Upload
durga-prasad
View
1.149
Download
1
Embed Size (px)
Citation preview
Directions for Numbers s 1- 73 :Read each of the following multiple-choice
items and the possible answers carefully. Mark the letter of the correct answer on
your answer sheet or as instructed by your teacher. REMEMBER: MAKE NO
MARKS ON THIS TEST.
1What is the correct FRONT view in the figure
below?
2What is the correct FRONT view in the figure
below?
3If a cylinder is cut as illustrated below, the
RIGHT SIDE view will contain a/an:
A Circle.
B Ellipse.
C Rectangle.
D Triangle.
4Which is the correct TOP view in the figure
below?
Page 1 of 15
Go on to next page
5Which statement is MOST accurate concerning
missing lines in the views?
A Lines are missing in the top view.
B Lines are missing in the front view.
C Lines are missing in the front and right side
views.
D All three views are complete (no lines
missing).
6What is the correct FRONT view in the figure
below?
7Which is the correct RIGHT SIDE view of the
figure below?
8Dimension “A” in the TOP VIEW is the:
A Altitude.
B Side to side.
C Bottom to top.
D Front to back.
Page 2 of 15
Go on to next page
9According to its position, view X in the
illustration below is the:
A Front.
B Left side.
C Right side.
D Top.
10In the figure below, the edge view of surface
“A” will appear TRUE LENGTH in the:
A Bottom view.
B Front view.
C Right side view.
D Top view.
11Hidden edges are indicated by:
A Alternate, long and then short, dash lines.
B Thick, dark, solid lines.
C Two short dashes followed by one long
dash.
D Uniform "81 long dashes.
12In the figure below, the edge view of surface
“A” will appear TRUE LENGTH in the:
A Top view.
B Right side view.
C Front view.
D All views.
13What is the correct RIGHT SIDE view of the
figure below?
14In orthographic projection, lines are formed by
projecting edges of the object onto planes. The
images formed on the planes are called:
A Views.
B Sides.
C Points.
D Tangencies.
Page 3 of 15
Go on to next page
15What is the correct TOP view in the figure
below?
16What is the correct TOP view of the figure
below?
17The term ORTHOGRAPHIC PROJECTION
means to:
A “Throw backward at an angle of 45° and
draw.”
B “Throw forward at an angle of 45° and
draw.”
C “Throw forward at right angles and draw.”
D “Rotate the object at 45° to the picture
plane.”
18What is the MINIMUM number of views
necessary to describe the three dimensions of
the object below?
A One view
B Two views
C Three views
D Four views
19What is the correct FRONT view of the figure
below?
20Which of the following is the BEST example of
drawing CENTER lines?
Page 4 of 15
Go on to next page
21In the figure below, surface “A” will appear
TRUE SIZE and TRUE SHAPE in:
A All of the customary views.
B None of the customary views.
C The front view only.
D The top view only.
22What is the correct RIGHT SIDE view in the
figure below?
23What is INCORRECT about describing an
object?
A Some objects can be described with only
two views.
B Some objects can be described with only
one view.
C The most descriptive view is typically the
top view.
D Use only the number of views necessary to
describe the object.
24What type of line must be drawn between points
A & B to complete the LEFT SIDE view of the
figure below?
A Center
B Hidden
C Section
D Visible
25What is the correct TOP view in the figure
below?
26Which is the correct FRONT view of the figure
below?
Page 5 of 15
Go on to next page
27Where is the HIDDEN LINE drawn
INCORRECTLY in the figure below?
28What is the correct RIGHT SIDE view in the
figure below?
29The object shown below is composed of:
A Normal surfaces only.
B Normal and inclined surfaces.
C Inclined and oblique surfaces.
D Normal and oblique surfaces.
30Which is the correct TOP view of the figure
below?
31What is the correct TOP view in the figure
below?
32ORTHOGRAPHIC PROJECTION is a
system that allows you to make:
A Three-dimensional drawings of a two-
dimensional object.
B Two-dimensional drawings of a two-
dimensional object.
C Two-dimensional drawings of a three-
dimensional object.
D Three-dimensional drawings of a three-
dimensional object.
Page 6 of 15
Go on to next page
33The PRECEDENCE OF LINES tells us that if
a visible line and a hidden line coincide (occupy
the same position on the drawing), we should:
A Draw only the hidden line.
B Draw only the visible line.
C Draw the hidden line just above the visible
line.
D Replace them with a phantom line.
34The PRECEDENCE OF LINES tells us that if
a visible line and a center line coincide (occupy
the same position on the drawing), we should:
A Draw only the center line.
B Draw only the visible line.
C Draw the center line just above the visible
line.
D Replace them with a phantom line.
35When a surface ALWAYS appears as a
FORESHORTENED SURFACE (never as a
line) on the six regular planes of projection it is
classified as:
A Inclined.
B Normal.
C Sloping.
D Oblique.
36According to the correct arrangement of views,
the BACK VIEW would be placed adjacent to
the:
A Top view.
B Left side view.
C Right side view.
D Bottom view.
37A fast and accurate method of constructing the
side view once the top and front views are
established is by using a:
A Hidden line.
B Miter line.
C Width line.
D Metered line.
38IN MOST CASES, you can completely
describe the shape and size of an object by
drawing:
A One view.
B Two views.
C Four views.
D Two or three views.
39When making a multiview drawing of an object,
you need to draw:
A Only as many views as are needed to
describe the shape.
B Three views.
C Two views.
D Six views.
40When making a three-view drawing, all of the
following methods can be used to transfer depth
measurements EXCEPT:
A A miter line.
B Dividers.
C A scale.
D Straight line projection.
Page 7 of 15
Go on to next page
41When a CURVED SURFACE is TANGENT
to a PLANE SURFACE:
A No line should be shown where they join.
B An edge is formed where they join.
C A curved line is produced.
D The curved surface will appear as a hidden
line.
42OBJECT/VISIBLE lines are indicated by:
A Alternate, long ( "43 to 1 "
21 ) and then short
( "161 to "
321 ) dashed lines.
B Thick, solid lines.
C Thin, solid lines.
D Uniform "81 dashes.
43Which is a CENTER LINE?
44In a FRONT VIEW, the distance across an
object, from one side to other side, is the:
A Altitude.
B Width.
C Height.
D Depth.
45A MITER LINE is drawn at an angle of:
A 30º.
B 45º.
C 60º.
D 90º.
46The face of the object that has the most
descriptive feature(s) should be the:
A Back.
B Front.
C Right side.
D Top.
47The most often used combination of views
includes the:
A Top, front, and right side.
B Top, front, and left side.
C Top, front, right side, left side, and back.
D Top and right side.
48The number of ORTHOGRAPHIC views
provided by the planes of a box is:
A 1.
B 3.
C 6.
D 9.
49When making an orthographic drawing, the
THICKEST lines should be the:
A Center lines.
B Visible (object) lines.
C Extension lines.
D Hidden lines.
50The FRONT TO BACK dimension of an
object is known as the:
A Altitude.
B Depth.
C Height.
D Width.
Page 8 of 15
Go on to next page
51Surfaces and edges that CANNOT be seen from
the outside of the object are identified by:
A Hidden lines.
B Invisible lines.
C Opaque lines.
D Unseen lines.
52Another term for ORTHOGRAPHIC
DRAWING is:
A Isometric drawing.
B Oblique drawing.
C Multiview drawing.
D Perspective.
53Drawings of objects with very little thickness
(like an erasing shield) require:
A One view.
B Two views.
C Three views.
D Four views.
54In the term “ORTHOGRAPHIC
PROJECTION,” the “GRAPHIC” refers to:
A To throw.
B Forward.
C Written or drawn.
D At right angles.
55On a technical drawing, a plane is an imaginary
flat surface that has:
A No thickness.
B Height and width.
C Depth and height.
D Very little thickness.
56Surfaces or edges that CANNOT be seen in the
views are drawn with:
A Centerlines.
B Visible/Object lines.
C Hidden lines.
D No lines.
57Orthographic projection involves the use of
three planes. They are:
A Vertical (frontal), profile, and level.
B Horizontal, vertical (frontal), and profile.
C Horizontal, profile, and level.
D Straight, level, and inclined.
58The distance from the BOTTOM of an object to
the TOP of the object is:
A Circumference.
B Width.
C Height.
D Depth.
59How many views should be drawn if the object's
thickness is given in a note?
A One
B Two
C Three
D Six
60In an orthographic drawing, a circular surface
may NOT appear as a/an:
A Ellipse.
B Circle.
C Straight line.
D Parabola.
Page 9 of 15
Go on to next page
61A line at an angle of less than 90° to a plane of
projection will appear as a:
A Point.
B True length line.
C Curved line.
D Foreshortened line.
62When a surface slants away from a plane of
projection, it appears as a:
A Foreshortened surface.
B Foreshortened line.
C Normal surface.
D True-shaped surface.
63What three dimensions do all objects have?
A Height, width, and radius
B Angle, height, and depth
C Height, width, and depth
D Angle, depth, and radius
64The LEFT SIDE view consists of:
A Depth and height.
B Width and depth.
C Height and circumference.
D Width and height.
65The REAR view consists of:
A Height and depth.
B Width and height.
C Height and length.
D Width and length.
66The FRONT view consists of:
A Depth and height.
B Width and depth.
C Height and circumference.
D Width and height.
67The RIGHT SIDE view consists of:
A Depth and height.
B Width and depth.
C Height and circumference.
D Width and height.
68The TOP view consists of:
A Depth and height.
B Width and depth.
C Height and circumference.
D Width and height.
69The RIGHT SIDE view is taken from the:
A Horizontal plane.
B Frontal plane.
C Vertical plane.
D Profile plane.
70CENTER lines should be:
A Thick.
B Medium thick.
C Thin.
D Very thin, very light.
Page 10 of 15
Go on to next page
71HIDDEN lines should be:
A Thick.
B Medium thick.
C Thin.
D Very thin, light lines.
72The TOP VIEW is normally placed above the:
A Right side.
B Front.
C Left side.
D Back.
73When two surfaces intersect they form a:
A Line.
B Point.
C Solid.
D Surface.
74When a surface ALWAYS appears as a
FORESHORTENED SURFACE (never as a
line) on the six, regular planes of projection it is
classified as what type of surface?
A Inclined
B Normal
C Sloping
D Oblique
75The slot in Figure D1005.02.02 above is hidden
in the:
A Front view.
B Top view.
C Left side view.
D Bottom view.
Page 11 of 15
Go on to next page
Directions for Numbers s 76- 98 :Read each of the following multiple-choice
items and the possible answers carefully. Mark the letter of the correct answer on
your answer sheet or as instructed by your teacher. REMEMBER: MAKE NO
MARKS ON THIS TEST.
Figure D1005.02.04
76How will surface ADEG in Figure
D1005.02.04 above appear in the RIGHT SIDE
view?
A True size and shape
B As an edge
C Foreshortened
D Skewed
77What type of surface is ABCG in Figure
D1005.02.04 above?
A Frontal
B Horizontal
C Inclined
D Profile
78What type of surface is ADEG in Figure
D1005.02.04 above?
A Frontal
B Horizontal
C Inclined
D Profile
79What type of surface is EFG in Figure
D1005.02.04 above?
A Frontal
B Horizontal
C Inclined
D Profile
80What type of surface is GHJ in Figure
D1005.02.04 above?
A Frontal
B Horizontal
C Inclined
D Profile
81What type of surface is CJL in Figure
D1005.02.04 above?
A Frontal
B Horizontal
C Inclined
D Profile
82What type of surface is FHLK in Figure
D1005.02.04 above?
A Frontal
B Horizontal
C Inclined
D Profile
Page 12 of 15
Go on to next page
83What type of surface is HJL in Figure
D1005.02.04 above?
A Frontal
B Horizontal
C Inclined
D Profile
84What type of surface is CJG in Figure
D1005.02.04 above?
A Frontal
B Horizontal
C Inclined
D Oblique
85How will surface ADEG in Figure
D1005.02.04 above appear in the TOP view?
A True size and shape
B As an edge
C Foreshortened
D Skewed
86How will surface HJL in Figure D1005.02.04
above appear in the BACK view?
A True size and shape
B As an edge
C Foreshortened
D Skewed
87How will surface HJL in Figure D1005.02.04
above appear in the RIGHT SIDE view?
A True size and shape
B As an edge
C Foreshortened
D Skewed
Figure D1005.02.02
88The hole in Figure D1005.02.02 above is
visible in the:
A Bottom view.
B Front view.
C Left side view.
D Right side view.
89The slot in Figure D1005.02.02 above is visible
in the:
A Bottom view.
B Rear view.
C Left side view.
D Right side view.
90The hole in Figure D1005.02.02 above is
hidden in the:
A Front view.
B Left side view.
C Rear view.
D Pictorial view.
Page 13 of 15
Go on to next page
Figure D1005.01.01
91Line AB in the figure above is a/an:
A Square line.
B Miter line.
C Isometric line.
D Perpendicular line.
92Line CD in the figure above is a/an:
A Isometric line.
B Center line.
C Hidden line.
D Visible line.
93Line E in the figure above is a/an:
A Center line.
B Visible line.
C Square line.
D Hidden line.
94Line F in the figure above is a/an:
A Visible (Object) line.
B Square line.
C Center line.
D Hidden line.
Figure D1005.02.01
95Which line in the figure above is parallel to the
DEPTH of the object?
A AB
B CD
C EF
D AF
96Which line is parallel to the HEIGHT of the
object shown above?
A AB
B CD
C EF
D AF
Page 14 of 15
Go on to next page
Figure D1005.02.03
97Which is the FRONTAL surface in Figure
D1005.02.03 above?
A 2
B 3
C 4
D 5
98Which is the PROFILE surface in Figure
D1005.02.03 above?
A 2
B 3
C 4
D 5
Page 15 of 15
Stop here