14
A MEMS Thermal Biosensor for Metabolic Monitoring Applications

MEMS Thermal Biosensor

Embed Size (px)

Citation preview

Page 1: MEMS Thermal Biosensor

A MEMS Thermal Biosensor for Metabolic

Monitoring Applications

Page 2: MEMS Thermal Biosensor

What is a Biosensor?

“Biosensor” is short for “Biological Sensor”. An Analytical device which converts a Biological response into an

Electrical Signal. A Biosensor typically consists of a Bio-recognition component,

Biotransducer component, and electronic system which include a signal amplifier, processor, and display.

Page 3: MEMS Thermal Biosensor

Components of a Biosensor

Page 4: MEMS Thermal Biosensor

Thermal Biosensor

THERMAL biosensors measure thermal energy released or absorbed in biochemical reactions.

Thermal activities exist ubiquitously in Biological Processes, and hence widely applicable.

Requiring no labeling of reactants, thermal bio sensing is a universally useful method, allowing direct interrogations of elementary processes in biochemistry without sophisticated cascades of reaction steps.

Page 5: MEMS Thermal Biosensor

Thermal Biosensor

MEMS thermal sensors are often based on temperature detection.

I. Thermistors Rely on changes in their electric resistance with temperature. Allow measurement of absolute temperatures. Limited in sensitivity

II. Thermopile Set of Thermocouple Junctions connected in series. Allows measurement of differences in temperature between two Junctions. Offers excellent common-mode noise cancellation and zero offset, and therefore can be highly

Sensitive.

Page 6: MEMS Thermal Biosensor

Advantages of MEMS Thermal Biosensor

Improved Thermal Isolation. Reduced Thermal Mass and Sample Volume. Offer improved Sensitivity and Linear Range. Reduced Power Consumption. Shortened Measurement Times. Allows batch fabrication and integration of miniaturized devices at

low cost Enable High-Throughput Operation

Page 7: MEMS Thermal Biosensor

Design

Device consists of a thermal sensor chip integrated with a microfluidic system featuring two identical chambers.

An analyte sample solution and a reference buffer solution are respectively loaded into the chambers.

The device can be used in Two modes: Flow-Injection mode and Flow-Through mode. An important feature of the microfluidic system is that the chambers are each based on a

freestanding polymer diaphragm. The temperature difference induces a voltage in the thermopile, which is the device’s direct output

Page 8: MEMS Thermal Biosensor
Page 9: MEMS Thermal Biosensor

Operating Principle

Changes during reaction:o Enthalpy Change (ΔH)o Change in Concentration(cs)

Concentration change in Flow - injection mode cs = cs0e−λt.

Concentration change in Flow - through mode cs = cs0e−(λA/Q)

Page 10: MEMS Thermal Biosensor

Operating Principle

Power Density ΔP =cs0λV ΔHe−λt (flow - injection mode) ΔP = cs0QΔH(1 − e−λV/Q) (flow - through mode).

Temperature Difference ΔT = ReffΔP

Thermopile Voltage ΔU = KΔP

Page 11: MEMS Thermal Biosensor

Fabrication

The fabrication process starts with a silicon wafer with both sides covered with thermally grown silicon dioxide.

Chromium and nickel are then deposited via sputtering and patterned to form the integrated resistive heaters (nickel), thermopile (nickel/chromium) and bonding pads (chromium).

Tetramethyl ammonium hydroxide is used to etch the wafer from its backside with the oxide there patterned as an etching mask.

Page 12: MEMS Thermal Biosensor

Fabrication

An SU-8 thin film is spin-coated and patterned to form the diaphragms, which upon wafer dicing are made freestanding by gas-phase XeF2 etching.

The microfluidic chip was fabricated from polydimethylsiloxane (PDMS) by replica molding.

PDMS is cast onto the SU-8 mold, cured at 70 ◦C and peeled off to obtain a sheet bearing the microfluidic features including the chambers, channels and weirs.

The fluidic interface is made by inserting Tygon tubing into the inlet and outlet wells and then sealed with epoxy.

Page 13: MEMS Thermal Biosensor
Page 14: MEMS Thermal Biosensor

References

1. Li Wang, David M. Sipe, Yong Xu, Qiao Lin, “A MEMS Thermal Biosensor for Metabolic Monitoring Applications”, Journal of Microelectromechanical Systems, Vol. 17, No. 2, April 2008.

2. B. Danielsson, “Calorimetric biosensors,” Biochem. Soc. Trans., Vol. 19, pp. 26–28, 1991.

3. Martin F. Chaplin, C. Bucke, “Enzyme Technology”, 1991.