Tungsten Carbide (TC) Tips for High-Pressure Spraying
Spray Nozzles
Spray Control
Spray Analysis
Spray Fabrication
2 1.800.95.SPRAY | Intl. 1.630.665.5000 | www.spray.com
Tungsten Carbide Tips Save Water, Chemicals and ElectricityIn high-pressure spraying applications, the high velocity of the liquid through the nozzle causes the orifice to wear very quickly. As the orifice becomes larger, the flow rate will increase. Surprisingly, tens and even hundreds of thousands of dollars can be wasted in excess water and chemicals as a result of nozzle wear. Electricity costs will also rise due to excess pump operation.
Using spray tips constructed of a harder material may provide significantly longer wear life. The Abrasion Resistance Ratio chart below shows that tungsten carbide has a resistance ratio up to 250 times greater than brass.
Approximate Abrasion Resistance Ratios
Spray Nozzle Material Resistance Ratio
Aluminum 1
Brass 1
Polypropylene 1 - 2
Steel 1.5 - 2
Monel® 2 - 3
Stainless Steel 4 - 6
Hastelloy® 4 - 6
Hardened Stainless Steel 10 - 15
Stellite® 10 - 15
Silicon Carbide (Nitride Bonded)
90 - 130
Ceramics 90 - 200
Carbides 180 - 250
Synthetic ruby or sapphire 600 - 2000
Monel® is a registered trademark of Special Metals Corporation.Hastelloy® is a registered trademark of Haynes International, Inc.Stellite® is a registered trademark of Deloro Stellite.
31.800.95.SPRAY | Intl. 1.630.665.5000 | www.spray.com
TC TipS Overview
Model Max. Pressure Spray Pattern Typical Applications Page
Fine Spray TC Tips
2000 psi (138 bar)
Hollow cone
• Humidification
• Coating inside piping
• Evaporative cooling
4
High-Pressure TC Tips
3000 psi (207 bar)
Flat spray• Paint spraying
• Sealant/protective coating spraying5
Heavy Edge TC Tips
4000 psi (276 bar)
Flat spray • Road paint striping 9
Robotic TC Tips
4000 psi (276 bar)
Flat spray• Robotic spraying
• Sealant/coating spraying11
ECRTC Tips4000 psi (276 bar)
Even flat spray
• Viscous solution spraying such as thickened paints and adhesives
• High particulate solution spraying
14
RotoClean® Airless Spray Nozzles
5000 psi (345 bar)
Flat spray• Manual spraying
• High-pressure paint spraying16
High-Pressure 11430 UniJet® Body
3000 psi (207 bar)
Flat spray• Nozzle body for high pressure
UniJet spray tips20
Model HV Orifice2000 psi (138 bar)
Flat spray• Orifice insert produces a fine finish;
for use with high-pressure TC tips20
4 1.800.95.SPRAY | Intl. 1.630.665.5000 | www.spray.com
Fine Spray TC TipsBenefits
• Ideal for humidification, coating inside piping and evaporative cooling
• Very small drop size
• Hydraulic atomization – no compressed air required
Specifications
Maximum pressure: 2000 psi (138 bar)
Spray pattern: Hollow cone
Materials: 303 stainless steel with tungsten carbide orifice
Ordering Information
A B Net Weight
.593" .625" .42 oz
Dimensions & Weights
Capacity Size
Equiv. Orifice
Dia.
Capacity* (gallons per minute) Approx.** Spray Pattern
Diameter (at 1'
distance)
400 psi
750 psi
1000 psi
1500 psi
2000 psi
.60 .016" .032 .043 .050 .061 .072 3"
.80 .0135" .042 .058 .067 .082 .095 3"
.90 .016" .047 .065 .075 .092 .11 3"
1 .020" .053 .072 .083 .10 .12 3-1/2"
1.5 .020" .080 .11 .13 .15 .18 3-1/2"
1.8 .025" .094 .13 .15 .18 .22 4-1/2"
2 .028" .11 .14 .17 .21 .24 4-1/2"
3 .028" .16 .22 .25 .31 .35 6"
4 .042" .21 .29 .33 .41 .47 8"
6 .042" .32 .43 .50 .61 .71 10"
8 .060" .42 .58 .67 .82 .94 12"
9 .060" .47 .65 .75 .92 1.1 14"
10 .064" .53 .72 .83 1.0 1.2 16"
12 .076" .63 .87 1.0 1.2 1.4 18"
14 .076" .74 1.0 1.2 1.4 1.6 14"
15 .081" .79 1.1 1.25 1.5 1.7 16"
16 .086" .84 1.2 1.3 1.6 1.9 18"
18 .076" .95 1.3 1.5 1.8 2.1 16"
20 .081" 1.1 1.4 1.7 2.1 2.4 18"
22 .076" 1.2 1.6 1.8 2.3 2.6 12"
24 .081" 1.3 1.7 2.0 2.5 2.8 13"
26 .086" 1.4 1.9 2.2 2.7 3.1 14"
Fine Spray TC Tips Performance Data
* Tabulated capacities based on water.** Spray pattern diameter is based on liquid with viscosity of 20 seconds, #4 Zahn Cup
spraying at 1600 psi (110 bar). Coverage will vary with viscosities and pressures.
Fine Spray TC Tip
B
A
T N — S S T C 1 0 | | | Tip Material Capacity Type Code Size
TN-SSTC Spray Tip
Based on largest/heaviest version of each type.
51.800.95.SPRAY | Intl. 1.630.665.5000 | www.spray.com
High-Pressure TC TipsBenefits
• Ideal for paint spraying and the application of sealants and protective coatings in automotive manufacturing
• Erosion-resistant tungsten carbide orifice insert provides longer wear life than standard stainless steel tips
• Excellent corrosion resistance
• High-impact flat spray pattern with tapered edges provides even coverage when sprays overlap
• Tip orifice insert is recessed in a solid stainless steel tip body to protect against damage
Specifications
Maximum pressure: 3000 psi (207 bar)
Spray pattern: Flat spray
Materials: Stainless steel with tungsten carbide orifice insert
High-Pressure 11430 UniJet® Body with
High-Pressure TC Tip
Spray Angle
at 40 psi
Spray Tip Number
Equiv. Orifice
Dia.
Capacity* (gallons per minute)
Approx.** Spray
Pattern Width (at 1’
distance)
500 psi
1000 psi
1500 psi
2000 psi
3000 psi
110°
1100017-TC .011" .06 .09 .10 .12 .15 15-1/2"
1100025-TC .013" .09 .12 .15 .18 .22 16-1/2"
1100033-TC .015" .12 .16 .20 .23 .29 17"
1100039-TC .016" .14 .20 .24 .28 .34 18"
1100050-TC .018" .18 .25 .30 .36 .44 19"
1100067-TC .021" .24 .33 .41 .47 .59 21"
1100080-TC .023" .28 .40 .49 .57 .69 22"
11001-TC .026" .35 .50 .61 .72 .86 23"
110015-TC .031" .53 .75 .91 1.1 1.3 25"
11002-TC .036" .71 1.0 1.2 1.4 1.7 26"
11003-TC .043" 1.1 1.5 1.8 2.1 2.7 27"
Spray Angle
at 40 psi
Spray Tip Number
Equiv. Orifice
Dia.
Capacity* (gallons per minute)
Approx.** Spray
Pattern Width (at 1’
distance)
500 psi
1000 psi
1500 psi
2000 psi
3000 psi
110°
11004-TC .052" 1.4 2.0 2.5 2.8 3.4 28"
11005-TC .057" 1.8 2.5 3.1 3.5 4.4 28"
110053-TC .058" 1.9 2.7 3.2 3.7 4.7 28"
11006-TC .062" 2.1 3.0 3.7 4.2 5.1 28"
11007-TC .067" 2.5 3.5 4.3 5.0 6.1 28"
11008-TC .072" 2.8 4.0 4.9 5.7 6.9 28"
11009-TC .076" 3.2 4.5 5.5 6.4 7.8 28"
11010-TC .078" 3.5 5.0 6.1 7.1 8.6 28"
11011-TC .083" 3.9 5.5 6.7 7.8 9.6 28"
11012-TC .089" 4.3 6.0 7.4 8.5 10.5 28"
95° 950017-TC .011" .06 .08 .10 .12 .15 13"
High-Pressure TC Tips Performance Data
* Tabulated capacities based on water. ** Spray pattern width is based on liquid with viscosity of 20 seconds, #4 Zahn Cup spraying at 1600 psi (110 bar). Coverage will vary with viscosities and pressures.
High-Pressure TC Tip
6 1.800.95.SPRAY | Intl. 1.630.665.5000 | www.spray.com
Spray Angle
at 40 psi
Spray Tip Number
Equiv. Orifice
Dia.
Capacity* (gallons per minute)
Approx.** Spray
Pattern Width (at 1’
distance)
500 psi
1000 psi
1500 psi
2000 psi
3000 psi
95°
950025-TC .013" .09 .12 .15 .18 .22 14"
950033-TC .015" .12 .16 .20 .23 .29 15"
950039-TC .016" .14 .20 .24 .28 .34 16"
950044-TC .017" .16 .22 .27 .31 .39 16"
950050-TC .018" .18 .25 .30 .36 .44 17"
950067-TC .021" .24 .33 .41 .47 .59 19"
950080-TC .023" .28 .40 .49 .57 .69 19"
9501-TC .026" .35 .50 .61 .72 .86 21"
95015-TC .031" .53 .75 .91 1.1 1.3 21"
9502-TC .036" .71 1.0 1.2 1.4 1.7 22"
9503-TC .043" 1.1 1.5 1.8 2.1 2.7 22"
9504-TC .052" 1.4 2.0 2.5 2.8 3.4 23"
9505-TC .057" 1.8 2.5 3.1 3.5 4.4 23"
9506-TC .062" 2.1 3.0 3.7 4.2 5.1 23"
9507-TC .067" 2.5 3.5 4.3 5.0 6.1 23"
9508-TC .072" 2.8 4.0 4.9 5.7 6.9 23"
9509-TC .076" 3.2 4.5 5.5 6.4 7.8 23"
9510-TC .078" 3.5 5.0 6.1 7.1 8.6 23"
9511-TC .085" 3.9 5.5 6.7 7.8 9.6 23"
9512-TC .089" 4.3 6.0 7.4 8.5 10.5 23"
9513-TC .092" 4.6 6.5 8.0 9.2 11.3 23"
9514-TC .095" 4.9 7.0 8.6 9.9 12.0 23"
9515-TC .099" 5.3 7.5 9.2 10.6 13.0 23"
9516-TC .100" 5.7 8.0 9.8 11.3 14.0 23"
9518-TC .104" 6.4 9.0 11.0 12.7 15.7 23"
9520-TC .109" 7.1 10.0 12.2 14.1 17.4 23"
80°
800011-TC .009" .04 .06 .07 .08 .10 10-1/2"
800017-TC .011" .06 .08 .10 .12 .15 11-1/2"
800025-TC .013" .09 .12 .15 .18 .22 12-1/2"
800033-TC .015" .12 .16 .20 .23 .29 13"
800039-TC .016" .14 .20 .24 .28 .34 14"
800050-TC .018" .18 .25 .30 .36 .44 15"
800067-TC .021" .24 .33 .41 .47 .59 17"
800080-TC .023" .28 .40 .49 .57 .69 17"
8001-TC .026" .35 .50 .61 .72 .86 19"
80015-TC .031" .53 .75 .91 1.1 1.3 19"
8002-TC .036" .71 1.0 1.2 1.4 1.7 19"
8003-TC .043" 1.1 1.5 1.8 2.1 2.7 19"
8004-TC .052" 1.4 2.0 2.5 2.8 3.4 19"
8005-TC .057" 1.8 2.5 3.1 3.5 4.4 19"
8006-TC .062" 2.1 3.0 3.7 4.2 5.1 19"
8007-TC .067" 2.5 3.5 4.3 5.0 6.1 19"
Spray Angle
at 40 psi
Spray Tip Number
Equiv. Orifice
Dia.
Capacity* (gallons per minute)
Approx.** Spray
Pattern Width (at 1’
distance)
500 psi
1000 psi
1500 psi
2000 psi
3000 psi
80°
8008-TC .072" 2.8 4.0 4.9 5.7 6.9 19"
8009-TC .076" 3.2 4.5 5.5 6.4 7.8 19"
8010-TC .078" 3.5 5.0 6.1 7.1 8.6 19"
8011-TC .085" 3.9 5.5 6.7 7.8 9.6 19"
8012-TC .089" 4.3 6.0 7.4 8.5 10.5 19"
8013-TC .093" 4.6 6.5 8.0 9.2 11.3 19"
8014-TC .096" 4.9 7.0 8.6 9.9 12.0 19"
8015-TC .099" 5.3 7.5 9.2 10.6 13.0 19"
73°
730023-TC .012" .08 .11 .14 .16 .20 11-1/2"
730039-TC .016" .14 .20 .24 .28 .34 13"
730044-TC .017" .17 .22 .27 .31 .42 13"
730050-TC .018" .18 .25 .31 .35 .44 13"
730154-TC .031" .54 .77 .94 1.1 1.3 13"
65°
650008-TC .007" .03 .04 .05 .06 .07 8-1/2"
650011-TC .009" .04 .06 .07 .08 .10 9-1/4"
650017-TC .011" .06 .08 .10 .12 .15 10"
650025-TC .013" .09 .12 .15 .18 .22 10-1/2"
650033-TC .015" .12 .16 .20 .23 .29 11"
650039-TC .016" .14 .20 .24 .28 .34 12"
650044-TC .017" .16 .22 .27 .31 .39 12-1/2"
650050-TC .018" .18 .25 .30 .36 .44 13"
650055-TC .019" .19 .28 .34 .39 .47 13"
650067-TC .021" .24 .33 .41 .47 .59 15"
650080-TC .023" .28 .40 .49 .57 .69 15"
6501-TC .026" .35 .50 .61 .72 .86 16"
65015-TC .031" .53 .75 .91 1.1 1.3 16"
6502-TC .036" .71 1.0 1.2 1.4 1.7 16"
6503-TC .043" 1.1 1.5 1.8 2.1 2.7 16"
6504-TC .052" 1.4 2.0 2.5 2.8 3.4 16"
6505-TC .057" 1.8 2.5 3.1 3.5 4.4 16"
6506-TC .062" 2.1 3.0 3.7 4.2 5.1 16"
6507-TC .067" 2.5 3.5 4.3 5.0 6.1 16"
6508-TC .072" 2.8 4.0 4.9 5.7 6.9 16"
6509-TC .076" 3.2 4.5 5.5 6.4 7.8 16"
6510-TC .078" 3.5 5.0 6.1 7.1 8.6 16"
6511-TC .085" 3.9 5.5 6.7 7.8 9.6 16"
6512-TC .089" 4.3 6.0 7.4 8.5 10.5 16"
6513-TC .093" 4.6 6.5 8.0 9.2 11.3 16"
6514-TC .096" 4.9 7.0 8.6 9.9 12.0 16"
6515-TC .099" 5.3 7.5 9.2 10.6 13.0 16"
6517-TC .102" 6.0 8.5 10.4 12.0 14.7 16"
6520-TC .109" 7.1 10.0 12.2 14.1 17.4 16"
* Tabulated capacities based on water.** Spray pattern diameter is based on liquid with viscosity of 20 seconds, #4 Zahn Cup spraying at 1600 psi (110 bar). Coverage will vary with viscosities and pressures.
High-Pressure TC Tips Performance Data
71.800.95.SPRAY | Intl. 1.630.665.5000 | www.spray.com
Spray Angle
at 40 psi
Spray Tip Number
Equiv. Orifice
Dia.
Capacity* (gallons per minute)
Approx.** Spray
Pattern Width (at 1’
distance)
500 psi
1000 psi
1500 psi
2000 psi
3000 psi
50°
500004-TC .005" .01 .02 .02 .03 .03 6-1/2"
500006-TC .006" .02 .03 .04 .04 .05 7"
500008-TC .007" .03 .04 .05 .06 .07 7-3/4"
500011-TC .009" .04 .06 .07 .08 .10 8"
500017-TC .011" .06 .08 .10 .12 .15 8-1/2"
500025-TC .013" .09 .12 .15 .18 .22 9"
500033-TC .015" .12 .16 .20 .23 .29 10"
500039-TC .016" .14 .20 .24 .28 .34 10-1/2"
500044-TC .017" .16 .22 .27 .31 .39 10-1/2"
500050-TC .018" .18 .25 .30 .36 .44 11"
500055-TC .019" .19 .28 .34 .39 .47 11"
500067-TC .021" .24 .33 .41 .47 .59 12"
500080-TC .023" .28 .40 .49 .57 .69 13"
5001-TC .026" .35 .50 .61 .72 .86 14"
50015-TC .031" .53 .75 .91 1.1 1.3 14"
5002-TC .036" .71 1.0 1.2 1.4 1.7 14"
5003-TC .043" 1.1 1.5 1.8 2.1 2.7 14"
5004-TC .052" 1.4 2.0 2.5 2.8 3.4 14"
5005-TC .057" 1.8 2.5 3.1 3.5 4.4 14"
5006-TC .062" 2.1 3.0 3.7 4.2 5.1 14"
5007-TC .067" 2.5 3.5 4.3 5.0 6.1 14"
5008-TC .072" 2.8 4.0 4.9 5.7 6.9 14"
5010-TC .078" 3.5 5.0 6.1 7.1 8.6 14"
5015-TC .099" 5.3 7.5 9.2 10.6 13.0 14"
40°
400004-TC .005" .01 .02 .03 .03 .03 6-1/2"
400006-TC .006" .02 .03 .04 .04 .05 6-1/2"
400008-TC .007" .03 .04 .05 .06 .07 6-1/2"
400011-TC .009" .04 .06 .07 .08 .10 7"
400017-TC .011" .06 .08 .10 .12 .15 7-1/2"
400025-TC .013" .09 .12 .15 .18 .22 8"
400033-TC .015" .12 .16 .20 .23 .29 8-1/2"
400039-TC .016" .14 .20 .24 .28 .34 9"
400044-TC .017" .16 .22 .27 .31 .39 9-1/2"
400050-TC .018" .18 .25 .30 .36 .44 10"
400055-TC .019" .19 .28 .34 .39 .47 10"
400067-TC .021" .24 .33 .41 .47 .59 11"
400080-TC .023" .28 .40 .49 .57 .69 11"
4001-TC .026" .35 .50 .61 .72 .86 12"
40013-TC .029" .46 .65 .80 .92 1.1 12"
40015-TC .031" .53 .75 .91 1.1 1.3 12"
4002-TC .036" .71 1.0 1.2 1.4 1.7 12"
4003-TC .043" 1.1 1.5 1.8 2.1 2.7 12"
Spray Angle
at 40 psi
Spray Tip Number
Equiv. Orifice
Dia.
Capacity* (gallons per minute)
Approx.** Spray
Pattern Width (at 1’
distance)
500 psi
1000 psi
1500 psi
2000 psi
3000 psi
40°
4004-TC .052" 1.4 2.0 2.5 2.8 3.4 12"
4005-TC .057" 1.8 2.5 3.1 3.5 4.4 12"
4006-TC .062" 2.1 3.0 3.7 4.2 5.1 12"
4007-TC .067" 2.5 3.5 4.3 5.0 6.1 12"
4008-TC .072" 2.8 4.0 4.9 5.7 6.9 12"
4009-TC .076" 3.2 4.5 5.5 6.4 7.8 12"
4010-TC .078" 3.5 5.0 6.1 7.1 8.6 12"
4011-TC .083" 3.9 5.5 6.7 7.8 9.6 12"
4015-TC .099" 5.3 7.5 9.2 10.6 13.0 12"
25°
250004-TC .005" .01 .02 .03 .03 .03 5"
250006-TC .006" .02 .03 .04 .04 .05 5"
250008-TC .007" .03 .04 .05 .06 .07 5-1/2"
250011-TC .009" .04 .06 .07 .08 .10 5-1/2"
250017-TC .011" .06 .08 .10 .12 .15 6"
250025-TC .013" .09 .12 .15 .18 .22 6"
250033-TC .015" .12 .16 .20 .23 .29 7"
250039-TC .016" .14 .20 .24 .28 .34 7"
250050-TC .018" .18 .25 .30 .36 .44 7"
250055-TC .019" .19 .28 .34 .39 .47 7"
250067-TC .021" .24 .33 .41 .47 .59 8"
250080-TC .023" .28 .40 .49 .57 .69 8-1/2"
2501-TC .026" .35 .50 .61 .72 .86 9"
25015-TC .031" .53 .75 .91 1.1 1.3 9"
2502-TC .036" .71 1.0 1.2 1.4 1.7 9"
2503-TC .043" 1.1 1.5 1.8 2.1 2.7 9"
2504-TC .052" 1.4 2.0 2.5 2.8 3.4 9"
2505-TC .057" 1.8 2.5 3.1 3.5 4.4 9"
2506-TC .062" 2.1 3.0 3.7 4.2 5.1 9"
2508-TC .072" 2.8 4.0 4.9 5.7 6.9 9"
2510-TC .078" 3.5 5.0 6.1 7.1 8.6 9"
15°
150004-TC .005" .01 .02 .03 .03 .03 4"
150006-TC .006" .02 .03 .04 .04 .05 4"
150008-TC .007" .03 .04 .05 .06 .07 4-1/2"
150011-TC .009" .04 .06 .07 .08 .10 4-1/2"
150017-TC .011" .06 .08 .10 .12 .15 5"
150025-TC .013" .09 .12 .15 .18 .22 5"
150033-TC .015" .12 .16 .20 .23 .29 5-1/2"
150039-TC .016" .14 .20 .24 .28 .34 6"
150044-TC .017" .16 .22 .27 .31 .39 6"
150050-TC .018" .18 .25 .30 .36 .44 6"
150067-TC .021" .24 .33 .41 .47 .59 6-1/2"
150080-TC .023" .28 .40 .49 .57 .69 7"
* Tabulated capacities based on water.** Spray pattern diameter is based on liquid with viscosity of 20 seconds, #4 Zahn Cup spraying at 1600 psi (110 bar). Coverage will vary with viscosities and pressures.
High-Pressure TC Tips Performance Data
8 1.800.95.SPRAY | Intl. 1.630.665.5000 | www.spray.com
Spray Angle
at 40 psi
Spray Tip Number
Equiv. Orifice
Dia.
Capacity* (gallons per minute)
Approx.** Spray
Pattern Width (at 1’
distance)
500 psi
1000 psi
1500 psi
2000 psi
3000 psi
15°
1501-TC .026" .35 .50 .61 .72 .86 7"
15015-TC .031" .53 .75 .91 1.1 1.3 7"
1502-TC .036" .71 1.0 1.2 1.4 1.7 7"
1503-TC .043" 1.1 1.5 1.8 2.1 2.7 7"
1504-TC .052" 1.4 2.0 2.5 2.8 3.4 7"
1505-TC .057" 1.8 2.5 3.1 3.5 4.4 7"
1506-TC .062" 2.1 3.0 3.7 4.2 5.1 7"
1507-TC .067" 2.5 3.5 4.3 4.9 6.1 7"
1508-TC .072" 2.8 4.0 4.9 5.7 6.9 7"
1510-TC .078" 3.5 5.0 6.1 7.1 8.6 7"
1515-TC .099" 5.3 7.5 9.2 10.6 13.0 7"
10°
100004-TC .005" .01 .02 .03 .03 .03 3"
100006-TC .006" .02 .03 .04 .04 .05 3"
100008-TC .007" .03 .04 .05 .06 .07 3-1/2"
100011-TC .009" .04 .06 .07 .08 .10 3-1/2"
100017-TC .011" .06 .08 .10 .12 .15 4"
100025-TC .013" .09 .12 .15 .18 .22 4"
100033-TC .015" .12 .16 .20 .23 .29 4-1/2"
100039-TC .016" .14 .20 .24 .28 .34 5"
* Tabulated capacities based on water.** Spray pattern diameter is based on liquid with viscosity of 20 seconds, #4 Zahn Cup spraying at 1600 psi (110 bar). Coverage will vary with viscosities and pressures.
High-Pressure TC Tips Performance Data
Spray Angle
at 40 psi
Spray Tip Number
Equiv. Orifice
Dia.
Capacity* (gallons per minute)
Approx.** Spray
Pattern Width (at 1’
distance)
500 psi
1000 psi
1500 psi
2000 psi
3000 psi
10°
100050-TC .018" .18 .25 .30 .36 .44 5"
100067-TC .021" .24 .33 .41 .47 .59 5-1/2"
100080-TC .023" .28 .40 .49 .57 .69 5-1/2"
1001-TC .026" .35 .50 .61 .72 .86 6"
10015-TC .031" .53 .75 .91 1.1 1.3 6"
1002-TC .036" .71 1.0 1.2 1.4 1.7 6"
5°
050004-TC .005" .01 .02 .03 .03 .03 2-1/2"
050008-TC .007" .03 .04 .05 .06 .07 2-1/2"
050011-TC .009" .04 .06 .07 .08 .10 2-1/2"
050017-TC .011" .06 .08 .10 .12 .15 3"
050025-TC .013" .09 .12 .15 .18 .22 3"
050033-TC .015" .12 .16 .20 .23 .29 3-1/2"
050039-TC .016" .14 .20 .24 .28 .34 4"
050050-TC .018" .18 .25 .30 .36 .44 4"
050067-TC .021" .24 .33 .41 .47 .59 4"
0501-TC .026" .35 .50 .61 .72 .86 4"
05015-TC .031" .53 .75 .91 1.1 1.3 4"
0502-TC .036" .71 1.0 1.2 1.4 1.7 4"
0503-TC .043" 1.1 1.5 1.8 2.1 2.7 4"
Based on largest/heaviest version of each type.
Dimensions & Weights
T p 1 5 0 4 – T C | | | | Tip Spray Capacity Material Code Angle Size Code
High-pressure TC Spray Tip
Ordering Information
A
B
A B Net Weight
.375" .59" .32 oz
91.800.95.SPRAY | Intl. 1.630.665.5000 | www.spray.com
Heavy Edge TC TipsBenefits
• Ideal for road paint striping
• Heavy edge distribution for defined edge pattern
• Erosion-resistant tungsten carbide orifice insert provides longer wear life than standard stainless steel tips
• Excellent corrosion resistance
• Tip orifice insert is recessed in a solid stainless steel tip body to protect against damage
Specifications
Maximum pressure: 4000 psi (276 bar)
Spray pattern: Flat spray
Materials: Stainless steel with tungsten carbide orifice insert
Heavy Edge TC Tips Performance Data
Heavy Edge TC Tip
Nozzle Type A B Net
Weight
Small Capacity (up to -025) .375" .593" .32 oz
Large Capacity (-03 and larger) .50" .593" .32 oz
Dimensions & Weights
A
B
Ordering Information
4 0 0 5 H e – T C | | | | Spray Capacity Tip Material Angle Size Code Code
Heavy edge TC Spray Tip
Spray Angle
at 40 psi
Spray Tip Number
Equiv. Orifice
Dia.
Capacity* (gallons per minute)
500 psi
1000 psi
1500 psi
2000 psi
3000 psi
4000 psi
65°
650033HE-TC .015" .12 .16 .20 .23 .29 .34
6507HE-TC .067" 2.5 3.5 4.3 4.9 6.1 7.1
6508HE-TC .072" 2.8 4.0 4.9 5.7 6.9 7.9
50°
500050HE-TC .018" .18 .25 .30 .36 .44 .51
5001HE-TC .026" .35 .50 .61 .72 .86 .99
50015HE-TC .031" .53 .75 .91 1.1 1.3 1.5
5002HE-TC .036" .71 1.0 1.2 1.4 1.7 2.0
50025HE-TC .040" .88 1.3 1.5 1.8 2.2 2.5
5004HE-TC .052" 1.4 2.0 2.5 2.8 3.4 4.0
Based on largest/heaviest version of each type.
*Tabulation is based on water spraying at temperature at 70°F (21°C).
10 1.800.95.SPRAY | Intl. 1.630.665.5000 | www.spray.com
Spray Angle
at 40 psi
Spray Tip Number
Equiv. Orifice
Dia.
Capacity* (gallons per minute)
500 psi
1000 psi
1500 psi
2000 psi
3000 psi
4000 psi
50°
5005HE-TC .057" 1.8 2.5 3.1 3.5 4.4 5.1
5006HE-TC .062" 2.1 3.0 3.7 4.2 5.1 6.0
5007HE-TC .067" 2.5 3.5 4.3 4.9 6.1 7.1
5008HE-TC .072" 2.8 4.0 4.9 5.7 6.9 7.9
5009HE-TC .076" 3.2 4.5 5.5 6.4 7.8 9.1
40°
400033HE-TC .015" .12 .16 .20 .23 .29 .34
4001HE-TC .026" .35 .50 .61 .72 .86 1.5
4002HE-TC .036" .71 1.0 1.2 1.4 1.7 2.0
4003HE-TC .043" 1.1 1.5 1.8 2.1 2.7 3.1
4005HE-TC .057" 1.8 2.5 3.1 3.5 4.4 5.1
4006HE-TC .062" 2.1 3.0 3.7 4.2 5.1 6.0
4007HE-TC .067" 2.5 3.5 4.3 4.9 6.1 7.1
4008HE-TC .072" 2.8 4.0 4.9 5.7 6.9 7.9
4009HE-TC .076" 3.2 4.5 5.5 6.4 7.8 9.1
35° 3506HE-TC .062" 2.1 3.0 3.7 4.2 5.1 6.0
30°
3006HE-TC .062" 2.1 3.0 3.7 4.2 5.1 6.0
3007HE-TC .067" 2.5 3.5 4.3 4.9 6.1 7.1
3008HE-TC .072" 2.8 4.0 4.9 5.7 6.9 7.9
3009HE-TC .076" 3.2 4.5 5.5 6.4 7.8 9.1
25° 250025HE-TC .013" .09 .12 .15 .18 .29 .34
Spray Angle
at 40 psi
Spray Tip Number
Equiv. Orifice
Dia.
Capacity* (gallons per minute)
500 psi
1000 psi
1500 psi
2000 psi
3000 psi
4000 psi
25°
2501HE-TC .026" .35 .50 .61 .72 .86 1.5
25015HE-TC .031" .53 .75 .91 1.1 1.3 1.5
2502HE-TC .036" .71 1.0 1.2 1.4 1.7 2.0
2503HE-TC .043" 1.1 1.5 1.8 2.1 2.7 3.1
2504HE-TC .052" 1.4 2.0 2.5 2.8 3.4 4.0
2505HE-TC .057" 1.8 2.5 3.1 3.5 4.4 5.1
2506HE-TC .062" 2.1 3.0 3.7 4.2 5.1 6.0
2508HE-TC .072" 2.8 4.0 4.9 5.7 6.9 7.9
2510HE-TC .078" 3.5 5.0 6.1 7.1 9.0 9.9
20° 2003HE-TC .043" 1.1 1.5 1.8 2.1 2.7 3.1
15°
150080HE-TC .023" .28 .40 .49 .57 .69 .79
1501HE-TC .026" .35 .50 .61 .72 .86 1.5
15015HE-TC .031" .53 .75 .91 1.1 1.3 1.5
1502HE-TC .036" .71 1.0 1.2 1.4 1.7 2.0
1503HE-TC .043" 1.1 1.5 1.8 2.1 2.7 3.1
1504HE-TC .052" 1.4 2.0 2.5 2.8 3.4 4.0
1505HE-TC .057" 1.8 2.5 3.1 3.5 4.4 5.1
1506HE-TC .062" 2.1 3.0 3.7 4.2 5.1 6.0
1508HE-TC .072" 2.8 4.0 4.9 5.7 6.9 7.9
10° 10025HE-TC .040" .88 1.3 1.5 1.8 2.5 2.5
Heavy Edge TC Tips Performance Data
* Tabulation is based on water spraying at temperature at 70°F (21°C).
111.800.95.SPRAY | Intl. 1.630.665.5000 | www.spray.com
Robotic TC TipsBenefits
• Ideal for use with robotic equipment in precise, repetitive paint spraying applications and operations where overspray is undesirable
• Tips have flats to ensure accurate spray pattern alignment every time
• Tip orifice insert is recessed in a solid stainless steel tip body to protect against damage
• Erosion-resistant tungsten carbide orifice insert provides longer wear life than standard stainless steel tips
• Tighter coverage tolerances than high-pressure TC tips
• Patented flow channel design minimizes heavy spray pattern edges
• CDROBTC tips feature a shorter tip holder than ROBTC tips and are designed for use in applications where the spray solution tends to dry quickly. The tip design helps the solution slide away from the orifice and prevents clogging caused by caking and build-up
Specifications
Maximum pressure: 4000 psi (276 bar)
Spray pattern: Flat spray or solid stream
Materials: Stainless steel body with tungsten carbide orifice
Ordering Information
Nozzle Type A B Locating Flats
Net Weight
TP-ROBTC
.375" .59" 0.5" .32 oz
TP-CDROBTC
.313" .59" 0.5" .32 oz
Dimensions & Weights
ROBTC Tip
CDROBTC Tip
A
B
A
B
T p 4 0 0 1 — r O B T C | | | | Tip Spray Capacity Tip Code Angle Size Type
rOBTC Spray Tip
T p 6 5 0 1 — C D r O B T C | | | | Tip Spray Capacity Tip Code Angle Size Type
CDrOBTC Spray TipBased on largest/heaviest version of each type.
12 1.800.95.SPRAY | Intl. 1.630.665.5000 | www.spray.com
* For solid stream tips, the actual orifice diameter is listed.** Spray pattern width is based on liquid with viscosity of 20 seconds, #4 Zahn Cup spraying at 1600 psi (110 bar). Tabulation is based on spraying water at temperature at 70°F (21°C).
Robotic TC Tips Performance Data
Spray Angle
at 40 psi
Spray Tip Number
Equiv. Orifice Dia. *
Capacity (gallons per minute)Spray Pattern Width
(at 1' Distance)**500 psi
1000 psi
1500 psi
2000 psi
2500 psi
3000 psi
3500 psi
4000 psi
110˚
TP1100067-CDROBTC .021" .24 .33 .41 .47 .53 .58 .63 .67 21" to 22"
TP1100080-CDROBTC .023" .28 .40 .49 .57 .63 .69 .75 .80 21-3/4" to 22-3/4"
TP11001-CDROBTC .026" .35 .50 .61 .72 .79 .87 .94 1.0 23-1/2" to 24-1/2"
TP110015-CDROBTC .031" .53 .75 .91 1.1 1.2 1.3 1.4 1.5 25" to 26"
TP11002-CDROBTC .036" .71 1.0 1.2 1.4 1.6 1.7 1.9 2.0 26" to 27"
95˚TP950080-CDROBTC .023" .28 .40 .49 .57 .63 .69 .75 .80 19-1/2" to 20-1/2"
TP9502-CDROBTC .036" .71 1.0 1.2 1.4 1.6 1.7 1.9 2.0 21-1/2" to 22-1/2"
80˚
TP800044-CDROBTC .017" .16 .22 .27 .31 .35 .38 .41 .44 14-1/2" to 15-1/2"
TP800050-CDROBTC .018" .18 .25 .30 .36 .40 .43 .47 .50 15" to 16"
TP800055-CDROBTC .019" .19 .28 .34 .39 .43 .48 .51 .55 14-1/2" to 15-1/2"
TP800067-CDROBTC .021" .24 .33 .41 .47 .53 .58 .63 .67 17" to 18"
TP800080-CDROBTC .023" .28 .40 .49 .57 .63 .69 .75 .80 17-1/4" to 18-1/4"
TP8001-CDROBTC .026" .35 .50 .61 .72 .79 .87 .94 1.0 18-3/4" to 19-3/4"
TP80015-CDROBTC .031" .53 .75 .91 1.1 1.2 1.3 1.4 1.5 18-1/2" to 19-1/2"
TP8002-CDROBTC .036" .71 1.0 1.2 1.4 1.6 1.7 1.9 2.0 18-1/2" to 19-1/2"
TP8003-CDROBTC .043" 1.1 1.5 1.8 2.1 2.4 2.6 2.8 3.0 18-1/2" to 19-1/2"
TP8004-CDROBTC .052" 1.4 2.0 2.5 2.8 3.2 3.5 3.7 4.0 18-1/2" to 19-1/2"
TP8005-CDROBTC .057" .18 2.5 3.1 3.5 4.0 4.3 4.7 5.0 18-1/2" to 19-1/2"
65˚
TP650039-CDROBTC .016" .14 .20 .24 .28 .31 .34 .36 .39 11-1/2" to 12-1/2"
TP650044-CDROBTC .017" .16 .22 .27 .31 .35 .38 .41 .44 12-1/2" to 13-1/2"
TP650050-CDROBTC .018" .18 .25 .30 .36 .40 .43 .47 .50 12-1/2" to 13-1/2"
TP650055-CDROBTC .019" .19 .28 .34 .39 .43 .48 .51 .55 12-1/2" to 13-1/2"
TP650067-CDROBTC .021" .24 .33 .41 .47 .53 .58 .63 .67 14-1/2" to 15-1/2"
TP650080-CDROBTC .023" .28 .40 .49 .57 .63 .69 .75 .80 14-1/2" to 15-1/2"
TP6501-CDROBTC .026" .35 .50 .61 .72 .79 .87 .94 1.0 16-1/4" to 17-1/4"
TP65015-CDROBTC .031" .53 .75 .91 1.1 1.2 1.3 1.4 1.5 15-1/2" to 16-1/2"
TP6502-CDROBTC .036" .71 1.0 1.2 1.4 1.6 1.7 1.9 2.0 14-3/4" to 15-3/4"
TP6503-CDROBTC .043" 1.1 1.5 1.8 2.1 2.4 2.6 2.8 3.0 15-1/2" to 16-1/2"
50˚
TP500044-CDROBTC .017" .16 .22 .27 .31 .35 .38 .41 .44 10-1/2" to 11-1/2"
TP500050-CDROBTC .018" .18 .25 .30 .36 .40 .43 .47 .50 10-1/2" to 11-1/2"
TP500055-CDROBTC .019" .19 .28 .34 .39 .43 .48 .51 .55 10-1/2" to 11-1/2"
TP500067-CDROBTC .021" .24 .33 .41 .47 .53 .58 .63 .67 12-1/2" to 13-1/2"
TP500080-CDROBTC .023" .28 .40 .49 .57 .63 .69 .75 .80 12-1/2" to 13-1/2"
TP5001-CDROBTC .026" .35 .50 .61 .72 .79 .87 .94 1.0 13-1/2" to 14-1/2"
TP50015-CDROBTC .031" .53 .75 .91 1.1 1.2 1.3 1.4 1.5 13-1/2" to 14-1/2"
TP5002-CDROBTC .036" .71 1.0 1.2 1.4 1.6 1.7 1.9 2.0 13-1/2" to 14-1/2"
TP5003-CDROBTC .043" 1.1 1.5 1.8 2.1 2.4 2.6 2.8 3.0 13-1/2" to 14-1/2"
TP5010-CDROBTC .078" 3.5 5.0 6.1 7.1 7.9 8.7 9.4 10.0 13-1/2" to 14-1/2"
131.800.95.SPRAY | Intl. 1.630.665.5000 | www.spray.com
* For solid stream tips, the actual orifice diameter is listed.** Spray pattern width is based on liquid with viscosity of 20 seconds, #4 Zahn Cup spraying at 1600 psi (110 bar). Tabulation is based on spraying water at temperature at 70°F (21°C).
Robotic TC Tips Performance Data
Spray Angle
at 40 psi
Spray Tip Number
Equiv. Orifice Dia. *
Capacity (gallons per minute)Spray Pattern Width
(at 1' Distance)**500 psi
1000 psi
1500 psi
2000 psi
2500 psi
3000 psi
3500 psi
4000 psi
40˚
TP400011-CDROBTC .009" .039 .055 .067 .078 .087 .095 .10 .11 6-1/2" to 7-1/2"
TP400017-CDROBTC .011" .06 .08 .10 .12 .13 .15 .16 .17 6-1/2" to 7-1/2"
TP400025-CDROBTC .013" .09 .12 .15 .18 .20 .22 .23 .25 7" to 8"
TP400044-CDROBTC .017" .16 .22 .27 .31 .35 .38 .41 .44 8-1/2" to 9-1/2"
TP400050-CDROBTC .018" .18 .25 .30 .36 .40 .43 .47 .50 8-1/2" to 9-1/2"
TP400055-CDROBTC .019" .19 .28 .34 .39 .43 .48 .51 .55 8-1/2" to 9-1/2"
TP400067-CDROBTC .021" .24 .33 .41 .47 .53 .58 .63 .67 10-1/2" to 11-1/2"
TP400080-CDROBTC .023" .28 .40 .49 .57 .63 .69 .75 .80 10-1/2" to 11-1/2"
TP4001-CDROBTC .026" .35 .50 .61 .72 .79 .87 .94 1.0 11-1/2" to 12-1/2"
TP40015-CDROBTC .031" .53 .75 .91 1.1 1.2 1.3 1.4 1.5 11-1/2" to 12-1/2"
TP4002-CDROBTC .036" .71 1.0 1.2 1.4 1.6 1.7 1.9 2.0 11-1/2" to 12-1/2"
25˚
TP250017-CDROBTC .011" .06 .08 .10 .12 .13 .15 .16 .17 5-1/2" to 6-1/2"
TP250039-CDROBTC .016" .14 .20 .24 .28 .31 .34 .36 .39 6-1/2" to 7-1/2"
TP250050-CDROBTC .018" .18 .25 .30 .36 .40 .43 .47 .50 7-1/2" to 8-1/2"
TP250055-CDROBTC .019" .19 .28 .34 .39 .43 .48 .51 .55 7-1/2" to 8-1/2"
TP250067-CDROBTC .021" .24 .33 .41 .47 .53 .58 .63 .67 8-1/2" to 9-1/2"
TP250080-CDROBTC .023" .28 .40 .49 .57 .63 .69 .75 .80 8-1/4" to 9-1/4"
TP2501-CDROBTC .026" .35 .50 .61 .72 .79 .87 .94 1.0 8-1/2" to 9-1/2"
TP25015-CDROBTC .031" .53 .75 .91 1.1 1.2 1.3 1.4 1.5 9-1/4" to 10-1/4"
TP2502-CDROBTC .036" .71 1.0 1.2 1.4 1.6 1.7 1.9 2.0 8-1/2" to 9-1/2"
5˚
TP050011-CDROBTC .009" .039 .055 .067 .078 .087 .095 .10 .11 2" to 3"
TP050039-CDROBTC .016" .14 .20 .24 .28 .31 .34 .36 .39 4" to 5"
TP050050-CDROBTC .018" .18 .25 .30 .35 .40 .43 .47 .50 4" to 5"
TP050067-CDROBTC .021" .24 .34 .41 .47 .53 .58 .63 .67 4" to 5"
TP0501-CDROBTC .026" .35 .50 .61 .71 .79 .87 .94 1.0 5-1/4" to 6-1/4"
TP05015-CDROBTC .031" .53 .75 .92 1.1 1.2 1.3 1.4 1.5 5-1/2" to 6-1/2"
TP0502-CDROBTC .036" .71 1.0 1.2 1.4 1.6 1.7 1.9 2.0 5-3/4" to 6-3/4"
0˚
TP00009-CDROBTC .026" .30 .43 .52 .60 .67 .74 .80 .85 —
TP0001-CDROBTC .028" .42 .60 .73 .85 .95 1.0 1.1 1.2 —
TP00015-CDROBTC .034" .62 .85 1.0 1.2 1.3 1.5 1.6 1.7 —
TP0002-CDROBTC .039" .81 1.2 1.4 1.6 1.8 2.0 2.2 2.3 —
TP0003-CDROBTC .043" .99 1.4 1.8 2.0 2.2 2.4 2.6 2.8 —
TP0004-CDROBTC .052" 1.5 2.2 2.6 3.0 3.4 3.7 4.0 4.3 —
TP0005-CDROBTC .057" 1.7 2.4 2.9 3.4 3.8 4.2 4.5 4.8 —
TP0006-CDROBTC .063" 2.1 3.0 3.7 4.2 4.7 5.2 5.6 6.0 —
14 1.800.95.SPRAY | Intl. 1.630.665.5000 | www.spray.com
ECRTC TipsBenefits
• Ideal for spraying viscous solutions such as thick paints, epoxies, adhesives and other solutions prone to clogging
• Even flat spray pattern minimizes overspray
• Tip orifice insert is recessed in a solid stainless steel tip body to protect against damage
• Erosion-resistant tungsten carbide orifice insert provides longer wear life than standard stainless steel tips
• CDECRTC tips feature a shorter tip holder than ECRTC tips and are designed for use in applications where the spray solution tends to dry quickly. The tip design helps the solution slide away from the orifice and prevents clogging caused by caking and build-up
Specifications
Maximum pressure: 4000 psi (276 bar)
Spray pattern: Even flat spray
Materials: Stainless steel body with tungsten carbide orifice
Ordering Information
Nozzle Type A B Net Weight
TP-ECRTC .375" .59" .32 oz
TP-CDECRTC .313" .59" .32 oz
Dimensions & Weights
ECRTC Tip
CDECRTC Tip
A
B
A
B
T p 5 0 0 0 5 0 — e C r T C | | | | Tip Spray Capacity Tip Code Angle Size Type
eCrTC Spray Tip
T p 5 0 0 0 5 0 — C D e C r T C | | | | Tip Spray Capacity Tip Code Angle Size Type
CDeCrTC Spray TipBased on largest/heaviest version of each type.
151.800.95.SPRAY | Intl. 1.630.665.5000 | www.spray.com
ECRTC Tips Performance Data
* Spray pattern width is based on liquid with viscosity of 20 seconds, #4 Zahn Cup spraying at 1600 psi (110 bar). Tabulation is based on spraying water at temperature at 70°F (21°C).
Spray Angle at 40 psi
Spray Tip Number
Equiv. Orifice Dia.
Capacity (gallons per minute)
Spray Pattern Width* at 1' Distance500
psi 1000 psi
1500 psi
2000 psi
3000 psi
4000 psi
110°
TP1100017- CDECRTC .011" .06 .08 .10 .12 .14 .16 15"
TP1100025-CDECRTC .013 " .09 .12 .15 .18 .22 .25 16"
TP1100039-CDECRTC .016" .14 .20 .24 .28 .34 .39 18"
TP1100050-CDECRTC .018" .18 .25 .30 .36 .43 .50 19-1/2"
TP110067-CDECRTC .021" .024 .33 .41 .47 .58 .67 20-1/2"
TP1100080-CDECRTC .023" .28 .40 .49 .57 .69 .80 22"
TP11001-CDECRTC .026" .35 .50 .61 .72 .86 1.00 23-1/2"
95°
TP950017-CDECRTC .011" .06 .08 .10 .12 .15 .17 13"
TP950039-CDECRTC .016" .14 .20 .24 .28 .34 .39 16"
80°
TP800039-CDECRTC .016" .14 .20 .24 .28 .34 .39 14"
TP800050-CDECRTC .018" .18 .25 .30 .36 .45 .50 15"
TP800055-CDECRTC .019" .19 .28 .34 .39 .48 .55 15"
TP800067-CDECRTC .021" .24 .33 .41 .47 .58 .67 16"
TP800080-CDECRTC .023" .28 .40 .49 .57 .69 .80 17-1/4"
65°
TP650017-CDECRTC .011" .06 .08 .10 .12 .14 .16 9.5"
TP650025-CDECRTC .013" .09 .12 .15 .18 .21 .24 10"
TP650039-CDECRTC .016" .14 .20 .24 .28 .34 .39 12"
TP650050-CDECRTC .018" .18 .25 .30 .36 .43 .50 13"
TP650067-CDECRTC .021" .24 .33 .41 .47 .58 .67 14-3/4"
50° TP500050-CDECRTC 0.018" .18 .25 .30 .36 .43 .50 11"
40° TP400055-CDECRTC .019" .19 .28 .34 .39 .48 .56 9"
16 1.800.95.SPRAY | Intl. 1.630.665.5000 | www.spray.com
Compatible Spray Guns
RotoClean® Airless Spray NozzlesBenefits
• Ideal for high-pressure manual paint spraying with Spraying Systems Co. and other manufacturers’ airless spray guns
• Quick and easy to unclog. Simply rotate tip 180° and blow obstructions out of the opening in the back of the tip
• Tungsten carbide orifice provides maximum erosion resistance for high-pressure spraying
• Easy to replace the orifice – no need to disassemble
• Guard safety feature
Specifications
Maximum pressure: 5000 psi (345 bar)
Spray pattern: Flat spray
Materials: Stainless steel holder with tungsten carbide orifice insert and protective nylon lugs
* Use Gasket No. 7894-NY for 106A-3.** Use Gasket No. 12552-NY for 106A-10.
RotoClean No. Connection Thread Size Gasket No. For
106A-2 225-2 11/16"-16 7894-NY SPRAYING SYSTEMS CO. 24 AUA AND GRACO
*106A-3 225-3 3/4"-16 19078-NY BALCRANK
106A-6 225-6 7/8"-14 11918-NY GRACO
106A-8 225-8 3/8" NPS 12552-NY NORDSON
106A-9 225-9 3/8" NPS 10660-NY DEVILBISS
**106A-10 225-10 3/4"-20 19079-NY BINKS 50
106A-11 225-11 M18 x 1 Metric 7894-NY ATLAS COPCO
106A-12 225-12 3/8" NPS 7894-NY SPEE-FLO
106A-13 225-13 M18 x 1 Metric 7894-NY DEICKE & KOPPERSCHMIDT
106A-14 225-14 1-14 9632-NY SPRAYING SYSTEMS CO. 44 AUA
106A-15 225-15 11/16"-16 12552-NY BINKS 43
106A-16 225-16 5/8"-14 BSPP 11918-NY —
106A-17 225-17 11/16"-16 13358-NY WAGNER
106A-18 225-18 M18 x 1.5 Metric 7894-NY —
225 RotoClean
106A RotoClean
171.800.95.SPRAY | Intl. 1.630.665.5000 | www.spray.com
* Tabulated capacities based on water.** Spray pattern width is based on liquid with viscosity of 20 seconds, #4 Zahn Cup spraying at 1600 psi (110 bar). Coverage will vary with viscosities and pressures.*** Available on special request.
RotoClean® Performance Data
RotoClean Insert Kits Capacity* (gallons per minute) Approx.**
Spray Pattern Width (at 1’
distance)
For 106A
Orifice Insert No. RC-
For 225 Handle/ Orifice Insert
No. 26081-
Equiv. Orifice Dia.
500 psi
1000 psi
1500 psi
2000 psi
WG 813 .013" .09 .12 .15 .18 16-1/2"
WH 815 .015" .12 .16 .20 .23 17"
WI — .016" .14 .20 .24 .28 18"
WJ 918 .018" .18 .25 .30 .36 19"
WK 1021 .021" .24 .33 .41 .47 21"
WA 1023 .023" .28 .40 .49 .57 22"
WL 1126 .026" .35 .50 .61 .72 23"
WM — .031" .53 .75 .91 1.1 25"
WN — .036" .71 1.0 1.2 1.4 26"
WO — .043" 1.1 1.5 1.8 2.1 27"
WP — .052" 1.4 2.0 2.5 2.8 28"
WQ — .057" 1.8 2.5 3.1 3.5 28"
WR — .062" 2.1 3.0 3.7 4.2 28"
WS — .067" 2.5 3.5 4.3 5.0 28"
WT — .072" 2.8 4.0 4.9 5.7 28"
WU — .076" 3.2 4.5 5.5 6.4 28"
WV — .078" 3.5 5.0 6.1 7.1 28"
WX — .089" 4.3 6.0 7.4 8.5 28"
9F 611 .011" .06 .08 .10 .12 13"
9G 713 .013" .09 .12 .15 .18 14"
9H 715 .015" .12 .16 .20 .23 15"
9I — .016" .14 .20 .24 .28 16"
9J 818 .018" .18 .25 .30 .36 17"
9K 921 .021" .24 .33 .41 .47 19"
9A 923 .023" .28 .40 .49 .57 19"
9L 1026 .026" .35 .50 .61 .72 21"
9M 1031 .031" .53 .75 .91 1.1 21"
9N 1036 .036" .71 1.0 1.2 1.4 22"
9O — .043" 1.1 1.5 1.8 2.1 22"
9P — .052" 1.4 2.0 2.5 2.8 23"
9Q — .057" 1.8 2.5 3.1 3.5 23"
9R — .062" 2.1 3.0 3.7 4.2 23"
9S — .067" 2.5 3.5 4.3 5.0 23"
9T — .072" 2.8 4.0 4.9 5.7 23"
9U — .076" 3.2 4.5 5.5 6.4 23"
9V — .078" 3.5 5.0 6.1 7.1 23"
9W — .085" 3.9 5.5 6.7 7.8 23"
9X — .089" 4.3 6.0 7.4 8.5 23"
RotoClean Insert Kits Capacity* (gallons per minute) Approx.**
Spray Pattern Width (at 1’
distance)
For 106A
Orifice Insert No. RC-
For 225 Handle/ Orifice Insert
No. 26081-
Equiv. Orifice Dia.
500 psi
1000 psi
1500 psi
2000 psi
9Z — .099" 5.3 7.5 9.2 10.6 23"
8E — .009" .039 .055 .067 .078 10-1/2"
8F 511 .011" .06 .08 .10 .12 11-1/2"
8G 613 .013" .09 .12 .15 .18 12-1/2"
8H 615 .015" .12 .16 .20 .23 13"
8I — .016" .14 .20 .24 .28 14"
8J 718 .018" .18 .25 .30 .36 15"
8K 821 .021" .24 .33 .41 .47 17"
8A 823 .023" .28 .40 .49 .57 17"
8L 926 .026" .35 .50 .61 .72 19"
8M 931 .031" .53 .75 .91 1.1 19"
8N 936 .036" .71 1.0 1.2 1.4 19"
8O — .043" 1.1 1.5 1.8 2.1 19"
8P — .052" 1.4 2.0 2.5 2.8 19"
8Q — .057" 1.8 2.5 3.1 3.5 19"
8R — .062" 2.1 3.0 3.7 4.2 19"
8S — .067" 2.5 3.5 4.3 5.0 19"
8T — .072" 2.8 4.0 4.9 5.7 19"
8U — .076" 3.2 4.5 5.5 6.4 19"
8V — .078" 3.5 5.0 6.1 7.1 19"
8W — .085" 3.9 5.5 6.7 7.8 19"
8X — .089" 4.3 6.0 7.4 8.5 19"
*** — .093" 4.6 6.5 8.0 9.2 19"
*** — .096" 4.9 7.0 8.6 9.9 19"
8Z — .099" 5.3 7.5 9.2 10.6 19"
7G — .012" .08 .11 .14 .16 11-1/2"
7I — .016" .14 .20 .24 .28 13"
6D — .007" .028 .04 .049 .057 8-1/2"
6E — .009" .039 .055 .067 .078 9-1/4"
6F — .011" .06 .08 .10 .12 10"
6G 513 .013" .09 .12 .15 .18 10-1/2"
6H 515 .015" .12 .16 .20 .23 11"
6I — .016" .14 .20 .24 .28 12"
*** *** .017" .16 .22 .27 .31 12-1/2"
6J 618 .018" .18 .25 .30 .36 13"
*** *** .019" .19 .28 .34 .39 13"
6K 721 .021" .24 .33 .41 .47 15"
6A 723 .023" .28 .40 .49 .57 15"
6L 726 .026" .35 .50 .61 .72 16"
18 1.800.95.SPRAY | Intl. 1.630.665.5000 | www.spray.com
* Tabulated capacities based on water.** Spray pattern width is based on liquid with viscosity of 20 seconds, #4 Zahn Cup spraying at 1600 psi (110 bar). Coverage will vary with viscosities and pressures.*** Available on special request.
RotoClean® Performance Data
RotoClean Insert Kits Capacity* (gallons per minute) Approx.**
Spray Pattern Width (at 1’
distance)
For 106A
Orifice Insert No. RC-
For 225 Handle/ Orifice Insert
No. 26081-
Equiv. Orifice Dia.
500 psi
1000 psi
1500 psi
2000 psi
6M 731 .031" .53 .75 .91 1.1 16"
6N 736 .036" .71 1.0 1.2 1.4 16"
6O — .043" 1.1 1.5 1.8 2.1 16"
6P — .052" 1.4 2.0 2.5 2.8 16"
6Q — .057" 1.8 2.5 3.1 3.5 16"
6R — .062" 2.1 3.0 3.7 4.2 16"
6S — .067" 2.5 3.5 4.3 5.0 16"
6T — .072" 2.8 4.0 4.9 5.7 16"
6U — .076" 3.2 4.5 5.5 6.4 16"
6V — .078" 3.5 5.0 6.1 7.1 16"
6W — .085" 3.9 5.5 6.7 7.8 16"
6X — .089" 4.3 6.0 7.4 8.5 16"
*** — .093" 4.6 6.5 8.0 9.2 16"
*** — .096" 4.9 7.0 8.6 9.9 16"
6Z — .099" 5.3 7.5 9.2 10.6 16"
5D — .007" .028 .04 .049 .057 7-3/4"
5E — .009" .039 .055 .067 .078 8"
5F 411 .011" .06 .08 .10 .12 8-1/2"
5G 413 .013" .09 .12 .15 .18 9"
5H 415 .015" .12 .16 .20 .23 10"
5I — .016" .14 .20 .24 .28 10-1/2"
*** *** .017" .16 .22 .27 .31 10-1/2"
5J 518 .018" .18 .25 .30 .36 11"
*** *** .019" .19 .28 .34 .39 11"
5K 621 .021" .24 .33 .41 .47 12"
5A 623 .023" .28 .40 .49 .57 13"
5L 626 .026" .35 .50 .61 .72 14"
5M 631 .031" .53 .75 .91 1.1 14"
5N 636 .036" .71 1.0 1.2 1.4 14"
5O — .043" 1.1 1.5 1.8 2.1 14"
5P — .052" 1.4 2.0 2.5 2.8 14"
5Q — .057" 1.8 2.5 3.1 3.5 14"
5S — .067" 2.5 3.5 4.3 5.0 14"
5T — .072" 2.8 4.0 4.9 5.7 14"
5V — .078" 3.5 5.0 6.1 7.1 14"
5Z — .099" 5.3 7.5 9.2 10.6 14"
4B — .005" .014 .020 .025 .028 6-1/2"
4C — .006" .021 .030 .037 .042 6-1/2"
4D — .007" .028 .040 .049 .057 6-1/2"
RotoClean Insert Kits Capacity* (gallons per minute) Approx.**
Spray Pattern Width (at 1’
distance)
For 106A
Orifice Insert No. RC-
For 225 Handle/ Orifice Insert
No. 26081-
Equiv. Orifice Dia.
500 psi
1000 psi
1500 psi
2000 psi
4E — .009" .039 .055 .067 .078 7"
4F 311 .011" .06 .08 .10 .12 7-1/2"
4G 313 .013" .09 .12 .15 .18 8"
4H — .015" .12 .16 .20 .23 8-1/2"
4I — .016" .14 .20 .24 .28 9"
*** *** .017" .16 .22 .27 .31 9-1/2"
4J 418 .018" .18 .25 .30 .36 10"
*** *** .019" .19 .28 .34 .39 10"
4K 521 .021" .24 .33 .41 .47 11"
4A 523 .023" .28 .40 .49 .57 11"
4L 526 .026" .35 .50 .61 .72 12"
*** *** .029" .46 .65 .80 .92 12"
4M 531 .031" .53 .75 .91 1.1 12"
4N 536 .036" .71 1.0 1.2 1.4 12"
4O — .043" 1.1 1.5 1.8 2.1 12"
4P — .052" 1.4 2.0 2.5 2.8 12"
4Q — .057" 1.8 2.5 3.1 3.5 12"
4R — .062" 2.1 3.0 3.7 4.2 12"
4S — .067" 2.5 3.5 4.3 5.0 12"
4T — .072" 2.8 4.0 4.9 5.7 12"
4U — .076" 3.2 4.5 5.5 6.4 12"
4V — .078" 3.5 5.0 6.1 7.1 12"
4Z — .099" 5.3 7.5 9.2 10.6 12"
3B — .005" .014 .020 .025 .028 5"
3C — .006" .021 .030 .037 .042 5"
3D — .007" .028 .040 .049 .057 5-1/2"
3E — .009" .039 .055 .067 .078 5-1/2"
3F — .011" .06 .08 .10 .12 6"
3G — .013" .09 .12 .15 .18 6"
3H 315 .015" .12 .16 .20 .23 7"
3I — .016" .14 .20 .24 .28 7"
3J 318 .018" .18 .25 .30 .36 7"
*** *** .019" .19 .28 .34 .39 7"
3K 421 .021" .24 .33 .41 .47 8"
3A 423 .023" .28 .40 .49 .57 8-1/2"
3L 426 .026" .35 .50 .61 .72 9"
3M 431 .031" .53 .75 .91 1.1 9"
3N 436 .036" .71 1.0 1.2 1.4 9"
3O — .043" 1.1 1.5 1.8 2.1 9"
191.800.95.SPRAY | Intl. 1.630.665.5000 | www.spray.com
* Tabulated capacities based on water.** Spray pattern width is based on liquid with viscosity of 20 seconds, #4 Zahn Cup spraying at 1600 psi (110 bar). Coverage will vary with viscosities and pressures.*** Available on special request.
RotoClean® Performance Data
Nozzle Type A B Net Weight
106A 5.375" 2.125" 8.5 oz
225 2.437" 2" 4.2 oz
Based on largest/heaviest version of each type.
Dimensions & Weights
A A 1 0 6 A – 2 + r C 2 F | | RotoClean Orifice Insert Number Kit
A A 2 2 5 – 6 + 2 6 0 8 1 - 8 1 3 | | RotoClean Orifice/Handle Number Insert Kit
106A rotoClean
225 rotoClean
Ordering Information
RotoClean Insert Kits Capacity* (gallons per minute) Approx.**
Spray Pattern Width (at 1’
distance)
For 106A
Orifice Insert No. RC-
For 225 Handle/ Orifice Insert
No. 26081-
Equiv. Orifice Dia.
500 psi
1000 psi
1500 psi
2000 psi
3P — .052" 1.4 2.0 2.5 2.8 9"
3R — .062" 2.1 3.0 3.7 4.2 9"
3T — .072" 2.8 4.0 4.9 5.7 9"
2B — .005" .014 .020 .025 .028 4"
2C — .006" .021 .030 .037 .042 4"
2D — .007" .028 .040 .049 .057 4-1/2"
2E — .009" .039 .055 .067 .078 4-1/2"
2F 211 .011" .06 .08 .10 .12 5"
2G 213 .013" .09 .12 .15 .18 5"
2H 215 .015" .12 .16 .20 .23 5-1/2"
2I — .016" .14 .20 .24 .28 6"
*** *** .017" .16 .22 .27 .31 6"
2J — .018" .18 .25 .30 .36 6"
2K 321 .021" .24 .33 .41 .47 6-1/2"
2A 323 .023" .28 .40 .49 .57 7"
2L 326 .026" .35 .50 .61 .72 7"
2M 331 .031" .53 .75 .91 1.1 7"
2N 336 .036" .71 1.0 1.2 1.4 7"
2O — .043" 1.1 1.5 1.8 2.1 7"
2P — .052" 1.4 2.0 2.5 2.8 7"
2R — .062" 2.1 3.0 3.7 4.2 7"
2T — .072" 2.8 4.0 4.9 5.7 7"
1B — .005" .014 .020 .025 .028 3"
1D — .007" .028 .040 .049 .057 3-1/2"
RotoClean Insert Kits Capacity* (gallons per minute) Approx.**
Spray Pattern Width (at 1’
distance)
For 106A
Orifice Insert No. RC-
For 225 Handle/ Orifice Insert
No. 26081-
Equiv. Orifice Dia.
500 psi
1000 psi
1500 psi
2000 psi
1E — .009" .039 .055 .067 .078 3-1/2"
1F — .011" .06 .08 .10 .12 4"
1G — .013" .09 .12 .15 .18 4"
1H — .015" .12 .16 .20 .23 4-1/2"
1I — .016" .14 .20 .24 .28 5"
1J 218 .018" .18 .25 .30 .36 5"
1K 221 .021" .24 .33 .41 .47 5-1/2"
1A 223 .023" .28 .40 .49 .57 5-1/2"
1L 226 .026" .35 .50 .61 .72 6"
1M 231 .031" .53 .75 .91 1.1 6"
1N 236 .036" .71 1.0 1.2 1.4 6"
0B — .005" .014 .020 .025 .028 2-1/2"
0D — .007" .028 .040 .049 .057 2-1/2"
0E — .009" .039 .055 .067 .078 2-1/2"
0F — .011" .06 .08 .10 .12 3"
0G — .013" .09 .12 .15 .18 3"
0H — .015" .12 .16 .20 .23 3-1/2"
0I — .016" .14 .20 .24 .28 4"
0J — .018" .18 .25 .30 .36 4"
0K — .021" .24 .33 .41 .47 4"
0L — .026" .35 .50 .61 .72 4"
0M — .031" .53 .75 .91 1.1 4"
0N — .036" .71 1.0 1.2 1.4 4"
B
B
A
A
North Avenue and Schmale Road, P.O. Box 7900, Wheaton, IL 60187-7901 USA
Tel: 1.800.95.SPRAY Intl. Tel: 1.630.665.5000 Fax: 1.888.95.SPRAY Intl. Fax: 1.630.260.0842
www.spray.com
Bulletin No. 644 Printed in the U.S.A. ©Spraying Systems Co. 2011
SprayNozzles
SprayControl
SprayAnalysis
SprayFabrication
Benefits
• Ideal for applications requiring a fine finish. Insert the Model HV orifice in the inlet of standard TC spray tips
• Produces a flat spray pattern with feathering spray pattern edges
Accessories
Capacity Size
Used With TC Tip
Tip Type Equiv. Orifice Dia.
8 -0008TC .007"
10 -0011TC .009"
12 -0017TC .011"
14 -0025TC .013"
16 -0033TC .015"
17 -0039TC .016"
19 -0050TC .018"
22 -0067TC .021"
24 -0080TC .023"
27 -01TC .026"
Model HV Orifice Performance Data
Orifice Type A B Net Weight
HV .25" .593" .32 oz
Dimensions & WeightsH v – 8
| | Orifice Type Capacity Size
Model Hv Orifice insert
Ordering Information
Model HV Orifice
B
A
Tip Retainer
Spray Tip
Screen Strainer
Gasket
Tip Gasket
High-Pressure Female
Nozzle Body
High-Pressure 11430 UniJet® Nozzle Body
Based on largest/heaviest version of each type.
Benefits
• Nozzle replacement costs are low because only the spray tips are replaced; the nozzle body can be reused
• Spray tip replacement is quick and easy – simply unscrew the tip retainer cap
• Interchangeable spray tips are available in a wide variety of spray patterns, spray angles and capacity sizes
• Orifice inserts, cores and strainers can be easily removed for inspection or cleaning
• Built-in strainer further prevents wear by keeping debris from entering the nozzle orifice; critical in applications using recirculated water