREEN

YELLOW

Connection can also be made at the OBD socket, in the fusebox under the drivers dash.

>>>>>>>

>>>>>>>>>>

Lancia Ypsilon

BLACKWHITEBLUEGREEN

YELLOW

>>>>>>>

>>>>>>>>>>

Land Rover Defender 2007>

CAN HI = BLUE / BLACKCAN LO = GREEN / BLACK

>>>>>>>

>>>>>>>>>>

If CAN wires are in positions 3 & 11, use option 1 - otherwise use option 2.

YELLOW

BLUEGREEN

REDBLACKWHITE

Land Rover Discovery 3

CAN LO = PIN 11 Option 2: CAN HI = PIN 6

CAN LO = PIN 14

Locate the OBD socket, lower drivers side dash. The loom can be pulled down for wire access.

Option 1: CAN HI = PIN 3

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

CAN LO = PIN 11

Land Rover Discovery 4

CAN HI = PIN 3

BLACKWHITEBLUEGREEN

YELLOW

The CAN wiring is detailed as below:

>>>>>>>

>>>>>>>>>>

Land Rover Freelander

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

>>>>>>>>>>

Land Rover Freelander 2

CAN HI = Grey / Orange (OBD Pin 3)CAN LO = Purple / Orange (OBD Pin 11)

Locate the OBD socket, lower drivers side dash or connect at the adusio connector.

>>>>>>>

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Land Rover Range Rover

Vehicles from 2005 >

CAN LO = PIN 11Option 2: CAN HI = YELLOW / BLACK - PIN 6

CAN LO = YELLOW / BROWN - PIN 14

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Land Rover Range Rover Sport

CAN LO = PIN 11Option 2: CAN HI = YELLOW / BLACK - PIN 6

CAN LO = YELLOW / BROWN - PIN 14

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

>>>>>>>>>>

Lexus is250Vehicle CAN Bus Location

CAN HI = OBD PIN 6CAN LO = OBD PIN 14

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

>>>>>>>>>>

Lexus RX350 2009 >Vehicle CAN Bus Location

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Lexus RX400-450H 2009 >

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

>>>>>>>>>>

Lincoln Town Car

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

MAN - General J1939

CAN HI = BLUE / REDCAN LO = BLUE / WHITE

The CAN wires are located at the near side, on the top of an ECU in a White connector.

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Unclip the socket for access. The CAN bus wiring is a twisted pair of wires, identified as below:

The CAN wiring is located at the OBD socket, lower drivers side dash area.

Mazda '2'

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Mazda '3' : 2004 >

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Mazda '5'

Connect the interface to a switched 12v+ supply on this vehicle !!!!

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Mazda '6'

CAN HI = PIN 6 CAN LO = Pin 14

Newer vehicles may also feature a 2nd CAN system:CAN HI = PIN 3 CAN LO = Pin 11

The CAN wiring is located at the OBD socket, lower drivers side dash area.Unclip the socket for access. The CAN bus wiring is a twisted pair of wires, identified as below:

>>>>>>>

PINK FPS Disable : 0v Output - Disabled when Reverse is selected.

>>>>>>>>>>

Mazda CX-5

CAN HI = PIN 3 CAN LO = PIN 11

BLACKWHITEBLUEGREEN

YELLOW

>>>>>>>

>>>>>>>>>>

YELLOW

REDBLACKWHITE

Mazda CX-7

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Mazda CX-9

BLACKWHITEBLUEGREEN

YELLOW

>>>>>>>

>>>>>>>>>>

Mazda Demio 2005 >

CAN HI = PIN 6 (RED at the speedometer)CAN LO = PIN 14 (WHITE at the speedometer)

The CAN wiring is located at the OBD socket, lower drivers side dash or the speedometer wiring.

BLACKWHITEBLUEGREEN

YELLOW

>>>>>>>

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Mazda MPV 2005 >

CAN HI = PIN 6 (Blue / White)CAN LO = PIN 14 (Green / Black)

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Mazda MX-5 2006 >

CAN HI = PIN 6 (Blue / White)CAN LO = PIN 14 (Green / Black)

BLACKWHITEBLUEGREEN

YELLOW

>>>>>>>

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Mazda RX-8

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Mazerati Gran Turismo

CAN HI = BLACK / PINKCAN HI = WHITE / PINK

REDBLACKWHITEBLUE

BROWNYELLOW

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Mercedes A-Class >2004

The CAN wiring is located at the speedometer connection plugs.

CAN HI = WHITE CAN LO = GREEN

Remove the lower drivers side under panel. The speedometer cover retaining screws are beneath.

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Alternative connection : CAN HI = WHITE CAN LO = GREEN

The CAN wires are located at the audio unit and in the main wiring looms.

Mercedes A-Class 2005>

Preferred connection : CAN HI = BROWN / RED CAN LO = BROWN

BLACKWHITEBLUEGREEN

YELLOW

>>>>>>>

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Mercedes A-Class 2012>

Preferred connection : CAN HI = BROWN / RED CAN LO = BROWNAlternative connection : CAN HI = GREEN / WHITE CAN LO = GREEN

The CAN wires are at the audio unit and in the drivers side sill loom (8 Way Black Connector).

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

CAN LO = YELLOW

The CAN wires are located in the right of the fuse box at the lower left below the main power cable.

Mercedes Actros

CAN HI = BLUE

BLACKWHITEBLUEGREEN

YELLOW

The CAN bus wiring is a twisted pair of wires in a Purple connector, coloured as below:

>>>>>>>

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Mercedes Atego

CAN HI = BLUECAN LO = YELLOW

The CAN wires are located in the right of the fuse box in a Grey connector.

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

CAN LO = YELLOW

The CAN wires are located in the right of the fuse box in a Grey connector.

Mercedes Axor

CAN HI = BLUE

BLACKWHITEBLUEGREEN

YELLOW

>>>>>>>

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Mercedes B-Class 2005>

Preferred connection : CAN HI = BROWN / RED CAN LO = BROWNAlternative connection : CAN HI = WHITE CAN LO = GREEN

Check for a CAN Network Junction Connector under the O/S dash.

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Mercedes C - Class

Remove the lower drivers side under panel. Locate the ignition barrel loom or control unit loom.

Preffered Connection : CAN HI = BROWN / RED CAN LO = BROWNOR

CAN HI = GREEN / WHITE CAN LO = GREEN

A choice of 2 Bus systems is available, the wiring is a twisted pair of wires, coloured as below:

BLACKWHITEBLUEGREEN

YELLOW

Important ! Use one Bus or the other, do not cross connect the two Buses!!!

>>>>>>>

>>>>>>>>>>

Also located in the centre console loom - drivers side and other locations.

YELLOW

BLUEGREEN

REDBLACKWHITE

Mercedes C - Class 2007 >

CAN Bus 2: CAN HI = GREEN CAN LO = WHITENote: If Reverse Gear Output is required, use Bus 1 for Manual and Bus 2 for Automatic cars.

Otherwise, connect to Bus 1.

The CAN Bus can be located within the plastic loom channels beneath the drivers side carpet.

CAN Bus 1: CAN HI = BROWN / RED CAN LO = BROWN

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Mercedes CLK

Remove the lower drivers side under panel. The CAN wires are located at the lower wiring loom.

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Mercedes CLS 2004 >

The CAN wires are located at the wiring loom below the steering coloumn.

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

The CAN wires are located at the lower wiring loom behind the carpet near to the park brake.

Mercedes CLS 2011 >

BLACKWHITEBLUEGREEN

YELLOW

>>>>>>>

>>>>>>>>>>

Mercedes E - Class (211)

CAN HI = BROWN / RED CAN LO = BROWN

Remove the lower drivers side under panel. Locate the ignition barrel loom or control unit loom.

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

The wiring is a twisted pair of wires, coloured as below:

>>>>>>>

>>>>>>>>>>

Note: If Reverse Gear Output is required, use Bus 1 for Manual and Bus 2 for Automatic cars.Otherwise, connect to Bus 1.

The CAN Bus wiring is a twisted pair of wires, coloured as below:

Mercedes E - Class (212) 2008 >

Remove the N/S kick panel

CAN Bus 2: CAN HI = GREEN CAN LO = WHITE

BLACKWHITEBLUEGREEN

YELLOW

>>>>>>>

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Mercedes G 1990 >

The CAN wires are located at the ABS module.

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Remove the passenger side kick panel. The CAN wires are located at the lower wiring loom.

Mercedes GL 2006 >

BLACKWHITEBLUEGREEN

YELLOW

>>>>>>>

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Mercedes GLK 2008 >

The CAN wires are located at the lower wiring loom behind the carpet near to the park brake.

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Mercedes M-Class >2005

Remove the lower drivers side under panel. The CAN wires are located at the control module.

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

>>>>>>>>>>

The CAN Bus can be located at the rear of the audio unit.

Mercedes M Class 2006 >

CAN HI = BROWN / RED CAN LO = BROWN

BLACKWHITEBLUEGREEN

YELLOW

Carefully unclip the heater control panel and pull down the 2 metal retaining clips behind to remove.

>>>>>>>

>>>>>>>>>>

Check for a CAN Network Junction Connector under the O/S dash.

Mercedes R-Class 2006>

BLACKWHITEBLUEGREEN

YELLOW

>>>>>>>

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Mercedes S-Class

Remove the lower drivers side under panel. The CAN wires are located at the CAN junction.

CAN Bus 2: CAN HI = GREEN CAN LO = WHITENote: If Reverse Gear Output is required, use Bus 1 for Manual and Bus 2 for Automatic cars.

Otherwise, connect to Bus 1.

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

May also be available at the audio. The CAN bus wiring is a twisted pair of wires coloured as below:

Preferred connection : CAN HI = BROWN / RED CAN LO = BROWNFor PARK products, try this bus first : CAN HI = WHITE CAN LO = GREEN

Remove the vehicle speedometer cover. The CAN wires are located at the connection plugs.

Mercedes SL / K 2004 >

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

CAN HI = GREEN / WHITE CAN LO = GREEN

Mercedes Sprinter > 2006

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Mercedes Sprinter 2007 >

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

May also be available at the audio. The CAN bus wiring is a twisted pair of wires coloured as below:

>>>>>>>

>>>>>>>>>>

Mercedes Viano / Vito

Early models may not have the BROWN CAN Bus

Remove the lower drivers side under panel. The CAN wires are located at near the kick panel.

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

Also at the speedometer. The CAN bus wiring is a twisted pair of wires, coloured as below:

>>>>>>>

>>>>>>>>>>

CAN LO = WHITE

The CAN Bus can be located at the rear of the speedometer or audio unit.

Mitsubishi ASX 2010 >

CAN HI = BLACK

BLACKWHITEBLUEGREEN

YELLOW

>>>>>>>

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Mitsubishi Colt

Remove the lower drivers side dash panel. The CAN wires are located at the OBD Socket.

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Mitsubishi Grandis

CAN HI = OBD Pin 6 (RED / BLUE at speedo - PIN 4 opposite the plug catch)CAN LO = OBD Pin 14 (BLACK / BLUE at speedo - PIN 3 opposite the plug catch)

The CAN wires are located at the OBD Socket - Lower drivers side dash. Also at the rear of speedo

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

The CAN bus wiring is a twisted pair of wires, detailed as below

>>>>>>>

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Mitsubishi Lancer Evo 10 2008>

CAN HI = GREEN CAN LO = PINK

The CAN Bus wiring is located at the rear of the speedometer.

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Mitsubishi L200 (2006>)

This vehicle is not supported after SWV 28.9 - Please contact Technical support.

The CAN wires are located at the OBD Socket, under the drivers side dash.

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

>>>>>>>>>>

The CAN wires are located at the OBD Socket, under the drivers side dash.

Mitsubishi L200 (2012>)

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Mitsubishi Outlander 2007>

CAN HI = GREEN (Behind speedometer) OR ORANGE (Behind radio)CAN LO = PINK (Behind speedometer) OR WHITE (Behind radio)

The CAN Bus wiring is located at the rear of the speedometer and at the audio wiring connector

BLACKWHITEBLUEGREEN

YELLOW

>>>>>>>

>>>>>>>>>>

YELLOW

REDBLACKWHITE

Mitsubishi Outlander 2013 >

The CAN Bus wiring is located at the OBD Connector, under the lower drivers side dash.

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

CAN LO = PIN 14

Nissan 350Z

CAN HI = PIN 6

BLACKWHITEBLUEGREEN

YELLOW

>>>>>>>

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Nissan 370Z

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Nissan Almera

CAN HI = BLUECAN LO = RED

Remove the vehicle speedometer assembly. The CAN wires are located at the large multi plug.

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

CAN LO = Pin 14

Nissan Altima

CAN HI = Pin 6

BLACKWHITEBLUEGREEN

YELLOW

>>>>>>>

>>>>>>>>>>

Nissan Cube

CAN HI = RED or BLUE (late models) or OBD Pin 6CAN LO = WHITE or PINK (late models) or OBD Pin 14

Remove the vehicle speedometer assembly or connect at the OBD socket - drivers side dash.

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

The CAN bus wiring is a twisted pair of wires, coloured as below (later models change colour):

>>>>>>>

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Nissan Elgrand 2002 >

CAN HI = PINK - Pin 4 at Speedo OR Pin 6 at OBD socketCAN LO = BLUE - Pin 5 at speedo OR Pin 14 at OBD Socket

Connect at the rear of the speedometer or at the OBD socket - drivers side lower dash.

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

CAN LO = Pin 14

Nissan Juke 2010 >

CAN HI = Pin 6

BLACKWHITEBLUEGREEN

YELLOW

>>>>>>>

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Nissan Micra

CAN LO = WHITE : Pin 14The CAN wiring is also available at the rear of the speedo in pins 1 & 2.

Unclip both 'A' pillar trims and the dash lid for access to the rear of the speedo.

CAN HI = RED : Pin 6

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Nissan Murano

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Nissan Navarra

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

CAN LO = Pin 14

Nissan Note

CAN HI = Pin 6

BLACKWHITEBLUEGREEN

YELLOW

>>>>>>>

>>>>>>>>>>

CAN LO = Pin 14

Nissan NV 200 2010>

CAN HI = Pin 6

BLACKWHITEBLUEGREEN

YELLOW

>>>>>>>

>>>>>>>>>>

CAN LO = Pin 14

Nissan Pathfinder

CAN HI = Pin 6

BLACKWHITEBLUEGREEN

YELLOW

>>>>>>>

>>>>>>>>>>

CAN LO = Pin 14

Nissan Pixo

CAN HI = Pin 6

BLACKWHITEBLUEGREEN

YELLOW

>>>>>>>

>>>>>>>>>>

CAN LO = OBD Pin 14

The CAN wiring is located at the OBD socket, under the steering column.

Nissan Primastar

CAN HI = OBD Pin 6

BLACKWHITEBLUEGREEN

YELLOW

>>>>>>>

>>>>>>>>>>

Nissan Primera

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Nissan Qashqai

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

CAN LO = Pin 14

Nissan Rogue

CAN HI = Pin 6

BLACKWHITEBLUEGREEN

YELLOW

>>>>>>>

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Nissan Sentra

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Nissan Skyline / 350GT

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Nissan X-trail

CAN HI = WHITECAN LO = RED

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

>>>>>>>>>>

Opel GT : 2007 >

>>>>>>>

>>>>>>>>>>

Peugeot 206 2002 >

CAN LO = PURPLE

The CAN bus wiring is a twisted pair of wires at the coloured as below:

CAN HI = BROWN

BLACKWHITEBLUEGREEN

YELLOW

>>>>>>>

>>>>>>>>>>

at the radio Quadlock. The CAN bus wiring is a twisted pair of wires, coloured as below:

YELLOW

BLUEGREEN

REDBLACKWHITE

Peugeot 207

CAN HI = OBD Pin 6 OR at the Quadlock RED wireCAN LO = OBD Pin 14 OR at the Quadlock : BLUE wire

The CAN wiring is located at the OBD socket under the drivers dash and also

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Peugeot 208 : 2012 >

CAN HI = OBD Pin 6 OR at the Radio Quadlock Pin 10CAN LO = OBD Pin 14 OR at the Radio Quadlock Pin 13

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Peugeot 307 All Models

CAN HI = GREENCAN LO = GREY

Remove the lower passenger side under panel. The CAN wires are located at the BSI module.

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

The CAN bus wiring is a twisted pair of wires on a black multi-plug, coloured as below:

>>>>>>>

>>>>>>>>>>

CAN LO = OBD Pin 14 OR at the Radio Quadlock Pin 13

Peugeot 308 : 2007 >

CAN HI = OBD Pin 6 OR at the Radio Quadlock Pin 10

BLACKWHITEBLUEGREEN

YELLOW

>>>>>>>

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Peugeot 407

CAN HI = WHITECAN LO = GREY

Remove the lower passenger side under panel. The CAN wires are located at a white multi-plug.

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Peugeot 4007

Please refer to the Mitsubishi Outlander infor mation for comparison.

BLACKWHITEBLUEGREEN

YELLOW

No definitive installation is available for this vehicle at present.

>>>>>>>

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Peugeot 508 : 2011 >

CAN HI = OBD Pin 6 OR at the Radio Quadlock Pin 10CAN LO = OBD Pin 14 OR at the Radio Quadlock Pin 13

The CAN wiring is located at the OBD socket under the ashtray and also

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Peugeot 607 : 2000 >

CAN HI = Brown Insert, Pin 1 (Beige wire)CAN LO = Brown Insert, Pin 3 (Red wire)

The CAN wiring is located at the BSI Module (Fuse Box). Locate the Black connector that has

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

Green and Brown inserts. The CAN bus wiring is a twisted pair of wires, coloured as below:

>>>>>>>

>>>>>>>>>>

The CAN wiring is located at the OBD socket, inside the lower centre dash pocket and also

Peugeot 607 : 2005 >

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Peugeot 807 > 2005

CAN HI = WHITECAN LO = PURPLE

The CAN wiring is located in a wiring loom - behind drivers side dash.

>>>>>>>

>>>>>>>>>>

Peugeot 807 2006>

CAN HI = OBD Pin 6 OR at the Quadlock WHITE wireCAN LO = OBD Pin 14 OR at the Quadlock : YELLOW wire

The CAN wiring is located at the OBD socket, inside the lower centre dash pocket and also

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

>>>>>>>>>>

YELLOW

REDBLACKWHITE

Peugeot Bipper : 2008 >

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Peugeot Boxer : 2006 >

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

The CAN bus wiring is a twisted pair of wires detailed as below:

Peugeot Expert 2007 >

CAN HI = WHITE (Radio) or Pin 6 (OBD Socket)CAN LO = GREY (Radio) or Pin 14 (OBD Socket)

>>>>>>>

>>>>>>>>>>

PLEASE NOTE : This vehicle has similar wiring as below which are not CAN wires.

YELLOW

BLUEGREEN

REDBLACKWHITE

Peugeot Partner > 2007

Carefully pull the BSI board as far forward as possible for easier access.CAN HI = GREEN

CAN LO = BROWN

The CAN bus wiring is a twisted pair of wires at the back - right hand plug, coloured as below:

The CAN wiring is at the very back of the BSI and can be akward to access.

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Peugeot Partner 2008 >

>>>>>>>

>>>>>>>>>>

Porsche Boxster > 2004

CAN HI = WHITE / BLUECAN LO = WHITE / GREY

The CAN bus wiring is a twisted pair of wires at the GREEN plug, coloured as below.

to the right of the dash - remove both Torx fixings at the rear of them. Then lift the dash upwards.

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

Remove the Hazard Switch Lens on the left of the dash and also the small round vent type cover

>>>>>>>

>>>>>>>>>>

main loom to the side. The CAN bus wiring is a twisted pair of wires, coloured as below:

The Orange & Purple outputs will switch off when the vehicle park Brake is applied on compatible vehicles

YELLOW

BLUEGREEN

REDBLACKWHITE

Porsche Boxster 2004 >

CAN HI = YELLOWCAN LO = BLACK

Remove the drivers side kick trim which houses the fuse box. The CAN wiring is located in the

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Porsche Cayenne

CAN HI = ORANGE / GREEN CAN LO = ORANGE / BROWN

Locate the main front-to-rear loom behind the drivers side kick panel carpet.

Also may be available in the loom at the rear of the headlamp switch.

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

>>>>>>>>>>

Porsche Cayman

CAN HI = YELLOWCAN LO = BLACK

Remove the drivers side kick trim which houses the fuse box. The CAN wiring is located in the

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

main loom to the side. The CAN bus wiring is a twisted pair of wires, coloured as below:

>>>>>>>

>>>>>>>>>>

Renault Clio

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Renault Espace

The CAN wiring is located at the OBD socket, under a cover between the 2 front seats.

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

The CAN wiring is located at the OBD socket, under the cup holder in the below the centre arm rest.

Renault Fluence 2009 >

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Renault Kangoo 2008 >

The CAN wiring is located at the OBD socket, in the centre console, under a trim cover.

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

>>>>>>>>>>

The CAN wiring is located at the OBD socket, in the fuse compartment (passenger dash area).

Renault Kangoo 2003 >

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Renault Koleos

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

The CAN wiring is located at the OBD socket, under a rubber cover below the ashtray.

Renault Laguna > 2007

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Renault Laguna 2008 >

The CAN wiring is located at the OBD socket, under the cup holder in the below the centre arm rest.

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

>>>>>>>>>>

Renault Master > 2008

The CAN wiring is located at the OBD socket, behind the drivers side lower dash panel.

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

>>>>>>>>>>

The CAN wiring is located at the OBD socket, inside the glove compartment.

Renault Master 2009 >

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

CAN HI = PINKCAN LO = BROWN / WHITE

Renault Megane > 2008

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Renault Megane 3 : 2009 >

The CAN wiring is located at the OBD socket, under the radio behind a plastic panel.

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

>>>>>>>>>>

Renault Modus

CAN HI = ORANGECAN LO = BROWN

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

>>>>>>>>>>

Also available at the OBD connector, under a cover between the front seats.

YELLOW

BLUEGREEN

REDBLACKWHITE

Renault Scenic 2003>

CAN HI = BROWN / WHITE Or OBD Pin 6CAN LO = ORANGE / WHITE or OBD Pin 14

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

The CAN wiring is located at the OBD socket, under the centre console - slide back to access.

Renault Scenic : 2009 >

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Renault Traffic

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Renault Vel Satis 2002 >

The CAN wiring is located at the OBD socket, under a rubber cover below the ashtray.

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

>>>>>>>>>>

The CAN wiring is located at the OBD socket in the glove box.

Renault Wind : 2010 >

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Rover 75 / MG-ZT(T)

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

>>>>>>>>>>

Rover 75 (V8 Engine)

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

>>>>>>>>>>

Saab 93 2006 >

CAN LO = Pin 4 (Ground Connection)Alternative connection : CAN HI = Pin 6

Alternative connection : CAN LO = Pin 14

Locate the OBD socket under the drivers side dash area.

CAN HI = Pin 1 (Single wire CAN)

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

Connect the interface as below

>>>>>>>

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Saab 95 : 2006 >

Remove the vehicle Glove Box. The CAN wires are located at the Left Hand Main Loom.

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

CAN LO = OBD Pin 4 (Black)

Remove the vehicle Glove Box. The CAN wires are located at the Left Hand Main Loom.

Saab 95 : 2010 >

CAN HI = OBD Pin 1 (Green)

BLACKWHITEBLUEGREEN

YELLOW

>>>>>>>

>>>>>>>>>>

Scania General J-1939

CAN HI = YELLOWCAN LO = WHITE

The CAN wiring can be found in the main loom under the passenger fuse box and also at

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

the speedometer assembly. The CAN bus wiring is a twisted pair of wires, coloured as below:

>>>>>>>

>>>>>>>>>>

Seat Alhambra

The CAN wires are located at the GREEN connector located at the rear of the speedometer. Remove the steering

CAN HI = ORANGE / BLACK CAN LO = ORANGE / BROWNLater models may also feature the CAN wiring at the radio (top ISO connector):-

column housing. There are 2 x Torx screws securing the speedometer. Remove these and insert a plastic lever tool at

connection plug - only one set carries the CAN data! The CAN wiring is a twisted pair coloured as below :-

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

the top edge of the speedometer glass. Lever the speedo forward to release. There are 2 sets of CAN wiring at the

>>>>>>>

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Seat Altea > 2007

CAN HI = YELLOWCAN LO = BROWN

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Seat Altea 2008 >

Remove the lower drivers side under panel. The CAN wires are located at a 12 way multi-plug.

Under Dash : CAN HI = ORANGE / GREEN Radio : CAN HI = ORANGE / PURPLE Under Dash : CAN LO = ORANGE / BROWN Radio : CAN LO = ORANGE / BROWN

The CAN wires can also be located at the rear of the audio unit.

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

>>>>>>>>>>

Seat Exeo 2009 >

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

>>>>>>>>>>

Seat Ibiza 2003 >

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Seat Leon 2005 >

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Skoda Fabia

Remove the speedometer assembly. The CAN wires are located at the wiring plug.

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Skoda Octavia 05 >

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

>>>>>>>>>>

CAN LO = ORANGE / BROWNThe CAN wiring may also be present in other looms at the front and back of the car.

* Connection can also be made at the audio connector - the HI wire will be ORANGE / PURPLE

CAN HI = ORANGE / GREEN *

Skoda Octavia II 09 >

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Skoda Roomster 09 >

* When connecting in other looms the HI wire may be ORANGE / GREEN

CAN HI = ORANGE / PURPLE *

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

>>>>>>>>>>

Skoda Superb 08 >

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Skoda Yeti 09 >

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

>>>>>>>>>>

Smart Car > 2006

CAN HI = BROWN / REDCAN LO = WHITE / BLACK

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

The CAN wiring can also be accessed in the loom towards the speedo, under the drivers dash area.

>>>>>>>

>>>>>>>>>>

vertical towards the heater panel at the top of the dash. Also available at the OBD Socket.

Smart Fourtwo 2007>

CAN HI = GREEN / WHITE OR OBD Pin 6CAN LO = GREEN OR OBD Pin 14

Remove the vehicle audio unit. The CAN wires are located in the loom running.

>>>>>>>

>>>>>>>>>>

YELLOW

REDBLACKWHITE

Subaru Forester 2009 >

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Subaru Impreza 2008 >

BLACKWHITEBLUEGREEN

YELLOW

>>>>>>>

>>>>>>>>>>

YELLOW

REDBLACKWHITE

Subaru Legacy 2004 >

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

YELLOW

REDBLACKWHITE

Subaru Outback 2003 >

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Subaru XV 2012 >

BLACKWHITEBLUEGREEN

YELLOW

>>>>>>>

>>>>>>>>>>

YELLOW

REDBLACKWHITE

Suzuki Alto

The CAN wiring is located at the OBD socket, near the centre console under drivers side dash.

Unclip the socket for access.

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Suzuki Grand Vitara

CAN HI = OBD Socket - Pin 6 OR RED wire at the speedometer multi-plug.CAN LO = OBD Socket - Pin 14 OR WHITE wire at the speedometer multi-plug.

Unclip the socket for access. Alternatively, the CAN wiring is also located at the speedometer

BLACKWHITEBLUEGREEN

YELLOW

multi-plug, in pins 8 and 10. The CAN bus wiring is a twisted pair of wires, coloured as below:

>>>>>>>

>>>>>>>>>>

YELLOW

REDBLACKWHITE

Suzuki Splash

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

YELLOW

REDBLACKWHITE

Suzuki Swift 2006 >

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Suzuki SX4

BLACKWHITEBLUEGREEN

YELLOW

>>>>>>>

>>>>>>>>>>

CAN LO = OBD Socket - Pin 14

Toyota Avensis (2009 >)

CAN HI = OBD Socket - Pin 6

BLACKWHITEBLUEGREEN

YELLOW

>>>>>>>

>>>>>>>>>>

Toyota BB 2006 >

CAN HI = OBD Socket - Pin 6 OR BLACK wire at the speedometer multi-plug.CAN LO = OBD Socket - Pin 14 OR WHITE wire at the speedometer multi-plug.

BLACKWHITEBLUEGREEN

YELLOW

>>>>>>>

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Toyota Estima 2006 >

CAN HI = OBD Socket - Pin 6 OR BLACK wire at the speedometer multi-plug.CAN LO = OBD Socket - Pin 14 OR WHITE wire at the speedometer multi-plug.

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

YELLOW

WHITEBLUEGREEN

REDBLACK

Toyota GT86 : 2012 >

>>>>>>>

Speed Dependent Output : 12v between speeds of 1 to 6 MPHPINK

ORANGEFPS Disable : 0v Output - Disabled when Reverse is selected.

>>>>>>>>>>

The CAN wiring is located at the OBD socket, under the drivers side dash.Unclip the socket for access. The CAN bus wiring is a twisted pair of wires, detailed as below:

Toyota Hi-Lux : 2008 >

Please note that only the PARK range of products are compatible with this vehicle model.

BLACKWHITEBLUEGREEN

YELLOW

>>>>>>>

ORANGE Speed Dependent Output : 12v between speeds of 1 to 6 MPHPINKBROWN Reverse Engaged Output : 12v when reverse gear is selected.YELLOW NOT USED

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Toyota iQ : 2009 >

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Toyota Land Cruiser 2009 >

BLACKWHITEBLUEGREEN

YELLOW

>>>>>>>

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Toyota Prius : 2005 >

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Toyota Prius : 2009 >

BLACKWHITEBLUEGREEN

YELLOW

>>>>>>>

>>>>>>>>>>

Toyota RAV 4 2006 >

CAN HI = OBD Socket - Pin 6 OR DARK GREEN wire at the speedometer multi-plug.CAN LO = OBD Socket - Pin 14 OR WHITE wire at the speedometer multi-plug.

BLACKWHITEBLUEGREEN

YELLOW

>>>>>>>

>>>>>>>>>>

Toyota Verso S (2011 >)

BLACKWHITEBLUEGREEN

YELLOW

>>>>>>>

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Toyota Yaris (2006 >)

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Toyota Yaris (2011 >)

BLACKWHITEBLUEGREEN

YELLOW

>>>>>>>

>>>>>>>>>>

Vauxhall Agila 2009 >

CAN HI = OBD Pin 6 - Brown / BlackCAN LO = OBD Pin 14 - Brown

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

>>>>>>>>>>

Vauxhall Ampera

>>>>>>>

>>>>>>>>>>

Vauxhall Antara 2007 >

CAN LO = GROUND (OBD Pin 4)

Unclip the socket for access. This vehicle uses 'Single Wire' CAN, connect as below:

CAN HI = OBD Pin 1

>>>>>>>

>>>>>>>>>>

Vauxhall Astra 2005 > 2009

Connect at the OBD socket or at the radio Quadlock

CAN HI = GREEN (PIN 1 at OBD - or GREEN (twisted pair) - Radio Quad lock)CAN LO = BROWN (PIN 4 at OBD - or WHITE (twisted pair) - Radio Quad lock)

The OBD socket is located in the lower, centre dash area.

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

The CAN bus wiring is detailed below:

>>>>>>>

>>>>>>>>>>

Vauxhall Astra 2009 >

CAN HI = OBD Pin 1

>>>>>>>

>>>>>>>>>>

The CAN bus wiring is a twisted pair of wires located at the multiplug, coloured as below:

YELLOW

BLUEGREEN

REDBLACKWHITE

Vauxhall Corsa / Combo >2006

Remove the vehicle speedometer assembly.

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Vauxhall Corsa 2006 >

Connect at the OBD socket or at the radio Quadlock

The OBD socket is located in the lower, centre dash area.

BLACKWHITEBLUEGREEN

YELLOW

The CAN bus wiring is detailed below:

>>>>>>>

>>>>>>>>>>

Vauxhall Insignia

CAN HI = OBD Pin 1

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

>>>>>>>>>>

The CAN bus wiring is a twisted pair of wires located at the multiplug, coloured as below:

YELLOW

BLUEGREEN

REDBLACKWHITE

Vauxhall Meriva 2004 >

Remove the vehicle speedometer assembly.

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Vauxhall Meriva 2010 >

CAN HI = OBD Pin 1

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

>>>>>>>>>>

Vauxhall Mokka 2010 >

CAN HI = OBD Pin 1

>>>>>>>

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Vauxhall Movano > 2008

The CAN wiring is located at the OBD socket, behind the drivers side lower dash panel.

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

CAN LO = PIN 14

The CAN wiring is located at the OBD socket, inside the glove box.

Vauxhall Movano 2009 >

CAN HI = PIN 6

BLACKWHITEBLUEGREEN

YELLOW

>>>>>>>

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Vauxhall Signum

CAN HI = OBD Pin 1

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Vauxhall Vectra

CAN HI = OBD Pin 1

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Vauxhall Vivaro

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

>>>>>>>>>>

Vauxhall Zafira A > 2005

CAN HI = GREEN CAN LO = WHITE

Remove the drivers side kick panel. The CAN wires are located inside a black plastic loom.

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

The CAN bus wiring is a STRAIGHT pair of wires, coloured as below:

>>>>>>>

>>>>>>>>>>

OBD : Remove the ash tray and inner metal plate. Conect at the OBD socket loom.

YELLOW

BLUEGREEN

REDBLACKWHITE

Vauxhall Zafira B 2005 >

CAN HI = GREEN (PIN 1 at OBD)CAN LO = BROWN (PIN 4 at OBD)

Connect at the OBD Socket or at the radio wiring connector.

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

CAN LO = OBD Pin 4

Connect at the OBD Socket or at the radio wiring connector.

Vauxhall Zafira C 2012 >

CAN HI = OBD Pin 1

BLACKWHITEBLUEGREEN

YELLOW

OBD : Remove the ash tray and inner metal plate. Conect at the OBD socket loom.

>>>>>>>

>>>>>>>>>>

loom near the steering column. The CAN may also be available at the audio Quadlock connector.

YELLOW

BLUEGREEN

REDBLACKWHITE

VW Amorak

Remove the lower drivers side under panel. The CAN wires are a twisted pair located in the main

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

VW Beetle

CAN HI = ORANGE / BLACKCAN LO = ORANGE / BROWN

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

VW Caddy : 2004 >

Remove the lower drivers side under panel. The CAN wires are located in the main wiring loom.

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

CAN HI = BROWN / REDCAN LO = BROWN

Remove the drivers side lower dash panel.

VW Crafter

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

YELLOW

REDBLACKWHITE

VW Fox

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

VW Golf V : 2004 >

Remove the lower steering column cover to expose the loom to the wiper / indicator controls.

Some vehicles may also have CAN wiring present at the audio connector.

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

>>>>>>>>>>

VW Golf VI : 2009 >

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

VW Golf VII : 2012 >

CAN HI = ORANGE / GREEN - Also located at Pin 16 (BCM Brown plug - Rear of fuse box)CAN LO = ORANGE / BROWN - Also located at Pin 17 (BCM Brown plug - Rear of fuse box)

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

VW Golf Plus

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Remove the lower drivers side under panel.

VW Jetta 2005 >

BLACKWHITEBLUEGREEN

YELLOW

>>>>>>>

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

VW Passat 02 > 05

CAN HI = ORANGE / BLACKCAN LO = ORANGE / BROWN

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

VW Passat 05 >

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Remove the lower drivers side under panel. The CAN wires are located in the main wiring loom.

VW Passat : 2011 >

BLACKWHITEBLUEGREEN

YELLOW

>>>>>>>

>>>>>>>>>>

VW Polo

CAN HI = ORANGE / PURPLE Note: ORANGE / BLACK 2010 MY Polo

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

>>>>>>>>>>

VW Routan

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

>>>>>>>>>>

YELLOW

REDBLACKWHITE

VW Scirocco

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

the top edge of the speedometer glass. Lever the speedo forward to release. There are 2 sets of CAN wiring at the

YELLOW

BLUEGREEN

REDBLACKWHITE

VW Sharan

The CAN wires are located at the GREEN connector located at the rear of the speedometer. Remove the steering

CAN HI = ORANGE / BLACK CAN LO = ORANGE / BROWNLater models may also feature the CAN wiring at the radio (top ISO connector):-

column housing. There are 2 x Torx screws securing the speedometer. Remove these and insert a plastic lever tool at

connection plug - only one set carries the CAN data! The CAN wiring is a twisted pair coloured as below :-

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

VW Tiguan

BLACKWHITEBLUEGREEN

YELLOW

>>>>>>>

>>>>>>>>>>

VW Touareg : 2003 >

Remove the dash trim to gain access to the rear of the headlamp control switch.

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

The interface is installed to the CAN wiring in the wiring loom behind the switch.

>>>>>>>

>>>>>>>>>>

VW Touareg : 2011 >

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

The interface is installed to the CAN wiring in the steering column loom.

>>>>>>>

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

VW Touran

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

VW Transporter 2003 >

CAN HI = ORANGE / GREEN (Under Dash)CAN LO = ORANGE / BROWN

Remove the lower drivers side under panel. The CAN wires are located at a 18 way black multi-plug.

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

>>>>>>>>>>

VW Transporter 2010 >

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

CAN LO = PIN 14

Volvo C30

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

CAN LO = GREEN

The CAN wires are located under the fuse box in a Green connector.

Volvo General J-1939

CAN HI = YELLOW

BLACKWHITEBLUEGREEN

YELLOW

>>>>>>>

>>>>>>>>>>

Volvo S40 2005 >

CAN LO = PIN 14

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

>>>>>>>>>>

YELLOW

BLUEGREEN

REDBLACKWHITE

Volvo S60

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Volvo V50 2005 >

CAN LO = PIN 14

>>>>>>>

>>>>>>>>>>

CAN LO = PIN 11

CAN HI = PIN 3

Volvo V60 & XC60

>>>>>>>

YELLOW NOT USED

>>>>>>>>>>

Option 1: CAN HI = PIN 3 (White - also at speedo & radio)

Volvo V70 & XC70

Option 2: CAN HI = PIN 6CAN LO = PIN 14

Pre 2004 models - OBD CAN may not be available. Connect behind the speedometer or radio.

CAN LO = PIN 11 (Green - also at speedo & radio)

>>>>>>>

>>>>>>>>>>

Volvo XC90

CAN LO = PIN 14

BLACKWHITEBLUEGREEN

PURPLEORANGEPINK

>>>>>>>

CANM8-NAV Installation File Accura RDX · 2013-12-18 · CANM8-NAV Installation File Accura RDX...

Documents

AD-A016 863 WABASH - RDX MANUFACTURE: A LABORATORY ... · AD-A016 863 WABASH - RDX MANUFACTURE: ... WABASH - RDX MANUFACTURE: A LABORATORY ... the Bachmann process now in use

Accura font family download

Patent Litigation - Accura · DeNMarK Law & Practice Contributed by Accura Advokatpartnerselskab Authors: Jeppe Brinck-Jensen, Anders Poulsen 4 accura advokatpartnerselskab IP team

Rdx 230907

Using RDX® QuikStation® and QuikStor ... - Overland Tandberg · Overland-Tandberg RDX QuikStor drives and QuikStation appliances ... The RDX QuikStation family offers two models

CVA Accura

ACCURA HYDROGRAPHIC RC SURVEY BOAT

Accura Mobile Nitrogen Cart - idaircompressors.com€¦ · Accura Mobile the latest in high performance nitrogen tire inflation. The Accura Mobile is a compact nitrogen tire inflation

Preset Tyre Inflator ACCURA D10 / D20

Appendix E: Material properties - Wohlers Associateswohlersassociates.com/materials2010.pdf · Material Accura Xtreme Plastic Accura 60 Accura 10 Accura 25 Accura 55 ... Material

RDX Pad Print Program

Accura news for publishers

Im-RDX Production

Briot Accura Calibration Manual

Reduced Sensitivity RDX (RS-RDX) Part I: Literature Review and

Ciclotron Rdx 800

ACCURA - mophweb.intouchmena.com Devices/M… · Accura Medizintechnik GmbH Max-Planck-Straße 33 61 194 Karben, Germany Tel +49 6039 92010 Email: info@accuramed.de ACCURA Urqent

RDX Armoury

US Summarize Tool Support 4691 1 Indirect #REF! #REF ......US Acura NSX 2017 US Acura NSX 2018 US Acura RDX 2007 US Acura RDX 2008 US Acura RDX 2009 US Acura RDX 2010 US Acura RDX

ACCURA - Optimus