Device configuration guide_7.41

WWW.ANITE.COM/NEMO

© Anite 2014

DEVICE CONFIGURATION GUIDE

DOCUMENT NUMBER NNNNNNNNN ISSUE N


Page 2

Copyright

The information contained in this document is confidential and no part of it may be copied or reproduced in any form without the written consent of Anite Network Testing. Additionally, this document is not to be passed to or discussed with third parties without the prior written permission of Anite Network Testing.

Anite’s products are subject to continual development and specifications may change. Users of Anite’s products and documentation should exercise their own independent judgement to evaluate the suitability of Anite’s products and documentation for their particular use. Anite does not accept any liability arising from the application or use of the product or this documentation.

All reasonable care has been made to ensure that this document is accurate. If you have any comments on this document, or would like details of any Anite products, services or equipment, please contact us through the Anite website.


Page 3

CONTENTS

1 INTRODUCTION ............................................................................................... 6

1.1 Device autodetection ................................................................................ 6 1.2 Manual configuration of dial-up connection ................................................... 7

2 APPLE IPHONE 5 ............................................................................................. 11

3 BANDRICH BANDLUXE C320 ............................................................................. 12

4 BLACKBERRY TORCH 9810 ............................................................................... 14

5 DATANG DTM8101/DTM8120/ LEADCORE LC8130E .............................................. 17

6 HTC ONE XL ................................................................................................... 19

7 HTC ONE M8 .................................................................................................. 24

8 HUAWEI E180/E169/E182E/E1820 /E270+/E367/E392U-12/E372U-8 USB MODEM ... 31

9 HUAWEI E392U-12 .......................................................................................... 33

9.1 Changing TCP/IP Properties ...................................................................... 34

10 HUAWEI C7600 ............................................................................................... 36

11 HUAWEI E398 ................................................................................................ 39

11.1 Changing TCP/IP Properties ...................................................................... 39

12 KODIAK PTT ................................................................................................... 42

12.1 Driver installation .................................................................................... 42 12.2 Pairing the phone with the laptop .............................................................. 44 12.3 Configure and connect Kodiak PTT client via Bluetooth .................................. 46 12.4 Adding Kodiak PTT device in Nemo Outdoor ................................................ 48

13 NETGEAR AIRCARD 340U ................................................................................. 49

14 NETGEAR AIRCARD 782S ................................................................................. 51

15 NOKIA LUMIA 920 (RM-821) ............................................................................. 53

16 NOKIA 3500/6120/6121/ 6720(US)/C5/C5-00.2/C5-03(US)/ C5-04/C7-00/E7-00/N80/ N85(US)/N95(US)/N96(US)/ N97(US) .................................................................... 55

17 NOKIA 500 .................................................................................................... 58

18 NSN USB-LTE 7210 (ALTAIR) ............................................................................ 60


Page 4

19 MOTOROLA USBW 25100 ................................................................................. 64

20 SAMSUNG GALAXY CORE (SM-G386F) ............................................................... 66

21 SAMSUNG GALAXY S4 (GT-I9505, SGH-I337, SPH-L720, SGH-M919, SCH-R970, SGH-M919N, SGH-I337M), GALAXY S4 ACTIVE (GT-I9295), GALAXY S II (GT-I9210) .......... 68

22 SAMSUNG GALAXY S II SKYROCKET, GALAXY S II HD LTE (SHV-E120S KOREAN VERSION) .................................................................................................... 70

23 SAMSUNG GALAXY S III (SGH-I747, SGH-T999, SCH-I535, SPH-L710), GALAXY RUGBY, GALAXY S4 MINI (GT-I9195, SPH-L520), GALAXY S4 4G+ (GT-I9506), GALAXY NOTE 3 (SM-N9005, SM-N900T, SM-N9008V, SM-N9007), GALAXY NOTE 3 LITE (SM-N7509V), GALAXY NOTE 4 (SM-N910F, SM-N910G), GALAXY S5 (SM-G900F, SM-G900I, SM-G900P, SM-G900A, SM-G900T, SM-G900W8, SM-G9006V, SM-G900V, SM-G900T1, SM-G900R4, SM-G9009W, SM-G9008V) ................................................................. 72

24 SAMSUNG GALAXY S III (GT-I9305), GALAXY II NOTE (GT-N7105) ........................ 75

25 SAMSUNG DROID CHARGE ............................................................................... 78

26 LG C676/C680/VX8300/U900/ KU950/KX206/KX256/KF700/ TU550 ....................... 80

27 LG VX8350/VX8360 ......................................................................................... 84

28 LG L1000 .................................................................................................... 87

29 LG P930, G2 ................................................................................................... 89

30 HUAWEI E3276S-150/861 ................................................................................ 91

31 HUAWEI ASCEND P2 ........................................................................................ 93

32 LG P500H .................................................................................................... 96

33 SIERRA WIRELESS AIRCARD 306/307/308/309/310U/ 312U/313U/320U/330U, SIERRA COMPASS 889, SIPTUNE SM215 ............................................................................ 97

34 SIERRA WIRELESS COMPASS 597 ................................................................... 100

35 NOVATEL OVATION MC930D/MC990D/MC996D/ MC998D/MC545 ......................... 102

36 NOVATEL OVATION MC727/MC760 .................................................................. 104

37 PANTECH UM175 .......................................................................................... 106

38 PANTECH UML290 ......................................................................................... 109

39 ZTE MF820T/MF820D .................................................................................... 112

40 ZTE MF668A ................................................................................................. 113

41 ZTE MF683 .................................................................................................. 114

42 ZTE MF880 .................................................................................................. 115

43 ZTE TU25 .................................................................................................. 116


Page 5

44 SONY ERICSSON XPERIA ARC S ...................................................................... 118

45 ONDA MT689DC............................................................................................ 126

46 APPLICATION TESTER .................................................................................... 128

47 TECHNICAL SUPPORT .................................................................................... 129

47.1 User Club ............................................................................................. 129 47.2 Nemo Support Portal ............................................................................. 129 47.3 Phone and Email Support ....................................................................... 129


Page 6

1 INTRODUCTION

The purpose of this document is to give step-by-step instructions for setting up test devices for data testing with Nemo tools.

♦ Please note that the devices below have been removed from the current document. Configuration instructions for these devices can be found in the Dial-up Networking Setup Guide version 7.10.

• Audiovox PC5750/Pantech PX-500

• Huawei EC169/EC169C USB Modem

• LG G7/G13/G17

• LG VL600

• LG U900/KU950

• Merlin U530/U740/X950D

• Motorola V3x/V3XX/V3XXUS/V9/V9US

• Nokia 6230i

• Option GlobeTrotter 3G+/GT MAX 7.2 Ready/HSDPA 7.2/Express 7.2

• Option iCon 452

• Option GlobeSurfer iCON 7.2 USB modem

• Qualcomm TM6250/6275/6280/7200/8200/ MDM9200/MDM9600

• Samsung Z105/Z107/Z140/Z500/Z560/Z720/ZV10/ZX20/A707/G800/P920/P940/SHG-T639/SGH-U800/SHG-U900

• Sierra Wireless Aircard 850/860

• Sierra Wireless Aircard 880/881

• Sierra Wireless Compass 885

• Zapp Telemodem Z020

1.1 Device autodetection

From Nemo Outdoor 5.60 onwards, it is possible to use autodetection to add devices to Nemo Outdoor. It is no longer necessary to manually configure a dial-up connection. Once a device is connected to a computer and the device driver is installed, it can be added fully automatically to Nemo Outdoor using the Autodetect Devices button. Nemo Outdoor will automatically detect the device trace and modem ports and assign a suitable dial-up connection.

Autodetection works with all Nemo Outdoor test terminals verified by Anite Network Testing. In some cases it is possible that the terminal is not recognized and the autodetection does not work. If this happens, manually select the correct trace and modem ports. Then select Automatic in the


Page 7

Packet switched dial-up connection field and click Apply. If the automatic dial-up connection detection does not work, please see instructions below.

1.2 Manual configuration of dial-up connection

1. Select Start | Control Panel | Network and Internet. Select Network and Sharing Center | Set up a new connection or network. Select Set up a dial-up connection, and click Next.

2. Select the correct terminal from the list and click Next. With Nokia terminals, select the item with the highest number, e.g., in this case #3.


Page 8

3. In the Telephone Number field, enter *99# (#777 for CDMA terminals). In the Connection name field type, for example, Nokia Dial-up connection. Select Allow other people to use this connection. Click Connect.

4. Click on Skip in the Connecting to xxx dial-up connection dialog.


Page 9

5. Click Close.

6. Go to Control Panel | Network and Internet | Network and Sharing Center, and select Connect to a network. Right-click on the Terminal Dial-up Connection, and select Properties.

7. In the Networking tab, deselect the Internet Protocol Version 6 (TCP/IPv6) item and select Internet Protocol Version 4 (TCP/IPv4). Click OK.

♦ Steps 8 and 9 apply only to Nokia terminals.


Page 10

8. Go to Device Manager (Start | Settings | Control Panel | System and Security | Device Manager), and double-click on Modems. Right-click on the #3 item on the list and click Properties.

9. Select the Advanced tab, and type in atz in the Extra initialization commands field, and click on OK.

10. See the following chapters for terminal-specific instructions on adding terminals to Nemo Outdoor.


Page 11

2 APPLE IPHONE 5

Apple iPhone 5 can be connected with Nemo Outdoor using the application tester handler.

1. Install iTunes on your computer. iTunes can be downloaded from http://www.apple.com/itunes/download. Start iTunes.

2. On the iPhone 5 device, select Settings | Personal Hotspot and turn on the Personal Hotspot.

3. Connect the USB connectivity cable to your PC. Device drivers are installed automatically.

4. Go to Nemo Outdoor and select Measurement | Add New Device | Phone | Application Tester.

5. Leave the Trace Port and Modem Port fields empty.

6. Select <LAN> as the Packet switched dial-up connection. Click OK.

♦ Activate a packet session manually before running scripts.

♦ Note that when testing with iPhone 5, all other connections (WLAN, Ethernet cable, etc.) need to be disconnected.

http://www.apple.com/itunes/download


Page 12

3 BANDRICH BANDLUXE C320

1. Plug in the USB device in one of your PC’s USB ports. The drivers are automatically installed, and Windows automatically detects the device.

2. Select English in the Choose Setup Language dialog.

3. Click on Next in the Welcome dialog that appears.

4. Select I accept the terms in the license agreement in the License Agreement dialog, and click Next.

5. Select a destination folder and click Next.

6. Click Install to start the installation and click Finish to finish the installation.

7. Close the BandLuxe software that appears, as it will not be required in the following steps.


Page 13

8. Go to Start | Control Panel | System | Hardware | Device Manager. Under Modems you should be able to see the BandLuxe 3.5G Modem, under Network adapters you should see the BandLuxe 3.5G Ethernet Adapter, and under Ports the BandLuxe Adapter Control Interface (COMxx) and BandLuxe AT CMD Interface (COMxx) items.

9. In Nemo Outdoor Device Configuration dialog, select the COM port number assigned to the BandLuxe Adapter Control Interface item in the Trace Port field. Select the COM port number assigned to the BandLuxe 3.5G Modem item (right-click the item and select Properties) in the Modem Port field.


Page 14

4 BLACKBERRY TORCH 9810

♦ Please note that currently the driver can be installed on 32-bit Windows only.

♦ Install the device drivers. The file is located on the Nemo Outdoor USB flash drive. Browse the file manually and double-click the 610_b038_multilanguage file. The package will self-extract.

1. The Blackberry Desktop Software application is launched. Select the installation language and click OK.

2. If the installer requests to install the Microsoft Visual C++ 2008 Redistributable file, click Install.

3. Click Next to begin the Blackberry Desktop SW installation.

4. Select your country or region and click Next.

5. Accept the license agreement and click Next.

6. Select the installation folder and click Next and Install.

7. Wait until the installation is complete and click Finish.

8. Close the Blackberry software that appears, as it will not be required in the following steps.


Page 15

9. Go to Device Manager. Under Modems you should see the Standard Modem item and under Ports two RIM Virtual Serial Port v2 items.

10. Connect the device USB cable to the device and to the Nemo Outdoor laptop. Select USB Drive from the device screen.

11. Start Nemo Outdoor. Autodetection does not work with the Blackberry device so add the device manually (Add New Device | Phone | Qualcomm).


Page 16

12. In the Device Configuration dialog, select the COM port with the bigger number assigned to the RIM Virtual Serial Port v2 item in the Trace Port field. Select the COM port with the smaller number in the Modem Port field. Select Automatic in the dial-up connection field.


Page 17

5 DATANG DTM8101/DTM8120/ LEADCORE LC8130E

♦ Do not connect the connectivity cable to your PC until the driver installation is complete.

1. The connectivity cable driver is located on the Nemo Outdoor USB flash drive. Browse the file manually and double-click the USB2VCOM_driver_x.xx.xx file (x is the latest driver version).

2. Select Uninstall old version first if installed, and click Install in the Leadcore Technology DTM8100 Series Driver Installer dialog.

3. In the VCOM Number field you need to select 3 ports for each test terminal. Since the driver is installed only once, select the number of COM ports according to how many Leadcore terminals you intend to use with Nemo Outdoor. Hence, if you want to connect two Leadcore terminals with Nemo Outdoor, select at least 6 in the VCOM Number field. Click Exit when the installation is done.

4. After the driver installation is finished, Windows may restart your computer but it is not required.

5. After your computer has restarted, connect the connectivity cable to the mobile and the other end to the computer’s USB port. Windows will detect the new hardware automatically and start the installation. The step is repeated several times until all new hardware is added.

6. In the Welcome page, select No, not this time and click Next.

7. Select Install the software automatically (Recommended) and click Next.


Page 18

8. Click Yes or Continue Anyway in the Digital Signature Not Found or Hardware Installation dialog if it appears. You may need to repeat steps 6, 7 and 8 several times until the installation process is finished.

9. After installation, go to Device Manager. Select Start | Settings | Control Panel | System, open the Hardware tab and click the Device Manager button.

10. You should be able to see three Datang Mobile modems under Modems, and three Datang Mobile items under Ports.

11. Start Nemo Outdoor. Select View | Windows Device Manager. From the Device Manager you will find the COM port numbers needed in the next steps.

12. Select Measurement | Add New Device. In the New Device dialog, click Phones and select the terminal. Click Next.

13. In the Device Manager click on Ports. Select the COM port number assigned to the Leadcore Technology DTM8100 Modem #2 item In the Trace Port field in the Device Configuration dialog. Select the COM port number assigned to the Leadcore Technology DTM8100 Modem #3 item in the Modem Port field.

14. In the Device Configuration dialog, select <Automatic> or the previously made dial-up connection as the Packet switched dial-up connection (see page 6). Click Apply.

15. If the device connecting fails, check that you have selected the correct COM ports and try again.


Page 19

6 HTC ONE XL

1. Connect the device to the laptop. Select Charge only on the phone.

2. Go to Device Manager. Under Other devices you should see the HTC DIAG, HTC Modem, and RmNet items.

3. Right-click on the HTC DIAG item and select Update Driver Software.


Page 20

4. In the Update Driver SW – HTC DIAG dialog, select Browse my computer…

5. Select Let me pick from a list…


Page 21

6. Select Show All Devices and click Next.

7. Click Have Disk.

8. On the Nemo Outdoor product package, browse to folder Drivers\Qualcomm\HTC_One_XL\DIAG and select the correct subfolder based on your operating system, e.g. \Win7_x86. Click OK.


Page 22

9. Click Next.

10. If the Windows Security dialog appears, click Install this driver anyway. The driver will be installed. Click Close after the installation is finished.

11. The HTC DIAG item has disappeared and a new item HTC Diagnostic Interface appears under Ports.

12. Now repeat the driver software update process for the HTC Modem and RmNet items. Ignore all Windows warnings. The steps are otherwise the same but the driver files are located in different folders:


Page 23

• HTC Modem: Drivers\Qualcomm\HTC_One_XL\Modem

• RmNet: Drivers\Qualcomm\HTC_One_XL\QMI

13. After you have updated all drivers, go to Device Manager. You should see the following items:

• Modems: HTC USB Modem

• Network adapters: HTC Ethernet Adapter

• Ports: HTC Diagnostic Interface

14. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device dialog, click Phones and select the Qualcomm item. Click Next.

15. In the Nemo Outdoor Device Configuration dialog, define the following settings:

• Trace port: Select the COM port number assigned to the HTC Diagnostic Interface.

• Modem port: Select the COM port number assigned to HTC USB Modem

• Packet-switched dial-up connection: NDIS

16. Click Apply.



Page 24

7 HTC ONE M8

1. Connect the device to the laptop. Select Charge only on the phone.

2. Go to Device Manager. You should see the following items:


• Network adapters: HTC Remote NDIS based Device


3. You can now jump to step 17.

4. If these items are not visible, you will need to update the drivers. See the following step.


Page 25

5. Under Other devices you will see the HTC DIAG, HTC Modem, and RmNet items.

6. Right-click on the HTC DIAG item and select Update Driver Software.


Page 26

7. In the Update Driver SW – HTC DIAG dialog, select Browse my computer…

8. Select Let me pick from a list…


Page 27


10. Click Have Disk.


Page 28

11. On the Nemo Outdoor product package, browse to folder Drivers\Qualcomm\HTC_One_XL\DIAG and select the correct subfolder based on your operating system, e.g. \Win7_x86. Click OK.

12. Click Next.

13. If the Windows Security dialog appears, click Install this driver anyway. The driver will be installed. Click Close after the installation is finished.


Page 29

14. The HTC DIAG item has disappeared and a new item HTC Diagnostic Interface appears under Ports.

15. Now repeat the driver software update process for the HTC Modem and RmNet items. Ignore all Windows warnings. The steps are otherwise the same but the driver files are located in different folders:

• HTC Modem: Drivers\Qualcomm\HTC_One_XL\Modem

• RmNet: Drivers\Qualcomm\HTC_One_XL\QMI


Page 30

16. After you have updated all drivers, go to Device Manager. You should see the following items:


• Network adapters: HTC Remote NDIS based Device




• Trace port: Select the COM port number assigned to the HTC Diagnostic Interface.

• Modem port: Select the COM port number assigned to HTC USB Modem

• Packet-switched dial-up connection: HTC Remote NDIS based Device

19. Click Apply.



Page 31

8 HUAWEI E180/E169/E182E/E1820 /E270+/E367/E392U-12/E372U-8 USB MODEM

♦ Applies to all 3G and 4G Huawei USB modems. The Huawei Connection Manager starts up every time the device is plugged in and it must be closed in order to be able to use the device with Nemo Outdoor. As a workaround, the Connection Manager .exe file can be renamed. A reinstall warning will be displayed when device is plugged in but this can be ignored.


2. Next, ignore and close the Vodafone or Mobile Partner application that appears. It should not be on while connecting the device with Nemo Outdoor later on.

3. You may need to restart the computer for the installation to take effect.

4. Go to Start | Control Panel | Phone and Modem Options | Modems. You should see the Huawei Mobile Connect – 3G Modem item with its associated COM port number in the list.

♦ Please note that with some Huawei E392U-12 devices the Huawei Mobile Connect – 3G Modem item does not appear. If this happens, please follow the instructions in chapter Huawei E392u-12.


6. Select Measurement | Add New Device. In the New Device dialog, click Phones and select the Qualcomm item. Click Next.


Page 32

7. In the Device Manager click on Ports. Select the COM port number assigned to the Huawei Mobile Connect – 3G Application Interface item In the Trace Port field in the Device Configuration dialog. Select the COM port number attached to the Huawei Mobile Connect – 3G Modem item in the Modem Port field.




Page 33

9 HUAWEI E392U-12

♦ Please note that with some Huawei E392U-12 devices the Huawei Mobile Connect – 3G Modem item does not appear. If this happens, please follow the instructions below.

♦ The Huawei Connection Manager starts up every time the device is plugged in and it must be closed in order to be able to use the device with Nemo Outdoor. As a workaround, the Connection Manager .exe file can be renamed. A reinstall warning will be displayed when device is plugged in but this can be ignored.


2. Next, ignore and close the Vodafone or Mobile Partner application that appears. It should not be on while connecting the device with Nemo Outdoor later on.

3. You may need to restart the computer for the installation to take effect.

4. Start Nemo Outdoor. Select View | Windows Device Manager. In the Device Manager, you should see the following two items and their COM port numbers under Ports: Huawei Mobile Connect – Application Interface and Huawei Mobile Connect – PC UI Interface.


6. In the Device Manager click on Ports. Select the COM ports as follows:

• Trace port: Huawei Mobile Connect – Application Interface

• Modem port: Huawei Mobile Connect – PC UI Interface



Page 34


9.1 Changing TCP/IP Properties

♦ Applies to all 3G and 4G Huawei USB modems with Nemo Outdoor 6.30 and older versions. Before measurements can be done with Nemo Outdoor, the Internet protocol properties must be manually changed to automatic mode. This must be done always after the modem is disconnected/reconnected and also if the device stops responding during measurements.

∇ Windows XP:

1. Plug in the Huawei device.

2. Go to Start | Control Panel | Network Connections, and right-click on Huawei Broadband Connection, and select Properties.

3. In the Mobile Broadband Connection Properties dialog, select Internet Protocol Version 4 (TCP/IPv4) and click on Properties.

4. Select Obtain an IP address automatically and Obtain DNS server address automatically.

∇ Windows 7:


2. Go to Start | Control Panel | Network and Internet | Network and Sharing Center.

3. Click on Change adapter settings.

4. Right-click on Mobile Broadband Connection and select Properties.


Page 35


6. Select Obtain an IP address automatically and Obtain DNS server address automatically. Click OK and OK.


Page 36

10 HUAWEI C7600

♦ Do not connect the USB data cable to your PC until the driver installation is complete.

1. The data cable driver is located on the Nemo Outdoor USB flash drive. Browse to folder D:\Drivers\Drivers for Qualcomm Based Devices\Huawei C7600 and run the driver .exe file.

2. Click Install in the DriverInstall Setup: Installation Options dialog.

3. Click Close in the DriverInstall Setup: Completed dialog.


Page 37

4. After the installation has finished, connect the USB connectivity cable to your phone, and the other end of the cable to your computer’s USB port. Windows will detect the new hardware automatically and start the installation.



7. Click Yes or Continue Anyway in the Digital Signature Not Found or Hardware Installation dialog if it appears. You may need to repeat steps 5, 6 and 7 several times until the installation process is finished. Click Finish to exit the wizard.



Page 38

9. You should see the HUAWEI CDMA Handset – Modem item under Ports.



12. In the Device Manager click on Ports. Select the COM port number assigned to the Huawei CDMA Handset – Application Interface item In the Trace Port field in the Device Configuration dialog. Select the COM port number attached to the Huawei CDMA Handset - Modem item in the Modem Port field.




Page 39

11 HUAWEI E398

♦ Applies to all 3G and 4G Huawei USB modems. The Huawei Connection Manager starts up every time the device is plugged in and it must be closed in order to be able to use the device with Nemo Outdoor. As a workaround, the Connection Manager .exe file can be renamed. A reinstall warning will be displayed when device is plugged in but this can be ignored.

1. Connect the device to your computer’s USB port. Windows will detect the new hardware automatically and start the installation. Click Run AutoRun.exe and follow the instructions on the screen.

2. The Telenor Mobile Partner software starts up. Close the program.


4. You should see the Huawei Mobile Connect – Modem item under Modems and the Huawei Mobile Connect – Application Interface and Huawei Mobile Connect – PC UI Interface items under Ports.



7. In the Device Manager click on Ports. Select the COM port number assigned to the Huawei Mobile Connect – PC UI Interface item In the Trace Port field in the Device Configuration dialog. Select the COM port number assigned to the Huawei Mobile Connect - Modem item in the Modem Port field.

8. In the Device Configuration dialog, select <NDIS> as the Packet switched dial-up connection. Click Apply.


11.1 Changing TCP/IP Properties

♦ Applies to all 3G and 4G Huawei USB modems with Nemo Outdoor 6.30 and older versions. Before measurements can be done with Nemo Outdoor, the Internet protocol properties must be manually changed to automatic mode. This must be done always after the modem is disconnected/reconnected and also if the device stops responding during measurements.


Page 40

∇ Windows XP:


2. Go to Start | Control Panel | Network Connections, and right-click on Huawei Broadband Connection, and select Properties.


4. Select Obtain an IP address automatically and Obtain DNS server address automatically.

∇ Windows 7:


2. Go to Start | Control Panel | Network and Internet | Network and Sharing Center.

3. Click on Change adapter settings.

4. Right-click on Mobile Broadband Connection and select Properties.


Page 41


6. Select Obtain an IP address automatically and Obtain DNS server address automatically. Click OK and OK.


Page 42

12 KODIAK PTT

12.1 Driver installation

1. The first step is to install drivers for the Bluetooth adapter. The driver file (IOGEAR Bluetooth 4.0 USB Micro Adapter GBU521 Driver Win Vista 7 v6.5.1.2700) can be downloaded from the Nemo User Club (nemouserclub.anite.com) or from http://www.iogear.com/support/dm/driver/GBU521#display

2. Run the Autorun.exe file.

3. Wait until the driver has been installed.

4. Agree to install the Bluetooth service.

5. Plug in the USB to Bluetooth module to your Nemo Outdoor laptop when prompted.

6. When installation is ready, press Finish.

7. Go to Control Panel | Hardware and Sound | Devices and Printers. You should see the BCM920702 Bluetooth 4.0 device.

http://www.iogear.com/support/dm/driver/GBU521#display


Page 43

8. Right click the Bluetooth device and select Bluetooth settings.

9. Select the Show the Bluetooth icon in the notification area option.


Page 44

12.2 Pairing the phone with the laptop

1. Check the computer name from the Device Manager.

2. Enable Bluetooth on your Kodiak PTT phone.

3. Enable your device visibility.

4. Select Add a Device from the Bluetooth menu on your laptop and follow the wizard to add the phone.


Page 45

5. Confirm the pairing code and click Next.

6. You should now see your phone as a device in the Devices and Printers view.


Page 46

12.3 Configure and connect Kodiak PTT client via Bluetooth

1. Launch the Kodiak PTT client on the phone.

2. On your laptop, go to Control Panel - Hardware and Sound, right-click the device (your phone) and select Properties.

3. On the Services page, select the Serial port (SPP) ‘KodiakPoCApplication’ option.

4. Click OK and a Bluetooth serial port will be installed.


Page 47

5. Go back to the PTT1 Properties, Services page. You should now see a COM port assigned for the Serial port.

6. You should also see a COM port under Ports in Device Manager.


Page 48

12.4 Adding Kodiak PTT device in Nemo Outdoor

1. Device can be added using either the terminal specific handler or the Application Tester handler. These steps will show the usage with the Application Tester handler.

2. Launch Nemo Outdoor.

3. Add a new device (Application Tester) and click Next.

4. In the Kodiak PTT port field, select the COM port that was assigned for the Standard Serial over Bluetooth link item (check from Device Manager, Ports).

5. When using the Application Tester handler, there is no need to configure the Trace or Modem ports. Also dial-up connections can be “Not Used” if only Kodiak testing will be performed.

6. Press OK to add the device. You are now ready to start the measurements.


Page 49

13 NETGEAR AIRCARD 340U


2. Go to Network adapter settings and select Never connect automatically in the Autoconnect field.


Page 50

3. After installation, go to Device Manager. You should see the following items: Modems: Sierra Wireless WWAN Modem Ports: Sierra Wireless DM Port



• Trace port: Select the COM port number assigned to Sierra Wireless DM Port

• Modem port: Select the COM port number assigned to Sierra Wireless WWAN Modem

6. In the Device Configuration dialog, select <NDIS> or the previously made dial-up connection as the Packet switched dial-up connection (see page 6). Click Apply.



Page 51

14 NETGEAR AIRCARD 782S

♦ Do not connect the USB connectivity cable to your PC until the driver installation is complete.

1. The connectivity cable driver is located on the Nemo Outdoor USB flash drive. Browse to folder Nemo Outdoor xxx\Drivers\Qualcomm\Netgear\Netgear Aircard 782S\ AC78xSDrivers_B3978_3.exe and run the .exe file.

2. Follow the instructions in the installation wizard to finish the driver installation.

3. Connect the connectivity cable to the mobile and the other end to the computer’s USB port. Windows will detect the new hardware automatically and install the necessary drivers.

4. After installation, go to Device Manager. You should see the following items: Modems: Netgear WWAN Modem Ports: Netgear DM Port



• Trace port: Select the COM port number assigned to Netgear DM Port

• Modem port: Select the COM port number assigned to Netgear WWAN Modem


Page 52




Page 53

15 NOKIA LUMIA 920 (RM-821)


1. First, uninstall any existing Qualcomm drivers.

2. The connectivity cable driver is located on the Nemo Outdoor USB flash drive. Browse to folder Nemo Outdoor\Nemo Outdoor x.x\Drivers\Qualcomm\Nokia\Lumia 920 RM-821\USB Host Driver 1.00.12\72 and run the setup.exe file.

3. Click Next in the Welcome dialog. Select I accept… in the License Agreement dialog and click Next.

4. Click Install and finally Finish.

5. After the connectivity cable driver installation is finished, Windows may restart your computer but it is not required.


♦ Please note that with newer Nokia devices the Wizard may not appear at all and instead the installation is performed automatically.



9. Click Yes or Continue Anyway in the Digital Signature Not Found or Hardware Installation dialog if it appears. You may need to repeat steps 8, 9, and 10 several times until the installation process is finished.


Page 54

10. After installation, go to Device Manager. You should see the following items: Modems: Qualcomm HS-USB Modem 9001 Network adapters: Qualcomm HS-USB WWAN Adapter Modem 9001 Ports: Qualcomm HS-USB Diagnostics 9001



• Trace port: Select the COM port number assigned to Qualcomm HS-USB Diagnostics 9001

• Modem port: Select the COM port number assigned to Qualcomm HS-USB Modem 9001




Page 55

16 NOKIA 3500/6120/6121/ 6720(US)/C5/C5-00.2/C5-03(US)/ C5-04/C7-00/E7-00/N80/ N85(US)/N95(US)/N96(US)/ N97(US)


♦ With Nokia C5-03(US), C5-04, C7-00 and E7-00 the following settings are recommended to improve stability:

• Set Theme effects to OFF

• Set Animated background to OFF

• Set Call image to none

• Set Screen saver to none

• Delete additional home screens

• Set widgets to offline mode

• Set WLAN scanning to OFF

• Set sensors to OFF

1. The connectivity cable driver is located on the Nemo Outdoor USB flash drive. Browse to folder Nemo Outdoor x.xx\Drivers\Nokia drivers and run the Nokia_Connectivity_Driver_xxx.x.msi file (x is the latest driver version).

2. Click Next in the Welcome dialog. Select I accept… in the License Agreement dialog and click Next.

3. Please read the safety notes carefully and then click Next in the Safety Information dialog.

4. Choose the destination folder and click Install.

5. Click Yes in the Digital Signature Not Found dialog if it appears. Otherwise, click Install.

6. After the connectivity cable driver installation is finished, Windows may restart your computer but it is not required.


♦ Please note that with newer Nokia devices the Wizard may not appear at all and instead the installation is performed automatically.


Page 56



10. Click Yes or Continue Anyway in the Digital Signature Not Found or Hardware Installation dialog if it appears. You may need to repeat steps 8, 9, and 10 several times until the installation process is finished.



Page 57

12. Under Wireless Communication Devices you should see the Nokia xxxx USB Phone Parent item. Under Modems, you should see three Nokia xxxx (USB) items. Leave the Device Manager open as you will find there the COM port numbers needed in the next steps.

13. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device dialog, click Phones and select the terminal. Click Next.

14. In the Device Manager click on Modems. Select the COM port number assigned to the first/unnumbered Nokia xxx USB item In the Trace Port field in the Device Configuration dialog. Select the COM port number assigned to the second highest Nokia xxx USB item in the Modem Port field.




Page 58

17 NOKIA 500


1. The connectivity cable driver is located on the Nemo Outdoor USB flash drive. Browse to folder Nemo Outdoor x.xx\Drivers\Nokia drivers\Nokia 500 and run the Nokia_Suite_webinstaller_All file.

2. When the installation starts, choose your language and click Install.

3. Click I accept.

4. After the Nokia Suite installation is finished, close the installation dialog and connect the connectivity cable to the mobile and the other end to the computer’s USB port. Windows will detect the new hardware automatically and install the drivers.

5. After installation, go to Device Manager. Under Wireless Communication Devices you should see the Nokia xxxx USB Phone Parent item. Under Modems, you should see three Nokia xxxx (USB) items. Leave the Device Manager open as you will find there the COM port numbers needed in the next steps.


Page 59


7. In the Device Manager click on Modems. Select the COM port number assigned to the first/unnumbered Nokia xxx USB item In the Trace Port field in the Device Configuration dialog. Select the COM port number assigned to the second highest Nokia xxx USB item in the Modem Port field.




Page 60

18 NSN USB-LTE 7210 (ALTAIR)

♦ Do not connect the USB connectivity cable to your PC until the driver installation prompts you to do so.

1. First the Connection Manager is installed. The installation file is located on the Nemo Outdoor USB flash drive. Browse the file and double-click the LTE7210_xxxx_EngineeringRelease.exe file (xxxx refers to the version number).

2. First select the Installer language and click OK.

3. Click Next in the Welcome dialog. Click I Agree in the License Agreement dialog.

4. Choose the destination folder and click Next.

5. If at some point you see the Select Components dialog, select Full Installation and click Next.


Page 61

6. Define the Start Menu Folder and click Install.

7. At some point during the Connection Manager installation, the Device Driver Installation Wizard starts up automatically. Click Next in the Welcome dialog.


Page 62

8. The device driver installation is completed and you can now connect the device to your computer. Click Finish.

9. Windows will automatically detect the new hardware and install the required drivers.

10. Return to the Connection Manager installation. When the installation is complete, click Finish.


Page 63

11. The Connection Manager will launch automatically but it is important that it is closed before adding the device to Nemo Outdoor. It is recommended that you rename the .exe file that launches the Connection Manager to prevent the CM from starting. Browse to C:\Program Files \NSN LTE Connection Manager (or for 64-bit Windows C:\Program Files (x86)\NSN LTE Connection Manager) and rename the nsnltecm.exe to nsnltecm.exe_.

12. To avoid performance issues with the modem, the Altair LogCreator standalone functionality needs to be disabled. Browse to folder C:\Program Files\NSN LTE Connection Manager\Tools\ Internals\LogCreator and open file RunLogCreator.bat with Notepad. Modify the following string:

• Original: LogCreator.exe -SA -FN:"50" -E -Y4:"LOG_SOCK_IF" -D4:".\LoggerDB\LTELogDB.txt" -D1:".\LoggerDB\PhyFWLogDB.txt" -Q:"50000"

• Modified: LogCreator.exe -E -Y4:"LOG_SOCK_IF" -D4:".\LoggerDB\LTELogDB.txt" -D1:".\LoggerDB\PhyFWLogDB.txt" -Q:"50000"

13. Go to Device Manager. Under Ports you should see Nokia Siemens Networks LTE Application Interface item.

14. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device dialog, click Phones and select Altair. Click Next.


• Trace port: Select Altair USB

• Modem port: Select the COM port number assigned to the Nokia Siemens Networks LTE Application Interface

16. In the Device Configuration dialog, select <NDIS> and click Apply.

17. If the device connecting fails, check that you have selected the correct COM ports and try again. Also check that the NSN Connection Manager is not running.


Page 64

19 MOTOROLA USBW 25100

1. Run the ClearCM_v1.05.0035.exe file on the Nemo Outdoor USB flash drive.

2. Wait until extraction and installation finishes and until Clear Connection Manager starts up.

3. When CLEAR Connection Manager is running (no device detected), connect the device to a free USB port.

4. The Connection Manager automatically installs the drivers; when done, it will start searching for a network.


Page 65

5. Go to Device Manager in Start | Settings | Control Panel | System | Hardware. Double-click on the Network adapters item. The WiMAX Network Adapter item should be in the list.


7. Select Measurement | Add New Device. In the New Device dialog, click Phones and select the terminal. Click Next.

8. In the Device Manager click on Modems. Select the BECEEM USB in the Trace Port field in the Device Configuration dialog. Leave the Modem Port field empty.



♦ Note that the connection must be activated via the Clear Connection Manager, which also needs to be running during measurements, for the device to work with Nemo Outdoor.


Page 66

20 SAMSUNG GALAXY CORE (SM-G386F)


1. Insert the Nemo Outdoor installation DVD and browse to the driver folder (e.g. Nemo Outdoor\Nemo Outdoor xx\ Drivers\Broadcom\Samsung Galaxy Core SM-G386F). Double-click the Samsung USB Driver for Mobile Phones xxx.exe to run the installation.

2. When the installation is complete, connect the device to the PC.

3. Go to Device Manager. Under Ports you should see the Samsung Mobile USB Serial Port item. Under Modems you should see the Samsung Mobile USB Modem item.

4. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device dialog, click Phones and select the Broadcom item. Click Next.


• Trace port: Select the COM port number assigned to the Samsung Mobile USB Serial Port (in the example above, COM34)

• Modem port: Select the COM port number assigned to the Samsung Mobile USB Modem.


Page 67

6. In the Device Configuration dialog, select SAMSUNG Mobile USB Remote NDIS Network Device as the Packet switched dial-up connection (see page 6). Click Apply.



Page 68

21 SAMSUNG GALAXY S4 (GT-I9505, SGH-I337, SPH-L720, SGH-M919, SCH-R970, SGH-M919N, SGH-I337M), GALAXY S4 ACTIVE (GT-I9295), GALAXY S II (GT-I9210)


♦ Check that the Mobile data setting is disabled from the device. Pull down the menu from the top of the device screen and check that the Mobile data setting is grayed out. Also check that WiFi and Bluetooth are disabled.

1. Insert the Nemo Outdoor USB flash drive and browse to the driver folder (e.g. Nemo Outdoor\Nemo Outdoor xxx\Drivers\Qualcomm\Samsung\Samsung Galaxy S4). Double-click the SAMSUNG_USB_Driver_for_Mobile_Phones_1_5_22_0.exe file to start the installation. Follow the steps in the installation wizard.

2. When the installation is complete, connect the terminal to your PC with the USB cable. Windows will install the device drivers automatically.


Page 69

3. Go to Device Manager. Under Ports, you should see two Samsung Mobile USB Serial Port items.



• Trace port: Select the COM port number assigned to the Samsung Mobile USB Serial Port with the bigger number. If device connecting fails, try the other port.

• Modem port: Select the COM port number assigned to Samsung Mobile USB Modem

• Packet-switched dial-up connection: NDIS

6. Click Apply.



Page 70

22 SAMSUNG GALAXY S II SKYROCKET, GALAXY S II HD LTE (SHV-E120S KOREAN VERSION)


1. Insert the Nemo Outdoor installation DVD and browse to the driver folder. Double-click the driver file (SAMSUNG_USB_Driver_for_Mobile_Phones) to start the installation. Click Next in the Welcome dialog.

2. Select your language and country from the list and click Next.

3. Select the installation location and click Install.

4. The driver files are installed. Wait until the installation is finished and click Exit.

5. Switch on the mobile. Connect the USB cable to the mobile and the other end of the cable to a USB port on your computer. Wait for Windows to detect the device.


Page 71

6. When the installation is complete, check from the Device Manager (Start | Settings | Control Panel | System | Hardware | Device Manager) that the installation was successful. Under Modems you should see the Samsung Mobile USB Modem item and under Ports you should see the Samsung Mobile USB Serial Port item. Leave the Device Manager open as you will find there the COM port numbers needed in the next steps.



• Trace port: Select the COM port number assigned to the Samsung Mobile USB Serial Port with the bigger port number (in the example above, COM53)

• Modem port: Select the COM port number assigned to the Samsung Mobile USB Modem


10. If the device connecting fails, select the Samsung Mobile USB Serial Port with the smaller port number and try again.


Page 72

23 SAMSUNG GALAXY S III (SGH-I747, SGH-T999, SCH-I535, SPH-L710), GALAXY RUGBY, GALAXY S4 MINI (GT-I9195, SPH-L520), GALAXY S4 4G+ (GT-I9506), GALAXY NOTE 3 (SM-N9005, SM-N900T, SM-N9008V, SM-N9007), GALAXY NOTE 3 LITE (SM-N7509V), GALAXY NOTE 4 (SM-N910F, SM-N910G), GALAXY S5 (SM-G900F, SM-G900I, SM-G900P, SM-G900A, SM-G900T, SM-G900W8, SM-G9006V, SM-G900V, SM-G900T1, SM-G900R4, SM-G9009W, SM-G9008V)


♦ If the Samsung Galaxy S III terminal has been used with Nemo Handy, the device needs to restarted or powered off/on before connecting it with Nemo Outdoor.

♦ With Galaxy S4 Mini (GT-I9195), Galaxy S4 4G+ (GT-I9506), and Galaxy Note 3 (SM-N9005, SM-N900T TMOB): Check that the mobile data setting is disabled from the device. Pull down the menu from the top of the device screen and check that the mobile data setting is grayed out. Also check that WiFi and Bluetooth are disabled.

1. Insert the Nemo Outdoor installation DVD and browse to the driver folder (e.g. Nemo Outdoor\Nemo Outdoor xx\Drivers\Qualcomm\Samsung\Samsung Galaxy S III). Double-click the Samsung USB Driver for Mobile Phones 1.5.22.0.exe to run the installation.

2. When the installation is complete, connect the device to the PC.


Page 73

3. Go to Device Manager. Under Ports you should see the Samsung Mobile USB Serial Port item. Under Modems you should see the Samsung Mobile USB Modem item.




• Modem port: Select the COM port number assigned to the Samsung Mobile USB Modem. Note! For Galaxy Note 3 (SM-N9005 variant only), select Not used.




Page 74

♦ To be able to make voice calls, the voice call method must be selected in Nemo Outdoor (Devices view - Voice call method - Trace interface). For Samsung Galaxy S III SGH-T999 and SGH-i747, select Trace interface 2. With S4 variants, leave the field empty.


Page 75

24 SAMSUNG GALAXY S III (GT-I9305), GALAXY II NOTE (GT-N7105)

♦ If the terminal has been used with Nemo Handy, the device needs to restarted or powered off/on before connecting it with Nemo Outdoor.

♦ When the UE is used with Nemo Outdoor, other terminals cannot be used simultaneously in data testing if the NDIS interface is used to activate PS data connection. For example, simultaneous data testing with Huawei LTE modem and Samsung Galaxy S III handset is not possible. It should be noted that the issue does not limit using multiple Galaxy S III terminals for simultaneous data testing or together with non-NDIS terminals, such as, Nokia test terminals.

♦ To be able to make voice calls the “Trace interface 2” call method must be selected in Nemo Outdoor (Devices view - Voice call method - Trace interface 2).

.

♦ Automatic answering to incoming calls can be done only when a headset is connected to the terminal. Use the original headset included in the sales package. Connect the headset to the phone and from the phone menu select: Settings -> Call Answering/ Ending-> Press arrow “<” on the left upper corner to go back to previous menu. Select Settings -> Accessibility -> Call Settings -> Accessory Settings For Call -> Automatic Answering. Automatic answering will operate only with the headset connected.

♦ Auto detection should not be used to add the device. Add the device manually.


Page 76

♦ Check that Enable USB auto tethering option is selected.

♦ USB mode must be RDNIS + DIAG + MODEM. Otherwise handset cannot be used with Nemo Outdoor/ Invex. This is selected automatically when application is installed. Return to main menu.

♦ If data testing is done manually without script files, recording must be started before data protocols can be accessed via Nemo Outdoor. Without recording, the data protocol options in the UI are not available.

♦ The following settings should be activated from the phone for data testing:

• Settings -> More settings -> Mobile networks -> Mobile data enabled-> Enable

• For Samsung Galaxy S III: Settings -> More settings -> Mobile networks -> Network Mode -> AUTO

• For Samsung Galaxy II Note: Settings -> More settings -> Mobile networks -> Network Mode -> Network Mode -> LTE/GSM/WCDMA (Auto mode)

♦ With Samsung Galaxy S III (GT-i9305) and Samsung Galaxy II Note (GT-N7105): The device is always online. This means that attach/detach and PDP context activation/deactivation commands cannot be used via Nemo Outdoor. It is recommended that the access point name (APN) is defined for the phone manually. Otherwise the phone can choose an incorrect APN automatically and this may cause the packet session to fail.


1. Insert the Nemo Outdoor installation DVD and browse to the driver folder (e.g. Nemo Outdoor\Nemo Outdoor xxx\Drivers\Qualcomm\Samsung\Samsung Galaxy S III). Double-click the Kies_x.x.x.exe to start the installation.

2. Select the installation language.

3. Select I accept… in the License Agreement dialog and click Next. Wait for the installation to finish. It may take several minutes.

4. If the Samsung Kies software starts, close the program. If the program suggests a driver update, do not update.

5. When the installation is complete, connect the terminal to your PC with the USB cable. Windows will install the device drivers automatically.

6. Go to Device Manager. Under Ports, you should see the Samsung Mobile USB Serial Port item.


Page 77




• Modem port: Select Not Used.

• Packet-switched dial-up connection: Automatic

9. Click Apply.



Page 78

25 SAMSUNG DROID CHARGE


1. Insert the Nemo Outdoor installation DVD and browse to the driver folder. Double-click the driver file (SAMSUNG_USB_Driver_for_Mobile_Phones) to start the installation. Click Next in the Welcome dialog and follow the instructions in the wizard to finish the installation.

2. When the installation is finished, switch on the mobile. Connect the USB cable to the mobile and the other end of the cable to a USB port on your computer. Wait for Windows to detect the device.

3. Enable USB tethering from the mobile (Menu – Settings - Wireless & networks - Tethering & portable hotspot, select USB tethering). Wait for Windows to finish the driver installation.

4. When the installation is complete, check from the Device Manager (Start | Settings | Control Panel | System | Hardware | Device Manager) that the installation was successful. Under Network adapters you should see the Samsung Android USB Remote NDIS Network Device item and under Ports you should see the Samsung Android USB Diagnostic Serial Port item. Leave the Device Manager open as you will find there the COM port numbers needed in the next steps.


Page 79

5. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device dialog, click Phones and select the Samsung item. Click Next.

6. In the Nemo Outdoor Device Configuration dialog, define the following settings and click Apply:

• Trace port: Select the COM port number assigned to the Samsung Android USB Diagnostic Serial Port (in the example above, COM102)

• Packet switched dial-up connection: Select <Automatic> or the previously made dial-up connection (see page 6).


Page 80

26 LG C676/C680/VX8300/U900/ KU950/KX206/KX256/KF700/ TU550

♦ Do not connect the USB connectivity cable to your PC until the connectivity cable driver installation is complete.

♦ The LG KF700 USB driver conflicts with the LG USB driver for CDMA terminals. If both drivers are installed on the same computer, the terminals are not detected.

1. The connectivity cable driver is located on the Nemo Outdoor USB flash drive. With LG C676, C680, and KX 206, browse to folder D:\Drivers\Qualcomm CDMA drivers, and run the LGUSBModemDriver.exe file. With the LG VX8300 terminal, browse to folder D:\Drivers\Qualcomm US Specific Softwares, and run the LGUSB Driver_Eng__Ver_x.x.exe file (x is the latest driver version). With U900/KU950/KX206/KX256/KF700/TU550, browse to folder D:\Drivers\Qualcomm Specific Softwares\LG USB Driver v.3.35.0.600\Driver and run the Setup.exe file.

2. On the InstallShield Wizard welcome page click Next.

3. If a Software Installation warning appears, click Continue Anyway. You may need to repeat this step two or three times.

4. Click OK in the Information dialog.

5. Next, connect one end of the connectivity cable shipped with the mobile phone to the mobile, and the other end to the computer’s USB port. Windows will detect the new hardware automatically and start the installation.



Page 81


8. Click Continue Anyway or Yes in the Hardware Installation or Digital Signature Not Found dialog if it appears. You may need to repeat steps 5, 6 and 7 several times until the installation process is finished.

9. The USB driver has now been installed. Click Finish.

10. You need to restart your computer for the installation process to take effect. Click Yes in the System Settings Change dialog.

11. After installation, select Start | Settings | Control Panel | Phone and Modem Options, then open the Modem tab.


Page 82

12. Under the Modem item you should see the created LGE CDMA USB Modem and the port attached to it, in this example COM 17.


Page 83

13. Go to Device Manager by selecting Start | Settings | Control panel | System | Hardware. In the Device Manager you should see the LGE CDMA USB Serial Port item. Leave the Device Manager open as you will find there the COM port numbers needed in the next steps.


15. In the Device Manager click on Ports. Select the COM port number assigned to the LGE CDMA USB Serial Port item in the Trace Port field in the Device Configuration dialog. Leave the Modem Port field empty.




Page 84

27 LG VX8350/VX8360

1. Insert the Nemo Outdoor USB flash drive in the USB port. Browse to folder D:\Drivers\Qualcomm Specific Softwares\LGUSBModemDriver.exe.

2. Double-click the .zip file. Click Unzip. This will extract files to a folder in your C drive. Click Close.

3. Switch on the mobile. Connect one end of the USB data cable to the terminal and the other end to an empty USB port on your PC.

4. Windows will automatically detect the new hardware. Select No, not this time in the Found New Hardware Wizard and click Next.

5. Select Install from a list or specific location and click Next.


Page 85

6. Select Include this location in the search and browse to folder D:\Nemo Drivers\LG VX8x00 driver on the Nemo Outdoor USB flash drive. Click Next.

7. The driver files are installed. Steps 2, 3, and 4 are repeated several times until the new hardware is ready to be used.


Page 86

8. When the installation is complete, check from the Device Manager that the installation was successful. Under Modems you should see the LGE CDMA USB Modem, and under Ports you should see the LGE CDMA USB Serial Port item. Leave the Device Manager open as you will find there the COM port numbers needed in the next steps.


10. In the Device Manager click on Ports. Select the COM port number assigned to the LGE CDMA USB Serial Port item in the Trace Port field in the Device Configuration dialog. Leave the Modem Port field empty.




Page 87

28 LG L1000

♦ Do not plug in the data card before installation!

1. Browse to folder D:\Drivers\LG LTE USB Modem on the Nemo Outdoor USB flash drive. Run the LGE Setup_PcUSBDrv20(xxxxxxxx).msi file to start the installation wizard.

2. Click Next in the Welcome window that appears.

3. Click Install in the Ready to Install window.

4. Click Finish in the InstallShield Wizard Completed window.

5. Plug in the data card. Windows will automatically detect the new hardware. Select No, not this time and click Next.

6. Select Install the software automatically and click Next.




Page 88

9. You should see the LGE USB Modem under Modems, and LG Electronics LTE Miniport Driver under Network adapters. Leave the Device Manager open as you will find there the COM port numbers needed in the next steps.


11. In the Device Manager click on Modems. Select the port assigned to LGE USB Modem in the Trace Port field in the Device Configuration dialog. Leave the Modem Port field empty.




Page 89

29 LG P930, G2

♦ Do not plug in the device before installation!

1. Run the LGUnitedMobileDriver_S4981MAN36AP22_ML_WHQL_Ver_3.6.exe file found on the Nemo Outdoor USB flash drive to start the installation wizard.

2. First select the setup language and click Next.

3. Click Next in the Welcome dialog. The driver will be installed. Click OK in the driver installed successfully message.

4. Plug in the device. Enable USB tethering from the mobile (Menu – Settings - Wireless & networks - Tethering & portable hotspot, select USB tethering).

♦ Please note that if the USB connection is disconnected (i.e. device is unplugged), the USB tethering must be re-enabled on the phone in order to use the data connection.

5. Windows will automatically detect the new hardware. Select No, not this time and click Next.

6. Select Install the software automatically and click Next.



Page 90

8. After installation, go to Device Manager. You should see the LGE AndroidNet USB Modem item under Modems and LGE AndroidNet For Diagnostics Port and LGE AndroidNet USB Serial Port items under Ports. Leave the Device Manager open as you will find there the COM port numbers needed in the next steps.



• Trace port: For LG P930: Select the COM port number assigned to the LGE AndroidNet For Diagnostics Port. For LG G2: Select the COM port number assigned to the LGE AndroidNet USB Serial Port.

• Modem port: Select the COM port number assigned to LGE AndroidNet USB Modem.

• Packet-switched dial-up connection: Automatic

♦ When using the device in LTE, do not issue manual packet session commands. If the connection needs to be disconnected, use Radio On/Off commands.

♦ If you are making voice calls, issue an "ATS0=1" AT command to enable the incoming calls. This must be done every time the phone is restarted.


Page 91

30 HUAWEI E3276S-150/861


2. The Telenor Mobile Partner software starts up. Please note that the appearance of the Mobile Partner software varies depending on operator etc. Close the program.


4. You should see the Huawei Mobile Connect – 3G Application Interface item and the Huawei Mobile Connect – Application Interface items under Ports.

5. Install the Hisi UE Agent to default installation folder. The file is located on the Nemo Outdoor USB flash drive. Browse to folder …\Nemo Outdoor x.x\Drivers\HiSilicon\ Hisi UE Agent B211 and run the Hisi UE Agent Balong V700R001C50B211.exe file.

♦ NOTE! After the installation is finished, Hua.exe file must be located under folder C:\Hisi UE Agent\bin\hua.exe.

6. Install Huut- Huawei UE Update Tool 1.3 (Nemo Outdoor x.x\Drivers\HiSilicon\Huut-V1.3.) This is necessary if no diagnostics have been activated yet in UE. Activation can only be performed by Huawei.


Page 92

7. Start Huut- Huawei Update Tool and generate the file. Send the file to Huawei.

8. Update file (key) provided by Huawei with Huut- Update tool. Update file is generated based on IMEI of UE.

9. The device can be added manually. Select Measurement | Add New Device. In the New Device dialog, click Phones and select the HiSilicon item. Click Next.

10. In the Device Manager click on Ports. Select the COM port number assigned to the Huawei Mobile Connect – 3G Application Interface item In the Trace Port field in the Device Configuration dialog. Select the COM port number assigned to the Huawei Mobile Connect – Application Interface item in the Modem Port field.




Page 93

31 HUAWEI ASCEND P2

1. First, install device drivers from folder Nemo Outdoor xxx\Drivers\HiSilicon\Huawei Ascend P2-6011. This will install the Mobile Broadband on your computer. Follow the instructions in the setup wizard to finish the installation.

2. Next install the HiSilicon UE Agent from folder Nemo Outdoor xxx\Drivers\HiSilicon\Hisi UE Agent xxx. Follow the instructions in the setup wizard to finish the installation.

3. Make the following setting on your device:

4. Dial *#*#2846579#*#*. This will open up the Testing menu. Select ProjectMenu.

5. Select Background setting


Page 94

6. Select Usb port setting

7. Select USB mode switch

8. Select Switch to CP modem

♦ Note that USB mode must be switched to CP mode every time the device is rebooted.

9. Connect the device to your computer’s USB port. Windows will detect and install the new hardware automatically.

10. If the Mobile Broadband application starts, close the program.

11. After installation, go to Device Manager.


Page 95

12. You should see the Huawei Mobile Connect – Network Adapter item under Network Adapters and the Huawei Mobile Connect – 3G Application Interface and Huawei Mobile Connect – Application Interface items under Ports.

13. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device dialog, click Phones and select the HiSilicon item. Click Next.


• Trace port: Select the COM port number assigned to Huawei Mobile Connect – 3G Application Interface

• Modem port: Select the COM port number assigned to Huawei Mobile Connect – Application Interface

15. In the Device Configuration dialog, select <NDIS>. Click Apply.



Page 96

32 LG P500H

♦ Do not plug in the device before drivers are installed!

1. Browse to folder Drivers\Qualcomm based devices\LG WCDMA terminals\LG P500H on the Nemo Outdoor USB flash drive.

2. Run the LGAndroidPlatformDriver_WHQL_ML_Ver_1.2_All_Win7.exe file to start the installation wizard. If the Windows Security dialog appears, click Run.

3. After the device driver installation is finished, connect the terminal to the computer with a USB cable. Windows will automatically detect the new hardware and install drivers. Wait until the installation process is finished.

4. After installation, go to Device Manager. You should see the LGE Android Platform USB Modem item under Modems and LGE Android Platform USB Serial Port item under Ports.


6. Select the port assigned to LGE Android Platform USB Serial Port in the Trace Port field in the Device Configuration dialog. Select the port assigned to LGE Android Platform USB Modem in the Modem Port field.

7. In the Device Configuration dialog, select <Automatic> as the Packet switched dial-up connection (see page 6). Click Apply.



Page 97

33 SIERRA WIRELESS AIRCARD 306/307/308/309/310U/ 312U/313U/320U/330U, SIERRA COMPASS 889, SIPTUNE SM215

1. Plug in the USB data card. The data card automatically starts the 3G Watcher driver installation. Siptune SM215 comes with its own driver installation software on a separate USB stick. Follow the instructions in the installation wizard.

2. When the installation is ready, Windows automatically detects the device and installs the driver files.

3. Open the Telstra Turbo Connection Manager main view. Note that the name of the Connection Manager may vary, for example, depending on the operator the device comes equipped with. For example, Sierra Wireless Watcher comes with Sierra 306.


Page 98

4. Select Tools | Options. In the User Options window, select No in the Autolaunch on device insertion or power-up, Do nothing for the On exit field or No in Turn radio off on exit, Never for Check for updates.

5. When these options are selected, you can close the Telstra Turbo Connection Manager/Watcher application, and the device will work in Nemo Outdoor. However, if these options are not selected, the Telstra Turbo Connection Manager/Watcher application needs to run in the background while conducting measurements with the Sierra device in Nemo Outdoor.

♦ Note that the options may vary depending on the device. For example, with Sierra 306, the Tools button is a spanner icon, and instead of On exit field there is Enable airplane mode on exit which needs to be set to No. In addition, the modem name may change depending on the device, for example, to Sierra Wireless HSPA modem.


Page 99

6. When the installation is complete, check from the Device Manager that the installation was successful. Go to Start | Control Panel | System and Security | System | Device Manager. Under Modems you should see a Sierra Wireless AirCard HSDPA Modem item and under Ports pay attention to the Sierra Wireless AT Command Port (UMTS) (COMxx) and Sierra Wireless DM Port (UMTS) (COMxx) items. Under Network Adapters you should see the Sierra Wireless HSPA Network Adapter item. Leave the Device Manager open as you will find there the COM port numbers needed in the next steps.


8. In the Device Manager click on Ports. Select the COM port number assigned to the Sierra Wireless DM Port item in the Trace Port field in the Device Configuration dialog. Click on Modems. Select the COM port number assigned to the Sierra Wireless AT Command Port item in the Modem Port field.




Page 100

34 SIERRA WIRELESS COMPASS 597

1. Insert the USB data card in a free USB slot on your PC.

2. The Sprint SmartView installation setup starts automatically. Double-click on the setup.exe file, and click Setup.

3. Click Next in the Welcome window that appears and follow the instructions in the setup wizard.

4. In the License Agreement window, select I accept the terms in the license agreement, and click

5. After the installation is completed, the software will ask you to restart your computer. Click Yes.

6. Go to Start | Control Panel | System | Hardware | Device Manager. Double-click on Modems to expand it. You should see the Sierra Wireless Compass 597 EVDO Modem item. You should also see the Sierra Wireless Compass 597 DM Port (COMxx) item under Ports. Leave the Device Manager open as you will find there the COM port numbers needed in the next steps.



Page 101

8. In the Device Manager click on Ports. Select the COM port number assigned to the Sierra Wireless Compass 597 DM Port item in the Trace Port field in the Device Configuration dialog. Leave the Modem Port field empty.




Page 102

35 NOVATEL OVATION MC930D/MC990D/MC996D/ MC998D/MC545

♦ Prior to plugging the USB modem in your computer, please refer to the Novatel quick start guide included in the product package for computer system requirements.

1. Insert the (U)SIM card supplied by your service provider in the terminal. Please refer to the quick start guide for more detailed instructions as to how to do this.

2. Insert the Novatel Ovation USB modem into your PC USB port.

3. Windows will automatically install the device driver and detect the new device. In addition, it automatically installs MobiLink Lite which is the device software. Ignore this software, and close it. It should not be on when adding the device to Nemo Outdoor.

4. Next, go to Start | Control Panel | Phone and Modem Options | Modems on your PC. The list should display Novatel Wireless Modem item and the associated COM port number, in this case COM26.


Page 103

5. When the installation is complete, check from the Device Manager that the installation was successful. Under Modems you should see the Novatel Wireless Modem item and under Ports you should see the Novatel Wireless Application Port, Novatel Wireless EAP-SIM Port and Novatel Wireless Status Port items. Under Network adapters you should see the Novatel Wireless Network Adapter item. Leave the Device Manager open as you will find there the COM port numbers needed in the next steps.

6. Exit the MobiLink Lite application before starting Nemo Outdoor.


8. In the Device Manager click on Ports. Select the COM port number assigned to the Novatel Wireless Application Port item in the Trace Port field in the Device Configuration dialog. Click on Modems. Select the COM port number assigned to the Novatel Wireless Modem item in the Modem Port field.

9. In the Device Configuration dialog, select <Automatic> or the previously made dial-up connection as the Packet switched dial-up connection (see page 6). For Novatel Ovation 996D and 998D select <Automatic> in the PS Dial-Up Connection field. Click Apply.



Page 104

36 NOVATEL OVATION MC727/MC760

1. Plug in the Novatel Ovation USB modem data card.

2. Windows will automatically detect the new hardware. Select No, not this time and click Next.

3. Select Install from a list or specific location and click Next.

4. Select Include this location in the search and browse to folder D:\Nemo Drivers\Novatel MC727 usb drivers on the Nemo Outdoor USB flash drive. Click Next.

5. The driver files are installed. Steps 2, 3, and 4 are repeated several times until the new hardware is ready to be used.


Page 105

6. When the installation is complete, check from the Device Manager that the installation was successful. Under Ports you should see the Novatel Wireless Ovation EV-DO Diagnostic Port (COMxx), Novatel Wireless Ovation EV-DO GPS Port (COMxx) and Novatel Wireless Ovation EV-DO Status Port (COMxx )items. Leave the Device Manager open as you will find there the COM port numbers needed in the next steps.


8. In the Device Manager click on Ports. Select the COM port number assigned to the Novatel Wireless Status Port item in the Trace Port field in the Device Configuration dialog. Leave the Modem Port field empty.




Page 106

37 PANTECH UM175

1. Unzip the driver files (PANTECH UM175 USB drivers.zip) on your computer.

2. Plug in the data card.

3. Windows will automatically detect the new hardware.

4. Select Install the software automatically (Recommended), and click Next.

5. Select Include this location in the search and browse for the folder where the driver files are located (e.g., C:\Pantech UM175). Click Next.


Page 107

6. The driver files are installed. Click Finish.

7. Next go to Device Manager. Under Modems you should see the PANTECH UM175 item, and under Ports the PANTECH UM175 Diagnostic Port item.

♦ If you do not see the items mentioned above and instead there are three unknown devices under Others, the driver installation has failed. Right-click each unknown item, select Update Driver Software, and browse to the folder where you unzipped the driver files. After the update, the Pantech items should appear in the Device Manager.

8. Next, set up the dial-up connection manually. Follow instructions on page 7 (for Win 7) then continue from step 9.


Page 108

9. In the Pantech UM175 Modem Properties dialog, Security page, select No encryption allowed in the Data encryption field. Click OK to close the dialog.


11. In the Nemo Outdoor Device Configuration dialog, define the following settings (check the port numbers from the Device Manager) and click Apply:

• Trace port: Select the COM port number assigned to PANTECH UM175 Diagnostic Port

• Modem port: Select the COM port number assigned to PANTECH UM175

• Packet switched dial-up connection: Select the dial-up connection that you configured manually, for example, Pantech UM175



Page 109

38 PANTECH UML290

♦ Do not plug in the device before installation!

1. Browse to folder D:\Drivers\Qualcomm LTE USB Modem on the Nemo Outdoor USB flash drive.

2. Run the VZAM_7.6.3.4_2642j_PantechLTE.exe file to start the installation wizard. If the Windows Security dialog appears, click Run.

3. The device drivers are installed first. After the device drivers are installed, the VZAccess Manager installation is started.

4. Click Next in the Welcome window that appears.

5. Select I accept the terms in the license agreement and click Next.


Page 110

6. Click Next and Next. Select Typical in the Setup Type dialog and click Next and Install. Wait until the installation is ready and click Finish.

7. Plug in the USB modem. Windows will automatically detect the new hardware and install drivers. Wait until the installation process is finished.

8. After installation, go to Device Manager. Select Start | Settings | Control Panel | System, open the Hardware tab and click the Device Manager button. You should see the Pantech UML290 item under Modems and the Pantech UML290 Diagnostic Port item under Ports.


Page 111


10. In the Device Manager click on Modems. Select the port assigned to Pantech UML290 Diagnostic Port in the Trace Port field in the Device Configuration dialog. Select the port assigned to Pantech UML290 in the Modem Port field.

11. In the Device Configuration dialog, select <Automatic> as the Packet switched dial-up connection (see page 6). Click Apply.



Page 112

39 ZTE MF820T/MF820D

1. Connect the device to your computer’s USB port. Windows will detect the new hardware automatically and install the device drivers.

2. The Mobile Broadband application will be installed next. Click Run Setup.exe and follow the instructions on the screen. Select Yes in the User Account Control dialog if it appears.

♦ When the installation is finished, it is important to close the Mobile Broadband application.


• Network adapters: ZTE Mobile Broadband Network Adapter

• Ports: ZTE Mobile Broadband AT Port and ZTE Mobile Broadband Diagnostics Port


5. In the Device Configuration dialog, make the following settings and click Apply:

• Trace Port: Select the port assigned to ZTE Mobile Broadband Diagnostics Port

• Modem Port: Select the port assigned to ZTE Mobile Broadband AT Port

• Packet switched dial-up connection: Select <NDIS> or the previously made dial-up connection (see page 6).



Page 113

40 ZTE MF668A





• Modems: ZTE Proprietary USB Modem

• Network adapters: ZTE Wireless Ethernet Adapter

• Ports: ZTE Diagnostics Interface and ZTE NMEA Device



• Trace Port: Select the port assigned to ZTE Diagnostics Interface

• Modem Port: Select the port assigned to ZTE Proprietary USB Modem




Page 114

41 ZTE MF683

1. Start the driver installation by selecting the correct installation file based on your operating system (..\Drivers\Qualcomm\ZTE\ZTE MF683\USBDriverInstaller_x64.exe or USBDriverInstaller_x86.exe). The installation will run on the background.



• Modems: T-Mobile HSPA+ Modem

• Network adapters: T-Mobile Wireless Ethernet Adapter

• Ports: T-Mobile Diagnostics Port.



• Trace Port: Select the port assigned to T-Mobile Diagnostics Port

• Modem Port: Select the port assigned to T-Mobile HSPA+ Modem

• Packet switched dial-up connection: Select <Automatic> or the previously made dial-up connection (see page 6).



Page 115

42 ZTE MF880





• Modems: ZTE Mobile Broadband Modem

• Network adapters: ZTE Mobile Broadband Network Adapter

• Ports: ZTE Mobile Broadband Diagnostics Port



• Trace Port: Select the port assigned to ZTE Mobile Broadband Diagnostics Port

• Modem Port: Select the port assigned to ZTE Mobile Broadband Modem




Page 116

43 ZTE TU25

♦ Make sure that the device is NOT connected to your computer.

1. The installer executable is named ZTE_Common_API.msi, and it can be found on the USB flash drive. Click Run to run the installer.

2. Click Next in the Welcome dialog.

3. Click Next in the Destination Folder dialog.

4. Click Install.

5. Click Continue Anyway.

6. Finally click Finish. The driver is now installed. Next, plug in the USB device.

7. Click Continue Anyway until the prompt no longer appears.


Page 117

8. Next, browse to Start | Control Panel | System | Hardware and click on the Device Manager button. Under Network adapters you should see the ZTE WiMAX BCM1000 item.

9. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device dialog, click Phones and select the Beceem BCS200 (524) item. Click Next.

10. In the Device Manager click on Modems. Select the BECEEM USB in the Trace Port field in the Device Configuration dialog. Leave the Modem Port field empty.




Page 118

44 SONY ERICSSON XPERIA ARC S

♦ Please note that currently the Sony Ericsson Xperia Arc S driver can be installed on 32-bit Windows 7 only.

1. Before connecting the Sony Ericsson Xperia Arc S to a computer, make the following settings on the device. Go to Settings | Applications | Development. Deselect USB debugging.

2. Connect the device to your computer’s USB port. Windows will detect the new hardware automatically.

3. Open the Device Manager. Under Other devices you will see two SEMC HSUSB Device items. If an MTP device appears instead of SEMC HSUSB, expand the Universal Serial Bus controllers item, and delete the USB Mass Storage Device item. Then disconnect and reconnect the data cable from the mobile. The device should now be detected correctly.

4. Right-click on the first item and select Update Driver Software.


Page 119

5. Select Browse my computer for driver software.

6. Select Let me pick from a list of device drivers on my computer.


Page 120


8. Select Have Disk.


Page 121

9. Browse to the folder on the Nemo Outdoor USB flash drive where the Sony Ericsson drivers are and click Open.

10. Click OK.


Page 122

11. Select the Sony Ericsson sa0102 Device Modem item and click Next.

12. Click Yes in the Update Driver Warning message.

13. Click Close when the installation is finished.


Page 123

14. Return to the Device Manager. The Sony Ericsson sa0102 Device Modem item should appear under Modems and there should be one SEMC HSUSB Device item under Other devices.

15. Again, right-click on the SEMC HSUSB Device item and select Update Driver Software. Repeat steps 3-9.


Page 124

16. Select the Sony Ericsson HS-USB Android Diag sa0102 item and click Next.

17. Click Yes in the Update Driver Warning message and click Close when the installation is finished.

18. Return to the Device Manager. The Sony Ericsson HS-USB Android Diag sa0102 item should appear under Ports.


Page 125


20. Select the port assigned to Sony Ericsson HS-USB Android Diag sa0102 in the Trace Port field in the Device Configuration dialog. Select the port assigned to Sony Ericsson sa0102 Device Modem in the Modem Port field.




Page 126

45 ONDA MT689DC


2. Select your language and destination folder. By clicking Next, you also accept the license agreement.

3. When the installation is finished, unplug the device from the USB port and restart the computer.

4. Plug the device back to the USB port. Close the AutoPay dialog.

5. If the Chiavetta Internet MT689DC software starts up, close the program.



Page 127

7. You should see the ONDA Proprietary HS-USB Modem item under Modems and the ONDA HS-USB Diagnostics Interface item under Ports.


9. In the Device Configuration dialog, select the COM port number assigned to ONDA HS-USB Diagnostics Interface item in the Trace Port field. Select the COM port number assigned to the ONDA Proprietary HS-USB Modem item in the Modem Port field.

10. In the Device Configuration dialog, select <Automatic> as the Packet switched dial-up connection. Click Apply.



Page 128

46 APPLICATION TESTER

These dial-up networking setup guidelines apply to any commercial terminal, i.e. a terminal not provided by Anite Finland Ltd, that is used for application testing.

1. First you need to install the connectivity cable driver. The USB connectivity cable driver and an applicable USB connectivity cable for it will be included in your mobile phone package. Note! Do not connect the USB connectivity cable to your PC until the driver installation is complete! Consult the terminal user manual for instructions on how to install the connectivity cable driver.

2. After installing the connectivity cable driver, go to Start | Settings | Control Panel | Phone and Modem Options | Modems and check the Modem port number assigned to the terminal. This port number will be the same as the Modem port in Nemo Outdoor.

3. Next you need to create a dial-up connection to the Internet for the modem port mentioned above. A dial-up networking installation is required before data transfers can be made. Go to Start | Settings | Control Panel | Network Connections. Check to see if the dial-up connection for your phone was automatically installed with the USB connectivity driver installation. If not, create a new dial-up connection from File | New Connection. The dial-up connection you find in the Network Connections window is the same as the Packet switched dial-up connection in Nemo Outdoor.

4. When the USB connectivity driver and dial-up networking installations are complete, go to Nemo Outdoor and select Measurement | Add New Device | Phone | Application Tester. In the Device Configuration dialog select the applicable modem port. The Trace port field is grayed out. In the Packet switched dial-up connection field, select the dial-up connection created earlier. Click Apply. If the status field does not say Device is working properly, check to see that you have selected the right port number and try again.

5. You can also check the earlier chapters in this document for possible similarities to the installation procedures of your terminal.


Page 129

47 TECHNICAL SUPPORT

If you have questions on or beyond this documentation about Nemo tools, please contact our technical support service through Nemo Support Portal at http://nemosupport.anite.com, call us (local phone numbers can be found in chapter Phone and Email Support) or send us an email at [email protected]. Note that for full support you need to have the Maintenance Agreement.

47.1 User Club

Nemo User Club offers several new ways to benefit from Nemo products. You can find it from http://nemouserclub.anite.com.

Access to the Nemo User Club is restricted to customers with SW maintenance and Technical Support agreements or partner agreements. If you are an existing Anite Network Testing customer with SW maintenance and Technical Support agreements, but you are without access to the User Club, please complete an on-line registration form.

After submitting the requested information, you will receive a personal access key and password by email in a few days time.

Once you are registered with our User Club, you will automatically receive e-mails informing you each time a new version of software for your Nemo Product is released. It is fast, easy, and it is available to you seven days a week, 24 hours a day.

47.2 Nemo Support Portal

Nemo Support Portal is a web interface for technical support, product-related questions, and RMA requests. It offers a fast and convenient way to reach our technical support team and submit repair, warranty repair, and calibration requests. Customers can open a support ticket, follow the status of existing tickets, and request technical support 24/7/365. Furthermore the Nemo Support Portal includes a Knowledge Base for the most frequent and latest topics on Nemo Products. Submitting a ticket via Nemo Support Portal ensures that our technical specialists have all the necessary information available to solve your support case, resulting in faster response times.

Please go to http://nemosupport.anite.com to access the portal and click “Request access” to obtain a password to the system.

47.3 Phone and Email Support

During the warranty period, the phone support related to potential software errors is free of additional charge. Registered users with a valid Maintenance Agreement are entitled to full support. Nemo Support Portal is the preferred channel for technical support requests, but you can also send us an email. When emailing, please let us know the number of your Software Maintenance and Support Agreement.

http://nemosupport.anite.com/

mailto:[email protected]

http://nemouserclub.anite.com/

http://nemosupport.anite.com/


Page 130

Please contact us at the following locations:

Global

Mobile +358 50 395 7800

Americas

Mobile +1 469 951 9105

+1 469 774 4608 (En español e português)

APAC

Tel. +65 9746 2431

P.R. China

Tel. +86 10 6567 8528

India

Tel. +91 982 0016372

Middle East

Tel. +86 10 6567 8528

P.R. China

Tel. +97 155 620 4132