2.1.1 Glass Panel...5/8/2018 Glass Panel and Attachments → Removal and Installation → Body...

5/8/2018 Glass Panel and Attachments → Removal and Installation → Body Exterior • 2011 Volkswagen Eos • MotoLogic

https://www.motologic.com/car/vw_2011_1f7_eos/article/d5a28f01ab0933e9f56844e14a6f62e8?returnPath=%2Fcar%2Fvw_2011_1f7_eos%2Fsearch%3Fkeywords%

2011 Eos

Report a problem with this article⇒ “2.1.1 Glass Panel”, page 124

⇒ “2.1.2 Glass Panel Cables”, page 131

⇒ “2.1.3 Sunroof Motor”, page 139

⇒ “2.1.4 Glass Panel Seal, from July 2007”, page 142

⇒ “2.1.5 Guide Rails”, page 143

2.1.1 Glass PanelRemoving

♦ Sunshade already removed.♦ All screws are microencapsulated and must always be replaced.♦ Screw tightening torque: 3 Nm.

– Loosen the end eyes -3 and 6- on tensioning bands-2 and 5- on the outside of the main hinge.

– Remove tensioned headliner without loosening additional ten‐sioning bands. Refer to⇒ “2.6.6 Tensioned Headliner, Removing”, page 248

– Remove tensioned headliner rail. Refer to⇒ “2.6.13 Tensioned Headliner Rail, Removing”, page 261 .

♦ When the luggage compartment trim is installed, make sure the support is not positioned in the opening onthe longitudinal member.

♦ The bypass screw on the hydraulic pump must be opened after the repair position has been reached onvehicle from May 2007. This prevents damaging the hydraulic system.

– Open roof with convertible top operating switch until it is justbefore the position shown.

– Place Hinge Supports -VAS 6365- in lowest position -2-.

– Place the hinge supports -VAS 6365- in the mounting hole inthe main hinge -1- and rotate the base -4- so that it is not posi‐tioned in the opening in the longitudinal.

– Switch the ignition off. The roof lowers in stages until the sup‐ports are resting on the longitudinal member.

– Remove screws -3- and remove sunroof motor -2- from mount-4-.

Remove glass panel only with help from another colleague.

– First mark position of sliding blocks -7-.

– Only loosen screws -6- on sliding block -7-, do not remove.

– Move the roof pillar toward the outside -arrow a- until the slider-3- in the slotted guide rail -4- can be guided over to front guiderails -2- without touching -arrow b-.

– Pull the glass panel out approximately 25 cm.

– Loosen the cables -2- on the glass panel -1- from the left andright slotted guide rails -3-.

– Remove glass panel with slotted guide rail parallel out of rearguide rails -b arrows-. Raise front edge of glass panel slightly-arrow a-.

Installing

♦ Make sure all components such the slider and bracket are installed.♦ The sliders -6- in the slotted guide rail -8- are coated in rubber up to the slider -11-.♦ The washer -9- must fit exactly into the openings. The glass panel will make noises if the guiding edge is

damaged.♦ The lower brace -12- faces downward, as illustrated.

– Place the sliders -6 and 11- on the slotted rail -8-.

– Install the bracket and all the individual parts in this sequence:

♦ Screw -10- washer -9-, bracket -12-, washer -5-, glass panel-1-.

♦ Screw -10-, washer -9-, guide -8-, washer -5-, bracket -12-.

Install glass panel only with help from another colleague.

– Guide glass panel guide rails into rear guide rails.

Glass panel must be guided horizontally -a arrows- and parallelwhen doing this.

– Move roof pillar far enough toward outside -b arrows- so thatguide rail slider does not touch the front guide rails.

– Further installation is performed in the reverse order of re‐moval.

2.1.2 Glass Panel CablesRemoving

♦ All screws are microencapsulated and must always be replaced.♦ Screw tightening torque: 3 Nm.

– Loosen the end eyes -3 and 6- on tensioning bands-2 and 5- on the outside of the main hinge.

– Remove tensioned headliner without loosening additional ten‐sioning bands. Refer to⇒ “2.6.6 Tensioned Headliner, Removing”, page 248

♦ To support roof, both sides of luggage compartment trim should be either removed or installed.♦ The bypass screw on the hydraulic pump must be opened after the repair position has been reached on

vehicle from May 2007. This prevents damaging the hydraulic system.

– Place Hinge Supports -VAS 6365- in lowest position -2-.

– Remove the bolts -1-.

– Remove cover -2- from mount -4- and remove intermediateshaft -3-.

– First mark position of sliding blocks -7-.

– Only loosen screws -6- on sliding block -7-, do not remove.

– Move the roof pillar toward the outside -arrows a- until theslider in the slotted guide rail -4- can be guided over to frontguide rails -2- without touching.

– Pull the glass panel out approximately 25 cm.

– Loosen the glass panel cables -2- from the slotted guide rails-3-.

– Remove cables from rear guide rails.

Installing

– Guide glass panel cables -2- into rear guide rails.

– Insert glass panel cables -2- in guide rail mount -3-.

The -arrow- points to the direction of travel.

– Place sunroof motor -2- in mount on guide tube -4-.

– Install 3 bolts 3-3-, tightening specification 4.5 Nm.

– Crank glass panel back as far as “stop” using emergency op‐eration.

– Position sliding blocks on applied markings and tightenscrews. Tightening specification: 9.5 Nm.

– Close the CSC roof and remove the hinge supports -VAS6365- .

– Install the intermediate shaft and the sunroof motor.

– Install the tensioned headliner and loosened tensioning cable.

– Adapt sunroof motor.

2.1.3 Sunroof MotorRemoving

The glass panel remains closed.

– Remove tensioned headliner without loosening tensioningbands. Refer to⇒ “2.6.6 Tensioned Headliner, Removing”, page 248 .

Installing

♦ The sunroof motor is equipped with a closing force limit. If the roof runs into an obstacle during the closingprocedure, the motor stops and the glass panel moves in the opposite direction.

♦ If the glass panel is closed a second time with the switch, it runs with increased closing force. If the glasspanel still runs into an obstacle, it runs once again in the opposite direction.

♦ If the glass panel is closed a third time using the switch, it runs without a closing force limit.♦ All screws are microencapsulated and must always be replaced.

– Place sunroof motor -2- on mount -4- and tighten screws -3-.Tightening specification: 4.5 Nm.

Both a re-installed sunroof motor and a new sunroof motor mustalways be adapted.

♦ Pull switch, glass panel -1- closes.

♦ Pull switch a second time, glass panel closes with increasedclosing force.

♦ Pull switch a third time, glass panel closes without closingforce limit.

In this way, the sunroof motor is adapted and learns the zero po‐sition.

– Install tensioned headliner rail. Refer to⇒ “2.6.14 Tensioned Headliner Rail, Installing”, page 262 .

– Install the tensioned headliner. Refer to⇒ “2.6.7 Tensioned Headliner, Installing”, page 251 .

2.1.4 Glass Panel Seal, from July 2007

This seal is installed only on vehicle through July 2007.

Removing

– Open glass panel -1- completely.

– Remove seal -3- from mount in guide rails -2-.

Installing

– For easier installation, coat seal with soapy water.

– Carefully press seal -3- into guide rail mount -2-.

2.1.5 Guide RailsRemoving

After removing roof pillar trim, ensure trim is not damaged by the following roof movement.

– Loosen the end eyes -3 and 6- on tensioning bands-2 and 4- on the outside of the main hinge. Refer to⇒ “2.6.12 Routing Tensioning Bands 4 and 5”, page 260 . (asshown in illustration N61-10146)

– Remove roof pillar trim without loosening tensioning bands.Refer to ⇒ “2.6.15 Roof Pillar Trim”, page 263 .

– Remove screws -4- on eyes -3- and allow roof pillar trim -1- tohang down on tensioning bands -2-.

– Open glass panel completely.

– Insert Guide Rail Assembly Gauge -VAS 6370- in upper guidein guide rail -4-, slit on knurled screw -3- must be horizontal.

– Obtain dimensions Guide Rail Assembly Gauge -VAS 6370-on front -a- and rear -b- of front guide rails and note thesedimensions.

– To measure, slide the gauge open as far as the front -arrow-and rear stops -arrow-.

– Remove the gauges again.

– Place base -2- of Side Member Support -VAS 6367- on seatbelt guide rail -1- -arrow a-.

– Press the support together and allow the rectangular formationon the head -3- on the head to position itself on the guide rearguide rail -4- through the force of the spring-arrow b-.

– Tighten screws -5-.

– Measure the dimension between the head -3- and the screw-5- and note it down.

– Remove the support again.

– Place hinge supports -VAS 6365- in lowest position -2-.

– Switch ignition off, roof lowers in stages until supports -4- areresting on longitudinal member -5-.

– Remove inner seal -2- in area of front guide rails.

– Remove water guide foil -1-.

– Press seal on again.

– Mark the position of the screws -6-.

– Remove the screws -3, 4, 5 and 6-.

– Remove water drain from front guide rails. The water drainmay be bonded to the guide rail.

– Remove the guide rails -3- forward at an angle.

Installing

All screws are microencapsulated and must always be replaced.

– Install the guide rail -1- onto the guide -arrow a-.

– Turn the guide rail until the clip audibly latches into the roofpillar -arrow b-.

– Align the guide rail inside the roof pillar.

– Install the screws -3, 4, 5 and 6-.

Watch how the front and rear guide rails move when closing the convertible top.

– Close the roof as far as the windshield frame but do not lockit.

– Place base -2- of Side Member Support -VAS 6367- on seatbelt guide rail -1- -arrow a-.

– Press the support together and allow the rectangular formationon the head -3- on the head to position itself on the guide rearguide rail -4- through the force of the spring-arrow b-.

– Adjust the noted dimension.

– Tighten screws -5-.

– Check rear dimension -b- of guide rails -4- with Guide Rail As‐sembly Gauge -VAS 6370- .

– Adjust guide rails according to front dimension -a- that wasnoted using Guide Rail Assembly Gauge -VAS 6370- . Tightenthe screw -5-.

– Secure the gauge guide -1- in the guide rails -4-. Rotateknurled screw -3- so slit is vertical. Tighten knurled screw -2-.

All screws are microencapsulated and must always be replaced.

– Tighten the bolts -3, 4, 5 and 6-. Tightening specification: 9.5Nm.

– Place hinge supports -VAS 6365- in lowest position -2-.

– Remove the seal -2- in the glass panel area.

The guide rail must be free of dirt and grease.

– Install the water guide foil -1-.

The water guide foil must seal all around edges of front guide rail-arrows-.

– Press a Butyl Cord -D 450 273 A2- -3- formed into a ball onend of guide rail firmly onto water guide foil -1-.

– Press a second Butyl Cord -D 450 273 A2- formed into a ballfirmly onto water guide foil at a distance of 85 mm-dimension a- to first.

– Check for correct seating of both butyl cords on water guidefoil. No gap should be visible between both materials. Butylcord should not be formed to edge of guide rail.

– Secure seal -2- on roof pillar.

– Remove supports and close roof.

– Install roof pillar trim.

2.1.1 Glass Panel...5/8/2018 Glass Panel and Attachments → Removal and Installation → Body...

Documents

111 Stained Glass Panel and Suncatcher Patterns

for Bathrooms and Spas - Stained Glass Inc.Stained Glass Shower Doors Partitions Ceiling Tiles Windows Stained Glass Panel # 2934: Wisteria Vines Stained Glass Panel # 3041: Musical

S-DYN6235 DYN6445 DYN9235 Dynamic Manual Retyped€¦ · 3) Tempered Glass Door 4) Glass Window Panel 5) Bench Panel 6) Bench Emitter Panel 7) Back Protection Grid (Ceramic Model

TUB DOOR AND TUB DOOR GLASS PANEL INSTALLATION …pdf.lowes.com/installationguides/849388010153_install.pdf · Tub Door Glass Panel Installation Instructions ... Place the Glass door

Andersen Art Glass Installation Guide...Art Glass Panel Installation Casement Windows Proceed to below section and determine if the casement win-dow the Art Glass Panel is being installed

sliding Doors & Storage Solutions - Bedrooms Plus · New to 2017/18 Mild Walnut panel Cashmere panel Light Grey glass Lava panel Stone Grey panel Duck Egg Blue glass Spacepro sliding

Glass Panel Engine Monitor - Aircraft Spruce

KAHTP20BLKA 2000W Black Glass Portable Electric Panel

Google glass panel GDG Albuquerque Dev Fest, November 2013

Design Element: G2 - Semi-framed steel and glass panel balustrade

MotoLOGIC User Guide 0913

Mini Split Hi-Wall Inverter Glass Panel

2016 Chevrolet Cruze (Gen II - VIN B) · 3/7/2019 Headlining Trim Panel Replacement • 2016 Chevrolet Cruze (Gen II - VIN B) • MotoLogic

Glasstec...GW/GG Models GG-1628B Panel, Door, Notched Buttress Panel GCGGV Clamp Glass to Glass Vent and Wall Channels, Polished Chrome, 1/2” Clear Glass 6” C-Pull Handle GW-70

Klein Estates: Features and Finishes · 2020-03-01 · Free Standing Tub O.T.B. Niche or Opt. Coffee Bar Glass Door W/ Glass Panel (Frameless) Glass Door W/ Glass Panel (Frameless)

SHOWER ENCLOSURE INSTALLATION INSTRUCTIONS · Shower Enclosure Installation 1. Assemble the Wall brackets (14) onto the Stationary panel glass (01) and the Return panel glass (03)

No Job Name - Kohler Co. Door Panel Fixed Hinge Bottom Left/ Top Right Fixed Hinge Top Left/ Bottom Right Glass To Glass Seal Strike Lite Glass Panel Wall Jamb Wall Bracket Top Right

Leap Bi-Fold Door - Kohler Co. · 1000 Bi-fold Door 1 1781.389 Handle Glass Spare 1000 2 1781.392 Panel Glass Spare 1000 3 1781.398 Inline Panel Glass Spare 1000 4 1781.548 Handle

07SIB 16 4 GENOV KORR - Sika Slovenija stone facade Panel reinforcing, panel lamination Glass wall grouting, glass-to-glass applications Ventilated Facade ... The fasteners are adjusted

Acoustics Ceiling tiles|Acoustic Flooring Tiles ... · Perforated Gypsum Panel Perforated Gypsum & Glass fibre Composite Panel ... Glass Fiber Reinforced Gypsum Architectural products