STEAM BATH EG/HGSafety information
ImportantThis section should be read carefully to ensure the safe and correct installation of your humidifier.
GENERALThis manual contains all details necessary for the planning and installation of the Steam bath EG/HGhumidifier. In addition commissioning and maintenance details are included.The manual is intended for use by engineers and properly trained technical personnel. Maintenance,servicing or repair work must only be carried out by suitable skilled and qualified personnel, thecustomer must be responsible for ensuring their suitability.Any risks or hazards, especially when working from ladders or towers should be identified by a skilledand Health and Safety representative and effective control measure put in place.No liability will attach to the Distributor if any damage, injury or accident is attributable to inattentive,inappropriate, negligent or incorrect operation of the machinery whether or not caused deliberately.Always isolate all electrical and water supplied before commencing any maintenance.Every effort has been made to ensure details contained in this manual are correct, however, in view ofthe wide range of conditions experienced in air handling systems, the information provided should onlybe used as a guide. Please contact your Agent if any doubt.
CORRECT USEElectroVap MC steam bathes are ONLY intended for use with air handling systems or direct airhumidification. ANY OTHER APPLICATION IS NOT CONSIDERED USE FOR THE INTENDEDPURPOSE. THE MANUFACTURER CANNOT BE MADE LIABLE FOR ANY DAMAGE RESULTINGFROM INCORRECT USE.
WATERSteam bathes are designed to be used with mains, demineralized R/O or softened water. On noaccount attempt to introduce any other fluid or chemical into the system. Water supply should notexceed 6.0 bar and installation should comply with local regulations.
ELECTRICITYAll work concerned with electrical installation MUST only be performed by skilled and qualifiedtechnical personnel (eg electrician or technicians with appropriate training). The customer MUST beresponsible for ensuring their suitability.It is the duty of the installer to ensure that suitable sized cables and MCB protection is provided.Please observe the local regulations concerning the provision of electrical installations.
WARRANTYFailure to specify and fit original parts and accessories will invalidate your warranty.
NOTEOur policy is one of continuous research and development. We therefore reserve the right to amendwithout notice the specifications given in this document.
3
STEAM BATH EG/HGDeclaration of conformity
DIRECTIVE APPLIEDELECTROMAGNETIC Compatibility Directive 89/336/EEC Machinery Directive 98/37/EC Amending Directive 89/392/EEC Low Voltage Directive 73/23/EECStandard(s) to which EN50081-1: 1992, EN50082-1: 1992 Conformity Is declared: EN349: 1993 EN60204-1: 1993, EN292 Parts 1&2: 1991
Manufacturer’s Name and AddressDEVATECRue Saint EloiBP 1276550 Ambrumesnil - FRANCE
Authorised Representative
Type of equipmentELECTROVAP STEAM BATH EG/HG
Model Name (s) & Series:EG/HG
Year of Manufacture2001
We the undersigned, hereby declare that the equipmentspecified above conforns to the above Directive(s) and Standard(s).
Signature :
Nom : MAZIRE Michel FFonction : PresidentDate : 20.09.2001
2
Steam bath EG/HG Contents
Safety information 3View of the unit 4Determination of the steam generator 5
INSTALLATIONUnit fixing 6Water connection 7Installation exemple 8Dimensions 9Condensate draining 10
ELECTRICAL INSTALLATION 11Steam output 12Electrical features 13
Steam bath EGWiring diagrams 14
Electrical connections 15 Option connections 16
Steam bath control panel 17-18-19-20-21
Steam bath HGWiring diagrams 22Electrical connections 23Option connections 24
ACCESORIES INSTALLATIONTemperature sensor 25Steam pipes 26Scent dispensor 27
Desinfecting 28SOFTWARE ASSISTANT
Front panel identification 29 ELMC commissioning 30Menu changing parameter system 31-32Menu user information 33-34Menu humidifier condition 35Faults messages 36
MAINTENANCEMaintenance of the cylinder 37Maintenance of the valves 38Spare parts 39Maintenance sheets 40
1
ELEC
TRIC
ALD
IN R
AIL
MIC
RO
PRO
CES
SOR
DIS
PLAY
PAN
ELPO
WER
LAM
P
CLE
ANAB
LE C
YLIN
DER
OR
DIS
POSA
BLE
CYL
IND
ER
DR
AIN
VALV
E
INLE
T VA
LVE
IDEN
TIFI
CAT
ION
SHEE
T
4
CLO
SIN
G D
OO
R B
Y SC
REW
CR
OSS
TO
LL
Photos nocontractuals
Determination of the steam generator
5
Mod
el o
f the
st
eam
gen
erat
orW
all i
n gl
ass,
pla
stic
etc.
Wal
l in ti
ling,
cim
ent,
ston
es e
tc.
Volu
me
min
i/max
iof t
he s
team
bat
h(m
3)
With
out
vent
ilatio
nW
ithve
ntila
tion
with
vent
ilatio
nW
ithou
tve
ntila
tion
Max
Pow
er in
KW
68 -
90
78 -
125
4 - 1
5
Stea
mpr
oduc
tion
Max
2,5
2 - 5
2 - 5
4 - 1
0
8 - 1
5
13 -
20
71 -
102
58 -
65
43 -
60
38 -
45
28 -4
0
20 -
30
14 -
22
6 - 1
6
3 - 8
3 - 8
Max
4
18 -
30
28 -
40
38 -
50
48 -
60
58 -
60
Max
1,5
Max
3,5
2,5
- 8
2,5
- 8
7 - 1
6
14 -
20
18 -
30
28 -
40
38 -
52
48 -
60
58 -
72
68 -
102
3 5,5 8 8 12 16 24 32 36 48 58 88
ELM
C 5
EG
/HG
ELM
C 8
EG/H
G
ELM
C 1
0 EG
/HG
ELM
C 1
0 EG
/HG
ELM
C 1
5 EG
/HG
ELM
C 2
0 EG
/HG
ELM
C 3
0 EG
/HG
ELM
C 4
0 EG
/HG
ELM
C 4
0 EG
/HG
ELM
C 5
0 EG
/HG
ELM
C 6
0 EG
/HG
ELM
C 9
0 EG
/HG
3,8 6 7,5
7,5
11 15,3
21,7
30,6
30,6
37,6
43,5
65,3
Max
2,5
Max
5,5
4 - 1
5
13 -
24
22 -
30
28 -
40
38 -
50
48 -
60
58 -
70
ELM
C E
G: U
nit+
rem
ote
cont
rol c
abin
et+
T°C
sen
sor.
ELM
C H
G: U
nit w
ith in
tegr
ate
gene
rato
r + T
°C s
enso
r.
in K
G/H
R
Steam bath EG/HG Unit fixing
InstallationTake the ELMC out of its packaging.
Check for any damage.
Damage to unit must be reported by registered letter to carrier within 3 working days.
Respect the free space all around the unit:The half bottom of the unit should be about at 1 to 1.5 m of the ground 1.25 m of the front of the unit and 60 cm on the right side should be observed toallow an easy access for the maintenance.
Mark the fixing holes and drills to the place
Put the plug within the hole.
Screw the screw diam 6 in the plug, leave them exceed about 10 mm. Hang up the unit in these screws (up and down) and screw.
Check the level of the uniusing a spirit level.
For the water and electrical connections see the water connection chapter.
Steam bath EG/HG Water connection
InstallationFresh water service must be used tosupply the unit. The water supply must also completethe following requirements.• Water quality: 30 to 1000s/cm• Water Pressure: 1-6 bar• Water Temp: less than 40°C The water supply connection is at the bottom of theunit. All the ELMC are delivery with a water inlethose (500mm long) 3/4 “fitting for direct connectionto humidifier 1/2” connection to cold water supply.
A Non-return valve should be located on thepipe and cold water service connection to theunit.
The inlet valve base has a basket filter (see pagen°35 part n°8).
The Humidifier ELMC can run with 3 different waterqualities:
TAP WATER For the cylinder maintenance periods seethe maintenance curve. The ELMC has a timecounter (hours, steam KG...) maintenance periodsalso a message Clean or Remote the cylinder.
SOFTENED WATER The ElectroVap MC humidifier may be usedwith softened water.IMPORTANT: Softeners must be programmedcorrectly. Failure to programm the softenercorrectly may lead to excessive salt concentration inthe steam cylinder. For assistance contact theSoftener Manufacturer.Reverse Osmosis and DemineralisedWater
The ElectroVap MC humidifier may be used withReverse Osmosis or Demineralised water. Theminimum water quality is 30 µ/cm. For each start up withnew a new steam cylinder, bicarbonate of soda will beadded.
The water level must be between (a)and (b) for the maximum cylindercapacity.
Softener D.I. water
b
Flexible hose supply
7
a
Exemple of a HAMMAM installation
1 St
eam
hum
idif
ier
STE
AM
BA
TH
EL
MC
EG
/HG
2St
eam
pip
e di
am 2
5 or
40
mm
rega
rdin
g th
e m
odel
3St
eam
noz
zle
4 T
empe
ratu
re s
enso
r5
Hos
edi
am 2
5 m
m to
go
dow
n to
the
drai
n6
Sew
erag
e di
am 4
0 m
m m
ini (
high
tem
pera
ture
)7
Pow
er s
uppl
y 3
x 40
0 v
+T+N
8
Wat
er s
uppl
y
8BIS
Dis
conn
ecto
r 9
Con
trol
cab
inet
(low
vol
tage
)10
Perf
ume
inje
ctio
n pu
mp
117
liter
s pe
rfum
e ta
nk12
Perf
ume
pipe
13 D
esin
fect
ing
unit
147
liter
s de
sinf
ecta
nt ta
nk15
Des
infe
ctio
n pi
pe16
Des
infe
ctiio
n pi
pe
17 S
team
bat
h18
Prot
ectio
n gl
assf
or l2
V la
mp
19 E
xtra
ctio
n of
hyg
ieni
c ai
r20
Siph
on to
war
d to
the
floo
r21
No-
skid
tilin
g in
ben
dto
war
d th
e si
phon
22St
eam
bat
h do
or23
Perf
ume
valv
e24
220
V e
lect
rova
lve
25A
nti-
retu
rn v
alve
STE
AM
3x40
0 V
T+
N
14
8
13
1012
6
5
7
2
16
4
18
9
19
3
20
21
22
17
15
pent
e
11
8BIS
2425
1
8
9
Steam bath EG/HG
DIMENSIONAL FEATURESELMC 5-8-10
ELMC 10 mono(230v) 15-20-30
ELMC 40-50-60
ELMC 90
Photos no contractual
DimensionsIN mm
Steamoutlet
Drainoutlet
weightempty
Kg
WeightFullKg
A 470 1 115 a 115 15 23B 540C 215D 425E 425F 20G 110H 380I 20
DimensionsIn mm
Steamoutlet
Drainoutlet
Weightempty
Kg
WeightfullKg
A 545 1 135 a 135 22 35B 675C 270D 465E 505F 40G 110H 525I 20
DimensionsIn mm
Steamoutlet
Drainoutlet
Weightempty
Kg
WeigtfullKg
A 840 1 140 a 140 30 60B 675 2 300 b 300C 270D 760E 795F 40G 110H 525I 20
DimensionsIn mm
Steamoutlet
Drainoutlet
Weightempty
Kg
WeightfullKg
A 1070 1 140 a 140 45 90B 675 2 275 b 275C 270 3 275 c 275D 990E 1030F 40G 110H 525I 20
Steam bath EG/HGCondensates outlet
10
Y = 130 mm
X = 100 mm
Y = 375 mm
X = 100 mm
Y = 550 mm
X = 150 mm InstallationThe above diagram concerns all neccesary workyou have to make for the draining.
Connection to the unit by a hose draining diam25ELMC 5-30: 1 m hose with 3 hose clipsELMC 40-60: 1m+1.20m hose with 6 hose clips.ELMC 90: 1m+1.20m+1.80m hose with 9 hoseclips
Please follow the recommandation hereafter. Drainhose internal diam mini.- ELMC 5/8/10/15/20/30 ø 25mm- ELMC 40/50/60 ø 25 mm- ELMC 90 ø 25 mm
The drain operates under gravity only. Ensurethe drain pipework a slope of at least 15°Cto allow the unit to drain efficiently.
You must use the drain hoses supplied byDevatec. Remove them periodically.
The temperature of the water discharged from thehumidifier is between 60°C and 100°C. Ensure thepipe work used is able to withstand suchtemperature
The discharge hose must be free without anyobstacle.
We recommand you each steam cylinder to have itsown drain pipe and tundish arrangements.This will permit fast and easy identification of afault within a cylinder.
The discharge point should be offset from theunderside of the unit as the scheme shows.This will prevent steam/condensate to enterthe cabinet.
11
Steam bath EG/HGElectrical installation
importantAll works concerned with the electrical installation
must be carried out by skilled and qualified personnel(eg electrician with appropriate training).
The customer is responsible for ensuring their suitability.Please observe local regulations concerning the provision
of electrical installations.
3X400VCurrent Capacity Power Capacity Power Capacity Power
MODELE Amps KG/V/H KW KG/V/H KW KG/V/H KWELMC5 16,2 /10 / 6 5,2 3,8 5,5 4 5,6 4,1ELMC8 15,2/ 8,8 8,3 6 8,3 6ELMC10 32 / 19,3/ 11 10,2 7,4 10,4 7,55 10,3 7,5ELMC15 26,7 / 16,2 14,4 10,5 15,1 11ELMC20 35 / 22,5 18,8 13,7 21 15,3ELMC30 47 / 32 25,3 18,4 29,8 21,7ELMC40 2X35 / 2X22,5 37,5 27,3 42,1 30,6ELMC50 2X43 / 2X27,7 46,2 33,6 51,7 37,6ELMC60 2X47 / 2X32 50,5 36,7 59,8 43,5ELMC90 3X47 / 3X32 75,6 55 89,8 65,3
3X600VCurrent Capacity Power Capacity Power Capacity Power
MODELE Amps KG/V/H KW KG/V/H KW KG/V/H KWELMC5 5,6/4,6/4,6 5,8 4,2 6,1 4,4 6,3 4,6ELMC8 7,7/6,2/5,6 8,3 6 8,3 6 7,8 5,7 ELMC10 10/7,8/7,7 10,7 7,8 10,5 7,62 10,7 7,8ELMC15 14/11/10,5 15,1 11 14,9 10,8 14,7 10,7ELMC20 19,3/16,2/14,1 20,8 15,1 21,7 15,8 20,4 14,8ELMC30 27,7/22,5/20,4 29,7 21,6 30,1 21,9 28,9 21ELMC40 2X19,3/16,2/14,1 41,5 30,2 43,5 31,6 39,5 28,7ELMC50 2X24,6/21/18,3 52,9 38,5 56,4 41 51,3 37,3ELMC60 2X27,7/22,5/21 59,4 43,2 60,4 43,9 58,9 42,8ELMC90 3X27,7/22,5/21 89,1 64,8 90,6 65,9 88,3 64,2
Courant enAmpère
2X230V KG/V/H
3X230V KG/V/H
3X400V KG/V/H
3X460V KG/V/H 3X575V KG/V/H
3X600V KG/V/H
2 0,63 1,09 1,90 2,18 2,73 2,845 1,58 2,73 4,74 5,45 6,81 7,11
10 3,15 5,45 9,48 10,90 13,63 14,2212 3,78 6,54 11,38 13,08 16,35 17,0615 4,73 8,18 14,22 16,35 20,44 21,3320 6,30 10,90 18,96 21,80 27,26 28,4425 7,88 13,63 23,70 27,26 34,07 35,5527 8,51 14,72 25,60 29,44 36,80 38,4030 9,45 16,35 28,44 32,71 40,88 42,6632 10,08 17,44 30,34 34,89 43,61 45,5137 11,66 20,17 35,08 40,34 50,42 52,6243 13,55 23,44 40,77 46,88 58,60 61,1547 14,81 25,62 44,56 51,24 64,05 66,84
Steam capacity
2X230V 3X230V
3X460V 3X575V
The two tables below show the nominal current and the nominal steam capacity in kg/v/haccording to the supply voltages.
This table enables to determine the steam quantity produced by the ELMC according to the intensity measured.
12
Electrical features
the below table shows the supply voltage features of the ELMC.
In all cases, the control circuit is supplied in 230 V, single phase.
4,6 4,6 4,68 6 7,7 6 6,2 5,7 5,610 7,8 10 7,6 7,8 7,8 7,715 11 14 10,8 11 10,7 10,520 15,1 19,3 15,8 16,2 14,8 14,130 21,6 28 21,9 23 21 20,440 30,2 2X19 31,6 2X16 28,7 2X1450 38,52X25 41 2X21 37,3 2X1860 43,2 2X28 43,9 2X23 42,8 2X219090 64,8 3X28 65,9 3X23 61,2 3X21 2 100 2,564,8 3X28 65,9 3X23 64,2 3X21 2 100 2,52 120 2,52 120 2,5
2 64 2,52 80 2,52 80 2,52 50 2,52 64 2,52 64 2,52 40 2,52 50 2,52 64 2,52 32 2,52 40 2,52 40 2,52 25 2,52 25 2,52 32 2,52 20 2,52 20 2,52 20 2,52 15 2,52 15 2,52 15 2,52 15 2,52 15 2,52 15 2,52 10 2,52 10 2,52 15 2,5
Con
trol c
ircui
t cab
lesi
ze in
mm
²
Ext
erna
l pro
tect
ion
cont
rol c
ircui
tAE
xter
nal p
rote
ctio
npo
wer
circ
uit A
Pm
axin
KW
Imax
inA
exte
rnal
pro
tect
ion
pow
er c
ircui
t A
Con
trol c
ircui
t cab
lesi
ze in
mm
²
Pm
axin
KW
Imax
inA
Ext
erna
l pro
tect
ion
cont
rol c
ircui
t A
Con
trol c
ircui
t cab
lesi
ze in
mm
²
ELM
C
3X460V∼ 50/60Hz 3X575V∼ 50/60Hz 3X600V∼ 50/60Hz
Pm
axin
KW
Imax
inA
Ext
erna
l pro
tect
ion
cont
rol c
ircui
tAE
xter
nal p
rote
ctio
n po
wer
circ
uit A
13
5 3,8 16 4 10 4,18 6 15,2 6 8,8
10 7,4 32 7,55 19,3 7,5 1115 10,5 26,7 11 16,220 13,7 35 15,3 22,530 18,4 47 21,7 3240 27,3 2X35 30,6 2X22,550 33,6 2X43 37,6 2X27,760 36,7 2x47 43,5 2X3290 55 3X47 65,3 3X32 2 120 2,52 160 2,5
2 80 2,52 120 2,52 80 2,52 100 2,52 64 2,52 100 2,52 40 2,52 60 2,52 32 2,52 47 2,52 20 2,52 47 2,52 15 2,52 32 2,52 47 2,52 15 2,52 20 2,52 10 2,52 15 2,52 20 2,5
Con
trol c
ircui
t cab
lesi
ze in
mm
²
Exte
rnal
pro
tect
ion
Con
trol c
ircui
t AEx
tern
al p
rote
ctiio
npo
wer
circ
uit A
P m
ax in
KW
I max
in A
Exte
rnal
pro
tect
ion
pow
er c
ircui
t Aco
ntro
l circ
uit c
able
size
in m
m²
P m
ax in
KW
I max
in A
Exte
rnal
pro
tect
ion
cont
rol c
ircui
t A
cont
rol c
ircui
t cab
lesi
ze in
mm
²
ELM
C
2X230V 50/60Hz 3X230V 50/60Hz 3X400V 50/60Hz
P m
ax in
KW
I max
in A
Exte
rnal
pro
tect
ion
cont
rol c
ircui
t AEx
tern
al p
rote
ctio
npo
wer
circ
uit A
6
4,25 5,6 4,4
WIRING DIAGRAM
ALL WORKS CONCERNED WITH ELECTRICAL INSTALLATION MUST BE CARRIED OUT BY A SKILLED AND QUALIFIED PERSONNEL.
X12 X16 7 8 9 10
X2
F1:2 A 11
12
X3 1314
X5201918
X6
2122232425
X801
X923
F2:2AX13
F3:2A
X1045
X14
X11
2829
DEVATECRéf:500100-02
X18
Type:n :
N1
215
16L
L2L1
43
PE
L3
X22X21X20X23
Réf.: 500400-02
K20 K21 K22
30 31 33 34 36 37
{32 35 38
2T14T2
14
NO 22
A2
6T3
NC
21
NOK
1
13
1L13L2
A1
NC
5L3
5051
5253
5455
56
16X417
15
Temperature sensor
34
Transfo
36363330
31
31
37
3757
1516
1516
57
BrownBlueGreen
white
Com (un-insolated)
X15
Marron
Bleu
Vert
Blanc Com
Brown
Blue
Green
White
Com(un-insolated)
Red
Black
6061
34
{See options
Power supply3 x 400 Vac 50/ 60 Hz +ground
Alande230 Va
Safety control {
Connection to the steam
Bath control panel
Control supply
230 Vac 50/60Hz
14
Electrical connections
34
K1
2T14T2
6T3
5L33L2
1L1NO 14
22
NC
A2
NO
NC
A1
1321
L1L2
L3N
L1
215
1650
51POMPE POUR DESINFECTANT EN 230 VAC
JUMP TERMINAL 1 AND 2
TEMPERATURE SENSOR
POWER SUPPLYBETWEEN L1, L2 & L3
CONTROL SUPPLYBETWEEN L AND N
GROUND CONNECTION
Alll worksqualified p
ON/OFF REMOTE CONTROL, CONTROL SAFETY OR
SEE AFTER OPTIONS
1) Shunté les bornes 1 et 2.2) Branché un fil rouge sur la borne 2.3) Branché le deuxiéme fil rouge sur la 4) Branché le fil blanc sur la borne 16.
Repère KTY81 ( joint noir )
5253
5455
56
concerned with electrical installation must be carried out by a skilled and ersonnel. 15
N1
215
16L
L2L1
43
PE
L3
2T14T2
14
NO 22
A2
6T3
NC
21
NOK
1
13
1L13L2
A1
NC
5L3
Fil rougeFil rouge
Fil blanc
borne 15.
CONNECTION OF THE OPTIONS
ALL WORKS CONCERNED WITH ELECTRICAL INSTALLATION MUST BE CARRIED OUT BY ASKILLED AND QUALIFIED PERSONNEL.
16
X12 X16 7 8 9 10
X2
F1:2 A 11
12
X3 1314
X5201918
X6
2122232425
X801
X923
F2:2AX13
F3:2A
X1045
X14
X11
2829
DEVATECRéf:500100-02
X18
Type:n :
N1
215
16L
L2L1
43
PE
L3
X22X21X20X23
Réf.: 500400-02
K20 K21 K22
30 31 33 34 36 37
4647
4849
{32 35 38
2T14T2
14
NO 22
A2
6T3
NC
21
NOK
1
13
1L13L2
A1
NC
5L3
5051
5253
5455
56
16X417
15
See wiring diagram
3334
30
3636
3330
31
31
37
3757
4646
57
X15
Brown
Blue
Green
White
Com(Un-insolated)
Red
Black
4949
6061
34Power supply3 x 400 Vac 50/ 60 Hz +ground
Alimenation de commande230 Vac 50/60 Hz
See wiring diagram {
See wiringDiagram
Des
infe
ctin
g pu
mp
Scen
t dis
pens
or p
ump
Ligh
t12
V
5
58
88
8
Control supply 230 Vac 50/60 Hz
Left light : shows the demand in light.
Central light : shows the perfume spreading
Right light : shows the on/off switcher position
Compact control cabinet with display panel for the steam bath close or far remote
This cabinet must be correctly connected to the ELMC EG.
This model offers:The ON/OFF control of the steam humidifier ELMC EG.The swith ON/OFF of the steam bath light.The setting of the steam bath temperature.The display of the temperature within the steam bath.The setting of the perfume dispensor.
The STEAM BATH control remote cabinet can be installed untill 60 meters from the steam bath.
The control cabinet is watertight and the push buttons are membrane made.
To respect the safety,the control cabinet is supplied with low voltage(12V).
STEAM BATH CONTROL CABINET
4 5 ° C45°C
TO CLEAN THE CONTROL CABINET NEVER USE A SOLVANT
17
4 5 ° C45°C
Wiring of your Steam Bath cabinet:
Fixing of your steam bath:
REMOTE WIRING AND FIXING OF THE CONTROL CABINET
Hole 13 mm.for wall wiring
76 45 3 2 1
4 5 ° C
15 mm
40 mm
130 mm
180
mm
4 X screws + pegs (supplied)
DEVATECREF 500700/01
X55 X56 X57
4 SCREWS (4 X 10)
BLANC
- Unscrew the 4 screws from the front cabinet of the Steam Bath, with a screw driver- Remove the front cover.- Put the back cabinet at the place you chose.- Mark off the 4 fixing holes (the foreseen hole are located at the same place that the front screws).
- Remove the back of the cabinet, drill with 5mm, put the pegs in place, position againthe back of the Steam Bath and screw the 4 screws supplied ( 3x25mm) with a screw driver.
- The Steam Bath remote control is provided with a wire sold per meter.(Indicate the lenght when you place your order).
- Please proceed to the wiring of your control cabinet by following the scheme below.
- You can also put the wires stuffing box at the back of the cabinet. (This space is foreseen, see the scheme below, hole 13mm).
Make the wiring as following:
-Green wire on terminal n° 1-Brown wire on terminal n° 2-Blue wire on terminal n° 3-Ground wire on terminal n°4-White wire on terminal n° 5-Red wire on terminal n° 6-Black wire on terminal n° 7
163
mm
103 mm
18Photos no contractual
Connection of the front panel control and Temperature sensor
56 55 54 53 52 51 50 49 48 47 46 16 15 2 1 DIN RAIL
TABLEAU DE COMMANDE A DISTANCE
TEMPERATURE SENSOR
WHITE
WIRE UN-ISOLED.
COMON.
12V forlight on
220V forscentdispensor
TEMPERATURE SENSOR.15 & 16 terminals.
(0 meters lenght)
Shunt or safety control
STEAM BATH ELMC
GREEN
BLUE
BROWNBLACK
RED
4 5 ° C45°C
IMPORTANT:Respect the colour of the stuf cable with the terminals above mentioned
19Photos no contractual
4 5 ° C45°C
STUFFING BOX
Front panel identification
Indications on the display panel:
MARCHE/ARRETECLAIRAGE
4 5 ° CTemperaturewithin the steambath.Variation of the temperature.
Temperature withinthe steam bath.
Steam production indicator.
Light ON/OFFindication in thesteam bath.
Steam production stopped.'ELMC EG is stopped.
Light is OFF
VAPEUR
VALIDATIONTOUCHE POU R
TOUCHE POURAUGMENTER
Using of the panel buttons:
20Photo no contractual
LIGHT ON/OFFSTEAM ON/OFF
ENTER TO DECREASE
TO INCREASE
Modification of the temperature setting point:
Modification of the perfume set point :
Modifications of the setting points
Push on the entry button the display indicates the temperature of theset point inside the steam bath.You can change it with the help of the buttons ( + ) or ( - ).DO NOT FORGET TO ENTER.
4 5 ° C45°C
6 0 ° C60°C
If any button ( + ) or ( - ) are used for a period of 10 secondes, the displayback at its initial position.
After the temperature it is possible to set the perfume spreading with button ( + ) and ( - )button.DO NOT FORGET TO ENTER.
20 % 50 %
Example of the rolling menu:
Adjustment of the temperature set point.(If needing)
Setting of the perfume dispensor.(If needing)
Back to the initial status.
21Photos no contractual
WIRING DIAGRAM
ALL WORKS CONCERNED WITH ELECTRICAL INSTALLATION MUST BE CARRIED OUT BYA SKILLED AND QUALIFIED PERSONNEL.
22
X12 X16 7 8 9 10
X2
F1:2 A 11
12
X3 1314
X5201918
X6
2122232425
X801
X923
F2:2AX13
F3:2A
X1045
X14
X11
2829
DEVATECRéf:500100-02
X18
Type:n :
N1
215
16L
L2L1
43
PE
L3
{
2T14T2
14
NO 22
A2
6T3
NC
21
NOK
1
13
1L13L2
A1
NC
5L3
16X417
15
Temperature sensor
1516
1516
X15
Marron
Bleu
Vert
Blanc Com
{SEE OPTIONS
Power supply3 x 400 Vac 50/60 Hz + ground
control supply230 Vac 50/60 Hz
Safety control {
Electrical connections
34
K1
2T14T2
6T3
5L33L2
1L1NO 14
22
NC
A2
NO
NC
A1
1321
L1L2
L3N
L1
215
16
POMPE POUR DESINFECTANT EN 230 VAC
SHUNT THE TERMINALS 1 AND 2
TEMPERATURE SENSOR
POWER SUPPLYBETWEEN L1, L2 AND L3
CONTROL SUPPLYBETWEEN L AND N
RACCORDING TO THE GROUND
See options
ALL WORKS CONCERNED WITH ELECTRICAL INSTALLATION MUST BE CARRIED OUT BYA SKILLED AND QUALIFIED PERSONNEL..
23
REMOTE CONTROL ON/OFF, CONTROL SAFETY OR
Electrical connection
ALL WORKS CONCERNED WITH ELECTRICAL INSTALLATION MUST BE CARRIED OUT BY ASKILLED AND QUALIFIED PERSONNEL.
24
X3 14Type:n :
L1
4948
6061
X18
X12 X1976 8
F1:2 A
X2
10
1211
13
4849
4849
12
1516
4746
Voir schéma de cablage
Asservissement sécurité
{{
Power supply3 x 400 Vac 50/60 Hz +earth
power control230 Vac 50/60 Hz
LN
L2L3
6146
34
PE
468
60
5
X14
DEVATECRéf:500100-02
X15
Green
White
X11
F3:2A
Brown
2829
45X10
23X9
22
X5
X4
Blue
Com
20
1615
17
1918
21
X6
X13F2:2A
01X8
252423 4
3
6T334
A2
NC
2T14T2
NO 22
14
1L13L2
5L3
21
K1
A1
NC
13
NO
88
5
Scen
t pum
p
Ligh
t12
V
Des
infe
ctan
t pum
p
Transformer for 12V light(3 lamps of 25W maxi)
See wiring diagramme
See wiring diagramme
Dimensions:
Wiring diagram:
Temperature sensor in vertical position:
Material supply:Sensor provide and connected with 10 mcable + 3 screws 3X25mm and pegs.
TEMPERATURE SENSOR
16 15THERMINAL ONTHE DIN RAIL
OF THE STEAM BATH
.If you install the temperature sensor at the ceiling of your steam bath:
It is possible to have a little water restaining(because of the condensation) at the end of the white cover
of the sensor..If this phenomenon appears or if you want to avoid it, remove the white cover of the sensor.
End to removeWhen cleaning the sensor, never use a solvant.
4mm55,5mm
60,5mm
3 hole of 3,2mmfor fixing
26mm forthe drill
25
Dimensions of the nozzle:
Dimensions of the steam nozzle union :
Dimensions of the nut:
Build up and example of the installation of the whole steam nozzle:
Steam nozzle
Steam
Steam nozzleSteam nozzle union Nut
Steam hoses25mm or40mm W
all
60mm
70m
m
5mm45mm 60mm
1"1/
4Gaz
30mm90mm in standard, 120mm out standard (upon request)
40mm
25mm
40mm
1"1/
4Gaz
Raw material:PTFE food
Raw material:PTFE food
1"1/4Gaz
8mm
26Photos no contractual
Dimensions:
Wiring diagram:
MATERIAL SUPPLIED:
Perfume dispensor
perfume pump 7 Liters tank Serpentin + perfume dispensor valve
63mm
47 46TERMINAL ONDIN RAIL OF THESTEAM BATH
Asse
mbl
e in
fact
ory
Never use solvantto clean the tankand the pump.
151mm
91mm
2 fixingholes
5,5mm for screws
4X40mm+ beggles
6mm supply.
260mm
204mm
Raw material:Polyethylene high density,food quality.
Air drain
On/Off
Lamp under power
Light indicationperfume missing
Quantity of perfume only available on HG(set at 100% for an EG)
25mm
connection tube (rilsan4/6), supplied per 25m.
27Photos no contractual
no-returnvalve.
Part gathered in factory
steam oultlettoward the steam nozzle.
steam inlet
Inlet of rilsan pipe4/6mm.
Brass Connection of the steam hose
25mm/ 40mm.
mm
Copper serpentin10mm.
2 X scews + plugs(supplied)
Dimensions:
Wiring diagram:
Material provided:
Desinfecting system
Desinfection pump 7 Liters tank Desinfecting nozzle
82mm
6,3mm
part
gath
ered
in
in fa
ctor
y
Never use a solvantto clean the pumpand the tank.
151mm
91mm
2 fixingholes
5,5mm for screw
4X40mm+ plugs
6mm supply.
260mm
204mm
Raw material: Polyethylenehigh densityfood quality.
Air trap
3 4
Part gathered in factory
Desinfectant nozzle suppliedwith 50cm of rilsan hose
4/6 and the fast union.
Tap water
7mm
7mm maxi
mm
Connection tube(rilsan 4/6), suppliedper 25m.
Lock nut 1".Drill 33mmfor wall.
TERMINAL ON THEDIN RAIL OF THESTEAM BATH
28Photos no contractual
2 X screws + plugs(supplied)
How to start the desinfection system:
Desinfection system
At this moment, push on the button to go back to the information's menu
To adjust the desinfection time:Please check with menu"Changing parameters" on page 32.To initiate the desinfection system:Push in the same time on and thedesinfection time begins to scrollsee the display.
DESINFECTIONTIME: 30 SEC
PUSH ENTERTO START AGAIN
28 bis
When this time is finished, the display indicates.
Front panel identification
Alpha digital screen
Changing program
Scrolling program
Scrolling program
Manual draining
Steam production lamp/light
Switch ON/OFF
Power lamp/light
Identification sheet
29
Your alpha numerical display
The stand-by light must be lighted.
Switch on I/O on I.
The display indicates “steam production” , we areare in the menu information user.
Check if th water supply is OK.
Check if the hygrostat or the proportional regulationis on demand, if yes, the steam production lamp is lighted
The following menu are proposed:. User's informationOnly on reading : inform the user about the the functionning on the unitand the selected parameters.
.Steam bath statusOnly on reading :inform since the starting of the starting of the unit.
. Parameter changingPreset in factory, only the final user or a qualifiedstaff thanks to a code (2,3,4),could change these parameters.
30
Caution : To scroll the menu, pressing on , an impulse at any time on allows you to change menu.
Changing parameters menu
Menu : CHANGINGDATA SYSTEM
ENTER ACCESS CODE :XXX
Please introduce yourcustomer access code.
LIMITATION :STEAM FLOW %
If steam bath EG If steam bath HG
The display indicates
PERFUME FREQUENCYINJECTION MN
T°C REGULATIONSTEAM BATH
31
To enter your access code:. Press on and thefirst red cross of your code is flashing.. Press by impulsing onto increase or decrease the number.Once you choose your number, confirm by pressing on and the second cross isflashing. Do again the same steps for the 2following numbers (votre code 2,3,4). allows to restrict output from 20 to 100 %
in ON/OFF and so one.
Allows to regulate the
frequencyof perfume
injection inminute.
Allow to regulate the
temperatureof thesteam bath.
Allows to settle the number of Kg steam/hbefore cleaning the cylinder
Allows to estimate the number of hours offunctionning before cleaningthe cylinder.
Allows to settle the time of a small cleaningThis small cleaning is made on each inlet water time.
CLEANING FREQUENCY KG/V
CLEANING FREQUENCY H
SEQUENTIAL DRAINING SEC
Take care: Rolling the menu in pushing on , pressing the select button in any time, allow to change the menu
Changing parameter
CONTACTOR STOP WHENDRAINING NO
CYLINDER SELECT
DESINFECT.TIMEINJECTION SEC
DESINFECT.FREQINJECTION SEC
LOCKING THE BUTTONSETTING SB NO
DRAIN AFTER PERIODYES/NO
YES NO
Alpha digital status
DRAINING AFTER ASHUTDOWN H
Back to the first menu
32
this function enable to choose between anadjustment by evaporation (for DI water)or by draining.
Enable to have the suitable cylinderDISPOSABLE/CLEANABLE for tapwater, soft or DI.
AJUSTEMENT KG/STPER :
Allow an automaticdraining
when humidityis not neccessary
The unit will be drained if there is no demandfor Humidity after the select time. Allow the time for the above to be selectedFactory setting: 72hr, options: 12-168 hr in 12 hrintervals. If NO, the function will not appears
Enable to set the frequency injectionof the desinfection in second.
Enable to set the frequency injectionof the desinfecting in minute.
Enable to lock or unlock the button
of the remote steam bath control panel.
Steam bath EG Steam bath HG
Alpha digital status
Take care : Rolling the menu in pushing on , pressing the select buttonin any time, allow to change the menu.
USER INFORMATION
Menu :USERINFORMATION
STEAM BATH ELMC
STEAM PRODUCED :ST/H
H
ACTUAL CURRENT : A
A
Steam bath EG Steam bath HG
Alpha digital status
T° IN THE BATH °C
STEAM DEMAND %
YES NO
Alpha digital status
DRAIN AFTER H.SHUT DOWN
In the menu: change parameter system, if the selectionoption is YES or NO (draining if no select time demand .
33
Indicates the ELMC model.
Indicates the nominal steam production of the ELMC.
Indicates the Amps consumption ofthe unit
Indicated the T°Winthin theSteam bath.
Indicates the steam demand in the'installation from 20% to 100%.
The unit will bedrain if there
is no demandafter the selected
time
Take care : Rolling the menu in pushing on , pressing the select button in any time, allow to change the menu.
MENU USER INFORMATION
PRODUCT BEFORECLEAN KG/ST
TIME METER H
STEAM METER KG
LOW MINERALCONCENTRATION
ELECTRICAL POWER KW
You return to the first menu
Indicates the steam production time before maintenance, allow to planify thecleaning intervention.
Indicates the time running periodbetween two interval maintenance.
Indicates the optimum conductivity
.
Indicates the power use by theELMC in KW.
34
NEXT SERVICE DUE H
1-2 Reverse timers (time before maintenance or production before cleaning) when you are on 0 the panel displays maintenance : VALVE DRAINING+ CYLINDER. The reverse timer reset is done, pushing on the manual draining button.
3-4 Timers (hours and steam) can be set on the zero again pushing on the manual drain button, followed by a pressure on the enter button.
Take care : Rolling the menu in pushing on , pressing the select buttonin any time, allow to change the menu.
MENU STEAM BATH STATUS
Menu :STEAM BATHSTATUS
CONTROL SIGNALSTEAM BATH (°C)
TOTAL STEAM RUN KG/VAP < >
TOTAL HOURS RUN H
CYLINDRE USED :
POWER SUPPLY V
MAXIMUM POWER INSTALL KW
You return to the first menu
WATER USED :
Total steam production since thefirst use.
Indicates the hours running since thefirst use.
Indicates the water used:tap water, soft water, partial DI water,DI water, supplying the unit.
Indicates the cylinder used:Disposable:Tap water (EV), soft water (EA),DI water(ED), Cleanable: Tap water(EV), soft water (EA), DI waterin the unit.
Indicates the voltage choised for the power circuit.
Indicates the maximum electricalpower choised for the ELMC
Indicates the regulation used
35
Electrovap MCElectrical features
Software assistant
36
FAULTY STATEMENT OF THEMESSAGES TROUBLE CAUSES/SOLUTIONS OPTION UNIT AFTER FAULTY
DETECTIONS
OF THE CONTACTOR see the coil Unit requests steam Fuse F1 2 ampsP1 the contactor does coil in short circuit blows out, UNIT STOP
not switch off Change the contactor Standard
SEE THE CONTACTOR Unit does not requestCONTACT IS STICKED steam and the Change the contactor Standard UNIT STOP
ONE - P2 contactor is off
LEACKAGE ON THE The inlet valve Check the water pressureINLET VALVE - P3 does not close (1.6 bars) Standard UNIT STOP
anymore or change the inlet valve
MISS OF WATER - P4 The water supply Check the supply water has a trouble Check the fuse F2 Standard UNIT STOP
If out of orderchange the inlet valveClean the drain valve
SEE THE DRAIN draining of water Maintenance of the cylinderCIRCUIT - P5 does not make (calcium bock)down the drain Standard UNIT STOP
correctly Fuse F2 out of ordergrain coil in short circuit
LEAKAGE WATER - P6 Water leakage Check there is no leakage Necessarydetected in the from the cylinder to have UNIT STOP
humidity change the gasket or the a leakagecompartiment cylinder if needed water detection
37
Electrovap MCInspection maintenance
MaintenanceThe ElectroVap ELMC is delivered with disposable cylinder(s) in standard whichcan be replaced by cleanable ones, however, without any modification, accordingto the choice of the user. Drain the steam cylinder using the manual drain key.When the cylinder is fully drained switch off the unit and isolate the power. Thesteam cylinder may be very hot. Allow it to cool down before removing.Remove front panel from the humidifier to access the cylinder compartment.Disconnect the steam hose from the top of the steam cylinder. Remove power andhigh water level electrodes from top of the steam cylinder.
Lift the cylinder upwards until it is clear of the drain valve. Ensure the retaining ringremains in the drain valves. The Disposable cylinder will be merely replaced bynew ones.
Cleanable cylinder:Mark the edge of the cylinder halves so the can be matched up whenreassembled.
Note:The constant heating and cooling of the cylinder may cause distortion.Consequently the cylinder halves must be assembled in the same relative position.Remove nuts and bolts around the centre of the cylinder. Open up cylinder. It isimportant that the strainer in the bottom half of the cylinder is also cleaned.
Clean the electrodes by scraping off the mineral deposits. Alternatively, this can bedone using weak descaling solution. Rinse the electrodes and the body of thecylinder. IT IS IMPORTANT TO AVOID DISTORtion THE CYLINDER INATTEMPTING TO REMOVE ANY MINERAL DEPOSITS FROM IT. Relocate thestrainer in the cylinder base. Replace the cylinder gasket on the rim of the bottomhalf of the cylinder and then locate the upper half of the cylinder on the gasket,TAKING CARE THAT THE MARKS ARE ALIGNED. Refit the nuts and bolts.Clean the O-ring on the drain valve and if necessary, change it. (every2-3 cylindercleanings). Locate the steam outlet of the cylinder in the retaining clip.Position thebase of the cylinder over the drain valve and push downwards. Reconnect thepower cables.
General:The humidifier requires regular maintenance to ensure efficient operation and toprevent breakdown.The exact maintenance frequency is variable and will depend on water quality,hours run and level of demand for humidification.New installations should be inspected / serviced every 2 to 4 weeks. This may betoo frequent, but it will enable a suitable maintenance routine to be established.
Routine inspection:The following is a guide to work that should be undertaken in a routine inspection.1 - Inspect water and steam installation for leaks and damage.2 - Inspect electrical installation for any loose cables and or damages.
Components.3 - Inspect the steam cylinder for scale deposits. If the scale in the cylinder is
half way up the stainer in the lower half of the cylinder it should bereplaced / cleaned (see changing steam cylinder).
4 - Inspect the inlet valve. The drain valve may become blocked with scalefrom the steam cylinder. This will cause water to continually run to drain.
Electrovap MCValves maintenance
Maintenance
38
Drain the steam cylinder fully and remove it from thehumidifier. Isolate power and water supply beforeattempting to carry out any maintenance.• Remove the cap from, the end of the electrovalve 1• Remove the coil from the valve steam 2• Unscrew and remove the valve steam from the valvebody 3• Clean the valve stem with fresh water 3• Clean the valve seat and the piston (taking care not toloose the spring) 7• Remove the O ring and drain valve collar from the top ofthe valve body 4NoteOil the O ring with high temperature siliconeoil before replacing. Remove the filling cup hose fromthe valve body. Remove the two screws that secure thevalve body to the drain cup 5. Remove the drain valvebody from the drain cup and rinse with clear waterensuring any scale deposits are removed. Pay particularattention to the pistion seat 6. Assemble in reverse order.
Drain the steam cylinder fully and remove it from thehumidifierIsolate power and water supply before attempting tocarry out any maintenance.• Remove the water inlet hose from the valve. 1 Removethe solenoid coil in pushing and turning 2•Remove the basket filter from the base of the valve with apair of long nose pliers. 3•Wash the basket filter under clean water to remove anydirt and debris. 3 Change the O ring if necessary 4•Assembly in reverse order.NoteDo not forget to fit the washer when attaching the waterinlet hose.
Drain valve maintenance
Inlet valve maintenance
These maintenance should be made at each cylinder maintenance
These maintenance should bemade twice a year.
..................................................................................................................................................................
..................................................................................................................................................................
..................................................................................................................................................................
..................................................................................................................................................................
..................................................................................................................................................................
..................................................................................................................................................................
..................................................................................................................................................................
..................................................................................................................................................................
..................................................................................................................................................................
..................................................................................................................................................................
..................................................................................................................................................................
..................................................................................................................................................................
..................................................................................................................................................................
..................................................................................................................................................................
..................................................................................................................................................................
..................................................................................................................................................................
..................................................................................................................................................................
..................................................................................................................................................................
..................................................................................................................................................................
..................................................................................................................................................................
..................................................................................................................................................................
..................................................................................................................................................................
..................................................................................................................................................................
..................................................................................................................................................................
..................................................................................................................................................................
..................................................................................................................................................................
..................................................................................................................................................................
..................................................................................................................................................................
Notes
39
Distribued by :
B.P.12 - 76550 Ambrumesnil - France Tél : 33 (0)2 35 83 06 44 33 (0)2 35 83 03 86 Fax : 33 (0)235 85 36 72 www.devatec.com Email : [email protected]
Perfume dispensor ordesinfecting tank
Steam bathcontrolcabinet
Sensor
Perfume dispensoror desinfecting
Desinfecting nozzle
Steam nozzle
Photos no contractual
DEVATEC continue to develop its productFor this reason, the technical data and specificationof the product must be changed without prior notice.
Serpentin