31
DRILLING BITS JAMES A. CRAIG

Drilling Engineering - Drill Bit

Embed Size (px)

DESCRIPTION

Petroleum Engineering, Drilling Engineering, Drilling Bits

Citation preview

Page 1: Drilling Engineering - Drill Bit

DRILLING BITS

JAMES A. CRAIG

Page 2: Drilling Engineering - Drill Bit

Table of Contents

Types of Bit Drag Bit Roller Cutter Bit

Drill Bit Classification Drag Bit Classification Roller Cutter Bit Classification

Drill Bit Grading Tooth Wear/Loss Bearing Wear Gauge Wear

Page 3: Drilling Engineering - Drill Bit

Types of Bit Drag Bit Roller Cutter Bit

Drill Bit Classification Drag Bit Classification Roller Cutter Bit Classification

Drill Bit Grading Tooth Wear/Loss Bearing Wear Gauge Wear

Page 4: Drilling Engineering - Drill Bit

Table of Contents Types of Bit

Drag Bit Roller Cutter Bit

Drill Bit Classification Drag Bit Classification Roller Cutter Bit Classification

Drill Bit Grading Tooth Wear/Loss Bearing Wear Gauge Wear

Page 5: Drilling Engineering - Drill Bit

DRILLING BITS

A steel-toothed piece of equipment attached to the lower end of the drillstring in order to: crush, scrape and, grind formation loose.

The two types available are: drag bits rolling cutter bits

Page 6: Drilling Engineering - Drill Bit

Drag Bits

They consist of fixed cutter blades that are integral with the body of the bit and rotate as a unit with the drillstring. The cutting element consists of steelcutters, diamond, or polycrystalline diamond compact (PDC).

Steelcutter bits the serrated steel blades are set at different angles (e.g.

a fishtail bit). Natural diamond bits

the face or crown of the bit consists of many diamonds set in a tungsten carbide matrix.

Page 7: Drilling Engineering - Drill Bit

Polycrystalline diamond compact (PDC) bits a layer of synthetic PDC is bonded to a cemented

tungsten carbide, it contains many diamond crystals bonded together. The sintered PDC compact is bonded either to a tungsten carbide bit-body matrix or to a tungsten carbide stud that is mounted in a steel bit.

Thermally stable polycrystalline (TSP) bits these bits are manufactured in a similar fashion to PDC

bits but are tolerant of much higher temperatures than PDC bits.

Page 8: Drilling Engineering - Drill Bit
Page 9: Drilling Engineering - Drill Bit

Roller Cutter Bits

They have two or more cones containing the cutting elements which rotate about the axis of the cone as the bit is rotated at the bottom of the hole. The 3-cone rolling cutter bit is by far the most common.

Important factors to consider in this type of bit are: structural materials, bearing-seal-lubricating design, cutting structure arrangements, and hydraulic arrangements.

Page 10: Drilling Engineering - Drill Bit
Page 11: Drilling Engineering - Drill Bit
Page 12: Drilling Engineering - Drill Bit

Structural materials steels with appropriate yield strength, impact resistance,

machineability, and heat-treated properties are usually selected. Cones are commonly heat treated and made of NiMo-steel, teeth are sometimes made of NiCrMo-steel

Bearing-seal-lubricating design they function as a unit and they must be able to

withstand large impact loads, chemicals in the drilling fluids, and high temperature.○ Sealed bearings – grease lubricant (much longer life)

– pressure surges can cause leak○ Journal bearings – wear-resistant hard surface on journal

– O-ring seal and grease– solid lubricant inside cone journal race

Page 13: Drilling Engineering - Drill Bit
Page 14: Drilling Engineering - Drill Bit

Cutting structure arrangements the arrangement must provide efficient penetration of

the formation to be drilled with accurate cut gauge. The gauge of the hole drilled is maintained by the outside cutters which are also known as gauge cutters. Teeth are vulnerable to wear and that increases in abrasive sandstone formations. When the gauge cutters are worn out, the consequent hole drilled is undergauge. The cones rotate at the bottom of the hole and drill hole predominanatly with a grinding and chipping action. The teeth are pressed onto the formation below the bit and applies a force exceeding the compressive strength of the rock

Hydraulic arrangements they must be designed so as to efficiently remove and

evacuate all cuttings from the bottom hole.

Page 15: Drilling Engineering - Drill Bit

Drill Bit Classification Drill bits are classified by IADC (International

Association of Drilling Contractor) to identify similar bit types made from different manufacturers.

Drag bit classification – it consists of four digits. First Digit – an alphabet. It defines the type of cutter

and the body material.○ D: natural diamond matrix body○ M: matrix body PDC○ S: steel body PDC○ T: matrix body TSP○ O: others

Page 16: Drilling Engineering - Drill Bit

Second Digit – numbers 1 to 9 define bit profile. G denotes gauge height and C denotes cone height.○ 1: G high, C high○ 2: G high, C medium○ 3: G high, C low○ 4: G medium, C high○ 5: G medium, C medium○ 6: G medium, C low○ 7: G low, C high○ 8: G low, C medium○ 9: G low, C low

Third Digit – numbers 1 to 9 define hydraulic design.○ a: fluid exit (changeable jets, fixed ports, open throat)○ b: cutter distribution (bladed, ribbed, open-faced)

Page 17: Drilling Engineering - Drill Bit

○ 1: changeable jets, bladed○ 2: fixed ports, bladed○ 3: open throat, bladed○ 4: changeable jets, ribbed○ 5: fixed ports, ribbed○ 6: open throat, ribbed○ 7: changeable jets, open-faced○ 8: fixed ports, open-faced○ 9: open throat, open-faced

Fourth Digit – numbers 0 to 9 denote cutter size and density.○ 0: impregnated○ 1: density light, size large○ 2: density medium, size large○ 3: density heavy, size large

Page 18: Drilling Engineering - Drill Bit

○ 4: density light, size medium○ 5: density medium, size medium○ 6: density heavy, size medium○ 7: density light, size small○ 8: density medium, size small○ 9: density heavy, size small

Roller bit classification – consists of four digits. First Digit – numbers 1, 2, and 3 designate steel-milled

tooth bits and correspond to increasing formation hardness.○ 1: soft formation with low UCS and high drillability○ 2: medium to medium-hard formations with high UCS○ 3: hard semi-abrasive and abrasive formations

Page 19: Drilling Engineering - Drill Bit

Numbers 4, 5, 6, 7 and 8 designate tungsten carbide insert bits and correspond to increasing formation hardness.○ 4: soft formation with low UCS and high drillability○ 5: soft to medium-hard formations with low UCS○ 6: medium-hard formations with high UCS○ 7: hard semi-abrasive and abrasive formations○ 8: extremely hard and abrasive formations

Second Digit – numbers 1, 2, 3 and 4 denote a sub-classification of the formation hardness in each of the eight classes determined by the first digit. Number 1 depicts softess formation in a series and number 4 depicts hardess formation in a series.

Page 20: Drilling Engineering - Drill Bit

*** UCS = Uniaxial unconfined compressive strength

Third Digit – defines the type of bearing and specifies the presence/absence of gauge protection by tungsten carbide inserts.○ 1: standard roller bearing (non-sealed)○ 2: roller bearing, air cooled○ 3: roller bearing, gauge protected○ 4: sealed roller bearing

Hardness UCS (psi) Formation TypesUltra soft <1,000 Gumbo, clayVery soft 1,000 – 4,000 Unconsolidated sands, chalk, salt, claystoneSoft 4,000 – 8,000 Coal, siltstone, schist, sandsMedium 8,000 – 17,000 Sandstone, slate, shale, limestone, dolomiteHard 17,000 – 27,000 Quartzite, basalt, gabbro, limestone, dolomiteVery hard >27,000 Marble, granite, gneiss

Page 21: Drilling Engineering - Drill Bit

○ 5: sealed roller bearing, gauge protected○ 6: sealed friction bearing○ 7: sealed friction bearing, gauge protected

Fourth Digit – provides in general information about the bit characteristics.○ A: air application, journal bearing bits with air circulation

nozzles○ B: special bearing seal, application at high RPM○ C: center jet○ D: deviation control○ E: extended jets○ G: extra gauge/body protection○ H: horizontal/steering application○ J: jet deflection

Page 22: Drilling Engineering - Drill Bit

○ L: lug pads, pads very close to gauge diameter○ M: motor application, special design for use on downhole

motors○ S: standard steel tooth model○ T: two-cone bits, sometimes used for deviation control and

penetration rate○ W: enhanced cutting structure○ X: chisel tooth insert○ Y: conical tooth insert○ Z: other insert shape

Page 23: Drilling Engineering - Drill Bit

Examples

135MSoft formation milled tooth bit; roller bearings with gauge protection; motor application

Page 24: Drilling Engineering - Drill Bit

447XSoft formation insert bit; friction bearings with gauge protection; chisel inserts

Page 25: Drilling Engineering - Drill Bit

637YMedium-hard insert bit; friction bearings with gauge protection; conical inserts

Page 26: Drilling Engineering - Drill Bit

Drill Bit Grading Dull drill bits are graded after runs according to

tooth wear/loss, worn bearings, and gauge wear.

Tooth Wear/Loss – the reduction of tooth height.It reported in the nearest eighth, thus a bit which teeth are worn out to half of its original height is 4/8 and reported as T-4. Normally, the tooth wear of a bit is not evenly distributed, some are worn more than others, some are broken out, BT; some are chipped (insert bits), CT; some are lost (insert bits), LT.

Page 27: Drilling Engineering - Drill Bit

BT

LT CT

BT

Page 28: Drilling Engineering - Drill Bit

Bearing Wear – bearing wear in the field is difficult since the bit would need to be disassembled for inspection. Often the bearing wear is reported based on the total bit running hours. Thus, a bit expected to have a rotation time of 40 hours but rotated at bottom for 10 hours, would bearing wear is reported as B-2, i.e. 10 hours 840 hours

×

Page 29: Drilling Engineering - Drill Bit

Gauge Wear – when the gauge teeth of a bit are worn, the drilled hole will be under-gauged which may lead to damage of the next bit. A ring gauge is used to measure the wear. The loss of diameter in inches is reported as the nearest eighth. A bit which diameter is reduced by 0.5 in. is reported as G-O-4, (i.e. 0.5 x 8). Letter O is for “out-of-gauge” and letter I is for “in-gauge.”

Page 30: Drilling Engineering - Drill Bit

Cracked cone

Lost cone

Page 31: Drilling Engineering - Drill Bit

Balled-up bit

Washed-out bit