MN 87
· The system for photometric water analysis
Decomposition units for convenient sample preparation
NANOCOLOR® VARIO 2two separate heating units
capacity for 24 round glass tubes with 14 mm ID (16 mm OD)
Versatile combinations of
4 fixed temperatures (70 / 100 / 120 / 148 °C) and5 user-defined temperatures between 40 and 160 °C
with
4 fixed time settings (1/2 h, 1 h, 2 h, continuous) and5 user-defined digestion times between 00:01 h and 99:59 h
automatic temperature cut-off
PTFE covered heating units
2 separate safety shields
suitable for all NANOCOLOR® decomposition reactions
suitable for short time COD in 30 min
NANOCOLOR® Quattro 4 temperature settings 70 / 100 / 120 / 148 °C
capacity for 8 round glass tubes with 14 mm ID (16 mmOD) and
2 reaction tubes with 22 mm outer diameter
4 time settings: 1/2, 1, 2 hours and continuous operation
automatic temperature cut-off
suitable for all NANOCOLOR® decomposition reactions
NEW!
Heating blocks NANOCOLOR® VARIO 2 and Quattro
Technical data and ordering information
VARIO 2 QuattroCat. No. 919 04 919 39Mains voltage: 230 V – 50/60 Hz 230 V – 50 HzPower consumption: 500 VA 250 VADimensions: 260 x 285 x 160 mm 130 x 200 x 80 mmWeight: 3.85 kg 1.8 kg
These appliances comply with the following EC Directives:– 73/23/EEC of Feb. 19, 1973 – Low Voltage Directive– 89/336/EEC of May 03, 1989 (including Amendment Direc-
tive 92/31/EEC) – EMV Directive
MN88
· The system for photometric water analysis
In some countries government regulations require a completenitrogen balance for effluents. Besides ammonium, nitrite andnitrate, organic nitrogen compounds have to be determined –the sum of all these nitrogen compounds is called total nitro-gen. The Standard Method DIN/EN/ISO 11 905-1 describesthe procedure for the determination of total N. After formationof nitrate by oxidative decomposition of all inorganic and or-ganic nitrogen-containing substances, a subsequent nitrate
determination gives the total nitrogen content in mg N per li-tre.In samples with low nitrate and nitrite concentrations thismethod directly gives similar results to the determination ofTotal Kjeldahl Nitrogen TKN (including only ammonium andorganic nitrogen compounds). In the presence of detectableamounts of nitrate/nitrite, the TKN can be determined by sub-tracting nitrate/nitrite nitrogen from total nitrogen.
NanOx N · solid reagents for oxidative decomposition of samples containing nitrogen compoundsThe NANOCOLOR® system offers two rapid and convenientmethods for sample preparation with solid NanOx N rea-gents:a) regular decomposition in a heating blockb) vigorous pressurised decomposition in a microwave oven.NanOx N consists of convenient solid oxidative decomposi-tion reagents (potassium peroxodisulphate) and solid com-pensation reagents for elimination of interfering substances.After decomposition with NanOx N, the samples can be ana-lysed with NANOCOLOR® Nitrate tube tests.
a) Decomposition in a heating blockeasy handling
choice for everyday routine analyses
For this decomposition the following reagents and accesso-ries are required:
NANOCOLOR® total Nitrogen 22 (220) Test 0-83Cat. No. 985 083
Tube test 0.5 – 220 mg/l Nconvenient combination of NanOx N reagents, predosed tubetests for determination of total N and empty decompositiontubes (sufficient for 20 tests). Shelf life: at least 1 yearorNanOx N solid reagents Cat. No. 918 979+ empty reaction tubes 14 mm ID Cat. No. 916 80+ NANOCOLOR® Nitrate 50 Test 0-64
Cat. No. 985 064Tube test 0.5 – 22.0 mg/l NShelf life: at least 2 yearsDilution of the sample can considerably increase the measur-ing ranges.
Decomposition with NanOx N in a heating block
Postfach 10 13 52 · D-52313 Düren
NanOx N
Aufschlussreagenzdecomposition reagent
MACHEREY-NAGEL
5 ml
1 x
mix sample with NanOxdecomposition reagent
boil: 1 hour at 100 °Cor 30 minutes at 120 °C
add compensation reagent decomposed sample for the test procedure
0.2 – 0.5 ml
Postfach 10 13 52 · D-52313 Düren
NanOx N
Kompensationsreagenzcompensation reagent
MACHEREY-NAGEL
Special NANOCOLOR® procedures · Determination of total nitrogen TNb
MN 89
· The system for photometric water analysis
b) Pressurised microwave decomposition easy handling
rapid procedure
high recovery rates
recommended when decomposition in a heating block un-der normal pressure has failed
For the microwave decomposition the following reagents andaccessories are required:
Microwave testing unit Cat. No. 919 58consisting of microwave oven with turntable and digital timer,20 ml PTFE pressure vessel for decomposition with safety ex-pansion reservoir, set of sealing disks and safety dia-phragms, 100 ml Erlenmeyer flask, NanOx solid reagents
Pressurised microwave decomposition with NanOx N
mix sample with NanOx
decomposition reagentmicrowave decomposition
let cool in cold water add compensation decomposed
test proceduresample for the
Postfach 10 13 52 · D-52313 Düren
NanOx N
Aufschlussreagenzdecomposition reagent
MACHEREY-NAGEL
0 0 2 4
900W
0.2 – 0.5 ml
Postfach 10 13 52 · D-52313 Düren
NanOx N
Kompensationsreagenzcompensation reagent
MACHEREY-NAGEL
10 ml
2 x23 – 36 seconds ~ 5 minutes
reagent
Accessories for microwave decomposition
PTFE pressure vessel 20 ml for decomposition, with safety expansion reservoir, set of sealing disks/safety diaphragms 916 40PTFE pressure vessel 20 ml 916 43PFA sealing disks (pack of 20) 916 44PTFE safety diaphragms (pack of 10) 916 45PFA safety expansion reservoir 916 40.1PFA tubing with fitting 916 46PTFE boiling chips (pack of 3) 916 28Filter flocs MN 101 (pack of 500 g) 481 100Filter flocs MN 101 (pack of 1000 g) 481 110
Together with the NanOx reagents and the accessories listed above any microwave oven featuring a time setting in seconds and a power of minimum 750 W and maximum 900 W can be used for the NANOCOLOR® microwave decomposition.
Special NANOCOLOR® procedures · Determination of total nitrogen TNb
MN90
· The system for photometric water analysis
In many countries government regulations require a completephosphorus balance for effluents. Besides orthophosphates,also phosphonates and organic phosphorus compoundshave to be determined – the sum of all these compounds iscalled total phosphorus. After formation of phosphate by oxi-dative decomposition of all inorganic and organic phospho-rus-containing substances, a subsequent determination ofphosphate gives the total phosphorus content in mg P per li-tre.The NANOCOLOR® system offers several rapid and conven-ient methods for sample preparation and determination of to-tal phosphorus.
a) NANOCOLOR® tube tests for decomposition in a heating blocksolid reagent capsules for decomposition
predosed tube tests for determination of total P
decomposition and photometric evaluation in one and thesame test tube
the choice for everyday routine analyses
For a correct determination of total P with NANOCOLOR®
tube tests, the following reagents are available:
NANOCOLOR® ortho- and total Phosphate 1 Test 0-76Cat. No. 985 076
Tube test 0.010 – 1.50 mg/l P Shelf life: at least 1 year
NANOCOLOR® ortho- and total Phosphate 5 Test 0-81Cat. No. 985 081
Tube test 0.2 – 5.0 mg/l P Shelf life: at least 1 year
NANOCOLOR® ortho- and total Phosphate 15 Test 0-80Cat. No. 985 080
Tube test 0.3 – 15.0 mg/l P Shelf life: at least 1 year
NANOCOLOR® ortho- and total Phosphate 50 Test 0-79Cat. No. 985 079
Tube test 10.0 – 50.0 mg/l P Shelf life: at least 3 years
b) NANOCOLOR® standard tests and solid rea-gents NanOx Metal for decomposition in a heat-ing block
For frequent analyses of large numbers of samples, NANO-COLOR® standard tests are the choice for determination oftotal P. For a correct determination of total P the following re-agents and accessories are required:NanOx Metal solid reagents Cat. No. 918 978+ empty reaction tubes 14 mm ID Cat. No. 916 80
+ NANOCOLOR® ortho-Phosphate Test 1-77Cat. No. 918 77
Standard test 0.04 – 6.5 mg/l PShelf life: at least 3 yearsorNanOx Metal solid reagents Cat. No. 918 978+ empty reaction tubes 14 mm ID Cat. No. 916 80
+ NANOCOLOR® ortho-Phosphate Test 1-78Cat. No. 918 78
Standard test 0.2 – 17 mg/l PShelf life: at least 3 years
c) Pressurised microwave decompositioneasy handling
rapid procedure
high recovery rates
recommended when decomposition in a heating block un-der normal pressure has failed
For a correct determination of total P by microwave decom-position you need the following reagents and accessories:
Microwave testing unit Cat. No. 919 58consisting of microwave oven with turntable and digital timer,20 ml PTFE pressure vessel for decomposition with safety ex-pansion reservoir, set of sealing disks and safety dia-phragms, 100 ml Erlenmeyer flask, NanOx solid reagents
NANOCOLOR® tube tests ortho- and total Phosphateor NANOCOLOR® standard tests ortho-Phosphate
Together with the NanOx reagents and the accessories listedon page 89 any microwave oven featuring a time setting inseconds and a power of minimum 750 W and maximum900 W can be used for the NANOCOLOR® microwave de-composition.
Special NANOCOLOR® procedures · Determination of total phosphorus
MN 91
· The system for photometric water analysis
Together with the chemical oxygen demand (COD) the bio-chemical oxygen demand (BOD) is the most important sum-mary parameter for an estimation of the pollution of a wastewater. The BOD is defined as the amount of oxygen per vol-ume, which is used by the microorganisms at 20 °C for oxida-tive degradation of the organic substances present in thewater. Normally, the BOD is determined over a period of 5days, and is then called BOD5. MACHEREY-NAGEL offerstwo tests for the determination of the BOD5: a method withsample incubation in Winkler flasks, in accordance withDIN/EN 1899-1-H51, and a rapid simplified tube test.Benefits of NANOCOLOR® BOD5
recovery rates within the tolerances stated in DIN EN1899-1-H51
oxygen measurement similar to DIN EN 25813, no ma-nometers required
use of a nitrification inhibitor avoids oxygen consump-tion caused by oxidation of ammonium and nitrite (nitrifi-cation)
sample incubation in Winkler flasks in accordance withDIN EN 1899-1-H51 or
simplified incubation and oxygen measurement in oneand the same test tube
photometric evaluation with all types of NANOCOLOR®
photometers – no additional instrumentation necessary
automatic calculation of BOD5 with the photometer typeNANOCOLOR® 300 D or
clear evaluation form for hand-written step-by-step cal-cualtion ot the BOD5
For a correct determination of the BOD5 you need the follow-ing reagents and accessories:
a) BOD5 determination in Winkler bottlesaccording to DIN EN 1899-1-H51
NANOCOLOR® BOD5 Test 8-22Cat. No. 985 822
Tube test combined with Winkler bottles 2 – 3000 mg/l O2
Shelf life: at least 2 years
BOD5 accessories set Cat. No. 916 918
Includes useful accessories for sample preparation prior tothe determination of BOD5, recommended to be ordered withthe first order of the tube test BOD5
The accessories set consists of an electric air pump, 2 aerat-ing bricks, tubing, a 10-l PE container, a 1-l laboratory bottleand 4 Winkler bottles
BOD5 nutrient mixture Cat. No. 918 994
without nitrification inhibitor N-allylthiourea (ATU)ready-to-use supplementary reagents for preparation of theinoculating water for BOD5 test 822
BOD5 nutrient mixture Plus Cat. No. 918 995
with nitrification inhibitor N-allylthiourea (ATU)ready-to-use supplementary reagents for preparation of theinoculating water for BOD5 test 822
b) BOD5 determination as simplified tube test
NANOCOLOR® BOD5-TT Test 8-25Cat. No. 985 825
Tube test 2 – 3000 mg/l O2
Includes nitrification inhibitor N-allylthiourea (ATU) to preventfalsely high BOD5 results due to high ammonium concentra-tionsShelf life: at least 2 years
BOD5-TT accessories set Cat. No. 916 925
Includes useful accessories for sample preparation prior tothe determination of BOD5, recommended to be ordered withthe first order of the tube test BOD5-TTThe accessories set consists of an electric air pump, 2 aerat-ing bricks, tubing, a 1000-ml PE container and two 40-ml re-action vessels
Spare parts: Cat. No.
4 oxygen bottles according to Winkler 916 9194 aerating bricks 916 92010 reaction vessels for BOD5-TT 916 926
Special NANOCOLOR® procedures · BOD5 (biochemical oxygen demand)
MN92
· The system for photometric water analysis
Next to the COD and BOD5, the content of Total Organic Car-bon (TOC) is an additional parameter, suitable for the assess-ment of the extent of water pollution by organic substances.The quantity of oxygen needed to oxidize organic com-pounds, is expressed by COD or BOD5, whereas the TOCspecifies the over-all content of organic carbon in the sample;thus analysts obtain more precise information about the watercondition or the effeciency of waste water treatment, particu-larly with respect to carbon removal.After removal of interfering inorganic carbon (TIC), a rapidmonitoring of TOC can be realized with an easy and well con-sidered two-step procedure, using a handy cuvette combina-tion for sample preparation and photometric measurement.1. Oxidative sample decomposition
Oxidation of total organic carbon (TOC) and evaporationof the resulting CO2 through a permeable membrane
2. Photometric determination of TOCEvaluation of the coloured indicator solution
Benefits of NANOCOLOR® TOC 75:predosed reagents without hazardous oxidants or mer-curyeasy TIC removalclear and simple two-step procedurehigh recovery rates even for undissolved organic com-pounds due to vigorous oxidation and prickable sealingfor complete gas exchangehigh reproducibility turbidities in the sample do not enter the indicator cu-vette and thus do not interfere in the measurement
NANOCOLOR® TOC 75 Test 0-93Cat. No. 918 93
Tube test 5 – 75 mg/l TOCShelf life: at least 1 year
Accessories for TOC determination:
Magnetic stirring unit without heater Cat. No. 970 115Minimagnet for TOC (30 x 6 mm) Cat. No. 916 211Erlenmeyer flask 50 ml Cat. No. 916 212
Special NANOCOLOR® procedures · TOC (total organic carbon)
First results in 1.5 hours
prickable sealing for complete gas exchange
due to inflowing CO2, colour change indicates TOC
MN 93
· The system for photometric water analysis
The AOX content represents the sum of organically boundhalogens (chlorine, bromine, iodine) which are adsorbable toa suitable adsorbent; their concentration is expressed aschloride. The rapid test NANOCOLOR® AOX 3 allows the determina-tion of AOX in natural waters, industrial or municipal wastewaters and sea water. The test is based on an easy three-step procedure:1. Solid phase extraction with the NANOSORB adsorbent
for AOX according to DIN 38 409-222. Oxidative decomposition of the enriched adsorbent in a
heating block at 120 °C or in a microwave oven3. Photometric determination of AOX as chloride
Benefits of AOX 3The complete test procedure takes less than 60 minutes– when using a microwave oven for the decomposition,first results are obtained in even less than 30 minutes.No expensive instrumentation is required; the test can beperformed and evaluated with the usual equipment for pho-tometric water analysis.In contrast to carbon-based adsorbents, the use ofNANOSORB for AOX, a polymeric adsorbent pad,avoids interferences by inorganic halides, which can be re-moved entirely from the adsorbent. Even in sea water, withchloride contents of up to 20 g/l (!), reproducible results areobtained.For convenient handling, NANOSORB for AOX pads comeindividually prepackaged in plastic cartridges, protecting theadsorbent during adsorption.The use of predosed reagents shortens the procedureand reduces the analyst’s exposure to chemicals to aminimum.Outstanding recovery rates can be achieved, even in un-diluted samples with high COD contents.Application of the automatic pump set increases the sen-sitivity of the test kit and facilitates the use of NANO-SORB for AOX.
AOX analysis has never been so easy and reli-able before!For a correct determination of AOX you need the following re-agents and accessories:
NANOCOLOR® AOX 3 Test 0-07Art.-Nr. 985 007
Tube test 0.1 – 3.0 mg/l AOX0.01 – 0.3 mg/l AOX
Shelf life: at least 1 year
NANOCOLOR® starter set for AOX 3Cat. No. 916 111
Includes useful accessories for the determination ofAOX with reagent set AOX 3; recommended to be or-dered with the first order of reagent set AOX 3
Supplement kit for AOX 3Cat. No. 918 072
Contains additional oxidising reagents forthe sensitive AOX range (0.01 – 0.3 mg/l
AOX) as well as for COD-contaminated sam-ples between 50 and 1000 mg/l CODShelf life: at least 1 year
Pump set for AOX 3Cat. No. 916 115
Required to increase thesensitivity of reagent setAOX 3 or simply a usefulauxiliary for convenient solidphase extraction with NA-NOSORB for AOX
Special NANOCOLOR® procedures · AOX (adsorbable organically bound halogens)
MN94
· The system for photometric water analysis
NEW!
The chemical oxygen demand (COD) is one of the most im-portant parameters for the evaluation of industrial or munici-pal waste waters. It is defined as the amount of oxygen – inthe form of an oxidizing agent – consumed in the oxidation oforganic water components. For standard methods (titration)and in cuvette tests, potassium dichromate in sulfuric acidhas long been used as an oxidizing agent for COD analysis.In addition to organic substances, inorganic substances canbe simultaneously oxidized. Particularly higher chloride concentrations are known to inter-fere. They may cause falsely higher results; but more oftenchloride interference leads to totally irreproducible results.Therefore, during COD analysis, chloride ions are usuallymasked by mercury salts. However, mercury is toxic, maycause damage to the nervous system of human beings andanimals and in addition is persistant in nature. So meanwhilein many countries the use of mercury compounds for analyti-cal purposes is subject to stringent regulations. Application ofmercury-consuming analytical methods is forbidden as soonas they can be replaced by mercury-free methods.For the determination of the COD with tube tests one cannotsimply omit the mercury, since this may lead to false or nonreproducible results, due to chloride/salt interferences. Andusing a chemistry different to the potassium dichromatemethod (e.g. permanganate or manganese) may cause con-spicuous difficulties in comparison to results obtained withstandard methods or regular COD cuvette tests.Now, MACHEREY-NAGEL has developed a mercury-freeCOD test, which uses the established dichromate chem-istry, but substitutes the most toxic component – themercury salts – by a non-toxic chloride elimination tech-nique using a special cartridge.
Convenient chlorine removal cartridges eliminate chlo-ride interferences and the reliable dichromatechemistry leads to reproducible and compara-ble results. The basic procedure of theregular COD cuvette test has not beenchanged, so no additional methods mustbe learned.
Procedure:1. Pretreatment in 1 minute2. Regular COD digestion (2 h at 148 °C in a heating block)3. Photometric Measurement
Benefits of the Hg-free NANOCOLOR® COD test:Environment-friendly and analytically correct alternativeto regular COD testsEstablished dichromate chemistry for results compara-ble to standard COD tests and conventional (Hg contain-ing) tube testsNo toxic compounds are used for chloride (salt) elimina-tion For reproducible results, toxic mercury compounds arereplaced by effective non toxic salt removal technique.Use of chloride (salt) removing cartridges with capacityof up to 2000 mg/l Cl– per cartridgeNo vacuum pretreatment devices necessary for thesecartridges
Special NANOCOLOR® procedures · COD Hg-free
MN 95
· The system for photometric water analysis
NEW!
The metabolic activities of microorganisms have a substantialinfluence on the purification efficiency of a sewage plant.Therefore it is important for the operator of a sewage plant toknow whether and in which way introduced waste waters af-fect the metabolic activity of the microorganisms (the activat-ed sludge activity). Microorganisms contain a number of enzymes (among othersdehydrogenases), which are responsible for the degradationof the waste water constituents. These enzymes are presentin all living microorganisms. The detection of dehydrogena-ses is therefore the proof for the occurrence of living biomass.The long-established tests for determination of the dehydro-genase activity – standardized as German Standard Methods(DEV) – are based on the so-called TTC method. Basis of thisprocedure is the conversion of colourless 2,3,5-triphenyltetra-zolium chloride (TTC) to dark-red, water-insoluble 1,3,5-tri-phenylformazane (TPF), which is transferred to ethanol anddetermined either photometrically or visually via a rapidscreening test.
Benifits of NANOCOLOR® TTC / Sludge activity 150: The tube test contains all accessories neces-sary for the procedure – no special equip-ment is requiredThe evaluation is possible with all NANOCOLOR® photometers – no other instruments are necessaryProcedure in accordance with German Stan-dard Methods DEV-L3 and DEV-L4, but more convient handling and faster results!Rapid visual evaluation of the degree of stabilisation of asludge is possible
NANOCOLOR® TTC / Sludge activity 150 Test 8-90Cat. No. 985 890
Tube test 5 – 150 mg TPF0.050 – 2.300 E
Shelf life: at least 2 years when stored at 2 – 8 °C
The tube test NANOCOLOR® TTC / Sludge activity 150 allows the application of the following methods:Determination of the biochemical activity (AS) of sludge samples in µg TPF/mg dry mass of sludge
Characterisation of the action of waste water and waste water constituents towards sludge(stimulation or inhibition of the dehydrogenase activity DHA in %)
Rapid visual evaluation of the degree of stabilisation of sludge based on a simple screening method
Special NANOCOLOR® procedures · TTC (detection of microbial dehydrogenase activity)
MN96
· The system for photometric water analysis
The rapid test NANOCOLOR® HC 300 (Hydrocarbons) isbased on a MN-patented method. Hydrocarbons with a boil-ing temperature above 120 °C can be detected in a clear five-step procedure:1. extraction of hydrocarbons from the sample
2. removal of polar substances
3. evaporation of the extraction solvent
4. oxidative decomposition in a heating block
5. photometric determination of hydrocarbons
Benefits of NANOCOLOR® HC 300
applicable for water and soil
extraction without halogenated solvents
mercure-free reagents
outstanding selectivity
complete removal of polar substances by solid phase ex-traction with CHROMABOND® ALOX N columns
can be adapted to the determination of lipophilic sub-stances
evaluation with all types of NANOCOLOR® photometers– no expensive analytical instrumentation required
For a correct determination of hydrocarbons you need the fol-lowing reagents and accessories
NANOCOLOR® HC 300 Cat. No. 985 057Tube test 0.5 – 5.6 mg/l HC / 30 – 300 mg/kg HCafter extraction from water or soil samplesShelf life: at least 1 yearReaction tubes (empty, pack of 20) Cat. No. 916 80Threaded couplings (pack of 2) Cat. No. 916 04Stop valve for piston pipettes (pack of 100) Cat. No. 916 21
For determination of hydrocarbons in water
Extraction kit HC from water Cat. No. 918 571Shelf life: at least 18 monthsSeparation funnel 500 ml (pack of 2) Cat. No. 916 08Volumetric flasks 25 ml (pack of 2) Cat. No. 916 61
For determination of hydrocarbons in soil
Extraction kit HC from soil Cat. No. 918 572Shelf life: at least 18 months
Soxhlet apparatus 30 ml Cat. No. 915 05(additionally a heater is required)Extraction thimbles (pack of 25) Cat. No. 645 008Volumetric flasks 50 ml (pack of 2) Cat. No. 916 06
For removal of fatty acids, fat or other polar compounds
CHROMABOND® SPE columns ALOX N (pack of 20)Cat. No. 730 250
Plastic syringes 50 ml (pack of 10) Cat. No. 916 09Syringe adaptors (pack of 2) Cat. No. 916 03
Special NANOCOLOR® procedures · Hydrocarbons / lipophilic substances
MN 97
· The system for photometric water analysis
In practice an analysis often recovers only the quantity of met-als which is present in the sample as dissolved ions. If the to-tal content of a metal is to be determined, particularly samplesof highly contaminated water or industrial waste water mustbe decomposed to avoid falsely negative or falsely low re-sults. Usually, by applying acid and heat, undissolved metaloxides are dissolved, metal ions are released from complex-
es and adsorptive compounds or interfering organic sub-stances are eliminated. Thus, maximum recovery rates canbe achieved for the analysis of heavy metals. The NANOCOLOR® system offers various rapid and conven-ient methods for sample preparation with solid reagents forregular decomposition and liquid reagents for vigorous de-composition.
NanOx Metal · solid reagents for oxidative decomposition of samples containing heavy metalsNanOx Metal consists of convenient solid oxidative decompo-sition reagents (potassium peroxodisulphate) and solid neu-tralisation reagents for pH adjustment prior to the subsequentdetermination of metals.
a) Decomposition in a heating blockeasy handling
choice for everyday routine analysis
NanOx Metal Cat. No. 918 978+ empty reaction tubes 14 mm ID Cat. No. 916 80
b) Pressurised microwave decompositioneasy handling
rapid procedure
high recovery rates
recommended when decomposition in a heating blockunder normal pressure has failed
Microwave testing unit Cat. No. 919 58consisting of microwave oven with turntable and digital timer,20 ml PTFE pressure vessel for decomposition with safety ex-pansion reservoir, set of sealing disks and safety dia-phragms, 100 ml Erlenmeyer flask, NanOx solid reagents
Pressurised microwave decomposition with NanOx Metal
Together with the NanOx reagents and the accessories listed on page 89 any microwave oven featuring a time setting in secondsand a power of minimum 750 W and maximum 900 W can be used for the NANOCOLOR® microwave decomposition.
Decomposition with NanOx Metal in a heating block
NanOxMetall
MACHEREY-NAGEL
Postfach 10 13 52 D-52313 Düren
Aufschlussreagenzdecomposition reagent
5 ml
1 x
mix sample with NanOxdecomposition reagent
boil: 1 hour at 100 °Cor 30 minutes at 120 °C
add neutralisation reagent decomposed sample for the test procedure
0.2 – 4 ml
NanOxMetall
MACHEREY-NAGEL
Postfach 10 13 52 D-52313 Düren
Neutralisationsreagenzneutralisation reagent
After decomposition with NanOx Metal, the samples can be analysed with the following NANOCOLOR® tests:Test 1-02 Aluminium * Test 1-36 IronTest 0-98 Aluminium 07 * Test 0-37 Iron 3
Test 1-13 Cadmium Test 1-60 ManganeseTest 0-14 Cadmium 2 Test 0-61 Nickel 7Test 0-24 Chromate 5 (Chromium) Test 1-62 NickelTest 1-25 Chromate (Chromium) Test 1-95 ZincTest 1-53 Copper Test 0-96 Zinc 4Test 0-54 Copper 7* only with microwave decomposition
mix sample with NanOx
decomposition reagentmicrowave decomposition
let cool in cold water add neutralisation reagent decomposed
test proceduresample for the
NanOxMetall
MACHEREY-NAGEL
Postfach 10 13 52 D-52313 Düren
Aufschlussreagenzdecomposition reagent
0 0 2 4
900W
0.2 – 4 ml
NanOxMetall
MACHEREY-NAGEL
Postfach 10 13 52 D-52313 Düren
Neutralisationsreagenzneutralisation reagent
10 ml
2 x23 – 36 seconds ~ 5 minutes
Special NANOCOLOR® procedures · Oxidation of samples containing heavy metals
MN98
· The system for photometric water analysis
NANOCOLOR® Crack set Liquid reagents for oxidative decomposition of samples containing heavy metals The crack set is used for oxidative sample preparation in acid-ic medium (sulphuric acid / potassium peroxodisulphate) un-der normal pressure at 100 °C in a heating block. The crackset is recommended
for comlete and vigorous decomposition of very resist-ant samples
when microwave decomposition with NanOx has failed
when microwave decomposition can not be applied be-cause of high organic contamination of the sample
After decomposition, the samples can be analysed in accord-ance with the instructions for the respective NANOCOLOR®
tests.For this decomposition the following reagents and accesso-ries are required:
NANOCOLOR® Crack set Cat. No. 918 08Reagent set for sample preparationShelf life: at least 3 yearsReaction basis: decomposition with sulphuric acid/potassiumperoxodisulphate at 100 – 120 °C. Some stable heavy metalcyanide complexes are not completely destroyed.The NANOCOLOR® reagent set Crack set contains all rea-gents required for the oxidative decomposition and subse-quent neutralisation.Additionally, reagent sets for determination of the individualmetals are required.
NANOCOLOR® reagent set Sludge 50Liquid reagents for oxidative decomposition of sludge containing heavy metals In Germany, the use of sludge for soil improvement in farmingand forestry and in gardening is regulated by government reg-ulations which define the maximum contents of 7 heavy met-als (Cd, Cr, Cu, Hg, Ni, Pb, Zn) allowable in sludge for theabove applications. The NANOCOLOR® reagent set sludge50 allows even non-chemists to determine these contentswith high accuracy. It is, however, recommended that you ar-range for the supplier of the kit to provide instructions to thosemembers of your team likely to be involved in its use. With the exception of mercury and lead all of the above met-als can be determined with the NANOCOLOR® analyticalsystem. The photometers NANOCOLOR® 250 D and 350 Dcannot be used for this sludge analysis. When using the pho-tometers NANOCOLOR® Linus, 400 D or 300 D, you can di-rectly read results as mg/kg dried residue of sludge (S). For a decomposition of sludge we recommend the followingreagents and accessories:
NANOCOLOR® Sludge Cat. No. 918 50NANOCOLOR® Sludge Cat. No. 918 501
Reagent sets for decomposition with aqua regiaShelf life: at least 3 yearsReagent set 918 501 does not contain the nitric acid 65% andhydrochloric acid 37% required for the decomposition and isthus suited for airfreight. The acids have to be purchased sep-arately from a local laboratory supply store.Reaction basis: Mineralisation of sludge and soil sampleswith aqua regia at 100 °C and preparation of a solution formetal analysis according to DIN 38-414-S7. Additionally, rea-gent sets for determination of the individual metals are re-quired.
Accessories for crack set
Tube for sample decomposition 22 mm diameter, NS 19/26, with glass stopper 2 916 66Condenser 200 mm, type KS, NS 19/26 bottom and NS 29/32 top, with 3 m polyethylene tubing 1 916 67Absorption attachment for condenser, NS 29/32 1 916 68
After decomposition the samples can be analysed with the following NANOCOLOR® testsTest 1-132 Cadmium 1 – 100 *Test 1-253 + 1-25 Chromium 20 – 1800 *Test 1-53 Copper 20 – 4000 *Test 1-62 Nickel 2 – 400 *Test 1-95 Zinc 80 – 6000 ** ranges in mg/kg for NANOCOLOR® Linus, 400 D, 300 D
Accessories for sludge analysis
Combination of all equipment required for sludge analysis (without reagents, photometer and heating block): 1 mor-tar with pestle, 2 tubes for sample decomposition with stoppers, 1 condenser with connecting tubing, 1 absorption attachment, 100 filter circles MN 1670, 11 cm diameter, 100 filter circles MN 640 d, 15 cm diameter, 1 plastic wash bottle 500 ml, 1 holder for round glass tubes and tubes for sample decomposition, 2 volumetric flasks 100 ml, 1 Erlenmeyer flask 200 ml, 1 measuring cylinder 50 ml, 1 pipette 50 ml, 1 glass funnel each with 60 mm and 80 mm diameter, 100 test sticks pH-Fix 0 – 14, 1 double spatula 180 mm, safety glasses, instructions for use
916 10
Special NANOCOLOR® procedures · Oxidation of samples containing heavy metals
MN 99
· The system for photometric water analysis
A comprehensive analytical system should include all acces-sories required for the analytical procedure, such as equip-ment for sampling, sample preparation and conservation, fordecomposition reactions, extraction and filtration – from ana-lytical preparations to protective accessories for safe opera-tion. All these components improve analytical procedures andthus help to obtain optimum results.
NANOCOLOR® membrane filters Removal of turbidities (fine filtration) is recommended for tworeasons:
Turbidities interfere with photometric determinations, in-tense turbidities must be removed prior to the analysis.
When both soluble and total amounts of a substance(e.g. iron, manganese, COD etc.) have to be deter-mined, part of the sample has to be filtered to removeundissolved particles. The German Standard Methodsuse a pore size of 0.45 µm as standard for differenti-ation between dissolved and undissolved particles.
Additionally we offer a pore size of 1.2 µm.
Ordering information
Description Pack of Cat. No.
NANOCOLOR® membrane filters
Membrane filtration kit 0.45 µm: 2 syringes 20 ml and 25 CHROMAFIL® membrane filters 0.45 µm
1 kit 916 50
CHROMAFIL® membrane filters 0.45 µm 50 916 52Membrane filtration kit 1.2 µm: 2 syringes 20 ml and 25 CHROMAFIL® membrane filters 1,2 µm
1 kit 916 511
CHROMAFIL® membrane filters 1.2 µm 50 916 513
NANOCOLOR® accessories
Piston pipettes and pipette stand Exact dosage of water sample and reagents is prerequisitefor analytical accuracy. We offer a complete line of piston pi-pettes – with fixed or adjustable volume.
convenient operation – exact dosage
guarantees clean analytical work through use of dispos-able tips
high security when working with toxic or corrosive sub-stances, because direct contact is avoided
clean and safe storage of the valuable pipettes in a pi-pette stand
all pipettes are supplied with tip ejector
MN100
· The system for photometric water analysis
Piston pipettes and pipette stand
200 µl piston pipette (without tips) 1 916 72Plastic tips for 50 – 200 µl piston pipettes 100 916 915500 µl piston pipette (without tips) 1 916 53Plastic tips for 200 – 1000 µl piston pipettes 100 916 761,0 ml piston pipette (without tips) 1 916 71Plastic tips for 200 – 1000 µl piston pipettes 100 916 762,0 ml piston pipette (without tips) 1 916 917Plastic tips for 1.0 – 5.0 ml piston pipettes (inner seal) 100 916 9165 – 50 µl digital piston pipette, adjustable 1 916 5850 – 200 µl digital piston pipette, adjustable 1 916 914Plastic tips for 5 – 50 and 50 – 200 µl piston pipettes 100 916 915200 – 1000 µl digital piston pipette, adjustable 1 916 77Plastic tips for 200 – 1000 µl piston pipettes 100 916 761,0 – 5,0 ml digital piston pipette, adjustable 1 916 909Plastic tips for 1.0 – 5.0 ml piston pipettes (inner seal) 100 916 916Pipette stand for 6 piston pipettes 1 916 79
General analytical accessories
Reaction tubes 14 mm ID 20 916 80Volumetric flask 10 ml for reduced analytical preparations 2 916 42Volumetric flask 25 ml with NS 10/19 and polyethylene stopper for analytical preparations 2 916 61Volumetric flask 100 ml with NS 12/21 and polyethylene stopper 2 916 83Measuring cylinder 50 ml 1 916 84Pipette 20 ml, short version 1 916 62
Description Pack of Cat. No.
NANOCOLOR® accessories
MN 101
· The system for photometric water analysis
Bulb for filling pipettes 1 916 65Glass funnel 60 mm diameter 1 916 81Glass funnel 80 mm diameter 1 916 82Filter circles MN 1670, 11 cm diameter 100 470 011Filter circles MN 640 d, 15 cm diameter 100 205 015Plastic wash bottle 500 ml 1 916 89Magnetic stirring unit without heater 1 970 115Mini-magnets for stirring 5 916 211Timer with digital display and acoustic signal (up to 99:59 min) 1 916 96Electric air pump with delivery tube 1 916 55Double spatula, 18/8 steel, 180 mm long 1 916 94Porcelain mortar 90 mm diameter with pestle 1 916 88Holder for 15 round glass tubes and 2 tubes for sample decomposition 1 916 36Safety bottle for shaking COD test tubes 1 916 37Safety shield for heating block VARIO-1, transparent, for use with tube tests 1 916 59Safety kit, consists of safety glasses, gloves and rubber apron 1 kit 916 90
Photometer accessories for photometers NANOCOLOR® Linus / 400 D / 300 D / 250 D
NANOCOLOR® Linus manual 1 919 14NANOCOLOR® 400 D manual 1 919 09NANOCOLOR® 350 D manual 1 919 821Glass cuvettes, 10 mm optical path 2 919 33Glass cuvette, 50 mm optical path 1 919 35Semi-micro cuvette, 50 mm optical path 1 919 50Lids for glass cuvettes 10 mm 2 919 41Lids for glass cuvettes 50 mm 2 919 40Disposable plastic cells, 10 mm optical path 100 919 37Tungsten halogen lamp for NANOCOLOR® Linus 1 919 57Tungsten lamp for NANOCOLOR® 400 D / 350 D / 300 D / 250 D 1 919 787Protective covering for NANOCOLOR® Linus 1 919 42Protective covering for NANOCOLOR® 400 D / 350 D 1 919 18Mains adaptor for NANOCOLOR® 400 D / 350 D / 300 D / 250 D 1 919 06Inkjet printer for NANOCOLOR® Linus 1 919 15.1Inkjet printer for NANOCOLOR® photometers 1 919 15Zero modem cable, serial, 2 x 9 pin for connection to a PC 1 919 680Adaptor, 9 pin to 25 pin (depending on type of PC and selected interface) 1 919 681
Special filters for the photometers NANOCOLOR® 400 D / 350 D / 300 D / 250 D
Interference filter 412 nm for pesticide analysis (incl. installation) 1 919 812other special filters on requestAccessories for photometers NANOCOLOR® 25, 50 D, PT, PT-2, PT-3, 100 D, 200 D, 250 D, 300 D and SM-1 are still available on request.
Description Pack of Cat. No.
NANOCOLOR® accessories
MN102
Quality control for photometric water analysis
NANOCONTROL standard solutionsReagents, measuring equipment and personal handling are al-ready subject to validation, or frequent internal control in manylabs. Therefore, numerous customers rely on our NANOCON-TROL standards to obtain an objective picture of the quality ofanalyses carried out with the NANOCLOR® system.NANOCONTROL standards are ready-to-use standard solu-tions, which contain one or several substances in known con-centrations. Separate spike solutions (NANOCONTROL100+ solution) allow tracing of interferences, which may bepresent in the sample. Composition and concentrations ofmultistandards meet the requirements of specific user groupse. g. in waste water treatment, drinking water production andothers. The standards are supplied with a documentationform, in which expected concentration and given tolerancerange (from/to) are stated for each parameter; in additionthere is plenty of space for documentation of quality control.Application of NANOCONTROL standards permits easy ana-lytical quality control and simplifies the corresponding docu-mentation. The consistent use of NANOCONTROL standardsleads to an objective proof of the accuracy of the analysis car-ried out with the NANOCOLOR® system and confirms the op-erator’s confidence in the reliability of the measured results.
NANOCONTROL 100+ Addition (spike solution)Using spike solutions is recommended whenever:
you start a new analytical series with an unknown sam-ple matrix
you know that your sample contains interfering sub-stances, e. g. proteins, larger amounts of salts etc.
you find continuous major deviations from other analyti-cal procedures
you question the accuracy of your own analytical results
The principle of standard addition is, that you increase theconcentration of a sample in defined steps. The recovery rateis then an indication of possible interferences. When con-stant, proportional deviations occur, they can be counterbal-anced; thus, the result can be corrected.
100+ Addition
NANOCONTROL 100+standard addition for multistandards
100 ml sample solution to the ring mark
pipet 1.0 ml addition solution
add 1 x 1.0 ml 100+ spiking solution
e. g.
result before addition
theoretical increase
result after standard addition
0.73 mg/l 0.25 mg/l 0.98 mg/l
1 ml
The NANOCONTROL system for analytical quality control
MN 103
Quality control for photometric water analysis
NANOCONTROL single standards for analytical quality control
NANOCONTROL multistandards for analytical quality control
NANOCOLOR® test Dimension Concentration of the standard
solution
Addition per 0.5 ml 100+ spiking
solution
Number of tests
Cat. No.
AOX 3 (test 0-07) mg/l AOX 1.0 1.0 20 925 07BOD5 (test 8-22, 8-25) mg/l O2 210 – 10 925 82Chlorine (test 1-16) mg/l Cl2 1.00 – 30 925 17Chlorine 2 (test 0-17) mg/l Cl2 0.80 – 30Chromate 5 (test 0-24) mg/l CrO4
2– 2.0 0.4 15 925 24Chromate (test 1-25) mg/l CrO4
2– 0.40 0.4 15COD 60 (test 0-22, 0-27) mg/l O2 30 – 15 925 22COD 160 (test 0-26, 0-33,
0-93)mg/l O2mg/l TOC
10040
––
157
925 26
COD 15000 (test 0-28) g/l O2 4.0 – 30 925 28COD 1500 (test 0-29) mg/l O2 400 – 15 925 29Nitrite (test 1-67) mg/l NO2-N / NO2
– 0.060 / 0.20 0.02 / 0.065 15 925 68Nitrite 2 (test 0-68) mg/l NO2-N / NO2
– 0.30 / 1.00 0.02 / 0.065 15Phosphate 1 (test 0-76, 1-77, 0-81)
mg/l PO4-P / PO43– 1.00 / 3.07 0.10 / 0.31 7 925 76
Sulphite 100 (test 0-90 mg/l SO32– 50 – 15 925 90
TOC see COD 160
Note: For chlorine (tests 1-16 and 0-17) and sulphite (test 0-90), as standards simulation substances are used, which react in the same way as the original parameter.
Parameter NANOCOLOR® test Concentration of the standard solution
Confidence interval Number of tests
Cat. No.
NANOCONTROL multistandard Sewage outflow incl. NANOCONTROL 100+ standard addition 12 – 120 925 011
Ammonium 0-03 Ammonium 3 0.75 mg/l NH4-N 0.68 – 0.82 mg/l Ammonium 0-04 Ammonium 10 3.0 mg/l NH4-N 2.7 – 3.3 mg/l COD 0-26 COD 160 72 mg/l CSB 65 – 79 mg/lCOD 0-33 COD 300 72 mg/l CSB 65 – 79 mg/lNitrate 0-64 Nitrate 50 6 mg/l NO3-N 5.2 – 6.8 mg/ltotal N 0-83 total Nitrogen 22 12 mg/l N 10 – 14 mg/ltotal P 0-76 Phosphate 1 0.63 mg/l P 0.56 – 0.70 mg/l
0-81 Phosphate 5 2.5 mg/l P 2.2 – 2.8 mg/l
NANOCONTROL multistandard Sewage influx incl. NANOCONTROL 100+ standard addition 30 – 300 925 012
Ammonium 0-05 Ammonium 50 25 mg/l NH4-N 22 – 28 mg/lCOD 0-29 COD 1500 400 mg/l CSB 360 – 440 mg/lNitrate 0-64 Nitrate 50 15 mg/l NO3-N 13.5 – 16.5 mg/l
0-66 Nitrate 250 15 mg/l NO3-N 13 – 17 mg/ltotal N 0-83 total Nitrogen 22 (220) 75 mg/l N 67 – 83 mg/ltotal P 0-80 Phosphate 15 8.0 mg/l P 7.2 – 8.8 mg/l
0-81 Phosphate 5 3.2 mg/l P 2.9 – 3.5 mg/l
Multistandards can also be used for checking reagents and photometers from other manufacturers. The contents of one packageof each multistandard are sufficient for at least 1 repeated test of each parameter indicated. If you only check one or a few pa-rameters, then the number of individual determinations is increased. Shelf life: 1 year, 6 weeks after opened
Multistandard
KA-AblaufSewage, Outflow
Multistandard
KA-ZulaufSewage, Inflow
The NANOCONTROL system for analytical quality control
MN104
Quality control for photometric water analysis
NANOCONTROL multistandard Seepage water incl. NANOCONTROL 100+ standard addition 15 – 300 925 013
Ammonium 0-06 Ammonium 200 80 mg/l NH4-N 72 – 88 mg/lCOD 0-28 COD 15000 4.0 g/l CSB 3.6 – 4.4 g/lNitrate 0-66 Nitrate 250 30 mg/l NO3-N 27 – 33 mg/lortho-P 0-79 ortho-Phosphate 50 25 mg/l PO4-P 22 – 28 mg/l
NANOCONTROL multistandard Metals 1 incl. NANOCONTROL 100+ standard addition 15 – 60 925 015
Cadmium 1-13 Cadmium 0.10 mg/l Cd2+ 0.08 – 0.12 mg/l0-14 Cadmium 2 1.00 mg/l Cd2+ 0.80 – 1.20 mg/l
Chloride 0-19 Chloride 200 80 mg/l Cl– 75 – 88 mg/l0-21 Chloride 50 20 mg/l Cl– 18 – 23 mg/l
Chromium 0-243 total Chromium+ Chromate 5
1.00 mg/l Cr 0.80 – 1.20 mg/l
1-253 total Chromium + Chromate
1.00 mg/l Cr 0.80 – 1.20 mg/l
Fluoride 0-40 Fluoride 2 1.0 mg/l F– 0.8 – 1.2 mg/lIron 1-36 Iron 0.10 mg/l Fe3+ 0.08 – 0.12 mg/l
0-37 Iron 3 1.0 mg/l Fe3+ 0.8 – 1.2 mg/lSulphate 0-86 Sulphate 200 80 mg/l SO4
2– 72 – 90 mg/lZinc 1-95 Zinc 0.10 mg/l Zn2+ 0.08 – 0.13 mg/l
0-96 Zinc 4 1.0 mg/l Zn2+ 0.8 – 1.3 mg/l
NANOCONTROL multistandard Metals 2 incl. NANOCONTROL 100+ standard addition 15 925 016
Copper 1-53 Copper 0.6 mg/l Cu2+ 0.5 – 0.7 mg/l0-54 Copper 7 2.0 mg/l Cu2+ 1.8 – 2.2 mg/l
Lead 0-09 Lead 5 2.50 mg/l Pb2+ 2.25 – 2.75 mg/l1-10 Lead 0.25 mg/l Pb2+ 0.22 – 0.28 mg/l
Nickel 0-61 Nickel 7 2.0 mg/l Ni2+ 1.8 – 2.2 mg/l1-62 Nickel 0.6 mg/l Ni2+ 0.5 – 0.7 mg/l
Potassium 0-45 Potassium 50 20 mg/l K+ 18 – 22 mg/l
NANOCONTROL multistandard Drinking water incl. NANOCONTROL 100+ standard addition 15 – 30 925 018
Aluminium 1-02 Aluminium 0.50 mg/l Al3+ 0.45 – 0.55 mg/lAmmonium 1-05 Ammonium 0.20 mg/l NH4-N 0.17 – 0.23 mg/lChloride 1-20 Chloride 20 mg/l Cl– 18 – 23 mg/lIron 1-36 Iron 1.50 mg/l Fe3+ 1.40 – 1.60 mg/lManganese 1-60 Manganese 1.50 mg/l Mn2+ 1.40 – 1.60 mg/lSulphate 0-86 Sulphate 200 80 mg/l SO4
2– 72 – 90 mg/l
Parameter NANOCOLOR® test Concentration of the standard solution
Confidence interval Number of tests
Cat. No.
Multistandards can also be used for checking reagents and photometers from other manufacturers. The contents of one packageof each multistandard are sufficient for at least 1 repeated test of each parameter indicated. If you only check one or a few pa-rameters, then the number of individual determinations is increased. Shelf life: 1 year, 6 weeks after opened
Multistandard
SickerwasserSeepage water / Eaux d’infiltration
Multistandard
Metalle 1Metals 1
Multistandard
Metalle 2Metals 2
Multistandard
TrinkwasserDrinking water
The NANOCONTROL system for analytical quality control
MN 105
Quality control for photometric water analysis
Besides application of multistandards for quality control an-other means for certification of analytical results is the partic-ipation in a NANOCONTROL interlaboratory trial.The principle of the interlaboratory trial is, that all participantsobtain an unknown sample, which they analyse independent-ly with the instrumental equipment and tests available. Theresults are then returned to the company who organises theinterlaboratory trial and evaluated in accordance with DIN38 402 part 41 and 42. While for accredited laboratories thismethod has been obligatory since a long time, it is not yet es-tablished in the field of routine process control. We recom-mend a participation once or twice per year. The MN interlaboratory trial is suited for checking your individ-ual working procedures as well as the waste water parame-ters determined with NANOCOLOR® tube tests. 100 mlsolution for the interlaboratory trial are sufficient for at leastone repeated test of each of the following parameters: COD,NO3-N, NH4-N, total N and total P.
Procedure of a NANOCONTROL interlaboratory trial1. The participant gets 1 bottle with 100 ml solution for the
interlaboratory trial. The concentrations of this solutionhave been certified by an independent DIN laboratory.
2. The concentrations of the solution for the interlaboratorytrial have been adjusted to the ranges of the NANO-COLOR® tests and are used without dilution.
3. Together with the solution, the participant obtains a pre-printed evaluation chart, instructions for use and an en-velop for returning the chart with the analytical results.
4. At MACHEREY-NAGEL all returned protocols are sub-jected to an objective evaluation.
5. Finally every participant obtains an individual evaluationfor every returned result, a certificate for participationand technical support, if necessary.
NANOCONTROL interlaboratory trial for analytical quality control
Parameter Concentration range NANOCOLOR® test Cat. No.Ammonium 0.5 – 2.3 mg/l NH4-N 0-03 Ammonium 3
0-04 Ammonium 10COD 50 – 150 mg/l COD 0-26 COD 160
0-33 COD 300Nitrate 2.0 – 10.0 mg/l NO3-N 0-64 Nitrate 50total N 5.0 – 20.0 mg/l N 0-83 total Nitrogen 22 (220)total P 1.0 – 4.5 mg/l P 0-80 Phosphate 15
0-81 Phosphate 5
NANOCONTROL interlaboratory trial consists of 1 x 100 ml solution for the interlaboratory trial for determination of the above parameters, incl. evalu-ation, documentation and certificate
925 001
The NANOCONTROL interlaboratory trial
Evaluation Ammonium
2.0
1.5
1.0
0.5
0.0
[mg/
l]
1.55 1.53 1.51
IT 1.MV 2.MV
Presentation of the evaluation of the interlaboratory trial for 1 parameter
NANOCOLOR® Ammonium 3Total average in mg/l: 1.55 NH4-NConfidence interval in mg/l: 1.40 – 1.70 NH4-NYour results in mg/l Deviation in %
1.53 –1.31.51 –2.6
Very good work! Excellent agreement with the nominal value
MN106
MACHEREY-NAGEL · your partner for water analysis
Quality control for photometric water analysis
Quality assuranceDuring production, filling and storage, NANOCOLOR® rea-gents are constantly controlled by a quality system which ful-fils the requirements of DIN EN ISO 9001. Lot specific routineQA reports provide the constant quality of the calibrations ofour NANOCOLOR® reagents and ensure accuracy of givenresults over the entire shelf life of NANOCOLOR® test kits.
Customer information
Product literatureA large number of catalogues, leaflets with new products,special instructions, supplements to photometer manuals andothers are available for MACHEREY-NAGEL customers – ofcourse free of charge.We also present our products at all major exhibitions for wateranalysis and are happy to meet you there.
MACHEREY-NAGEL on the webMACHEREY-NAGEL presents its own homepage with versa-tile product information from all product ranges. The informa-tion is available in English or German.
Our web address is http://www.mn-net.com
Sales and serviceAll around the world, whereveryou are, there is always an MNdistributor nearby. Their staffcan be relied on to give youalways the best possible adviceabout our products for water analysis.They assist with orders and provide youwith all necessary service.If you request information about your local MNdealer, please do not hesitate to contact us.Phone: +49-2421-969-0Fax: +49-2421-969-199e-mail: [email protected]
MACHEREY-NAGEL
DIN EN ISO 9001:2000CERTIFIED