7/28/2019 Sm 1000 4905 SixAndSevenPositionCylinder
http://slidepdf.com/reader/full/sm-1000-4905-sixandsevenpositioncylinder 1/9
The six and seven position cylinders are medium duty pneumatic
positioning devices that operate through six or seven predetermined
positions of ½” (12.7 mm) increments with total strokes of 2½” (63.5
mm) or 3” (76.2 mm) respectively. They were primarily designed for
power-shift transmissions but may also be utilized for indexing and
any other application where fixed stroke increments are required.
The ideal companion valve for these cylinders is Type "P" six or
seven position Rotair®Valve. An alternative control is an electro-
pneumatic switching circuit using 3-way solenoid valves. Thesecylinders are extremely rugged having anodized, corrosion resistant,
lightweight aluminum body, pistons and pistons stops.
WARNING: INSTALLATION ANDMOUNTING
The user of these devices must conform to all applicable electrical,mechanical, piping and other codes in the installation, operation orrepair of these devices.
INSTALLATION! Do not attempt to install, operate or repair thesedevices without proper training in the technique of working onpneumatic or hydraulic systems and devices, unless under trainedsupervision.Compressed air and hydraulic systems contain high levels of storedenergy. Do not attempt to connect, disconnect or repair theseproducts when a system is under pressure. Always exhaust or drainthe pressure from a system before performing any service work.Failure to do so can result in serious personal injury.
MOUNTING! Devices should be mounted and positioned in such amanner that they cannot be accidentally operated.
INSTALLATION
Mount the cylinders in any desirable plane to a sturdy, flat surface
(preferably with the ports facing down) with three 3/8" bolts.
Mounting lugs are cast in the body of the cylinders. Avoid
misalignment with the load to be positioned since side thrust and
binding will affect the service life of the rod bearing and piston stop
seals.
All ports are 1/4”-18 NPT. The following ports should be pipedtogether with "T" connections: 3 with 3A on the six position cylinder,3 with 3A and 6 with 6A on the seven position cylinder. Connectionsshould be made as close to the cylinder as possible to reduce thenumber of lines from the control valve.
OPERATION
Maximum operating pressure is 150 psi (10 bar) within a
temperature range of -40° to 200°F (-40° to 93°C). The cylinder
piston rod reaches its various positions in response to pressure
being supplied to the cylinder ports as shown in the truth tables on
pages 3 and 5. V means air must be vented to atmosphere, S
means air must be supplied and S/V means port can be supplied or
vented. whichever is most convenient in the control valve. Each
cylinder has reverse at full extended position of the rod and is spring
returned to neutral (next position in from reverse) from any position.
The transmissions which these cylinders usually control have the full
automatic or drive position adjacent to neutral. The corresponding
position is 5 on the seven position and 4 on the six position cylinder.
The sequential order of cylinder positions is a function of the "P"
Rotair Valve.
The forces developed by the cylinder are functions of the airpressure applied to the exposed piston areas and are tabulated forrod movement to the various stroke positions as shown on thecharts on pages 6 and 7. The internal spring returns the piston rod to its Neutral position whenair pressure is intentionally or unintentionally exhausted from allcontrol lines. This safety feature returns the transmission to neutralif the air supply is lost.
MAINTENANCE
Periodically disassemble the cylinder for cleaning and inspection.Clean all metal parts with a nonflammable solvent and wash allrubber parts with soap and water. Rinse thoroughly and dry, using
low pressure jet, if available. Replace all damaged or worn parts.Reassemble the cylinder, lubricating each part as it is put in place.Rubber parts should be lubricated with Dow Corning No. 55pneumatic grease. Check the operation of the reassembled cylinderby putting low pressure air in the ports in accordance with the truthtable, pages 3 and 5.
NOTE: When disassembling a cylinder, please use CAUTION asthe return springs are under compression.
ADJUSTMENT
REXROTH six and seven positions require no adjustment.
SIX R431006322 (P -063892-00001) AND SEVEN R431006321 (P -063981--00002)
POSITION CYLINDERS
Service Information
SM-1000.4905
NOTE:
“P” Rotair Valve R431006324 (P -063984-00000) was designed to control
six position cylinder R431006322 (P-063982-00001) and valve R431006326(P -063985-00000) was designed to control seven position cylinder
R431006321 (P -063981-00002). Both of these Rotair Valves have first
gear position adjacent to neutral and progress toward full automatic at the
extreme position of valve handle travel Rotair Valves can be made available
to have the handle position sequence identical to the transmission. Six
position Rotair R431006324 (P -063984-00000) should be connected as
follows:
Ports No. 1 and No. 5 plugged, Exhaust port is 1/8” NPT, pressure is
supplied to unnumbered port in the side of the pipe bracket, valve port No. 2
to cylinder port No. 2, valve No. 4 to cylinder No. 5, valve No. 3 to cylinder
No. 3 & 3a, and valve port No. 6 to cylinder port No. 6A in six position
cylinder R431006322 (P -063982-00001).
Seven position Rotair R431006326 (P -063985-00000) should be connected
as follows: port No. 1 plugged, exhaust port No. 4, pressure is supplied to
unnumbered port in the side of the pipe bracket, valve port No. 2 to cylinder
port No. 2, valve No. 5 to cylinder No. 5, valve No. 3 to cylinder No. 3 & No.3A and valve port No. 6 to cylinder No. 6 & 6A in seven position cylinder
R431006321 (P -063981-00002).
7/28/2019 Sm 1000 4905 SixAndSevenPositionCylinder
http://slidepdf.com/reader/full/sm-1000-4905-sixandsevenpositioncylinder 2/9
Page 2
EXPLODED VIEWSix Position
R431006322 (P –063982-00001
7/28/2019 Sm 1000 4905 SixAndSevenPositionCylinder
http://slidepdf.com/reader/full/sm-1000-4905-sixandsevenpositioncylinder 3/9
Page 3
SIX POSITION CYLINDER PARTS LISTM-4-N-1B CYLINDER P/N R431006322 (P -063982-00001)
DWG. NO. CP63982A
ITEM NO. QTY. DESCRIPTION NEW P/N OLD P/N
1 4 SCREW, 1/4 X 20 X 3/4 CAP R431002203 P -049856-00046
2 1 PISTON 2 7/8 R431002303 P -064175-00000
*3 1 O-RING, 2 3/4 See Kit See Kit
*4 2 O-RING, 2 O.D. See Kit
5 1 PISTON, 2 REAR R431006371 P -064184-00000
6 1 BODY, CYLINDER R431006377 P -064193-00000
7 1 SCREW, CAP HEX, HEAD R431002232 P -049832-00078
8 1 WASHER, LOCK 5/16 R431002572 P -049982-00006
*9 1 PISTON, 1 3/4 R431006374 P -064189-00000
*10 1 O-RING, 1 3/4 O.D. See Kit
*11 3 O-RING, 11/16 O.D. See Kit
12 1 PISTON, 2 FRONT R431006909 P -066884-00000
13 1 PISTON, 1 5/8 R431006365 P -064172-00000
*14 1 O-RING, 1 1/2 O.D. See Kit
15 1 PISTON 2 7/8 R431006910 P -066885-00000
*16 1 O-RING, 2 7/8 O.D. See Kit
*17 1 O-RING, 3 3/8 O.D. See Kit*18 1 O-RING, 1 5/8 O.D. See Kit
19 1 RING, RET. 1 5/8 R431002387 P -049882-00010
20 1 HOUSING, BUSHED SPRING R431000896 P -028264-00001
21 1 SPRING R431006375 P -064191-00000
22 1 ROD, PUSH COMPLETE R431006563 P -065103-00001
23 1 RETAINER, SPRING R431006908 P -066883-00000
24 1 BUSHING R431006366 P -064173-00000
*25 1 WIPER, ROD 1/2 See Kit
26 4 SCREW, CAP 1/4-20X1 R431002303 P -049856-00046
Recommended Spare Parts - *Packing Repair Kit P/N R431006546 (P -064997-00001)Spring P/N R431006375 (P -064191-00000)
CONDITION OF PORTS
CYLINDERPOSITION CAVITY
3 2 5 3A 6A
R S V S V V V
N S V V V V V
4 S V V V V S
3 S V V V S V
2 S V S S V S V
1 V V S S V S V
S SUPPLIED V VENTED
7/28/2019 Sm 1000 4905 SixAndSevenPositionCylinder
http://slidepdf.com/reader/full/sm-1000-4905-sixandsevenpositioncylinder 4/9
Page 4
EXPLODED VIEWSeven Position
R431006321 (P –063981-00002
7/28/2019 Sm 1000 4905 SixAndSevenPositionCylinder
http://slidepdf.com/reader/full/sm-1000-4905-sixandsevenpositioncylinder 5/9
Page 5
SEVEN POSITION CYLINDER PARTS LISTM5-N-1B P/N R431006321 (P -063981-00002)
DWG. NO. CP63981A
ITEM NO. QTY. DESCRIPTION NEW P/N OLD P/N
1 1 CAP R431006372 P -064186-0000
2 1 ROD, REAR PISTON R431006373 P -064188-0000
3 1 PISTON, 2 1/4 R431006376 P -064192-0000
*4 12 O-RING, 2 1/4 O.D. See Kit See Kit*5 1 O-RING, 5/8 O.D. See Kit See Kit
*6 2 O-RING, 2 3/4 O.D. See Kit See Kit
*7 1 O-RING, 2 O.D. See Kit See Kit
8 1 PISTON, 2 REAR R431006370 P -064183-00000
9 1 BODY, CYLINDER R431006377 P -064193-00000
10 1 SCREW, CAP HEX. HEAD R431002232 P -049832-00078
11 1 WASHER, LOCK 5/16 R431002572 P -049982-00006
12 1 PISTON, 1 3/4 R431006374 P -064189-00000
*13 13 O-RING, 1 3/4 O.D. See Kit See Kit
*14 1 O-RING, 11/16 O.D. See Kit See Kit
15 1 PISTON, 2 FRONT R431006909 P -066884-00000
16 1 PISTON, 1 5/8 R431006365 P -064172-00000
*17 1 O-RING, 1 1/2 O.D. See Kit See Kit
18 1 PISTON, 2 7/8 R431006910 P -066885-00000
*19 1 O-RING, 1 7/8 O.D. See Kit See Kit
*20 1 O-RING, 3 3/8 O.D. See Kit See Kit
*21 1 O-RING, 1 5/8 O.D. See Kit See Kit
22 1 RING, RET. 1 5/8 R431002333 P -049857-00007
23 1 HOUSING, SPRING R431000896 P -028264-00001
24 1 SPRING R431006375 P -064191-00000
25 1 ROD, PUSH COMPLETE R431006562 P -065103-00000
26 1 RETAINER, SPRING R431006908 P -066883-00000
27 1 BUSHING R431006366 P -064173-00000
*28 1 WIPER, ROD 1/2 See Kit See Kit
29 2 RING, RET. 1/2 R431002333 P -049857-00007
30 8 SCREW, CAP 1/4-20X1 R431002303 P -049856-00046
Recommended Spare Parts - *Packing Repair Kit P/N R431006546 (P -064997-00001)Spring P/N R431006375 (P -064191-00000)
CONDITION OF PORTS
CYLINDERPOSITION
CAVITY
6 3 2 5 3A
R S V S V S V V
N S V S V V V V
5 S V S V V V V
4 S V S V V V S
3 S V S V S S V
2 S V V S S V
S SUPPLIED V VENTED
1 V V V S S V
6A
V
V
S
V
S V
S V
S V
ASSEMBLY VIEW
7/28/2019 Sm 1000 4905 SixAndSevenPositionCylinder
http://slidepdf.com/reader/full/sm-1000-4905-sixandsevenpositioncylinder 6/9
Page 6
SIX POSITION CYLINDER
7/28/2019 Sm 1000 4905 SixAndSevenPositionCylinder
http://slidepdf.com/reader/full/sm-1000-4905-sixandsevenpositioncylinder 7/9
Page 7
SEVEN POSITION CYLINDER
7/28/2019 Sm 1000 4905 SixAndSevenPositionCylinder
http://slidepdf.com/reader/full/sm-1000-4905-sixandsevenpositioncylinder 8/9
7/28/2019 Sm 1000 4905 SixAndSevenPositionCylinder
http://slidepdf.com/reader/full/sm-1000-4905-sixandsevenpositioncylinder 9/9
International offices:
Asia:
China RussiaIndia SingaporeJapan South Korea
Malaysia
Australia
Europe:
Austria NetherlandsBelgium NorwayBulgaria Poland Czech Republic PortugalDenmark Romania
Finland SlovakiaFrance SpainGermany Sweden
Greece Switzerland Hungary TurkeyItaly Ukraine
United Kingdom
North America:
Canada United StatesMexico
South America:
Argentina Venezuela
Brazil
Bosch Rexroth Corporation
Pneumatics1953 Mercer Road
Lexington, KY 40511-1021Telephone (859) 254-8031Facsimile (859) 254-4188 [email protected]
www.boschrexroth-us.com/brp
Factory Automation
Regional sales offices:
Central
Bosch Rexroth Corporation5150 Prairie Stone Parkway
Hoffman Estates, IL 60192-3707Telephone (847) 645-3600Facsimile (847) 645-0804
Great Lakes
Bosch Rexroth Corporation2730 Research Drive
Rochester Hills, MI 48309Telephone (248) 393-3330Facsimile (248) 393-2893
Northeast
Bosch Rexroth Corporation
99 Rainbow Road East Granby, CT 06026-0000Telephone (860) 844-8377
Facsimile (860) 844-8595
Bosch Rexroth Corporation
2315 City Line Road Bethlehem, PA 18017-2131Telephone (610) 694-8300
Facsimile (610) 694-8467
SoutheastBosch Rexroth Corporation14001 South Lake DriveCharlotte, NC 28273-5544Telephone (704) 583-4338
Facsimile (704) 583-0523
West
Bosch Rexroth Corporation11 Goddard Irvine, CA 92618-4600
Telephone (949) 450-2777Facsimile (949) 450-2790
North American offices:
Bosch Rexroth CorporationCorporate Headquarters
5150 Prairie Stone ParkwayHoffman Estates, IL 60192-3707Telephone (847) 645-3600
Facsimile (847) 645-0804
Bosch Rexroth Corporation
Industrial Hydraulics2315 City Line Road
Bethlehem, PA 18017-2131Telephone (610) 694-8300
Facsimile (610) 694-8467
Bosch Rexroth Corporation
Electric Drives and Controls5150 Prairie Stone ParkwayHoffman Estates, IL 60192-3707
Telephone (847) 645-3600Facsimile (847) 645-6201
Bosch Rexroth CorporationLinear Motion and AssemblyTechnologies
816 E. Third StreetBuchanan, MI 49107Telephone (269) 695-0151
Facsimile (269) 695-5363
14001 South Lakes DriveCharlotte, NC 28273Telephone (800) 438-5983Facsimile (704) 583-0523
Bosch Rexroth CorporationMobile Hydraulics145 Southchase Boulevard
Fountain Inn, SC 29644-9018Telephone (864)967-2777Facsimile (864)962-5338
Bosch Rexroth Canada3426 Mainway DriveBurlington, Ontario L7M 1A8 Telephone (905)
335-5511 Facsimile (905) 335-4184www.boschrexroth.ca
Bosch Rexroth, S.A. de C.V.Calle Neptuno # 72Unidad Industrial Vallejo
CP 07700 Mexico, D.F.Telephone (555) 754-1711
Facsimile (555) 752-5943
Further contacts:www.boschrexroth.com/addresses
The data specified herein only serves todescribe the product. No statements
concerning a certain condition or suitabilityfor a certain application can be derived from
our information. The given information doesnot release the user from obligation of own judgment and verification. It must beremembered that our products are subject to a
natural process of wear and aging. ©Thisdocument, as well as the data, specificationsand other information set forth in it, are the
exclusive property of Bosch Rexroth Corp.Without their con- sent it may not bereproduced or given to third parties.
Printed in the United StatesSM-1000.4905
(Supercedes B3-49.05)December 2008
©2008 Bosch Rexroth Corporation