Flamebar BW11 - Fire rated ductwork

FLAMEBAR BW11 FIRE RATED

DUCTWORK

Page 1 of 69

FLAMEBAR BW11

CONTENTS

Content 2

Brochures 3-11

Technical and Safety Datasheet 12-30

Specification 31-35

Projects List 36-40

Certificates and Test Report 41-63

Installation 64-80

FLAMEBAR BW11

Brochures

Page 3 of 69

Page 4 of 69

Page 5 of 69

Page 6 of 69

Page 7 of 69

Page 8 of 69

Page 9 of 69

Page 10 of 69

FLAMEBAR BW11

Technical Datasheet

&

Safety Datasheet

Page 11 of 69

Page 12 of 69

Page 13 of 69

Page 14 of 69

Page 15 of 69

Page 16 of 69

Page 17 of 69

Page 18 of 69

Page 19 of 69

Page 20 of 69

Page 21 of 69

SAFETY DATA SHEET

BW11 Spray Grade 1410

1 of 3Page

0Revision

Revision date

1. IDENTIFICATION OF THE SUBSTANCE / PREPARATION AND THE COMPANY

Product name BW11 Spray Grade 1410

Company Firespray International Ltd

Flamebar House, South Road, Templefields, Harlow, Essex, CM20 2AR England

[email protected]

www.firespray.eu.com

Telephone +44 (0)1279 634 230

Fax +44 (0)1279 634 232

Product code 201051

2. COMPOSITION / INFORMATION ON INGREDIENTS

Hazardous ingredients

Conc. CAS Symbols/Risk phrasesEINECS

Diuron (ISO) 0 - 25% 330-54-1 Carc Cat 3; R40 Xn; R22-48/22 N;

R50/53

206-354-4

Description Flame Retardant Coating.

Hazardous ingredients The product is classified as non hazardous.

3. HAZARDS IDENTIFICATION

Main hazards No Significant Hazard

Other hazards The product is classified in accordance with 67/548/EEC.

4. FIRST AID MEASURES

Skin contact Wash off immediately with plenty of soap and water. Remove contaminated clothing.

Seek medical attention if irritation or symptoms persist.

Eye contact Rinse immediately with plenty of water for 15 minutes holding the eyelids open. Seek

medical attention if irritation or symptoms persist.

Inhalation May cause irritation to respiratory system. Seek medical attention if irritation or

symptoms persist.

Ingestion Ingestion may cause nausea and vomiting. DO NOT INDUCE VOMITING. Seek

medical attention if symptons persist.

General information Remove contaminated clothing. Wash all contaminated clothing before reuse.

5. FIRE FIGHTING MEASURES

Extinguishing media Use extinguishing media appropriate to the surrounding fire conditions.

Fire hazards This materail is designed as a fire rated product to BS 476

Protective equipment Wear suitable protective clothing, gloves, eye and respiratory protection.

Print date 12-Apr-2007

Page 22 of 69


2 of 3Page

0Revision

Revision date

6. ACCIDENTAL RELEASE MEASURES

Personal precautions Prevent further spillage if safe. Wear suitable protective clothing, gloves and eye/face

protection.

Environmental precautions Do not allow product to enter drains. Prevent further spillage if safe. Do not flush into

surface water.

Clean up methods Absorb with inert, absorbent material. Sweep up. Transfer to suitable, labelled

containers for disposal.

7. HANDLING AND STORAGE

Handling Avoid contact with eyes and skin. Adopt best Manual Handling considerations when

handling, carrying and dispensing.

Storage Keep in a cool, dry, well ventilated area. Store in correctly labelled containers. Do NOT

allow to freeze. Store in original container.

Suitable packaging Store in original container.

8. EXPOSURE CONTROLS / PERSONAL PROTECTION

Exposure limits

Diuron (ISO) WEL 8-hr limit ppm: -

WEL 15 min limit ppm: -

WEL 8-hr limit mg/m3: 10

WEL 15 min limit mg/m3: -

Engineering measures Ensure adequate ventilation of the working area.

Occupational exposure

controls

Adopt best Manual Handling considerations when handling, carrying and dispensing.

Immediately remove all soiled and contaminated clothing. Keep away from food, drink

and animal feedingstuffs. Wash hands after handling the product.

Respiratory protection Wear suitable respiratory equipment when necessary.

Hand protection Chemical resistant gloves (plastic)

Eye protection Approved safety goggles.

Protective equipment Wear protective clothing.

Environmental exposure

controls

Do not allow product to enter drains.

9. PHYSICAL AND CHEMICAL PROPERTIES

Description Liquid.

Colour Off white.

Odour Characteristic.

pH 7-8

Relative density 1.4 g/cm3 @ 20°C

Water solubility miscible in water.

Viscosity 38-45 poise @ 20°C

VOC (Volatile organic

compounds)

Not Applicable

10. STABILITY AND REACTIVITY

Stability Stable under normal conditions.

Conditions to avoid Do NOT allow to freeze. Store product above 5 °C.


Page 23 of 69


3 of 3Page

0Revision

Revision date

11. TOXICOLOGICAL INFORMATION

Toxicological information No data is available on this product.

12. ECOLOGICAL INFORMATION

Ecotoxicity No data is available on this product.

13. DISPOSAL CONSIDERATIONS

General information Dispose of in compliance with all local and national regulations.

Disposal of packaging Empty containers can be sent to landfill after cleaning, if in compliance with local and

national regulations.

14. TRANSPORT INFORMATION

Further information The product is not classifed as dangerous for carriage.

15. REGULATORY INFORMATION

Risk phrases NSH - No Significant Hazard.

Safety phrases S23 - Do not breathe gas/fumes/vapour/spray.

S51 - Use only in well-ventilated areas.

16. OTHER INFORMATION

Text of risk phrases in

Section 2

R22 - Harmful if swallowed.

R40 - Limited evidence of a carcinogenic effect.

R48/22 - Harmful: danger of serious damage to health by prolonged exposure if

swallowed.

R50/53 - Very toxic to aquatic organisms, may cause long-term adverse effects in the

aquatic environment.

General information The Material Safety Data Sheet complies with C.H.I.P 3.1

Further information The information supplied in this Safety Data Sheet is designed only as guidance for the

safe use, storage and handling of the product. This information is correct to the best of

our knowledge and belief at the date of publication however no guarantee is made to its

accuracy. This information relates only to the specific material designated and may not

be valid for such material used in combination with any other materials or in any other

process.

Maximum content of VOC Not Applicable g/l


Page 24 of 69

APR 06 Issue - 2

FLAMEBAR FIRE RETARDANT GASKET

MATERIAL SAFETY DATA SHEET

1. Substance Identification

Material/Trade Name : FLAMEBAR Fire Retardant Gasket

Material Type : Flexible, flame resistant Nitrile/PVC foam

Company : Firespray International Ltd Flamebar House South Road, Templefields HARLOW CM20 2AR Telephone : +44 1279 634230 Fax : +44 1279 634232 Emergency Telephone : As above

2. Composition

Substance Black Nitrile/PVC foam treated with fire retardants, particulate fillers and UV stabilising agents.

3. Hazard Identification

Hazard Symbols None required. Risk and Safety Not classified as hazardous under the CHIP Regulations 1994 or amended Regulations 1996.

4. First-aid Measures

Inhalation: No adverse effects. Eyes: If contact occurs irrigate with clean water. Mechanical effects only. Skin: No adverse effects. Ingestion: DO NOT induce vomiting as there are no adverse effects.

If a large quantity has been swallowed seek medical advice although the patient is unlikely to be unwell 5. Fire-fighting

Extinguishing Media: Water, CO

2, Powder

Unsuitable Extinguishers: None known. Special Procedures: Firefighters should wear positive pressure, self-contained breathing apparatus. Will emit water, carbon dioxide and carbon monoxide fumes in an intense fire.

6. Accidental Release Measures

Disposal Considerations: Sweep up or clear as for any inert material.

7. Handling and Storage

Handling: Avoid contact with eyes. Dust may cause mechanical irritation. Storage: Store in a cool, dry place below 30

oC. Protect from frost.

8. Exposure Controls

Personal Protection: None. Respiratory Protection: Respiratory protection not normally required. Hand Protection: None required. Eye Protection: Wear goggles when process produces dust. Body Protection: None required.

9. Physical & Chemical Properties Physical State : Cellular solid form Colour : Black Density : 60 – 90 kg/m³ Flash Point : n/a Flammability : Class ‘O’ BS476 Part 6 & 7 Non Ignition BS476 Part 5

10. Stability and Reactivity

Stability: Stable, can react with strong acids and oxidising agents.

11. Toxicological Information

Acute Toxicity : None Health Effects: Inhalation : None Eye Contact : Dust will cause irritation Skin Contact : None.

APR 06 Issue - 2

FLAMEBAR FIRE RETARDANT GASKET

12. Ecological Information

Ecotoxicity: Low solubility. Does not evolve gases which damage the ozone layer.

13. Disposal Considerations

This product is classified as non-hazardous waste under EEC Directive 91/689/EEC. Dispose of in accordance with Local Authority Regulations.

14. Transport Information

UN Class : This material is not classified as dangerous under UN Transport Regulations

UK Packaging Group : No special requirements.

15. Regulatory Information

None

16. Other Information

Compiled according to the CHIP Regulations 1994 (Directive 91/155/EEC) or amended Regulations 1996 N/a – not applicable. N/d – not determined Further H & S Data is available from Firespray International Ltd.

This Data Sheet is compiled to be of assistance, but is without guarantee. Users are responsible for safe working.

FLAMEBAR HOUSE, SOUTH ROAD, TEMPLEFIELDS, HARLOW, CM20 2AR ENGLAND TEL: +44 1279 634230 FAX: +44 1279 634232

e-mail : [email protected] www.firespray.eu.com

This Leaflet has been produced by Firespray International Ltd who have a Policy of continuous Product and System improvement and reserve the right to change Methods and Specifications without notice

mailto:[email protected]

http://www.firespray.co.uk/

FEB 05 Issue -

FLAMEBAR INTUMESCENT ACRYLIC SEALANT

MATERIAL SAFETY DATA SHEET

1. Substance Identification Material/Trade Name : FLAMEBAR Intumescent

Acrylic Sealant Material Type : See Below Company : Firespray International Ltd Flamebar House South Road, Templefields HARLOW CM20 2AR Telephone : +44 1279 634230 Fax : +44 1279 634232 Emergency Telephone : As above. 2. Composition Substance Water-based sealant of an acrylic emulsion plus fillers. 3. Hazard Identification a) Hazard Symbols None required. b) Risk & Safety Not classified as hazardous under the CHIP

Regulations 1994/Amendments 1997 4. First-aid Measures a) Inhalation Remove to fresh air and rest. If symptoms persist, obtain medical advice. b) Eyes Irrigate with water for at least 15 minutes. Obtain medical attention if irritation persists. c) Skin Wash with soap/cleanser and rinse with plenty of

water. d) Ingestion Wash out mouth with water. Give plenty of water to drink. If a large amount has been swallowed, obtain

medical attention. 5. Fire-fighting Measures a) Suitable Extinguishers Foam - Cream Dry Powder - Blue Carbon Dioxide (CO2) - Black b) Unsuitable Extinguishers Do not use water jets c) Hazardous Decomposition Oxides of carbon d) Special procedures Use approved self-contained breathing apparatus

6. Accidental Release Measures a) Exposure Controls Do not allow spill to enter drains and watercourses b) Personal protection Wear suitable protective clothing - See Section 8 c) Disposal Considerations Absorb in inert material such as sand or absorbent

granules Scoop up and place in container to await transfer Dispose of in accordance with Local Authority

requirements. 7. Handling and Storage a) Handling Avoid inhalation of mist Wear suitable protective clothing (See Section 8) b) Storage Store in original containers Store in cool, dry, well ventilated area, off the ground Do not allow to freeze 8. Exposure Controls a) Occupational Exposure Limit : None given in EH 40 b) Biological Exposure Limit : N/A c) Inhalation Use in well ventilated areas d) Skin Avoid skin contact e) Personal Protection Consider suitable respirators where excessive

exposure is likely f) Eyes Wear suitable eye protection if eye contamination

likely 9. Physical & Chemical Properties Appearance : White or off-white paste Odour : Faint esther/alcohol Ph : Alkaline Boiling Point/Range : From 100 deg C Melting Point/Range : N/A Flash Point : N/A Flammability : Non-flammable in liquid state Autoflammability : N/A Explosive Properties : N/A Oxidising Properties : N/A Vapour Pressure : As water Relative Density : 1.3 - 1.4 Solubility : Miscible with water Partition Coefficient : N/D Miscibility : N/D Vapour Density : N/D Evaporation Rate : N/D Viscosity : High

FEB 05 Issue -

FLAMEBAR INTUMESCENT ACRYLIC SEALANT

10. Stability & Reactivity Stability Stable at normal temperatures 11. Toxicological information No toxic effects known Health Effects : May defat the skin Health Effects : Irritating to eyes 12. Ecological Information Not readily biodegradable May harm aquatic organisms and their environment 13. Disposal Considerations Dispose of in accordance with Local Authority

requirements Do not discharge into drains or watercourses 14. Transport Information UN/SI Number : N/A IMO : N/A IATA/ICAO : N/A ADR/RID : N/A Transport Name U K Road Transport : Non-hazardous Hazchem/Kemler Code : N/A Packing Grp : N/A Packing Grp : N/A Item : N/A Marine Pollutant : No 15. Regulatory Information a) Hazard Symbols None required b) Risk & Safety Not classified as hazardous under the CHIP

Regulations 1994/Amendments 1997

c) Other Regulations U K Health & Safety at Work Act 1974 U K Environmental Protection Act 1990 HSE Guidance Note EH 40 U K Special Waste Regulations 1996 U K Control of Substances Hazardous to Health

Regulations 1994 d) Transport Information UN/SI Number : N/A IMO : N/A IATA/ICAO : N/A ADR/RID : N/A Transport Name U K Road Transport : Non-hazardous Hazchem/Kemler Code : N/A Packing Grp : N/A Packing Grp : N/A Item : N/A Marine Pollutant : No 16. Other Information a) Compiled according to the CHIP Regulations

1994/Amendments 1997 b) N/A = not applicable - N/D = not determined c) Further information is available from Firespray

International Ltd.

This Data Sheet is compiled to be of assistance, but is without guarantee. Users are responsible for safe working.

FLAMEBAR HOUSE, SOUTH ROAD, TEMPLEFIELDS, HARLOW, CM20 2AR ENGLAND TEL: +44 1279 634230 FAX: +44 1279 634232

e-mail : [email protected] www.firespray.eu.com

This Leaflet has been produced by Firespray International Ltd who have a Policy of continuous Product and System improvement and reserve the right to change Methods and Specifications without notice


http://www.firespray.co.uk/

FLAMEBAR BW11

Specification

Page 25 of 69

SPECIFICATION - TIÊU CHUẨN KỸ THUẬT

Furthure information please contact us:

Sales and Marketing Department

Tell: 39956 957/ 39955 324

Email [email protected] - [email protected]

FIRE RATED DUCTWORK (2 HOUR) SPECIFICATION

1.0 General Requirements

All fire rated ductwork to be Galvanised Iron, Stainless Steel (or Mild Steel Duct with Antirust Primer), constructed to tested standards and protected with fire resistant coating. The duct to be composite fire duct manufactured to Method 3 of BS5588 Part 9, factory or site produced. Ductwork to be produced in sections and is assembled on site utilising tested fireproof gaskets/sealants. Once erected, to be pressure tested, if required by Engineer, to DW144 and/or SMACNA standards, in line with the pressure classification of the duct being installed. The coating shall be of minimum 0.7mm (dry film) thickness.

2.0 The Specification of Fire Rated Ductwork

2.1 Proof of Fire rated ductwork constructed for ventilation/smoke extract systems tested to BS476 Part 24 (1987) and ISO6944 (1985) for two hours Stability and Integrity shall be submitted. When used as smoke extract, duct to maintain a minimum of 75% cross-sectional area along its whole length for at least two hours. Evidence of test must be submitted. The Fire Rated Ductwork to be protected with fire resisting coating materials to specifications by manufacturer. Composition of the coating materials shall be of encapsulating compound, non-hazardous copolymer emulsion and aggregates. Intumescent coating materials shall not be accepted. 1.2.1 Fire rated ductwork constructed for kitchen

extract systems to be tested to BS476 Part 24 (1987) and ISO6944 (1985) for two hours Stability and Integrity. Suitable insulation cladding of mineral wool material

TIÊU CHUẨN KỸ THUẬT

1.0 Yêu cầu chung

Tất cả ống gió chống cháy làm từ tôn mạ kẽm, thép không rỉ(hoặc là ống thép mềm với lớp sơn chống rỉ) phải được kiểm tra theo tiêu chuẩn và được bảo vệ bằng một lớp sơn phủ chống cháy. Ống gió có thể được gia công tại xưởng hoặc công trường và theo phương pháp 3 của tiêu chuẩn Anh BS5588 chương 9. Ống gió được sản xuất từng phần và nối với nhau bằng roong và keo được kiểm định chống cháy. Mỗi khi được lắp nối,nếu có kỹ sư yêu cầu thì phải được kiểm tra áp suất theo tiêu chuẩn DW144 và/hoặc SMACNA phù hợp với sự phân loại áp suất của ống gió. Lớp sơn bảo vệ có độ dày ít nhất là 0.7mm (sau khi khô).

2.0 Tiêu chuẩn kỹ thuật của ống gió chống

cháy. 2.1 Tài liệu về ống gió chống cháy cho hệ thống thông gió/hút gió phải được kiểm tra theo tiêu chuẩn BS476 chương 24(1987) và ISO 6944(1985) trong 2 giờ về tính ổn định và nguyên vẹn, phải được kiểm tra. Ống gió hút khói, phải được giữ nguyên ít nhất 75% mặt cắt của chiều dài trong suốt 2 giờ. Tài liệu về kết quả kiểm tra phải được đệ trình. Ống gió chống cháy phải được bảo vệ bằng lớp sơn theo tiêu chuẩn nhà sản xuất. Thành phần vật liệu của lớp sơn bề mặt phải là hợp chất đồng nhất, chất nhũ không độc hại và đồng chất. Lớp phủ phồng không được chấp nhận cho hệ này. 1.2.1 Cấu tạo của ống gió chống cháy cho hệ hút khói nhà bếp phải được kiểm định theo tiêu chuẩn Anh BS476 chương 24(1987) và ISO6944 (1985) trong vòng 2 giờ về tính ổn định và nguyên vẹn. Kỹ sư sẽ yêu cầu lớp cách nhiệt bằng bông khoáng phù hợp.

Page 26 of 69




Tell: 39956 957/ 39955 324


shall be added as required by the engineer.

1.2.2 The size of the Fire Rated Duct system

may be extended up to 10 metres wide x 3 metres high without adversely affecting the fire resistant of the duct systems in terms of criteria of BS476: Part 24: 1987.

1.2.3 Fire rated ductwork to have UL

(Underwriters Laboratories) classification and has been tested by UL in the USA to determine compliance with NFPA 90A ( Installation of Air Conditioning and Ventilation Systems ) for flame spread and smoke development with the following results:

NFPA Stipulation

Flame Spread not

to Exceed 25

Smoke Development

not higher than 50

Fire Rated Duct Results

9.4 0.2

1.2.4 Fire rated ductwork to have passed hard body impact resistant test to BS EN 1128: 1996. At impact energy of 52.46 J, no penetration of test specimen, no de-bonding, cracking and other failure of the coating material at impact location. Test report to be submitted.

1.2.5 The fire duct to have been tested by ETL

Intertek for 2 hours to ASTM-E119, including the hose stream test with water pressure of 207 KPa (30 psi) for 2½ minutes.

1.2.6 The fire coating to be non-hydroscopic and

have been tested for over 2000 hours of exposure to alternate UV and condensation cycling, with no adverse

1.2.2 Kích thước của hệ thống ống gió chống cháy có thể lên tới 10m dài x 3m cao, không bị ảnh hưởng bất lợi tới tính chống cháy của hệ thống ống gió theo những điều kiện tiêu chuẩn của BS476 chương 24 năm 1987. 1.2.3 Ống gió chống cháy phải được phân loại theo điều kiện UL và được kiểm tra bởi UL ở Mỹ để quyết định tính phù hợp với tiêu chuẩn NFPA 90A (Lắp đặt hệ thống điều hòa không khí) cho cháy lan và sinh khói theo kết quả sau đây:

Điều kiện của NFPA

Cháy lan không được vượt quá 25

Sinh khói không được cao hơn

50

Kết quả của ống gió chống cháy

9.4 0.2

1.2.4 Ống gió chống cháy phải đạt được việc kiểm tra va chạm cho thân ống cứng theo tiêu chuẩn BS EN 1128 năm 1996. Khi kiểm tra áp lực của 52.46J, mẫu test không cần qua tường, không bong dán, không nứt gãy và những lỗi khác tại điểm va chạm. Kết quả kiểm định phải được trình duyệt. 1.2.5 Ống gió phải được kiểm tra bởi ETL intertek trong vòng 2h với ASTM-E119, bao gồm kiểm tra dòng chảy trong ống với áp lực nước là 207Kpa(30 psi) trong vòng 150 phút. 1.2.6 Lớp phủ chịu lửa không hút ẩm và được kiểm định hơn 2000 giờ với sự biển đổi của UV và vòng tròn ngưng tụ,không bị ảnh hưởng lên bề mặt ống gió được phủ lớp sơn.

Page 27 of 69




Tell: 39956 957/ 39955 324


effect on the condition of the coated duct. 1.3 Installation 1.3.1 The fire duct support system should be

located at a maximum of 1500mm centres, the size of the hangers and bearers upgraded to account for reduction in tensile strength of steel due to fire. Proof, in the form of test or assessment report to BS476 Part 24 and ISO6944 that suitable size hangers and bearers upgraded to account for the reduction in tensile strength of steel due to fire from 430N/mm2 to 10N/mm2 for 2 hours, shall be submitted.

1.3.2 All gaskets and sealants to be non-combustible and installed as fire tested to BS476 Part 24 and

shall be supplied by the same manufacturer. 1.3.3 The Gasket shall be fire retardant Intumescent. Tape Gasket which is a highly flexible, chemically

inert, non toxic foam tape, designed to seal flange joints and other metal surfaces that require to be sealed together. It shall be self adhesive and easy to peel, will not shrink or degrade in normal use and is unaffected by water or moisture. The Gasket shall be of dimensions 15mm wide x 5mm thick x 15metre rolls for flanges up to 40mm.

1.3.4. The sealant material shall be a one part ready to use Intumescent Fire Retardant Acrylic Sealant. It

shall be non-flammable in liquid state and not classified as hazardous under the CHIP Regulations 1994/Amendments 1997. The intumescent fire retardant sealant has been tested to BS 476 Part 22/1987 (ISO 834) in specified joint configurations.

1.3.5 The fire rated duct shall be connected to

1.3 Lắp Đặt

1.3.1 Hệ thống thanh treo phải được lắp đặt với khoảng cách tối đa là 1500mm. Kích thước của thanh treo,giá đỡ được tính toán để giảm sự kéo dài trong quá trình cháy. Trong báo cáo kiểm tra và đánh giá của tiêu chuẩn BS476 chương 24 và ISO 6944 thể hiện kích thước của thanh treo, giá đỡ được tính toán để giảm sự kéo dài trong quá trình cháy là từ 430N/mm2 xuống 10N/mm2 trong vòng 2 giờ.

1.3.2 Tất cả roăng và keo phải là không bắt cháy

và được lắp đặt như là đã được kiểm tra chống cháy theo BS476 chương 24 và nên được cung cấp bởi cùng một nhà sản xuất.

1.3.3 Roăng phải là loại phồng lên và làm cháy

chậm. Roăng là loại dẻo, không có chất độc hại, được thiết kế để nối mặt bích và những bề mặt kim loại khác mà được yêu cầu gắn với nhau. Nó phải là dạng tự dính và dễ găm vào, không bị co rút hoặc biến chất ở điều kiện sử dụng thông thường và không bị ảnh hưởng từ nước và chất ẩm. Một cuộn Roăng có kích thước là rộng 15mm x dày 5mm x dài 15mm được sử dụng cho dạng mặt bích lên tới 40mm.

1.3.4 Keo là một dạng keo acrylic phồng lên để

cháy chậm. Nó phải là dạng chất lỏng không bắt lửa và được phân loại không phải là chất độc hại theo điều luật CHIP 1994/ sửa đổi năm 1997. Keo chống cháy dạng phồng phải được kiểm tra theo tiêu chuẩn BS476 chương 22 năm 1987 (tương đương ISO834) trong những cấu hình nối được quy định.

1.3.5 Ống gió chống cháy phải được lắp với quạt

Page 28 of 69




Tell: 39956 957/ 39955 324


the fans with the use of fire rated flexible connections with fire certification to BS476 Part 20.

1.3.6 All access doors/inspection covers and test

holes shall be suitably positioned in relation to the access provided by the false ceiling or other means of concealment supplied and fitted by the building contractor.

1.3.7 The fire rated ductwork must be

manufactured and erected in line with the requirements of BS 476 Part 24 (1987) and ISO6944 (1985).

với việc sử dụng những mối nối linh hoạt được chứng nhận theo tiêu chuẩn BS476 chương 20.

1.3.6 Tất cả các cửa vào/ bề mặt kiểm tra và lỗ kiểm tra phải được định vị phù hợp với đầu vào được cung cấp bởi trần giả hoặc nhà thầu sẽ che kín bằng những phương pháp khác.

1.3.7 Ống gió chống cháy phải được sản xuất và lắp ráp phù hợp với yêu cầu của BS 476 chương 24 (1987) và ISO 6944(1985).

Page 29 of 69

FLAMEBAR BW11

Projects list

Page 30 of 69

FLAMEBAR BW11 FIRE RATED DUCTWORK A SELECTION OF INTERNATIONAL PROJECTS

Vietnam MGM Hotram strip, Ba Ria-Vung Tau Novotel Han river hotel, Da Nang Crescent Shopping Mall, HCMC Silver Sea Tower, Vung Tau JW Marriot Hanoi Hotel, Hanoi Indochina plaza, Ha Noi Trang Tien Plaza, Ha Noi West Lake Inter-Continental Hotel, Hanoi

Dubai Burj Al Arab International 7* Hotel (tallest hotel in the world)

Burj Khalifa Tower (tallest building in the world)

Emirates Towers Jumeirah Beach Hotel Festival City Shopping Mall Mall of the Emirates DIFC Towers (6 buildings) Raffles Hotel & Wafi Mall The Dubai Mall (with indoor ski arena) Bur Jaman Center Burj Dubai Lake Hotel Movenpick Hotel & Spa & Oceana Residence Shangri-La Hotel Al Jaber Tower

Abu Dhabi Snow Dome Marine Mall Dubai International Shopping Centre Intercontinental Hotel Twin Towers Sheikh Bin Butti Building Al Jimi Hypermarket

Sharjah Sharjah University Shop at Mall of Emirates Mega Mall

Bahrain Bahrain International Airport World Trade Centre, Bahrain Bahrain Financial Harbour

Muscat Muscat Retail Park Water Purification Plant

Saudi Arabia King Fhad’s University

Oman City Centre Mall Expansion Barr Al Jissa Village Hotel Shangri-La Hotel & Resort Qatar Sports Tower, Asian Games Commercial Bank Plaza Qatar Insurance Building West Bank Residential Tower Al Reem Tower Ceremonial Tower Al Wosail Tower Al Fardan Tower Australia Office Building@ No.3 Hasler Road, Osborne Park Perth Office Building@ 226 Adelaide Terrace Perth Woodside Building @240 St Georges Terrace, Perth Four Brisbane Hospitals Perth Cancer Hospital India Delhi Metro Railway Barbados The Sands Hotel

Page 31 of 69

mailto:@240

Brunei Royal Residence at Jln Tutong Ministry of Foreign Affairs (MOFA) Building Banquet Hall, The Empire Hotel and Country Club, Brunei Yayasan Secondary School Meragang Secondary School Radio Television Complex, Sungai Akar I Maraburong Prison Legislative Council Building, Bandar Seri Begawan slamic Bank of Brunei Brunei International Airport University of Brunei, Darussalam Brunei Parliament House

China - Hong Kong SAR Cathay Pacific Cargo Terminal Hennessey Centre Redevelopment Tamar Government Headquarter Atrium Hotel MTR Austin Station - KDB200 (Kowloon-Canton Railway Corporation) MTR Admiralty Station (replacement) Hong Kong Cricket Club Regal Airport Hotel (extension) Landmark East (Phase 6) Landmark Mandarin Hotel Mandarin Oriental Hotel Jardine House Pacific Place Podium & Restaurant Lincoln House, Taikoo Place Oxford House, Taikoo Place Devon House, Taikoo Place Aberdeen Market (upgrade) Sheung Wan Market (update) St. Teresa Hospital Tang Shiu Kin Hospital (re-modeling) DHL Central Asia Hub Charter House Exchange Square Tower 2 Chek Lap Kok Airport Shatin Heritage Museum Olympia Plaza Tradeport Logistics Centre

China - Macau Venetian Macau Parcel 5&6 (Hotels) New Taipa Immigration Office Building Macau University of Science & Technology City of Dreams Ponte 16 Phase 2 (Commercial & Shopping) Amaral Macau Public Car park Le Royal Arc Casino & Retail Complex New Yaohan Departmental Store MGM Casino (Fire rated enclosure) Wynn Resorts & Casino (Phase 1 &2) Taipa Hotel, Resort & Casino Fisherman’s Wharf Complex & Casino

Las Vegas Sands Hotel & Casino Galaxy Starworld Hotel & Casino The Venetian Macau (fire rated enclosure) Holiday Inn Hotel & Casino Indonesia CIBA Vision Building Batam Malaysia National Library Jln Tun Razak Glomac Tower Jln Pinang DBKL Training Centre Jln Cheras PPUM Petaling Jaya Malaysian Milk Building Klang University Putra Malaysia Serdang General Hospital Kuala Lumpur Menara Maxis, Jalan Ampang Bank Negara (New Financial Centre) Mont Kiara Le Grande Condominium Taipan Star Condominium Tanjong Bin Power Station (Johor) Tanjung Pelepas Warehouse (Johor) Mid Valley City Phase 2 – The Garden Wing Bank Negara (Central) Note Printing Centre Sungai Buloh Hospital Ministry of Finance Building, Putrajaya Ampang Tower Office Building Menara Landmark (shopping centre) KLCC Convention Centre La Grand Condominium, Mont Kiara Traders Hotel Central Bank Printing Facility Ericsson Headquarters, Cyberjaya Kuala Lumpur International Airport (main terminal, satellite building & contact pier) Palace of Justice, Putrajaya Syariah Court, Putrajaya Aquaria – KLCC Shangri-La Hotel Singapore NUS CREATE Research Building SengSiong Hypermarket Vista Condominium Central Mall Underground Military Complex@Jalan Gali Batu Nanyang Technological University – Teaching Facility Starville Condominium Cuppage Plaza – Refurbishment Majestic Hotel@ Bukit Pasoh IKEA Tampines Singapore Botanic Garden (Herbarium) Kallang Leisure Park Robertson Walk Condominium Haw Par Villa Annex Museum Cuppage Plaza (refurbishment) Bugis Junction Tan Tock Seng Hospital Singapore Airlines Headquarters

Page 32 of 69

mailto:Complex@Jalan

Ngee Ann City - Refurbishment Swissotel Merchant Court Hotel Sijori Resort, Sentosa St Andrew’s Mission Hospital Singapore Recreation Club

Taiwan (R.O.C) Military 1011 Complex Kaohsiung Medical University Hospital Kaohsiung Post Office

Thailand Mega@Bangna (with IKEA) National Science & Technology Development Agency Phase 1 & 2 Park Venture Hotel Plaza Four Point Hotel W Hotel Land & House Condo & Plaza Sathorn Square Veranda Sofitel Bangkok Gateway Ekamai Sirirat Hospital Renaissance Hotel Central Festival Pattaya Athenee Hotel Tower & Plaza (Extension) Athenee Residence Marriott Courtyard Hotel Ratchada Tower Asoke Complex Le Meridien Hotel The Soffitel Sukhumvit Hotel The Zest Shopping & Residential Complex The Tempo Commercial Complex @Thonglor Le Cordon Blue Dusit Academy, Dusit Thani Hotel, Bangkok Bank of Thailand (New Office) Grand Hyatt Erawan Hotel Holiday Inn Silom Hotel (Renovation) King Power Complex Impact Challenger Convention Centre (one of the largest convention centres in Asia)

USA (New York) GE World Research, New York

USA (Massachusetts) One First Street MIT Brookhaven Northpoint Lahey Clinic Broad Institute (MIT) Convention Center Hotel Boston University (Metcalf Hall)

Harvard Bio Harvard College (Hamilton Hall) McCallan Building Childrens’ Hospital USA (Florida) Hampton’s, Aventura Plaza on Brickell, Aventura One Bal Harbour, Bal Harbour 55 Miracle Mile, Coral Gables Orchid Beach, Deerfield Beach DCOTA, Dania NSU Performing & Visual Arts, Davie NSU Dormitory, Davie Palazzo Del Mare, Fisher Island Navona, Fort Myers Q Club, Fort Lauderdale Capri, Fort Lauderdale Sands, Key Biscayne Ocean Tower II, Key Biscayne Madeira, Marco Island Marina Blue, Miami Biscayne Landings 1 & 2, Miami Aversana, Naples Tuscany at Hammock Dunes, Palm Coast Oceanside, Pompano Sunny Isle City Hall, Sunny Isles Beach Residence, Sarasota Esplanade Grand, West Palm Beach USA (Wisconsin) Epic Learning Centre St Mary’s Hospital Vernon Hospital St Clare Meadows Nursing Home CUNA – Mutual Group Insurance St Lukes Medical Centre Ambassador Hotel St Mary’s Catholic Center High School Atla Shaam USA (Texas) Galveston National Lab American First National Bank Houston Pavilion Shopping Mall Energy Center Office Building

Page 33 of 69

mailto:Mega@Bangna

mailto:@Thonglor

PROJECTS IN VIETNAM

Marriott Hotel

Silver Sea Tower

The Crescent - Shopping mall

Ho Tram Strip

Trang Tien plaza

Novotel Han river

Indochina plaza

West Lake Inter-Continental Hotel

Liberty Hotel

Aeon Mall

Shangrila Hospital

Mega Hoan Kiem

Riviera Point

Des Art Saigon Hotel

LIM 2 Tower

SSG Van Thanh (Pearl Plaza)

Landmark Cambodia

Masteri Thảo Điền

FLAMEBAR BW11

Certificates &

Test Reports

Page 35 of 69

UL Online Certifications Directory Home Quick Guide Contact Us UL.com

HNNX.R18284 Coated Ducts

Page Bottom

Coated Ducts

See General Information for Coated Ducts

FIRESPRAY INTERNATIONAL LTD R18284 FLAMEBAR HOUSE

SOUTH RD

TEMPLEFIELDS

HARLOW, ESSEX CM20 2AR UNITED KINGDOM

FLAMEBAR BW11 Fire Rated Ductwork for use in Ventilation Duct Assembly No. V-6; and Uninsulated Ventilation Duct Assembly Nos. V-5 and V-18.

Last Updated on 2010-05-28

Questions? Print this page Notice of Disclaimer Page Top

Copyright © 2011 Underwriters Laboratories Inc.®

The appearance of a company's name or product in this database does not in itself assure that products so identified have been manufactured under UL's Follow-Up Service. Only those products bearing the UL Mark should be considered to be Listed and covered under UL's Follow-Up Service. Always look for the Mark on the product.

UL permits the reproduction of the material contained in the Online Certification Directory subject to the following conditions: 1. The Guide Information, Designs and/or Listings (files) must be presented in their entirety and in a non-misleading manner, without any manipulation of

Page 38 of 69

http://database.ul.com/cgi-bin/XYV/template/LISEXT/1FRAME/index.html

http://database.ul.com/cgi-bin/XYV/template/LISEXT/1FRAME/quickguide.html

http://database.ul.com/cgi-bin/XYV/template/LISEXT/1FRAME/gassist.html

http://www.ul.com/

http://database.ul.com/cgi-bin/XYV/template/LISEXT/1FRAME/showpage.html?name=HNNX.R18284&ccnshorttitle=Coated+Ducts&objid=1074297363&cfgid=1073741824&version=versionless&parent_id=1073987946&sequence=1#PAGEBOTTOM



http://database.ul.com/cgi-bin/XYV/template/LISEXT/1FRAME/showpage.html?&name=HNNX.GuideInfo&ccnshorttitle=Coated+Ducts&objid=1074297359&cfgid=1073741824&version=versionless&parent_id=1073987946&sequence=1

http://database.ul.com/cgi-bin/XYV/cgifind.new/LISEXT/1FRAME/srchres.html?collection=/data3/verity_collections/lisext&vdkhome=/data3/verity_sw_rev24/common&SORT_BY=textlines:asc,ccnshorttitle:asc&query=V-6+%3cIN%3eFile_Number+and+HNLJ*%3cIN%3eCCN

http://database.ul.com/cgi-bin/XYV/cgifind.new/LISEXT/1FRAME/srchres.html?collection=/data3/verity_collections/lisext&vdkhome=/data3/verity_sw_rev24/common&SORT_BY=textlines:asc,ccnshorttitle:asc&query=V-5+%3cIN%3eFile_Number+and+HNLN*%3cIN%3eCCN

http://database.ul.com/cgi-bin/XYV/cgifind.new/LISEXT/1FRAME/srchres.html?collection=/data3/verity_collections/lisext&vdkhome=/data3/verity_sw_rev24/common&SORT_BY=textlines:asc,ccnshorttitle:asc&query=V-18+%3cIN%3eFile_Number+and+HNLN*%3cIN%3eCCN

http://database.ul.com/cgi-bin/XYV/template/LISEXT/1FRAME/gassist.html

http://database.ul.com/cgi-bin/XYV/template/LISEXT/1FRAME/gdisclaim.html

http://database.ul.com/cgi-bin/XYV/template/LISEXT/1FRAME/showpage.html?name=HNNX.R18284&ccnshorttitle=Coated+Ducts&objid=1074297363&cfgid=1073741824&version=versionless&parent_id=1073987946&sequence=1#PAGETOP

http://www.ul.com/global/eng/pages/corporate/onlinepolicies/copyrightnotice/

the data (or drawings). 2. The statement "Reprinted from the Online Certifications Directory with permission from Underwriters Laboratories Inc." must appear adjacent to the extracted material. In addition, the reprinted material must include a copyright notice in the following format: "Copyright © 2011 Underwriters Laboratories Inc.®"

Page 39 of 69

Loss Prevent on Certification BoardLPCSThis is to certify

FIRE5PRAY INTERNATIONAL LIMITEDFlamebar House, South Road, Templefields, Harlow, Essex, CM20 2AR

is authorised to use the LPCB mark in association with theproduct(s) listed in this certificate and appendix.

FLAMEBAR BW11(refer to attached appendix for details)

which has complied with the requirements of the following:

B5476 - 24 : 1987 - Fire test on building materials andstructures - Part 24: Method for determination of the fire

resistance of ventilation ducts

Certificate No. 415a Issue No. 10

Date of Issue 21 December 2012This certificate is valid until withdrawn by LPCB.To check the validity and the authenticity of this certificate pleasevisit our website www.RedBookLive.com or contact us.

Signed on behalf of the LPCB

~~

Name: T BakerLPCB is part of BRE Global Ltd., Garston, Watford WD25 9XX. Tel +441(0)1923 664100

Fax +44 (0)1923 664603 www.RedBookLive.comThis certificate remains the property of BRE Global Ltd and is issued subject to terms and conditions

and is maintained and held in force through regular surveillanc:e activities.

BF668 Revision1.1 Page 1 of 5 ©BRE Global Ltd, 2012

Loss Prevention Certification Board

LPCBAPPENDIX TO CERTIFICATE NO. 415a

FIRESPRAY INTERNATIONAL LIMITED

Product Duct Type Condition Type of Insulation Fire Resistance LPCBName Insulation Thickness Integrity I Insulation Ref. No.

Stability (min)(min)

Flamebar Ventilation Fire outside - - 120 15 415a/01BW11 duct - - 240 15

45kg/m3 25mm 120 6045kg/m3 60mm 120 6060kg/m3 40mm 120 9060kg/m3 50mm 120 11860kg/m3 120mm 120 120

105kg/m3 SOmm 120 120105kg/m3 80mm 120 120105kg/m3 SOmm 240 208

60kg/m3 120mm 240 24010Skg/m3 80mm 240 240105kg/m3 120mm 240 24010Skg/m3 100mm** 240 240

Flamebar Ventilation Fire inside - - 120 - 41Sa/01BW11 duct - - 240 -

4Skg/m3 2Smm 120 304Skg/m3 60mm 120 3060kg/m3 50mm 120 45

105kg/m3 50mm 120 6060kg/m3 120mm 120 90

105kg/m3 80mm 120 90105kg/m3 120mm 120 120105kg/m3 100mm** 120 120

60kg/m3 120mm 240 90105kg/m3 80mm 240 90105kg/m3 120mm 240 120105kg/m3 100mm** 240 120

This certificate is valid until withdrawn by LPCB.To check the validity and the authenticity of this certificate pleasevisit our website www.RedBookLive.com or contact us.

Signed on behalf of the LPCBPage 2 of 5

Date of Issue 21 December 2012

Name: T BakerIssue No. 10

LPCB is part of BRE Global L d., Garston, Watford WD25 9XX. Tel +44 (0)1923 664100Fax +44 (1)1923664603 www.RedBookLive.com

This certificate remains the propert of BRE Global Ltd and is issued subject to terms and conditionsand is maintained and held in force through regular surveillance activities.

BF668 Revision 1.1 Page 2 of 5 ©BRE Global Ltd, 2012

Loss Prevention Certification Board





Flamebar Smoke Fire outside - - 120 15 415al01BW11 outlet duct - - 240 15

45kg/m3 25mm 120 6045kg/m3 60mm 120 6060kg/m3 40mm 120 9060kg/m3 50mm 120 11860kg/m3 120mm 120 120

105kg/m3 50mm 120 120105kg/m3 80mm 120 120105kg/m3 50mm 240 208


Flamebar Smoke Fire inside - - 120 - 415al01BW11 outlet duct - - 240 -


105kg/m3 50mm 120 6060kg/m3 120mm 120 90

105kg/m3 80mm 120 90105kg/m3 120mm 120 120105kg/m3 100mm** 120 120

60kg/m3 120mm 240 90105kg/m3 80mm 240 90105kg/m3 120mm 240 120105kq/m3 100mm** 240 120




Issue No. 10Name: T Baker

LPCB is part of BRE Global Ltd., Garston, Watford WD25 9XX. Tel +44 (0)1923 664100Fax +44 (0)1923664603 www.RedBookLive.com

This certificate remains the property of BRE Global Lid and is issued SUbject to terms and concmoneand is maintained and held in force through regular surveillance activities.


Loss Prevention Certification Boa r d





Flamebar Kitchen Fire outside - - 120 15 415a/01BW11 extract duct - - 240 15

60kg/m3 50mm 120 2860kg/m3 60mm 120 30

105kg/m3 50mm 120 4460kg/m3 120mm 120 45

105kg/m3 80mm 120 45105kg/m3 100mm** 120 150105kg/m3 50mm 240 44


Flamebar Kitchen Fire inside - - 120 - 415a/01BW11 extract duct - - 240 -


105kg/m3 50mm 120 6060kg/m3 120mm 120 90

105kg/m3 80mm 120 90105kg/m3 120mm 120 120105kg/m3 100mm** 120 12060kg/m3 120mm 240 90

105kg/m3 80mm 240 90105Kg/m3 120mm 240 120105kg/m3 100mm** 240 120




Issue No. 10Name: T Bakeri

LPCB is part of BRE Global Ltd., Garston, Watford WD25 9XX. Tel +44 (0)1923 664100Fax +44 (0)1923 664603 www.RedBookLive.com

This certificate remains the property of BRE Global LId and is issued subject to terms and conditionsand is maintained and held in force through regular surveillance activities.

BF668 Revision 1.1 Page 4 of 5 ©BRE Global LId, 2012

Loss Prevention Cert ficat on Boa r d



* Refers to internal face inside furnace.Includes 500mm x 25mm thick x 105kg/m3 density mineral wool collar around duct on both sides ofpenetration seals through fire compartment walls and floors.

**

Notes:

1 All ducts are protected with O.7mm to 1.0mm nominal thickness of Flamebar BW11 Fire Proofing.2 Maximum hanger centres are 1500mm for fire ratings up to two hours and 1000mm for fire ratings up to

four hours.3 The 50mm thick x 60kg/m3 density mineral wool insulation may be in the form of either slabs or wrap4 Please refer to BRE Global Report CC88343 Review 4 Issue 2 for minimum wall thickness for the steel

ducts protected with Flamebar BW11 Fireproofing.




Issue No. 10Name: T Baker

LPCB is part of BRE Global Ltd., Garston, Watford WD25 9XX. Tel +44 (0)1923 664100Fax +44 (0)1923 664603 www.RedBookLive.com

This certificate remains the property of BRE Global Ltd and is issued subject to terms and conditionsand is maintained and held in force through regular surveillance activities.


BF040 Rev 9.5 Page 1 of 1 © BRE Global Ltd, 2013

Certificate of Management System Registration Certificate Number: 415 Issue: 10

Firespray International Limited

having complied with the requirements of:

ISO 9001:2008 Quality Management Systems – Requirements

are authorised to use the LPCB Certification Mark on stationery and publications related to the following products and/or services:

Firespray International Limited

Flamebar House South Road Templefields Harlow Essex CM20 2AR UK

Scope: Manufacture and installation of fire resistant ductwork systems and penetration seals.

This certificate is maintained and held in force through regular surveillance activities.

Tracie Hunter 11 January 2014 10 January 2017 28 September 1998 Signed for LPCB Technical Manager Date of This Issue Expiry Date Date of First Issue

This certificate and appendix remains the property of BRE Global Limited and is issued subject to terms and conditions (for details visit www.redbooklive.com/terms).

To check the validity of this certificate and appendix please scan the QR tag, visit www.redbooklive.com/check or contact us.

LPCB is part of BRE Global Ltd., Garston, Watford WD25 9XX. T: +44 (0)1923 664100 F: +44 (0)1923 664603 E: [email protected]

http://www.redbooklive.com/terms)

http://www.redbooklive.com/check


Page 45 of 69

Page 46 of 69

Page 47 of 69

Page 48 of 69

Page 49 of 69

Page 50 of 69

Page 51 of 69

Page 52 of 69

FLAMEBAR BW11

Installation

Page 58 of 69

Duct fabrication, fixing of flanges to Flamebar BW11

Standard Drawing, checking of ducts to ensure correct standard.

De- Greasing of duct - before spraying Flamebar BW11, clean the duct of any grease or dust & hose it with water

Ducts dried & ready for spray – also check to ensure

sealants are applied correctly (ducts must be properly dried before spraying).

Must be use tested fireproof gasket and

sealants.

Before using, you have to stir (from 3-5 minutes) to

have a smooth spraying and surface.

Preparing the duct for spraying - apply Flamebar BW11 coating to the flange/duct connections, corner, gaps.

Spraying of Flamebar BW11.

With installed ductwork, application of Flamebar coating is

similar but must be notice:

1.Ductwork must be cleaned off oil, grease, dust... Fire

retardant gasket and sealant must be used.

2. Ensure enough space to spray/brush Flamebar coating

to 4 sides of ductwork with minimum thickness 0.7mm.

3. Must stir Flamebar coating well before using If brush

and/or roller are used to install Flamebar coating.

Check the thickness of coating with gauge. Ensure all dry

film thickness must be at least 0.7mm

Gauge Thickness Equipment .

Can buy from:HCM: 290/2/T5 Dương Bá Trạc, Phường 1, Q.8 .

HN: 217/2 La Thành, P. Giảng Võ, Quận Ba Đình.http://www.tcvn.com.vn/vi/san-pham/do-do-day-lop-son-phu-elmetron-tcvn-huatec-mitech-coating-thickness-gauge.html

Some examples of air compressor and hopper gun (output

minimum 6mm to 7mm)

Note: TCBM doesn’t supply these equipments.

FOR FUTHER INFORMATION PLEASE REFER TO TCBM.FOR FUTHER INFORMATION PLEASE REFER TO TCBM.FOR FUTHER INFORMATION PLEASE REFER TO TCBM.FOR FUTHER INFORMATION PLEASE REFER TO TCBM.

(+84 8) 39956957 / (+84 4) 666 40787

[email protected]

16