SIMS-201
Wire and Fiber Transmission Systems
2
Overview
Chapter 15Wire and Fiber Transmission
Systems Wire as a transmission medium Fiber optics as a transmission
medium
3
Introduction There are fundamentally two mediums for
information transmission: Guided electromagnetic (EM) waves - wire, fiber
optics, etc. Unguided EM waves - air
The past two lectures have concentrated on radio communications using air as the transmission medium
Next, we will learn about some important aspects of the forms of wire and fiber optics used for information transmission
4
Air
Cable
Fiber optics
Guided
Unguided
5
Wire as a Transmission Medium
Wire is currently the most common and versatile medium of transmission
All wire-based transmission media are called cables
Wire based transmission schemes guide electromagnetic waves either between a pair of separate wires or inside a coaxial (coax) arrangement
A coax cable has both a center conductor and a second shield conductor
These conductors are separated by an insulating material, such that the shield conductor entirely surrounds the center conductor
6
In the case of non coaxial transmission, the pair of wires may be held either parallel to each other by a stiff insulating material, or individually insulated and twisted around each other
A surrounding shield may be placed around the resulting twisted pair to form a shielded twisted pair (STP)
If a surrounding shield is not placed around the twisted pair, then this arrangement is called an unshielded twisted pair (UTP)
7
Parallel wires
UTP
STP
Coax
8
Cable characteristics A cable moves EM waves by providing a channel. The EM
waves traverse the cable moving through the conductors. The EM waves are confined in this way, as they interact with the free electrons in the conductor, which are responsible for guiding the waves.
While traversing through the cable however, due to physical effects, the wave loses energy and the intensity of the wave diminishes, the farther it goes.
This results in a decrease of the signal amplitude at the receiving end – called attenuation
In other words, the magnitude of the signal diminishes as it reaches the end of the cable Original signal Attenuated signal
9
The longer the cable, the larger the attenuation
The larger the conductor in the cable (radius), the lower the attenuation (up to some extent)
It is desirable to use larger, more expensive cables in situations that require high transmission quality over long distances
High transmission quality means that the receiver is able to detect correctly if a 1 or a 0 is transmitted
If a signal is highly attenuated at the receiving end, the receiver will not be able to distinguish between the levels of 1 and 0, and this will lead to erroneous transmission of information
10
Typical attenuation figures for various cables:
Cable type Signal attenuation per 1000 ft @100
MHz
UTP 56 dB
STP 37.5 dB
Coax (thin ethernet)
60 dB
Coax (thick ethernet)
20 dB
Cheap
Expensive
11
What is a decibel? In electrical engineering, the decibel (abbreviated
as dB) is a logarithmic unit used to describe the ratio between two power levels
Power: unit of measurement is watts (W) dB = 10 log10 P1/P2 (power ratio)
The Decibel
12
If the input signal power is 2 W and the output signal power is measured to be 2 milliWatts, calculate the power attenuation in dB of the cable
Original signal Attenuated signal2W input power
2mW output power
Example
The input signal power is: P1=2 W
The output signal power is: P2=2x10-3 W
The Power attenuation is: dBP = 10 log10 P1/P2
=10 log10 2/(2x10-3)
= 10 log10 1000=10 x 3
=30 dBThe signal power has attenuated by 30dB while passing through the cableNote: Since P1/P2 = 1000, we can say that the signal has suffered a power
attenuation of 1000 times, or in other words, by 30 dB
Length of cable
13
Logarithm (log)
How do we know that 10 log10 1000 = 10 x 3 ?
Logarithmic and Exponential Functions Logarithmic and exponential functions are inverses of each other:
If y = logbx then x = by
In words, logb x is the exponent you put on base b to get x. lol So,
If x = log10 1000 then 1000 = 10x and how much is x here? 10 to the power of what is
equal to 1000? It would be 10 to the power of 3 (10x10x10) = 1000.
14
If the power attenuation of a length of cable is given to be 15 dB, find the ratio of the input/output power
15 = 10log10 P1/P2 1.5 = log10 P1/P2 P1/P2 = 101.5 = 31.62P1/P2 = 31.62
The calculation above illustrates that signals passing through this length of cable suffer a power attenuation by 31.62 times. Note that this is a ratio! There are no units.
If, for example, the input power is 1W, the power at the output of the cable would be 1/31.62=0.0316 W
Logarithm: if b = logax then x = ab
Example
1.5 = log10 P1/P2 then P1/P2 = 101.5
15
Note that the dB scale is a logarithmic scale, and is a convenient method to express large ratios
In the first example, the ratio 1000 was expressed as 30 dB
For example, if the ratio is: 800,000,000, then this expressed in dB is: 89 dB (a much smaller number)
Ratio dB
1 0
10 10
100 20
1000 30
10,000 40
100,000 50
1,000,000 60
Note..
16
Exercises
If the input signal power is 10mW (milliWatts) and the output signal power is measured to be 5 μW (micro watts), calculate the power attenuation in dB of the cable
If the power attenuation of a length of cable is given to be 65 dB, find the ratio of the input/output power
17
Fiber Optics as a Transmission Medium Information is carried through a fiber optic cable by transmitting
pulses of light (which is also an EM wave)! A fiber optic cable is a coaxial arrangement of glass or plastic
material of immense clarity (i.e., highly transparent) A clear cylinder of optical material called the core is surrounded by
another clear wrapper of optical material called the cladding These two materials are selected to have different indices of
refraction The fiber is surrounded by a plastic or teflon jacket to protect and
stiffen the fiber Light is guided through the optical fiber by continual reflection from
the core-cladding boundary This is made possible due to the different refractive indices of the
core and cladding materials The index of refraction (n) of a material affects the angle by which a
light ray is bent while passing through the material If the light incident on the core-cladding boundary is at a suitable
angle, then the light will be totally reflected from the boundary. This is called total internal reflection
18
Cross section of optical fiber cable
19
Core-cladding boundary
Core and cladding with different indices of refraction
20
Let us look at some useful fiber optics demos:
http://www.eas.asu.edu/~palais/demos/demos.htm
http://electronics.howstuffworks.com/fiber-optic2.htm
21
Advantages of fiber optics
Much Higher Bandwidth (Gbps) - Thousands of channels can be multiplexed together over one strand of fiber
Immunity to Noise - Immune to electromagnetic interference (EMI). Safety - Doesn’t transmit electrical signals, making it safe in
environments like a gas pipeline. High Security - Impossible to “tap into.” Less Loss - Repeaters can be spaced 75 miles apart (fibers can be made
to have only 0.2 dB/km of attenuation) Reliability - More resilient than copper in extreme environmental
conditions. Size - Lighter and more compact than copper. Flexibility - Unlike impure, brittle glass, fiber is physically very flexible.
Disadvantages include the cost of interfacing equipment necessary to convert electrical signals to optical signals. (optical transmitters, receivers) Splicing fiber optic cable is also more difficult.