Fine movement occupancy sensor for HVAC and lighting control

training presence Control PRO IR Quattro COM1/COM2

Pammvi Group of CompaniesEmail: [email protected]: +91 22 2673 1904

Control PRO System

presence control PRO IR quattro HD presence control PRO HF 360presence control PRO DUAL HF


Control PRO System

fire control PROair control PRO


mounting

(1) Output module

(2) Sensor module

(10) Flush mounting box

(11) Surface mounting box

(IP 54)

(12) Lock mechanism

IP 54


presence Control PRO IR Quattro

• 1 pyro infrared sensor

• 1760 switching zones for very precise coverage

• room-typical, square detection zone

• Tangential: 7 x 7 m

• Radial: 5 x 5 m

• Presence: 4 x 4 m

• mechanical reach setting

• IP 20

• Accessories: surface mounting box (IP 54), flush mounting box with holding clamps, remote control RC3, remote control RC4, remote control RC5,

mounting height 3 m


functions IR Quattro COM1

(3) bottom side sensor module

(4) dip-switches

• Normal-/Test-mode

• full-/semiautomatic

• momentary switch/switch

• switch ON/ON-OFF

(5) twilight setting

(6) time setting switch contact 1

(9) mechanical reach setting



• 10 – 1000 lux with 6 typical room situations (stepless) (eg. 1 = corridor ca. 100 Lux)

• left stop night mode

• right stop day mode


• depending on occupancy and light level

• 30 sec. – 30 min.

• impulse modeeg. for stairway automats

• IQ-modeintelligent selflearning time setting dependingthe specific pattern of room use




(4) Dip-switches


Test-mode:

- load independent test-mode - 8 sec. ON- without connected load adjustable- blue LED blink at detection - to proof functionality and detection zone

Normal-mode:

- works depending on settings by trimpods and dip-switches



(4) dip-switches


fullautomatic:

- automatic ON / automatic OFF depending on occupancy and light level

- manual control possible

semiautomatic:

- manual ON / automatic OFF

- manual OFF possible

- after using a switch lights switch ON and sensor mode starts depending on trimpod and dip switch setting



(4) dip-switches


momentary switch:

- use with external momentary switch

switch:

- use with external switch



(4) dip-switches

• ON/ON-OFF

ON:

- no manuall OFF possible

- push on switch restarts run down time

ON-OFF:

- manual ON & OFF possible




• 7 „orientation points“ on bottom side of the sensor

• at a mounting height of 3 m the number chosen with the trimpod means the length of the square side for tangential detection

• „translation table“ for different mounting heights and radial respectively presence detection in the owners manual



(3) bottom side sensor module

(4) dip-switches




• switch ON/ON-OFF



(7) time setting switch contact 2 (PF)

(8) time delay switch contact 2




(7) time setting switch contact 2 (PF)

- run down time of the hvac Schaltkontakts von 1 Min. bis 2 Stunden

(8) time delay switch contact 2 (PF)

- switch-on delay switch contact 2 from 30 sec. to 10 min.

- room observation

- only if the room is used really the hvac contact will be switched

- a short look into the room will be ignored


crosslinking of the sensors

Master/Slave:

- Slaves only report occupancy to the Master

- only the Master switches the load

- switching only depending on the Master settings

Master/Master:

- all Masters report occupancy to each other

- every Master switches ist own load depending on ist own settings

Master: load connected

Slave: no load connected


functions remote control RC3 (service)

reach setting HF/US sensors

Reset to trimpod & dip settings

Teach IN

twilight setting

Reduce sensitivity

time setting switch contact 2 (hvac)

time setting switch contact 1 (light)


functions remote control RC4 (DIM)


4 hours manual override

set dimming level


functions remote control RC5 (DALI)


Save/load scene

set dim level

Manual override

set dim level

Manual override


USP´s

precise coverage by 1760 switching zones

IR Quattro


USP´s

very precise coverage by more than 4000 switching zones

IR Quattro HD


USP´s

coverage of different presence detectors (presence detection area)

STEINEL IR Quattro STEINEL IR Quattro HD standard motion detector

Busch Jäger PräsenzTech


USP´s

more than 4000 switching zones for very precise coverage


USP´s

more than 4000 switching zones for very precise coverage


USP´s

roomtypical square detection

7m

7m

detection reach (mounting height 3m):

- squares: Steinel IR Quattro- circles: competitors presence detector

- inner area: presence detection

Steinel: 4x4m detection squarecompetitor: circle Ø 4m

- middle area: radial detectionSteinel: 5x5m detection squarecompetitor: circle Ø 6m

- outer area: tangential detectionSteinel: 7x7m detection squarecompetitor: circle Ø8m


USP´s



USP´s



auch Bereiche innerhalb der einzelnen Bürosnicht erfasst

USP´s



USP´s

mechanical reach setting

-


USP´s

tangentiale Erfassung

radiale Erfassung

Präsenzerfassung

- Reduzierung auf den reinen - alle Erfassungsbereiche werden elektronischPräsenzbereich runtergeregelt, so dass der Präsenzbereich

- radiale und tangentiale Erfassung auf Ø 2m eingeschränkt wirdwerden "abgeschnitten" - radiale und tangentiale Erfassung bleibt vorhanden!

reduziert auf 4 x 4 m reduziert Ø 4m

mechanical reach setting

reduced to 4x4m reduced to Ø 4m

tangential detection

radial detection

presence detection

- reduced to presence detection only

- radial & tanegntial detection are „cut off“

- all detection zones are sized down detection only

- radial & tanegential detection are „cut off“


Ausblick

sensor modules:

IR Quattro (1 Pyro)

IR Quattro HD (4 Pyros)

HF 360° (HF bar antenna)

DUAL HF (2 HF Patch antennas)

AirControl

FireControl

output modules:

COM1 (1 Relais)

COM2 (1+1 PF Relais)

DIM (1-10V)

KNX

DALI

Impulser

flat surface mounting version

Accessories: surface mounting adapter (IP 54), surface mounting adapter KNX/DALI, flush-mounting adapter (with holding clamps), service remote control, DIM remote control, DALI remote control, protection basket

Technology

Fine movement occupancy sensor for HVAC and lighting control