Upload
zlatan-ahmadovic
View
73
Download
2
Embed Size (px)
Citation preview
Planar waveguides
Planar waveguides are an important subclass of
waveguides (transmission lines)
Planar waveguides can be used in integrated
circuits to connect the various microwave circuit
elements
Examples are shown in the next three slides
1Falah Mohammed
Applications of planar
waveguidesAlso planar transmission lines can be used to
feed microwave energy from a microwave
generator to an antenna as shown
2Falah Mohammed
Applications of planar
waveguidesPlanar waveguides can be used to
interconnect the various parts of a
microwave amplifiers
3Falah Mohammed
Applications of planar
waveguidesPlanar wave guides also can be used to
design filters and phase shifters
4Falah Mohammed
Filter Phase shifter
Types of planar wave guides
There are many types of planar waveguides
available. Examples are
Strip line
Microstrip line
Coplanar waveguide
Slotted lines
These waveguides support TEM, TE and TM
wave propagations
However only TEM will be considered
5Falah Mohammed
Planar waveguide design
parametersWhen designning a given microwave circuit, it is
desired to know the characteristic impedance,
dispersion curves, phase velocity, phase delay,
capacitance, inductance and the attenuation per unit
length of the waveguide
Computing these parameters can be performed by
solving the Helmholtz equation
However, the computation can be greatly simplified
by the use of commercial microwave design tools
such as CST, AWR microwave office, Agilent ADS,
and HFSS
6Falah Mohammed
Strip-line
The strip line is composed from a thin conducting
strip of width 𝑊 centered between two conducting
ground planes of separation 𝑏
The region between the conducting planes is filled
with a dielectric material whose relative permitivity
is 𝜖𝑟 as shown
7Falah Mohammed
Strip line
The strip line can be considered as a planar
coaxial cable
Exact solution for the electric field can be
obtained by a method known as conformal
mapping
However this avoided in practice and an
empirical formulas can be used to design the
strip line for specific characteristic impedance
𝑍0, phase velocity 𝑣𝑝, propagation constant 𝛽
8Falah Mohammed
Formulas for Propagation Constant,
Characteristic Impedance
The phase velocity can be given by
𝑣𝑝 =1
𝜇𝜖=
𝑐
𝜖𝑟
The propagation constant is given by
𝛽 =𝜔
𝑣𝑝= 𝜔 𝜇0𝜖0𝜖𝑟 = 𝜖𝑟𝑘0
The characteristic impedance can be approximated by
𝑍0 =30𝜋
𝜖𝑟
𝑏
𝑊𝑒 + 0.441𝑏
Where 𝑊𝑒 is the effective width of the center conductor
which is approximated by
9Falah Mohammed
Strip line width for specific 𝑍0
The strip line width that can be used to design a
strip line with a specific characteristic impedance
can be determined from the following equation
𝑥 =30𝜋
𝜖𝑟𝑍0− 0.441
10Falah Mohammed
Attenuation due to conductor
loss
11Falah Mohammed
Example
Find the width for a 50 Ω copper stripline
conductor with 𝑏 = 0.32 𝑐𝑚 and 𝜖𝑟 = 2.2. If the
dielectric loss tangent is 𝑡𝑎𝑛𝛿 = 0.001 and the
operating frequency is 10 GHz, calculate the
attenuation in 𝑑𝐵/𝜆 . Assume a conductor
thickness of 𝑡 = 0.01 mm
12Falah Mohammed
Solution
To find the strip line width we can rely on the
equations in slide 10
𝜖𝑟𝑍0 = 2.2 50 = 74.2 < 120
Therefore
𝑥 =30𝜋
𝜖𝑟− 0.441 = 0.83
We can use the equation𝑊
𝑏= 𝑥 ⇒ 𝑊 = 𝑏𝑥 = 0.32 × 0.83 = 0.266 𝑐𝑚
13Falah Mohammed
Solution
The total attenuation is the attenuation due to
the conductor loss plus the attenuation due to
dielectric material, therefore
𝛼 = 𝛼𝑐 + 𝛼𝑑
𝛼𝑑 =𝑘𝑡𝑎𝑛𝛿
2But
𝑘 = 𝜔 𝜇𝜖 =2𝜋𝑓 𝜖𝑟
𝑐= 310.6
14Falah Mohammed
Solution
Now 𝛼𝑑 =310.6×0.001
2= 0.155 𝑁𝑝/𝑚
The conductor loss can be determined from
The surface resistance for the copper is
𝑅𝑠𝜔𝜇
2𝜎= 0.026 Ω 𝑎𝑡 10 𝐺𝐻𝑧
15Falah Mohammed
Solution
𝛼𝑐 = 2.6 ×10−3𝑅𝑠𝜖𝑟𝑍0𝐴
30𝜋(𝑏 − 𝑡)= 0.122 𝑁𝑝/𝑚
The total attenuation is
𝛼 = 𝛼𝑑 + 𝛼𝑐 = 0.277𝑁𝑝
𝑚𝛼 𝑑𝐵 = 20 log10 𝑒𝛼 = 2.41 𝑑𝐵/𝑚
The wavelength at 10 𝐺𝐻𝑧 is
𝜆 =𝑐
𝜖𝑟𝑓= 2.02 𝑐𝑚
The attenuation in terms of wavelength is
𝛼 𝑑𝐵 = 2.41 × 0.0202 = 0.049 𝑑𝐵/𝜆
16Falah Mohammed
Microstrip line
The microstrip line is one of the most popular
type of transmission lines
The microstrip line is composed from a signal
conductor of width 𝑊 and ground plane
separated by a dielectric material as shown
17Falah Mohammed
Phase velocity, propagation
constant The phase velocity on microstrip line is given by
𝑣𝑝 =𝑐
𝜖𝑒
The propagation constant is given by
𝛽 = 𝜔 𝜇0𝜖0 𝜖𝑒 = 𝑘0 𝜖𝑒
Where 𝜖𝑒 is the effective dielectric constant 1 <𝜖𝑒 < 𝜖𝑟
18Falah Mohammed
Effective dielectric constant 𝜖𝑒
The effective dielectric constant can be
approximated by
𝜖𝑒 =𝜖𝑟 + 1
2+𝜖𝑟 − 1
2
1
1 + 12𝑑/𝑊
19Falah Mohammed
Characteristic impedance
analysis formulaIf the dimensions of the microstrip are known, then
the characteristic impedance can be determined
from
20Falah Mohammed
Characteristic impedance
Synthesis formulaIf the microstrip is designed to have a specific
characteristic impedance, then the ratio of its width
𝑊 to the dielectric thickness 𝑑 can be determined
form
21Falah Mohammed
Microstrip attenuation
The attenuations for quasi TEM microstrip are
determined from the following two equations
22Falah Mohammed
Example microstrip design
Design a microstrip line on a 0.5 mm alumina
substrate ( 𝜖𝑟 = 9.9, 𝑡𝑎𝑛 𝛿 = 0.001 ) for a 50 Ωcharacteristic impedance.
Find the length of this line required to produce a
phase delay of 270° at 10 GHz, and compute the
total loss on this line, assuming copper
conductors.
23Falah Mohammed
Solution If we assume that
𝑊
𝑑< 2, the width 𝑊 can be
determined from
𝑊
𝑑=
8𝑒𝐴
𝑒2𝐴 − 2
𝐴 =𝑍060
𝜖𝑟 + 1
2+𝜖𝑟 − 1
𝜖𝑟 − 10.23 +
0.11
𝜖𝑟= 2.142
𝑊/𝑑 = 0.9654 which is less than 2
The required width of microstrip line is 𝑊 =0.9654𝑑 = 0.483 𝑚𝑚
24Falah Mohammed
Solution
The length of the line that can produce a phase
shift of 𝜙 = 270° can be determined from the
electrical length
𝜖𝑒 = 6.665𝜙 = 𝛽𝑙 = 𝜖𝑒𝑘0𝑙 = 270
𝑘0 =2𝜋𝑓
𝑐= 209.4 𝑚−1
𝑙 =270
𝜋180
𝜖𝑒𝑘0= 8.72 𝑚𝑚
25Falah Mohammed
Solution
By solving for 𝛼𝑑 and 𝛼𝑐 , we have a total
attenuation of 𝛼 = 𝛼𝑑 + 𝛼𝑐 = 0.022 + 0.094 =0.116 𝑑𝐵𝑚/𝑐𝑚
The attenuation within the length of the phase
shifter is given by
𝑎𝑡𝑡𝑒𝑛𝑢𝑎𝑡𝑖𝑜𝑛 = 𝛼𝑑𝐵𝑐𝑚 × 𝑙𝑒𝑛𝑔𝑡ℎ 𝑜𝑓 𝑡ℎ𝑒 𝑙𝑖𝑛𝑒𝑎𝑡𝑡𝑒𝑛𝑢𝑎𝑡𝑖𝑜𝑛 = 0.116 × 0.872 = 0.101 𝑑𝐵
26Falah Mohammed
Coplanar waveguide
The coplanar waveguide is composed
from a central conductor with two ground
planes as shown below
27Falah Mohammed
Coplanar waveguide
The impedance of the coplanar waveguide can
be determined the width of the central conductor
𝑊 and the spacing from the ground planes 𝑆
28Falah Mohammed
Commercial software
The dimensions of planar wave guide can
be adjusted for specific 𝑍0, 𝑣𝑝, 𝛽, 𝑎𝑛𝑑 𝜙 by
using CAD tool such on line tools or
Linecalc in ADS
29Falah Mohammed
Linecalc
30Falah Mohammed
You can find the line calculator program
under tools, then LineCalc
Starting the line calculatorIf you press the start LineCalc item, you may obtain a
window as shown below
31Falah Mohammed
Entering the dielectric parameters
You can enter the
dielectric (substrate)
parameters in the
following section of
the LineCalc window
32Falah Mohammed
Computing
𝑍0, 𝑝ℎ𝑎𝑠𝑒 𝑠ℎ𝑖𝑓𝑡 𝜙 , 𝜖𝑒 (Analysis)Enter the width and length of the transmission line and
click on the analyze window, the LineCalc program will
compute 𝑍0, 𝜙, 𝜖𝑒 as illustrated by
33Falah Mohammed
Computing the 𝑊 and 𝐿 for a
specific 𝑍0 and 𝜙 (Synthesis)Enter the value of the desired 𝑍0 and the phase shift in
the section provided, press synthesize, the program will
compute the width and length of the transmission line
34Falah Mohammed
Comparison of Common Transmission
Lines and Waveguides
35Falah Mohammed
36Falah Mohammed
Microwave Frequency Bands (taken from wikipedia)
Letter Designation Frequency range
L band 1 to 2 GHz
S band 2 to 4 GHz
C band 4 to 8 GHz
X band 8 to 12 GHz
Ku band 12 to 18 GHz
K band 18 to 26.5 GHz
Ka band 26.5 to 40 GHz
Q band 33 to 50 GHz
U band 40 to 60 GHz
V band 50 to 75 GHz
E band 60 to 90 GHz
W band 75 to 110 GHz
F band 90 to 140 GHz
D band 110 to 170 GHz