Algae Lab Grade Photobioreactor Guide

This new Algae PBR CD set or Book gives a step-by-step instructions on making an algae test photo bioreactor. This information can be used in any application that calls for testing and/or growing algae, to determine maximum growth rates, best nutrients, etc., such as...

Making algae biodiesel, Animal feed, Organic fertilizer, Cosmetics, Health food supplements and many more.

Because this is more involved than can be explained clearly in a single instruction, I'll have to include multiple parts.

It includes a complete parts list, color diagrams, step-by-step instructions, and full color photos. Get a Full Copy for your Library Today: www.AlgaeBiodieselInfo.com

How To Make an Algae Test Photo Bioreactor…Introwww.AlgaeBiodieselInfo.com

www.AlgaeBiodieselInfo.com

http://www.algaebiodieselinfo.com/


step 1-Building the Base

Materials needed: 17 Plant (saucer) caddy (Home improvement store $17.99) (10) 2 PVC "repair" couplings (Home improvement store $1.65 a piece) (2) 28 x 48 x plexi-glass (Home improvement store $6.97 a piece) (2) 2x4 steel brackets (Home improvement store $0.96 a piece) Aquarium sealant (Home improvement store $3.98) Wood screws and washers Tools Needed: Power drill Jig saw Hack saw Straight edge Marker Vice


step 2-Base Assembly

Take out the plastic insert in the plant caddy and set aside. Place the plant caddy upside down on the Plexi-glass panel



Draw a circle on the INSIDE edge of the plant caddy.



Take the jigsaw and cut along the circumference of the circle. You may want to cut along the inside of your pencil mark to make sure your wood panel fits into the plant caddy easily.



Place the plexiglass on top of 2"x4"s making sure the posts are squarely up and down. With a plumb bob, find the center of the cell receivers on the caddy below. Place on a dot on the plexiglass for the center of each cell


step 7-Upright and Castle Assembly

Place the 1.5inch PVC coupler on top of the plexiglass with the dot in the center and outline the outside of each coupler.www.AlgaeBiodieselInfo.com




Place the plexiglas on the drill press and CAREFULLY drill out each marked hole with an 1 3/4" inch drill bit.



Measure 9inches from the edge and mark another across the middle. This should give you the exact center. With the 2" inch drill bit, drill a hole in the exact center of the plexiglass. Clean the burrs off with a rounded file.



Turn the plexiglass upside down on the work bench and using the PVC Cement, place a bead of glue around the edge of the 1.5" couplers and mount on the plexiglass. Repeat for all 10 holes. Allow the Cement to dry for a couple of hours.



Flip the plexiglass over so that the couplers are facing down. Mark 3 evenly spaced dots on the plexiglass, directly where the 2"x4" is centered. Drill pilot holes in the plexiglass, the secure to the 2"x4"s.



The completed castle and uprights should look like this:

Materials needed: (1) 2"x4"x 8' stud (10) 1.5"PVC "repair" couplers (1) 28" x 48" x plexiglass (2) 2"x4" steel brackets Aquarium and/or marine silicone Wood screws and washers Tools Needed: Power drill (or drill press) 2" inch hole drill 1.5" inch drill bit Carpenter's square Plumb bob Jig saw Straight edge Marker www.AlgaeBiodieselInfo.com

step 13-Order Your Copy Today!www.AlgaeBiodieselInfo.com


http://algaebiodieselinfo.com/index.html

Self Improvement

Algae Lab Grade Photobioreactor Guide