Upload
jms-express-plumbing
View
210
Download
0
Embed Size (px)
DESCRIPTION
The every person whenever a leakage of pipe occurs in their houses or commercial building it create more problem so they want to solve it as soon as possible Whenever it occurs you should keep a cool head, and stop most of them until a plumbing profession will come to your house to do the pipe repair work.
Citation preview
JMS EXPRESS PLUMBING
How to Fix a Damaged Landscape sprinkler Line
Decrease water pressure, spouts, and dry
grass areas are some of the things you need
to be paying attention to when it comes to
malfunctioning sprinklers. If you determine
your sprinklers are not working properly here
is a guide on how you can try to fix them up.
Isolate where the leak is.
This might need a little bit of investigating; Very often you
have separated water lines, one for the garden and one for
the house. Figure out which one supplies the sprinklers
you want to fix and shut it off. Buy the same grade, size
and if possible brand of pipe as the one already installed.
Pipes have makings on the sides with all this information,
write it down and ask for assistance at the hardware store
to make sure you get the right one.
JMS EXPRESS PLUMBING
Dig a big enough area to comfort work
with the piping. This is important,
because you need to have enough space
to properly work with the pipes and
fixtures.
JMS EXPRESS PLUMBING
JMS EXPRESS PLUMBING
Remove as much water and mud as possible
from your working space. Cut out the segment
of the pipe line you want to replace smoothen
the edges and keep dirt out of the inside of the
pipe. You can use a paper towel to cover the
pipe’s endings and prevent dirt from going
inside the pipes.
Remove as much water and mud as possible from your working space. Cut out the segment of the pipe line you want to replace smoothen the edges and keep dirt out of the inside of the
pipe. You can use a paper towel to cover the pipe’s endings and prevent dirt from
going inside the pipes.
JMS EXPRESS PLUMBING
Using green federal government and the sweep that comes with it, main the
outside of both of the staying landscape sprinkler tube stops by artwork a 1-2
inches large remove around the outside of each tube end beginning at the
lip/edge.
JMS EXPRESS PLUMBING
Connect a coupler to each tube end by implementing a cover of stick on outside of the
tube end and also to the inside of a coupler. Operating easily, strongly fall the coupler onto
the tube side using a turning movement, forcing hard until the tube visits the lip in the middle of
the coupler. Carry the coupler in place with stress for 15-20 a few moments. The clear stick
cures in roughly 10 a few moments and the pink stick in roughly 20 a few moments so you must work easily. Do it again for the other tube end.
JMS EXPRESS PLUMBING
Cut a portion of repair pipe to fit the length of the cut you made in the
sprinkler line, minus approximately 1/2" or more for each straight coupler used (the coupler adds approximately 1/2 inch to the length of the finished
pipe)
JMS EXPRESS PLUMBING
To decide the length of the repair pipe, measure from the middle of one straight coupler to the other
using a tape measure. If you don't have a tape measure, lay a piece of
pipe down into the trench and measure it by eye, marking with a
pen or pencil for your cut.
JMS EXPRESS PLUMBING
Fit the cut piece into the couplers dry, to be sure that the fit is
accurate and that the resulting pipe is not bent, from the
replacement piece being too long.
JMS EXPRESS PLUMBING
Disassemble and make any essential adjustments, until the resulting fit is perfect.
JMS EXPRESS PLUMBING
Prime both ends of your cut piece, wait 5 seconds, then apply a light layer of glue to one end of the replacement piece and inside one of the
straight couplers.
JMS EXPRESS PLUMBING
Twist pipe hard into coupler until you feel it stop. Wait at least a full minute for that to dry then
apply glue to the remaining pipe-end and coupler. With your final fitting, you may have to pull hard on the sprinkler-line pipe, either to the side or up, in order to get the replacement pipe
to slip into the coupler. Don't worry, PVC is strong. Allow all fittings and joints to dry
completely for 3-5 minutes before rotating water back on in that line.
JMS EXPRESS PLUMBING
On the other hand, use a "repair" combining which does not have the
within middle ridge; generally an over-sized area of tube
JMS EXPRESS PLUMBING
With a repair coupling you can slide it all the way on the new pipe section,
prime & glue the other pipe, and slide the repair
coupling onto the old pipe.
JMS EXPRESS PLUMBING
Alternatively, you can cut a coupling piece in half, lengthwise
JMS EXPRESS PLUMBING
Smash down the inside middle side if it's a straight combining. Then primary and stick one or both sections, based on duration of break, and primary and stick the old tube
around the break, and use the half-piece(s) over the break. Closes the break and it's
quicker than reducing out the damaged area of tube, especially if the damaged tube is
close to another tube or if it's simply hard to dig out enough.
JMS EXPRESS PLUMBING
Watch the area of your repair for a few minutes before you cover
your whole back up.
JMS EXPRESS PLUMBING
7423 Densmore Ave,Van Nuys,
CA - 91406,USA.
Toll free number: 888-881-9898www.jmsexpressplumbing.com
Contact