19
Static Equilibrium and Elasticity Topic 12 (cont.)

14 static equilibrium and elasticity

Embed Size (px)

Citation preview

Page 1: 14 static equilibrium and elasticity

Static Equilibrium and Elasticity

Topic 12 (cont.)

Page 2: 14 static equilibrium and elasticity

Lecture Outline12.4 Hooke’s Law12.5 Young Modulus12.6 Stress and

Strain12.7 Fracture

Page 3: 14 static equilibrium and elasticity

12.4 Hooke’s LawAn object exerted by force – pulling force – the length will changeIf the amount of elongation is small compare to the length of the object initial length, Hooke’s Law state that: The change in length is proportional to the applied force.

Page 4: 14 static equilibrium and elasticity

F – pulling force Δl – change in length

k – proportionality constant

First noted by Robert Hooke (1635-1703)

Valid for almost any solid material

But applicable for only to a certain point – force is not to strong

Up to a point – Hooke’s Law is not valid

Page 5: 14 static equilibrium and elasticity

This proportionality, holds until the force reaches the proportional limit.

Beyond that, the object will still return to its original shape up to the elastic limit.

Beyond the elastic limit, the material is permanently deformed

More force is apply it breaks at the breaking point.

Ultimate Strength – Maximum force the object can sustain

Page 6: 14 static equilibrium and elasticity

12.5 Young ModulusThe change in length of a stretched object depends not only on the applied force, but also on its length, cross-sectional area and the material from which it is made.The elongation of an object is proportional to the original length and inversely proportional to the cross-section area of the object

E – Elastic modulus/Young Modulus

Page 7: 14 static equilibrium and elasticity
Page 8: 14 static equilibrium and elasticity

Example 12-7: Tension in piano wire.

A 1.60-m-long steel piano wire has a diameter of 0.20 cm. How great is the tension in the wire if it stretches 0.25 cm when tightened?

(E = 2.0 × 1011 N/m2)

Page 9: 14 static equilibrium and elasticity

12.6 Stress and Strain

Stress is defined as the force per unit area.

[unit: N/m2]

Strain is defined as the ratio of the change in length to the original length. (how much an object is deform)

Therefore, the elastic modulus is equal to the stress divided by the strain:

Page 10: 14 static equilibrium and elasticity

Tension/tensile stress

In tensile stress, forces tend to stretch the object.

Three type of stress:

Page 11: 14 static equilibrium and elasticity

Compression stress

Compression – force act inwardly on the object.

Page 12: 14 static equilibrium and elasticity

Compressional stress is exactly the opposite of tensional stress. These columns are under compression.

Page 13: 14 static equilibrium and elasticity

Sheer stress

Equal and opposite force acted on the object – across its opposite faces

G – Sheer Modulus

Page 14: 14 static equilibrium and elasticity

The shear strain, where G is the shear modulus:

Page 15: 14 static equilibrium and elasticity

If an object is subjected to inward forces on all sides, its volume changes depending on its bulk modulus. This is the only deformation that applies to fluids.

or

Page 16: 14 static equilibrium and elasticity

Example: Squeezing a Brass SphereA solid brass sphere is initially surrounded by air, and the air pressure exerted on it is 1.0 × 105 N/m2. The sphere is lowered into the ocean to depth where the pressure is 2.0 × 107 N/m2. The volume of the sphere in air is 0.50 m3. By how much does this volume change once the sphere is submerged? (Bulk Modulus for brass = 80 × 109 N/m2)

Page 17: 14 static equilibrium and elasticity

If the stress on an object is too great, the object will fracture. The ultimate strengths of materials under tensile stress, compressional stress, and shear stress have been measured.

When designing a structure, it is a good idea to keep anticipated stresses less than 1/3 to 1/10 of the ultimate strength.

12.7 Fracture

Page 18: 14 static equilibrium and elasticity
Page 19: 14 static equilibrium and elasticity

Example 12-8: Breaking the piano wire.

A steel piano wire is 1.60 m long with a diameter of 0.20 cm. Approximately what tension force would break it?

(Tensile strength of steel = 500 × 106 N/m2)