Katalog produk-aeroqual-air-quality-monitoring-tridinamika

© Aeroqual Ltd, 2011 Aeroqual Limited All rights reserved www.aeroqual.com March 2011

UV-1 UV Ozone Photometer OEM Module Description The Aeroqual UV-1 Ozone Photometer Module is designed for measurement and control of ozone in the range 0-200 ppm using a single beam UV photometer. It has a folded metal enclosure designed to be built into an ozone treatment system. The UV- 1 offers advanced monitoring and control.

Features • Wide measurement range (0-200 ppm) • Single-beam UV photometer • Pump sampling via PTFE tubing (e.g. monitoring outside of a room or duct) • Digital RS485 output (2 wire) or RS232 • Custom configuration upon request

Specifications Range 0-200 ppm Ozone Precision <±5% of reading above 0.2 ppm

±0.01 ppm below 0.2 ppm Resolution 0.01 ppm T90 <60s Sampling method Brushless DC diaphragm pump Sample flow rate 0.4 ±0.05 LPM Inlet filter 5 µm pore size, 37 mm PTFE filter Pneumatic connections Kynar 6.25mm (¼” ) compression fittings Wetted Materials Kynar, Teflon PFA, quartz, aluminium, viton Environmental operating conditions Temperature RH

0-40°C 0-95% RH (non-condensating)

Power requirements 24VDC, 2A Digital interface RS485 (2 wire), RS232 (Communication protocol supplied) Connectors Screw Enclosure Folded Aluminium

280 x 120 x 90 mm Software RS232 datalogging software supplied Options 0-5 V analog output, 12 bit

Accessories (optional) 24VDC DIN rail mount 100-250V AC (R35) Spare inlet filters (25 pack) (R12) RS485 to USB converter (R53) 10m x 6.25mm OD PFA tubing (R66)

Indicative picture of UV-1

© Aeroqual Ltd, 2009 Aeroqual Limited

All rights reserved www.aeroqual.com November 2009

Series 900 | 905 Gas Transmitter & Controller

Features • Active sampling for higher accuracy

• Multiple analog & digital outputs

• Real-time network capability

• Interchangeable sensor heads

• PC data logging & networking option

• Temperature & RH sensor (Series 905)

Applications • Ozone generator control applications

• Ambient & monitoring and control

• Real-time network monitoring

• Indoor air quality monitoring

• Health & safety

Specifications

Ozone Sensor Heads (other gases available)

Sensor Head

Calibrated Range

Maximum Exposure

Lowest Detection

Accuracy of Calibration

Resolution Response Time (T90)

Operating Conditions

OZU 0-0.15ppm 0.25ppm 0.001ppm <±0.005 ppm 0.001ppm < 70 s

OZL 0-0.5ppm 1ppm 0.001ppm <±0.008 ppm 0- 0.1ppm

<±10% 0.1-0.5 ppm 0.001ppm < 60 s

OZG 0-10ppm 15ppm 0.01ppm <±0.1 ppm 0-1 ppm <±15% 1-10 ppm

0.01ppm < 60 s

Temperature -5°C to 40°C

Humidity 5 to 95% RH (non-condensing)

Power (user supplied) Regulated 12V DC, 800mA

Analogue output 4-20mA (opto-isolated), 10-30V

External signal type Transistor outputs (4)

External signal functions Low Alarm, High Alarm, Control and Diagnostics

Inputs Standby toggle

Communication RS485 (Aeroqual proprietary protocol)

Jumpers J1, J2, J3 termination resistors

Connectors Screw

ID 1 (Default) - User configurable from 1 to 255

Alarm set points (2) User configurable

Control set point User configurable

Removable / replaceable / refurbish-able sensor head Yes

Sampling method Active sampling via internal sensor fan

Temperature & Humidity sensor (Series 905) Range -40°C to 124°C (-40°F to 255°F) | Range 0 to 100% RH

Configuration software (standard) PC Configuration Program CD (supplied)

Data logging & networking software (optional) PC Data Logging & Networking CD (code: R60)

USB interface (optional) RS485 to USB converter (code: R53)

Power supply (optional) 12V DC DIN rail mount 100-250V AC (code: R37)

Enclosure casing & rating Polycarbonate; IP20 & NEMA 1 equivalent

Enclosure size (with base unit) 64 x 130 Ø (mm); 2½ x 5⅛ Ø (in)

Mounting Screw fixture

Weight < 200 g; < 7 oz

Approvals Part 15 of FCC Rules EN 50082-1: 1997 EN 50081-1: 1992

© Aeroqual Ltd, 2013 Aeroqual Limited MRK-D-0003 V1

All rights reserved www.aeroqual.com

AQM60

Air Quality Monitoring Station

Accurate real-time air quality information,

made affordable.

For those needing to measure and manage common outdoor air pollutants, the AQM60 enables near-analyser levels of performance at a fraction of the cost of traditional reference monitoring stations.

The AQM60 is a totally configurable instrument platform able to measure common air pollutants including ozone (O3), nitrogen dioxide (NO2), nitrogen oxides (NOX), carbon monoxide (CO), sulphur dioxide (SO2), volatile organic compounds (VOC), hydrogen sulphide (H2S), non-methane hydrocarbons (NMHC), carbon dioxide (CO2), particulate matter (TSP, PM10, PM2.5, PM1), noise and meteorological parameters such as temperature, humidity, wind speed and direction.

Key Features

• Continuous measurement of common air pollutants

• Information available in real-time

• Compact and light enough to be carried by one person

• Quick and easy to install and relocate

• Flexible integration of meteorological and noise sensors

• On-board data-logging and remote data retrieval

• Gas modules allow for ease of maintenance

• Robust, temperature-controlled enclosure

• Automated calibration optional

• Calibrated against USEPA (40 CFR Part 53) and EU (2008/50/EC) certified equivalent method instruments

Applications

• Urban air quality monitoring

• Perimeter: petrochemical, power plants, waste sites, industrial point sources

• Airport, ports, railways, construction sites

• Short term monitoring of ‘hot spots’

• Community exposure: epidemiological studies, microenvironment, residential, schools, hospitals

• Near road: motorways, street canyons, traffic information systems

• Environmental impact assessments

Selected Customers

• Dubai Municipality, UAE

• Vale, Brazil

• URS Corporation, Australia

• Repsol YPF, Argentina

• Directorate General of Traffic, Spain

• Saudi Electricity Company, Saudi Arabia

• Cape Town City, South Africa

• Bengkalis Municipality, Indonesia

• Qingdao Government, China

© Aeroqual Ltd, 2013 Aeroqual Limited MRK-D-0003 V1


AQM60 Specifications

Typical configuration: 1 to 6 gas modules, particle monitor, weather sensor and auto-calibration system.

Gas Modules Range Minimum

Detection Limit Accuracy of

Factory Calibration Precision Resolution

Ozone O3 (GSS) 0-0.5 ppm 0.001 ppm <±0.008ppm 0 to 0.1 ppm;

<±10% of reading above 0.1 ppm 0.005 ppm 0.001 ppm

Nitrogen Dioxide NO2 (GSS) 0-0.2 ppm 0.001 ppm <±0.01 ppm 0 to 0.1 ppm;


Nitrogen Oxides NOx (GSS) 0-0.5 ppm 0.001 ppm <±0.01 ppm 0 to 0.1 ppm;


Carbon Monoxide CO (GSE) 0-25 ppm <0.04 ppm <±0.1ppm, 0 to 1 ppm

<±10% of reading above 1 ppm 0.1 ppm 0.01 ppm

Carbon Dioxide CO2 (NDIR) 0-2000 ppm <10 ppm <±(10 ppm + 5% of reading) 10 ppm 1 ppm

Hydrogen Sulphide H2S (GSE) 0-10 ppm <0.03 ppm <±0.05ppm 0 to 0.5 ppm

<±10% of reading above 0.5ppm 0.03 ppm 0.01 ppm

Sulphur Dioxide SO2 (GSE) 0-10 ppm <0.03 ppm <±0.05ppm 0 to 0.5 ppm


Volatile Organic Compounds (PID) 0-20 ppm 0.01 ppm <±0.02ppm 0 to 0.2 ppm


Non-methane Hydrocarbon (GSS) 0-25 ppm <0.1 ppm <±0.1ppm, 0 to 1 ppm

<±10% of reading above 1 ppm 0.1 ppm 0.01 ppm

Particle Monitor (nephelometer) Sizes

PM1 PM2.5 or PM10

Range

0-2000 µg/m3

Accuracy

<±(2 µg/m3 + 5% of reading)

Flow rate

2.0 LPM

Resolution

0.01 µg/m3

Particle Profiler (OPC) Sizes

PM1 PM2.5 and PM10

Range

0-500 µg/m3

Accuracy

<±(5 µg/m3 +

15% of reading)

Flow rate

1.0 LPM

Resolution

0.01 µg/m3

Control Module

Communication

RS 232

Data Storage

2 GB SD card

Data- logging Interval

2 to 255 minutes

Display

VFD 4 x 20

Status

Event Log

Gas Treatment Module

Sampling Pump

12V diaphragm

Inlet Manifold

PTFE/PVDF

Zero Scrubber Media

Purafil chemisorbant, activated carbon & hopcalite

Thermal Management System Setpoint controlled A/C system

Software PC software for configuration,

calibration and data acquisition

Manual Gas Calibration

(optional) AIRCAL 1000 portable calibrator with

gas dilution module and zero air source

Automatic Gas Calibration

(optional)

AIRCAL 8000 integrated calibration

system with gas dilution module, zero

air source and span gas storage

Wireless communication

(optional)

Cellular IP Gateway

RF Modem

GSM Modem

Third party sensors

(optional)

Gill WindSonic (ultrasonic wind sensor)

Vaisala WTX520 (weather transmitter)

ACO Pacific SA6000 (noise monitor)

Power Requirements 100-240V AC; 100-150W

(depends on configuration)

Enclosure IIP65 fibre reinforced polycarbonate with

aluminium solar shielding and

compressor housing

Dimensions (H x W x D) in mm 900 x 555 x 400

Height with PM10 inlet : 1300

Environmental Operating Range Temperature: -20°C to +50°C;

RH: 10 to 95%

Weight 25-40 Kg

Conformity

Power Supply : EN55015, EN55022 Class B, EN61000-3-2,3, EN61000-4-2,3,4,5,6,8,11,

ENV50204, EN61547, EN61347-1, EN61347-2-13; UL1012, UL60950-1; TUV EN60950-1

Gas Modules : Part 15 FCC Rules, 2004/108/EC; EN 61000-6-1: 2001, EN 61000-6-3: 2001 Particle Monitor & Profiler : Class 1 laser;

IEC 60825-1:1998; 72/23/EEC; EN 61010-1; EN 60825-1:1996; US 21 CFR 1040.10

© Aeroqual Ltd, 2013 Aeroqual Limited MRK-D-0015, V3


DUST SENTRY

Specifications

Measurement technology Near forward light scattering nephelometry

Range 0-2000µg/m3

Accuracy +/- (2 ug/m3 + 5% of reading)

Cut points available PM10, PM2.5, PM1, or TSP

Sample flowrate 2.0 LPM

Inlet 36cm heated inlet

Alarm Relay, Email and SMS (optional)

Display 4-line alpha-numeric

Datalogging 2GB SD card (>15 years data storage)

Averaging period 1-60 minutes

Reference filter 47mm GFA circular filter (optional)

Software Datalogging and configuration software included

Outputs RS232, 4-20mA / 2-10V (optional)

Mounting Pole, tripod and wall mounting

Wireless communication options GSM/GPRS modem with GPS; Orbit DATA (cloud-based DAS)

Integrated sensor options Wind speed and direction; temp/RH; rain; pressure; noise (Class 1)

Environmental operating range -10°C to +45°C; 10 to 95% RH (NC)

Power requirements Power requirements Mains 100 - 260V, 18W (standard) or regulated

12 (+/- 2.5%) VDC with <150 mVp-p ripple and noise (15W)

Enclosure IP65-rated Lockable GRP Cabinet: Width 330mm x Depth 187mm x

Height 483mm (including solar shield armour & mounting brackets)

Weight <12kg

Conformity

(MCERTS pending)

OUTDOOR REAL-TIME PARTICULATE MONITORING

Designed for those who need to monitor and manage dust emissions as and when they happen, the Dust Sentry is a nephelometer-based instrument that delivers affordable and accurate real-time measurement of PM10, PM2.5, PM1, or TSP. Compared to reference-equivalent monitors like TEOMs and BAMs which lack sensitivity at short sampling periods, the Dust Sentry reports accurately at 1 minute intervals and has a lower total cost of ownership (up to 5x less). In addition, the Dust Sentry is compact, re-locatable and can integrate wind, noise and weather sensors for maximum utility.

Highlights

• Measures and reports data in 1 minute intervals

• Accurate measurement of PM10, PM2.5, PM1, or TSP.

• On board data storage for up to 15 years of data

• Email and GSM data retrieval and alerts

• Tough weatherproof enclosure with solar shielding for hot climates

• Option to integrate weather, wind, noise and sirens

Applications

• Construction site monitoring

• Roadside and tunnel monitoring

• Mine and quarry perimeter monitoring

• Waste transfer and treatment site monitoring

© Aeroqual Ltd, 2012 Aeroqual Limited IAQ Survey Kit April 2013


IAQ Survey Kit Portable Indoor Air Quality Monitoring

For indoor air quality consultants, building inspectors and health & safety managers who need to measure indoor air quality on the move, the Series 500 IAQ enables simultaneous measurement of up to 5 different parameters: CO, CO2, VOC, temperature and relative humidity. Plus, by adding any one of our many interchangeable sensor heads, the monitor can be further expanded to measure any target gas you choose.

The IAQ Survey Kit includes:

• Series 500 IAQ portable lightweight monitor

• Built-in temperature and humidity sensor

• Long life lithium battery for up to 8 hours in the field

• Onboard data logging

• High and low alarms

• Location ID to link measurements to location

• Rugged carry case to protect your equipment (optional)

• R42 calibration kit to allow regular calibration (optional)

• BUY our 3-in-1 multi-sensor head and get one single gas head absolutely free*

Sensor Heads Available 3-in-1: CO2, CO, VOC

2-in-1: CO2, CO Plus a full range of single gas sensor heads: Ammonia (NH3) Formaldehyde ( Hydrogen (H2) Hydrogen sulphide (H2S) Methane (CH4) Nitrogen dioxide (NO2) Non methane hydrocarbon (NMHC) Ozone (O3) Perchloroethylene Sulphur dioxide (SO2) See Sensor Specifications datasheet for full details

© Aeroqual Ltd, 2012 Aeroqual Limited IAQ Survey Kit April 2013


Series 500 IAQ Specifications

Measurement units Gas: ppm or mg/m3 | Humidity: % | Temperature °C or F

Reading functions Instant, minimum, maximum, average

Alarm features Low alarm, high alarm, mute (configurable)

Display status indicators Alarm, battery, datalogging, sensor, standby, monitor and location ID

Audible alarm Low and/or high alarm setpoints (with mute)

External signal functions Low alarm, high Alarm, control (150mA max)

Sensor calibration features Zero calibration, gain adjustment

Analog output 0-5V

Digital interface RS232 to USB

Data logging capacity Up to 8,188 records (2,706 incl. temp/RH)

PC data logging Software and data cable supplied

Clock function Real time

Power supply 12V DC (power adaptor/charger supplied 100-250V AC)

Rechargeable battery Lithium polymer 12V DC | 2700mA/h (2 hr charge time / 8 hr run time)

Enclosure material and rating PC and ABS; IP20 and NEMA 1 equivalent

Size (with sensor head) 195 x 122 x 54 (mm); 7⅝ x 4¾ x 2⅛ (in)

Weight (with sensor head and battery) < 460 g; < 16 oz

Environmental operating conditions Temperature: -5 oC to 45 oC ; Humidity: 0 to 95% non-condensating

Temperature & Humidity sensor Range -40°C to 124°C (-40°F to 255°F); Range 0 to 100% RH

Optional accessories Remote sensor kit, spare battery, car adaptor, wall bracket, carry case

Approvals Part 15 of FCC Rules; EN 50082-1: 1997; EN 50081-1: 1992

*Offer cannot be used in conjunction with any other promotional offer and is subject to review at any time. Excludes CO2, VOC (PID), MS1 / MS2 sensor heads.


All rights reserved www.aeroqual.com January 2013

Series 500

Portable Gas Monitor

The Series 500 monitor from Aeroqual is a feature-rich portable monitor with the ability to accurately measure multiple target gases at different concentrations in indoor and outdoor applications.

Built-in data-logging and a long-life, fast-charging lithium battery makes the Series 500 the ultimate choice for air quality professionals, consultants, and researchers.

• Built-in data-logging

• Lithium battery as standard

• PC software (Windows 7, 8, XP)

• Connect to PC via USB cable

• High and low alarms, control output

• Link data to a specific location and monitor

• Interchangeable gas sensor heads (30+ choices)

• Temperature and RH sensor optional (plug-and-play)

Specifications

Measurement units Gas: ppm or mg/m3 | Humidity: % | Temperature °C or F

Reading functions Instant, minimum, maximum, average

Alarm features Low alarm, high alarm, mute (configurable)

Display status indicators Alarm, battery, datalogging, sensor, standby, monitor and location ID

Audible alarm Low and/or high alarm setpoints (with mute)

External signal functions Low alarm, high Alarm, control (150mA max)

Sensor calibration features Zero calibration, gain adjustment

Analog output 0-5V

Digital interface RS232 to USB

Data logging capacity Up to 8,188 records (2,706 incl. temp/RH)

PC data logging Software and data cable supplied

Clock function Real time

Power supply 12V DC (power adaptor/charger supplied 100-250V AC)

Rechargeable battery Lithium polymer 12V DC | 2700mA/h (2 hr charge time / 8 hr run time)

Enclosure material and rating PC and ABS; IP20 and NEMA 1 equivalent

Size (with sensor head) 195 x 122 x 54 (mm); 7⅝ x 4¾ x 2⅛ (in)

Weight (with sensor head and battery) < 460 g; < 16 oz

Environmental operating conditions Temperature: -5 oC to 45

oC ; Humidity: 0 to 95% non-condensating

Optional accessories Remote sensor kit, spare battery, car adaptor, wall bracket, carry case

Temperature & Humidity sensor Range -40°C to 124°C (-40°F to 255°F); Range 0 to 100% RH

Approvals Part 15 of FCC Rules; EN 50082-1: 1997; EN 50081-1: 1992

Sensor Heads and Accessories

Sensor heads are available for these gases:

Ammonia (NH3)

Carbon dioxide (CO2)

Carbon monoxide (CO)

Hydrogen (H2)

Hydrogen sulphide (H2S)

Methane (CH4)

Nitrogen dioxide (NO2)

Non methane hydrocarbon (NMHC)

Ozone (O3)

Sulphur dioxide (SO2)

Volatile organic compounds (VOC)

Multi-sensor head: VOC / CO / CO2 or CO / CO2

See Sensor Specifications datasheet for details

Carry Case

Wall-mount bracket


All rights reserved www.aeroqual.com February 2013

Series 930

Gas Transmitter & Controller

The Series 930 is a networkable monitor with control and alarm outputs, all housed in a robust water resistant enclosure. By selecting one of our many interchangeable senor heads, the Series 930 can be used in a wide range of industrial applications including gas leak detection, health and safety, and process control. Gases available: Ammonia (NH3), Carbon Monoxide (CO), Formaldehyde (CH2O), Hydrogen (H2), Hydrogen Sulphide (H2S), Methane (CH4), Non-Metal Hydrocarbon (NMHC), Nitrogen Dioxide (NO2), Ozone (O3), Sulphur Dioxide (SO2), Volatile Organic Compound (VOC).

Features

• Active sampling for higher accuracy

• Tamperproof, water-resistant enclosure

• Multiple output transmitter

• Real-time network capability

• Data-logging and network software included

• Large LED local display option

• Temperature and RH sensor option

Specifications

Power (user supplied) 24V DC, 500mA (range 22-26V DC)

Analogue output 4-20mA (opto-isolated), 12-24V

External signal type Transistor output (150mA max)

External signals (4) Low Alarm | High Alarm | Control | Diagnostics

LED Display Optional

Inputs Standby toggle

Communication RS485 (Aeroqual proprietary protocol)

Jumpers J1, J2, J3 termination resistors

Connectors Screw

ID 1 (Default) User configurable from 1 to 255

Alarm set points (2) User configurable

Control set point User configurable

Removable / replaceable / refurbish-able sensor head Yes

Sampling method Active sampling via internal sensor fan

Temperature & humidity sensor (Series 945) Range -40°C to 124°C (-40°F to 255°F) | Range 0 to 100% RH

Configuration software (standard) PC Configuration Program CD (supplied)

Data logging & networking software (optional) PC Data Logging & Networking CD (code: R60)

USB interface (optional) RS485 to USB converter (code: R53)

Power supply (optional) 24V DC DIN rail mount 100-250V AC (code: R38)

Enclosure casing Fibre reinforced polycarbonate | IP41 & NEMA 2 equivalent

Enclosure size 180 x 110 x 90 (mm); 7⅛ x 4¾ x 3½ (in)

Weight < 850 g; < 30 oz

Approvals Part 15 of FCC Rules EN 50082-1: 1997 EN 50081-1: 1992


All rights reserved www.aeroqual.com MRK-D-0018 V1

Series 960H

High Ozone Transmitter

The Series 960H is a wall-mounted monitor that harnesses the benefits of UV photometry to deliver stable and reliable measurement and control in high ozone applications (up to 200 ppm). Applications include food storage, water treatment, building remediation and hospitals where high ozone concentrations are used for odor control, disinfection and sterilisation purposes.

Features

• High ozone measurement range (0-200 ppm)

• IP65 / NEMA 4 enclosure

• Single-beam UV photometer

• Pump sampling via PTFE tubing (e.g. monitoring outside of a room or duct)

• Multiple outputs (transistor, 4-20mA, RS485)

• PC and network software included

• LED display and Temperature/RH sensor options

Specifications Calibrated range 0-200 ppm Ozone

Accuracy <±5% of reading

Resolution 0.1 ppm

Minimum detection limit <0.1 ppm

Sampling method Brushless DC diaphragm pump

T90 <60s

Sample flow rate 0.4 ±0.05 LPM

Wetted materials PVDF, PFA, nafion, quartz, aluminium, viton

Inlet filter 5 µm pore size, 37 mm PTFE filter

Pneumatic connections Kynar ¼” compression fittings

Environmental operating conditions Temperature: 0-40°C ; Humidity: 0-95% RH (non-condensating)

Power requirements 24V DC, 2A

4-20mA display (optional) 3.5 digit LED (blue)

Analog output 4-20mA (opto-isolated) 12-24V DC (30V DC max) maximum loop resistance 500Ω at 24V, 16 bit resolution

Digital interface RS485 (2 wire) protocol supplied

Transistor outputs 4 x transistor outputs (Control, Diagnostics, High Alarm, Low Alarm)

User configurable set points Low alarm, High alarm, Control

Inputs Standby toggle (turns off pump)

Enclosure ABS Plastic, IP65 (Except inlet and exhaust)

Software Included for configuration, PC datalogging, and networking

DC relay board 2x SPDT 10A max switching current

Optional Accessories & Spares

FM DISP01 AS R53 AS R65 AS R66 AS R67 AS R68 AS R76

Integrated 4-20mA display LED 3.5 digit (blue) Serial RS 485 to USB Converter Replacement external filters (5 microns, hydrophobic, 12 per pack) PFA sampling tube 6.25 mm OD (per meter) Replacement UV lamp & block Replacement pump Replacement set of ozone scrubbers (3x)


All rights reserved www.aeroqual.com MRK-D-0010 V1

SM70

Wall-Mounted Gas Monitor

With an integrated LCD display, audible alarm, relay outputs, and a choice of sensor ranges in both ozone and VOC gases – the SM70 offers unbeatable value for industrial and indoor gas monitoring.

Benefitting from the accuracy of Aeroqual’s proprietary GSS sensors, our customers use the SM70 in many indoor and industrial applications including: leak detection, health and safety monitoring, and process control.

Features

• Large format digital display

• Replaceable GSS sensors

• External control outputs

• High and low alarms

• Power adaptor/charger included

Specifications

Sensor type Analytic GSS Technology® Gas Sensitive Semiconductor

Sensor specifications Available with ozone or VOC sensors in various ranges. Please refer to sensor specification table at www.aeroqual.com.

Sampling method Active sampling

Operational mode Continuous Control or Alarm

Operating temperature 0°C to 40°C

Operating relative humidity 10% to 90% non condensing

Warm up time 10 minutes

Display 3.5 digit LCD

Relay set point User configurable

Digital output RS232 and RS485

Analog output 0 - 5 VDC (8 bit)

Relay output 24 V; 5A (max.)

Buzzer alarm (optional) Internal piezo 85 db @ 30 cm

Power supply 12 VDC; 800 mA; Plug-in AC power adaptor supplied

Enclosure rating IP20 & NEMA 1 equivalent

Enclosure dimensions 130 W x 94 H x 57 D (mm); 5 ⅛ W x 3 ¾ H x 2 ¼ D (in)

Enclosure casing Flame resistant thermoplastic PS

Enclosure mounting Screw fix

Weight < 270 g; 9.5 oz (excludes AC power adaptor)

Approvals Part 15 of FCC Rules EN 61000-6-3: 2001 EN 61000-6-1: 2001