www.hytera.com
Respond & Achieve
Hytera Patrol System Tutorial
04Software Installation03
SystemConfig
01System Overview
02NetworkStructure
01System
Overview
System Overview
Receiving Station: A repeater (RD62X/RD96X/RD98X/RD98XS) or a mobile radio (only MD78X) can work as a patrol data receiving station.
System ComponentsItem Power Supply Working
TemperatureFrequency Valid
Distance
Patroller ID Card No extra power supply
-22~55℃ 13.56~14.2Mhz 3 cm
Patrol Checkpoint No extra power supply
-40~85 ℃ 13.56~14.2Mhz 4 cm
UHF: 400-470Mhz 4W(High); 1W(Low)
VHF: 136-174Mhz 5W(High); 1W(Low)
16 Hours (1500mAh); 22 Hours (2000mAh)
U.S.A Military Standard & IP54
Analog & Digital auto detect
Embedded RFIDUp to 250 pieces of offline data could be stored
PD41XPatrol Radio
02NetworkStructure
Single Site Solution
Multi-sites Solution
03System Config
Mobile Receiving Station ConfigForward To PC
Step 1 Go to “Conventional -> General Setting -> Network” from the left navigation tree of CPS.
Step 2 Select Forward To PC in Radio to PC Network interface.
Mobile Receiving Station ConfigChannel Configuration
Step 1 Go to “Conventional -> Channel -> Digital Channel” from the left navigation tree of CPS,right click Digital Channel and select Add to add a new digital channel.
Step 2 Double-click the new digital channel to enter the configuration interface. Configure the channel alias per configuration planning and select a slot (etc. Slot1) in Slot Operation.
Mobile Receiving Station ConfigChannel Configuration (Continued)
Set the Receive Frequency and Transmit Frequency.
Channel Configuration (with Pseudo Trunk feature)
If Mobile Radio Receiving Station Solution uses only one frequency, the Pseudo Trunk feature must be enabled; the slot for patrolling services must be different from the slot for voice communication; RX Group List and TX Contact must be set to None.
Mobile Receiving Station Config
Mobile Receiving Station ConfigRadio ID
Go to “Conventional -> DMR Services -> Basic” or “Conventional -> Digital Common -> Basic” to set the Radio ID of the Mobile Radio Receiving Station.
Mobile Receiving Station ConfigTMS Port
Go to “Conventional -> General Setting -> Network -> Radio Services” and set “TMS Port” to “5016”.
Repeater ConfigurationSingle site Network
Step 1 Go to “Conventional -> General Setting -> Network” from the left navigation tree of CPS and configure the following parameters.
Repeater ConfigurationSingle site Network (Continued)
Step 2 Select “Single Site” for local operation
Step 3 Click “Forward to PC”
Step 4 Enter the client computer IP address into “Third Party Server IP”.
Step 1 Go to “Conventional -> General Setting -> Network” from the left navigation tree of CPS and configure the following parameters.”.
Repeater ConfigurationMulti-sites IP Connection (Master)
Repeater ConfigurationMulti-sites IP Connection (Master)
Step 2 Select “Master”. The repeater will operate locally; it will not send data to other repeaters; patrol data will be uploaded to the client.
Step 1 Set repeater IP address into the same LAN of Third Party Server IP.
Multi-sites IP Connection (Slave)
Repeater Configuration
Step 2 Select “Slave”. The repeater will send patrol data to “Master” via Ethernet.
Multi-sites IP Connection (Slave)
Repeater Configuration
Notice: Unclick “Forward to PC” box of “Slave” repeater.
Repeater ConfigurationChannel Configuration
Step 1 Go to “Conventional -> Channel -> Digital Channel” from the left navigation tree of CPS,right click Digital Channel and select Add to add a new digital channel.
Step 2 Double-click the new digital channel to enter the configuration interface. Configure the channel alias per configuration planning and select a slot (etc. Slot1) in Slot Operation..
Repeater ConfigurationChannel Configuration (Continued)
Notice:If the voice service and patrolling service shares the same frequency, different slots must be used. For example, the patrolling service uses slot 1 while the voice service uses slot 2
Step 3 Go to “Conventional -> Zone” from the left navigation tree of the CPS, select the “Digital patrol channel” and click “Add” to add it to the last channel in “Member” list.
Repeater ConfigurationChannel Configuration (Continued)
Repeater ConfigurationRadio ID
Go to “Conventional -> DMR Services -> Basic” or “Conventional -> Digital Common -> Basic” to set the Radio ID of the Mobile Radio Receiving Station.
Go to “Conventional -> DMR Services -> Contact” from the left navigation tree of the CPS, add the Alias and ID of the repeater or Mobile Radio Receiving Station into the list and set the Call Type to Private Call.
Portable Radio ConfigurationRadio Contact
Portable Radio Configuration
Step 1 The necessary parameters need to configure including: “Slot Operation”, “Receive Frequency”, “Transmit Frequency” and “Tx Contact Name” . The Tx admit of patrolling service channel should be set to “Channel Free”; “TDMA Direct Mode” must be selected.
Channel Configuration
Step 2 Go to “Zone -> Zone 1” from the left navigation tree of the CPS, select the Digital patrol channel and click “Add” to add it to the last channel in Zone 1.
Portable Radio ConfigurationChannel Configuration (Continued)
Notice:For Patrol Management System, the patrolling data of patrol portable radios are automatically switched and transmitted in the last digital channel of the current zone by default. Otherwise, the patrolling data cannot be uploaded successfully
Go to “General Setting -> Buttons” from the left navigation tree of the CPS, select Patrol Emergency from the drop down list for SK1 or SK2
Portable Radio ConfigurationPatrol Emergency
In case of emergency during patrolling, the patroller can press the programmed Patrol Emergency key to trigger the emergency alarm.
Go to “General Setting -> Buttons” from the left navigation tree of the CPS, select Patrol Resend from the drop down list for SK1 or SK2.
Portable Radio ConfigurationPatrol Resend
In case of patrol data uploading failure during patrolling, the patroller can press the programmed Patrol Resend key to resend the data.
04Software
Installation
Hardware Devices Requirements
Software Installation
Downloading and Unzipping Installation Package
1. Download “Hytera PD41X Patrol Management System.rar” from www.hytera.com (Download path: Downloads -> Driver & Software -> PD41X).
2. Unzipping the installation package into a chosen folder.