Embed Size (px)
DESCRIPTION
www.gcequipment.com Skype:stan_globecore Transformer oil purification plant Globecore CMM4/7 designed for tratment of tranfromer oil and provides: • Removal of Water from 100 ppm down to 10 ppm and from 50 ppm to 5 ppm in a single pass and down to 3 ppm after 3 passes (ASTM method D-1533). • Reduction of Gas content from fully saturated with air (10 to 12% by volume) to less than 0.1 % (ASTM D-2945). • Removal of Particulate Matter to 5 microns • Improvement in dielectric strength up to 75 kV
Citation preview
www.gcequipment.com
GlobeCore High Vacuum Degasifier CMM(UVM) 4
Technical and Price Offer
GlobeCore Mobile High Vacuum Degasifier CMM (UVM) 4
GlobeCore Europe 8 Sadovskogo Street Poltava 36034, Ukraine Tel: +380532 241211 Fax: +380532241211 Mob: +380500131317 Email: [email protected]
CMM (UVM) 4 - is supplied: mounted on a roadworthy trailer with torsion suspension, appropriate reflectors and tail lights and capable of being towed at speeds of up to 80km/h. It will be enclosed with water proof metal covers (protection class IP45) and have a mechanism to secure plant in stationary position while in operation.
Maximum noise level emitted by the unit will be below 80 db. Production capacity of the unit is 4000 L/H allowing to process up to 96000 L of transformer oil per day and provide:
• Removal of Water from 100 ppm down to 10 ppm and from 50 ppm to 5 ppm in a single pass and down to 3 ppm after 3 passes (ASTM method D-1533). • Reduction of Gas content from fully saturated with air (10 to 12% by volume) to less than 0.1 % (ASTM D-2945). • Removal of Particulate Matter to 5 microns • Improvement in dielectric strength up to 75 kV
COMPONENTS DESCRIPTION:
I. VACUUM SYSTEM
CMM (UVM) 4 has the following vacuum facilities:
1. “GlobeCore” Rotary Vane Positive Displacement Pump Pumping Speed 100 m3/h Ultimate Pressure 0.5 mbar
2. “Globe Corel” Vacuum Booster Pumping Speed 270 m3/h Ultimate Pressure 0.01 mbar
II. VACUUM CHAMBER
This Oil Purification plant has horizontal Vacuum Column with Coalescers. Vacuum Chamber Vessels and all internal parts are made of carbon steel and feature Coalescers, Sight Glass, Oil Level Controller and Vacuum Gauge. Vacuum Chamber’s rigid design makes it suitable for stationary and mobile installation. Appropriate flexible connections are provided to the outlet pump and inlet pump to minimize negative effect of vibration during plant operation and transportation.
Vacuum Chamber
1–Oil Inlet 2–Vacuum Pump Connection 3–Coalescers 4–Oil Outlet 5–Level Sensor 6–Sight Glass
Coalescers - four built-in coalescers are provided for the maximum exposure of oil to the effect of vacuum. Due to reduced pressure dissolved water and gases are vaporised through secondary chamber and filter into atmosphere. Secondary Chamber (Oil Trap) - serves as safety feature to ensure that no oil is pulled into the vacuum pump. It is equipped with oil level sensor which will activate the alarm in case of oil presence. Oil Level Controller - consists of three capacitive probes provided to maintain required level of oil in the Vacuum Chamber. Vacuum Gauge - is provided to monitor Vacuum level in the Vacuum Chamber. Vacuum gauge will be absolute type with display in mbar. Vacuum ports – vacuum connection is provided to pull vacuum on transformer. Sampling Ports – inlet and outlet oil ports are provided for incoming and processed oil.
III. OIL HEATER
The electric oil heating facility is provided in 2 stages offering a total of 55 kW of power. A low watt density encapsulated heating elements (1.2 W/cm²) are used to prevent heat degradation of oil. The Heater is controlled by electronic temperature controller.
IV. INLET AND OUTLET OIL PUMPS
Inlet Oil Pump : “Calpeda” Centrifugal Pump with power consumption of 1.5 kW and maximum capacity of 7 m³/h.
Outlet Oil Pump: “Calpeda” Centrifugal Pump with power consumption of 2.2 kW and maximum capacity of 7 m³/h.
V. FILTERS
A 90 micron Mesh Strainer is provided to remove large particles that could cause damage to the Inlet Pump. 25 micron Coarse Filter is installed on entry to the Vacuum Chamber. Oil receives its final treatment by passing through the 5 micron Fine Filter designed to remove 99.9% of particles larger than 5 microns.
Oil Heater 1–Vessel 2–Heater’s cover 3–Heating Elements 4–Oil Outlet 5–Oil Inlet 6–Drainage and Safety Valve 7–Thermal Converters
Coarse and fine Filters
1–Oil Inlet 2–Oil Outlet; 3–Drain Valve 4–Air Valve 5–Manual Air Discharge 6–Magnets 7–Clamp 8–Filter Cartridge
VI. ALARMS AND INTERLOCKS
GlobeCore’s CMM plants feature the following safety devises which ensure simple and reliable operation and will safely shut down the system in case of any alarm situation: High Level Alarm - will alert plant’s operator by activating sound and light alarms and shut down the system safely should high level of oil persist. Low Level Alarm – interlocked with the inlet pump low level alarm will safely shut down the plant in case of insufficient oil level. Flow Sensor - only activates the Heater when oil flow is detected. Overloads – all motors are protected by overloads. Alarms – sound and light alarm with silence button will alert plant’s operator of any emergency situations.
VII. INSTRUMENTATION AND CONTROLS
Control panel is a dust proof enclosure (protection class IP 54) featuring the following elements:
Vacuum meters - monitor vacuum level in the vacuum chamber and secondary chamber. Manometers - are installed to monitor the state of Coarse and Fine Filters and oil pressure on outlet. Temperature controller – takes an input from temperature sensor and connected to a control element of the heater. Measuring and control parameters are pre-set by the manufacturer. Power and Heating Indicators and Switches, Inlet and Outlet Oil Pumps Switches, Vacuum Pump and Vacuum Booster switches Emergency Stop Button – is provided for safe shut down of the plant in case of emergency.
VIII. FLOW DIAGRAM
Typical Flow Diagram CMM (UVM) 4 СV – Vacuum Chamber; P1 – P2 – Oil Pumps; K1 – K12 – Ball Valves; K2 – Vacuum Valve, MN – Oil Heater; ВV– Back Valve; F1, F2 – Fine Filter; М1, М2, М3– Manometers; ТP – Temperature Sensor; ТS – Thermostat; RF – Flow relay; EV1- EV6 – Electromagnetic Valves; VG1 , VG2 – Vacuum Relay; L1 – L4– Level Sensors; VP1, VP2 – Vacuum Pumps; РF – Mesh Filter; R – Oil Trap, RP– Pressure Relay.
OPERATIONAL PRINCIPLE
The unit can be operated in the following modes:
- oil heating and filtration
- filtration, heating and thermo-vacuum oil purification
- vacuummising of a transformer tank
Heating and filtration mode: oil goes through the unit via valve K1, mesh filter РF, valve K10 pumped by oil pump P1 through the oil heater MN, cartridge filter F1, ball valve K2, K5 to the unit output.
Filtration, heating and thermo-vacuum oil purificat ion: transformer oil is fed through valve K1, mesh filter РF, valve K10, oil pump P1 through oil heater MN, cartridge filter F1. Heated to temperature (50…60ºС) and purified from mechanical impurities oil is fed through ball valve K3, comes into vacuum column CV, passes through coalescers. Vacuum in the chamber is created by vacuum pump VP. Vacuum value in the chamber is maintained by means of the valve К11 and controlled by vacuum gage VM. Air is supplied into chamber through moisture eliminator FV, ascending air carries out gases and water vapour from the oil surface and in this way the oil is dried. Wet air is subsequently removed into atmosphere via vacuum pump. Oil from the column is fed to the transformer by oil pump P2 through valves K8, K9, cartridge filter F2, return valve SV and ball valve K5 into the tank for clean oil. The K3 valve establishes necessary flow rate. The vacuum in the column is created by vacuum pump VP1 and maintained at 0,8 bar during operation. Vacuumizing of transformer: is carried out by pump VP through valve for vacuumizing of the external equipment.
SPECIFICATIONSName of parameter Value
1 Productivity, m3/h, minimum
- in thermo-vacuum dehydration and filtration mode 4 - in heating and filtration mode 7
2* Processed oil parameters :
- maximum gas content, %, max. 0.1
- maximum moisture content, ppm, after 3 passes 5
3 Maximum oil outlet temperature in heating mode , ºС 70
4 Outlet pressure, MPa 0,2
5 Oil heater power, kWt, max. 55
6 Maximum power consumption, kWt, max. 65
7 Electric current parameters,
- voltage, V 400/220 - AC frequency, Hz 60
8 Dimensions СММ(UVM) 4, mm,
- length 1650
- width 1250
- height 1590
9 Weight, kg 990
3D DIAGRAM and PICTURES
1 – Vacuum Chamber; 2 – Inlet Oil Pump ; 3 – Outlet Oil Pump; 4 – Pipes and Connections; 5 – Oil Heater; 6 – Fine Filter; 7 – Vacuum Pump; 8 – Vacuum Booster
GlobeCore High Vacuum Degasifier CMM (UVM) 4
GlobeCore Mobile High Vacuum Degasifier CMM (UVM) 4
Vacuum Column Vacuum Pumps
Warranty: GlobeCore warrants the machinery supplied under this specification against defects in material and workmanship under normal use and service for a period of 12 months from date of shipment.
Yours sincerely, Stanislav Sukhar Sales Manager Globe Core Ltd Tel/Fax: +380532241211 Mob: +380500131317 Email: [email protected]
