SIDE PANEL FOR 8mm FRAMELESS CONCEALED HINGE DOOR
VictoriaPlum.com0344 804 48 48
We’ve made our packaging more eco-friendly,replacing plastics with recyclable reinforced cardboard. It is just as effective at protecting your product, passing strict quality control tests
Refer to sheet 11 for relevant product codes
Decide which hand is required. Right hand opening illustrated.Change the hand by turning the side panel upside down.
1
BEFORE YOU START, HERE IS SOME IMPORTANT INFORMATION
1) General Information
2) Additional Notes
Please inspect this product upon delivery, any missing parts or manufacturing
defects must be reported immediately to the supplier. Damage or defects reported
later will not be accepted. TAKE CARE WHEN HANDLING GLASS PARTS - AVOID
HEAVY CONTACT BETWEEN THE GLASS EDGES AND ANY HARD SURFACE.
Glass breakage claims will not be accepted after the product has been unpacked.
Please note: Aluminium is a soft metal, and undergoes a series of extrusion,
fabrication, polishing and anodising processes in order to create your finished
shower enclosure. Some light surface marks are normal, and is a result of the
manufacturing processes. Quality control has ensured that this item is of a good
standard, and is fit for purpose.
Please read these instructions carefully before starting installation.Special care should be taken when drilling walls to avoid hidden pipes or electrical cables.
Note: this product is heavy and may require two people to install.
TOOLS REQUIRED
This product is heavy and may require two people to install.
Ø3mm Drill bit
Ø6mm Drill bit
Pencil
Spirit level
Tape measure
DESCRIPTION DESCRIPTIONPART IMAGE PART IMAGE
Drill
Flat-headScrewdriver
Cross headScrewdriver
Silicone Sealant
PZ1
Mallet
2
(1)
(2)
(3)
(4)
(7)
(5)
(8)
(6)
(9)
(1) 1x Glass clamp
(2) 1x Upright profile top cap
(3) 1x Wall profile
(4) 1x Wall profile cover strip
(7) 4x Wall plugs
(5) 1x Fixed panel
(8) 4x Screws 4*30
(6) 2x Magnet seals
(9) 3x Screws 4*12
PACK I.D
E
E
B
B
E
A
E
C
E
ASSEMBLY INSTRUCTIONS - DRAWING+SIDE PANELNB: ALL MEASUREMENTS + COMPONENT SIZES QUOTED ARE IN MM.
3
BOX CONTENTS
Component
(1) 1x Glass clamp
(2) 1x Upright profile top cap
(3) 1x Wall profile
(4) 1x Wall profile cover strip
(5) 1x Fixed panel
(6) 2x Magnet seals
(7) 4x Wall plugs
(8) 4x Screws 4*30
(9) 3x Screws 4*12
PACK I.D
E
E
B
B
A
C
E
E
E
Picture
THESE DIMENSIONS ASSUME THE WALLS ARE PLUMB AND THE SHOWER TRAY IS LEVEL, AND THAT THE WALLS ARE TILED DOWN TO THE TOP OF THE TRAY USING A 10mm TILE/WET WALL PANEL.
ASSEMBLY INSTRUCTIONSIf you require help, we advise you to contact a competent plumber .
FITTED DOOR AND SIDE PANEL DRAWING
Installation Steps7
60/
80
0/9
0/
10
00
900/ 1000/ 1200/ 1400
20
02
0
4
STEP 1 CHECK BOX CONTENTS ARE CORRECT AND THEN MEASURE KEY COMPONENTS.
STEP 2 DRAWING TO SHOW CORRECT SHOWER TRAY INSTALLATION
WALL
TILE OR WETWALL PANEL
SHOWER TRAY
YES
WALL
TILE OR WETWALL PANEL
SHOWER TRAY
NO
STEP 3 TRAY TO BE LEVELMAKE SURE THE TRAY IS LEVEL, USING A SPIRIT LEVEL, BEFORE INSTALLING THISSHOWER PANEL / DOOR, AND THAT SILICONE IS APPLIED ON ALL SIDES WHERE THETRAY MEETS THE TILES / WET WALL PANELS.
1950x701x8
1950x39 1950x39 1950x39 1950x39 1950x39Wall post
1950x741x8 1950x841x8 1950x941x8 1950x741x8
LSP1002LSP7602 LSP802 LSP902 LSP802BLK
Measurement Matrix (before assembly) Dimension in mmUnits supplied loose for self assembly
Flat fixed panel glass (including fixed panel profiles if attached)
5
STEP 8 SLIDE WALL PROFILE ON TO THE SIDE PANEL
STEP 9 MARK THE CORRECT DRILL HOLE POSITIONS ON THE WALL
FIRST: COMPLETE STEPS 4-7 IN THE DOOR ASSEMBLY INSTRUCTIONS
6
STEP 10 DRILL AND SCREW THE WALL PROFILE TO THE WALL
STEP 11 PUSH THE MAGNET SEALS AND VERTICAL PANEL SEALS ON TO THE GLASS DOOR AND SIDE PANEL
1
6.0mm
x4
St4x303
x4
2x4
21 3
8
9
15mm4
5
12mm6
7
Movingpanel
Movingpanel
Fixedpanel
Fixedpanel
7
STEP 12 SECURING THE SIDE PANEL, FIXED PANEL AND PROFILE COVER STRIPS
STEP 13 FITTING THE TOP BAR, WALL BRACKET AND GLASS CLAMPS
Take care not to drill into the glass
L=0~20mmL≥5mm/R≥10mm
R
L≤5mm/R≥15mm
1
2
3
50~100mm
1 2
1
2
3
4
5
ST4X30
6.0mm
150mm
150mm
2
St4x12
1
3.0mm
x6
x6
3
x6
8
STEP 14 FITTING THE BOTTOM DRIP STRIP
STEP 15 FITTING THE TOP CAPS AND HANDLE
1
3
4
2
4
9
STEP 16 SILICONE THE OUTSIDE EDGES
24 hours
Allow 24 hours for silicone to dry before use. Silicone on the
outside edge only, NOT THE INSIDE
10
CARE AND MAINTENANCE
COMMITMENT TO QUALITY
1) AFTER CARE INSTRUCTIONS
2) MAINTENANCE
Regularly clean your shower product with warm soapy water
Clean the plastic parts with a cloth and mild detergent. Never
use any abrasive creams, dissolvents, acetone or detergents
and disinfectants that contain chlorine. The supplier acceptsno liability for any type of use of care other than those contained
in these instructions. The supplier reserves the right to introduce
technical changes without notice.
It is our intention that the quality and functions of this productare of the highest standard. If you require help we advise you
firstly contact a competent plumber. However we understand that
this may not always be the case, so should you experience
any problems please contact our customer services quoting
the following:
Customer help line number: 0344 804 48 48
to prevent lime scale build up. Do not use abrasive cleaning
fluids or materials, or strong chemical cleaners as this will
damage the product surface.
Product name:
Product code: LSP7602 / LSP802 / LSP902 / LSP1002 / LSP802BLK
Side Panel For 8mm Frameless Concealed Hinge door
11
12
INSTALLERS NOTES
13
INSTALLERS NOTES
14
INSTALLERS NOTES
The packaging you have received with your product is 100% recyclable.It must be disposed of in a safe and environmentally friendly way.
We suggest you take it to the local landfill site and discard in the designated bins.
Victoria Plum Limited, Bridgehead Business Park Hessle, HU13 0DG
16
EN 14428:2004+A1:2008
DOP No.:J160415002
Shower enclosures with aluminiumprofiles and safety glass
Essentialcharacteristics
Performance Harmonisedtechnical
specificationCleanability
Impactresistance/shatter
properties
Pass
Pass
PassDurability
Clause 4.2 of EN14428:2004+A1:
2008Clause 4.3 of EN14428:2004+A1:
2008Clause 4.4 of EN14428:2004+A1:
2008
V08/07/2020